Tegra186+ hangs if host1x hardware is disabled at a kernel boot time
because we touch hardware before runtime PM is resumed. Move sync point
assignment initialization to the RPM-resume callback. Older SoCs were
unaffected because they skip that sync point initialization.
Tested-by: Jon Hunter <jonathanh@nvidia.com> # T186
Reported-by: Jon Hunter <jonathanh@nvidia.com> # T186
Fixes: 6b6776e2ab ("gpu: host1x: Add initial runtime PM and OPP support")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Host1x DMA buffer isn't mapped properly when CONFIG_ARM_DMA_USE_IOMMU=y.
The memory management code of Host1x driver has a longstanding overhaul
overdue and it's not obvious where the problem is in this case. Hence
let's add back the old workaround which we already had sometime before.
It explicitly detaches Host1x device from the offending implicit IOMMU
domain. This fixes a completely broken Host1x DMA in case of ARM32
multiplatform kernel config.
Cc: stable@vger.kernel.org
Fixes: af1cbfb9bf ("gpu: host1x: Support DMA mapping of buffers")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add host1x_channel_stop() which waits till channel becomes idle and then
stops the channel hardware. This is needed for supporting suspend/resume
by host1x drivers since the hardware state is lost after power-gating,
thus the channel needs to be stopped before client enters into suspend.
Tested-by: Peter Geis <pgwipeout@gmail.com> # Ouya T30
Tested-by: Paul Fertser <fercerpav@gmail.com> # PAZ00 T20
Tested-by: Nicolas Chauvet <kwizart@gmail.com> # PAZ00 T20 and TK1 T124
Tested-by: Matt Merhar <mattmerhar@protonmail.com> # Ouya T30
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add runtime PM and OPP support to the Host1x driver. For the starter we
will keep host1x always-on because dynamic power management require a major
refactoring of the driver code since lot's of code paths are missing the
RPM handling and we're going to remove some of these paths in the future.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Peter Geis <pgwipeout@gmail.com> # Ouya T30
Tested-by: Paul Fertser <fercerpav@gmail.com> # PAZ00 T20
Tested-by: Nicolas Chauvet <kwizart@gmail.com> # PAZ00 T20 and TK1 T124
Tested-by: Matt Merhar <mattmerhar@protonmail.com> # Ouya T30
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Host1x seems to be relying on picking up dma-mapping.h transitively from
iova.h, which has no reason to include it in the first place. Fix the
former issue before we totally break things by fixing the latter one.
CC: Thierry Reding <thierry.reding@gmail.com>
CC: Mikko Perttunen <mperttunen@nvidia.com>
CC: dri-devel@lists.freedesktop.org
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add support for booting and using NVDEC on Tegra210, Tegra186
and Tegra194 to the Host1x and TegraDRM drivers. Booting in
secure mode is not currently supported.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This cache is used to avoid mapping and unmapping buffer objects
unnecessarily. Mappings are cached per client and stay hot until
the buffer object is destroyed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
DMA-BUF requires that each device that accesses a DMA-BUF attaches to it
separately. To do so the host1x_bo_pin() and host1x_bo_unpin() functions
need to be reimplemented so that they can return a mapping, which either
represents an attachment or a map of the driver's own GEM object.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The memory allocated for a DMA fence could be leaked if the code failed
to allocate the waiter object. Make sure to release the fence allocation
on failure.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DEFINE_SPINLOCK macro creates a global spinlock symbol that is visible
to the whole kernel. This is unintended in the code, fix it.
Fixes: 687db2207b ("gpu: host1x: Add DMA fence implementation")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Show the values of the DMASTART and DMAEND registers when dumping status
to help with failure analysis.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Dumping the full CDMA push buffer takes a long time and isn't very
useful since most of the contents are not relevant. Instead only show
the CDMA push buffer entries associated with current jobs.
While at it, tweak the indentation a bit to make the output more
readable.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The host1x debug code uses a mix of phys_addr_t, dma_addr_t and u32 to
represent addresses. However, these addresses are always DMA addresses
so use the appropriate type.
This fixes some issues with how these addresses are displayed, because
they could be truncated in some cases and not show the full address.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The new UAPI will have its own firewall, and we don't want to run
the firewall in the Host1x driver for those jobs. As such, add a
parameter to host1x_job_alloc to specify if we want to skip the
firewall in the Host1x driver.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add support for inserting syncpoint waits in the CDMA pushbuffer.
These waits need to be done in HOST1X class, while gather submitted
by the application execute in engine class.
Support is added by converting the gather list of job into a command
list that can include both gathers and waits. When the job is
submitted, these commands are pushed as the appropriate opcodes
on the CDMA pushbuffer.
Also supported are waits relative to the start of the job,
which are useful for jobs doing multiple things with an engine
that doesn't natively support pipelining.
While at it, use 32-bit waits on chips that support them.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add a callback field to the job structure, to be called just before
the job is to be freed. This allows the job's submitter to clean
up any of its own state, like decrement runtime PM refcounts.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add a new property for jobs to enable or disable recovery i.e.
CPU increments of syncpoints to max value on job timeout. This
allows for a more solid model for hanged jobs, where userspace
doesn't need to guess if a syncpoint increment happened because
the job completed, or because job timeout was triggered.
On job timeout, we stop the channel, NOP all future jobs on the
channel using the same syncpoint, mark the syncpoint as locked
and resume the channel from the next job, if any.
The future jobs are NOPed, since because we don't do the CPU
increments, the value of the syncpoint is no longer synchronized,
and any waiters would become confused if a future job incremented
the syncpoint. The syncpoint is marked locked to ensure that any
future jobs cannot increment the syncpoint either, until the
application has recognized the situation and reallocated the
syncpoint.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add an implementation of dma_fences based on syncpoints. Syncpoint
interrupts are used to signal fences. Additionally, after
software signaling has been enabled, a 30 second timeout is started.
If the syncpoint threshold is not reached within this period,
the fence is signalled with an -ETIMEDOUT error code. This is to
allow fences that would never reach their syncpoint threshold to
be cleaned up. The timeout can potentially be removed in the future
after job tracking code has been refactored.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
In some cases we may need to initialize the host1x client first before
registering it. This commit adds a new helper that will do nothing but
the initialization of the data structure.
At the same time, the initialization is removed from the registration
function. Note, however, that for simplicity we explicitly initialize
the client when the host1x_client_register() function is called, as
opposed to the low-level __host1x_client_register() function. This
allows existing callers to remain unchanged.
Signed-off-by: Thierry Reding <treding@nvidia.com>
These callbacks can be used by client drivers to run code during early
init and during late exit. Early init callbacks are run prior to the
regular init callbacks while late exit callbacks run after the regular
exit callbacks.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Syncpoint interrupts are not working as expected on Tegra194. The
problem is that the syncpoint interrupt threshold being used is the
global interrupt threshold and not the virtual interrupt threshold.
Fix this by using the virtual interrupt threshold which aligns with
downstream.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Move the assignment of the ref out-pointer in host1x_intr_add_action
to happen within the spinlock. With the current arrangement,
it is possible for the waiter to complete before the assignment
has happened, which breaks horribly if the waiter completion
callback tries to use the reference.
In practice, there is currently no situation where this issue can
manifest -- it was first noticed with the upcoming DMA fence
implementation patches. As such this doesn't need to be backported.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
On T20-T148 chips, the bootloader can set up a boot splash
screen with DC configured to increment syncpoint 26/27
at VBLANK. Because of this we shouldn't allow these syncpoints
to be allocated until DC has been reset and will no longer
increment them in the background.
As such, on these chips, reserve those two syncpoints at
initialization, and only mark them free once the DC
driver has indicated it's safe to do so.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
With job recovery becoming optional, syncpoints may have a mismatch
between their value and max value when freed. As such, when freeing,
set the max value to the current value of the syncpoint so that it
is in a sane state for the next user.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add reference counting for allocated syncpoints to allow keeping
them allocated while jobs are referencing them. Additionally,
clean up various places using syncpoint IDs to use host1x_syncpt
pointers instead.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Make syncpoint expiration checks always use the same logic used by
the hardware. This ensures that there are no race conditions that
could occur because of the hardware triggering a syncpoint interrupt
and then the driver disagreeing.
One situation where this could occur is if a job incremented a
syncpoint too many times -- then the hardware would trigger an
interrupt, but the driver would assume that a syncpoint value
greater than the syncpoint's max value is in the future, and not
clean up the job.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Before this patch, cancelled waiters would only be cleaned up
once their threshold value was reached. Make host1x_intr_put_ref
process the cancellation immediately to fix this.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Show the number of pending waiters in the debugfs status file.
This is useful for testing to verify that waiters do not leak
or accumulate incorrectly.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Syncpoints don't need to be associated with any client,
so remove the property, and expose host1x_syncpt_alloc.
This will allow allocating syncpoints without prior knowledge
of the engine that it will be used with.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
To avoid false lockdep warnings, give each client lock a different
lock class, passed from the initialization site by macro.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
New driver:
Cadence MHDP8546 DisplayPort bridge driver
core:
- cross-driver scatterlist cleanups
- devm_drm conversions
- remove drm_dev_init
- devm_drm_dev_alloc conversion
ttm:
- lots of refactoring and cleanups
bridges:
- chained bridge support in more drivers
panel:
- misc new panels
scheduler:
- cleanup priority levels
displayport:
- refactor i915 code into helpers for nouveau
i915:
- split into display and GT trees
- WW locking refactoring in GEM
- execbuf2 extension mechanism
- syncobj timeline support
- GEN 12 HOBL display powersaving
- Rocket Lake display additions
- Disable FBC on Tigerlake
- Tigerlake Type-C + DP improvements
- Hotplug interrupt refactoring
amdgpu:
- Sienna Cichlid updates
- Navy Flounder updates
- DCE6 (SI) support for DC
- Plane rotation enabled
- TMZ state info ioctl
- PCIe DPC recovery support
- DC interrupt handling refactor
- OLED panel fixes
amdkfd:
- add SMI events for thermal throttling
- SMI interface events ioctl update
- process eviction counters
radeon:
- move to dma_ for allocations
- expose sclk via sysfs
msm:
- DSI support for sm8150/sm8250
- per-process GPU pagetable support
- Displayport support
mediatek:
- move HDMI phy driver to PHY
- convert mtk-dpi to bridge API
- disable mt2701 tmds
tegra:
- bridge support
exynos:
- misc cleanups
vc4:
- dual display cleanups
ast:
- cleanups
gma500:
- conversion to GPIOd API
hisilicon:
- misc reworks
ingenic:
- clock handling and format improvements
mcde:
- DSI support
mgag200:
- desktop g200 support
mxsfb:
- i.MX7 + i.MX8M
- alpha plane support
panfrost:
- devfreq support
- amlogic SoC support
ps8640:
- EDID from eDP retrieval
tidss:
- AM65xx YUV workaround
virtio:
- virtio-gpu exported resources
rcar-du:
- R8A7742, R8A774E1 and R8A77961 support
- YUV planar format fixes
- non-visible plane handling
- VSP device reference count fix
- Kconfig fix to avoid displaying disabled options in .config
-----BEGIN PGP SIGNATURE-----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=4H8J
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2020-10-15' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"Not a major amount of change, the i915 trees got split into display
and gt trees to better facilitate higher level review, and there's a
major refactoring of i915 GEM locking to use more core kernel concepts
(like ww-mutexes). msm gets per-process pagetables, older AMD SI cards
get DC support, nouveau got a bump in displayport support with common
code extraction from i915.
Outside of drm this contains a couple of patches for hexint
moduleparams which you've acked, and a virtio common code tree that
you should also get via it's regular path.
New driver:
- Cadence MHDP8546 DisplayPort bridge driver
core:
- cross-driver scatterlist cleanups
- devm_drm conversions
- remove drm_dev_init
- devm_drm_dev_alloc conversion
ttm:
- lots of refactoring and cleanups
bridges:
- chained bridge support in more drivers
panel:
- misc new panels
scheduler:
- cleanup priority levels
displayport:
- refactor i915 code into helpers for nouveau
i915:
- split into display and GT trees
- WW locking refactoring in GEM
- execbuf2 extension mechanism
- syncobj timeline support
- GEN 12 HOBL display powersaving
- Rocket Lake display additions
- Disable FBC on Tigerlake
- Tigerlake Type-C + DP improvements
- Hotplug interrupt refactoring
amdgpu:
- Sienna Cichlid updates
- Navy Flounder updates
- DCE6 (SI) support for DC
- Plane rotation enabled
- TMZ state info ioctl
- PCIe DPC recovery support
- DC interrupt handling refactor
- OLED panel fixes
amdkfd:
- add SMI events for thermal throttling
- SMI interface events ioctl update
- process eviction counters
radeon:
- move to dma_ for allocations
- expose sclk via sysfs
msm:
- DSI support for sm8150/sm8250
- per-process GPU pagetable support
- Displayport support
mediatek:
- move HDMI phy driver to PHY
- convert mtk-dpi to bridge API
- disable mt2701 tmds
tegra:
- bridge support
exynos:
- misc cleanups
vc4:
- dual display cleanups
ast:
- cleanups
gma500:
- conversion to GPIOd API
hisilicon:
- misc reworks
ingenic:
- clock handling and format improvements
mcde:
- DSI support
mgag200:
- desktop g200 support
mxsfb:
- i.MX7 + i.MX8M
- alpha plane support
panfrost:
- devfreq support
- amlogic SoC support
ps8640:
- EDID from eDP retrieval
tidss:
- AM65xx YUV workaround
virtio:
- virtio-gpu exported resources
rcar-du:
- R8A7742, R8A774E1 and R8A77961 support
- YUV planar format fixes
- non-visible plane handling
- VSP device reference count fix
- Kconfig fix to avoid displaying disabled options in .config"
* tag 'drm-next-2020-10-15' of git://anongit.freedesktop.org/drm/drm: (1494 commits)
drm/ingenic: Fix bad revert
drm/amdgpu: Fix invalid number of character '{' in amdgpu_acpi_init
drm/amdgpu: Remove warning for virtual_display
drm/amdgpu: kfd_initialized can be static
drm/amd/pm: setup APU dpm clock table in SMU HW initialization
drm/amdgpu: prevent spurious warning
drm/amdgpu/swsmu: fix ARC build errors
drm/amd/display: Fix OPTC_DATA_FORMAT programming
drm/amd/display: Don't allow pstate if no support in blank
drm/panfrost: increase readl_relaxed_poll_timeout values
MAINTAINERS: Update entry for st7703 driver after the rename
Revert "gpu/drm: ingenic: Add option to mmap GEM buffers cached"
drm/amd/display: HDMI remote sink need mode validation for Linux
drm/amd/display: Change to correct unit on audio rate
drm/amd/display: Avoid set zero in the requested clk
drm/amdgpu: align frag_end to covered address space
drm/amdgpu: fix NULL pointer dereference for Renoir
drm/vmwgfx: fix regression in thp code due to ttm init refactor.
drm/amdgpu/swsmu: add interrupt work handler for smu11 parts
drm/amdgpu/swsmu: add interrupt work function
...
The Documentation/DMA-API-HOWTO.txt states that the dma_map_sg() function
returns the number of the created entries in the DMA address space.
However the subsequent calls to the dma_sync_sg_for_{device,cpu}() and
dma_unmap_sg must be called with the original number of the entries
passed to the dma_map_sg().
struct sg_table is a common structure used for describing a non-contiguous
memory buffer, used commonly in the DRM and graphics subsystems. It
consists of a scatterlist with memory pages and DMA addresses (sgl entry),
as well as the number of scatterlist entries: CPU pages (orig_nents entry)
and DMA mapped pages (nents entry).
It turned out that it was a common mistake to misuse nents and orig_nents
entries, calling DMA-mapping functions with a wrong number of entries or
ignoring the number of mapped entries returned by the dma_map_sg()
function.
To avoid such issues, lets use a common dma-mapping wrappers operating
directly on the struct sg_table objects and use scatterlist page
iterators where possible. This, almost always, hides references to the
nents and orig_nents entries, making the code robust, easier to follow
and copy/paste safe.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
With the split of MIPI calibration into tegra_mipi_calibrate() and
tegra_mipi_wait(), MIPI clock is not kept enabled and mutex is not locked
till the calibration is done.
So, this patch keeps MIPI clock enabled and mutex locked after triggering
start of calibration till its done.
To let calibration process go through its finite sequence codes before
calibration logic waiting for pads idle state added wait time of 75usec
to make sure it sees idle state to apply the results.
This patch renames tegra_mipi_calibrate() as tegra_mipi_start_calibration()
and tegra_mipi_wait() as tegra_mipi_finish_calibration() to be inline
with their usage.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When job hangs and there is a memory error pointing at channel's push
buffer, it is very handy to know the push buffer's state. This patch
makes the push buffer's state to be dumped into KMSG in addition to the
job's gathers.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Once channel's job is hung, it dumps the channel's state into KMSG before
tearing down the offending job. If multiple channels hang at once, then
they dump messages simultaneously, making the debug info unreadable, and
thus, useless. This patch adds mutex which allows only one channel to emit
debug messages at a time.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This patch fixes gather's BO refcounting on a pinning error. Gather's BO
won't be leaked now if something goes wrong.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
We don't need to hold and pin original BOs of the gathers in a case of
enabled firewall because in this case gather's content is copied and the
copy is used by the executed job.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
SW can trigger MIPI pads calibration any time after power on
but calibration results will be latched and applied to the pads
by MIPI CAL unit only when the link is in LP-11 state and then
status register will be updated.
For CSI, trigger of pads calibration happen during CSI stream
enable where CSI receiver is kept ready prior to sensor or CSI
transmitter stream start.
So, pads may not be in LP-11 at this time and waiting for the
calibration to be done immediate after calibration start will
result in timeout.
This patch splits tegra_mipi_calibrate() and tegra_mipi_wait()
so triggering for calibration and waiting for it to complete can
happen at different stages.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use readl_relaxed_poll_timeout() in tegra_mipi_wait() to simplify
the code.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra CSI driver need a separate MIPI device for each channel as
calibration of corresponding MIPI pads for each channel should
happen independently.
So, this patch updates tegra_mipi_request() API to add a device_node
pointer argument to allow creating mipi device for specific device
node rather than a device.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Currently when a host1x device driver is unregistered, it is not
detached from the host1x controller, which means that the device
will stay around and when the driver is registered again, it may
bind to the old, stale device rather than the new one that was
created from scratch upon driver registration. This in turn can
cause various weird crashes within the driver core because it is
confronted with a device that was already deleted.
Fix this by detaching the driver from the host1x controller when
it is unregistered. This ensures that the deleted device also is
no longer present in the device list that drivers will bind to.
Reported-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tested-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
In order to remove the dependency on the simple-bus compatible string,
which causes the OF driver core to register all child devices, make the
host1x driver explicitly register its children.
Signed-off-by: Thierry Reding <treding@nvidia.com>
host1x_debug_init() must be reverted in an error handling path.
This is already fixed in the remove function since commit 44156eee91
("gpu: host1x: Clean up debugfs on removal")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra124 and Tegra210 support addressing more than 32 bits of physical
memory. However, since their host1x does not support the wide GATHER
opcode, they should use the SMMU if at all possible to ensure that all
the system memory can be used for command buffers, irrespective of
whether or not the host1x firewall is enabled.
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
When testing whether or not to enable the use of the SMMU, consult the
supported DMA mask rather than the actually configured DMA mask, since
the latter might already have been restricted.
Fixes: 2d9384ff91 ("drm/tegra: Relax IOMMU usage criteria on old Tegra")
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
These are a couple of quick fixes for regressions that were found during
the first two weeks of the merge window.
-----BEGIN PGP SIGNATURE-----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=W1SC
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-5.6-rc1-fixes' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Fixes for v5.6-rc1
These are a couple of quick fixes for regressions that were found during
the first two weeks of the merge window.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thierry Reding <thierry.reding@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200206172753.2185390-1-thierry.reding@gmail.com
The DMA direction is only used by the DMA API, so there is no use in
setting it when a buffer object isn't mapped with the DMA API.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
This partially reverts the DMA API support that was recently merged
because it was causing performance regressions on older Tegra devices.
Unfortunately, the cache maintenance performed by dma_map_sg() and
dma_unmap_sg() causes performance to drop by a factor of 10.
The right solution for this would be to cache mappings for buffers per
consumer device, but that's a bit involved. Instead, we simply revert to
the old behaviour of sharing IOVA mappings when we know that devices can
do so (i.e. they share the same IOMMU domain).
Cc: <stable@vger.kernel.org> # v5.5
Reported-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
This contains a small set of mostly fixes and some minor improvements.
-----BEGIN PGP SIGNATURE-----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=OBEv
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-5.6-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v5.6-rc1
This contains a small set of mostly fixes and some minor improvements.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thierry Reding <thierry.reding@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200111004835.2412858-1-thierry.reding@gmail.com
platform_get_irq() will call dev_err() itself on failure,
so there is no need for the driver to also do this.
This is detected by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Tegra DRM driver heavily relies on the implementations for runtime
suspend/resume to be called at specific times. Unfortunately, there are
some cases where that doesn't work. One example is if the user disables
runtime PM for a given subdevice. Another example is that the PM core
acquires a reference to runtime PM during system sleep, effectively
preventing devices from going into low power modes. This is intentional
to avoid nasty race conditions, but it also causes system sleep to not
function properly on all Tegra systems.
Fix this by not implementing runtime PM at all. Instead, a minimal,
reference-counted suspend/resume infrastructure is added to the host1x
bus. This has the benefit that it can be used regardless of the system
power state (or any transitions we might be in), or whether or not the
user allows runtime PM.
Atomic modesetting guarantees that these functions will end up being
called at the right point in time, so the pitfalls for the more generic
runtime PM do not apply here.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Rename the host1x clients' parent to "host" because that more closely
describes what it is. The parent can be confused with the parent device
in terms of the device hierarchy. Subsequent patches will add a new
member that refers to the parent in that hierarchy.
Signed-off-by: Thierry Reding <treding@nvidia.com>
UAPI Changes:
- Add support for DMA-BUF HEAPS.
Cross-subsystem Changes:
- mipi dsi definition updates, pulled into drm-intel as well.
- Add lockdep annotations for dma_resv vs mmap_sem and fs_reclaim.
- Remove support for dma-buf kmap/kunmap.
- Constify fb_ops in all fbdev drivers, including drm drivers and drm-core, and media as well.
Core Changes:
- Small cleanups to ttm.
- Fix SCDC definition.
- Assorted cleanups to core.
- Add todo to remove load/unload hooks, and use generic fbdev emulation.
- Assorted documentation updates.
- Use blocking ww lock in ttm fault handler.
- Remove drm_fb_helper_fbdev_setup/teardown.
- Warning fixes with W=1 for atomic.
- Use drm_debug_enabled() instead of drm_debug flag testing in various drivers.
- Fallback to nontiled mode in fbdev emulation when not all tiles are present. (Later on reverted)
- Various kconfig indentation fixes in core and drivers.
- Fix freeing transactions in dp-mst correctly.
- Sean Paul is steping down as core maintainer. :-(
- Add lockdep annotations for atomic locks vs dma-resv.
- Prevent use-after-free for a bad job in drm_scheduler.
- Fill out all block sizes in the P01x and P210 definitions.
- Avoid division by zero in drm/rect, and fix bounds.
- Add drm/rect selftests.
- Add aspect ratio and alternate clocks for HDMI 4k modes.
- Add todo for drm_framebuffer_funcs and fb_create cleanup.
- Drop DRM_AUTH for prime import/export ioctls.
- Clear DP-MST payload id tables downstream when initializating.
- Fix for DSC throughput definition.
- Add extra FEC definitions.
- Fix fake offset in drm_gem_object_funs.mmap.
- Stop using encoder->bridge in core directly
- Handle bridge chaining slightly better.
- Add backlight support to drm/panel, and use it in many panel drivers.
- Increase max number of y420 modes from 128 to 256, as preparation to add the new modes.
Driver Changes:
- Small fixes all over.
- Fix documentation in vkms.
- Fix mmap_sem vs dma_resv in nouveau.
- Small cleanup in komeda.
- Add page flip support in gma500 for psb/cdv.
- Add ddc symlink in the connector sysfs directory for many drivers.
- Add support for analogic an6345, and fix small bugs in it.
- Add atomic modesetting support to ast.
- Fix radeon fault handler VMA race.
- Switch udl to use generic shmem helpers.
- Unconditional vblank handling for mcde.
- Miscellaneous fixes to mcde.
- Tweak debug output from komeda using debugfs.
- Add gamma and color transform support to komeda for DOU-IPS.
- Add support for sony acx424AKP panel.
- Various small cleanups to gma500.
- Use generic fbdev emulation in udl, and replace udl_framebuffer with generic implementation.
- Add support for Logic PD Type 28 panel.
- Use drm_panel_* wrapper functions in exynos/tegra/msm.
- Add devicetree bindings for generic DSI panels.
- Don't include drm_pci.h directly in many drivers.
- Add support for begin/end_cpu_access in udmabuf.
- Stop using drm_get_pci_dev in gma500 and mga200.
- Fixes to UDL damage handling, and use dma_buf_begin/end_cpu_access.
- Add devfreq thermal support to panfrost.
- Fix hotplug with daisy chained monitors by removing VCPI when disabling topology manager.
- meson: Add support for OSD1 plane AFBC commit.
- Stop displaying garbage when toggling ast primary plane on/off.
- More cleanups and fixes to UDL.
- Add D32 suport to komeda.
- Remove globle copy of drm_dev in gma500.
- Add support for Boe Himax8279d MIPI-DSI LCD panel.
- Add support for ingenic JZ4770 panel.
- Small null pointer deference fix in ingenic.
- Remove support for the special tfp420 driver, as there is a generic way to do it.
-----BEGIN PGP SIGNATURE-----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=b15X
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2019-12-16' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.6:
UAPI Changes:
- Add support for DMA-BUF HEAPS.
Cross-subsystem Changes:
- mipi dsi definition updates, pulled into drm-intel as well.
- Add lockdep annotations for dma_resv vs mmap_sem and fs_reclaim.
- Remove support for dma-buf kmap/kunmap.
- Constify fb_ops in all fbdev drivers, including drm drivers and drm-core, and media as well.
Core Changes:
- Small cleanups to ttm.
- Fix SCDC definition.
- Assorted cleanups to core.
- Add todo to remove load/unload hooks, and use generic fbdev emulation.
- Assorted documentation updates.
- Use blocking ww lock in ttm fault handler.
- Remove drm_fb_helper_fbdev_setup/teardown.
- Warning fixes with W=1 for atomic.
- Use drm_debug_enabled() instead of drm_debug flag testing in various drivers.
- Fallback to nontiled mode in fbdev emulation when not all tiles are present. (Later on reverted)
- Various kconfig indentation fixes in core and drivers.
- Fix freeing transactions in dp-mst correctly.
- Sean Paul is steping down as core maintainer. :-(
- Add lockdep annotations for atomic locks vs dma-resv.
- Prevent use-after-free for a bad job in drm_scheduler.
- Fill out all block sizes in the P01x and P210 definitions.
- Avoid division by zero in drm/rect, and fix bounds.
- Add drm/rect selftests.
- Add aspect ratio and alternate clocks for HDMI 4k modes.
- Add todo for drm_framebuffer_funcs and fb_create cleanup.
- Drop DRM_AUTH for prime import/export ioctls.
- Clear DP-MST payload id tables downstream when initializating.
- Fix for DSC throughput definition.
- Add extra FEC definitions.
- Fix fake offset in drm_gem_object_funs.mmap.
- Stop using encoder->bridge in core directly
- Handle bridge chaining slightly better.
- Add backlight support to drm/panel, and use it in many panel drivers.
- Increase max number of y420 modes from 128 to 256, as preparation to add the new modes.
Driver Changes:
- Small fixes all over.
- Fix documentation in vkms.
- Fix mmap_sem vs dma_resv in nouveau.
- Small cleanup in komeda.
- Add page flip support in gma500 for psb/cdv.
- Add ddc symlink in the connector sysfs directory for many drivers.
- Add support for analogic an6345, and fix small bugs in it.
- Add atomic modesetting support to ast.
- Fix radeon fault handler VMA race.
- Switch udl to use generic shmem helpers.
- Unconditional vblank handling for mcde.
- Miscellaneous fixes to mcde.
- Tweak debug output from komeda using debugfs.
- Add gamma and color transform support to komeda for DOU-IPS.
- Add support for sony acx424AKP panel.
- Various small cleanups to gma500.
- Use generic fbdev emulation in udl, and replace udl_framebuffer with generic implementation.
- Add support for Logic PD Type 28 panel.
- Use drm_panel_* wrapper functions in exynos/tegra/msm.
- Add devicetree bindings for generic DSI panels.
- Don't include drm_pci.h directly in many drivers.
- Add support for begin/end_cpu_access in udmabuf.
- Stop using drm_get_pci_dev in gma500 and mga200.
- Fixes to UDL damage handling, and use dma_buf_begin/end_cpu_access.
- Add devfreq thermal support to panfrost.
- Fix hotplug with daisy chained monitors by removing VCPI when disabling topology manager.
- meson: Add support for OSD1 plane AFBC commit.
- Stop displaying garbage when toggling ast primary plane on/off.
- More cleanups and fixes to UDL.
- Add D32 suport to komeda.
- Remove globle copy of drm_dev in gma500.
- Add support for Boe Himax8279d MIPI-DSI LCD panel.
- Add support for ingenic JZ4770 panel.
- Small null pointer deference fix in ingenic.
- Remove support for the special tfp420 driver, as there is a generic way to do it.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ba73535a-9334-5302-2e1f-5208bd7390bd@linux.intel.com
A few reasons to drop kmap:
- For native objects all we do is look at obj->vaddr anyway, so might
as well not call functions for every page.
- Reloc-processing on dma-buf is ... questionable.
- Plus most dma-buf that bother kernel cpu mmaps give you at least
vmap, much less kmaps. And all the ones relevant for arm-soc are
again doing a obj->vaddr game anyway, there's no real kmap going on
on arm it seems.
Plus this seems to be the only real in-tree user of dma_buf_kmap, and
I'd like to get rid of that.
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-tegra@vger.kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20191118103536.17675-2-daniel.vetter@ffwll.ch
Currently configurations can be generated where IOMMU_SUPPORT is
disabled but IOMMU_IOVA is built as a module and HOST1X as built-in. In
such a case, the symbols guarded by IOMMU_IOVA will not be available
when linking the host1x driver and cause a linking failure.
Simplify this by unconditionally selecting IOMMU_IOVA, which makes sure
that it will be forced to =y if HOST1X=y. Technically we can now get
IOMMU_IOVA code built-in even if we don't use it (host1x only uses it
when IOMMU_SUPPORT is also enabled), but such configuration are of a
mostly academic nature. In all practical configurations we want IOMMU
support anyway.
Signed-off-by: Thierry Reding <treding@nvidia.com>
If the Tegra DRM clients are backed by an IOMMU, push buffers are likely
to be allocated beyond the 32-bit boundary if sufficient system memory
is available. This is problematic on earlier generations of Tegra where
host1x supports a maximum of 32 address bits for the GATHER opcode. More
recent versions of Tegra (Tegra186 and later) have a wide variant of the
GATHER opcode, which allows addressing up to 64 bits of memory.
If host1x itself is behind an IOMMU as well this doesn't matter because
the IOMMU's input address space is restricted to 32 bits on generations
without support for wide GATHER opcodes.
However, if host1x is not behind an IOMMU, it won't be able to process
push buffers beyond the 32-bit boundary on Tegra generations that don't
support wide GATHER opcodes. Restrict the DMA mask to 32 bits on these
generations prevents buffers from being allocated from beyond the 32-bit
boundary.
Signed-off-by: Thierry Reding <treding@nvidia.com>
If host1x_bo_pin() returns an SG table, create a DMA mapping for the
buffer. For buffers that the host1x client has already mapped itself,
host1x_bo_pin() returns NULL and the existing DMA address is used.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Currently when the gather buffers are copied, they are copied to a
buffer that is allocated for the host1x client that wants to execute the
command streams in the buffers. However, the gather buffers will be read
by the host1x device, which causes SMMU faults if the DMA API is backed
by an IOMMU.
Fix this by allocating the gather buffer copy for the host1x device,
which makes sure that it will be mapped into the host1x's IOVA space if
the DMA API is backed by an IOMMU.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The debugfs files created for host1x are never removed, causing these
files to be left dangling in debugfs. This results in a crash when any
of these files are accessed after the host1x driver has been removed,
as well as a failure to create the debugfs entries when they are added
again on driver probe.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The host1x_bo_pin() and host1x_bo_unpin() APIs are used to pin and unpin
buffers during host1x job submission. Pinning currently returns the SG
table and the DMA address (an IOVA if an IOMMU is used or a physical
address if no IOMMU is used) of the buffer. The DMA address is only used
for buffers that are relocated, whereas the host1x driver will map
gather buffers into its own IOVA space so that they can be processed by
the CDMA engine.
This approach has a couple of issues. On one hand it's not very useful
to return a DMA address for the buffer if host1x doesn't need it. On the
other hand, returning the SG table of the buffer is suboptimal because a
single SG table cannot be shared for multiple mappings, because the DMA
address is stored within the SG table, and the DMA address may be
different for different devices.
Subsequent patches will move the host1x driver over to the DMA API which
doesn't work with a single shared SG table. Fix this by returning a new
SG table each time a buffer is pinned. This allows the buffer to be
referenced by multiple jobs for different engines.
Change the prototypes of host1x_bo_pin() and host1x_bo_unpin() to take a
struct device *, specifying the device for which the buffer should be
pinned. This is required in order to be able to properly construct the
SG table. While at it, make host1x_bo_pin() return the SG table because
that allows us to return an ERR_PTR()-encoded error code if we need to,
or return NULL to signal that we don't need the SG table to be remapped
and can simply use the DMA address as-is. At the same time, returning
the DMA address is made optional because in the example of command
buffers, host1x doesn't need to know the DMA address since it will have
to create its own mapping anyway.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The host1x_cdma_wait_pushbuffer_space() function is not declared or
directly called from outside the file it is in, so make it static.
Fixes the following sparse warning:
drivers/gpu/host1x/cdma.c:235:5: warning: symbol 'host1x_cdma_wait_pushbuffer_space' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Thierry Reding <treding@nvidia.com>
A struct device doesn't carry much information that a channel might be
interested in, but the client very much does. Request channels for the
clients rather than their parent devices and store a pointer to them
in order to have that information available when needed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
It's technically not required to explicitly initialize the fields that
will be zero by default, but it's easier to read these structures if
they are all initialized uniformly.
Signed-off-by: Thierry Reding <treding@nvidia.com>
host1x nor any its clients have any limitations on the DMA segment size,
so don't pretend that they do.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This contains a couple of small improvements and cleanups for the Tegra
DRM driver.
-----BEGIN PGP SIGNATURE-----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=T2hU
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-5.3-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v5.3-rc1
This contains a couple of small improvements and cleanups for the Tegra
DRM driver.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thierry Reding <thierry.reding@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190621150753.19550-1-thierry.reding@gmail.com
So there is no need to check for a value that can never happen. No need
to check the return value all anyway, as any debugfs call can take the
result of this function as an option just fine.
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Based on 1 normalized pattern(s):
this software is licensed under the terms of the gnu general public
license version 2 as published by the free software foundation and
may be copied distributed and modified under those terms this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 285 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.642774971@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Logical devices created by the host1x bus infrastructure don't need to
be associated with a device tree node. Doing so will cause the driver
core to attempt to hook up IOMMU operations and fail because it is not
a real device.
However, for backwards-compatibility, we need to provide various OF_*
uevent variables that were previously provided by of_device_uevent() and
which are parsed by libdrm in userspace when querying the available
devices. Do this by implementing a uevent callback for the host1x bus.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Recent versions of the DMA API debug code have started to warn about
violations of the maximum DMA segment size. This is because the segment
size defaults to 64 KiB, which can easily be exceeded in large buffer
allocations such as used in DRM/KMS for framebuffers.
Technically the Tegra SMMU and ARM SMMU don't have a maximum segment
size (they map individual pages irrespective of whether they are
contiguous or not), so the choice of 4 MiB is a bit arbitrary here. The
maximum segment size is a 32-bit unsigned integer, though, so we can't
set it to the correct maximum size, which would be the size of the
aperture.
Signed-off-by: Thierry Reding <treding@nvidia.com>
When deferring probe, avoid logging a confusing error message. While at
it, make the error message more informational.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 228 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528171438.107155473@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If SMMU support is not available, fall back to programming the bypass
stream ID (0x7f).
Fixes: de5469c21f ("gpu: host1x: Program the channel stream ID")
Suggested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
[treding@nvidia.com: rebase this on top of a later build fix]
Signed-off-by: Thierry Reding <treding@nvidia.com>
In case the IOMMU API is not available compiling host1x fails with
the following error:
In file included from drivers/gpu/host1x/hw/host1x06.c:27:
drivers/gpu/host1x/hw/channel_hw.c: In function ‘host1x_channel_set_streamid’:
drivers/gpu/host1x/hw/channel_hw.c:118:30: error: implicit declaration of function
‘dev_iommu_fwspec_get’; did you mean ‘iommu_fwspec_free’? [-Werror=implicit-function-declaration]
struct iommu_fwspec *spec = dev_iommu_fwspec_get(channel->dev->parent);
^~~~~~~~~~~~~~~~~~~~
iommu_fwspec_free
Fixes: de5469c21f ("gpu: host1x: Program the channel stream ID")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Currently gathers of a hung job are getting NOP'ed and a restarted CDMA
executes the NOP'ed gathers. There shouldn't be a reason to not restart
CDMA execution starting with a next job, avoiding the unnecessary churning
with gathers NOP'ing.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
There is a chance that the last job has been completed at the time of
CDMA timeout handler invocation. In this case there is no need to complete
the completed job.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Host1x doesn't have information about jobs inter-dependency, that is
something that will become available once host1x will get a proper
jobs scheduler implementation. Currently a hang job causes other unrelated
jobs to be canceled, that is a relic from downstream driver which is
irrelevant to upstream. Let's cancel only the hanging job and not to touch
other jobs in queue.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The host1x CDMA push buffer is terminated by a special opcode (RESTART)
that tells the CDMA to wrap around to the beginning of the push buffer.
To accomodate the RESTART opcode, an extra 4 bytes are allocated on top
of the 512 * 8 = 4096 bytes needed for the 512 slots (1 slot = 2 words)
that are used for other commands passed to CDMA. This requires that two
memory pages are allocated, but most of the second page (4092 bytes) is
never used.
Decrease the number of slots to 511 so that the RESTART opcode fits
within the page. Adjust the push buffer wraparound code to take into
account push buffer sizes that are not a power of two.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The HOST1X_CHANNEL_DMAEND is an offset relative to the value written to
the HOST1X_CHANNEL_DMASTART register, but it is currently treated as an
absolute address. This can cause SMMU faults if the CDMA fetches past a
pushbuffer's IOMMU mapping.
Properly setting the DMAEND prevents the CDMA from fetching beyond that
address and avoid such issues. This is currently not observed because a
whole (almost) page of essentially scratch space absorbs any excessive
prefetching by CDMA. However, changing the number of slots in the push
buffer can trigger these SMMU faults.
Signed-off-by: Thierry Reding <treding@nvidia.com>
On Tegra186 and later, the ARM SMMU provides an input address space that
is 48 bits wide. However, memory clients can only address up to 40 bits.
If the geometry is used as-is, allocations of IOVA space can end up in a
region that is not addressable by the memory clients.
To fix this, restrict the IOVA space to the DMA mask of the host1x
device.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra186 and later support 40 bits of address space. Additional
registers need to be programmed to store the full 40 bits of push
buffer addresses.
Since command stream gathers can also reside in buffers in a 40-bit
address space, a new variant of the GATHER opcode is also introduced.
It takes two parameters: the first parameter contains the lower 32
bits of the address and the second parameter contains bits 32 to 39.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The CDMA push buffer can currently only handle opcodes that take a
single word parameter. However, the host1x implementation on Tegra186
and later supports opcodes that require multiple words as parameters.
Unfortunately the way the push buffer is structured, these wide opcodes
cannot simply be composed of two regular opcodes because that could
result in the wide opcode being split across the end of the push buffer
and the final RESTART opcode required to wrap the push buffer around
would break the wide opcode.
One way to fix this would be to remove the concept of slots to simplify
push buffer operations. However, that's not entirely trivial and should
be done in a separate patch. For now, simply use a different function
to push four-word opcodes into the push buffer. Technically only three
words are pushed, with the fourth word used as padding to preserve the
2-word alignment required by the slots abstraction. The fourth word is
always a NOP opcode.
Additional care must be taken when the end of the push buffer is
reached. If a four-word opcode doesn't fit into the push buffer without
being split by the boundary, NOP opcodes will be introduced and the new
wide opcode placed at the beginning of the push buffer.
Signed-off-by: Thierry Reding <treding@nvidia.com>
When processing command streams, make sure the host1x's stream ID is
programmed for the channel so that addresses are properly translated
through the SMMU.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In order to enable the MMIO path stream ID protection provided by the
incarnation of host1x found in Tegra186 and later, the host1x must be
provided with the list of stream ID register offsets for each of its
clients. Some clients (such as VIC) have multiple stream ID registers
that are assumed to be contiguous. The host1x is programmed with the
base offset and a limit which provide the range of registers that the
host1x needs to monitor for writes.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This new debugfs file represents the state of host1x bus devices,
specifying the list of subdevices and marking which ones have
successfully registered.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In this usage, the two are completely equivalent, but the completion
documents better what is going on, and we generally try to avoid
semaphores these days.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The host1x hardware found on Tegra194 is mostly backwards compatible
with the version found on Tegra186, with the notable exceptions of the
increased number of syncpoints and mlocks. In addition, some rarely
used features such as syncpoint wait bases were dropped and some
registers had to move around to accomodate the increased number of
syncpoints.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The number of syncpoints on Tegra186 is 576 and therefore no longer fits
into 8 bits. Increase the size of the syncpoint ID field to 10 in order
to accomodate all syncpoints.
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The register region allocated per channel was decreased from 16384 bytes
to 256 bytes on Tegra186 and later. Resize the region to make sure every
channel (instead of only the first) is properly programmed.
Suggested-by: Mikko Perttunen <mperttunen@nvidia.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Host1x is getting attached to an implicit IOMMU DMA domain if
CONFIG_ARM_DMA_USE_IOMMU=y. Since Host1x driver manages IOMMU by
itself, Host1x device must be detached from the implicit domain using
arch-specific IOMMU-API.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
All other assignments have a single space around the = sign, so remove
the spurious tab for consistency.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Only gather pins are mapped by the Host1x driver, regular BO relocations
are not. Check whether size of unpin isn't 0, otherwise IOVA allocation at
0x0 could be erroneously released.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Host1x's CDMA can't access the command buffers if IOMMU and Host1x
firewall are enabled in the kernels config because firewall doesn't map
the copied buffer into IOVA space. Fix this by skipping IOMMU
initialization if firewall is enabled as firewall merges sparse cmdbufs
into a single contiguous buffer and hence IOMMU isn't needed in this case.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
-----BEGIN PGP SIGNATURE-----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=twst
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2018-06-06-1' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"This starts to support NVIDIA volta hardware with nouveau, and adds
amdgpu support for the GPU in the Kabylake-G (the intel + radeon
single package chip), along with some initial Intel icelake enabling.
Summary:
New Drivers:
- v3d - driver for broadcom V3D V3.x+ hardware
- xen-front - XEN PV display frontend
core:
- handle zpos normalization in the core
- stop looking at legacy pointers in atomic paths
- improved scheduler documentation
- improved aspect ratio validation
- aspect ratio support for 64:27 and 256:135
- drop unused control node code.
i915:
- Icelake (ICL) enabling
- GuC/HuC refactoring
- PSR/PSR2 enabling and fixes
- DPLL management refactoring
- DP MST fixes
- NV12 enabling
- HDCP improvements
- GEM/Execlist/reset improvements
- GVT improvements
- stolen memory first 4k fix
amdgpu:
- Vega 20 support
- VEGAM support (Kabylake-G)
- preOS scanout buffer reservation
- power management gfxoff support for raven
- SR-IOV fixes
- Vega10 power profiles and clock voltage control
- scatter/gather display support on CZ/ST
amdkfd:
- GFX9 dGPU support
- userptr memory mapping
nouveau:
- major refactoring for Volta GV100 support
tda998x:
- HDMI i2c CEC support
etnaviv:
- removed unused logging code
- license text cleanups
- MMU handling improvements
- timeout fence fix for 50 days uptime
tegra:
- IOMMU support in gr2d/gr3d drivers
- zpos support
vc4:
- syncobj support
- CTM, plane alpha and async cursor support
analogix_dp:
- HPD and aux chan fixes
sun4i:
- MIPI DSI support
tilcdc:
- clock divider fixes for OMAP-l138 LCDK board
rcar-du:
- R8A77965 support
- dma-buf fences fixes
- hardware indexed crtc/du group handling
- generic zplane property support
atmel-hclcdc:
- generic zplane property support
mediatek:
- use generic video mode function
exynos:
- S5PV210 FIMD variant support
- IPP v2 framework
- more HW overlays support"
* tag 'drm-next-2018-06-06-1' of git://anongit.freedesktop.org/drm/drm: (1286 commits)
drm/amdgpu: fix 32-bit build warning
drm/exynos: fimc: signedness bug in fimc_setup_clocks()
drm/exynos: scaler: fix static checker warning
drm/amdgpu: Use dev_info() to report amdkfd is not supported for this ASIC
drm/amd/display: Remove use of division operator for long longs
drm/amdgpu: Update GFX info structure to match what vega20 used
drm/amdgpu/pp: remove duplicate assignment
drm/sched: add rcu_barrier after entity fini
drm/amdgpu: move VM BOs on LRU again
drm/amdgpu: consistenly use VM moved flag
drm/amdgpu: kmap PDs/PTs in amdgpu_vm_update_directories
drm/amdgpu: further optimize amdgpu_vm_handle_moved
drm/amdgpu: cleanup amdgpu_vm_validate_pt_bos v2
drm/amdgpu: rework VM state machine lock handling v2
drm/amdgpu: Add runtime VCN PG support
drm/amdgpu: Enable VCN static PG by default on RV
drm/amdgpu: Add VCN static PG support on RV
drm/amdgpu: Enable VCN CG by default on RV
drm/amdgpu: Add static CG control for VCN on RV
drm/exynos: Fix default value for zpos plane property
...
The number of words and the offset in a gather don't need to be
explicitly sized, so make them unsigned int instead.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Dmitry Osipenko