Whenever bridge driver hits the max capacity of MDBs, it disables
the MC processing (by setting corresponding bridge option), but never
notifies switchdev about such change (the notifiers are called only upon
explicit setting of this option, through the registered netlink interface).
This could lead to situation when Software MDB processing gets disabled,
but this event never gets offloaded to the underlying Hardware.
Fix this by adding a notify message in such case.
Fixes: 147c1e9b90 ("switchdev: bridge: Offload multicast disabled")
Signed-off-by: Oleksandr Mazur <oleksandr.mazur@plvision.eu>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Link: https://lore.kernel.org/r/20220215165303.31908-1-oleksandr.mazur@plvision.eu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As reported[1] if startup query interval is set too low in combination with
large number of startup queries and we have multiple bridges or even a
single bridge with multiple querier vlans configured we can crash the
machine. Add a 1 second minimum which must be enforced by overwriting the
value if set lower (i.e. without returning an error) to avoid breaking
user-space. If that happens a log message is emitted to let the admin know
that the startup interval has been set to the minimum. It doesn't make
sense to make the startup interval lower than the normal query interval
so use the same value of 1 second. The issue has been present since these
intervals could be user-controlled.
[1] https://lore.kernel.org/netdev/e8b9ce41-57b9-b6e2-a46a-ff9c791cf0ba@gmail.com/
Fixes: d902eee43f ("bridge: Add multicast count/interval sysfs entries")
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As reported[1] if query interval is set too low and we have multiple
bridges or even a single bridge with multiple querier vlans configured
we can crash the machine. Add a 1 second minimum which must be enforced
by overwriting the value if set lower (i.e. without returning an error) to
avoid breaking user-space. If that happens a log message is emitted to let
the administrator know that the interval has been set to the minimum.
The issue has been present since these intervals could be user-controlled.
[1] https://lore.kernel.org/netdev/e8b9ce41-57b9-b6e2-a46a-ff9c791cf0ba@gmail.com/
Fixes: d902eee43f ("bridge: Add multicast count/interval sysfs entries")
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The sequence count bridge_mcast_querier::seq is protected by
net_bridge::multicast_lock but seqcount_init() does not associate the
seqcount with the lock. This leads to a warning on PREEMPT_RT because
preemption is still enabled.
Let seqcount_init() associate the seqcount with lock that protects the
write section. Remove lockdep_assert_held_once() because lockdep already checks
whether the associated lock is held.
Fixes: 67b746f94f ("net: bridge: mcast: make sure querier port/address updates are consistent")
Reported-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Mike Galbraith <efault@gmx.de>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Link: https://lore.kernel.org/r/20210928141049.593833-1-bigeasy@linutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Before vlan/port mcast router support was added
br_multicast_set_port_router was used only with bh already disabled due
to the bridge port lock, but that is no longer the case and when it is
called to configure a vlan/port mcast router we can deadlock with the
timer, so always disable bh to make sure it can be called from contexts
with both enabled and disabled bh.
Fixes: 2796d846d7 ("net: bridge: vlan: convert mcast router global option to per-vlan entry")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
br_ip6_multicast_mld2_report function uses icmp6h
to parse mld2_report packet.
mld2r_ngrec defines mld2r_hdr.icmp6_dataun.un_data16[1]
in include/net/mld.h.
So, it is more compact to use mld2r rather than icmp6h.
By doing printk test, it is confirmed that
icmp6h->icmp6_dataun.un_data16[1] and mld2r->mld2r_ngrec are
indeed equivalent.
Also, sizeof(*mld2r) and sizeof(*icmp6h) are equivalent, too.
Signed-off-by: MichelleJin <shjy180909@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The per-vlan router option controls the port/vlan and host vlan entries'
mcast router config. The global option controlled only the host vlan
config, but that is unnecessary and incosistent as it's not really a
global vlan option, but rather bridge option to control host router
config, so convert BRIDGE_VLANDB_GOPTS_MCAST_ROUTER to
BRIDGE_VLANDB_ENTRY_MCAST_ROUTER which can be used to control both host
vlan and port vlan mcast router config.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change br_multicast_set_port_router to take port multicast context as
its first argument so we can later use it to control port/vlan mcast
router option.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When changing vlan mcast state by br_multicast_toggle_vlan it iterates
over all ports and enables/disables the port mcast ctx based on the new
state, but I forgot to update the host vlan (bridge master vlan entry)
with the new state so it will be left out. Also that function is not
used outside of br_multicast.c, so make it static.
Fixes: f4b7002a70 ("net: bridge: add vlan mcast snooping knob")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to account for the IPv6 attributes when dumping querier state.
Fixes: 5e924fe6ccfd ("net: bridge: mcast: dump ipv6 querier state")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was a dumb error I made instead of writing nla_total_size(0)
for a nest attribute, I wrote nla_total_size(sizeof(0)).
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 606433fe3e11 ("net: bridge: mcast: dump ipv4 querier state")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A minor improvement to avoid dumping mcast ctx querier state if snooping
is disabled for that context (either bridge or vlan).
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for dumping global IPv6 querier state, we dump the state
only if our own querier is enabled or there has been another external
querier which has won the election. For the bridge global state we use
a new attribute IFLA_BR_MCAST_QUERIER_STATE and embed the state inside.
The structure is:
[IFLA_BR_MCAST_QUERIER_STATE]
`[BRIDGE_QUERIER_IPV6_ADDRESS] - ip address of the querier
`[BRIDGE_QUERIER_IPV6_PORT] - bridge port ifindex where the querier
was seen (set only if external querier)
`[BRIDGE_QUERIER_IPV6_OTHER_TIMER] - other querier timeout
IPv4 and IPv6 attributes are embedded at the same level of
IFLA_BR_MCAST_QUERIER_STATE. If we didn't dump anything we cancel the nest
and return.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for dumping global IPv4 querier state, we dump the state
only if our own querier is enabled or there has been another external
querier which has won the election. For the bridge global state we use
a new attribute IFLA_BR_MCAST_QUERIER_STATE and embed the state inside.
The structure is:
[IFLA_BR_MCAST_QUERIER_STATE]
`[BRIDGE_QUERIER_IP_ADDRESS] - ip address of the querier
`[BRIDGE_QUERIER_IP_PORT] - bridge port ifindex where the querier was
seen (set only if external querier)
`[BRIDGE_QUERIER_IP_OTHER_TIMER] - other querier timeout
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can consolidate both functions as they share almost the same logic.
This is easier to maintain and we have a single querier update function.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a sequence counter to make sure port/address updates can be read
consistently without requiring the bridge multicast_lock. We need to
zero out the port and address when the other querier has expired and
we're about to select ourselves as querier. br_multicast_read_querier
will be used later when dumping querier state. Updates are done only
with the multicast spinlock and softirqs disabled, while reads are done
from process context and from softirqs (due to notifications).
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when a querier port is detected its net_bridge_port pointer is
recorded, but it's used only for comparisons so it's fine to have stale
pointer, in order to dereference and use the port pointer a proper
accounting of its usage must be implemented adding unnecessary
complexity. To solve the problem we can just store the netdevice ifindex
instead of the port pointer and retrieve the bridge port. It is a best
effort and the device needs to be validated that is still part of that
bridge before use, but that is small price to pay for avoiding querier
reference counting for each port/vlan.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to change and retrieve global vlan multicast router state
which is used for the bridge itself. We just need to pass multicast context
to br_multicast_set_router instead of bridge device and the rest of the
logic remains the same.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to change and retrieve global vlan multicast querier state.
We just need to pass multicast context to br_multicast_set_querier
instead of bridge device and the rest of the logic remains the same.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is a minor optimization and better behaviour to make sure querier and
query sending routines affect only the matching multicast context
depending if vlan snooping is enabled (vlan ctx vs bridge ctx).
It also avoids sending unnecessary extra query packets.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to have the querier state per multicast context in order to have
per-vlan control, so remove the internal option bit and move it to the
multicast context. Also annotate the lockless reads of the new variable.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to change and retrieve global vlan IGMP/MLD versions.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding bridge multicast context support for host-joined groups is easy
because we only need the proper timer value. We pass the already chosen
context and use its timer value.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the recent change to use bridge/port multicast context pointers
instead of bridge/port I missed to convert two locations which pass the
port pointer as-is, but with the new model we need to verify the port
context is non-NULL first and retrieve the port from it. The first
location is when doing querier selection when a query is received, the
second location is when leaving a group. The port context will be null
if the packets originated from the bridge device (i.e. from the host).
The fix is simple just check if the port context exists and retrieve
the port pointer from it.
Fixes: adc47037a7 ("net: bridge: multicast: use multicast contexts instead of bridge or port")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new global vlan option which controls whether multicast snooping
is enabled or disabled for a single vlan. It controls the vlan private
flag: BR_VLFLAG_GLOBAL_MCAST_ENABLED.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the port multicast context to check if the router port is a vlan and
in case it is include its vlan id in the notification.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add basic vlan context querier support, if the contexts passed to
multicast_alloc_query are vlan then the query will be tagged. Also
handle querier start/stop of vlan contexts.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helpers which check if the current bridge/port multicast context
should be used (i.e. they're not disabled) and use them for Rx IGMP/MLD
processing, timers and new group addition. It is important for vlans to
disable processing of timer/packet after the multicast_lock is obtained
if the vlan context doesn't have BR_VLFLAG_MCAST_ENABLED. There are two
cases when that flag is missing:
- if the vlan is getting destroyed it will be removed and timers will
be stopped
- if the vlan mcast snooping is being disabled
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to use the new port group to port context helper in places where
we cannot pass down the proper context (i.e. functions that can be
called by timers or outside the packet snooping paths).
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add br_multicast_pg_to_port_ctx() which returns the proper port multicast
context from either port or vlan based on bridge option and vlan flags.
As the comment inside explains the locking is a bit tricky, we rely on
the fact that BR_VLFLAG_MCAST_ENABLED requires multicast_lock to change
and we also require it to be held to call that helper. If we find the
vlan under rcu and it still has the flag then we can be sure it will be
alive until we unlock multicast_lock which should be enough.
Note that the context might change from vlan to bridge between different
calls to this helper as the mcast vlan knob requires only rtnl so it should
be used carefully and for read-only/check purposes.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a global knob that controls if vlan multicast snooping is enabled.
The proper contexts (vlan or bridge-wide) will be chosen based on the knob
when processing packets and changing bridge device state. Note that
vlans have their individual mcast snooping enabled by default, but this
knob is needed to turn on bridge vlan snooping. It is disabled by
default. To enable the knob vlan filtering must also be enabled, it
doesn't make sense to have vlan mcast snooping without vlan filtering
since that would lead to inconsistencies. Disabling vlan filtering will
also automatically disable vlan mcast snooping.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helpers to enable/disable vlan multicast based on its flags, we need
two flags because we need to know if the vlan has multicast enabled
globally (user-controlled) and if it has it enabled on the specific device
(bridge or port). The new private vlan flags are:
- BR_VLFLAG_MCAST_ENABLED: locally enabled multicast on the device, used
when removing a vlan, toggling vlan mcast snooping and controlling
single vlan (kernel-controlled, valid under RTNL and multicast_lock)
- BR_VLFLAG_GLOBAL_MCAST_ENABLED: globally enabled multicast for the
vlan, used to control the bridge-wide vlan mcast snooping for a
single vlan (user-controlled, can be checked under any context)
Bridge vlan contexts are created with multicast snooping enabled by
default to be in line with the current bridge snooping defaults. In
order to actually activate per vlan snooping and context usage a
bridge-wide knob will be added later which will default to disabled.
If that knob is enabled then automatically all vlan snooping will be
enabled. All vlan contexts are initialized with the current bridge
multicast context defaults.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add global and per-port vlan multicast context, only initialized but
still not used. No functional changes intended.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass multicast context pointers to multicast functions instead of bridge/port.
This would make it easier later to switch these contexts to their per-vlan
versions. The patch is basically search and replace, no functional changes.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out the bridge's global multicast context into a separate
structure which will later be used for per-vlan global context.
No functional changes intended.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out the port's multicast context into a separate structure which
will later be shared for per-port,vlan context. No functional changes
intended. We need the structure even if bridge multicast is not defined
to pass down as pointer to forwarding functions.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an MRD advertisement is received on a bridge port with multicast
snooping enabled, we mark it as a router port automatically, that
includes adding that port to the router port list. The multicast lock
protects that list, but it is not acquired in the MRD advertisement case
leading to a race condition, we need to take it to fix the race.
Cc: stable@vger.kernel.org
Cc: linus.luessing@c0d3.blue
Fixes: 4b3087c7e3 ("bridge: Snoop Multicast Router Advertisements")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a PIM hello packet is received on a bridge port with multicast
snooping enabled, we mark it as a router port automatically, that
includes adding that port the router port list. The multicast lock
protects that list, but it is not acquired in the PIM message case
leading to a race condition, we need to take it to fix the race.
Cc: stable@vger.kernel.org
Fixes: 91b02d3d13 ("bridge: mcast: add router port on PIM hello message")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The br_ip6_multicast_add_router() prototype is defined only when
CONFIG_IPV6 is enabled, but the function is always referenced, so there
is this build error with CONFIG_IPV6 not defined:
net/bridge/br_multicast.c: In function ‘__br_multicast_enable_port’:
net/bridge/br_multicast.c:1743:3: error: implicit declaration of function ‘br_ip6_multicast_add_router’; did you mean ‘br_ip4_multicast_add_router’? [-Werror=implicit-function-declaration]
1743 | br_ip6_multicast_add_router(br, port);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~
| br_ip4_multicast_add_router
net/bridge/br_multicast.c: At top level:
net/bridge/br_multicast.c:2804:13: warning: conflicting types for ‘br_ip6_multicast_add_router’
2804 | static void br_ip6_multicast_add_router(struct net_bridge *br,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~
net/bridge/br_multicast.c:2804:13: error: static declaration of ‘br_ip6_multicast_add_router’ follows non-static declaration
net/bridge/br_multicast.c:1743:3: note: previous implicit declaration of ‘br_ip6_multicast_add_router’ was here
1743 | br_ip6_multicast_add_router(br, port);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~
Fix this build error by moving the definition out of the #ifdef.
Fixes: a3c02e769e ("net: bridge: mcast: split multicast router state for IPv4 and IPv6")
Signed-off-by: Matteo Croce <mcroce@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To properly support routable multicast addresses in batman-adv in a
group-aware way, a batman-adv node needs to know if it serves multicast
routers.
This adds a function to the bridge to export this so that batman-adv
can then make full use of the Multicast Router Discovery capability of
the bridge.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
A multicast router for IPv4 does not imply that the same host also is a
multicast router for IPv6 and vice versa.
To reduce multicast traffic when a host is only a multicast router for
one of these two protocol families, keep router state for IPv4 and IPv6
separately. Similar to how querier state is kept separately.
For backwards compatibility for netlink and switchdev notifications
these two will still only notify if a port switched from either no
IPv4/IPv6 multicast router to any IPv4/IPv6 multicast router or the
other way round. However a full netlink MDB router dump will now also
include a multicast router timeout for both IPv4 and IPv6.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for the upcoming split of multicast router state into
their IPv4 and IPv6 variants split router port deletion and notification
into two functions. When we disable a port for instance later we want to
only send one notification to switchdev and netlink for compatibility
and want to avoid sending one for IPv4 and one for IPv6. For that the
split is needed.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for the upcoming split of multicast router state into
their IPv4 and IPv6 variants move the protocol specific router list
and timer access to ip4 wrapper functions.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for the upcoming split of multicast router state into
their IPv4 and IPv6 variants move the protocol specific timer access to
an ip4 wrapper function.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for the upcoming split of multicast router state into
their IPv4 and IPv6 variants make br_multicast_is_router() protocol
family aware.
Note that for now br_ip6_multicast_is_router() uses the currently still
common ip4_mc_router_timer for now. It will be renamed to
ip6_mc_router_timer later when the split is performed.
While at it also renames the "1" and "2" constants in
br_multicast_is_router() to the MDB_RTR_TYPE_TEMP_QUERY and
MDB_RTR_TYPE_PERM enums.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for the upcoming split of multicast router state into
their IPv4 and IPv6 variants and as the br_multicast_mark_router() will
be split for that remove the select querier wrapper and instead add
ip4 and ip6 variants for br_multicast_query_received().
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for the upcoming split of multicast router state into
their IPv4 and IPv6 variants, rename the affected variable to the IPv4
version first to avoid some renames in later commits.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IPv6 Multicast Router Advertisements parsing has the following two
issues:
For one thing, ICMPv6 MRD Advertisements are smaller than ICMPv6 MLD
messages (ICMPv6 MRD Adv.: 8 bytes vs. ICMPv6 MLDv1/2: >= 24 bytes,
assuming MLDv2 Reports with at least one multicast address entry).
When ipv6_mc_check_mld_msg() tries to parse an Multicast Router
Advertisement its MLD length check will fail - and it will wrongly
return -EINVAL, even if we have a valid MRD Advertisement. With the
returned -EINVAL the bridge code will assume a broken packet and will
wrongly discard it, potentially leading to multicast packet loss towards
multicast routers.
The second issue is the MRD header parsing in
br_ip6_multicast_mrd_rcv(): It wrongly checks for an ICMPv6 header
immediately after the IPv6 header (IPv6 next header type). However
according to RFC4286, section 2 all MRD messages contain a Router Alert
option (just like MLD). So instead there is an IPv6 Hop-by-Hop option
for the Router Alert between the IPv6 and ICMPv6 header, again leading
to the bridge wrongly discarding Multicast Router Advertisements.
To fix these two issues, introduce a new return value -ENODATA to
ipv6_mc_check_mld() to indicate a valid ICMPv6 packet with a hop-by-hop
option which is not an MLD but potentially an MRD packet. This also
simplifies further parsing in the bridge code, as ipv6_mc_check_mld()
already fully checks the ICMPv6 header and hop-by-hop option.
These issues were found and fixed with the help of the mrdisc tool
(https://github.com/troglobit/mrdisc).
Fixes: 4b3087c7e3 ("bridge: Snoop Multicast Router Advertisements")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_NET_SWITCHDEV is disabled, the shim for switchdev_port_attr_set
inside br_mc_disabled_update returns -EOPNOTSUPP. This is not caught,
and propagated to the caller of br_multicast_add_port, preventing ports
from joining the bridge.
Reported-by: Christian Borntraeger <borntraeger@de.ibm.com>
Fixes: ae1ea84b33 ("net: bridge: propagate error code and extack from br_mc_disabled_update")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Oleksandr Mazur