According to the R-Car Gen3 Hardware Manual Errata for Rev 1.50 of Feb
12, 2019, the sel_ndfc MOD_SEL register bit is renamed to sel_ndf.
Update the pin control drivers to reflect this.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Update R-Car E3]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
According to the R-Car Gen3 Hardware Manual Errata for Rev 1.50 of
Feb 12, 2019, the RTS{0,1,3,4}_#/TANS pin names defined in the GPSR and
IPSR registers are renamed to RTS{0,1,3,4}_#.
This patch updates the pin control drivers to reflect this.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Update R-Car H3 ES1.x, V3M, V3H, and D3]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
According to the R-Car Gen3 Hardware Manual Errata for Rev 1.00 of Aug
24, 2018, there is no need to configure MOD_SEL1 bit30 when the
SSI_SCK2_{A,B} or SSI_WS2_{A,B} pin functions are selected.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Remove now unused definitions, mark MOD_SEL1 bit30 reserved]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
According to the R-Car Gen3 Hardware Manual Errata for Rev 1.00 of
Aug 24, 2018, there is no need to configure MOD_SEL1 bit31 when the
SIM0_D_{A,B} pin function is selected.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Remove now unused definitions, mark MOD_SEL1 bit31 reserved]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
According to the R-Car Gen3 Hardware Manual Errata for Rev 1.00 of Aug
24, 2018, the MOD_SEL0 bit16 must be set to 0 when the NFALE_A and
NFRB_N_A pin functions are selected.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Currently the PINMUX_CFG_REG_VAR() macro must be followed by
initialization data, specifying all enum IDs. Hence the macro itself
does not know anything about the enum IDs, preventing the macro from
performing any validation on it.
Make the macro accept the enum IDs as a parameter, and update all users.
Note that array data enclosed by curly braces cannot be passed to a
macro as a parameter, hence both the register field widths and the enum
IDs are wrapped using the GROUP() macro.
No functional changes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Currently the PINMUX_CFG_REG() macro must be followed by initialization
data, specifying all enum IDs. Hence the macro itself does not know
anything about the enum IDs, preventing the macro from performing any
validation on it.
Make the macro accept the enum IDs as a parameter, and update all users.
Note that array data enclosed by curly braces cannot be passed to a
macro as a parameter, hence the enum IDs are wrapped using a new macro
GROUPS().
No functional changes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Source files using -Exxx error codes should include <linux/errno.h>.
On ARM, this header file is included indirectly; on SuperH, it is not,
leading to "error: ‘EINVAL’ undeclared" failures when enabling
compile-testing later.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The TDSELCTRL register is responsible for configuring the SDHI/MMC clock
return path delay and may be adjusted by the bootloader. Retain the value
across suspend/resume to prevent hardware instability after resume.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
CANFD is found also on the R8A774C0, therefore move CANFD pin
groups and functions to "common".
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The R-Car Gen3 HardWare Manual Errata for Rev. 1.00 (Jul 2, 2018)
renamed the various miscellaneous I/O control registers (IOCTRLx) on
R-Car E3, to reflect better their actual purposes, and matching other
SoCs.
Update the code to match this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
This patch adds DRIF{0,1,2,3} pins, groups and functions to the R8A77990
SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds TMU TCLK{1,2} pins, groups and functions to
the R8A77990 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This reverts commit f4caa6ee73.
The same can be expressed better by dropping the
SH_PFC_PIN_CFG_PULL_DOWN flag from the GPIO description, as it includes
returning an error to the caller when trying to configure the pin for
pull-down, causing:
sh-pfc e6060000.pin-controller: pin_config_set op failed for pin 201
sh-pfc e6060000.pin-controller: Error applying setting, reverse things back
sh-pfc e6060000.pin-controller: failed to select default state
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
MOD_SEL register bit numbering was different from R-Car E3 SoC and
R-Car H3/M3-[WN] SoCs.
MOD_SEL 1-bit H3/M3-[WN] E3
=============== ========== =====
Set Value = H'0 b'0 b'0
Set Value = H'1 b'1 b'1
MOD_SEL 2-bits H3/M3-[WN] E3
=============== ========== =====
Set Value = H'0 b'00 b'00
Set Value = H'1 b'01 b'10
Set Value = H'2 b'10 b'01
Set Value = H'3 b'11 b'11
MOD_SEL 3-bits H3/M3-[WN] E3
=============== ========== =====
Set Value = H'0 b'000 b'000
Set Value = H'1 b'001 b'100
Set Value = H'2 b'010 b'010
Set Value = H'3 b'011 b'110
Set Value = H'4 b'100 b'001
Set Value = H'5 b'101 b'101
Set Value = H'6 b'110 b'011
Set Value = H'7 b'111 b'111
This patch replaces the #define name and value of MOD_SEL.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Fixes: 6d4036a1e3 ("pinctrl: sh-pfc: Initial R8A77990 PFC support")
[shimoda: Split a patch per SoC and revise the commit log]
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
[geert: Use macros to do the actual reordering]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
According to the R-Car Gen3 Hardware Manual Errata for Rev 1.00 of
Aug 24, 2018, the MOD_SEL0 bit2 is set when RX2_{A,B}, TX2_{A,B} and
SCK2_A pin functions are selected.
Fixes: 6d4036a1e3 ("pinctrl: sh-pfc: Initial R8A77990 PFC support")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
According to the R-Car Gen3 Hardware Manual Errata for Rev 1.00 of
Aug 24, 2018, the MOD_SEL0 bit3 is set to 0 when TX0_A pin function is
selected, and the MOD_SEL0 bit3 is set to 1 when TX0_B pin function is
selected.
Fixes: 6d4036a1e3 ("pinctrl: sh-pfc: Initial R8A77990 PFC support")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The SEL_I2C1 (MOD_SEL0[21:20]) field in Module Select Register 0 has a
width of 2 bits, i.e. it allows programming one out of 4 different
configurations.
However, the MOD_SEL0_21_20 macro contains 8 values instead of 4,
overflowing into the subsequent fields in the register, and thus breaking
the configuration of the latter.
Fix this by dropping the bogus last 4 values, including the non-existent
SEL_I2C1_4 configuration.
Fixes: 6d4036a1e3 ("pinctrl: sh-pfc: Initial R8A77990 PFC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Due to an interaction with commit 9f2b76a2db ("pinctrl: sh-pfc:
r8a77990: Add R8A774C0 PFC support"), the state of the I/O Control
Registers is saved/restored during s2ram on RZ/G2E, but not on R-Car E3.
Hence on R-Car E3, SDHI voltage state is lost after system resume.
Fix this by registering the I/O Control Registers on R-Car E3, too.
Fixes: 33847a7137 ("pinctrl: sh-pfc: r8a77990: Add voltage switch operations for SDHI")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The R-Car Gen3 HardWare Manual Errata for Rev. 1.00 (Jul 2, 2018) states
that the USB30_OVC pin supports pull-up only. It has a bit assigned in
the pull-enable register (PUEN5), but not in the pull-up/down control
register (PUD5).
Add a check for this, to prevent configuring a prohibited setting.
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Fixes: 83f6941a42 ("pinctrl: sh-pfc: r8a77990: Add bias pinconf support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds CAN FD{0,1} pins, groups and functions to the R8A77990
SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
[geert: Move canfd from common to automotive]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds CAN{0,1} pins, groups and functions to the R8A77990 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds HSCIF{0,1,2,3,4} pins, groups and functions to
the R8A77990 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add pin, mux and functions definitions for VIN4 and VIN5 for R-Car E3.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch supports the {get,set}_io_voltage operations of SDHI.
This operates the IOCTRL30 register on the R8A77990 SoC and makes
1.8V/3.3V signal voltage switch possible.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds SDHI{0,1,3} pins, groups and functions to the R8A77990
SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds Audio SSI{0,1,2,3,4,5,6,7,8,9} pins, groups
and functions to the R8A77990 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[simon: rebase]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds AUDIO_CLK{A,B,C}, AUDIO_CLKOUT, AUDIO_CLKOUT{1,2,3}
pins, groups and functions to the R8A77990 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[simon: rebase]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add pins, groups, and function for the Interrupt Controller for
External Devices (INTC-EX) on the R-Car E3 SoC.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Renesas RZ/G SoCs are pin compatible with R-Car SoCs, but lack several
automotive-specific peripherals.
Currently pin groups and functions for automotive-specific peripherals
are grouped in arrays named after the automative SoC part numbers.
Rename them to "automotive" for clarity and consistency.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Renesas RZ/G2E (a.k.a. r8a774c0) is pin compatible with R-Car
E3 (a.k.a. r8a77990), however it doesn't have several automotive
specific peripherals. Add a r8a77990 specific pin groups/functions
along with common pin groups/functions for supporting both r8a77990
and r8a774c0 SoCs.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds MSIOF{0,1,2,3} pins, groups and functions to
the R8A77990 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds DU pins, groups and function for the R8A77990 (E3) SoC.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds PWM{0,1,2,3,4,5,6} pins, groups and functions to
the R8A77990 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds USB30_{PWEN,OVC} and USB3HS0_ID pins, groups and functions
to the R8A77990 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds USB0_{PWEN,OVC}_{A,B} and USB0_ID pins, groups and
functions to the R8A77990 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since the datasheet Rev.1.00 has an error about the USB ID pin name,
this patch revises it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds group and function of AVB PHY, LINK, MAGIC, MII and PTP
pins for the R8A77990 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds I2C{1,2,4,5,6,7} pins, groups and functions to
the R8A77990 SoC.
NOTE: I2C0 and I2C3 are not pin multiplexed.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch implements control of pull-up and pull-down. On this SoC there
is no simple mapping of GP pins to bias register bits, so we need a table.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds initial pinctrl driver to support for the R8A77990 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Takeshi Kihara