A small selection of macros which can only accept dev_priv from
now on and a resulting trickle of fixups.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
There are certain types of interrupts which Host can receive from GuC.
GuC ukernel sends an interrupt to Host for certain events, like for
example retrieve/consume the logs generated by ukernel.
This patch adds support to receive interrupts from GuC but currently
enables & partially handles only the interrupt sent by GuC ukernel.
Future patches will add support for handling other interrupt types.
v2:
- Use common low level routines for PM IER/IIR programming (Chris)
- Rename interrupt functions to gen9_xxx from gen8_xxx (Chris)
- Replace disabling of wake ref asserts with rpm get/put (Chris)
v3:
- Update comments for more clarity. (Tvrtko)
- Remove the masking of GuC interrupt, which was kept masked till the
start of bottom half, its not really needed as there is only a
single instance of work item & wq is ordered. (Tvrtko)
v4:
- Rebase.
- Rename guc_events to pm_guc_events so as to be indicative of the
register/control block it is associated with. (Chris)
- Add handling for back to back log buffer flush interrupts.
v5:
- Move the read & clearing of register, containing Guc2Host message
bits, outside the irq spinlock. (Tvrtko)
v6:
- Move the log buffer flush interrupt related stuff to the following
patch so as to do only generic bits in this patch. (Tvrtko)
- Rebase.
v7:
- Remove the interrupts_enabled check from gen9_guc_irq_handler, want to
process that last interrupt also before disabling the interrupt, sync
against the work queued by irq handler will be done by caller disabling
the interrupt.
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Akash Goel <akash.goel@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
So far there were 2 fields related to GuC logs in 'intel_guc' structure.
For the support of capturing GuC logs & storing them in a local buffer,
multiple new fields would have to be added. This warrants a separate
structure to contain the fields related to GuC logging state.
Added a new structure 'intel_guc_log' and instance of it inside
'intel_guc' structure.
v2: Rebase.
Signed-off-by: Akash Goel <akash.goel@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
GuC Log buffer allocation was tied up with verbosity level module param
i915.guc_log_level. User would be given a provision to enable firmware
logging at runtime, through a host2guc action, and not necessarily during
Driver load time. But the address of log buffer can be passed only in
init params, at firmware load time, so GuC has to be reset and firmware
needs to be reloaded to pass the log buffer address at runtime.
To avoid reset of GuC & reload of firmware, allocation of log buffer will
be done always but logging would be enabled initially on GuC side based on
the value of module parameter guc_log_level.
v2: Update commit message to describe the constraint with allocation of
log buffer at runtime. (Tvrtko)
v3: Rebase.
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Akash Goel <akash.goel@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
i915.enable_guc_loading/submission=2 forces the usage of GuC.
For platforms that do not have a GuC, asking the kernel to use a GuC
should not result in an error state. Do extra checks to see if the
platform even has a GuC or not, regardless of the kernel parameter.
v2: Based on Rodrigo's patch and Paulo's suggestion(Paulo, Rodrigo)
v3: Correct the Indentation(Jani, Paulo)
v4: Added the blank line(Jani, Paulo)
v5 (from Paulo): Remove the extra blank line.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=97573
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Zanoni Paulo <paulo.r.zanoni@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1476488825-5673-1-git-send-email-anusha.srivatsa@intel.com
Saves 1392 bytes of .rodata strings.
Also change a few function/macro prototypes in i915_gem_gtt.c
from dev to dev_priv where it made more sense to do so.
v2: Add parantheses around dev_priv. (Ville Syrjala)
v3: Mention function prototype changes. (David Weinehall)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: David Weinehall <david.weinehall@linux.intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Jani Nikula <jani.nikula@linux.intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
Saves 1016 bytes of .rodata strings and couple hundred of .text.
v2: Add parantheses around dev_priv. (Ville Syrjala)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Jani Nikula <jani.nikula@linux.intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
With the possibility of addition of many more number of rings in future,
the drm_i915_private structure could bloat as an array, of type
intel_engine_cs, is embedded inside it.
struct intel_engine_cs engine[I915_NUM_ENGINES];
Though this is still fine as generally there is only a single instance of
drm_i915_private structure used, but not all of the possible rings would be
enabled or active on most of the platforms. Some memory can be saved by
allocating intel_engine_cs structure only for the enabled/active engines.
Currently the engine/ring ID is kept static and dev_priv->engine[] is simply
indexed using the enums defined in intel_engine_id.
To save memory and continue using the static engine/ring IDs, 'engine' is
defined as an array of pointers.
struct intel_engine_cs *engine[I915_NUM_ENGINES];
dev_priv->engine[engine_ID] will be NULL for disabled engine instances.
There is a text size reduction of 928 bytes, from 1028200 to 1027272, for
i915.o file (but for i915.ko file text size remain same as 1193131 bytes).
v2:
- Remove the engine iterator field added in drm_i915_private structure,
instead pass a local iterator variable to the for_each_engine**
macros. (Chris)
- Do away with intel_engine_initialized() and instead directly use the
NULL pointer check on engine pointer. (Chris)
v3:
- Remove for_each_engine_id() macro, as the updated macro for_each_engine()
can be used in place of it. (Chris)
- Protect the access to Render engine Fault register with a NULL check, as
engine specific init is done later in Driver load sequence.
v4:
- Use !!dev_priv->engine[VCS] style for the engine check in getparam. (Chris)
- Kill the superfluous init_engine_lists().
v5:
- Cleanup the intel_engines_init() & intel_engines_setup(), with respect to
allocation of intel_engine_cs structure. (Chris)
v6:
- Rebase.
v7:
- Optimize the for_each_engine_masked() macro. (Chris)
- Change the type of 'iter' local variable to enum intel_engine_id. (Chris)
- Rebase.
v8: Rebase.
v9: Rebase.
v10:
- For index calculation use engine ID instead of pointer based arithmetic in
intel_engine_sync_index() as engine pointers are not contiguous now (Chris)
- For appropriateness, rename local enum variable 'iter' to 'id'. (Joonas)
- Use for_each_engine macro for cleanup in intel_engines_init() and remove
check for NULL engine pointer in cleanup() routines. (Joonas)
v11: Rebase.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Akash Goel <akash.goel@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1476378888-7372-1-git-send-email-akash.goel@intel.com
No functional changes; just renaming a bit, tweaking a datatype,
prettifying layout, and adding comments, in particular in the
GuC setup code that touches this data.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1473711577-11454-2-git-send-email-david.s.gordon@intel.com
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Some downgraded from DRM_ERROR() to DRM_WARN() or DRM_NOTE(),
a few upgraded from DRM_INFO() to DRM_NOTE() or DRM_WARN(),
and one eliminated completely.
v2: different permutation of levels :)
v3: convert a couple of "this shouldn't happen" messages to WARN()
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
In an effort to simplify things for a future push of dev_priv instead
of dev wherever possible, always take pdev via dev_priv where
feasible, eliminating the direct access from dev. Right now this
only eliminates a few cases of dev, but it also obviates that we pass
dev into a lot of functions where dev_priv would be the more obvious
choice.
v2: Fixed one more place missing in the previous patch set
Signed-off-by: David Weinehall <david.weinehall@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20160822103245.24069-5-david.weinehall@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This little helper only exists to safely discard the upper unused 32bits
of the general 64-bit VMA address - as we know that all Global GTT
currently are less than 4GiB in size and so that the upper bits must be
zero. In many places, we use a u32 for the global GTT offset and we want
to document where we are discarding the full VMA offset.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1471254551-25805-28-git-send-email-chris@chris-wilson.co.uk
Treat the VMA as the primary struct responsible for tracking bindings
into the GPU's VM. That is we want to treat the VMA returned after we
pin an object into the VM as the cookie we hold and eventually release
when unpinning. Doing so eliminates the ambiguity in pinning the object
and then searching for the relevant pin later.
v2: Joonas' stylistic nitpicks, a fun rebase.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1471254551-25805-27-git-send-email-chris@chris-wilson.co.uk
Since the guc allocates and pins and object into the GGTT for its usage,
it is more natural to use that pinned VMA as our resource cookie.
v2: Embrace naming tautology
v3: Rewrite comments for guc_allocate_vma()
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1471254551-25805-12-git-send-email-chris@chris-wilson.co.uk
Currently to change the firmware one has to update the exported
module firmware string and the major-minor versions used for
verification after load. Consolidate that to a single place
defining correct major and minor versions per platform.
v2: Rebased for KBL.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Dave Gordon <david.s.gordon@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Peter Antoine <peter.antoine@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470842206-35685-1-git-send-email-tvrtko.ursulin@linux.intel.com
Since i915_gem_obj_ggtt_pin() is an idiom breaking curry function for
i915_gem_object_ggtt_pin(), spare us the confusion and remove it.
Removing it now simplifies later patches to change the i915_vma_pin()
(and friends) interface.
v2: Add a redundant GEM_BUG_ON(!view) to
i915_gem_obj_lookup_or_create_ggtt_vma()
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470324762-2545-18-git-send-email-chris@chris-wilson.co.uk
WaC6DisallowByGfxPause is currently applied unconditionally
but is not required in all revisions.
v2: extend application of workaround to agree with w/a
database, which differs from the HSD.
References: HSD#2133391
Signed-off-by: Tim Gore <tim.gore@intel.com>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1469008825-19442-1-git-send-email-tim.gore@intel.com
Since drm_i915_private is now a subclass of drm_device we do not need to
chase the drm_i915_private->dev backpointer and can instead simply
access drm_i915_private->drm directly.
text data bss dec hex filename
1068757 4565 416 1073738 10624a drivers/gpu/drm/i915/i915.ko
1066949 4565 416 1071930 105b3a drivers/gpu/drm/i915/i915.ko
Created by the coccinelle script:
@@
struct drm_i915_private *d;
identifier i;
@@
(
- d->dev->i
+ d->drm.i
|
- d->dev
+ &d->drm
)
and for good measure the dev_priv->dev backpointer was removed entirely.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1467711623-2905-4-git-send-email-chris@chris-wilson.co.uk
Since we now subclass struct drm_device, we can save pointer dances by
noting the equivalence of struct drm_device and struct drm_i915_private,
i.e. by using to_i915().
text data bss dec hex filename
1073824 4562 416 1078802 107612 drivers/gpu/drm/i915/i915.ko
1068976 4562 416 1073954 106322 drivers/gpu/drm/i915/i915.ko
Created by the coccinelle script:
@@
expression E;
identifier p;
@@
- struct drm_i915_private *p = E->dev_private;
+ struct drm_i915_private *p = to_i915(E);
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1467628477-25379-1-git-send-email-chris@chris-wilson.co.uk
This patch added the loading of the GuC for Kabylake.
It loads a 9.14 firmware.
v2: Fix commit message
v3: Fix major/minor var names to match -nightly. (Rodrigo)
Cc: Christophe Prigent <christophe.prigent@intel.com>
Signed-off-by: Peter Antoine <peter.antoine@intel.com>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com> (v3)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1467304672-2106-1-git-send-email-rodrigo.vivi@intel.com
If a context waiting for VBlank were switched out, switching
in the next context and generating a CSB event in the process,
then the GuC would have to put the context back in the queue,
and then observe the subsequent VBlank interrupt so that it
could resubmit the suspended context.
However, we always set the CTX_CTRL_INHIBIT_SYN_CTX_SWITCH bit
in the RING_CONTEXT_CONTROL register, so this case cannot occur.
Furthermore we don't use the GuC's internal scheduler or allow
it to auto-resubmit workloads. Consequently, the GuC doesn't
need to see VBlanks, and by sending them to it we may be waking
it up unnecessarily, which might reduce RC6 residency and
increase power consumption.
So this patch removes the setting of the GFC_FORWARD_VBLANK
field from the code that diverts interrupts towards the GuC.
(The code to direct interrupts to the host, OTOH, continues to
explicitly set the field to "never send VBlanks to the GuC".)
v3:
Remove the line of code completely (original set the field
to ALWAYS forward, v1 changed it to CONDITIONAL forwarding,
v2 explicitly set it to NEVER, v3 just doesn't touch it at
all, as we know it's already set to NEVER).
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> (previous version)
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466780277-23435-1-git-send-email-david.s.gordon@intel.com
There are four non-static functions in i915_guc_submission.c that take a
'dev' parameter. All are called only from GuC loader code, and can be
easily converted to accept 'dev_priv' instead.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465579766-31595-1-git-send-email-david.s.gordon@intel.com
If the user doesn't override the default values of the GuC-related
kernel parameters, then on a non-GuC-based platform we shouldn't
mention that we haven't loaded the GuC firmware.
The various messages have been reordered into a least->most severe
cascade (none/INFO/INFO/ERROR) for ease of comprehension.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465575685-34169-1-git-send-email-david.s.gordon@intel.com
When resetting and reloading the GuC, the GuC submission management code
also needs to destroy and recreate the GuC client(s). Currently this is
done by a separate call from the GuC loader, but really, it's just an
internal detail of the submission code. So here we remove the call from
the loader (which is too late, really, because the GuC has already been
reloaded at this point) and put it into guc_submission_init() instead.
This means that any preexisting client is destroyed *before* the GuC
(re)load and then recreated after, iff the firmware was successfully
loaded. If the GuC reload fails, we don't recreate the client, so
fallback to execlists mode (if active) won't leak the client object
(previously, the now-unusable client would have been left allocated,
and leaked if the driver were unloaded).
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
The last stage of the GuC loader also sanitises the GuC submission
settings, so should be called unconditionally (even on platforms
without a GuC) to ensure consistent settings; in particular, this
prevents any attempt to use GuC submission on GuCless platforms!
Also fix error path handling and clarify DRM_INFO fallback message.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
On Loading, GuC sets PM interrupts routing (bit 31) and clears ARAT
expired interrupt (bit 9). Host turbo also updates this register
in RPS flows. This patch ensures bit 31 and bit 9 setup by GuC persists.
ARAT timer interrupt is needed in GuC for various features. It also
facilitates halting GuC and hence achieving RC6. PM interrupt routing
will not impact RPS interrupt reception by host as GuC will redirect
them.
This patch fixes igt test pm_rc6_residency that was failing with guc
load/submission enabled. Tested with SKL GuC v6.1 and BXT GuC v5.1 and v8.7.
v2: i915_irq/i915_pm decoupling from intel_guc. (ChrisW)
v3: restructuring the mask update and rebase w.r.t Ville's patch. (ChrisW)
v4: Updating the pm_intr_keep during direct_interrupts_to_guc. (Sagar)
Cc: Chris Harris <chris.harris@intel.com>
Cc: Zhe Wang <zhe1.wang@intel.com>
Cc: Deepak S <deepak.s@intel.com>
Cc: Satyanantha, Rama Gopal M <rama.gopal.m.satyanantha@intel.com>
Cc: Akash Goel <akash.goel@intel.com>
Testcase: igt/pm_rc6_residency
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Tested-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464683307-19475-1-git-send-email-sagar.a.kamble@intel.com
Split the function of "enable_guc_submission" into two separate
options. The new one ("enable_guc_loading") controls only the
*fetching and loading* of the GuC firmware image. The existing
one is redefined to control only the *use* of the GuC for batch
submission once the firmware is loaded.
In addition, the degree of control has been refined from a simple
bool to an integer key, allowing several options:
-1 (default) whatever the platform default is
0 DISABLE don't load/use the GuC
1 BEST EFFORT try to load/use the GuC, fallback if not available
2 REQUIRE must load/use the GuC, else leave the GPU wedged
The new platform default (as coded here) will be to attempt to
load the GuC iff the device has a GuC that requires firmware,
but not yet to use it for submission. A later patch will change
to enable it if appropriate.
v4:
Changed some error-message levels, mostly ERROR->INFO, per
review comments by Tvrtko Ursulin.
v5:
Dropped one more error message, disabled GuC submission on
hypothetical firmware-free devices [Tvrtko Ursulin].
v6:
Logging tidy by Tvrtko Ursulin:
* Do not log falling back to execlists when wedging the GPU.
* Do not log fw load errors when load was disabled by user.
* Pass down some error code from fw load for log message to
make more sense.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> (v5)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Tested-by: Fiedorowicz, Lukasz <lukasz.fiedorowicz@intel.com>
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> (v5)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Nick Hoath <nicholas.hoath@intel.com> (v6)
The GuC initialisation code could do other things apart from loading
firmware, so here we rename the three primary entry points to remove any
specific reference to "ucode" (no functional changes, just renaming).
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
This patch resizes the GuC WOPCM (specifically on BXT)
so that the GuC and RC6 memory spaces do not overlap.
v2:
Made calculation of WOPCM size into a separate function,
so that it's consistent between the firmware size-check
and the register-programming operations [Dave Gordon].
Issue: https://jira01.devtools.intel.com/browse/VIZ-6638
Signed-off-by: Peter Antoine <peter.antoine@intel.com>
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Nick Hoath <nicholas.hoath@intel.com>
Tested-by: Nick Hoath <nicholas.hoath@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463494365-26330-1-git-send-email-david.s.gordon@intel.com
Load guc firmware from file with major_minor number
in filename instead of using symolic link with only
major number.
This change is so that new firmwares can only be used
with a kernel change. This in case there is a regression
with a new firmware, it won't be used by default without
some testing.
Issue: VIZ-7713
Signed-off-by: Tom O'Rourke <Tom.O'Rourke@intel.com>
Signed-off-by: Nick Hoath <nicholas.hoath@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: peter.antoine@intel.com
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
After a suspend-resume cycle, the resumed kernel has no idea what the
booted kernel may have done to the GuC before replacing itself with the
resumed image. In particular, it may have already loaded the GuC with
firmware, which will then cause this kernel's attempt to (re)load the
firmware to fail (GuC program memory is write-once!). The symptoms
(GuC firmware reload fails after hibernation) are further described
in the Bugzilla reference below.
So let's *always* reset the GuC just before (re)loading the firmware;
the hardware should then be in a well-known state, and we may even
avoid some of the issues arising from unpredictable timing.
Also added some more fields & values to the definition of the GUC_STATUS
register, which is the key diagnostic indicator if the GuC load fails.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Cc: Alex Dai <yu.dai@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94390
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Due to timing issues in the HW, some of the status bits required for GuC
authentication occasionally don't get set; when that happens, the GuC
cannot be initialized and we will be left with a wedged GPU. The W/A
suggested is to perform a soft reset of the GuC and attempt to reload
the F/W again for few times before giving up.
As the failure is dependent on timing, tests performed by triggering
manual full gpu reset (i915_wedged) showed that we could sometimes hit
this after several thousand iterations, but sometimes tests ran even
longer without any issues. Reset and reload mechanism proved helpful
when we indeed hit f/w load failure, so it is better to include this
to improve driver stability.
This change implements the following WAs,
WaEnableuKernelHeaderValidFix:skl,bxt
WaEnableGuCBootHashCheckNotSet:skl,bxt
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Alex Dai <yu.dai@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Having provided for_each_engine_id() for cases where the third (id)
argument is useful, we can now replace all the remaining instances with
a simpler version that takes only two parameters. In many cases, this
also allows the elimination of the local variable used in the iterator
(usually 'i').
v2:
s/dev_priv/(dev_priv__)/ in body of for_each_engine_masked() [Chris Wilson]
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458757194-17783-2-git-send-email-david.s.gordon@intel.com
This version of GuC firmware fixes the engine reset issue where golden
context LRC address is treated as page index by mistake. It also fixes
the problem that scheduler stops submiting to one engine when the other
engine work queue is full.
Signed-off-by: Alex Dai <yu.dai@intel.com>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Some trivial ones, first pass done with Coccinelle:
@@
@@
(
- I915_NUM_RINGS
+ I915_NUM_ENGINES
|
- intel_ring_flag
+ intel_engine_flag
|
- for_each_ring
+ for_each_engine
|
- i915_gem_request_get_ring
+ i915_gem_request_get_engine
|
- intel_ring_idle
+ intel_engine_idle
|
- i915_gem_reset_ring_status
+ i915_gem_reset_engine_status
|
- i915_gem_reset_ring_cleanup
+ i915_gem_reset_engine_cleanup
|
- init_ring_lists
+ init_engine_lists
)
But that didn't fully work so I cleaned it up with:
for f in *.[hc]; do sed -i -e s/I915_NUM_RINGS/I915_NUM_ENGINES/ $f; done
for f in *.[hc]; do sed -i -e s/i915_gem_request_get_ring/i915_gem_request_get_engine/ $f; done
for f in *.[hc]; do sed -i -e s/intel_ring_flag/intel_engine_flag/ $f; done
for f in *.[hc]; do sed -i -e s/intel_ring_idle/intel_engine_idle/ $f; done
for f in *.[hc]; do sed -i -e s/init_ring_lists/init_engine_lists/ $f; done
for f in *.[hc]; do sed -i -e s/i915_gem_reset_ring_cleanup/i915_gem_reset_engine_cleanup/ $f; done
for f in *.[hc]; do sed -i -e s/i915_gem_reset_ring_status/i915_gem_reset_engine_status/ $f; done
v2: Rebase.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
It does not look like this code needs to wait atomically?
Higher in the call chain it calls the GEM API and I do
not see that the section is under any spin locks or such.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Alex Dai <yu.dai@intel.com>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
During driver unloading, the guc_client created for command submission
needs to be released to avoid memory leak.
The struct_mutex needs to be held before tearing down GuC.
v1: Move i915_guc_submission_disable out of i915_guc_submission_fini and
take struct_mutex lock before release GuC client. (Dave Gordon)
v2: Add the locking for failure case in guc_fw_fetch. (Dave Gordon)
Add i915_guc_submission_fini for failure case in intel_guc_ucode_load.
Signed-off-by: Alex Dai <yu.dai@intel.com>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1452711710-4505-1-git-send-email-yu.dai@intel.com
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWUmHZAAoJEHm+PkMAQRiGHtcH/RVRsn8re0WdRWYaTr9+Hknm
CGlRJN4LKecttgYQ/2bS1QsDbt8usDPBiiYVopqGXQxPBmjyDAqPjsa+8VzCaVc6
WA+9LDB+PcW28lD6BO+qSZCOAm7hHSZq7dtw9x658IqO+mI2mVeCybsAyunw2iWi
Kf5q90wq6tIBXuT8YH9MXGrSCQw00NclbYeYwB9CmCt9hT/koEFBdl7uFUFitB+Q
GSPTz5fXhgc5Lms85n7flZlrVKoQKmtDQe4/DvKZm+SjsATHU9ru89OxDBdS5gSG
YcEIM4zc9tMjhs3GC9t6WXf6iFOdctum8HOhUoIN/+LVfeOMRRwAhRVqtGJ//Xw=
=DCUg
-----END PGP SIGNATURE-----
Merge tag 'v4.4-rc2' into drm-intel-next-queued
Linux 4.4-rc2
Backmerge to get at
commit 1b0e3a049e
Author: Imre Deak <imre.deak@intel.com>
Date: Thu Nov 5 23:04:11 2015 +0200
drm/i915/skl: disable display side power well support for now
so that we can proplery re-eanble skl power wells in -next.
Conflicts are just adjacent lines changed, except for intel_fbdev.c
where we need to interleave the changs. Nothing nefarious.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Tvrtko Ursulin