Add sanity checks on "addr" input parameter in dw_pcie_cfg_read() and
dw_pcie_cfg_write(). These checks make sure that accesses are aligned on
their size, e.g., a 4-byte config access is aligned on a 4-byte boundary.
[bhelgaas: changelog, set *val = 0 in failure case]
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
Callers of dw_pcie_cfg_read() and dw_pcie_cfg_write() previously had to
split the address into "addr" and "where". The callees assumed "addr" was
32-bit aligned (with zeros in the low two bits) and they used only the low
two bits of "where".
Accept the entire address in "addr" and drop the now-redundant "where"
argument. As an example, this replaces this:
int dw_pcie_cfg_read(void __iomem *addr, int where, int size, u32 *val)
*val = readb(addr + (where & 1));
with this:
int dw_pcie_cfg_read(void __iomem *addr, int size, u32 *val)
*val = readb(addr):
[bhelgaas: changelog, split access size change to separate patch]
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
dw_pcie_cfg_write() uses the exact 8-, 16-, or 32-bit access size
requested, but dw_pcie_cfg_read() previously performed a 32-bit read and
masked out the bits requested.
Use the exact access size in dw_pcie_cfg_read(). For example, if we want
an 8-bit read, use readb() instead of using readl() and masking out the 8
bits we need. This makes it symmetric with dw_pcie_cfg_write().
[bhelgaas: split into separate patch, set *val = 0 in failure case]
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Set up the high part of the MSI target address to allow the MSI target to
be above 4GB on 64bit and PAE systems.
[bhelgaas: changelog]
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
Implement multivector MSI IRQ setup. This allows to set up and use multiple
MSI IRQs per device.
[bhelgaas: changelog, use -EINVAL instead of -ENOSYS]
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
Factor out the PCI MSI message setup from the single MSI setup function.
This will be reused by the multivector MSI setup.
No functional change yet.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
The value under PORT_LOGIC_LINK_WIDTH_MASK is 0x1, 0x2, 0x4, 0x8. In IP
v4.2, bits [16:8] are defined for NUM_OF_LANES. But in IP v4.4, bits[12:8]
are defined for NUM_OF_LANES, bits [16:13] are for other usages (bit 16 is
AUTO_LANE_FLIP_CTRL_EN, bits [15:13] are PRE_DET_LANE).
As there is no conflict about NUM_OF_LANES between v4.2 and v4.4, change
the mask value to avoid future problems.
Signed-off-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Pull irq updates from Thomas Gleixner:
"This updated pull request does not contain the last few GIC related
patches which were reported to cause a regression. There is a fix
available, but I let it breed for a couple of days first.
The irq departement provides:
- new infrastructure to support non PCI based MSI interrupts
- a couple of new irq chip drivers
- the usual pile of fixlets and updates to irq chip drivers
- preparatory changes for removal of the irq argument from interrupt
flow handlers
- preparatory changes to remove IRQF_VALID"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (129 commits)
irqchip/imx-gpcv2: IMX GPCv2 driver for wakeup sources
irqchip: Add bcm2836 interrupt controller for Raspberry Pi 2
irqchip: Add documentation for the bcm2836 interrupt controller
irqchip/bcm2835: Add support for being used as a second level controller
irqchip/bcm2835: Refactor handle_IRQ() calls out of MAKE_HWIRQ
PCI: xilinx: Fix typo in function name
irqchip/gic: Ensure gic_cpu_if_up/down() programs correct GIC instance
irqchip/gic: Only allow the primary GIC to set the CPU map
PCI/MSI: pci-xgene-msi: Consolidate chained IRQ handler install/remove
unicore32/irq: Prepare puv3_gpio_handler for irq argument removal
tile/pci_gx: Prepare trio_handle_level_irq for irq argument removal
m68k/irq: Prepare irq handlers for irq argument removal
C6X/megamode-pic: Prepare megamod_irq_cascade for irq argument removal
blackfin: Prepare irq handlers for irq argument removal
arc/irq: Prepare idu_cascade_isr for irq argument removal
sparc/irq: Use access helper irq_data_get_affinity_mask()
sparc/irq: Use helper irq_data_get_irq_handler_data()
parisc/irq: Use access helper irq_data_get_affinity_mask()
mn10300/irq: Use access helper irq_data_get_affinity_mask()
irqchip/i8259: Prepare i8259_irq_dispatch for irq argument removal
...
ARM previously stored the msi_controller pointer in its sysdata, struct
pci_sys_data, and implemented pcibios_msi_controller() to retrieve it.
That made PCI host controller drivers specific to ARM because they had to
put the msi_controller pointer in the ARM-specific pci_sys_data.
There is now a generic mechanism, pci_scan_root_bus_msi(), for giving the
msi_controller pointer to the PCI core. Use this for all ARM systems and
for the DesignWare and Xilinx PCI host controller drivers.
This removes an ARM dependency from the DesignWare, DRA7xx, EXYNOS, i.MX6,
Keystone, Layerscape, SPEAr13xx, and Xilinx drivers.
[bhelgaas: changelog, split into separate patch]
Suggested-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
CC: Pratyush Anand <pratyush.anand@gmail.com>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Simon Horman <horms@verge.net.au>
CC: Russell King <linux@arm.linux.org.uk>
CC: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
CC: Thierry Reding <thierry.reding@gmail.com>
CC: Michal Simek <michal.simek@xilinx.com>
CC: Marc Zyngier <marc.zyngier@arm.com>
* pci/hotplug:
PCI: pciehp: Remove ignored MRL sensor interrupt events
PCI: pciehp: Remove unused interrupt events
PCI: pciehp: Handle invalid data when reading from non-existent devices
PCI: Hold pci_slot_mutex while searching bus->slots list
PCI: Protect pci_bus->slots with pci_slot_mutex, not pci_bus_sem
PCI: pciehp: Simplify pcie_poll_cmd()
PCI: Use "slot" and "pci_slot" for struct hotplug_slot and struct pci_slot
* pci/iommu:
PCI: Remove pci_ats_enabled()
PCI: Stop caching ATS Invalidate Queue Depth
PCI: Move ATS declarations to linux/pci.h so they're all together
PCI: Clean up ATS error handling
PCI: Use pci_physfn() rather than looking up physfn by hand
PCI: Inline the ATS setup code into pci_ats_init()
PCI: Rationalize pci_ats_queue_depth() error checking
PCI: Reduce size of ATS structure elements
PCI: Embed ATS info directly into struct pci_dev
PCI: Allocate ATS struct during enumeration
iommu/vt-d: Cache PCI ATS state and Invalidate Queue Depth
* pci/irq:
PCI: Kill off set_irq_flags() usage
* pci/virtualization:
PCI: Add ACS quirks for Intel I219-LM/V
set_irq_flags is ARM-specific with custom flags which have genirq
equivalents. Convert drivers to use the genirq interfaces directly, so we
can kill off set_irq_flags. The translation of flags is as follows:
IRQF_VALID -> !IRQ_NOREQUEST
IRQF_PROBE -> !IRQ_NOPROBE
IRQF_NOAUTOEN -> IRQ_NOAUTOEN
For IRQs managed by an irqdomain, the irqdomain core code handles clearing
and setting IRQ_NOREQUEST already, so there is no need to do this in .map()
functions, and we can simply remove the set_irq_flags calls. Some users
also modify IRQ_NOPROBE, and this has been maintained although it is not
clear that is really needed. There appears to be a great deal of blind
copy and paste of this code.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
CC: Kishon Vijay Abraham I <kishon@ti.com>
CC: Murali Karicheri <m-karicheri2@ti.com>
CC: Thierry Reding <thierry.reding@gmail.com>
CC: Stephen Warren <swarren@wwwdotorg.org>
CC: Alexandre Courbot <gnurou@gmail.com>
CC: Jingoo Han <jingoohan1@gmail.com>
CC: Pratyush Anand <pratyush.anand@gmail.com>
CC: Simon Horman <horms@verge.net.au>
CC: Michal Simek <michal.simek@xilinx.com>
CC: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Currently on Keystone SoCs, we always complain:
keystone-pcie 21021000.pcie: missing *config* reg space
Keystone uses an older version of DesignWare hardware that doesn't have
ATU support. So va_cfg0_base and va_cfg1_base are already set up in
ks_dw_pcie_host_init() before calling dw_pcie_host_init(), and they point
to the remote config space address va (both same for Keystone). Add a
check to avoid this boot noise on Keystone.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Rename irq_data_get_msi() as irq_data_get_msi_desc() to keep consistency
with other irq_data access helpers.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
After b97ea289cf ("PCI: Assign resources before drivers claim devices
(pci_scan_root_bus())"), pci_scan_root_bus() no longer adds the devices, so
it is equivalent to:
pci_create_root_bus()
pci_scan_child_bus()
Use pci_scan_root_bus() to simplify the code.
[bhelgaas: changelog]
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
CC: Mohit Kumar <mohit.kumar@st.com>
Most transactions' type are cfg0 and MEM, so the current iATU usage is not
balanced: iATU0 is hot while iATU1 is rarely used.
Refactor the iATU usage so we use iATU0 for cfg and IO and iATU1 for MEM.
This allocation idea comes from Minghuan Lian
<Minghuan.Lian@freescale.com>:
[bhelgaas: use link with Message-ID]
Link: http://lkml.kernel.org/r/1429091315-31891-3-git-send-email-Minghuan.Lian@freescale.com
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
Currently, the outbound iATU programming functions are similar: the only
difference is index, type, addr and size. Consolidate these functions into
one. This saves about 1700 bytes in text:
text data bss dec hex filename
9276 204 4 9484 250c pcie-designware.o-before
7532 204 4 7740 1e3c pcie-designware.o
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
Struct spear13xx_pcie_driver was in initdata, but we passed a pointer to it
to platform_driver_register(), which can use the pointer at arbitrary times
in the future, even after the initdata is freed. That leads to crashes.
Move spear13xx_pcie_driver and things referenced by it
(spear13xx_pcie_probe() and dw_pcie_host_init()) out of initdata.
[bhelgaas: changelog]
Fixes: 6675ef212d ("PCI: spear: Fix Section mismatch compilation warning for probe()")
Signed-off-by: Matwey V. Kornilov <matwey@sai.msu.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
CC: stable@vger.kernel.org # v3.17+
The DesignWare PCIe MSI hardware does not support MSI-X IRQs. Setting
those up failed as a side effect of a bug which was fixed by 91f8ae823f
("PCI: designware: Setup and clear exactly one MSI at a time").
Now that this bug is fixed, MSI-X IRQs need to be rejected explicitly;
otherwise devices trying to use them may end up with incorrectly working
interrupts.
Fixes: 91f8ae823f ("PCI: designware: Setup and clear exactly one MSI at a time")
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
CC: stable@vger.kernel.org # v3.18+
Most if not all ARM PCI host controller device drivers either ignore the
domain field in the pci_sys_data structure or just increment it every time
a host controller is probed, using it as a domain counter.
Therefore, instead of relying on pci_sys_data to stash the domain number in
a standard location, ARM pcibios code can be moved to the newly introduced
generic PCI domains code, implemented in commits:
41e5c0f81d ("of/pci: Add pci_get_new_domain_nr() and of_get_pci_domain_nr()")
670ba0c888 ("PCI: Add generic domain handling")
ARM code is made to select PCI_DOMAINS_GENERIC by default, which builds
core PCI code that assigns the domain number through the generic function:
void pci_bus_assign_domain_nr(...)
that relies on a DT property to define the domain number or falls back to a
counter according to a predefined logic; its usage replaces the current
domain assignment code in PCI host controllers present in the kernel.
Tested-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Yijing Wang <wangyijing@huawei.com>
Reviewed-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> # mvebu
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
CC: Mohit Kumar <mohit.kumar@st.com>
The PCI/MSI irq chip callbacks mask/unmask_msi_irq have been renamed
to pci_msi_mask/unmask_irq to mark them PCI specific. Rename all usage
sites. The conversion helper functions are kept around to avoid
conflicts in next and will be removed after merging into mainline.
Coccinelle assisted conversion. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: x86@kernel.org
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Mohit Kumar <mohit.kumar@st.com>
Cc: Simon Horman <horms@verge.net.au>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Yijing Wang <wangyijing@huawei.com>
Rename write_msi_msg() to pci_write_msi_msg() to mark it as PCI
specific.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Yingjoe Chen <yingjoe.chen@mediatek.com>
Cc: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Save MSI controller in pci_sys_data instead of assigning MSI controller
pointer to every PCI bus in .add_bus().
[bhelgaas: use dw_pcie_msi_chip, not dw_pcie_msi_controller]
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This patch fixes the following checkpatch warning:
WARNING: Missing a blank line after declarations
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
"msi_chip" isn't very descriptive, so rename it to "msi_controller". That
tells a little more about what it does and is already used in device tree
bindings.
No functional change.
[bhelgaas: changelog, change *only* the struct name so it's reviewable]
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Replace them by using the standard kernel bitmap ops. No functional
change, but makes the code a lot cleaner.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Pratyush Anand <pratyush.anand@st.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
The setup_irq function is supposed to set up exactly one MSI IRQ. Multiple
IRQ setup is handled differently, to respect the choices made by the upper
layers.
Also only clear one MSI IRQ at a time; the PCI core will call into this
function multiple times if it has to tear down more than one MSI IRQ.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Pratyush Anand <pratyush.anand@st.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Add a struct pcie_host_ops .get_msi_data() method for platforms to return
their special MSI message data.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Mohit KUMAR <mohit.kumar@st.com>
The struct pcie_host_ops .get_msi_data() method returns the MSI message
address. To accurately express its purpose, rename it to .get_msi_addr().
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Mohit KUMAR <mohit.kumar@st.com>
End address should be equal to start_addr + size - 1. Fix PCI IO resource
end address calculation.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Mohit KUMAR <mohit.kumar@st.com>
The code has calculated cfg0_base and cfg1_base when parsing 'reg' or
'ranges' property of PCI DTS node, so remove duplicate calculation. When
using 'reg', resource cfg is not used, so this code computed an incorrect
configuration base.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Mohit KUMAR <mohit.kumar@st.com>
of_get_address() expects pointers in the third and fourth parameters.
Pass NULL in order to fix the following sparse warnings:
drivers/pci/host/pcie-designware.c:433:51: warning: Using plain integer as NULL pointer
drivers/pci/host/pcie-designware.c:433:58: warning: Using plain integer as NULL pointer
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Jingoo Han <jg1.han@samsung.com>
The struct pcie_port_info doesn't contain any exclusive information
compared to other elements of struct pcie_port. So, keeping a separate
structure does not seem very logical. Therefore remove this struct and
embed its elements directly into struct pcie_port.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Mohit Kumar <mohit.kumar@st.com>
The driver had checks for this sprinkled all over. As we call
sys_to_pcie() before every instance of this check, we can move the
check to this single location to make things clear.
Removing the statements after BUG[_ON]() is safe as the kernel is halted at
this point anyway.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Mohit Kumar <mohit.kumar@st.com>
The pci_common_init_dev() call right before will already handle the device
resource allocation, so this call was a no-op.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Mohit Kumar <mohit.kumar@st.com>
Use pci_create_root_bus() similar to other PCI host controller drivers.
The main problem with pci_scan_root_bus() is that it not only creates the
root bus, but also activates all devices on the bus. This triggers PCI
device driver probe routines, which fail because resources haven't been
allocated.
To work around this we made sure that the host controller driver is probed
early and finishes resource allocation before any other device drivers are
registered. Switching to pci_create_root_bus() allows us to get rid of
this special handling.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Pratyush Anand <pratyush.anand@st.com>
Acked-by: Mohit Kumar <mohit.kumar@st.com>
This allows to explicitly specify the covered bus numbers in the
devicetree, which will come in handy once we see a SoC with more than one
PCIe host controller instance.
Previously the driver relied on the behavior of pci_scan_root_bus() to fill
in a range of 0x00-0xff if no valid range was found. We fall back to the
same range if no valid DT entry was found to keep backwards compatibility,
but now do it explicitly.
[bhelgaas: use %pR in error message to avoid duplication]
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Pratyush Anand <pratyush.anand@st.com>
Acked-by: Mohit Kumar <mohit.kumar@st.com>
The Keystone PCI controller is based on v3.65 DesignWare hardware. This
version differs from newer versions of the hardware in functional areas
discussed below that make it necessary to change dw_pcie_host_init() to
support v3.65 based PCI controller.
1. No support for ATU port. Any ATU-specific resource handling code is
to be bypassed for v3.65 h/w.
2. MSI controller uses application space to implement MSI and 32 MSI
interrupts are multiplexed over 8 IRQs to the host. Hence the code
to process MSI IRQ needs to be different. This patch allows
platform driver to provide its own irq_domain_ops ptr to
irq_domain_add_linear() through an API callback from the DesignWare
core driver.
3. MSI interrupt generation requires EP to write to the RC's
application register. So enhance the driver to allow setup of
inbound access to MSI IRQ register as a post scan bus API callback.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Pratyush Anand <pratyush.anand@st.com>
Acked-by: Mohit KUMAR <mohit.kumar@st.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
CC: Santosh Shilimkar <santosh.shilimkar@ti.com>
CC: Russell King <linux@arm.linux.org.uk>
CC: Grant Likely <grant.likely@linaro.org>
CC: Rob Herring <robh+dt@kernel.org>
CC: Jingoo Han <jg1.han@samsung.com>
CC: Richard Zhu <r65037@freescale.com>
CC: Kishon Vijay Abraham I <kishon@ti.com>
CC: Marek Vasut <marex@denx.de>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Pawel Moll <pawel.moll@arm.com>
CC: Mark Rutland <mark.rutland@arm.com>
CC: Ian Campbell <ijc+devicetree@hellion.org.uk>
CC: Kumar Gala <galak@codeaurora.org>
CC: Randy Dunlap <rdunlap@infradead.org>
CC: Grant Likely <grant.likely@linaro.org>
DesignWare v3.65 hardware implements MSI controller registers in
application space. This requires updates to the DesignWare core to
support controllers based on this older hardware.
Add msi_irq_set()/clear() interfaces to allow Set/Clear MSI IRQ enable bit
in the application register. Also, v3.65 hardware uses the MSI_IRQ
register in application register space to raise MSI IRQ to the RC from EP.
Current code uses the standard mechanism as per PCI spec. So add
get_msi_data() to get the address of this register so common code can
work on both v3.65 and newer hardware.
[bhelgaas: changelog]
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Pratyush Anand <pratyush.anand@st.com>
Acked-by: Mohit Kumar <mohit.kumar@st.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
CC: Russell King <linux@arm.linux.org.uk>
CC: Grant Likely <grant.likely@linaro.org>
CC: Rob Herring <robh+dt@kernel.org>
CC: Richard Zhu <r65037@freescale.com>
CC: Kishon Vijay Abraham I <kishon@ti.com>
CC: Marek Vasut <marex@denx.de>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Pawel Moll <pawel.moll@arm.com>
CC: Mark Rutland <mark.rutland@arm.com>
CC: Ian Campbell <ijc+devicetree@hellion.org.uk>
CC: Kumar Gala <galak@codeaurora.org>
CC: Randy Dunlap <rdunlap@infradead.org>
CC: Grant Likely <grant.likely@linaro.org>
DesignWare v3.65 hardware requires application space registers to be
configured to access the remote EP config space.
To support this, add rd_other_conf() and wr_other_conf() to pcie_host_ops.
[bhelgaas: changelog]
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Pratyush Anand <pratyush.anand@st.com>
Acked-by: Mohit Kumar <mohit.kumar@st.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
CC: Russell King <linux@arm.linux.org.uk>
CC: Grant Likely <grant.likely@linaro.org>
CC: Rob Herring <robh+dt@kernel.org>
CC: Richard Zhu <r65037@freescale.com>
CC: Kishon Vijay Abraham I <kishon@ti.com>
CC: Marek Vasut <marex@denx.de>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Pawel Moll <pawel.moll@arm.com>
CC: Mark Rutland <mark.rutland@arm.com>
CC: Ian Campbell <ijc+devicetree@hellion.org.uk>
CC: Kumar Gala <galak@codeaurora.org>
CC: Randy Dunlap <rdunlap@infradead.org>
CC: Grant Likely <grant.likely@linaro.org>
In DRA7, the CPU sees 32-bit addresses, but the PCIe controller can see
only 28-bit addresses. So whenever the CPU issues a read/write request,
the 4 most significant bits are used by L3 to determine the target
controller. For example, the CPU reserves [mem 0x20000000-0x2fffffff]
for the PCIe controller but the PCIe controller will see only
[0x00000000-0x0fffffff]. For programming the outbound translation
window the *base* should be programmed as 0x00000000. Whenever we try to
write to, e.g., 0x20000000, it will be translated to whatever we have
programmed in the translation window with base as 0x00000000.
This is needed when the dt node is modelled something like this:
axi {
compatible = "simple-bus";
#size-cells = <1>;
#address-cells = <1>;
ranges = <0x0 0x20000000 0x10000000 // 28-bit bus
0x51000000 0x51000000 0x3000>;
pcie@51000000 {
reg = <0x1000 0x2000>, <0x51002000 0x14c>, <0x51000000 0x2000>;
reg-names = "config", "ti_conf", "rc_dbics";
#address-cells = <3>;
#size-cells = <2>;
ranges = <0x81000000 0 0 0x03000 0 0x00010000
0x82000000 0 0x20013000 0x13000 0 0xffed000>;
};
};
Here the CPU address for configuration space is 0x20013000 and the
controller address for configuration space is 0x13000. The controller
address should be used while programming the ATU (in order for translation
to happen properly in DRA7xx).
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mohit Kumar <mohit.kumar@st.com>
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Arnd Bergmann <arnd@arndb.de>
The configuration address space has so far been specified in *ranges*,
however it should be specified in *reg* making it a platform MEM resource.
Hence used 'platform_get_resource_*' API to get configuration address space
in the designware driver.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Mohit Kumar <mohit.kumar@st.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Arnd Bergmann <arnd@arndb.de>
* pci/host-designware:
PCI: designware: Remove unnecessary use of 'conf_lock' spinlock
PCI: designware: Use new OF interrupt mapping when possible
PCI: designware: Fix iATU programming for cfg1, io and mem viewport
PCI: designware: Fix comment for setting number of lanes
* pci/host-imx6:
PCI: designware: Split Exynos and i.MX bindings
* pci/host-mvebu:
PCI: mvebu: Use '%pa' for printing 'phys_addr_t' type
PCI: mvebu: Remove unnecessary use of 'conf_lock' spinlock
PCI: mvebu: split PCIe BARs into multiple MBus windows when needed
bus: mvebu-mbus: allow several windows with the same target/attribute
bus: mvebu-mbus: Avoid setting an undefined window size
PCI: mvebu: fix off-by-one in the computed size of the mbus windows
* pci/host-tegra:
PCI: tegra: Use new OF interrupt mapping when possible
On i.MX6 the host controller MSI IRQ is shared with PCI legacy INTD. Make
sure we don't bail too early from the IRQ handler.
The issue is fairly theoretical as it would require a system setup with a
PCIe switch where one connected device is using legacy INTD and another one
using MSI, but better fix it now.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Richard Zhu <r65037@freescale.com>
Serialization of configuration accesses is provided by 'pci_lock' in
drivers/pci/access.c thus making the driver's 'conf_lock' superfluous.
Signed-off-by: Andrew Murray <amurray@embedded-bits.co.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Richard Zhu <r65037@freescale.com>
Gabriele Paoloni