-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmDGe+4eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG/IUH/iyHVulAtAhL9bnR
qL4M1kWfcG1sKS2TzGRZzo6YiUABf89vFP90r4sKxG3AKrb8YkTwmJr8B/sWwcsv
PpKkXXTobbDfpSrsXGEapBkQOE7h2w739XeXyBLRPkoCR4UrEFn68TV2rLjMLBPS
/EIZkonXLWzzWalgKDP4wSJ7GaQxi3LMx3dGAvbFArEGZ1mPHNlgWy2VokFY/yBf
qh1EZ5rugysc78JCpTqfTf3fUPK2idQW5gtHSMbyESrWwJ/3XXL9o1ET3JWURYf1
b0FgVztzddwgULoIGWLxDH5WWts3l54sjBLj0yrLUlnGKA5FjrZb12g9PdhdywuY
/8KfjeE=
=JfJm
-----END PGP SIGNATURE-----
Merge tag 'v5.13-rc6' into usb-next
We want the usb fixes in here as well, and this resolves some merge
issues with:
drivers/usb/dwc3/debugfs.c
drivers/usb/dwc3/gadget.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmDGe+4eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG/IUH/iyHVulAtAhL9bnR
qL4M1kWfcG1sKS2TzGRZzo6YiUABf89vFP90r4sKxG3AKrb8YkTwmJr8B/sWwcsv
PpKkXXTobbDfpSrsXGEapBkQOE7h2w739XeXyBLRPkoCR4UrEFn68TV2rLjMLBPS
/EIZkonXLWzzWalgKDP4wSJ7GaQxi3LMx3dGAvbFArEGZ1mPHNlgWy2VokFY/yBf
qh1EZ5rugysc78JCpTqfTf3fUPK2idQW5gtHSMbyESrWwJ/3XXL9o1ET3JWURYf1
b0FgVztzddwgULoIGWLxDH5WWts3l54sjBLj0yrLUlnGKA5FjrZb12g9PdhdywuY
/8KfjeE=
=JfJm
-----END PGP SIGNATURE-----
Merge tag 'v5.13-rc6' into tty-next
We want the tty fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit implements the complete programming sequence for ELPG
entry and exit.
1. At ELPG entry, invokes tegra_xusb_padctl_enable_phy_sleepwalk()
and tegra_xusb_padctl_enable_phy_wake() to configure XUSB PADCTL
sleepwalk and wake detection circuits to maintain USB lines level
and respond to wake events (wake-on-connect, wake-on-disconnect,
device-initiated-wake).
2. At ELPG exit, invokes tegra_xusb_padctl_disable_phy_sleepwalk()
and tegra_xusb_padctl_disable_phy_wake() to disarm sleepwalk and
wake detection circuits.
At runtime suspend, XUSB host controller can enter ELPG to reduce
power consumption. When XUSB PADCTL wake detection circuit detects
a wake event, an interrupt will be raised. xhci-tegra driver then
will invoke pm_runtime_resume() for xhci-tegra.
Runtime resume could also be triggered by protocol drivers, this is
the host-initiated-wake event. At runtime resume, xhci-tegra driver
brings XUSB host controller out of ELPG to handle the wake events.
The same ELPG enter/exit procedure will be performed for system
suspend/resume path so USB devices can remain connected across SC7.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This commit unlinks xhci-tegra platform device with SS/host power
domain devices. Reasons for this change is - at ELPG entry, PHY
sleepwalk and wake configuration need to be done before powering
down SS/host partitions, and PHY need be powered off after powering
down SS/host partitions. Sequence looks like roughly below:
tegra_xusb_enter_elpg() -> xhci_suspend()
-> enable PHY sleepwalk and wake if needed
-> power down SS/host partitions
-> power down PHY
If SS/host power domains are linked to xhci-tegra platform device, we
are not able to perform the sequence like above.
This commit introduces:
1. tegra_xusb_unpowergate_partitions() to power up SS and host
partitions together. If SS/host power domain devices are
available, it invokes pm_runtime_get_sync() to request power
driver to power up partitions; If power domain devices are not
available, tegra_powergate_sequence_power_up() will be used to
power up partitions.
2. tegra_xusb_powergate_partitions() to power down SS and host
partitions together. If SS/host power domain devices are
available, it invokes pm_runtime_put_sync() to request power
driver to power down partitions; If power domain devices are not
available, tegra_powergate_power_off() will be used to power down
partitions.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The XHCI controller is required to enter D3hot rather than D3cold for AMD
s2idle on this hardware generation.
Otherwise, the 'Controller Not Ready' (CNR) bit is not being cleared by
host in resume and eventually this results in xhci resume failures during
the s2idle wakeup.
Link: https://lore.kernel.org/linux-usb/1612527609-7053-1-git-send-email-Prike.Liang@amd.com/
Suggested-by: Prike Liang <Prike.Liang@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Cc: stable <stable@vger.kernel.org> # 5.11+
Link: https://lore.kernel.org/r/20210527154534.8900-1-mario.limonciello@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to store the dentry pointer for a debugfs file that we
only use to remove it when the device goes away. debugfs can do the
lookup for us instead, saving us some trouble, and making things smaller
overall.
Link: https://lore.kernel.org/r/20210525172534.848775-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If endpoints halts due to a stall then the dequeue pointer read from
hardware may already be set ahead of the stalled TRB.
After commit 674f8438c1 ("xhci: split handling halted endpoints into two
steps") in 5.12 xhci driver won't issue a Set TR Dequeue if hardware
dequeue pointer is already in the right place.
Turns out the "Set TR Dequeue pointer" command is anyway needed as it in
addition to moving the dequeue pointer also clears endpoint state and
cache.
Fixes: 674f8438c1 ("xhci: split handling halted endpoints into two steps")
Cc: <stable@vger.kernel.org> # 5.12
Reported-by: Peter Ganzhorn <peter.ganzhorn@googlemail.com>
Tested-by: Peter Ganzhorn <peter.ganzhorn@googlemail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210525074100.1154090-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
5.12 kernel changes how xhci handles cancelled URBs and halted
endpoints. Among these changes cancelled and stalled URBs are no longer
given back before they are cleared from xHC hardware cache.
These changes unfortunately cleared the -EPIPE status of a stalled
transfer in one case before giving bak the URB, causing a USB card reader
to fail from working.
Fixes: 674f8438c1 ("xhci: split handling halted endpoints into two steps")
Cc: <stable@vger.kernel.org> # 5.12
Reported-by: Peter Ganzhorn <peter.ganzhorn@googlemail.com>
Tested-by: Peter Ganzhorn <peter.ganzhorn@googlemail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210525074100.1154090-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e6604a7fd7 ("EHCI: Quirk flag for port power handling
on overcurrent.") activated the quirks handling (flag need_oc_pp_cycle)
for Freescale 83xx based boards.
Activate same for 85xx based boards as well.
Cc: xe-linux-external@cisco.com
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Gopalakrishnan Santhanam <gsanthan@cisco.com>
Signed-off-by: Daniel Walker <danielwa@cisco.com>
Link: https://lore.kernel.org/r/20210513083225.68912-1-gsanthan@cisco.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use %ptTs instead of open coded variant to print contents
of time64_t type in human readable form.
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20210511153958.34527-4-andriy.shevchenko@linux.intel.com
tty_operations::chars_in_buffer is another hook which is expected to
return values >= 0. So make it explicit by the return type too -- use
unsigned int.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-By: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Acked-by: David Sterba <dsterba@suse.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Cc: Jens Taprogge <jens.taprogge@taprogge.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: David Lin <dtwlin@gmail.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Alex Elder <elder@kernel.org>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Link: https://lore.kernel.org/r/20210505091928.22010-27-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Line disciplines expect a positive value or zero returned from
tty->ops->write_room (invoked by tty_write_room). So make this
assumption explicit by using unsigned int as a return value. Both of
tty->ops->write_room and tty_write_room.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Acked-by: Alex Elder <elder@linaro.org>
Acked-by: Max Filippov <jcmvbkbc@gmail.com> # xtensa
Acked-by: David Sterba <dsterba@suse.com>
Acked-By: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Chris Zankel <chris@zankel.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Cc: Jens Taprogge <jens.taprogge@taprogge.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Scott Branden <scott.branden@broadcom.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: David Lin <dtwlin@gmail.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Link: https://lore.kernel.org/r/20210505091928.22010-23-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is needed at USB Certification test for Embedded Host 2.0, and
the detail is at CH6.4.1.1 of On-The-Go and Embedded Host Supplement
to the USB Revision 2.0 Specification. Since other USB 2.0 capable
host like XHCI also need it, so move it to HCD core.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Link: https://lore.kernel.org/r/1620452039-11694-1-git-send-email-jun.li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One of AMD xhci controller require reset on resume.
Occasionally AMD xhci controller does not respond to
Stop endpoint command.
Once the issue happens controller goes into bad state
and in that case controller needs to be reset.
Cc: <stable@vger.kernel.org>
Signed-off-by: Sandeep Singh <sandeep.singh@amd.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210512080816.866037-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some devices (specifically the SC8180x based Surface Pro X with
QCOM04A6) HC halt / xhci_halt() times out during boot. Manually binding
the xhci-hcd driver at some point later does not exhibit this behavior.
To work around this, double XHCI_MAX_HALT_USEC, which also resolves this
issue.
Cc: <stable@vger.kernel.org>
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210512080816.866037-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'xhci_urb_enqueue()' is passed a 'mem_flags' argument, because "URBs may be
submitted in interrupt context" (see comment related to 'usb_submit_urb()'
in 'drivers/usb/core/urb.c')
So this flag should be used in all the calling chain.
Up to now, 'xhci_check_maxpacket()' which is only called from
'xhci_urb_enqueue()', uses GFP_KERNEL.
Be safe and pass the mem_flags to this function as well.
Fixes: ddba5cd0ae ("xhci: Use command structures when queuing commands on the command ring")
Cc: <stable@vger.kernel.org>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210512080816.866037-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 9ebf300078 ("xhci: Fix halted endpoint at stop endpoint command
completion") in 5.12 changes how cancelled URBs are given back.
To cancel a URB xhci driver needs to stop the endpoint first.
To clear a halted endpoint xhci driver needs to reset the endpoint.
In rare cases when an endpoint halt (error) races with a endpoint stop we
need to clear the reset before removing, and giving back the cancelled URB.
The above change in 5.12 takes care of this, but it also relies on the
reset endpoint completion handler to give back the cancelled URBs.
There are cases when driver refuses to queue reset endpoint commands,
for example when a link suddenly goes to an inactive error state.
In this case the cancelled URB is never given back.
Fix this by giving back the URB in the stop endpoint if queuing a reset
endpoint command fails.
Fixes: 9ebf300078 ("xhci: Fix halted endpoint at stop endpoint command completion")
CC: <stable@vger.kernel.org> # 5.12
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210512080816.866037-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the same way as Intel Tiger Lake TCSS (Type-C Subsystem) the Alder Lake
TCSS xHCI needs to be runtime suspended whenever possible to allow the
TCSS hardware block to enter D3cold and thus save energy.
Cc: stable@vger.kernel.org
Signed-off-by: Abhijeet Rao <abhijeet.rao@intel.com>
Signed-off-by: Nikunj A. Dadhania <nikunj.dadhania@intel.com>
Signed-off-by: Azhar Shaikh <azhar.shaikh@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210512080816.866037-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use first-fit instead of best-fit for LS/FS devices under TT,
we found that best-fit will consume more bandwidth for some
cases.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20210507021127.54717-4-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use bitfield instead of bool in struct
Refer to coding-style.rst 17) Using bool:
"If a structure has many true/false values, consider consolidating
them into a bitfield with 1 bit members, or using an appropriate
fixed width type, such as u8."
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20210507021127.54717-1-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'retval' is known to be -ENODEV here.
This is a hard-coded default error code which is not useful in the error
message. Moreover, another error message is printed at the end of the
error handling path. The corresponding error code (-ENOMEM) is more
informative.
So remove simplify the first error message.
While at it, also remove the useless initialization of 'retval'.
Fixes: 7d50195f6c ("usb: host: Faraday fotg210-hcd driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/94531bcff98e46d4f9c20183a90b7f47f699126c.1620333419.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PM will take care of the status of child device, so no need
check each port anymore.
Suggested-by: Ikjoon Jang <ikjn@chromium.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1618555706-6810-1-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A dedicated wakeup irq will be used to handle runtime suspend/resume,
we use dev_pm_set_dedicated_wake_irq API to take care of requesting
and attaching wakeup irq, then the suspend/resume framework will help
to enable/disable wakeup irq.
The runtime PM is default off since some platforms may not support it.
users can enable it via power/control (set "auto") in sysfs.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1618031406-15347-3-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kunpeng920's EHCI controller does not have SBRN register.
Reading the SBRN register when the controller driver is
initialized will get 0.
When rebooting the EHCI driver, ehci_shutdown() will be called.
if the sbrn flag is 0, ehci_shutdown() will return directly.
The sbrn flag being 0 will cause the EHCI interrupt signal to
not be turned off after reboot. this interrupt that is not closed
will cause an exception to the device sharing the interrupt.
Therefore, the EHCI controller of Kunpeng920 needs to skip
the read operation of the SBRN register.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Longfang Liu <liulongfang@huawei.com>
Link: https://lore.kernel.org/r/1617958081-17999-1-git-send-email-liulongfang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mutex lock can be initialized automatically with DEFINE_MUTEX()
rather than explicitly calling mutex_init().
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Link: https://lore.kernel.org/r/20210405101434.14878-1-zhengyongjun3@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The same values are parsed several times from transfer and event
TRBs by different functions in the same call path, all while processing
one transfer event.
As the TRBs are in DMA memory and can be accessed by the xHC host we want
to avoid this to prevent double-fetch issues.
To resolve this pass the already parsed values to the different functions
in the path of parsing a transfer event
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210406070208.3406266-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Max Interrupters supported by the controller is given in a 10bit
wide bitfield, but the driver uses a fixed 128 size array to index these
interrupters.
Klockwork reports a possible array out of bounds case which in theory
is possible. In practice this hasn't been hit as a common number of Max
Interrupters for new controllers is 8, not even close to 128.
This needs to be fixed anyway
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210406070208.3406266-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xHCI driver support usb2 HW LPM by default, here add support
XHCI_HW_LPM_DISABLE quirk, then we can disable usb2 lpm when
need it.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1617181553-3503-4-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MediaTek 0.96 xHCI controller on some platforms does not
support bulk stream even HCCPARAMS says supporting, due to MaxPSASize
is set a default value 1 by mistake, here use XHCI_BROKEN_STREAMS
quirk to fix it.
Fixes: 94a631d91a ("usb: xhci-mtk: check hcc_params after adding primary hcd")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1617181553-3503-3-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The oops happens when unbind driver through sysfs as following,
because xhci_mtk_drop_ep() try to drop the endpoint of root hub
which is not added by xhci_add_endpoint() and the virtual device
is not allocated, in fact also needn't drop it, so should skip it.
Call trace:
xhci_mtk_drop_ep+0x1b8/0x298
usb_hcd_alloc_bandwidth+0x1d8/0x380
usb_disable_device_endpoints+0x8c/0xe0
usb_disable_device+0x128/0x168
usb_disconnect+0xbc/0x2c8
usb_remove_hcd+0xd8/0x210
xhci_mtk_remove+0x98/0x108
platform_remove+0x28/0x60
device_release_driver_internal+0x110/0x1e8
device_driver_detach+0x18/0x28
unbind_store+0xd4/0x108
drv_attr_store+0x24/0x38
Fixes: 14295a1500 ("usb: xhci-mtk: support to build xhci-mtk-hcd.ko")
Reported-by: Eddie Hung <eddie.hung@mediatek.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1617179142-2681-2-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The remainder of the last bandwidth bugdget is wrong,
it's the value alloacted in last bugdget, not unused.
Reported-by: Yaqii Wu <Yaqii.Wu@mediatek.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1617179142-2681-1-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support ip-sleep wakeup for MT8183, it's similar to MT8173,
and it's also a specific one, but not following IPM rule.
Due to the index 2 already used by many DTS, it's better to keep
it unchanged for backward compatibility, treat specific ones without
following IPM rule as revision 1.x, meanwhile reserve 3~10 for
later revision that follows the IPM rule.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1616482975-17841-6-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current xhci_create_usb3_bos_desc() uses a static bos u8 array and
various magic numbers and offsets making it difficult to extend support
for USB 3.2. Let's rewrite this entire function to support dual-lane in
USB 3.2.
The hub driver matches the port speed ID from the extended port status
to the SSID of the sublink speed attributes to detect if the device
supports SuperSpeed Plus. Currently we don't provide the default gen1x2
and gen2x2 sublink speed capability descriptor for USB 3.2 roothub. The
USB stack depends on this to detect and match the correct speed.
In addition, if the xHCI host provides Protocol Speed ID (PSI)
capability, then make sure to convert Protocol Speed ID Mantissa and
Exponent (PSIM & PSIE) to lane speed for gen1x2 and gen2x2.
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/19cd09b03f96346996270579fd27d38b8a6844aa.1615432770.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some hosts incorrectly use sub-minor version for minor version (i.e.
0x02 instead of 0x20 for bcdUSB 0x320 and 0x01 for bcdUSB 0x310).
Currently the xHCI driver works around this by just checking for minor
revision > 0x01 for USB 3.1 everywhere. With the addition of USB 3.2,
checking this gets a bit cumbersome. Since there is no USB release with
bcdUSB 0x301 to 0x309, we can assume that sub-minor version 01 to 09 is
incorrect. Let's try to fix this and use the minor revision that matches
with the USB/xHCI spec to help with the version checking within the
driver.
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/ed330e95a19dc367819c5b4d78bf7a541c35aa0a.1615432770.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Force-threaded interrupt handlers used to run with interrupts enabled,
something which could lead to deadlocks in case a threaded handler
shared a lock with code running in hard interrupt context (e.g. timer
callbacks) and did not explicitly disable interrupts.
Since commit 81e2073c17 ("genirq: Disable interrupts for force
threaded handlers") interrupt handlers always run with interrupts
disabled on non-RT so that drivers no longer need to do handle forced
threading ("threadirqs").
Drop the now obsolete workaround added by commit 63aea0dbab ("USB:
xhci: fix lock-inversion problem").
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210322111140.32056-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A space was given after tab key. The extra space has been removed.
This is done to maintain uniformity in the code.
Signed-off-by: Shubhankar Kuranagatti <shubhankarvk@gmail.com>
Link: https://lore.kernel.org/r/20210311190058.yudmivcbok56itay@kewl-virtual-machine
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gcc-11 now warns about a confusingly indented code block:
drivers/usb/host/sl811-hcd.c: In function ‘sl811h_hub_control’:
drivers/usb/host/sl811-hcd.c:1291:9: error: this ‘if’ clause does not guard... [-Werror=misleading-indentation]
1291 | if (*(u16*)(buf+2)) /* only if wPortChange is interesting */
| ^~
drivers/usb/host/sl811-hcd.c:1295:17: note: ...this statement, but the latter is misleadingly indented as if it were guarded by the ‘if’
1295 | break;
Rewrite this to use a single if() block with the __is_defined() macro.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210322164244.827589-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Force-threaded interrupt handlers used to run with interrupts enabled,
something which could lead to deadlocks in case a threaded handler
shared a lock with code running in hard interrupt context (e.g. timer
callbacks) and did not explicitly disable interrupts.
Since commit 81e2073c17 ("genirq: Disable interrupts for force
threaded handlers") interrupt handlers always run with interrupts
disabled on non-RT so that drivers no longer need to do handle forced
threading ("threadirqs").
Drop the now obsolete workaround added by commit a1227f3c10 ("usb:
ehci: fix deadlock when threadirqs option is used").
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210322111249.32141-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Select USB_GADGET Kconfig option in order to fix build failure which
happens because ChipIdea driver has a build dependency on both USB_GADGET
and USB_EHCI_HCD, while USB_EHCI_TEGRA force-selects the ChipIdea driver
without taking into account the tristate USB_GADGET dependency. It's not
possible to do anything about the cyclic dependency of the Kconfig
options, but USB_EHCI_TEGRA is now a deprecated option that isn't used
by defconfigs and USB_GADGET is wanted on Tegra by default, hence it's
okay to have a bit clunky workaround for it.
Fixes: c3590c7656 ("usb: host: ehci-tegra: Remove the driver")
Reported-by: kernel test robot <lkp@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210320151915.7566-2-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Over-current reporting isn't supported on some platforms such as bcm63xx.
These devices will incorrectly report over-current if this flag isn't properly
activated.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Link: https://lore.kernel.org/r/20210223174455.1378-4-noltari@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds an ignore_oc flag which can be set by EHCI controller
not supporting or wanting to disable overcurrent checking. The EHCI
platform data in include/linux/usb/ehci_pdriver.h is also augmented to
take advantage of this new flag.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Link: https://lore.kernel.org/r/20210223174455.1378-2-noltari@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If port terminations are detected in suspend, but link never reaches U0
then xHCI may have an internal uncleared wake state that will cause an
immediate wake after suspend.
This wake state is normally cleared when driver clears the PORT_CSC bit,
which is set after a device is enabled and in U0.
Write 1 to clear PORT_CSC for ports that don't have anything connected
when suspending. This makes sure any pending internal wake states in
xHCI are cleared.
Cc: stable@vger.kernel.org
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210311115353.2137560-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I've confirmed that both the ASMedia ASM1042A and ASM3242 have the same
problem as the ASM1142 and ASM2142/ASM3142, where they lose some of the
upper bits of 64-bit DMA addresses. As with the other chips, this can
cause problems on systems where the upper bits matter, and adding the
XHCI_NO_64BIT_SUPPORT quirk completely fixes the issue.
Cc: stable@vger.kernel.org
Signed-off-by: Forest Crossman <cyrozap@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210311115353.2137560-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A xHC USB 3 port might miss the first wake signal from a USB 3 device
if the port LFPS reveiver isn't enabled fast enough after xHC resume.
xHC host will anyway be resumed by a PME# signal, but will go back to
suspend if no port activity is seen.
The device resends the U3 LFPS wake signal after a 100ms delay, but
by then host is already suspended, starting all over from the
beginning of this issue.
USB 3 specs say U3 wake LFPS signal is sent for max 10ms, then device
needs to delay 100ms before resending the wake.
Don't suspend immediately if port activity isn't detected in resume.
Instead add a retry. If there is no port activity then delay for 120ms,
and re-check for port activity.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210311115353.2137560-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some systems rt2800usb and mt7601u devices are unable to operate since
commit f8f80be501 ("xhci: Use soft retry to recover faster from
transaction errors")
Seems that some xHCI controllers can not perform Soft Retry correctly,
affecting those devices.
To avoid the problem add xhci->quirks flag that restore pre soft retry
xhci behaviour for affected xHCI controllers. Currently those are
AMD_PROMONTORYA_4 and AMD_PROMONTORYA_2, since it was confirmed
by the users: on those xHCI hosts issue happen and is gone after
disabling Soft Retry.
[minor commit message rewording for checkpatch -Mathias]
Fixes: f8f80be501 ("xhci: Use soft retry to recover faster from transaction errors")
Cc: <stable@vger.kernel.org> # 4.20+
Reported-by: Bernhard <bernhard.gebetsberger@gmx.at>
Tested-by: Bernhard <bernhard.gebetsberger@gmx.at>
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=202541
Link: https://lore.kernel.org/r/20210311115353.2137560-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently xhci-hcd.ko building depends on USB_XHCI_MTK, this
is not flexible for some cases. For example:
USB_XHCI_HCD is y, and USB_XHCI_MTK is m, then we can't
implement extended functions if only update xhci-mtk.ko
This patch is used to remove the dependence.
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/0b62e21ddfacc1c2874726dd27ccab80c993f303.1615170625.git.chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the LS/FS device is connected to an external HS hub, the member
@tt_info in xhci_virt_device struct in not NULL, use it to check
whether a LS/FS device is under an exernal HS hub, then no need get
the slot context of this device.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/8117df52f16bd03087e486d7d740a183b6dd634a.1615170625.git.chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In USB2 Spec:
"11.18.5 TT Response Generation
In general, there will be two (or more) complete-split
transactions scheduled for a periodic endpoint.
However, for interrupt endpoints, the maximum size of
the full-/low-speed transaction guarantees that it can
never require more than two complete-split transactions.
Two complete-split transactions are only required
when the transaction spans a microframe boundary."
Due to the maxp is 64, and less then 188 (at most in one
microframe), seems never span boundary, so use only one CS
for FS/LS interrupt transfer, this will save some bandwidth.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/5b9ff09f53d23cf9e5c5437db4ffc18b798bf60c.1615170625.git.chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the USB headset is plug into an external hub, sometimes
can't set config due to not enough bandwidth, so need improve
LS/FS INT/ISOC bandwidth scheduling with TT.
Fixes: 54f6a8af37 ("usb: xhci-mtk: skip dropping bandwidth of unchecked endpoints")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Yaqii Wu <yaqii.wu@mediatek.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/2f30e81400a59afef5f8231c98149169c7520519.1615170625.git.chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Side effect may happen if use or operator to set schedule parameters
when the parameters are already set before. Set them directly due to
other bits are reserved.
Fixes: 54f6a8af37 ("usb: xhci-mtk: skip dropping bandwidth of unchecked endpoints")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/d287899e6beb2fc1bfb8900c75a872f628ecde55.1615170625.git.chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to keep the dentry pointer around for the created
debugfs file, as it is only needed when removing it from the system.
When it is to be removed, ask debugfs itself for the pointer, to save on
storage and make things a bit simpler.
And, no one noticed that a __maybe_unused dentry * in uhci_start()
really was unused, so remove that as it's obviously not needed, and
hasn't been for quite some time.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: linux-usb@vger.kernel.org
Link: https://lore.kernel.org/r/20210216144645.3813043-4-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to keep the dentry pointer around for the created
debugfs file, as it is only needed when removing it from the system.
When it is to be removed, ask debugfs itself for the pointer, to save on
storage and make things a bit simpler.
Cc: linux-usb@vger.kernel.org
Link: https://lore.kernel.org/r/20210216144645.3813043-3-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to keep the dentry pointer around for the created
debugfs file, as it is only needed when removing it from the system.
When it is to be removed, ask debugfs itself for the pointer, to save on
storage and make things a bit simpler.
Cc: linux-usb@vger.kernel.org
Link: https://lore.kernel.org/r/20210216144645.3813043-2-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to keep the dentry pointer around for the created
debugfs file, as it is only needed when removing it from the system.
When it is to be removed, ask debugfs itself for the pointer, to save on
storage and make things a bit simpler.
Cc: Olav Kongas <ok@artecdesign.ee>
Cc: linux-usb@vger.kernel.org
Link: https://lore.kernel.org/r/20210216144645.3813043-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Generalise byte swapping assembly
- Update debug addresses for STI
- Validate start of physical memory with DTB
- Do not clear SCTLR.nTLSMD in decompressor
- amba/locomo/sa1111 devices remove method return type is void
- address markers for KASAN in page table dump
-----BEGIN PGP SIGNATURE-----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=BULT
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM updates from Russell King:
- Generalise byte swapping assembly
- Update debug addresses for STI
- Validate start of physical memory with DTB
- Do not clear SCTLR.nTLSMD in decompressor
- amba/locomo/sa1111 devices remove method return type is void
- address markers for KASAN in page table dump
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 9065/1: OABI compat: fix build when EPOLL is not enabled
ARM: 9055/1: mailbox: arm_mhuv2: make remove callback return void
amba: Make use of bus_type functions
amba: Make the remove callback return void
vfio: platform: simplify device removal
amba: reorder functions
amba: Fix resource leak for drivers without .remove
ARM: 9054/1: arch/arm/mm/mmu.c: Remove duplicate header
ARM: 9053/1: arm/mm/ptdump:Add address markers for KASAN regions
ARM: 9051/1: vdso: remove unneded extra-y addition
ARM: 9050/1: Kconfig: Select ARCH_HAVE_NMI_SAFE_CMPXCHG where possible
ARM: 9049/1: locomo: make locomo bus's remove callback return void
ARM: 9048/1: sa1111: make sa1111 bus's remove callback return void
ARM: 9047/1: smp: remove unused variable
ARM: 9046/1: decompressor: Do not clear SCTLR.nTLSMD for ARMv7+ cores
ARM: 9045/1: uncompress: Validate start of physical memory against passed DTB
ARM: 9042/1: debug: no uncompress debugging while semihosting
ARM: 9041/1: sti LL_UART: add STiH418 SBC UART0 support
ARM: 9040/1: use DEBUG_UART_PHYS and DEBUG_UART_VIRT for sti LL_UART
ARM: 9039/1: assembler: generalize byte swapping macro into rev_l
This replaces the platform_device_add_properties() call with
the safer device_create_managed_software_node() that does
exactly the same, but can also guarantee that the lifetime
of the node that is created for the device is tied to the
lifetime of device itself.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20210204141711.53775-7-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci driver may in some special cases need to copy small amounts
of payload data to a bounce buffer in order to meet the boundary
and alignment restrictions set by the xHCI specification.
In the majority of these cases the data is in a sg list, and
driver incorrectly assumed data is always in urb->sg when using
the bounce buffer.
If data instead is contiguous, and in urb->transfer_buffer, we may still
need to bounce buffer a small part if data starts very close (less than
packet size) to a 64k boundary.
Check if sg list is used before copying data to/from it.
Fixes: f9c589e142 ("xhci: TD-fragment, align the unsplittable case with a bounce buffer")
Cc: stable@vger.kernel.org
Reported-by: Andreas Hartmann <andihartmann@01019freenet.de>
Tested-by: Andreas Hartmann <andihartmann@01019freenet.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210203113702.436762-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Older ATF does not provide SMC call for USB 3.0 phy power on functionality
and therefore initialization of xhci-hcd is failing when older version of
ATF is used. In this case phy_power_on() function returns -EOPNOTSUPP.
[ 3.108467] mvebu-a3700-comphy d0018300.phy: unsupported SMC call, try updating your firmware
[ 3.117250] phy phy-d0018300.phy.0: phy poweron failed --> -95
[ 3.123465] xhci-hcd: probe of d0058000.usb failed with error -95
This patch introduces a new plat_setup callback for xhci platform drivers
which is called prior calling usb_add_hcd() function. This function at its
beginning skips PHY init if hcd->skip_phy_initialization is set.
Current init_quirk callback for xhci platform drivers is called from
xhci_plat_setup() function which is called after chip reset completes.
It happens in the middle of the usb_add_hcd() function and therefore this
callback cannot be used for setting if PHY init should be skipped or not.
For Armada 3720 this patch introduce a new xhci_mvebu_a3700_plat_setup()
function configured as a xhci platform plat_setup callback. This new
function calls phy_power_on() and in case it returns -EOPNOTSUPP then
XHCI_SKIP_PHY_INIT quirk is set to instruct xhci-plat to skip PHY
initialization.
This patch fixes above failure by ignoring 'not supported' error in
xhci-hcd driver. In this case it is expected that phy is already power on.
It fixes initialization of xhci-hcd on Espressobin boards where is older
Marvell's Arm Trusted Firmware without SMC call for USB 3.0 phy power.
This is regression introduced in commit bd3d25b073 ("arm64: dts: marvell:
armada-37xx: link USB hosts with their PHYs") where USB 3.0 phy was defined
and therefore xhci-hcd on Espressobin with older ATF started failing.
Fixes: bd3d25b073 ("arm64: dts: marvell: armada-37xx: link USB hosts with their PHYs")
Cc: <stable@vger.kernel.org> # 5.1+: ea17a0f153af: phy: marvell: comphy: Convert internal SMCC firmware return codes to errno
Cc: <stable@vger.kernel.org> # 5.1+: f768e718911e: usb: host: xhci-plat: add priv quirk for skip PHY initialization
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> # On R-Car
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> # xhci-plat
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20210201150803.7305-1-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No need to check the following endpoints after finding the endpoint
wanted to drop.
Fixes: 54f6a8af37 ("usb: xhci-mtk: skip dropping bandwidth of unchecked endpoints")
Cc: stable <stable@vger.kernel.org>
Reported-by: Ikjoon Jang <ikjn@chromium.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1612255104-5363-1-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver core ignores the return value of struct device_driver::remove
because there is only little that can be done. To simplify the quest to
make this function return void, let struct sa1111_driver::remove return
void, too. All users already unconditionally return 0, this commit makes
it obvious that returning an error code is a bad idea and ensures future
users behave accordingly.
Link: https://lore.kernel.org/r/20201126114724.2028511-1-u.kleine-koenig@pengutronix.de
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
For those unchecked endpoints, we don't allocate bandwidth for
them, so no need free the bandwidth, otherwise will decrease
the allocated bandwidth.
Meanwhile use xhci_dbg() instead of dev_dbg() to print logs and
rename bw_ep_list_new as bw_ep_chk_list.
Fixes: 1d69f9d901 ("usb: xhci-mtk: fix unreleased bandwidth data")
Cc: stable <stable@vger.kernel.org>
Reviewed-and-tested-by: Ikjoon Jang <ikjn@chromium.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1612159064-28413-1-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we receive a transfer event indicating that an endpoint should be
halted, but current endpoint state doesn't match it, then the halt might
be just resolved by the stop endpoint completion handler that detects the
halted endpoint due to a context state error.
In this case the TD we halted on is already moved to the cancelled TD list,
and should not be successfully completed and given back anymore.
Let the stop endpoint completion handler reset the endpoint, and then let
the reset endpoint handler give back the cancelled TD among all other
ones on the cancelled TD list
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-28-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A halted endpoint can be detected both when transfer events complete, and
in stop endpoint command completion. Both these handlers will start
clearing up the halted endpoint and queue a reset endpoint command.
It's possible to get both events for the same halted endpoint if right
after a URB cancel queues a stop endpoint command the endpoint stalls.
Use the EP_HALTED flag to prevent resetting the endpoint twice.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-27-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_find_new_dequeue_state() and xhci_queue_new_dequeue_state() are no
longer used afer introducing the move_dequeue_past_td() function.
also remove struct xhci_dequeue_state as its no longer used.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-26-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace xhci_find_new_dequeue_state() and xhci_queue_new_dequeue_state()
functions with one combined function.
These function were always called after each other, and had a lot of extra
code just to pass the newly found dequeue state from the first function
to the other.
The new function also returns error in case there is a failure to
queue the new dequeue state. This way the caller can decide on
recovery measures to handle it.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-25-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Handle race where a stop endpoint command fails with "context state error"
as hardware hasn't actually started the ring yet after a previous urb
cancellation completed and restarted the endpoint.
Flushing the doorbell write that restart the endpoint reduced these cases,
but didn't completely resolve them.
Check if the ring is running in the stop endpoint completion handler, and
issue a new stop endpoint command in this case.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-24-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci 4.6.9: "A busy endpoint may asynchronously transition from the
Running to the Halted or Error state due to error conditions detected
while processing TRBs. A possible race condition may occur if software,
thinking an endpoint is in the running state, issues a Stop Endpoint
Command, however at the same time the xHC asynchronously transitions
the endpoint to the Halted or Error state. In this case, a Context
State Error may be generated for the command completion. Software
may verify that this case occurred by inspecting the EP State for
Halted or Error when a Stop Endpoint Command results in a Context
State Error."
Halted endpoints were not detected or handled at all in the stop endpoint
completion handler. A set TR Deq ptr command was bluntly queued instead
of resetting the endpoint first. The set TR Deq command would fail with
a context state error.
Fix this case by resetting the halted endpoint first to get it to a
stopped state instead of the halted (error) state.
Handle cancelled TDs once endpoint reset completes,
invalidating cancelled TDs on ring either by turning them to no-op,
or in case ring stopped on cancelled TD then move hardware dequeue pointer
past it, which will clear the cancelled TD from hw cache, and make sure
HW does not process it
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-23-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't queue both a reset endpoint command and a
set TR deq command at once when handling a halted endpoint.
split this into two steps.
Initially only queue a reset endpoint command, and then if needed queue a
set TR deq command in the reset endpoint handler.
Note: This removes the RESET_EP_QUIRK handling which was added in
commit ac9d8fe7c6 ("USB: xhci: Add quirk for Fresco Logic xHCI hardware.")
This quirk was added in 2009 for prototype xHCI hardware meant for
evaluation purposes only, and should not reach consumers.
This hardware could not handle two commands queued at once, and had
bad data in the output context after a reset endpoint command.
After this patch two command are no longer queued at once, so that
part is solved in this rewrite, but the workaround for bad data in the
output context solved by issuing an extra configure endpoint command is
bluntly removed.
Adding this workaround to the new rewrite just adds complexity, and I
think it's time to let this quirk go.
Print a debug message instead.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-22-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Halted endpoints can be discoverd both when handling transfer events and
command completion events. Move code that handles halted endpoints before
both of those event handlers.
Rename the function to xhci_handle_halted_ep() to better describe
what it does. Try to reserve "cleanup" word in function names for last
stage cleanup activities.
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-21-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor handler for stop endpoint command completion. Yank out the part
that invalidates cancelled TDs and turn it into a separate function.
Invalidating cancelled TDs should be done while the ring is stopped,
but not exclusively in the stop endpoint command completeion handler.
We will need to invalidate TDs after resetting endpoints as well.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-20-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In cases where the TD can't be given back in current handler we want
to be able to store it until its time to return the TD.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-19-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
use the existing xhci_td_cleanup() to give back cancelled TDs when a
ring is stopped.
A minor change to make sure we don't try to remove an already removed
td from the list is needed as cancelled TDs are already removed from the
td_list immediatelty when it's cancelled.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-18-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Create a separate helper function to issue reset endpont commands
to clear halted endpoints.
This is useful for cases where a halted endpoint is discovered while
completing another command, and the endpoint halt needs to be cleared
with a endpoint reset first.
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-16-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stop endpoint command fails with "context state error" if the endpoint is
already stopped.
This case was observed when a previous URB cancel had just completed and
rang the doorbell to restart the ring, when a new URB cancel queued a stop
endpoint command.
>From xHC hardware pov the endpoint had not yet started, so the stop
endpoint command failed with context state error.
Right after this the doorbell ring took effect and ring was restarted.
Interrupt handler saw a stop endpoint command completion event with
"context state error" and discovered that the ring was back up in
running state.
flushing the write reduces these cases in stress testing, but does not
completely remove the issue.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-15-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci driver relies on link TRBs existing in the correct places in TRB
ring buffers shared with the host controller.
The controller should not modify these link TRBs, but in theory a faulty
xHC could do it.
Add some basic sanity checks to avoid infinite loops in interrupt handler,
or accessing unallocated memory outside a ring segment due to missing or
misplaced link TRBs.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-14-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of re-reading, masking and endianness correcting the same trb
several times to get the trb type from an event, just do it once and
store it in a local variable.
Also pass the trb_type directly to the vendor specific event handler,
avoiding one more similar read.
In addition to the security benefit this also cleans up the code
and helps readability.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-13-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When finishing a TD we walk the endpoint dequeue trb pointer
until it matches the last TRB of the TD.
TDs can contain over 100 TRBs, meaning we call a function 100 times,
do a few comparisons and increase a couple values for each of these calls,
all in interrupt context.
This can all be avoided by adding a pointer to the last TRB segment, and
a number of TRBs in the TD. So instead of walking through each TRB just
set the new dequeue segment, pointer, and number of free TRBs directly.
Getting rid of the while loop also reduces the risk of getting stuck in a
infinite loop in the interrupt handler. Loop relied on valid matching
dequeue and last_trb values to break.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-12-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check that the slot_id that we dug out from command completion event
TRB, is valid before using it to identify the slot associated with the
command that generated the event.
Signed-off-by: Lalithambika Krishna Kumar <lalithambika.krishnakumar@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-11-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci driver links together segments in a ring buffer by turning the last
TRB of a segment into a link TRB, pointing to the beginning of
the next segment.
If the first TRB of every segment for some unknown reason is a link TRB
pointing to the next segment, then prepare_ring() loops indefinitely.
This isn't something the xhci driver would do.
xHC hardware has access to these rings, it sholdn't be writing link
TRBs either, but with broken xHC hardware this could in theory be
possible.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-10-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The one case that used this function can use the
xhci_triad_to_transfer_ring() helper instead.
Avoid having several functions doing basically the same thing.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-9-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Two existing ring helpers, xhci_triad_to_transfer_ring() and
xhci_stream_id_to_ring() have partially similar functionality.
Both have some limitation, especieally with boundary checking.
Add a new xhci_virt_ep_to_ring() helper with proper boundary checking
that can replace parts of one helper, and later will completely
replace the other helper.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check that the xhci_virt_dev structure that we dug out based
on a slot_id value from a command completion is valid before
dereferencing it.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In several event handlers we need to find the right endpoint
structure from slot_id and ep_index in the event.
Add a helper for this, check that slot_id and ep_index are valid.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
several command completion handlers are passed the event trb
as a paramtere even if it't not used.
Remove it.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of passing slot id and endpoint index to
cleanup_halted_endpoint() pass the endpoint structure pointer
as it's already known.
Avoids again digging out the endpoint structure based on
slot id and endpoint index, and passing them along the
call chain for this purpose only.
Add slot_id to the virt_dev structure so that it
can easily be found from a virt_dev, or its child, the
virt_ep endpoint structure.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
isochronous endpoints do not support streams, meaning that
there is only one ring per endpoint.
Avoid double-fetching the transfer event DMA to get the
ring. Also makes passing the event to skip_isoc_td() uncecessary.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When handling transfer events the event is passed along the handling
callpath and parsed again in several occasions.
The event contains slot_id and endpoint index, from which the driver
endpoint structure can be found. There wasn't however a way to get the
endpoint index or parent usb device from this endpoint structure.
A lot of extra event parsing, and thus some DMA doublefetch cases,
and excess variables and code can be avoided by adding endpoint index
and parent usb virt device pointer to the endpoint structure.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci-mtk needs XHCI_MTK_HOST quirk functions in add_endpoint() and
drop_endpoint() to handle its own sw bandwidth management.
It stores bandwidth data into an internal table every time
add_endpoint() is called, and drops those in drop_endpoint().
But when bandwidth allocation fails at one endpoint, all earlier
allocation from the same interface could still remain at the table.
This patch moves bandwidth management codes to check_bandwidth() and
reset_bandwidth() path. To do so, this patch also adds those functions
to xhci_driver_overrides and lets mtk-xhci to release all failed
endpoints in reset_bandwidth() path.
Fixes: 08e469de87 ("usb: xhci-mtk: supports bandwidth scheduling with multi-TT")
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Link: https://lore.kernel.org/r/20210113180444.v6.1.Id0d31b5f3ddf5e734d2ab11161ac5821921b1e1e@changeid
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the fixes in here and this resolves a merge issue with
drivers/usb/gadget/udc/bdc/Kconfig.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Occasionally, we are seeing some SuperSpeed devices resumes right after
being directed to U3. This commits add 500us delay to ensure LFPS
detector is disabled before sending ACK to firmware.
[ 16.099363] tegra-xusb 70090000.usb: entering ELPG
[ 16.104343] tegra-xusb 70090000.usb: 2-1 isn't suspended: 0x0c001203
[ 16.114576] tegra-xusb 70090000.usb: not all ports suspended: -16
[ 16.120789] tegra-xusb 70090000.usb: entering ELPG failed
The register write passes through a few flop stages of 32KHz clock domain.
NVIDIA ASIC designer reviewed RTL and suggests 500us delay.
Cc: stable@vger.kernel.org
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210115161907.2875631-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Once the command ring doorbell is rung the xHC controller will parse all
command TRBs on the command ring that have the cycle bit set properly.
If the driver just started writing the next command TRB to the ring when
hardware finished the previous TRB, then HW might fetch an incomplete TRB
as long as its cycle bit set correctly.
A command TRB is 16 bytes (128 bits) long.
Driver writes the command TRB in four 32 bit chunks, with the chunk
containing the cycle bit last. This does however not guarantee that
chunks actually get written in that order.
This was detected in stress testing when canceling URBs with several
connected USB devices.
Two consecutive "Set TR Dequeue pointer" commands got queued right
after each other, and the second one was only partially written when
the controller parsed it, causing the dequeue pointer to be set
to bogus values. This was seen as error messages:
"Mismatch between completed Set TR Deq Ptr command & xHCI internal state"
Solution is to add a write memory barrier before writing the cycle bit.
Cc: <stable@vger.kernel.org>
Tested-by: Ross Zwisler <zwisler@google.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210115161907.2875631-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ChipIdea driver now provides USB2 host mode support for NVIDIA Tegra
SoCs. The ehci-tegra driver is obsolete now, remove it and redirect the
older Kconfig entry to the CI driver.
Tested-by: Matt Merhar <mattmerhar@protonmail.com>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Ion Agorria <ion@agorria.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20201218120246.7759-9-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The system that use Synopsys USB host controllers goes to suspend
when using USB audio player. This causes the USB host controller
continuous send interrupt signal to system, When the number of
interrupts exceeds 100000, the system will forcibly close the
interrupts and output a calltrace error.
When the system goes to suspend, the last interrupt is reported to
the driver. At this time, the system has set the state to suspend.
This causes the last interrupt to not be processed by the system and
not clear the interrupt flag. This uncleared interrupt flag constantly
triggers new interrupt event. This causing the driver to receive more
than 100,000 interrupts, which causes the system to forcibly close the
interrupt report and report the calltrace error.
so, when the driver goes to sleep and changes the system state to
suspend, the interrupt flag needs to be cleared.
Signed-off-by: Longfang Liu <liulongfang@huawei.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/1610416647-45774-1-git-send-email-liulongfang@huawei.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to EHCI spec, EHCI HC clears USBSTS.HCHalted whenever
USBCMD.RS=1.
However, it is a good practice to wait some time after setting USBCMD.RS
(approximately 100ms) until USBSTS.HCHalted become zero.
Without this waiting, VirtualBox's EHCI virtual HC accidentally hangs
(see BugLink).
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=211095
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Eugene Korenevsky <ekorenevsky@astralinux.ru>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210110173609.GA17313@himera.home
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 0472bf06c6 ("xhci: Prevent U1/U2 link pm states if exit
latency is too long") was constraining the xhci code not to allow U1/U2
sleep states if the latency to wake up from the U-states reached the
service interval of an periodic endpoint. This fix was not taking into
account that in case the quirk XHCI_INTEL_HOST is set, the wakeup time
will be calculated and configured differently.
It checks for u1_params.mel/u2_params.mel as a limit. But the code could
decide to write another MEL into the hardware. This leads to broken
cases where not enough bandwidth is available for other devices:
usb 1-2: can't set config #1, error -28
This patch is fixing that case by checking for timeout_ns after the
wakeup time was calculated depending on the quirks.
Fixes: 0472bf06c6 ("xhci: Prevent U1/U2 link pm states if exit latency is too long")
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201215193147.11738-1-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Switch to the generic C VDSO, as well as some cleanups of our VDSO
setup/handling code.
- Support for KUAP (Kernel User Access Prevention) on systems using the hashed
page table MMU, using memory protection keys.
- Better handling of PowerVM SMT8 systems where all threads of a core do not
share an L2, allowing the scheduler to make better scheduling decisions.
- Further improvements to our machine check handling.
- Show registers when unwinding interrupt frames during stack traces.
- Improvements to our pseries (PowerVM) partition migration code.
- Several series from Christophe refactoring and cleaning up various parts of
the 32-bit code.
- Other smaller features, fixes & cleanups.
Thanks to:
Alan Modra, Alexey Kardashevskiy, Andrew Donnellan, Aneesh Kumar K.V, Ard
Biesheuvel, Athira Rajeev, Balamuruhan S, Bill Wendling, Cédric Le Goater,
Christophe Leroy, Christophe Lombard, Colin Ian King, Daniel Axtens, David
Hildenbrand, Frederic Barrat, Ganesh Goudar, Gautham R. Shenoy, Geert
Uytterhoeven, Giuseppe Sacco, Greg Kurz, Harish, Jan Kratochvil, Jordan
Niethe, Kaixu Xia, Laurent Dufour, Leonardo Bras, Madhavan Srinivasan, Mahesh
Salgaonkar, Mathieu Desnoyers, Nathan Lynch, Nicholas Piggin, Oleg Nesterov,
Oliver O'Halloran, Oscar Salvador, Po-Hsu Lin, Qian Cai, Qinglang Miao, Randy
Dunlap, Ravi Bangoria, Sachin Sant, Sandipan Das, Sebastian Andrzej Siewior ,
Segher Boessenkool, Srikar Dronamraju, Tyrel Datwyler, Uwe Kleine-König,
Vincent Stehlé, Youling Tang, Zhang Xiaoxu.
-----BEGIN PGP SIGNATURE-----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=Ga3K
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- Switch to the generic C VDSO, as well as some cleanups of our VDSO
setup/handling code.
- Support for KUAP (Kernel User Access Prevention) on systems using the
hashed page table MMU, using memory protection keys.
- Better handling of PowerVM SMT8 systems where all threads of a core
do not share an L2, allowing the scheduler to make better scheduling
decisions.
- Further improvements to our machine check handling.
- Show registers when unwinding interrupt frames during stack traces.
- Improvements to our pseries (PowerVM) partition migration code.
- Several series from Christophe refactoring and cleaning up various
parts of the 32-bit code.
- Other smaller features, fixes & cleanups.
Thanks to: Alan Modra, Alexey Kardashevskiy, Andrew Donnellan, Aneesh
Kumar K.V, Ard Biesheuvel, Athira Rajeev, Balamuruhan S, Bill Wendling,
Cédric Le Goater, Christophe Leroy, Christophe Lombard, Colin Ian King,
Daniel Axtens, David Hildenbrand, Frederic Barrat, Ganesh Goudar,
Gautham R. Shenoy, Geert Uytterhoeven, Giuseppe Sacco, Greg Kurz,
Harish, Jan Kratochvil, Jordan Niethe, Kaixu Xia, Laurent Dufour,
Leonardo Bras, Madhavan Srinivasan, Mahesh Salgaonkar, Mathieu
Desnoyers, Nathan Lynch, Nicholas Piggin, Oleg Nesterov, Oliver
O'Halloran, Oscar Salvador, Po-Hsu Lin, Qian Cai, Qinglang Miao, Randy
Dunlap, Ravi Bangoria, Sachin Sant, Sandipan Das, Sebastian Andrzej
Siewior , Segher Boessenkool, Srikar Dronamraju, Tyrel Datwyler, Uwe
Kleine-König, Vincent Stehlé, Youling Tang, and Zhang Xiaoxu.
* tag 'powerpc-5.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (304 commits)
powerpc/32s: Fix cleanup_cpu_mmu_context() compile bug
powerpc: Add config fragment for disabling -Werror
powerpc/configs: Add ppc64le_allnoconfig target
powerpc/powernv: Rate limit opal-elog read failure message
powerpc/pseries/memhotplug: Quieten some DLPAR operations
powerpc/ps3: use dma_mapping_error()
powerpc: force inlining of csum_partial() to avoid multiple csum_partial() with GCC10
powerpc/perf: Fix Threshold Event Counter Multiplier width for P10
powerpc/mm: Fix hugetlb_free_pmd_range() and hugetlb_free_pud_range()
KVM: PPC: Book3S HV: Fix mask size for emulated msgsndp
KVM: PPC: fix comparison to bool warning
KVM: PPC: Book3S: Assign boolean values to a bool variable
powerpc: Inline setup_kup()
powerpc/64s: Mark the kuap/kuep functions non __init
KVM: PPC: Book3S HV: XIVE: Add a comment regarding VP numbering
powerpc/xive: Improve error reporting of OPAL calls
powerpc/xive: Simplify xive_do_source_eoi()
powerpc/xive: Remove P9 DD1 flag XIVE_IRQ_FLAG_EOI_FW
powerpc/xive: Remove P9 DD1 flag XIVE_IRQ_FLAG_MASK_FW
powerpc/xive: Remove P9 DD1 flag XIVE_IRQ_FLAG_SHIFT_BUG
...
Here is the big driver core updates for 5.11-rc1
This time there was a lot of different work happening here for some
reason:
- redo of the fwnode link logic, speeding it up greatly
- auxiliary bus added (this was a tag that will be pulled in
from other trees/maintainers this merge window as well, as
driver subsystems started to rely on it)
- platform driver core cleanups on the way to fixing some
long-time api updates in future releases
- minor fixes and tweaks.
All have been in linux-next with no (finally) reported issues. Testing
there did helped in shaking issues out a lot :)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCX9iEUQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynBJwCgjBAtVWXquZz4m/pyjn0HoTC7tdYAnAlQIj9s
vRbPjOgH9R+YRJzFs1Kx
=X6UP
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the big driver core updates for 5.11-rc1
This time there was a lot of different work happening here for some
reason:
- redo of the fwnode link logic, speeding it up greatly
- auxiliary bus added (this was a tag that will be pulled in from
other trees/maintainers this merge window as well, as driver
subsystems started to rely on it)
- platform driver core cleanups on the way to fixing some long-time
api updates in future releases
- minor fixes and tweaks.
All have been in linux-next with no (finally) reported issues. Testing
there did helped in shaking issues out a lot :)"
* tag 'driver-core-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (39 commits)
driver core: platform: don't oops in platform_shutdown() on unbound devices
ACPI: Use fwnode_init() to set up fwnode
misc: pvpanic: Replace OF headers by mod_devicetable.h
misc: pvpanic: Combine ACPI and platform drivers
usb: host: sl811: Switch to use platform_get_mem_or_io()
vfio: platform: Switch to use platform_get_mem_or_io()
driver core: platform: Introduce platform_get_mem_or_io()
dyndbg: fix use before null check
soc: fix comment for freeing soc_dev_attr
driver core: platform: use bus_type functions
driver core: platform: change logic implementing platform_driver_probe
driver core: platform: reorder functions
driver core: make driver_probe_device() static
driver core: Fix a couple of typos
driver core: Reorder devices on successful probe
driver core: Delete pointless parameter in fwnode_operations.add_links
driver core: Refactor fw_devlink feature
efi: Update implementation of add_links() to create fwnode links
of: property: Update implementation of add_links() to create fwnode links
driver core: Use device's fwnode to check if it is waiting for suppliers
...
Switch to use new platform_get_mem_or_io() instead of home grown analogue.
Note, the code has been moved upper in the function to allow farther cleanups,
such as resource sanity check.
Cc: linux-usb@vger.kernel.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20201209203642.27648-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_create_hcd will alloc memory for hcd, and we should
call usb_put_hcd to free it when adding fails to prevent
memory leak.
Fixes: b92a78e582 ("usb host: Oxford OXU210HP HCD driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201123145809.1456541-1-zhangqilong3@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pm_runtime_enable will decrement the power disable depth. Imbalance
depth will resulted in enabling runtime PM of device fails later. Thus
a pairing decrement must be needed on the error handling path to keep it
balanced.
Fixes: 6c984b066d ("ARM: OMAP: USBHOST: Replace usbhs core driver APIs by Runtime pm APIs")
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201123145719.1455849-1-zhangqilong3@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a USB2 device wakeup is not enabled/supported the link state may
still be in U0 in xhci_bus_suspend(), where it's then manually put
to suspended U3 state.
Just as with selective suspend the device needs time to enter U3
suspend before continuing with further suspend operations
(e.g. system suspend), otherwise we may enter system suspend with link
state in U0.
[commit message rewording -Mathias]
Cc: <stable@vger.kernel.org>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20201208092912.1773650-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel Maple Ridge is successor of Titan Ridge Thunderbolt controller. As
Titan Ridge this one also includes xHCI host controller. In order to
safe energy we should put it to low power state by default when idle.
For this reason allow host runtime PM for Maple Ridge.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20201208092912.1773650-5-mathias.nyman@linux.intel.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xHCI controller on Alpine Ridge LP keeps the whole Thunderbolt
controller awake if the host controller is not allowed to sleep.
This is the case even if no USB devices are connected to the host.
Add the Intel Alpine Ridge LP product-id to the list of product-ids
for which we allow runtime PM by default.
Fixes: 2815ef7fe4 ("xhci-pci: allow host runtime PM as default for Intel Alpine and Titan Ridge")
Cc: <stable@vger.kernel.org>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20201208092912.1773650-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Synopsys xHC has an internal TRB cache of size TRB_CACHE_SIZE for
each endpoint. The default value for TRB_CACHE_SIZE is 16 for SS and 8
for HS. The controller loads and updates the TRB cache from the transfer
ring in system memory whenever the driver issues a start transfer or
update transfer command.
For chained TRBs, the Synopsys xHC requires that the total amount of
bytes for all TRBs loaded in the TRB cache be greater than or equal to 1
MPS. Or the chain ends within the TRB cache (with a last TRB).
If this requirement is not met, the controller will not be able to send
or receive a packet and it will hang causing a driver timeout and error.
This can be a problem if a class driver queues SG requests with many
small-buffer entries. The XHCI driver will create a chained TRB for each
entry which may trigger this issue.
This patch adds logic to the XHCI driver to detect and prevent this from
happening.
For every (TRB_CACHE_SIZE - 2), we check the total buffer size of
the SG list and if the last window of (TRB_CACHE_SIZE - 2) SG list length
and we don't make up at least 1 MPS, we create a temporary buffer to
consolidate full SG list into the buffer.
We check at (TRB_CACHE_SIZE - 2) window because it is possible that there
would be a link and/or event data TRB that take up to 2 of the cache
entries.
We discovered this issue with devices on other platforms but have not
yet come across any device that triggers this on Linux. But it could be
a real problem now or in the future. All it takes is N number of small
chained TRBs. And other instances of the Synopsys IP may have smaller
values for the TRB_CACHE_SIZE which would exacerbate the problem.
Signed-off-by: Tejas Joglekar <joglekar@synopsys.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20201208092912.1773650-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit uses the private data passed by parent device
to set the quirk for Synopsys xHC. This patch fixes the
SNPS xHC hang issue when the data is scattered across
small buffers which does not make atleast MPS size for
given TRB cache size of SNPS xHC.
Signed-off-by: Tejas Joglekar <joglekar@synopsys.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20201208092912.1773650-2-mathias.nyman@linux.intel.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There were a bunch of issues with the patch converting the
OMAP1 OSK board to use descriptors for controlling the USB
host:
- The chip label was incorrect
- The GPIO offset was off-by-one
- The code should use sleeping accessors
This patch tries to fix all issues at the same time.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Fixes: 15d157e874 ("usb: ohci-omap: Convert to use GPIO descriptors")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20201130083033.29435-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver core ignores the return value of struct device_driver::remove
because there is only little that can be done. For the shutdown callback
it's ps3_system_bus_shutdown() which ignores the return value.
To simplify the quest to make struct device_driver::remove return void,
let struct ps3_system_bus_driver::remove return void, too. All users
already unconditionally return 0, this commit makes it obvious that
returning an error code is a bad idea and ensures future users behave
accordingly.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201126165950.2554997-2-u.kleine-koenig@pengutronix.de
retval may be reassigned to 0 after max3421_of_vbus_en_pin(),
if allocate memory failed after this, max3421_probe() cann't
return ENOMEM, fix this by moving assign retval afther max3421_probe().
Fixes: 721fdc83b3 ("usb: max3421: Add devicetree support")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20201117061500.3454223-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ehci-mxc driver was only used by i.MX non-DT platforms.
Since 5.10-rc1, i.MX has been converted to a DT-only platform and all
board files are gone.
Remove the ehci-mxc driver as there are no more users at all.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20201113171231.2205-1-festevam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 4b563a0666 ("ARM: imx: Remove imx21 support") the imx21
SoC is no longer supported.
Get rid of its USB driver too, which is now unused.
Acked-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20201109210813.21382-1-festevam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "fallthrough" pseudo-keyword was added as a portable way to denote
intentional fallthrough. Clang will still warn on cases where there is a
fallthrough to an immediate break. Add explicit breaks for those cases.
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/r/20201111014716.260633-1-ndesaulniers@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Moritz Fischer