Pull irq fixes from Thomas Glexiner:
- unbreak the irq trigger type check for legacy platforms
- a handful fixes for ARM GIC v3/4 interrupt controllers
- a few trivial fixes all over the place
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq/matrix: Make - vs ?: Precedence explicit
irqchip/imgpdc: Use resource_size function on resource object
irqchip/qcom: Fix u32 comparison with value less than zero
irqchip/exiu: Fix return value check in exiu_init()
irqchip/gic-v3-its: Remove artificial dependency on PCI
irqchip/gic-v4: Add forward definition of struct irq_domain_ops
irqchip/gic-v3: pr_err() strings should end with newlines
irqchip/s3c24xx: pr_err() strings should end with newlines
irqchip/gic-v3: Fix ppi-partitions lookup
irqchip/gic-v4: Clear IRQ_DISABLE_UNLAZY again if mapping fails
genirq: Track whether the trigger type has been set
Most of the commits are for defconfig changes, to enable newly added
drivers or features that people have started using. For the changed
lines lines, we have mostly cleanups, the affected platforms are
OMAP, Versatile, EP93xx, Samsung, Broadcom, i.MX, and Actions.
The largest single change is the introduction of the TI "sysc" bus
driver, with the intention of cleaning up more legacy code.
Two new SoC platforms get added this time:
- Allwinner R40 is a modernized version of the A20 chip, now
with a Quad-Core ARM Cortex-A7. According to the manufacturer,
it is intended for "Smart Hardware"
- Broadcom Hurricane 2 (Aka Strataconnect BCM5334X) is a family
of chips meant for managed gigabit ethernet switches, based
around a Cortex-A9 CPU.
Finally, we gain SMP support for two platforms: Renesas R-Car E2
and Amlogic Meson8/8b, which were previously added but only supported
uniprocessor operation.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jlJ2
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"Most of the commits are for defconfig changes, to enable newly added
drivers or features that people have started using. For the changed
lines lines, we have mostly cleanups, the affected platforms are OMAP,
Versatile, EP93xx, Samsung, Broadcom, i.MX, and Actions.
The largest single change is the introduction of the TI "sysc" bus
driver, with the intention of cleaning up more legacy code.
Two new SoC platforms get added this time:
- Allwinner R40 is a modernized version of the A20 chip, now with a
Quad-Core ARM Cortex-A7. According to the manufacturer, it is
intended for "Smart Hardware"
- Broadcom Hurricane 2 (Aka Strataconnect BCM5334X) is a family of
chips meant for managed gigabit ethernet switches, based around a
Cortex-A9 CPU.
Finally, we gain SMP support for two platforms: Renesas R-Car E2 and
Amlogic Meson8/8b, which were previously added but only supported
uniprocessor operation"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (118 commits)
ARM: multi_v7_defconfig: Select RPMSG_VIRTIO as module
ARM: multi_v7_defconfig: enable CONFIG_GPIO_UNIPHIER
arm64: defconfig: enable CONFIG_GPIO_UNIPHIER
ARM: meson: enable MESON_IRQ_GPIO in Kconfig for meson8b
ARM: meson: Add SMP bringup code for Meson8 and Meson8b
ARM: smp_scu: allow the platform code to read the SCU CPU status
ARM: smp_scu: add a helper for powering on a specific CPU
dt-bindings: Amlogic: Add Meson8 and Meson8b SMP related documentation
ARM: OMAP3: Delete an unnecessary variable initialisation in omap3xxx_hwmod_init()
ARM: OMAP3: Use common error handling code in omap3xxx_hwmod_init()
ARM: defconfig: select the right SX150X driver
arm64: defconfig: Enable QCOM_IOMMU
arm64: Add ThunderX drivers to defconfig
arm64: defconfig: Enable Tegra PCI controller
cpufreq: imx6q: Move speed grading check to cpufreq driver
arm64: defconfig: re-enable Qualcomm DB410c USB
ARM: configs: stm32: Add MDMA support in STM32 defconfig
ARM: imx: Enable cpuidle for i.MX6DL starting at 1.1
bus: ti-sysc: Fix unbalanced pm_runtime_enable by adding remove
bus: ti-sysc: mark PM functions as __maybe_unused
...
- A core irq fix for legacy cases where the irq trigger is not reported
by firmware
- A couple of GICv3/4 fixes (Kconfig, of-node refcount, error handling)
- Trivial pr_err fixes
-----BEGIN PGP SIGNATURE-----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=/8DQ
-----END PGP SIGNATURE-----
Merge tag 'irqchip-4.15-4' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent
Pull irqchip updates for 4.15, take #4 from Marc Zyngier
- A core irq fix for legacy cases where the irq trigger is not reported
by firmware
- A couple of GICv3/4 fixes (Kconfig, of-node refcount, error handling)
- Trivial pr_err fixes
Pull irq core updates from Thomas Gleixner:
"A rather large update for the interrupt core code and the irq chip drivers:
- Add a new bitmap matrix allocator and supporting changes, which is
used to replace the x86 vector allocator which comes with separate
pull request. This allows to replace the convoluted nested loop
allocation function in x86 with a facility which supports the
recently added property of managed interrupts proper and allows to
switch to a best effort vector reservation scheme, which addresses
problems with vector exhaustion.
- A large update to the ARM GIC-V3-ITS driver adding support for
range selectors.
- New interrupt controllers:
- Meson and Meson8 GPIO
- BCM7271 L2
- Socionext EXIU
If you expected that this will stop at some point, I have to
disappoint you. There are new ones posted already. Sigh!
- STM32 interrupt controller support for new platforms.
- A pile of fixes, cleanups and updates to the MIPS GIC driver
- The usual small fixes, cleanups and updates all over the place.
Most visible one is to move the irq chip drivers Kconfig switches
into a separate Kconfig menu"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (70 commits)
genirq: Fix type of shifting literal 1 in __setup_irq()
irqdomain: Drop pointless NULL check in virq_debug_show_one
genirq/proc: Return proper error code when irq_set_affinity() fails
irq/work: Use llist_for_each_entry_safe
irqchip: mips-gic: Print warning if inherited GIC base is used
irqchip/mips-gic: Add pr_fmt and reword pr_* messages
irqchip/stm32: Move the wakeup on interrupt mask
irqchip/stm32: Fix initial values
irqchip/stm32: Add stm32h7 support
dt-bindings/interrupt-controllers: Add compatible string for stm32h7
irqchip/stm32: Add multi-bank management
irqchip/stm32: Select GENERIC_IRQ_CHIP
irqchip/exiu: Add support for Socionext Synquacer EXIU controller
dt-bindings: Add description of Socionext EXIU interrupt controller
irqchip/gic-v3-its: Fix VPE activate callback return value
irqchip: mips-gic: Make IPI bitmaps static
irqchip: mips-gic: Share register writes in gic_set_type()
irqchip: mips-gic: Remove gic_vpes variable
irqchip: mips-gic: Use num_possible_cpus() to reserve IPIs
irqchip: mips-gic: Configure EIC when CPUs come online
...
In some randconfig scenarios, including arm-gic-v4.h results
in a spurious wawrning about the $SUBJECT structure not being
defined. Adding a forward definition keeps it quiet.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
So far, we require the hypervisor to update the VLPI properties
once the the VLPI mapping has been established. While this
makes it easy for the ITS driver, it creates a window where
an incoming interrupt can be delivered with an unknown set
of properties. Not very nice.
Instead, let's add a "properties" field to the mapping structure,
and use that to configure the VLPI before it actually gets mapped.
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
So far, we map all VPEs on all ITSs. While this is not wrong,
this is quite a big hammer, as moving a VPE around requires
all ITSs to be synchronized. Needles to say, this is an
expensive proposition.
Instead, let's switch to a mode where we issue VMAPP commands
only on ITSs that are actually involved in reporting interrupts
to the given VM.
For that purpose, we refcount the number of interrupts are are
mapped for this VM on each ITS, performing the map/unmap
operations as required. It then allows us to use this refcount
to only issue VMOVP to the ITSs that need to know about this
VM.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
As we're about to make use of the maximum number of ITSs in
a GICv4 system, let's make this value global (and rename it to
GICv4_ITS_LIST_MAX).
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
A new feature Range Selector (RS) has been added to GIC specification
in order to support more than 16 CPUs at affinity level 0. New fields
are introduced in SGI system registers (ICC_SGI0R_EL1, ICC_SGI1R_EL1
and ICC_ASGI1R_EL1) to relax an artificial limit of 16 at level 0.
- A new RSS field in ICC_CTLR_EL3, ICC_CTLR_EL1 and ICV_CTLR_EL1:
[18] - Range Selector Support (RSS)
0b0 = Targeted SGIs with affinity level 0 values of 0-15 are supported.
0b1 = Targeted SGIs with affinity level 0 values of 0-255 are supported.
- A new RS field in ICC_SGI0R_EL1, ICC_SGI1R_EL1 and ICC_ASGI1R_EL1:
[47:44] - RangeSelector (RS) which group of 16 TargetList[n] field
TargetList[n] represents aff0 value ((RS*16)+n)
When ICC_CTLR_EL3.RSS==0 or ICC_CTLR_EL1.RSS==0, RS is RES0.
- A new RSS field in GICD_TYPER:
[26] - Range Selector Support (RSS)
0b0 = Targeted SGIs with affinity level 0 values of 0-15 are supported.
0b1 = Targeted SGIs with affinity level 0 values of 0-255 are supported.
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
All mach-omap2 variants are device tree only now, so this function is dead
code. Remove it.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-omap@vger.kernel.org
Cc: Jason Cooper <jason@lakedaemon.net>
Link: https://lkml.kernel.org/r/20171016160422.uu2i7vvrgy7cc4aw@lenoch
The current ITS driver works fine as long as normal memory and GICR
regions are located within the lower 48bit (>=0 && <2^48) physical
address space. Some of the registers GICR_PEND/PROP, GICR_VPEND/VPROP
and GITS_CBASER are handled properly but not all when configuring
the hardware with 52bit physical address.
This patch does the following changes to support 52bit PA.
-Handle 52bit PA in GITS_BASERn.
-Fix ITT_addr width to 52bits, bits[51:8].
-Fix RDbase width to 52bits, bits[51:16].
-Fix VPT_addr width to 52bits, bits[51:16].
Definition of the GITS_BASERn register when ITS PageSize is 64KB:
-Bits[47:16] of the register provide bits[47:16] of the table PA.
-Bits[15:12] of the register provide bits[51:48] of the table PA.
-Bits[15:00] of the base physical address are 0.
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In order to easily provide SMP for BCM2837 on 32-bit and 64-bit
the SMP startup code was placed in irq-bcm2836. That's not the
right approach. So move this code where it belongs.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: 41f4988cc2 ("irqchip/bcm2836: Add SMP support for the 2836")
Tested-by: Eric Anholt <eric@anholt.net>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for 4.14 for MIPS; below a summary of
the non-merge commits:
CM:
- Rename mips_cm_base to mips_gcr_base
- Specify register size when generating accessors
- Use BIT/GENMASK for register fields, order & drop shifts
- Add cluster & block args to mips_cm_lock_other()
CPC:
- Use common CPS accessor generation macros
- Use BIT/GENMASK for register fields, order & drop shifts
- Introduce register modify (set/clear/change) accessors
- Use change_*, set_* & clear_* where appropriate
- Add CM/CPC 3.5 register definitions
- Use GlobalNumber macros rather than magic numbers
- Have asm/mips-cps.h include CM & CPC headers
- Cluster support for topology functions
- Detect CPUs in secondary clusters
CPS:
- Read GIC_VL_IDENT directly, not via irqchip driver
DMA:
- Consolidate coherent and non-coherent dma_alloc code
- Don't use dma_cache_sync to implement fd_cacheflush
FPU emulation / FP assist code:
- Another series of 14 commits fixing corner cases such as NaN
propgagation and other special input values.
- Zero bits 32-63 of the result for a CLASS.D instruction.
- Enhanced statics via debugfs
- Do not use bools for arithmetic. GCC 7.1 moans about this.
- Correct user fault_addr type
Generic MIPS:
- Enhancement of stack backtraces
- Cleanup from non-existing options
- Handle non word sized instructions when examining frame
- Fix detection and decoding of ADDIUSP instruction
- Fix decoding of SWSP16 instruction
- Refactor handling of stack pointer in get_frame_info
- Remove unreachable code from force_fcr31_sig()
- Convert to using %pOF instead of full_name
- Remove the R6000 support.
- Move FP code from *_switch.S to *_fpu.S
- Remove unused ST_OFF from r2300_switch.S
- Allow platform to specify multiple its.S files
- Add #includes to various files to ensure code builds reliable and
without warning..
- Remove __invalidate_kernel_vmap_range
- Remove plat_timer_setup
- Declare various variables & functions static
- Abstract CPU core & VP(E) ID access through accessor functions
- Store core & VP IDs in GlobalNumber-style variable
- Unify checks for sibling CPUs
- Add CPU cluster number accessors
- Prevent direct use of generic_defconfig
- Make CONFIG_MIPS_MT_SMP default y
- Add __ioread64_copy
- Remove unnecessary inclusions of linux/irqchip/mips-gic.h
GIC:
- Introduce asm/mips-gic.h with accessor functions
- Use new GIC accessor functions in mips-gic-timer
- Remove counter access functions from irq-mips-gic.c
- Remove gic_read_local_vp_id() from irq-mips-gic.c
- Simplify shared interrupt pending/mask reads in irq-mips-gic.c
- Simplify gic_local_irq_domain_map() in irq-mips-gic.c
- Drop gic_(re)set_mask() functions in irq-mips-gic.c
- Remove gic_set_polarity(), gic_set_trigger(), gic_set_dual_edge(),
gic_map_to_pin() and gic_map_to_vpe() from irq-mips-gic.c.
- Convert remaining shared reg access, local int mask access and
remaining local reg access to new accessors
- Move GIC_LOCAL_INT_* to asm/mips-gic.h
- Remove GIC_CPU_INT* macros from irq-mips-gic.c
- Move various definitions to the driver
- Remove gic_get_usm_range()
- Remove __gic_irq_dispatch() forward declaration
- Remove gic_init()
- Use mips_gic_present() in place of gic_present and remove
gic_present
- Move gic_get_c0_*_int() to asm/mips-gic.h
- Remove linux/irqchip/mips-gic.h
- Inline __gic_init()
- Inline gic_basic_init()
- Make pcpu_masks a per-cpu variable
- Use pcpu_masks to avoid reading GIC_SH_MASK*
- Clean up mti, reserved-cpu-vectors handling
- Use cpumask_first_and() in gic_set_affinity()
- Let the core set struct irq_common_data affinity
microMIPS:
- Fix microMIPS stack unwinding on big endian systems
MIPS-GIC:
- SYNC after enabling GIC region
NUMA:
- Remove the unused parent_node() macro
R6:
- Constify r2_decoder_tables
- Add accessor & bit definitions for GlobalNumber
SMP:
- Constify smp ops
- Allow boot_secondary SMP op to return errors
VDSO:
- Drop gic_get_usm_range() usage
- Avoid use of linux/irqchip/mips-gic.h
Platform changes:
Alchemy:
- Add devboard machine type to cpuinfo
- update cpu feature overrides
- Threaded carddetect irqs for devboards
AR7:
- allow NULL clock for clk_get_rate
BCM63xx:
- Fix ENETDMA_6345_MAXBURST_REG offset
- Allow NULL clock for clk_get_rate
CI20:
- Enable GPIO and RTC drivers in defconfig
- Add ethernet and fixed-regulator nodes to DTS
Generic platform:
- Move Boston and NI 169445 FIT image source to their own files
- Include asm/bootinfo.h for plat_fdt_relocated()
- Include asm/time.h for get_c0_*_int()
- Include asm/bootinfo.h for plat_fdt_relocated()
- Include asm/time.h for get_c0_*_int()
- Allow filtering enabled boards by requirements
- Don't explicitly disable CONFIG_USB_SUPPORT
- Bump default NR_CPUS to 16
JZ4700:
- Probe the jz4740-rtc driver from devicetree
Lantiq:
- Drop check of boot select from the spi-falcon driver.
- Drop check of boot select from the lantiq-flash MTD driver.
- Access boot cause register in the watchdog driver through regmap
- Add device tree binding documentation for the watchdog driver
- Add docs for the RCU DT bindings.
- Convert the fpi bus driver to a platform_driver
- Remove ltq_reset_cause() and ltq_boot_select(
- Switch to a proper reset driver
- Switch to a new drivers/soc GPHY driver
- Add an USB PHY driver for the Lantiq SoCs using the RCU module
- Use of_platform_default_populate instead of __dt_register_buses
- Enable MFD_SYSCON to be able to use it for the RCU MFD
- Replace ltq_boot_select() with dummy implementation.
Loongson 2F:
- Allow NULL clock for clk_get_rate
Malta:
- Use new GIC accessor functions
NI 169445:
- Add support for NI 169445 board.
- Only include in 32r2el kernels
Octeon:
- Add support for watchdog of 78XX SOCs.
- Add support for watchdog of CN68XX SOCs.
- Expose support for mips32r1, mips32r2 and mips64r1
- Enable more drivers in config file
- Add support for accessing the boot vector.
- Remove old boot vector code from watchdog driver
- Define watchdog registers for 70xx, 73xx, 78xx, F75xx.
- Make CSR functions node aware.
- Allow access to CIU3 IRQ domains.
- Misc cleanups in the watchdog driver
Omega2+:
- New board, add support and defconfig
Pistachio:
- Enable Root FS on NFS in defconfig
Ralink:
- Add Mediatek MT7628A SoC
- Allow NULL clock for clk_get_rate
- Explicitly request exclusive reset control in the pci-mt7620 PCI driver.
SEAD3:
- Only include in 32 bit kernels by default
VoCore:
- Add VoCore as a vendor t0 dt-bindings
- Add defconfig file"
* '4.14-features' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (167 commits)
MIPS: Refactor handling of stack pointer in get_frame_info
MIPS: Stacktrace: Fix microMIPS stack unwinding on big endian systems
MIPS: microMIPS: Fix decoding of swsp16 instruction
MIPS: microMIPS: Fix decoding of addiusp instruction
MIPS: microMIPS: Fix detection of addiusp instruction
MIPS: Handle non word sized instructions when examining frame
MIPS: ralink: allow NULL clock for clk_get_rate
MIPS: Loongson 2F: allow NULL clock for clk_get_rate
MIPS: BCM63XX: allow NULL clock for clk_get_rate
MIPS: AR7: allow NULL clock for clk_get_rate
MIPS: BCM63XX: fix ENETDMA_6345_MAXBURST_REG offset
mips: Save all registers when saving the frame
MIPS: Add DWARF unwinding to assembly
MIPS: Make SAVE_SOME more standard
MIPS: Fix issues in backtraces
MIPS: jz4780: DTS: Probe the jz4740-rtc driver from devicetree
MIPS: Ci20: Enable RTC driver
watchdog: octeon-wdt: Add support for 78XX SOCs.
watchdog: octeon-wdt: Add support for cn68XX SOCs.
watchdog: octeon-wdt: File cleaning.
...
The linux/irqchip/mips-gic.h header is no longer used. Remove it.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17049/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Our VDSO code makes use of macros from linux/irqchip/mips-gic.h to
provide offsets to register values, but these are trivial offsets to the
two 32 bit halves of a 64 bit value. Replace use of the macros with zero
(ie. omit adding an offset) and the size of the low 32 bit of the value.
This removes our need for linux/irqchip/mips-gic.h & prepares us for it
to be removed.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17047/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The linux/irqchip/mips-gic.h header is now almost empty. Move the
declarations of gic_get_c0_compare_int(), gic_get_c0_perfcount_int() &
gic_get_c0_fdc_int() to asm/mips-gic.h in order to close in on being
able to delete the former header.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17046/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Nothing uses the global gic_present variable anymore; mips_gic_present()
should be used instead. Remove the dead code.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17045/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
All in-tree platforms now probe the GIC driver using device tree, and as
such nothing calls gic_init() any longer. Remove the dead code.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17043/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The MIPS VDSO code is no longer reliant upon the irqchip driver to
provide the address of the GIC's user-visible section via
gic_get_usm_range(). Remove the now-dead code.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17041/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move the definitions of macros used to convert between hardware IRQ
numbers & shared or local interrupt numbers into the irqchip driver,
which is all that should ever need to care about them.
Remove GIC_CPU_TO_VEC_OFFSET() in the process since it's never used.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17039/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The GIC_CPU_INT* macros are never used. Remove the dead code.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17038/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move the definition of VP-local interrupts provided by the MIPS Global
Interrupt Controller to the new asm/mips-gic.h header to be alongside
the new accessor functions. Whilst at it, convert to an enum which lends
itself more easily to expansion & documentation.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17037/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Convert the remaining accesses to registers in the GIC VP-local &
VP-other register blocks to use the new accessor functions provided by
asm/mips-gic.h, resulting in code which is often shorter & easier to
read.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17036/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use the new accessor functions provided by asm/mips-gic.h to access
masks controlling local interrupts, resulting in code which is often
shorter & easier to read.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17035/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Convert the remaining accesses to registers in the GIC shared register
block to use the new accessor functions provided by asm/mips-gic.h,
resulting in code which is often shorter & easier to read.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17034/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove the gic_map_to_vpe() function in favour of using the new
write_gic_map_vp() accessor function which isn't any more complex to
use & allows us to drop a level of abstraction.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17033/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove the gic_map_to_pin() function in favour of using the new
write_gic_map_pin() accessor function which isn't any more complex to
use & allows us to drop a level of abstraction.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17032/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove the gic_set_dual_edge() function in favour of using the new
change_gic_dual() accessor function which provides equivalent
functionality. This also allows us to remove the gic_update_bits()
function which gic_set_dual_edge() was the last user of, along with the
GIC_INTR_OFS() & GIC_INTR_BIT() macros.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17031/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove the gic_set_trigger() function in favour of using the new
change_gic_trig() accessor function which provides equivalent
functionality.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17030/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove the gic_set_polarity() function in favour of using the new
change_gic_pol() accessor function which provides equivalent
functionality.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17029/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The gic_set_mask() & gic_reset_mask() functions are now no more
convenient to call than the write_gic_smask() or write_gic_rmask()
accessor functions. Remove the layer of abstraction.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17028/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Simplify gic_local_irq_domain_map() by:
- Moving the check for invalid IRQs outside of the loop.
- Moving the decision about whether to use gic_cpu_pin or timer_cpu_pin
outside of the loop.
- Using the new write_gic_vo_map() accessor function to avoid the need
to handle each map register separately.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17027/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Simplify the reads of the bitmaps indicating pending & masked interrupts
in gic_handle_shared_int() using the __ioread32_copy() &
__ioread64_copy() helper functions.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17026/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Nothing needs gic_read_local_vp_id() any longer, so remove the dead
code.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17024/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The MIPS GIC clocksource driver is no longer using the accessor
functions provided by the irqchip driver, so remove them.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17022/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
As KVM needs to know about the availability of GICv4 to enable
direct injection of interrupts, let's advertise the feature in
the gic_kvm_info structure.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add the required interfaces to map, unmap and update a VLPI.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add the required interfaces to schedule a VPE and perform a
VINVALL command.
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
When creating a VM, it is very convenient to have an irq domain
containing all the doorbell interrupts associated with that VM
(each interrupt representing a VPE).
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
A long time ago, GITS_CTLR[1] used to be called GITC_CTLR.EnableVLPI.
It has been subsequently deprecated and is now an "Implementation
Defined" bit that may ot may not be set for GICv4. Brilliant.
And the current crop of the FastModel requires that bit for VLPIs
to be enabled. Oh well... Let's set it and find out what breaks.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
When we don't have the DirectLPI feature, we must work around the
architecture shortcomings to be able to perform the required
maintenance (interrupt masking, clearing and injection).
For this, we create a fake device whose sole purpose is to
provide a way to issue commands as if we were dealing with LPIs
coming from that device (while they actually originate from
the ITS). This fake device doesn't have LPIs allocated to it,
but instead uses the VPE LPIs.
Of course, this could be a real bottleneck, and a naive
implementation would require 6 commands to issue an invalidation.
Instead, let's allocate at least one event per physical CPU
(rounded up to the next power of 2), and opportunistically
map the VPE doorbell to an event. This doorbell will be mapped
until we roll over and need to reallocate this slot.
This ensures that most of the time, we only need 2 commands
to issue an INV, INT or CLEAR, making the performance a lot
better, given that we always issue a CLEAR on entry, and
an INV on each side of a trapped WFI.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
When a VPE is scheduled to run, the corresponding redistributor must
be told so, by setting VPROPBASER to the VM's property table, and
VPENDBASER to the vcpu's pending table.
When scheduled out, we preserve the IDAI and PendingLast bits. The
latter is specially important, as it tells the hypervisor that
there are pending interrupts for this vcpu.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
V{PEND,PROP}BASER being 64bit registers, they need some ad-hoc
accessors on 32bit, specially given that VPENDBASER contains
a Valid bit, making the access a bit convoluted.
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add the new GICv4 ITS command definitions, most of them, being
defined in terms of their physical counterparts.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add a bunch of GICv4-specific data structures that will get used in
subsequent patches.
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add the probing code for the ITS VLPI support. This includes
configuring the ITS number if not supporting the single VMOVP
command feature.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add helper functions that probe for VLPI and DirectLPI properties.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Now that we're able to safely handle common sysreg access, let's
give the user the opportunity to enable it by passing a specific
command-line option (vgic_v3.common_trap).
Tested-by: Alexander Graf <agraf@suse.de>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
In order to be able to trap Group-0 GICv3 system registers, we need to
set ICH_HCR_EL2.TALL0 begore entering the guest. This is conditionnaly
done after having restored the guest's state, and cleared on exit.
Tested-by: Alexander Graf <agraf@suse.de>
Acked-by: David Daney <david.daney@cavium.com>
Acked-by: Christoffer Dall <cdall@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
In order to be able to trap Group-1 GICv3 system registers, we need to
set ICH_HCR_EL2.TALL1 before entering the guest. This is conditionally
done after having restored the guest's state, and cleared on exit.
Tested-by: Alexander Graf <agraf@suse.de>
Acked-by: David Daney <david.daney@cavium.com>
Acked-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Add a handler for writing the guest's view of the ICC_EOIR1_EL1
register. This involves dropping the priority of the interrupt,
and deactivating it if required (EOImode == 0).
Tested-by: Alexander Graf <agraf@suse.de>
Acked-by: David Daney <david.daney@cavium.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Add a handler for reading the guest's view of the ICC_IAR1_EL1
register. This involves finding the highest priority Group-1
interrupt, checking against both PMR and the active group
priority, activating the interrupt and setting the group
priority as active.
Tested-by: Alexander Graf <agraf@suse.de>
Acked-by: David Daney <david.daney@cavium.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
We have been a little loose with our intermediate VMCR representation
where we had a 'ctlr' field, but we failed to differentiate between the
GICv2 GICC_CTLR and ICC_CTLR_EL1 layouts, and therefore ended up mapping
the wrong bits into the individual fields of the ICH_VMCR_EL2 when
emulating a GICv2 on a GICv3 system.
Fix this by using explicit fields for the VMCR bits instead.
Cc: Eric Auger <eric.auger@redhat.com>
Reported-by: wanghaibin <wanghaibin.wang@huawei.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Changes include:
- A fix related to the 32-bit idmap stub
- A fix to the bitmask used to deode the operands of an AArch32 CP
instruction
- We have moved the files shared between arch/arm/kvm and
arch/arm64/kvm to virt/kvm/arm
- We add support for saving/restoring the virtual ITS state to
userspace
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZEZihAAoJEEtpOizt6ddyGDYH/jmGjDMnryORn2P2o10dUQKJ
RnHTQYnpOYqnprlkFtZFpmK+mjl/a8R1Btb7GK2EwmovTR95pMYPRqtrCTOL0aQA
4OToh7+vFGatwxsGCS6utazdhmx0UT/LhO/GEF4G1zOb7eVa4ZtS1NKLP2WjPD1E
RU3Qn8wa0pESv3tJScv8qo2+PWVX4krbFllhY2Hk0AkVQcI66ExkdVq4ikm1eUXn
rxzIayLG2bv3KEPNCzozdwoY9tDL+b40q6vN/RHGJmM05SZbbSx2/Bkw2RbslSpD
2hvhHWX7xeuEBcd5mZO7sP4WS3hM/BI8eX7q+uMeNJ9B+nM82yjGfOTtglVi2cc=
=JfvQ
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-for-v4.12-round2' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
Second round of KVM/ARM Changes for v4.12.
Changes include:
- A fix related to the 32-bit idmap stub
- A fix to the bitmask used to deode the operands of an AArch32 CP
instruction
- We have moved the files shared between arch/arm/kvm and
arch/arm64/kvm to virt/kvm/arm
- We add support for saving/restoring the virtual ITS state to
userspace
this new helper synchronizes the irq pending_latch
with the LPI pending bit status found in rdist pending table.
As the status is consumed, we reset the bit in pending table.
As we need the PENDBASER_ADDRESS() in vgic-v3, let's move its
definition in the irqchip header. We restore the full length
of the field, ie [51:16]. Same for PROPBASER_ADDRESS with full
field length of [51:12].
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Up to now the MAPD's ITT size field has been ignored. It encodes
the number of eventid bit minus 1. It should be used to check
the eventid when a MAPTI command is issued on a device. Let's
store the number of eventid bits in the its_device and do the
check on MAPTI. Also make sure the ITT size field does
not exceed the GITS_TYPER IDBITS field.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
The GITS_IIDR revision field is used to encode the migration ABI
revision. So we need to restore it to check the table layout is
readable by the destination.
By writing the IIDR, userspace thus forces the ABI revision to be
used and this must be less than or equal to the max revision KVM
supports.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
We plan to support different migration ABIs, ie. characterizing
the ITS table layout format in guest RAM. For example, a new ABI
will be needed if vLPIs get supported for nested use case.
So let's introduce an array of supported ABIs (at the moment a single
ABI is supported though). The following characteristics are foreseen
to vary with the ABI: size of table entries, save/restore operation,
the way abi settings are applied.
By default the MAX_ABI_REV is applied on its creation. In subsequent
patches we will introduce a way for the userspace to change the ABI
in use.
The entry sizes now are set according to the ABI version and not
hardcoded anymore.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Pull timer updates from Thomas Gleixner:
"The timer departement delivers:
- more year 2038 rework
- a massive rework of the arm achitected timer
- preparatory patches to allow NTP correction of clock event devices
to avoid early expiry
- the usual pile of fixes and enhancements all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (91 commits)
timer/sysclt: Restrict timer migration sysctl values to 0 and 1
arm64/arch_timer: Mark errata handlers as __maybe_unused
Clocksource/mips-gic: Remove redundant non devicetree init
MIPS/Malta: Probe gic-timer via devicetree
clocksource: Use GENMASK_ULL in definition of CLOCKSOURCE_MASK
acpi/arm64: Add SBSA Generic Watchdog support in GTDT driver
clocksource: arm_arch_timer: add GTDT support for memory-mapped timer
acpi/arm64: Add memory-mapped timer support in GTDT driver
clocksource: arm_arch_timer: simplify ACPI support code.
acpi/arm64: Add GTDT table parse driver
clocksource: arm_arch_timer: split MMIO timer probing.
clocksource: arm_arch_timer: add structs to describe MMIO timer
clocksource: arm_arch_timer: move arch_timer_needs_of_probing into DT init call
clocksource: arm_arch_timer: refactor arch_timer_needs_probing
clocksource: arm_arch_timer: split dt-only rate handling
x86/uv/time: Set ->min_delta_ticks and ->max_delta_ticks
unicore32/time: Set ->min_delta_ticks and ->max_delta_ticks
um/time: Set ->min_delta_ticks and ->max_delta_ticks
tile/time: Set ->min_delta_ticks and ->max_delta_ticks
score/time: Set ->min_delta_ticks and ->max_delta_ticks
...
Malta was the only platform probing this driver from platform code
without using device tree. With that code removed, gic_clocksource_init
is redundant so remove it.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Link: http://lkml.kernel.org/r/1492604806-23420-2-git-send-email-matt.redfearn@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
As an oversight, for GICv2, we accidentally export the GICC_PMR register
in the format of the GICH_VMCR.VMPriMask field in the lower 5 bits of a
word, meaning that userspace must always use the lower 5 bits to
communicate with the KVM device and must shift the value left by 3
places to obtain the actual priority mask level.
Since GICv3 supports the full 8 bits of priority masking in the ICH_VMCR,
we have to fix the value we export when emulating a GICv2 on top of a
hardware GICv3 and exporting the emulated GICv2 state to userspace.
Take the chance to clarify this aspect of the ABI.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Our GICv3 emulation always presents ICC_SRE_EL1 with DIB/DFB set to
zero, which implies that there is a way to bypass the GIC and
inject raw IRQ/FIQ by driving the CPU pins.
Of course, we don't allow that when the GIC is configured, but
we fail to indicate that to the guest. The obvious fix is to
set these bits (and never let them being changed again).
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Christoffer Dall <cdall@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
200 commits and noteworthy changes for most architectures.
* ARM:
- GICv3 save/restore
- cache flushing fixes
- working MSI injection for GICv3 ITS
- physical timer emulation
* MIPS:
- various improvements under the hood
- support for SMP guests
- a large rewrite of MMU emulation. KVM MIPS can now use MMU notifiers
to support copy-on-write, KSM, idle page tracking, swapping, ballooning
and everything else. KVM_CAP_READONLY_MEM is also supported, so that
writes to some memory regions can be treated as MMIO. The new MMU also
paves the way for hardware virtualization support.
* PPC:
- support for POWER9 using the radix-tree MMU for host and guest
- resizable hashed page table
- bugfixes.
* s390: expose more features to the guest
- more SIMD extensions
- instruction execution protection
- ESOP2
* x86:
- improved hashing in the MMU
- faster PageLRU tracking for Intel CPUs without EPT A/D bits
- some refactoring of nested VMX entry/exit code, preparing for live
migration support of nested hypervisors
- expose yet another AVX512 CPUID bit
- host-to-guest PTP support
- refactoring of interrupt injection, with some optimizations thrown in
and some duct tape removed.
- remove lazy FPU handling
- optimizations of user-mode exits
- optimizations of vcpu_is_preempted() for KVM guests
* generic:
- alternative signaling mechanism that doesn't pound on tsk->sighand->siglock
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJYral1AAoJEL/70l94x66DbNgH/Rx8YXuidFq2fe3RWOvld3RK
85OM/D5g38cTLpBE0/sJpcvX34iYN8U/l5foCZwpxB+83GHEk2Cr57JyfTogdaAJ
x8dBhHKQCA/HxSQUQLN6nFqRV+yT8WUR92Fhqx82+80BSen5Yzcfee/TDoW6T1IW
g8CYgX9FrRaGOX066ImAuUfdAdUVjyssfs9VttDTX+HiusPeuBPx/wsRe1ZEEPlH
vnltIJQb1ETV2GOZLUojKjzH6aZkjIl29XxjkYii9JTUornClG0DfW+5QT3uLrB5
gJ+G+Zmpsq8ZBx9jNDtAi7sFsoPY1Mzf+JPNCGXBra2sP2GrBAuXcxmgznRYltQ=
=8IIp
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"4.11 is going to be a relatively large release for KVM, with a little
over 200 commits and noteworthy changes for most architectures.
ARM:
- GICv3 save/restore
- cache flushing fixes
- working MSI injection for GICv3 ITS
- physical timer emulation
MIPS:
- various improvements under the hood
- support for SMP guests
- a large rewrite of MMU emulation. KVM MIPS can now use MMU
notifiers to support copy-on-write, KSM, idle page tracking,
swapping, ballooning and everything else. KVM_CAP_READONLY_MEM is
also supported, so that writes to some memory regions can be
treated as MMIO. The new MMU also paves the way for hardware
virtualization support.
PPC:
- support for POWER9 using the radix-tree MMU for host and guest
- resizable hashed page table
- bugfixes.
s390:
- expose more features to the guest
- more SIMD extensions
- instruction execution protection
- ESOP2
x86:
- improved hashing in the MMU
- faster PageLRU tracking for Intel CPUs without EPT A/D bits
- some refactoring of nested VMX entry/exit code, preparing for live
migration support of nested hypervisors
- expose yet another AVX512 CPUID bit
- host-to-guest PTP support
- refactoring of interrupt injection, with some optimizations thrown
in and some duct tape removed.
- remove lazy FPU handling
- optimizations of user-mode exits
- optimizations of vcpu_is_preempted() for KVM guests
generic:
- alternative signaling mechanism that doesn't pound on
tsk->sighand->siglock"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (195 commits)
x86/kvm: Provide optimized version of vcpu_is_preempted() for x86-64
x86/paravirt: Change vcp_is_preempted() arg type to long
KVM: VMX: use correct vmcs_read/write for guest segment selector/base
x86/kvm/vmx: Defer TR reload after VM exit
x86/asm/64: Drop __cacheline_aligned from struct x86_hw_tss
x86/kvm/vmx: Simplify segment_base()
x86/kvm/vmx: Get rid of segment_base() on 64-bit kernels
x86/kvm/vmx: Don't fetch the TSS base from the GDT
x86/asm: Define the kernel TSS limit in a macro
kvm: fix page struct leak in handle_vmon
KVM: PPC: Book3S HV: Disable HPT resizing on POWER9 for now
KVM: Return an error code only as a constant in kvm_get_dirty_log()
KVM: Return an error code only as a constant in kvm_get_dirty_log_protect()
KVM: Return directly after a failed copy_from_user() in kvm_vm_compat_ioctl()
KVM: x86: remove code for lazy FPU handling
KVM: race-free exit from KVM_RUN without POSIX signals
KVM: PPC: Book3S HV: Turn "KVM guest htab" message into a debug message
KVM: PPC: Book3S PR: Ratelimit copy data failure error messages
KVM: Support vCPU-based gfn->hva cache
KVM: use separate generations for each address space
...
GICD_TYPER_LPIS macro is defined twice in this file. This patch removes the
duplicate entry.
Fixes: f5c1434c21 ("irqchip: GICv3: rework redistributor structure")
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Back in the days when the GICv3/v4 architecture was drafted,
the command to an event to an LPI number was called MAPVI.
Later on, and to avoid confusion with the GICv4 command VMAPI,
it was renamed MAPTI. We've carried the old name for a long
time, but it gets in the way of people reading the code in
the light of the public architecture specification.
Just repaint all the references and kill the old definition.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
During the development of the GICv3/v4 architecture, it was
envisaged to have a CPU table, though the use for it was
never completely clear (the collection table serves that role
pretty well). It ended being dropped before the specification
was published, though it lived on in the driver.
In order to avoid people scratching their head too much, let's do
the same in the kernel.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
ICC_VMCR_EL2 supports virtual access to ICC_IGRPEN1_EL1.Enable
and ICC_IGRPEN0_EL1.Enable fields. Add grpen0 and grpen1 member
variables to struct vmcr to support read and write of these fields.
Also refactor vgic_set_vmcr and vgic_get_vmcr() code.
Drop ICH_VMCR_CTLR_SHIFT and ICH_VMCR_CTLR_MASK macros and instead
use ICH_VMCR_EOI* and ICH_VMCR_CBPR* macros.
Signed-off-by: Vijaya Kumar K <Vijaya.Kumar@cavium.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Define register definitions for ICH_VMCR_EL2, ICC_CTLR_EL1 and
ICH_VTR_EL2, ICC_BPR0_EL1, ICC_BPR1_EL1 registers.
Signed-off-by: Vijaya Kumar K <Vijaya.Kumar@cavium.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
There is no point in having an extra type for extra confusion. u64 is
unambiguous.
Conversion was done with the following coccinelle script:
@rem@
@@
-typedef u64 cycle_t;
@fix@
typedef cycle_t;
@@
-cycle_t
+u64
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: John Stultz <john.stultz@linaro.org>
x86: userspace can now hide nested VMX features from guests; nested
VMX can now run Hyper-V in a guest; support for AVX512_4VNNIW and
AVX512_FMAPS in KVM; infrastructure support for virtual Intel GPUs.
PPC: support for KVM guests on POWER9; improved support for interrupt
polling; optimizations and cleanups.
s390: two small optimizations, more stuff is in flight and will be
in 4.11.
ARM: support for the GICv3 ITS on 32bit platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQExBAABCAAbBQJYTkP0FBxwYm9uemluaUByZWRoYXQuY29tAAoJEL/70l94x66D
lZIH/iT1n9OQXcuTpYYnQhuCenzI3GZZOIMTbCvK2i5bo0FIJKxVn0EiAAqZSXvO
nO185FqjOgLuJ1AD1kJuxzye5suuQp4HIPWWgNHcexLuy43WXWKZe0IQlJ4zM2Xf
u31HakpFmVDD+Cd1qN3yDXtDrRQ79/xQn2kw7CWb8olp+pVqwbceN3IVie9QYU+3
gCz0qU6As0aQIwq2PyalOe03sO10PZlm4XhsoXgWPG7P18BMRhNLTDqhLhu7A/ry
qElVMANT7LSNLzlwNdpzdK8rVuKxETwjlc1UP8vSuhrwad4zM2JJ1Exk26nC2NaG
D0j4tRSyGFIdx6lukZm7HmiSHZ0=
=mkoB
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"Small release, the most interesting stuff is x86 nested virt
improvements.
x86:
- userspace can now hide nested VMX features from guests
- nested VMX can now run Hyper-V in a guest
- support for AVX512_4VNNIW and AVX512_FMAPS in KVM
- infrastructure support for virtual Intel GPUs.
PPC:
- support for KVM guests on POWER9
- improved support for interrupt polling
- optimizations and cleanups.
s390:
- two small optimizations, more stuff is in flight and will be in
4.11.
ARM:
- support for the GICv3 ITS on 32bit platforms"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (94 commits)
arm64: KVM: pmu: Reset PMSELR_EL0.SEL to a sane value before entering the guest
KVM: arm/arm64: timer: Check for properly initialized timer on init
KVM: arm/arm64: vgic-v2: Limit ITARGETSR bits to number of VCPUs
KVM: x86: Handle the kthread worker using the new API
KVM: nVMX: invvpid handling improvements
KVM: nVMX: check host CR3 on vmentry and vmexit
KVM: nVMX: introduce nested_vmx_load_cr3 and call it on vmentry
KVM: nVMX: propagate errors from prepare_vmcs02
KVM: nVMX: fix CR3 load if L2 uses PAE paging and EPT
KVM: nVMX: load GUEST_EFER after GUEST_CR0 during emulated VM-entry
KVM: nVMX: generate MSR_IA32_CR{0,4}_FIXED1 from guest CPUID
KVM: nVMX: fix checks on CR{0,4} during virtual VMX operation
KVM: nVMX: support restore of VMX capability MSRs
KVM: nVMX: generate non-true VMX MSRs based on true versions
KVM: x86: Do not clear RFLAGS.TF when a singlestep trap occurs.
KVM: x86: Add kvm_skip_emulated_instruction and use it.
KVM: VMX: Move skip_emulated_instruction out of nested_vmx_check_vmcs12
KVM: VMX: Reorder some skip_emulated_instruction calls
KVM: x86: Add a return value to kvm_emulate_cpuid
KVM: PPC: Book3S: Move prototypes for KVM functions into kvm_ppc.h
...
Make sure that constants which are supposed to be applied on 64-bit
data is actually unsigned long long, so they won't be truncated when
used in 32-bit mode.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Evaluate GITS_BASER_ENTRY_SIZE once as an int data (GITS_BASER<n>'s
Entry Size is 5-bit wide only), so when used as divider no reference
to __aeabi_uldivmod is generated when build for AArch32.
Use unsigned long long for GITS_BASER_PAGE_SIZE_* since they are
used in conjunction with 64-bit data.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Entry Size in GITS_BASER<n> occupies 5 bits [52:48], but we mask out 8
bits.
Fixes: cc2d3216f5 ("irqchip: GICv3: ITS command queue")
Cc: stable@vger.kernel.org
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In order to add ACPI support we need to isolate ACPI&DT common code and
move DT logic to corresponding functions. To achieve this we are using
firmware agnostic handle which can be unpacked to either DT or ACPI node.
No functional changes other than a very minor one:
1. Terminate its_init call with -ENODEV for non-DT case which allows
to remove hack from its-gic-v3.c.
2. Fix ITS base register address type (from 'unsigned long' to 'phys_addr_t'),
as a bonus we get nice string formatting.
3. Since there is only one of ITS parent domain convert it to static global
variable and drop the parameter from its_probe_one. Users can refer to it
in more convenient way then.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
According to the KVM API documentation a successful MSI injection
should return a value > 0 on success.
Return possible errors in vgic_its_trigger_msi() and report a
successful injection back to userland, while also reporting the
case where the MSI could not be delivered due to the guest not
having the LPI mapped, for instance.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
VGIC implementation.
- s390: support for trapping software breakpoints, nested virtualization
(vSIE), the STHYI opcode, initial extensions for CPU model support.
- MIPS: support for MIPS64 hosts (32-bit guests only) and lots of cleanups,
preliminary to this and the upcoming support for hardware virtualization
extensions.
- x86: support for execute-only mappings in nested EPT; reduced vmexit
latency for TSC deadline timer (by about 30%) on Intel hosts; support for
more than 255 vCPUs.
- PPC: bugfixes.
The ugly bit is the conflicts. A couple of them are simple conflicts due
to 4.7 fixes, but most of them are with other trees. There was definitely
too much reliance on Acked-by here. Some conflicts are for KVM patches
where _I_ gave my Acked-by, but the worst are for this pull request's
patches that touch files outside arch/*/kvm. KVM submaintainers should
probably learn to synchronize better with arch maintainers, with the
latter providing topic branches whenever possible instead of Acked-by.
This is what we do with arch/x86. And I should learn to refuse pull
requests when linux-next sends scary signals, even if that means that
submaintainers have to rebase their branches.
Anyhow, here's the list:
- arch/x86/kvm/vmx.c: handle_pcommit and EXIT_REASON_PCOMMIT was removed
by the nvdimm tree. This tree adds handle_preemption_timer and
EXIT_REASON_PREEMPTION_TIMER at the same place. In general all mentions
of pcommit have to go.
There is also a conflict between a stable fix and this patch, where the
stable fix removed the vmx_create_pml_buffer function and its call.
- virt/kvm/kvm_main.c: kvm_cpu_notifier was removed by the hotplug tree.
This tree adds kvm_io_bus_get_dev at the same place.
- virt/kvm/arm/vgic.c: a few final bugfixes went into 4.7 before the
file was completely removed for 4.8.
- include/linux/irqchip/arm-gic-v3.h: this one is entirely our fault;
this is a change that should have gone in through the irqchip tree and
pulled by kvm-arm. I think I would have rejected this kvm-arm pull
request. The KVM version is the right one, except that it lacks
GITS_BASER_PAGES_SHIFT.
- arch/powerpc: what a mess. For the idle_book3s.S conflict, the KVM
tree is the right one; everything else is trivial. In this case I am
not quite sure what went wrong. The commit that is causing the mess
(fd7bacbca4, "KVM: PPC: Book3S HV: Fix TB corruption in guest exit
path on HMI interrupt", 2016-05-15) touches both arch/powerpc/kernel/
and arch/powerpc/kvm/. It's large, but at 396 insertions/5 deletions
I guessed that it wasn't really possible to split it and that the 5
deletions wouldn't conflict. That wasn't the case.
- arch/s390: also messy. First is hypfs_diag.c where the KVM tree
moved some code and the s390 tree patched it. You have to reapply the
relevant part of commits 6c22c98637, plus all of e030c1125e, to
arch/s390/kernel/diag.c. Or pick the linux-next conflict
resolution from http://marc.info/?l=kvm&m=146717549531603&w=2.
Second, there is a conflict in gmap.c between a stable fix and 4.8.
The KVM version here is the correct one.
I have pushed my resolution at refs/heads/merge-20160802 (commit
3d1f53419842) at git://git.kernel.org/pub/scm/virt/kvm/kvm.git.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJXoGm7AAoJEL/70l94x66DugQIAIj703ePAFepB/fCrKHkZZia
SGrsBdvAtNsOhr7FQ5qvvjLxiv/cv7CymeuJivX8H+4kuUHUllDzey+RPHYHD9X7
U6n1PdCH9F15a3IXc8tDjlDdOMNIKJixYuq1UyNZMU6NFwl00+TZf9JF8A2US65b
x/41W98ilL6nNBAsoDVmCLtPNWAqQ3lajaZELGfcqRQ9ZGKcAYOaLFXHv2YHf2XC
qIDMf+slBGSQ66UoATnYV2gAopNlWbZ7n0vO6tE2KyvhHZ1m399aBX1+k8la/0JI
69r+Tz7ZHUSFtmlmyByi5IAB87myy2WQHyAPwj+4vwJkDGPcl0TrupzbG7+T05Y=
=42ti
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
- ARM: GICv3 ITS emulation and various fixes. Removal of the
old VGIC implementation.
- s390: support for trapping software breakpoints, nested
virtualization (vSIE), the STHYI opcode, initial extensions
for CPU model support.
- MIPS: support for MIPS64 hosts (32-bit guests only) and lots
of cleanups, preliminary to this and the upcoming support for
hardware virtualization extensions.
- x86: support for execute-only mappings in nested EPT; reduced
vmexit latency for TSC deadline timer (by about 30%) on Intel
hosts; support for more than 255 vCPUs.
- PPC: bugfixes.
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (302 commits)
KVM: PPC: Introduce KVM_CAP_PPC_HTM
MIPS: Select HAVE_KVM for MIPS64_R{2,6}
MIPS: KVM: Reset CP0_PageMask during host TLB flush
MIPS: KVM: Fix ptr->int cast via KVM_GUEST_KSEGX()
MIPS: KVM: Sign extend MFC0/RDHWR results
MIPS: KVM: Fix 64-bit big endian dynamic translation
MIPS: KVM: Fail if ebase doesn't fit in CP0_EBase
MIPS: KVM: Use 64-bit CP0_EBase when appropriate
MIPS: KVM: Set CP0_Status.KX on MIPS64
MIPS: KVM: Make entry code MIPS64 friendly
MIPS: KVM: Use kmap instead of CKSEG0ADDR()
MIPS: KVM: Use virt_to_phys() to get commpage PFN
MIPS: Fix definition of KSEGX() for 64-bit
KVM: VMX: Add VMCS to CPU's loaded VMCSs before VMPTRLD
kvm: x86: nVMX: maintain internal copy of current VMCS
KVM: PPC: Book3S HV: Save/restore TM state in H_CEDE
KVM: PPC: Book3S HV: Pull out TM state save/restore into separate procedures
KVM: arm64: vgic-its: Simplify MAPI error handling
KVM: arm64: vgic-its: Make vgic_its_cmd_handle_mapi similar to other handlers
KVM: arm64: vgic-its: Turn device_id validation into generic ID validation
...
Let's restore some of the #defines that have been savagely dropped
by the introduction of the KVM ITS code, as pointlessly break
other users (including series that are already in -next).
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
arm-gic-v3.h contains bit and register definitions for the GICv3 and ITS,
at least for the bits the we currently care about.
The ITS emulation needs more definitions, so add them and refactor
the memory attribute #defines to be more universally usable.
To avoid changing all users, we still provide some of the old definitons
defined with the help of the new macros.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Since device IDs are extremely sparse, the single, a.k.a flat table is
not sufficient for the following two reasons.
1) According to ARM-GIC spec, ITS hw can access maximum of 256(pages)*
64K(pageszie) bytes. In the best case, it supports upto DEVid=21
sparse with minimum device table entry size 8bytes.
2) The maximum memory size that is possible without memblock depends on
MAX_ORDER. 4MB on 4K page size kernel with default MAX_ORDER, so it
supports DEVid range 19bits.
The two-level device table feature brings us two advantages, the first
is a very high possibility of supporting upto 32bit sparse, and the
second one is the best utilization of memory allocation.
The feature is enabled automatically during driver probe if the memory
requirement is more than 2*ITS-pages and the hardware is capable of
two-level table walk.
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The function is getting out of control, it has too many goto
statements and would be too complicated for adding a feature
two-level device table. So, it is time for us to cleanup and
move some of the logic to a separate function without affecting
the existing functionality.
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add a platform driver to support non-root GICs that require runtime
power-management. Currently, only non-root GICs are supported because
the functions, smp_cross_call() and set_handle_irq(), that need to
be called for a root controller are located in the __init section and
so cannot be called by the platform driver.
The GIC platform driver re-uses many functions from the existing GIC
driver including some functions to save and restore the GIC context
during power transitions. The functions for saving and restoring the
GIC context are currently only defined if CONFIG_CPU_PM is enabled and
to ensure that these functions are always defined when the platform
driver is enabled, a dependency on CONFIG_ARM_GIC_PM (which selects the
platform driver) has been added.
In order to re-use the private GIC initialisation code, a new public
function, gic_of_init_child(), has been added which calls various
private functions to initialise the GIC. This is different from the
existing gic_of_init() because it only supports non-root GICs (ie. does
not call smp_cross_call() is set_handle_irq()) and is not located in
the __init section (so can be used by platform drivers). Furthermore,
gic_of_init_child() dynamically allocates memory for the GIC chip data
which is also different from gic_of_init().
There is no specific suspend handling for GICs registered as platform
devices. Non-wakeup interrupts will be disabled by the kernel during
late suspend, however, this alone will not power down the GIC if
interrupts have been requested and not freed. Therefore, requestors of
non-wakeup interrupts will need to free them on entering suspend in
order to power-down the GIC.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
To support GICs that require runtime power management, it is necessary
to add a platform driver, so that the probing of the chip can be
deferred if resources, such as a power-domain, is not yet available.
To prepare for adding a platform driver:
1. Drop the __init section from the gic_dist_config() so this can be
re-used by the platform driver.
2. Add prototypes for functions required by the platform driver to the
GIC header file so they can be re-used.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
ICC_SGI1R_AFFINITY_{2,3}_MASK are unused, which is good
because they were defined with the wrong shifts.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The INTID mask is wrong, and is made a signed value, which has
nteresting effects in the KVM emulation. Let's sanitize it.
Cc: stable@vger.kernel.org
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
(kvm_stat had nothing to do with QEMU in the first place -- the tool
only interprets debugfs)
- expose per-vm statistics in debugfs and support them in kvm_stat
(KVM always collected per-vm statistics, but they were summarised into
global statistics)
x86:
- fix dynamic APICv (VMX was improperly configured and a guest could
access host's APIC MSRs, CVE-2016-4440)
- minor fixes
ARM changes from Christoffer Dall:
"This set of changes include the new vgic, which is a reimplementation
of our horribly broken legacy vgic implementation. The two
implementations will live side-by-side (with the new being the
configured default) for one kernel release and then we'll remove the
legacy one.
Also fixes a non-critical issue with virtual abort injection to
guests."
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJXRz0KAAoJEED/6hsPKofosiMIAIHmRI+9I6VMNmQe5vrZKz9/
vt89QGxDJrFQwhEuZovenLEDaY6rMIJNguyvIbPhNuXNHIIPWbe6cO6OPwByqkdo
WI/IIqcAJN/Bpwt4/Y2977A5RwDOwWLkaDs0LrZCEKPCgeh9GWQf+EfyxkDJClhG
uIgbSAU+t+7b05K3c6NbiQT/qCzDTCdl6In6PI/DFSRRkXDaTcopjjp1PmMUSSsR
AM8LGhEzMer+hGKOH7H5TIbN+HFzAPjBuDGcoZt0/w9IpmmS5OMd3ZrZ320cohz8
zZQooRcFrT0ulAe+TilckmRMJdMZ69fyw3nzfqgAKEx+3PaqjKSY/tiEgqqDJHY=
=EEBK
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull second batch of KVM updates from Radim Krčmář:
"General:
- move kvm_stat tool from QEMU repo into tools/kvm/kvm_stat (kvm_stat
had nothing to do with QEMU in the first place -- the tool only
interprets debugfs)
- expose per-vm statistics in debugfs and support them in kvm_stat
(KVM always collected per-vm statistics, but they were summarised
into global statistics)
x86:
- fix dynamic APICv (VMX was improperly configured and a guest could
access host's APIC MSRs, CVE-2016-4440)
- minor fixes
ARM changes from Christoffer Dall:
- new vgic reimplementation of our horribly broken legacy vgic
implementation. The two implementations will live side-by-side
(with the new being the configured default) for one kernel release
and then we'll remove the legacy one.
- fix for a non-critical issue with virtual abort injection to guests"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (70 commits)
tools: kvm_stat: Add comments
tools: kvm_stat: Introduce pid monitoring
KVM: Create debugfs dir and stat files for each VM
MAINTAINERS: Add kvm tools
tools: kvm_stat: Powerpc related fixes
tools: Add kvm_stat man page
tools: Add kvm_stat vm monitor script
kvm:vmx: more complete state update on APICv on/off
KVM: SVM: Add more SVM_EXIT_REASONS
KVM: Unify traced vector format
svm: bitwise vs logical op typo
KVM: arm/arm64: vgic-new: Synchronize changes to active state
KVM: arm/arm64: vgic-new: enable build
KVM: arm/arm64: vgic-new: implement mapped IRQ handling
KVM: arm/arm64: vgic-new: Wire up irqfd injection
KVM: arm/arm64: vgic-new: Add vgic_v2/v3_enable
KVM: arm/arm64: vgic-new: vgic_init: implement map_resources
KVM: arm/arm64: vgic-new: vgic_init: implement vgic_init
KVM: arm/arm64: vgic-new: vgic_init: implement vgic_create
KVM: arm/arm64: vgic-new: vgic_init: implement kvm_vgic_hyp_init
...
Those three registers are v2 emulation specific, so their implementation
lives entirely in vgic-mmio-v2.c. Also they are handled in one function,
as their implementation is pretty simple.
When the guest enables the distributor, we kick all VCPUs to get
potentially pending interrupts serviced.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
As the GICv3 virtual interface registers differ from their GICv2
siblings, we need different handlers for processing maintenance
interrupts and reading/writing to the LRs.
Implement the respective handler functions and connect them to
existing code to be called if the host is using a GICv3.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Processing maintenance interrupts and accessing the list registers
are dependent on the host's GIC version.
Introduce vgic-v2.c to contain GICv2 specific functions.
Implement the GICv2 specific code for syncing the emulation state
into the VGIC registers.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Eric Auger <eric.auger@linaro.org>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
As (some) GICv3 hosts can emulate a GICv2, some GICv2 specific masks
for the list register definition also apply to GICv3 LRs.
At the moment we have those definitions in the KVM VGICv3
implementation, so let's move them into the GICv3 header file to
have them automatically defined.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
- x86: miscellaneous fixes, AVIC support (local APIC virtualization,
AMD version)
- s390: polling for interrupts after a VCPU goes to halted state is
now enabled for s390; use hardware provided information about facility
bits that do not need any hypervisor activity, and other fixes for
cpu models and facilities; improve perf output; floating interrupt
controller improvements.
- MIPS: miscellaneous fixes
- PPC: bugfixes only
- ARM: 16K page size support, generic firmware probing layer for
timer and GIC
Christoffer Dall (KVM-ARM maintainer) says:
"There are a few changes in this pull request touching things outside
KVM, but they should all carry the necessary acks and it made the
merge process much easier to do it this way."
though actually the irqchip maintainers' acks didn't make it into the
patches. Marc Zyngier, who is both irqchip and KVM-ARM maintainer,
later acked at http://mid.gmane.org/573351D1.4060303@arm.com
"more formally and for documentation purposes".
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJXPJjyAAoJEL/70l94x66DhioH/j4fwQ0FmfPSM9PArzaFHQdx
LNE3tU4+bobbsy1BJr4DiAaOUQn3DAgwUvGLWXdeLiOXtoWXBiFHKaxlqEsCA6iQ
xcTH1TgfxsVoqGQ6bT9X/2GCx70heYpcWG3f+zqBy7ZfFmQykLAC/HwOr52VQL8f
hUFi3YmTHcnorp0n5Xg+9r3+RBS4D/kTbtdn6+KCLnPJ0RcgNkI3/NcafTemoofw
Tkv8+YYFNvKV13qlIfVqxMa0GwWI3pP6YaNKhaS5XO8Pu16HuuF1JthJsUBDzwBa
RInp8R9MoXgsBYhLpz3jc9vWG7G9yDl5LehsD9KOUGOaFYJ7sQN+QZOusa6jFgA=
=llO5
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"Small release overall.
x86:
- miscellaneous fixes
- AVIC support (local APIC virtualization, AMD version)
s390:
- polling for interrupts after a VCPU goes to halted state is now
enabled for s390
- use hardware provided information about facility bits that do not
need any hypervisor activity, and other fixes for cpu models and
facilities
- improve perf output
- floating interrupt controller improvements.
MIPS:
- miscellaneous fixes
PPC:
- bugfixes only
ARM:
- 16K page size support
- generic firmware probing layer for timer and GIC
Christoffer Dall (KVM-ARM maintainer) says:
"There are a few changes in this pull request touching things
outside KVM, but they should all carry the necessary acks and it
made the merge process much easier to do it this way."
though actually the irqchip maintainers' acks didn't make it into the
patches. Marc Zyngier, who is both irqchip and KVM-ARM maintainer,
later acked at http://mid.gmane.org/573351D1.4060303@arm.com ('more
formally and for documentation purposes')"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (82 commits)
KVM: MTRR: remove MSR 0x2f8
KVM: x86: make hwapic_isr_update and hwapic_irr_update look the same
svm: Manage vcpu load/unload when enable AVIC
svm: Do not intercept CR8 when enable AVIC
svm: Do not expose x2APIC when enable AVIC
KVM: x86: Introducing kvm_x86_ops.apicv_post_state_restore
svm: Add VMEXIT handlers for AVIC
svm: Add interrupt injection via AVIC
KVM: x86: Detect and Initialize AVIC support
svm: Introduce new AVIC VMCB registers
KVM: split kvm_vcpu_wake_up from kvm_vcpu_kick
KVM: x86: Introducing kvm_x86_ops VCPU blocking/unblocking hooks
KVM: x86: Introducing kvm_x86_ops VM init/destroy hooks
KVM: x86: Rename kvm_apic_get_reg to kvm_lapic_get_reg
KVM: x86: Misc LAPIC changes to expose helper functions
KVM: shrink halt polling even more for invalid wakeups
KVM: s390: set halt polling to 80 microseconds
KVM: halt_polling: provide a way to qualify wakeups during poll
KVM: PPC: Book3S HV: Re-enable XICS fast path for irqfd-generated interrupts
kvm: Conditionally register IRQ bypass consumer
...
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS for 4.7. Here's the summary of
the changes:
- ATH79: Support for DTB passuing using the UHI boot protocol
- ATH79: Remove support for builtin DTB.
- ATH79: Add zboot debug serial support.
- ATH79: Add initial support for Dragino MS14 (Dragine 2), Onion Omega
and DPT-Module.
- ATH79: Update devicetree clock support for AR9132 and AR9331.
- ATH79: Cleanup the DT code.
- ATH79: Support newer SOCs in ath79_ddr_ctrl_init.
- ATH79: Fix regression in PCI window initialization.
- BCM47xx: Move SPROM driver to drivers/firmware/
- BCM63xx: Enable partition parser in defconfig.
- BMIPS: BMIPS5000 has I cache filing from D cache
- BMIPS: BMIPS: Add cpu-feature-overrides.h
- BMIPS: Add Whirlwind support
- BMIPS: Adjust mips-hpt-frequency for BCM7435
- BMIPS: Remove maxcpus from BCM97435SVMB DTS
- BMIPS: Add missing 7038 L1 register cells to BCM7435
- BMIPS: Various tweaks to initialization code.
- BMIPS: Enable partition parser in defconfig.
- BMIPS: Cache tweaks.
- BMIPS: Add UART, I2C and SATA devices to DT.
- BMIPS: Add BCM6358 and BCM63268support
- BMIPS: Add device tree example for BCM6358.
- BMIPS: Improve Improve BCM6328 and BCM6368 device trees
- Lantiq: Add support for device tree file from boot loader
- Lantiq: Allow build with no built-in DT.
- Loongson 3: Reserve 32MB for RS780E integrated GPU.
- Loongson 3: Fix build error after ld-version.sh modification
- Loongson 3: Move chipset ACPI code from drivers to arch.
- Loongson 3: Speedup irq processing.
- Loongson 3: Add basic Loongson 3A support.
- Loongson 3: Set cache flush handlers to nop.
- Loongson 3: Invalidate special TLBs when needed.
- Loongson 3: Fast TLB refill handler.
- MT7620: Fallback strategy for invalid syscfg0.
- Netlogic: Fix CP0_EBASE redefinition warnings
- Octeon: Initialization fixes
- Octeon: Add DTS files for the D-Link DSR-1000N and EdgeRouter Lite
- Octeon: Enable add Octeon-drivers in cavium_octeon_defconfig
- Octeon: Correctly handle endian-swapped initramfs images.
- Octeon: Support CN73xx, CN75xx and CN78xx.
- Octeon: Remove dead code from cvmx-sysinfo.
- Octeon: Extend number of supported CPUs past 32.
- Octeon: Remove some code limiting NR_IRQS to 255.
- Octeon: Simplify octeon_irq_ciu_gpio_set_type.
- Octeon: Mark some functions __init in smp.c
- Octeon: Octeon: Add Octeon III CN7xxx interface detection
- PIC32: Add serial driver and bindings for it.
- PIC32: Add PIC32 deadman timer driver and bindings.
- PIC32: Add PIC32 clock timer driver and bindings.
- Pistachio: Determine SoC revision during boot
- Sibyte: Fix Kconfig dependencies of SIBYTE_BUS_WATCHER.
- Sibyte: Strip redundant comments from bcm1480_regs.h.
- Panic immediately if panic_on_oops is set.
- module: fix incorrect IS_ERR_VALUE macro usage.
- module: Make consistent use of pr_*
- Remove no longer needed work_on_cpu() call.
- Remove CONFIG_IPV6_PRIVACY from defconfigs.
- Fix registers of non-crashing CPUs in dumps.
- Handle MIPSisms in new vmcore_elf32_check_arch.
- Select CONFIG_HANDLE_DOMAIN_IRQ and make it work.
- Allow RIXI to be used on non-R2 or R6 cores.
- Reserve nosave data for hibernation
- Fix siginfo.h to use strict POSIX types.
- Don't unwind user mode with EVA.
- Fix watchpoint restoration
- Ptrace watchpoints for R6.
- Sync icache when it fills from dcache
- I6400 I-cache fills from dcache.
- Various MSA fixes.
- Cleanup MIPS_CPU_* definitions.
- Signal: Move generic copy_siginfo to signal.h
- Signal: Fix uapi include in exported asm/siginfo.h
- Timer fixes for sake of KVM.
- XPA TLB refill fixes.
- Treat perf counter feature
- Update John Crispin's email address
- Add PIC32 watchdog and bindings.
- Handle R10000 LL/SC bug in set_pte()
- cpufreq: Various fixes for Longson1.
- R6: Fix R2 emulation.
- mathemu: Cosmetic fix to ADDIUPC emulation, plenty of other small fixes
- ELF: ABI and FP fixes.
- Allow for relocatable kernel and use that to support KASLR.
- Fix CPC_BASE_ADDR mask
- Plenty fo smp-cps, CM, R6 and M6250 fixes.
- Make reset_control_ops const.
- Fix kernel command line handling of leading whitespace.
- Cleanups to cache handling.
- Add brcm, bcm6345-l1-intc device tree bindings.
- Use generic clkdev.h header
- Remove CLK_IS_ROOT usage.
- Misc small cleanups.
- CM: Fix compilation error when !MIPS_CM
- oprofile: Fix a preemption issue
- Detect DSP ASE v3 support:1"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (275 commits)
MIPS: pic32mzda: fix getting timer clock rate.
MIPS: ath79: fix regression in PCI window initialization
MIPS: ath79: make ath79_ddr_ctrl_init() compatible for newer SoCs
MIPS: Fix VZ probe gas errors with binutils <2.24
MIPS: perf: Fix I6400 event numbers
MIPS: DEC: Export `ioasic_ssr_lock' to modules
MIPS: MSA: Fix a link error on `_init_msa_upper' with older GCC
MIPS: CM: Fix compilation error when !MIPS_CM
MIPS: Fix genvdso error on rebuild
USB: ohci-jz4740: Remove obsolete driver
MIPS: JZ4740: Probe OHCI platform device via DT
MIPS: JZ4740: Qi LB60: Remove support for AVT2 variant
MIPS: pistachio: Determine SoC revision during boot
MIPS: BMIPS: Adjust mips-hpt-frequency for BCM7435
mips: mt7620: fallback to SDRAM when syscfg0 does not have a valid value for the memory type
MIPS: Prevent "restoration" of MSA context in non-MSA kernels
MIPS: cevt-r4k: Dynamically calculate min_delta_ns
MIPS: malta-time: Take seconds into account
MIPS: malta-time: Start GIC count before syncing to RTC
MIPS: Force CPUs to lose FP context during mode switches
...
Provide a gic_read_local_vp_id() function to read the VCNUM field of the
GICs local VP_IDENT register. This will be used by a further patch to
check that the value reported by the GIC matches up with the kernels
calculation.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12334/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The GICv3 include file defines GICR_ISACTIVER and GICR_ICACTIVER
in the RD_base page. News flash, they do not exist (probably
a copy/paste brain fart). Just drop them.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Fill up the recently introduced gic_kvm_info with the hardware
information used for virtualization.
Signed-off-by: Julien Grall <julien.grall@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
For now, the firmware tables are parsed 2 times: once in the GIC
drivers, the other timer when initializing the vGIC. It means code
duplication and make more tedious to add the support for another
firmware table (like ACPI).
Introduce a new structure and set of helpers to get/set the virtual GIC
information. Also fill up the structure for GICv2.
Signed-off-by: Julien Grall <julien.grall@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
We've unfortunately started seeing a situation where percpu interrupts
are partitioned in the system: one arbitrary set of CPUs has an
interrupt connected to a type of device, while another disjoint
set of CPUs has the same interrupt connected to another type of device.
This makes it impossible to have a device driver requesting this interrupt
using the current percpu-interrupt abstraction, as the same interrupt number
is now potentially claimed by at least two drivers, and we forbid interrupt
sharing on per-cpu interrupt.
A solution to this is to turn things upside down. Let's assume that our
system describes all the possible partitions for a given interrupt, and
give each of them a unique identifier. It is then possible to create
a namespace where the affinity identifier itself is a form of interrupt
number. At this point, it becomes easy to implement a set of partitions
as a cascaded irqchip, each affinity identifier being the HW irq.
This allows us to keep a number of nice properties:
- Each partition results in a separate percpu-interrupt (with a restrictied
affinity), which keeps drivers happy.
- Because the underlying interrupt is still per-cpu, the overhead of
the indirection can be kept pretty minimal.
- The core code can ignore most of that crap.
For that purpose, we implement a small library that deals with some of
the boilerplate code, relying on platform-specific drivers to provide
a description of the affinity sets and a set of callbacks.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Link: http://lkml.kernel.org/r/1460365075-7316-4-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This commit does several things to avoid breaking bisectability.
1- Remove IPI init code from irqchip/mips-gic
2- Implement the new irqchip->send_ipi() in irqchip/mips-gic
3- Select GENERIC_IRQ_IPI Kconfig symbol for MIPS_GIC
4- Change MIPS SMP to use the generic IPI implementation
Only the SMP variants that use GIC were converted as it's the only irqchip that
will have the support for generic IPI for now.
Signed-off-by: Qais Yousef <qais.yousef@imgtec.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: <jason@lakedaemon.net>
Cc: <marc.zyngier@arm.com>
Cc: <jiang.liu@linux.intel.com>
Cc: <linux-mips@linux-mips.org>
Cc: <lisa.parratt@imgtec.com>
Cc: Qais Yousef <qsyousef@gmail.com>
Link: http://lkml.kernel.org/r/1449580830-23652-18-git-send-email-qais.yousef@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Linus Torvalds