* 'for-linus' of git://neil.brown.name/md:
md: Use revalidate_disk to effect changes in size of device.
md: allow raid5_quiesce to work properly when reshape is happening.
md/raid5: set reshape_position correctly when reshape starts.
md: Handle growth of v1.x metadata correctly.
md: avoid array overflow with bad v1.x metadata
md: when a level change reduces the number of devices, remove the excess.
md: Push down data integrity code to personalities.
md/raid6: release spare page at ->stop()
In cases of fragmented skb, with the data pointers being wrapped around
the TX buffer, the completion handling code would not forward the data
pointer and the firs fragment was unmapped several times, while others
were not unmapped at all.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
As revalidate_disk calls check_disk_size_change, it will cause
any capacity change of a gendisk to be propagated to the blockdev
inode. So use that instead of mucking about with locks and
i_size_write.
Also add a call to revalidate_disk in do_md_run and a few other places
where the gendisk capacity is changed.
Signed-off-by: NeilBrown <neilb@suse.de>
The ->quiesce method is not supposed to stop resync/recovery/reshape,
just normal IO.
But in raid5 we don't have a way to know which stripes are being
used for normal IO and which for resync etc, so we need to wait for
all stripes to be idle to be sure that all writes have completed.
However reshape keeps at least some stripe busy for an extended period
of time, so a call to raid5_quiesce can block for several seconds
needlessly.
So arrange for reshape etc to pause briefly while raid5_quiesce is
trying to quiesce the array so that the active_stripes count can
drop to zero.
Signed-off-by: NeilBrown <neilb@suse.de>
As the internal reshape_progress counter is the main driver
for reshape, the fact that reshape_position sometimes starts with the
wrong value has minimal effect. It is visible in sysfs and that
is all.
Signed-off-by: NeilBrown <neilb@suse.de>
The v1.x metadata does not have a fixed size and can grow
when devices are added.
If it grows enough to require an extra sector of storage,
we need to update the 'sb_size' to match.
Without this, md can write out an incomplete superblock with a
bad checksum, which will be rejected when trying to re-assemble
the array.
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
We trust the 'desc_nr' field in v1.x metadata enough to use it
as an index in an array. This isn't really safe.
So range-check the value first.
Signed-off-by: NeilBrown <neilb@suse.de>
When an array is changed from RAID6 to RAID5, fewer drives are
needed. So any device that is made superfluous by the level
conversion must be marked as not-active.
For the RAID6->RAID5 conversion, this will be a drive which only
has 'Q' blocks on it.
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
This patch replaces md_integrity_check() by two new public functions:
md_integrity_register() and md_integrity_add_rdev() which are both
personality-independent.
md_integrity_register() is called from the ->run and ->hot_remove
methods of all personalities that support data integrity. The
function iterates over the component devices of the array and
determines if all active devices are integrity capable and if their
profiles match. If this is the case, the common profile is registered
for the mddev via blk_integrity_register().
The second new function, md_integrity_add_rdev() is called from the
->hot_add_disk methods, i.e. whenever a new device is being added
to a raid array. If the new device does not support data integrity,
or has a profile different from the one already registered, data
integrity for the mddev is disabled.
For raid0 and linear, only the call to md_integrity_register() from
the ->run method is necessary.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
eeepc-laptop: fix hot-unplug on resume
ACPI: Ingore the memory block with zero block size in course of memory hotplug
ACPI: Don't treat generic error as ACPI error code in acpi memory hotplug driver
ACPI: bind workqueues to CPU 0 to avoid SMI corruption
ACPI: root-only read protection on /sys/firmware/acpi/tables/*
thinkpad-acpi: fix incorrect use of TPACPI_BRGHT_MODE_ECNVRAM
thinkpad-acpi: restrict procfs count value to sane upper limit
thinkpad-acpi: remove dock and bay subdrivers
thinkpad-acpi: disable broken bay and dock subdrivers
hp-wmi: check that an input device exists in resume handler
Revert "ACPICA: Remove obsolete acpi_os_validate_address interface"
Clearly, I am a glutton for punishment. I'll see if I can see Alan's
changes through to the end, otherwise I'll be fending off a lot of bug
reports for usb-serial devices.
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This function has traditionally used "insert_resource()", because before
commit cebd78a8c5 ("Fix pci_claim_resource") it used to just insert the
resource into whatever root resource tree that was indicated by
"pcibios_select_root()".
So there Matthew fixed it to actually look up the proper parent
resource, which means that now it's actively wrong to then traverse the
resource tree any more: we already know exactly where the new resource
should go.
And when we then did commit a76117dfd6 ("x86: Use pci_claim_resource"),
which changed the x86 PCI code from the open-coded
pr = pci_find_parent_resource(dev, r);
if (!pr || request_resource(pr, r) < 0) {
to using
if (pci_claim_resource(dev, idx) < 0) {
that "insert_resource()" now suddenly became a problem, and causes a
regression covered by
http://bugzilla.kernel.org/show_bug.cgi?id=13891
which this fixes.
Reported-and-tested-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Matthew Wilcox <willy@linux.intel.com>
Cc: Andrew Patterson <andrew.patterson@hp.com>
Cc: Linux PCI <linux-pci@vger.kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The size of receive buffer pointer was used to get size of
receive buffer instead of recvbuf_size itself, so only 4/8
bytes could be transfered.
This is a regression to 2.6.30 introduced by commit 8c90e11e35
mISDN: Use kernel_{send,recv}msg instead of open coding
Signed-off-by: Andreas Eversberg <andreas@eversberg.eu>
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the COH 901 327 found in U300 is clocked at 32 kHz we need
to wait for the interrupt clearing flag to propagate through
hardware in order not to accidentally fire off any interrupts
when we enable them.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
VLB support has been broken since at least 2004-2005 period as some
changes introduced back then assumed that ->pci_dev is always valid,
lets try to fix it:
- remove duplicated SET_NETDEV_DEV() call
- call SET_NETDEV_DEV() only for PCI devices
- check for ->pci_dev validity in pcnet32_open()
[ Alternatively we may consider removing VLB support but there would not
be much gain in it since an extra driver code needed for VLB support is
minimal and quite simple. ]
This takes care of the following entry from Dan's list:
drivers/net/pcnet32.c +1889 pcnet32_probe1(298) warning: variable derefenced before check 'pdev'
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Don Fry <pcnet32@verizon.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the debug printk() into the proper place and remove superfluous
NULL pointer check in pcnet32_probe1().
This takes care of the following entry from Dan's list:
drivers/net/pcnet32.c +1889 pcnet32_probe1(298) warning: variable derefenced before check 'pdev'
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Don Fry <pcnet32@verizon.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a path when an assetion in dev_unicast_sync() appears.
igmp6_group_added -> dev_mc_add -> __dev_set_rx_mode ->
-> vlan_dev_set_rx_mode -> dev_unicast_sync
Therefore we cannot protect this list with rtnl. This patch restores the
original protecting this list with spinlock.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Tested-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change default dma mask for NX3031 to 39 bit with ability
to update it to 64-bit (if firmware indicates support). Old
code was restricting it under 4GB (32-bit), sometimes causing
failure to allocate descriptor rings on heavily populated
system. NX2031 based NICs will still get 32-bit coherent mask.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check whether index is within bounds before testing the element.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check whether index is within bounds before testing the element.
In the last iteration i is PHY_MAX_ADDR. the condition
`!(p = pd->mii.bus->phy_map[PHY_MAX_ADDR])' is undefined and may
evaluate to false, which leads to a dereference of this invalid
phy_map in the phy_connect() below.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check whether index is within bounds before testing the element.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
memcpy() should take into account size of pointers,
not only number of pointers to copy.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Failure to call unregister_pernet_gen_device() can exhaust memory
if module is loaded/unloaded many times.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the corner cases where the sum of MTU of the free
channels (adjusted for fragmentation overheads) is less than the MTU
of PPP link. There are at least 3 situations where this case might
arise:
- some of the channels are busy
- the multilink session is running in a degraded state (i.e. with less
than its full complement of active channels)
- by design, where multilink protocol is being used to artificially
increase the effective link MTU of a single link.
Without this patch, at most 1 fragment is ever sent per free channel
for a given PPP frame and any remaining part of the PPP frame that
does not fit into those fragments is silently discarded.
This patch restores the original behaviour which was broken by commit
9c705260fe 'ppp:ppp_mp_explode()
redesign'. Once all 'free' channels have been given a fragment, an
additional fragment is queued to each available channel in turn, as many
times as necessary, until the entire PPP frame has been consumed.
Signed-off-by: Ben McKeegan <ben@netservers.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
OOPS on resume when the wireless adaptor is disabled during suspend was
introduced by "eeepc-laptop: read rfkill soft-blocked state on resume".
Unable to handle kernel NULL pointer dereference
Process s2disk
Tainted: G W
IP: klist_put
Call trace:
? klist_del
? device_del
? device_unregister
? pci_stop_dev
? pci_stop_bus
? pci_remove_device
? eeepc_rfkill_hotplug [eeepc_laptop]
? eeepc_hotk_resume [eeepc_laptop]
? acpi_device_resume
? device_resume
? hibernation_snapshot
It appears the PCI device is removed twice. The eeepc_rfkill_hotplug()
call from the resume handler is racing against the call from the ACPI
notifier callback. The ACPI notification is triggered by the resume
handler when it refreshes the value of CM_ASL_WLAN.
The fix is to serialize hotplug calls using a workqueue.
http://bugzilla.kernel.org/show_bug.cgi?id=13825
Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Acked-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
If the memory block size is zero, ignore it and don't do the memory hotplug
flowchart. Otherwise it will complain the following warning message:
>System RAM resource 0 - ffffffffffffffff cannot be added
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Don't treat the generic error as ACPI error code. Otherwise when the generic
code is returned, it will complain the following warning messag:
>ACPI Exception (acpi_memhotplug-0171): UNKNOWN_STATUS_CODE,
Cannot get acpi bus device [20080609]
>ACPI: Cannot find driver data
> ACPI Error (utglobal-0127): Unknown exception code: 0xFFFFFFED [20080609]
> Pid: 85, comm: kacpi_notify Not tainted 2.6.27.19-5-default #1
Call Trace:
[<ffffffff8020da29>] show_trace_log_lvl+0x41/0x58
[<ffffffff8049a3da>] dump_stack+0x69/0x6f
.....
At the same time when the generic error code is returned, the ACPI_EXCEPTION
is replaced by the printk.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
On some machines, a software-initiated SMI causes corruption unless the
SMI runs on CPU 0. An SMI can be initiated by any AML, but typically it's
done in GPE-related methods that are run via workqueues, so we can avoid
the known corruption cases by binding the workqueues to CPU 0.
References:
http://bugzilla.kernel.org/show_bug.cgi?id=13751https://bugs.launchpad.net/bugs/157171https://bugs.launchpad.net/bugs/157691
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fix those warnings:
drivers/parisc/hppb.c: In function 'hppb_probe':
drivers/parisc/hppb.c:65: warning: format '%x' expects type 'unsigned int', but argument 2 has type 'resource_size_t'
drivers/parisc/hppb.c:77: warning: format '%08x' expects type 'unsigned int', but argument 3 has type 'resource_size_t'
drivers/parisc/hppb.c:77: warning: format '%08x' expects type 'unsigned int', but argument 4 has type 'resource_size_t'
Signed-off-by: Helge Deller <deller@gmx.de>
Fix those compiler warnings, which indeed point to a bug:
drivers/char/agp/parisc-agp.c:228: warning: initialization from incompatible pointer type
drivers/char/agp/parisc-agp.c:201: warning: 'parisc_agp_page_mask_memory' defined but not used
Signed-off-by: Helge Deller <deller@gmx.de>
This adds a missing unlock of nilfs->ns_writer_mutex in
nilfs_mdt_write_page() function.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Background:
Several race conditions in the scheduler have cropped up
recently, which Steven and I have tracked down using ftrace.
The most recent one turns out to be a race in how the scheduler
determines a suitable migration target for RT tasks, introduced
recently with commit:
commit 68e74568fb
Date: Tue Nov 25 02:35:13 2008 +1030
sched: convert struct cpupri_vec cpumask_var_t.
The original design of cpupri allowed lockless readers to
quickly determine a best-estimate target. Races between the
pri_active bitmap and the vec->mask were handled in the
original code because we would detect and return "0" when this
occured. The design was predicated on the *effective*
atomicity (*) of caching the result of cpus_and() between the
cpus_allowed and the vec->mask.
Commit 68e74568 changed the behavior such that vec->mask is
accessed multiple times. This introduces a subtle race, the
result of which means we can have a result that returns "1",
but with an empty bitmap.
*) yes, we know cpus_and() is not a locked operator across the
entire composite array, but it is implicitly atomic on a
per-word basis which is all the design required to work.
Implementation:
Rather than forgoing the lockless design, or reverting to a
stack-based cpumask_t, we simply check for when the race has
been encountered and continue processing in the event that the
race is hit. This renders the removal race as if the priority
bit had been atomically cleared as well, and allows the
algorithm to execute correctly.
Signed-off-by: Gregory Haskins <ghaskins@novell.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <20090730145728.25226.92769.stgit@dev.haskins.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The latencytop and sleep accounting code assumes that any
scheduler entity represents a task, this is not so.
Cc: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We skip the display of idle routine related symbols because
they are typically rather erratic and confusing: they depend
on the IRQ rate or sometimes they dominate the profile if
they are polling based.
Add mwait_idle_with_hints too, this is one of the idle
routines on x86.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch fixes a spelling error that has resulted from copy
and pasting. The location of the error was found using a
semantic patch but the semantic patch was not trying to find
these errors. After looking things over it seemed logical that
this change was needed. Please review it and then include the
patch if it is in fact the correct change.
Signed-off-by: Stoyan Gaydarov <sgayda2@uiuc.edu>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <1248949529-20891-1-git-send-email-sgayda2@uiuc.edu>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Since FORK is now also issued for threads, detect those by
comparing the parent and child PID.
Teach it about EXIT events and ignore them.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In order to be able to distinguish between no samples due to
inactivity and no samples due to task ended, Arjan asked for
PERF_EVENT_EXIT events. This is useful to the boot delay
instrumentation (bootchart) app.
This patch changes the PERF_EVENT_FORK to be emitted on every
clone, and adds PERF_EVENT_EXIT to be emitted on task exit,
after the task's counters have been closed.
This task tracing is controlled through: attr.comm || attr.mmap
and through the new attr.task field.
Suggested-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Anton Blanchard <anton@samba.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
[ cleaned up perf_counter.h a bit ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Currently the counter value returned by read() is the value of
the parent counter, to which child counters are only fed back
on child exit.
Thus read() can return rather erratic (and meaningless) numbers
depending on the state of the child processes.
Change this by always iterating the full child hierarchy on
read() and sum all counters.
Suggested-by: Corey Ashford <cjashfor@linux.vnet.ibm.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Linus Torvalds