It's possible that BIOS enables PHY0, but it programmes only the first
channel on it. Since we program the PHYs only during driver loading this
is an incorrect configuration from the driver's point of view, since we
may use both channels eventually. Detect this scenario and force
reprogramming the PHY in this case.
The actual scenario for me was that the lane optimization for the second
channel in PHY0 was not setup by BIOS and so a state verification
warning was triggered. Everything else was setup properly.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461174366-16758-4-git-send-email-imre.deak@intel.com
If we skipped PHY0 initialization because it was already enabled by
BIOS, we still have to wait for the PHY1 GRC calibration as that is
done as part of the PHY0 init.
v2:
- Use the actual PHY index in the debug message in
broxton_phy_wait_grc_done() (Ville)
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461255561-1644-1-git-send-email-imre.deak@intel.com
It's possible that BIOS enables PHY1 only to read out the GRC value from
it to be used in PHY0 and then disables PHY1. In this case we can't use
the PHY1 GRC value for state verification, so use instead the one in PHY0
always.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461174366-16758-2-git-send-email-imre.deak@intel.com
It was noticed on bug #94087 that module parameter
i915.edp_vswing=2 that should override the VBT setting
to use default voltage swing (400 mV) was not applied
for Broadwell.
This patch provides a fix for this by checking if default
i.e. higher voltage swing is requested to be used and
applies the DDI translations table for DP instead of eDP
(low vswing) table.
v2: Combine two if statements into one (Jani)
v3: Change dev_priv->edp_low_vswing to use dev_priv->vbt.edp.low_vswing
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94087
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461155942-7749-1-git-send-email-mika.kahola@intel.com
Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
The driver's VDD on/off logic assumes that whenever the VDD is on we
also hold an AUX power domain reference. Since BIOS can leave the VDD on
during booting and resuming and on DDI platforms we won't take a
corresponding power reference, the above assumption won't hold on those
platforms and an eventual delayed VDD off work will do an extraneous AUX
power domain put resulting in a refcount underflow. Fix this the same
way we did this for non-DDI DP encoders:
commit 6d93c0c417 ("drm/i915: fix VDD state tracking after system
resume")
At the same time call the DP encoder suspend handler the same way as the
non-DDI DP encoders do to flush any pending VDD off work. Leaving the
work running may cause a HW access where we don't expect this (at a point
where power domains are suspended already).
While at it remove an unnecessary function call indirection.
This fixed for me AUX refcount underflow problems on BXT during
suspend/resume.
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
CC: stable@vger.kernel.org
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460963062-13211-4-git-send-email-imre.deak@intel.com
I caught a few errors in our current PHY/CDCLK programming by sanity
checking the actual programmed state, so I thought it would be also
useful for the future. In addition to verifying the state after
programming it also verify it after exiting DC5, to make sure DMC
restored/kept intact everything related.
v2:
- Inlining __phy_reg_verify_state() doesn't make sense and also
incorrect, so don't do it (PW/CI gcc)
v3:
- Rebase on latest -nightly
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: David Weinehall <david.weinehall@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459780030-15781-1-git-send-email-imre.deak@intel.com
If BIOS has already programmed and enabled a PHY, don't reprogram it as
that may interfere with the currently active outputs. A follow-up patch
will add state verification, so we can catch any misconfiguration on
BIOS's behalf.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459515767-29228-14-git-send-email-imre.deak@intel.com
The power-down step logically belongs to the individual PHY uninit
sequence so move it there. The only functional change is that we will
power down now PHY 1 separately before PHY 0 and preserve the other bits
in the register which are defined as reserved.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459515767-29228-11-git-send-email-imre.deak@intel.com
For internal APIs passing dev_priv is preferred to reduce indirections,
so convert over a few DDI PHY, CDCLK helpers.
No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: David Weinehall <david.weinehall@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459515767-29228-10-git-send-email-imre.deak@intel.com
This register is read-only, so we have never actually set
OCL2_LDOFUSE_PWR_DIS in it as specified by the specification. Add a code
comment about this. I filed a specification update request to clarify
this there.
CC: Arthur J Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: David Weinehall <david.weinehall@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459515767-29228-4-git-send-email-imre.deak@intel.com
Bspec is confused w.r.t. the HSW/BDW FDI disable sequence. It lists
FDI RX disable both as step 13 and step 18 in the sequence. But I dug
up an old BUN mail from Art that moved the FDI RX disable to happen
before DDI_BUF_CTL disable. That BUN did not renumber the steps and just
added a note:
"Workaround: Disable PCH FDI Receiver before disabling DDI_BUF_CTL."
The BUN described the symptoms of the fixed issue as:
"PCH display underflow and a black screen on the analog CRT port that
happened after a FDI re-train"
I suppose later someone tried to renumber the steps to match, but forgot
to remove the FDI RX disable from its old position in the sequence.
They also forgot to update the note describing what should be done in
case of an FDI training failure. Currently it says:
"To retry FDI training, follow the Disable Sequence steps to Disable FDI,
but skip the steps related to clocks and PLLs (16, 19, and 20), ..."
It should really say "17, 20, and 21" with the current sequence because
those are the steps that deal with PLLs and whatnot, after step 13 became
FDI RX disable. And had the step 18 FDI RX disable been removed, as I
suspect it should have, the note should actually say "17, 19, and 20".
So, let's move the FDI RX disable to happen before DDI_BUF_CTL disable,
as that would appear to be the correct order based on the BUN.
Note that Art has since unconfused the spec, and so this patch should
now match the steps listed in the spec.
v2: Add a note that the spec is now correct
Cc: Paulo Zanoni <przanoni@gmail.com>
Cc: Art Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1456841783-4779-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
According to the BSpec update, bit 7 of PORT_CL1CM_DW0 register needs to be
checked to ensure that the register is in accessible state.
Also, based on a BSpec update, changing the timeout value to
check iphypwrgood, from 10ms to wait for up to 100us.
v2: [Ville] use wait_for_us instead of the atomic call.
v3: [Jani/Imre] read register only once
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Reported-by: Philippe Lecluse <Philippe.Lecluse@intel.com>
Cc: Deak, Imre <imre.deak@intel.com>
Cc: Nikula, Jani <jani.nikula@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459446354-19012-1-git-send-email-vandana.kannan@intel.com
The BXT display connections have DSI transcoders A and C that can be
muxed to any pipe, not unlike the eDP transcoder. Add the notion of DSI
transcoders.
The "normal" transcoders A, B and C are not used with BXT DSI, so care
must be taken to avoid accessing those registers with DSI transcoders in
the hardware state readout, modeset, and generally everywhere.
v2: addressing comments by Ville:
- rename the dsi get config function to hsw_get_dsi_transcoder_state
- rebase onto the higher level split of pipe/transcoder functions
- use more has_dsi_encoder as we can now because of the above,
with no need to look at the transcoder so much
- rename IS_DSI_TRANSCODER to transcoder_is_dsi
- use the above a bit more instead of comparing to < TRANSCODER_EDP
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/299740536b7941e31b2744f3ce34f7afe936a771.1458313400.git.jani.nikula@intel.com
Include DPLL0 in the managed dplls for SKL/KBL. While it has to be kept
enabled because of it driving CDCLK, it is better to special case that
inside the DPLL code than in the higher level.
v2: Use INTEL_DPLL_ALWAYS_ON flag. (Ander)
v3: Remove extremely paranoid WARN_ONs. (Maarten)
Handle DPLL0 in skylake_get_ddi_pll() properly. (Ander)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457451987-17466-14-git-send-email-ander.conselvan.de.oliveira@intel.com
Manage the LCPLLs used with DisplayPort, so that all the HSW/BDW DPLLs
are managed by the shared dpll code.
v2: Introduce INTEL_DPLL_ALWAYS_ON flag to please state checker. (Ander)
v3: Initialize pll->flags in intel_shared_dpll_init(). (Ander)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457451987-17466-13-git-send-email-ander.conselvan.de.oliveira@intel.com
Move the code for selecting and configuring HSW/BDW DDI PLLs into the
shared dpll infrastructure. With this most of the PLL selection logic
for those platforms is in one place. DisplayPort is handled separately,
but that should be fixed on a follow up patch. It also allows a small
clean up of the SPLL logic.
v2: Rebase.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457451987-17466-10-git-send-email-ander.conselvan.de.oliveira@intel.com
Change the type of intel_crtc_state->shared_dpll to be a pointer to a
shared dpll. With this there is no need to first convert the id stored
in the crtc state to a pointer in order to use it. It does introduce a
bit of hassle on doing the opposite.
The long term objective is to hide details about dpll ids behind the
shared dpll interface.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457451987-17466-5-git-send-email-ander.conselvan.de.oliveira@intel.com
The recent commit [0bdf5a05647a: drm/i915: Add reverse mapping between
port and intel_encoder] introduced a reverse mapping to retrieve
intel_dig_port object from the port number. The code assumed that the
port vs intel_dig_port are 1:1 mapping. But in reality, this was a
too naive assumption.
As Martin reported about the missing HDMI audio on his SNB machine,
pre-HSW chips may have multiple intel_dig_port objects corresponding
to the same port. Since we assign the mapping statically at the init
time and the multiple objects override the map, it may not match with
the actually enabled output.
This patch tries to address the regression above. The reverse mapping
is provided basically only for the audio callbacks, so now we set /
clear the mapping dynamically at enabling and disabling HDMI/DP audio,
so that we can always track the latest and correct object
corresponding to the given port.
Fixes: 0bdf5a0564 ('drm/i915: Add reverse mapping between port and intel_encoder')
Reported-and-tested-by: Martin Kepplinger <martink@posteo.de>
Cc: drm-intel-fixes@lists.freedesktop.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1456324522-21591-1-git-send-email-tiwai@suse.de
The assumption when adding the intel_display_power_is_enabled() checks
was that if it returns success the power can't be turned off afterwards
during the HW access, which is guaranteed by modeset locks. This isn't
always true, so make sure we hold a dedicated reference for the time of
the access.
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1455296121-4742-8-git-send-email-imre.deak@intel.com
In commit bfb9faab8 we added a workaround for some BXT BIOS that fail to
properly initialize the DDI_A_4_LANES bit of the control register (4
lanes is the only valid configuration on BXT since there is no DDI E to
share with). A recent patch added some additional checks on this
register bit before the workaround gets applied; this breaks eDP on BXT
in some settings. Some minor code shuffling is all we need to restore
the workaround.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Fixes: 7cd87cb80 ("drm/i915: Check max number of lanes when registering DDI ports")
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1454022577-834-1-git-send-email-matthew.d.roper@intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Pull in Dave's drm-next pull request to have a clean base for 4.6.
Also, we need the various atomic state extensions Maarten recently
created.
Conflicts are just adjacent changes that all resolve to nothing in git
diff.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
commit 10afa0b65f ("drm/i915: Reject >9 ddi translation entried if port != A/E on SKL")
added sanity checks to make sure we don't end up with too many ddi translation
values for eDP ports, but it actually failed to check if the port is eDP.
We still look up the edp translations for non-eDP ports, but don't use
them, so we shouldn't be complaining about them either.
Fixes: 10afa0b65f ("drm/i915: Reject >9 ddi translation entried if port != A/E on SKL")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1452612496-9201-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move the ddi buffer translation programming to occur from the encoder
.pre_enable() hook, for just the ddi port we are enabling. Previously
we used to reprogram the translations for all ddi ports during
init and during power well enabling.
v2: s/intel_prepare_ddi_buffers/intel_prepare_ddi_buffer/ (Daniel)
Resolve conflicts due to dev_priv->atomic_cdclk_freq
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make the ddi buffer programming code a bit more neat by passing
around dev_priv instead of dev.
v2: Resolve conflicts due to KBL
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v1)
skl_get_buf_trans_edp() effectively contains another copy of
skl_get_buf_trans_dp(). Remove the duplication and just call
skl_get_buf_trans_dp() from skl_get_buf_trans_edp().
v2: Resolve conflicts due to KBL
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v1)
skl_get_buf_trans_*() don't need the 'ddi_translations' local variable
since all they with is assign and return. Just return the right thing
directly and get rid of the local variable.
v2: Resolve conflicts due to KBL
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v1)
Rather than having open coded checks for the DDI A/E configuration,
just store the max supported lane count in intel_digital_port.
We had an open coded check for DDI A, but not for DDI E. So we may
have been vilating the DDI E max lane count.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No functional changes.
That state the obvious and just duplicate the place we
need to change whenever the table is updated. So let's clean it.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1452021535-22641-1-git-send-email-rodrigo.vivi@intel.com
When debuging an intermittent corrupted screen I suspected on DDI
translation table and checked we are out of date with the spec.
I'm not sure this will fix my bug yet, but it is always good to follow
the spec.
v2: Ville caught a switched i-boost value. Thanks!
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1452021087-21673-1-git-send-email-rodrigo.vivi@intel.com
- fix atomic watermark recomputation logic (Maarten)
- modeset sequence fixes for LPT (Ville)
- more kbl enabling&prep work (Rodrigo, Wayne)
- first bits for mst audio
- page dirty tracking fixes from Dave Gordon
- new get_eld hook from Takashi, also included in the sound tree
- fixup cursor handling when placed at address 0 (Ville)
- refactor VBT parsing code (Jani)
- rpm wakelock debug infrastructure ( Imre)
- fbdev is pinned again (Chris)
- tune the busywait logic to avoid wasting cpu cycles (Chris)
* tag 'drm-intel-next-2015-12-18' of git://anongit.freedesktop.org/drm-intel: (81 commits)
drm/i915: Update DRIVER_DATE to 20151218
drm/i915/skl: Default to noncoherent access up to F0
drm/i915: Only spin whilst waiting on the current request
drm/i915: Limit the busy wait on requests to 5us not 10ms!
drm/i915: Break busywaiting for requests on pending signals
drm/i915: don't enable autosuspend on platforms without RPM support
drm/i915/backlight: prefer dev_priv over dev pointer
drm/i915: Disable primary plane if we fail to reconstruct BIOS fb (v2)
drm/i915: Pin the ifbdev for the info->system_base GGTT mmapping
drm/i915: Set the map-and-fenceable flag for preallocated objects
drm/i915: mdelay(10) considered harmful
drm/i915: check that we are in an RPM atomic section in GGTT PTE updaters
drm/i915: add support for checking RPM atomic sections
drm/i915: check that we hold an RPM wakelock ref before we put it
drm/i915: add support for checking if we hold an RPM reference
drm/i915: use assert_rpm_wakelock_held instead of opencoding it
drm/i915: add assert_rpm_wakelock_held helper
drm/i915: remove HAS_RUNTIME_PM check from RPM get/put/assert helpers
drm/i915: get a permanent RPM reference on platforms w/o RPM support
drm/i915: refactor RPM disabling due to RC6 being disabled
...
This is the "fix igt basic test set issues" edition.
- more PSR fixes from Rodrigo, getting closer
- tons of fifo underrun fixes from Ville
- runtime pm fixes from Imre, Daniel Stone
- fix SDE interrupt handling properly (Jani Nikula)
- hsw/bdw fdi modeset sequence fixes (Ville)
- "don't register bad VGA connectors and fall over" fixes (Ville)
- more fbc fixes from Paulo
- and a grand total of exactly one feature item: Implement dma-buf/fence based
cross-driver sync in the i915 pageflip path (Alex Goins)
* tag 'drm-intel-next-2015-12-04-1' of git://anongit.freedesktop.org/drm-intel: (70 commits)
drm/i915: Update DRIVER_DATE to 20151204
drm/i915/skl: Add SKL GT4 PCI IDs
Revert "drm/i915: Extend LRC pinning to cover GPU context writeback"
drm/i915: Correct the Ref clock value for BXT
drm/i915: Restore skl_gt3 device info
drm/i915: Fix RPS pointer passed from wait_ioctl to i915_wait_request
Revert "drm/i915: Remove superfluous NULL check"
drm/i915: Clean up device info structure definitions
drm/i915: Remove superfluous NULL check
drm/i915: Handle cdclk limits on broadwell.
i915: wait for fence in prepare_plane_fb
i915: wait for fence in mmio_flip_work_func
drm/i915: Extend LRC pinning to cover GPU context writeback
drm/i915/guc: Clean up locks in GuC
drm/i915: only recompress FBC after flushing a drawing operation
drm/i915: get rid of FBC {,de}activation messages
drm/i915: kill fbc.uncompressed_size
drm/i915: use a single intel_fbc_work struct
drm/i915: check for FBC planes in the same place as the pipes
drm/i915: alloc/free the FBC CFB during enable/disable
...
Here are the patchset to add get_eld op to audio component for
communicating more directly between i915 and HD-audio.
Currently, the HDMI/DP audio status and ELD are notified and obtained
via the hardware-level communication over HD-audio unsolicited event
and verbs although the graphics driver holds the exactly same
information. As we already have a notification via audio component,
this is another step forward; namely, the audio driver may fetch
directly the audio status and ELD via the new component op.
The commits are based on Dave's latest drm-next branch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=NShN
-----END PGP SIGNATURE-----
Merge tag 'drm-i915-get-eld' of tiwai/sound into drm-intel-next-queued
Add get_eld audio component for i915/HD-audio
Currently, the HDMI/DP audio status and ELD are notified and obtained
via the hardware-level communication over HD-audio unsolicited event
and verbs although the graphics driver holds the exactly same
information. As we already have a notification via audio component,
this is another step forward; namely, the audio driver may fetch
directly the audio status and ELD via the new component op.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Done with coccinelle for the most part. However, it thinks '...' is
part of the semantic patch, so I put an 'int DOTDOTDOT' placeholder
in its place and got rid of it with sed afterwards.
@@
identifier dev, encoder, funcs;
@@
int drm_encoder_init(struct drm_device *dev,
struct drm_encoder *encoder,
const struct drm_encoder_funcs *funcs,
int encoder_type
+ ,const char *name, int DOTDOTDOT
)
{ ... }
@@
identifier dev, encoder, funcs;
@@
int drm_encoder_init(struct drm_device *dev,
struct drm_encoder *encoder,
const struct drm_encoder_funcs *funcs,
int encoder_type
+ ,const char *name, int DOTDOTDOT
);
@@
expression E1, E2, E3, E4;
@@
drm_encoder_init(E1, E2, E3, E4
+ ,NULL
)
v2: Add ', or NULL...' to @name kernel doc (Jani)
Annotate the function with __printf() attribute (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449670818-2966-1-git-send-email-ville.syrjala@linux.intel.com
This patch adds a reverse mapping from a digital port number to
intel_encoder object containing the corresponding intel_digital_port.
It simplifies the query of the encoder a lot.
Note that, even if it's a valid digital port, the dig_port_map[] might
point still to NULL -- usually it implies a DP MST port. Due to this
fact, the NULL check in each place has no WARN_ON() and just skips the
port. Once when the situation changes in future, we might introduce
WARN_ON() for a more strict check.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds support for DP MST audio in i915.
Enable audio codec when DP MST is enabled if has_audio flag is set.
Disable audio codec when DP MST is disabled if has_audio flag is set.
Another separated patches to support DP MST audio will be implemented
in audio driver.
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Libin Yang <libin.yang@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449036584-105393-2-git-send-email-libin.yang@linux.intel.com
Let's introduce ULT and ULX Kabylake definitions and start
using it for a propper DDI buffer translation.
v2: Remove extra white space. (Paulo)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Currently we disable some parts of FDI setup after a failed link
training. But despite that we continue with the modeset as if everything
is fine. This results in tons of noise from the state checker, and
it means we're not following the proper modeset sequence for the rest of
crtc enabling, nor for crtc disabling.
Ideally we should abort the modeset and follow the proper disable
sequence to shut off everything we enabled so far, but that would
require a big rework of the modeset code. So instead just leave FDI
up and running in its untrained state, and log an error. This is
what we do on older platforms too.
v2: Fix a typo in the commit message
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1449260570-14670-1-git-send-email-ville.syrjala@linux.intel.com
The .get_config() hooks should not reference anything in crtc->config,
everything should be based on the passed in pipe_config instead. So
don't dig out the cpu_transcoder from crtc->config on ddi platfforms,
and also avoid using the encoder->crtc link and instead look up the
pipe via pipe_config->base.crtc.
I don't think this will actually fix anything since during the initial
state readout we set up the encoder->crtc link prior to calling
.get_config(), and during the modeset state check the encoder->crtc
ought to be correct anyway since it's that state we just programmed.
But this seems the right thing to do anyway.
While at it, do some house cleaning on the local variables in the
.infoframe_enabled() hooks.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448555227-31403-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWUmHZAAoJEHm+PkMAQRiGHtcH/RVRsn8re0WdRWYaTr9+Hknm
CGlRJN4LKecttgYQ/2bS1QsDbt8usDPBiiYVopqGXQxPBmjyDAqPjsa+8VzCaVc6
WA+9LDB+PcW28lD6BO+qSZCOAm7hHSZq7dtw9x658IqO+mI2mVeCybsAyunw2iWi
Kf5q90wq6tIBXuT8YH9MXGrSCQw00NclbYeYwB9CmCt9hT/koEFBdl7uFUFitB+Q
GSPTz5fXhgc5Lms85n7flZlrVKoQKmtDQe4/DvKZm+SjsATHU9ru89OxDBdS5gSG
YcEIM4zc9tMjhs3GC9t6WXf6iFOdctum8HOhUoIN/+LVfeOMRRwAhRVqtGJ//Xw=
=DCUg
-----END PGP SIGNATURE-----
Merge tag 'v4.4-rc2' into drm-intel-next-queued
Linux 4.4-rc2
Backmerge to get at
commit 1b0e3a049e
Author: Imre Deak <imre.deak@intel.com>
Date: Thu Nov 5 23:04:11 2015 +0200
drm/i915/skl: disable display side power well support for now
so that we can proplery re-eanble skl power wells in -next.
Conflicts are just adjacent lines changed, except for intel_fbdev.c
where we need to interleave the changs. Nothing nefarious.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Make I915_READ and I915_WRITE more type safe by wrapping the register
offset in a struct. This should eliminate most of the fumbles we've had
with misplaced parens.
This only takes care of normal mmio registers. We could extend the idea
to other register types and define each with its own struct. That way
you wouldn't be able to accidentally pass the wrong thing to a specific
register access function.
The gpio_reg setup is probably the ugliest thing left. But I figure I'd
just leave it for now, and wait for some divine inspiration to strike
before making it nice.
As for the generated code, it's actually a bit better sometimes. Eg.
looking at i915_irq_handler(), we can see the following change:
lea 0x70024(%rdx,%rax,1),%r9d
mov $0x1,%edx
- movslq %r9d,%r9
- mov %r9,%rsi
- mov %r9,-0x58(%rbp)
- callq *0xd8(%rbx)
+ mov %r9d,%esi
+ mov %r9d,-0x48(%rbp)
callq *0xd8(%rbx)
So previously gcc thought the register offset might be signed and
decided to sign extend it, just in case. The rest appears to be
mostly just minor shuffling of instructions.
v2: i915_mmio_reg_{offset,equal,valid}() helpers added
s/_REG/_MMIO/ in the register defines
mo more switch statements left to worry about
ring_emit stuff got sorted in a prep patch
cmd parser, lrc context and w/a batch buildup also in prep patch
vgpu stuff cleaned up and moved to a prep patch
all other unrelated changes split out
v3: Rebased due to BXT DSI/BLC, MOCS, etc.
v4: Rebased due to churn, s/i915_mmio_reg_t/i915_reg_t/
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1447853606-2751-1-git-send-email-ville.syrjala@linux.intel.com
When diagnosing a unrelated bug for someone on irc, it would seem the hardware can
be brought up by the BIOS with the embedded displayport using the SPLL for spread spectrum.
Right now this is not handled well in i915, and it calculates the crtc needs to
be reprogrammed on the first modeset without SSC, but the SPLL itself was kept
active. Fix this by exposing SPLL as a shared pll that will not be returned
by intel_get_shared_dpll; you have to know it exists to use it.
Changes since v1:
- Create a separate dpll_hw_state.spll for spll, and use
separate pll functions for spll.
Tested-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Gabriel Feceoru <gabriel.feceoru@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447681332-6318-1-git-send-email-maarten.lankhorst@linux.intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Before this patch, we used the intel_display_power_{get,put} functions
to make sure the PW1 and Misc I/O power wells were enabled all the
time while LCPLL was enabled. We called a get() at
intel_ddi_pll_init() when we discovered that LCPLL was enabled, then
we would call put/get at skl_{un,}init_cdclk().
The problem is that skl_uninit_cdclk() is indirectly called by
intel_runtime_suspend(). So it will only release its power well
_after_ we already decided to runtime suspend. But since we only
decide to runtime suspend after all power wells and refcounts are
released, that basically means we will never decide to runtime
suspend.
So what this patch does to fix that problem is move the PW1 + Misc I/O
power well handling out of the runtime PM mechanism: instead of
calling intel_display_power_{get_put} - functions that touch the
refcount -, we'll call the low level intel_power_well_{en,dis}able,
which don't change the refcount. This way, it is now possible for the
refcount to actually reach zero, and we'll now start runtime
suspending/resuming.
v2 (from Paulo):
- Write a commit message since the original patch left it empty.
- Rebase after the intel_power_well_{en,dis}able rename.
- Use lookup_power_well() instead of hardcoded indexes.
Testcase: igt/pm_rpm/rte (and every other rpm test)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92211
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92605
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446657859-9598-4-git-send-email-imre.deak@intel.com
While comparing the B-Spec with the code I noticed that several
values in these tables have been updated in the spec, so I
changed the code to match..
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jim Bride <jim.bride@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446852654-883-1-git-send-email-jim.bride@linux.intel.com
The i_boost level in the DDI translation tables are stored per level.
However, skl_ddi_set_iboos() would choose an entry of that table based
on the port argument.
Cc: Jim Bride <jim.bride@linux.intel.com>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Jim Bride <jim.bride@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447247754-802-1-git-send-email-ander.conselvan.de.oliveira@intel.com
The bspec indicates that DDI A using four lanes is the only valid
configuration for Broxton (Broxton doesn't have a DDI E to split these
lanes with); the DDI_A_4_LANES bit of port A's DDI_BUF_CTL should always
be set by the BIOS. However some BIOS versions seem to only be setting
this bit if eDP is actually lit up at boot time; if the BIOS doesn't
turn on the eDP panel because an external display is plugged in, then
this bit is never properly initialized. The end result of this is that
we wind up calculating a lower max data rate than we should and may wind
up rejecting the native mode for panels that we should be able to drive.
Let's workaround this BIOS bug by just turning the DDI_A_4_LANES bit on
in our driver's internal state if we recognize that we're running on BXT
where it should have been on anyway.
Cc: Imre Deak <imre.deak@intel.com>
Cc: Bob Paauwe <bob.j.paauwe@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Bob Paauwe <bob.j.paauwe@intel.com>
Tested-by: Bob Paauwe <bob.j.paauwe@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446764012-27251-1-git-send-email-matthew.d.roper@intel.com
In order to prepare for a link training with DDI, the state machine
would call intel_ddi_prepare_link_retrain(). To remove the dependency to
the hardware information, replace that direct call with a callback.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1445594525-7174-7-git-send-email-ander.conselvan.de.oliveira@intel.com
Kabylake is a Intel® Processor containing Intel® HD Graphics
following Skylake.
It is Gen9p5, so it inherits everything from Skylake.
Let's start by adding the platform separated from Skylake
but reusing most of all features, functions etc. Later we
rebase the PCI-ID patch without is_skylake=1
so we don't replace what original Author did there.
Few IS_SKYLAKEs if statements are not being covered by this patch
on purpose:
- Workarounds: Kabylake is derivated from Skylake H0 so no
W/As apply here.
- GuC: A following patch removes Kabylake support with an
explanation: No firmware available yet.
- DMC/CSR: Done in a separated patch since we need to be carefull
and load the version for revision 7 since
Kabylake is Skylake H0.
v2: relative cleaner commit message and added the missed
IS_KABYLAKE to intel_i2c.c as pointed out by Jani.
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Revision checks are almost always accompanied by a platform check. (The
exceptions are platform specific code.) Add helpers to check for a
platform and a revision range: IS_SKL_REVID() and IS_BXT_REVID(). In
most places this simplifies and clarifies the code. It will be obvious
that revid macros are used for the correct platform.
This should make it easier to find all the revision checks for
workarounds for each platform, and make it easier to remove them once we
drop support for early hardware revisions.
This should also make it easier to differentiate between Skylake and
Kabylake revision checks when Kabylake support is added.
v2: rebase
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1445343722-3312-3-git-send-email-jani.nikula@intel.com
Especially in cases where pre-os does not enable display, cdclk might
not be in sane state. During sanitization initialize cdclk with maximum
value till we get dynamic cdclk support.
v2: Check if BIOS programmed correctly rather than always calling init
- Do validation of programmed cdctl and what it is expected
- Only do slk_init_cdclk if validation failed else reuse BIOS
programmed value
v3: Move the validation logic in a separate sanitize function (Ville)
v4: No need to check LCPLL after sanitize and use max_cdclk_freq instead
of hardcoded value (Ville)
Cc: Imre Deak <imre.deak@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1445344992-14658-1-git-send-email-shobhit.kumar@intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The link training functions had confusing names. The start function
actually does the clock recovery phase of the link training, and the
complete function does the channel equalization. So call them that
instead. Also, every call to intel_dp_start_link_train() was followed
by a call to intel_dp_complete_link_train(), so add a new start
function that calls clock_recory and channel_equalization.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
SKL and BXT qualifies the HAS_DDI() check, and hence haswell
modeset functions are re-used for modeset sequence. But DDI
interface doesn't include support for DSI.
This patch adds:
1. cases for DSI encoder, in those modeset functions and allows
a CRTC modeset
2. Adds call to pre_pll enabled from CRTC modeset function. Nothing
needs to be done as such in CRTC for DSI encoder, as PLL, clock
and and transcoder programming will be taken care in encoder's
pre_enable and pre_pll_enable function.
v2: Fixed Jani's review comments. Added INVALID_PORT for non DDI
encoder like DSI for platforms having HAS_DDI as true.
v3: Rebased on latest drm-nightly branch. Added a WARN_ON for invalid
encoder.
v4: WARN_ON for invalid encoder is refactored as per Jani's suggestion.
Fixed the sequence for pre_pll_enable.
v5: Protected DDI code paths in case of DSI encoder calls.
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Use SKL_DPLLx symbolic names instead of raw numbers
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's more useful to limp on than bring the kernel down. Hitting this is
a more likely event with BXT DSI, although care should be taken not to
call the function for DSI.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bspec update tells that we have to enable oscaledcompmethod instead of
ouniqetrangenmethod for enabling scale value during swing programming.
v2: Adding back 'don't care' values to bxt_ddi_translations_dp and add
error message if ouniquetrangemethod was set (Imre)
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>(v1)
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Adding voltage swing table for edp to support low vswings.
v2: Rebased.
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
FIXME: Should there be a WARN(i != 9) or something, or what does the
entry 9 comment mean?
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Not the first time! not the last time?
There is a possibility to use gcc 5's -Wbool-compare to try and compare
(reg) in those macros to a constant and gcc will warn that the
comparison between a boolean expression and a constant is always either
true or false. Maybe.
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Backmerge -fixes since there's more DDI-E related cleanups on top of
the pile of -fixes for skl that just landed for 4.3.
Conflicts:
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i914/intel_dp.c
drivers/gpu/drm/i915/intel_lrc.c
Conflicts are all fairly harmless adjacent line stuff.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Use port_clock instead of link_bw when picking the PLL parameters for
DP. link_bw may be zero with an eDP 1.4 sink that supports
DP_LINK_RATE_SET so we shouldn't use it for anything other than feed it
to the sink appropriately.
v2: Fix typo in commit message (Sivakumar)
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[Jani: cherry-picked from future.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
With MST there won't be a crtc assigned to the main link encoder, so
trying to dig up the pipe_config from there is a recipe for an oops.
Instead store the parameters (lane_count and link_rate) in the encoder,
and use those values during link training etc. Since those parameters
are now assigned only when the link is actually enabled,
.compute_config() won't clobber them as it did before.
Hardware state readout is still bonkers though as we don't transfer the
link parameters from pipe_config intel_dp. We should do that during
encoder sanitation. But since we don't even do a proper job of reading
out the main link encoder state for MST there's littel point in
worrying about this now.
Fixes a regression with MST caused by:
commit 90a6b7b052
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Mon Jul 6 16:39:15 2015 +0300
drm/i915: Move intel_dp->lane_count into pipe_config
v2: Different apporoach that should keep intel_dp_check_mst_status()
somewhat less oopsy
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reported-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
SKL-Y can now use the same programming for all VccIO values after an
adjustment to I_boost. SKL-U DP table adjustments.
1. Remove SKL Y 0.95V from "SKL H and S" columns in all tables. The
other SKL Y column removes the "0.85V VccIO" so it now applies to all
voltages.
2. DP table changes SKL U 400mV+0db dword 0 value from 2016h to 201Bh.
3. DP table changes SKL U 600mv+0db dword 0 value from 2016h to 201Bh.
4. DP table increases I_boost to level 3 for SKL Y 400mv+9.5db.
v2: Fix compilation warnings as pointed by Paulo.
Reference: Graphics Spec Change r97962
Cc: Arthur Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[Jani: reformatted commit message for shorter lines.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Currently we clobber intel_dp->lane_count in compute config, which means
after a rejected modeset we may no longer be able to retrain the current
link. Move lane_count into pipe_config to avoid that.
v2: Add missing ':' to the pipe config debug dump
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All the *_ddi_pll_select() functions get passed the port_clock and pipe
config as parameters. We only need to pass the pipe config, and the
functions can dig up the port_clock themselves.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use port_clock instead of link_bw when picking the PLL parameters for
DP. link_bw may be zero with an eDP 1.4 sink that supports
DP_LINK_RATE_SET so we shouldn't use it for anything other than feed it
to the sink appropriately.
v2: Fix typo in commit message (Sivakumar)
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
WA for BXT A0/A1, where DDIB's HPD pin is swapped to DDIA, so enabling
DDIA HPD pin in place of DDIB.
v2: For DP, irq_port is used to determine the encoder instead of
hpd_pin and removing the edp HPD logic because port A HPD is not
present(Imre)
v3: Rebased on top of Imre's patchset for enabling HPD on PORT A.
Added hpd_pin swapping for intel_dp_init_connector, setting encoder
for PORT_A as per the WA in irq_port (Imre)
v4: Dont enable interrupt for edp, also reframe the description (Siva)
v5: Don’t check for PORT_A in intel_ddi_init to update dig_port,
instead avoid setting hpd_pin itself (Imre)
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
An OEM may request increased I_boost beyond the recommended values
by specifying an I_boost value to be applied to all swing entries for
a port. These override values are specified in VBT.
v2: rebase and remove unused iboost_bit variable
Issue: VIZ-5676
Signed-off-by: Antti Koskipaa <antti.koskipaa@linux.intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is no correspondent Aux channel for DDI-E.
So we need to rely on VBT to let us know witch one
is being used instead.
v2: Removing some trailing spaces and giving proper
credit to Xiong that added a nice way to avoid port
conflicts by setting supports_dp = 0 when using
equivalent aux for DDI-E.
Credits-to: Xiong Zhang <xiong.y.zhang@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Xiong Zhang <xiong.y.zhang@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drivers/gpu/drm/i915/intel_ddi.c: In function ‘intel_prepare_ddi’:
drivers/gpu/drm/i915/intel_ddi.c:517:6: warning:
‘ddi_translations_fdi’ may be used uninitialized in this function
[-Wmaybe-uninitialized]
if (ddi_translations_fdi)
^
drivers/gpu/drm/i915/intel_ddi.c:446:30: note: ‘ddi_translations_fdi’
was declared here
const struct ddi_buf_trans *ddi_translations_fdi;
^
This line used to be there, but was removed by:
commit f8896f5d58
Author: David Weinehall <david.weinehall@linux.intel.com>
Date: Thu Jun 25 11:11:03 2015 +030
drm/i915/skl: Buffer translation improvements
Cc: David Weinehall <david.weinehall@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch contains changes based on 2 updates to the spec:
Port PLL VCO restriction raised up to 6700.
Port PLL now needs DCO amp override enable for all VCO frequencies.
v2: Sonika's review comment addressed
- dcoampovr_en_h variable not required
Based on a discussion with Siva, the following changes have been made.
- replace dco_amp var with #define BXT_DCO_AMPLITUDE
- set pll10 in a single assignment
v3:
Move DCO amplitude default value to i915_reg.h. Suggested by Siva.
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com> [v2]
[danvet: Spell out BUN since not everyone knows what this means.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Take the HDMI 12bpc mode and pixel repeat into account when extracting
the dotclock from the hardware on DDI platforms.
Tested on HSW only.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-and-tested-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For the purpose of state checking we only care about the DPLL HW flags
that we actually program, so mask off the ones that we don't.
This fixes one set of DPLL state check failures.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add support for reading out the HW state for DDI ports. Since the actual
programming is very similar to the CHV/VLV DPIO PLL programming we can
reuse much of the logic from there.
This fixes the state checker failures I saw on my BXT with HDMI output.
v2:
- rebased on v2 of patch 4/5
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Although we have a fixed setting for the PLL9 and EBB4 registers, it
still makes sense to check them together with the rest of PLL registers.
While at it also remove a redundant comment about 10 bit clock enabling.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch adds support for 0.85V VccIO on Skylake Y,
separate buffer translation tables for Skylake U,
and support for I_boost for the entries that needs this.
Changes in v2:
* Refactored the code a bit to move all DDI signal level setup to
intel_ddi.c
Issue: VIZ-5677
Signed-off-by: David Weinehall <david.weinehall@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
[danvet: Apply style polish checkpatch suggested.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We can't improve a 0 deviation, so when we find such a divider, skip the
remaining ones they won't be better.
This short-circuit the search for 34 of the 373 test frequencies in the
corresponding i-g-t test (tools/skl_compute_wrpll)
v2: Place the short-circuiting code in skl_compute_wrpll() (Paulo)
(I'm sure nobody will notice the spurious removal of a blank line)
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Suggested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently, if an odd divider improves the deviation (minimizes it), we
take that divider. The recommendation is to prefer even dividers.
v2: Move the check at the right place after having inverted the two for
loops in the previous patch.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The HW validation team came back from further testing with a slightly
changed constraint on the deviation between the DCO frequency and the
central frequency. Instead of +-4%, it's now +1%/-6%.
Unfortunately, the previous algorithm didn't quite cope with these new
constraints, the reason being that it wasn't thorough enough looking at
the possible divider candidates.
The new algorithm looks at all dividers, which is definitely a hammer
approach (we could reduce further the set of dividers to good ones as a
follow up, at the cost of a bit more complicated code). But, at least,
we can now satisfy the +1%/+6% rule for all the "Well known" HDMI
frequencies of my test set (373 entries).
On that subject, the new code is quite extensively tested in
intel-gpu-tools (tools/skl_compute_wrpll).
v2: Fix cycling between central frequencies and dividers (Paulo)
Properly choose the minimal deviation between postive and negative
candidates (Paulo).
On the 373 test frequencies, v2 computes better dividers than v1 (ie
more even dividers and lower deviation on average):
v1: average deviation: 206.52
v2: average deviation: 194.47
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
According to bspec the DDI PHY vswing scale value is "don't care" in
case the scale enable bit [27] is clear. But this doesn't seem to be
correct. The scale value seems to also matter if the scale mode bit
[26] is set. So both bit 26 and 27 depend on the value. Setting the
scale value to 0 while either bit is set results in a failed modeset on
HDMI (sink reports no signal).
After reset the scale value is 0x98, but according to the spec we have
to program it to 0x9a. So for consistency program it always to 0x9a
regardless of the scale enable bit.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Tested-by: Matt Roper <matthew.d.roper@intel.com>
Acked-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
intel_update_cdclk() will already display the boot CDCLK for DDI
platforms, no need to repeat there.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
BXT supports following intermediate link rates for edp:
2.16GHz, 2.43GHz, 3.24GHz, 4.32GHz.
Adding support for programming the intermediate rates.
v2: Adding clock in bxt_clk_div struct and then look for the entry with
required rate (Ville)
v3: 'clock' has the selected value, no need to use link_bw or rate_select
for selecting pll(Ville)
v4: Make bxt_dp_clk_val const and remove size (Ville)
v5: Rebased
v6: Removed setting of vco while rebasing in v5, adding it back
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v4)
Reviewed-by: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The orignal code started by storing the actual central frequency (in Hz,
using a uint64_t) in a uint32_t which codes for the register value. That
can't be right.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Those functions were the only one in existence when they were
introduced. We now know they are only valid for HSW/BDW.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
abs_diff() properly protects its parameters, so no need for the outer ()
here.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Imre Deak