Underlying I2C bus drivers not always support longer transfers and
imx-lpi2c for instance doesn't. The fix is symmetric to previous patch
which fixed the read direction.
Cc: stable@vger.kernel.org # v5.20+
Fixes: bbc23a07b0 ("tpm: Add tpm_tis_i2c backend for tpm_tis_core")
Tested-by: Michael Haener <michael.haener@siemens.com>
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Underlying I2C bus drivers not always support longer transfers and
imx-lpi2c for instance doesn't. SLB 9673 offers 427-bytes packets.
Visible symptoms are:
tpm tpm0: Error left over data
tpm tpm0: tpm_transmit: tpm_recv: error -5
tpm_tis_i2c: probe of 1-002e failed with error -5
Cc: stable@vger.kernel.org # v5.20+
Fixes: bbc23a07b0 ("tpm: Add tpm_tis_i2c backend for tpm_tis_core")
Tested-by: Michael Haener <michael.haener@siemens.com>
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
The failure paths in tpm_tis_spi_transfer() do not deactivate
chip select. Send an empty message (cs_select == 0) to overcome
this.
The patch is tested by two ways.
One way needs to touch hardware:
1. force pull MISO pin down to GND, it emulates a forever
'WAIT' timing.
2. probe cs pin by an oscilloscope.
3. load tpm_tis_spi.ko.
After loading, dmesg prints:
"probe of spi0.0 failed with error -110"
and oscilloscope shows cs pin goes high(deactivated) after
the failure. Before the patch, cs pin keeps low.
Second way is by writing a fake spi controller.
1. implement .transfer_one method, fill all rx buf with 0.
2. implement .set_cs method, print the state of cs pin.
we can see cs goes high after the failure.
Signed-off-by: Peijie Shao <shaopeijie@cestc.cn>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
/dev/vtpmx is made visible before 'workqueue' is initialized, which can
lead to a memory corruption in the worst case scenario.
Address this by initializing 'workqueue' as the very first step of the
driver initialization.
Cc: stable@vger.kernel.org
Fixes: 6f99612e25 ("tpm: Proxy driver for supporting multiple emulated TPMs")
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@tuni.fi>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
As kcs_bmc_handle_event() is executed inside both a timer and a hardirq,
it should disable irq before lock acquisition otherwise deadlock could
happen if the timmer is preemtped by the irq.
Possible deadlock scenario:
aspeed_kcs_check_obe() (timer)
-> kcs_bmc_handle_event()
-> spin_lock(&kcs_bmc->lock)
<irq interruption>
-> aspeed_kcs_irq()
-> kcs_bmc_handle_event()
-> spin_lock(&kcs_bmc->lock) (deadlock here)
This flaw was found using an experimental static analysis tool we are
developing for irq-related deadlock.
The tentative patch fix the potential deadlock by spin_lock_irqsave()
Signed-off-by: Chengfeng Ye <dg573847474@gmail.com>
Message-Id: <20230627152449.36093-1-dg573847474@gmail.com>
Signed-off-by: Corey Minyard <minyard@acm.org>
resume support in vdpa/solidrun
structure size optimizations in virtio_pci
new pds_vdpa driver
immediate initialization mechanism for vdpa/ifcvf
interrupt bypass for vdpa/mlx5
multiple worker support for vhost
viirtio net in Intel F2000X-PL support for vdpa/ifcvf
fixes, cleanups all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmSi95cPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpJ58H/A++mwjLsoiJ/3xgf2S2Fn0p0lkgxg61LrjD
Q9p8zstG/BndRvv018XcJKoklaHpb4WcmNctKRNZJ6BjPj+ZwdADuSzoaUNurPD4
M3s/nXVWvg7/2FifGDpCzQpyw0MR0Ip6/yqtdTl4vuLZGxI1nNGDfYbDgc3vZeCp
pYTLsl/XUPzix4iJouEQqy5rmlUia3IE751aECrdk58z17lDo/Znar4hsXF0acQY
+G6C/MNZQgf1rtJIl901h54W8rAoubxeda80uXSQk9fDyPG/wZYh2wFBGPi9qYa+
9E+tOgHprMZ7G5GEopDdd19UctuW7M+YXPWZa1ijp8EZXmMpzuo=
=5tdF
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio updates from Michael Tsirkin:
- resume support in vdpa/solidrun
- structure size optimizations in virtio_pci
- new pds_vdpa driver
- immediate initialization mechanism for vdpa/ifcvf
- interrupt bypass for vdpa/mlx5
- multiple worker support for vhost
- viirtio net in Intel F2000X-PL support for vdpa/ifcvf
- fixes, cleanups all over the place
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (48 commits)
vhost: Make parameter name match of vhost_get_vq_desc()
vduse: fix NULL pointer dereference
vhost: Allow worker switching while work is queueing
vhost_scsi: add support for worker ioctls
vhost: allow userspace to create workers
vhost: replace single worker pointer with xarray
vhost: add helper to parse userspace vring state/file
vhost: remove vhost_work_queue
vhost_scsi: flush IO vqs then send TMF rsp
vhost_scsi: convert to vhost_vq_work_queue
vhost_scsi: make SCSI cmd completion per vq
vhost_sock: convert to vhost_vq_work_queue
vhost: convert poll work to be vq based
vhost: take worker or vq for flushing
vhost: take worker or vq instead of dev for queueing
vhost, vhost_net: add helper to check if vq has work
vhost: add vhost_worker pointer to vhost_virtqueue
vhost: dynamically allocate vhost_worker
vhost: create worker at end of vhost_dev_set_owner
virtio_bt: call scheduler when we free unused buffs
...
Here is the big set of char/misc and other driver subsystem updates for
6.5-rc1.
Lots of different, tiny, stuff in here, from a range of smaller driver
subsystems, including pulls from some substems directly:
- IIO driver updates and additions
- W1 driver updates and fixes (and a new maintainer!)
- FPGA driver updates and fixes
- Counter driver updates
- Extcon driver updates
- Interconnect driver updates
- Coresight driver updates
- mfd tree tag merge needed for other updates
on top of that, lots of small driver updates as patches, including:
- static const updates for class structures
- nvmem driver updates
- pcmcia driver fix
- lots of other small driver updates and fixes
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZKKNMw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylhlQCfZrtz8RIbau8zbzh/CKpKBOmvHp4An3V64hbz
recBPLH0ZACKl0wPl4iZ
=A83A
-----END PGP SIGNATURE-----
Merge tag 'char-misc-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull Char/Misc updates from Greg KH:
"Here is the big set of char/misc and other driver subsystem updates
for 6.5-rc1.
Lots of different, tiny, stuff in here, from a range of smaller driver
subsystems, including pulls from some substems directly:
- IIO driver updates and additions
- W1 driver updates and fixes (and a new maintainer!)
- FPGA driver updates and fixes
- Counter driver updates
- Extcon driver updates
- Interconnect driver updates
- Coresight driver updates
- mfd tree tag merge needed for other updates on top of that, lots of
small driver updates as patches, including:
- static const updates for class structures
- nvmem driver updates
- pcmcia driver fix
- lots of other small driver updates and fixes
All of these have been in linux-next for a while with no reported
problems"
* tag 'char-misc-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (243 commits)
bsr: fix build problem with bsr_class static cleanup
comedi: make all 'class' structures const
char: xillybus: make xillybus_class a static const structure
xilinx_hwicap: make icap_class a static const structure
virtio_console: make port class a static const structure
ppdev: make ppdev_class a static const structure
char: misc: make misc_class a static const structure
/dev/mem: make mem_class a static const structure
char: lp: make lp_class a static const structure
dsp56k: make dsp56k_class a static const structure
bsr: make bsr_class a static const structure
oradax: make 'cl' a static const structure
hwtracing: hisi_ptt: Fix potential sleep in atomic context
hwtracing: hisi_ptt: Advertise PERF_PMU_CAP_NO_EXCLUDE for PTT PMU
hwtracing: hisi_ptt: Export available filters through sysfs
hwtracing: hisi_ptt: Add support for dynamically updating the filter list
hwtracing: hisi_ptt: Factor out filter allocation and release operation
samples: pfsm: add CC_CAN_LINK dependency
misc: fastrpc: check return value of devm_kasprintf()
coresight: dummy: Update type of mode parameter in dummy_{sink,source}_enable()
...
For virtio-net we were getting CPU stall warnings, and fixed it by
calling the scheduler: see f8bb510439 ("virtio_net: suppress cpu stall
when free_unused_bufs").
This driver is similar so theoretically the same logic applies.
Signed-off-by: Xianting Tian <xianting.tian@linux.alibaba.com>
Message-Id: <20230609131817.712867-3-xianting.tian@linux.alibaba.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
API:
- Add linear akcipher/sig API.
- Add tfm cloning (hmac, cmac).
- Add statesize to crypto_ahash.
Algorithms:
- Allow only odd e and restrict value in FIPS mode for RSA.
- Replace LFSR with SHA3-256 in jitter.
- Add interface for gathering of raw entropy in jitter.
Drivers:
- Fix race on data_avail and actual data in hwrng/virtio.
- Add hash and HMAC support in starfive.
- Add RSA algo support in starfive.
- Add support for PCI device 0x156E in ccp.
-----BEGIN PGP SIGNATURE-----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=rOLu
-----END PGP SIGNATURE-----
Merge tag 'v6.5-p1' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto updates from Herbert Xu:
"API:
- Add linear akcipher/sig API
- Add tfm cloning (hmac, cmac)
- Add statesize to crypto_ahash
Algorithms:
- Allow only odd e and restrict value in FIPS mode for RSA
- Replace LFSR with SHA3-256 in jitter
- Add interface for gathering of raw entropy in jitter
Drivers:
- Fix race on data_avail and actual data in hwrng/virtio
- Add hash and HMAC support in starfive
- Add RSA algo support in starfive
- Add support for PCI device 0x156E in ccp"
* tag 'v6.5-p1' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (85 commits)
crypto: akcipher - Do not copy dst if it is NULL
crypto: sig - Fix verify call
crypto: akcipher - Set request tfm on sync path
crypto: sm2 - Provide sm2_compute_z_digest when sm2 is disabled
hwrng: imx-rngc - switch to DEFINE_SIMPLE_DEV_PM_OPS
hwrng: st - keep clock enabled while hwrng is registered
hwrng: st - support compile-testing
hwrng: imx-rngc - fix the timeout for init and self check
KEYS: asymmetric: Use new crypto interface without scatterlists
KEYS: asymmetric: Move sm2 code into x509_public_key
KEYS: Add forward declaration in asymmetric-parser.h
crypto: sig - Add interface for sign/verify
crypto: akcipher - Add sync interface without SG lists
crypto: cipher - On clone do crypto_mod_get()
crypto: api - Add __crypto_alloc_tfmgfp
crypto: api - Remove crypto_init_ops()
crypto: rsa - allow only odd e and restrict value in FIPS mode
crypto: geniv - Split geniv out of AEAD Kconfig option
crypto: algboss - Add missing dependency on RNG2
crypto: starfive - Add RSA algo support
...
- added support for Wifi/Bluetooth on CI20
- reworked Ralink clock and reset handling
- cleanups and fixes
-----BEGIN PGP SIGNATURE-----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=z9/q
-----END PGP SIGNATURE-----
Merge tag 'mips_6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Thomas Bogendoerfer:
- add support for TP-Link HC220 G5 v1
- add support for Wifi/Bluetooth on CI20
- rework Ralink clock and reset handling
- cleanups and fixes
* tag 'mips_6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (58 commits)
MIPS: Loongson64: DTS: Add RTC support to Loongson-2K1000
MIPS: Loongson64: DTS: Add RTC support to LS7A PCH
MIPS: OCTEON: octeon-usb: cleanup divider calculation
MIPS: OCTEON: octeon-usb: introduce dwc3_octeon_{read,write}q
MIPS: OCTEON: octeon-usb: move gpio config to separate function
MIPS: OCTEON: octeon-usb: use bitfields for shim register
MIPS: OCTEON: octeon-usb: use bitfields for host config register
MIPS: OCTEON: octeon-usb: use bitfields for control register
MIPS: OCTEON: octeon-usb: add all register offsets
mips: ralink: match all supported system controller compatible strings
MIPS: dec: prom: Address -Warray-bounds warning
MIPS: DTS: CI20: Raise VDDCORE voltage to 1.125 volts
clk: ralink: mtmips: Fix uninitialized use of ret in mtmips_register_{fixed,factor}_clocks()
mips: ralink: introduce commonly used remap node function
mips: pci-mt7620: use dev_info() to log PCIe device detection result
mips: pci-mt7620: do not print NFTS register value as error log
MAINTAINERS: add Mediatek MTMIPS Clock maintainer
mips: ralink: get cpu rate from new driver code
mips: ralink: remove reset related code
mips: ralink: mt7620: remove clock related code
...
Kmemleak reported the following leak info in try_smi_init():
unreferenced object 0xffff00018ecf9400 (size 1024):
comm "modprobe", pid 2707763, jiffies 4300851415 (age 773.308s)
backtrace:
[<000000004ca5b312>] __kmalloc+0x4b8/0x7b0
[<00000000953b1072>] try_smi_init+0x148/0x5dc [ipmi_si]
[<000000006460d325>] 0xffff800081b10148
[<0000000039206ea5>] do_one_initcall+0x64/0x2a4
[<00000000601399ce>] do_init_module+0x50/0x300
[<000000003c12ba3c>] load_module+0x7a8/0x9e0
[<00000000c246fffe>] __se_sys_init_module+0x104/0x180
[<00000000eea99093>] __arm64_sys_init_module+0x24/0x30
[<0000000021b1ef87>] el0_svc_common.constprop.0+0x94/0x250
[<0000000070f4f8b7>] do_el0_svc+0x48/0xe0
[<000000005a05337f>] el0_svc+0x24/0x3c
[<000000005eb248d6>] el0_sync_handler+0x160/0x164
[<0000000030a59039>] el0_sync+0x160/0x180
The problem was that when an error occurred before handlers registration
and after allocating `new_smi->si_sm`, the variable wouldn't be freed in
the error handling afterwards since `shutdown_smi()` hadn't been
registered yet. Fix it by adding a `kfree()` in the error handling path
in `try_smi_init()`.
Cc: stable@vger.kernel.org # 4.19+
Fixes: 7960f18a56 ("ipmi_si: Convert over to a shutdown handler")
Signed-off-by: Yi Yang <yiyang13@huawei.com>
Co-developed-by: GONG, Ruiqi <gongruiqi@huaweicloud.com>
Signed-off-by: GONG, Ruiqi <gongruiqi@huaweicloud.com>
Message-Id: <20230629123328.2402075-1-gongruiqi@huaweicloud.com>
Signed-off-by: Corey Minyard <minyard@acm.org>
-----BEGIN PGP SIGNATURE-----
iQJEBAABCAAuFiEEwPw5LcreJtl1+l5K99NY+ylx4KYFAmSV8QgQHGF4Ym9lQGtl
cm5lbC5kawAKCRD301j7KXHgpupIEADKEZvpxDyaxHjYZFFeoSJRkh+AEJHe0Xtr
J5vUL8t8zmAV3F7i8XaoAEcR0dC0VQcoTc8fAOty71+5hsc7gvtyyNjqU/YWRVqK
Xr+VJuSJ+OGx3MzpRWEkepagfPyqP5cyyCOK6gqIgqzc3IwqkR/3QHVRc6oR8YbY
AQd7tqm2fQXK9WDHEy5hcaQeqb9uKZjQQoZejpPPerpJM+9RMgKxpCGtnLLIUhr/
sgl7KyLIQPBmveO2vfOR+dmsJBqsLqneqkXDKMAIfpeVEEkHHAlCH4E5Ne1XUS+s
ie4If+reuyn1Ktt5Ry1t7w2wr8cX1fcay3K28tgwjE2Bvremc5YnYgb3pyUDW38f
tXXkpg/eTXd/Pn0Crpagoa9zJ927tt5JXIO1/PagPEP1XOqUuthshDFsrVqfqbs+
36gqX2JWB4NJTg9B9KBHA3+iVCJyZLjUqOqws7hOJOvhQytZVm/IwkGBg1Slhe1a
J5WemBlqX8lTgXz0nM7cOhPYTZeKe6hazCcb5VwxTUTj9SGyYtsMfqqTwRJO9kiF
j1VzbOAgExDYe+GvfqOFPh9VqZho66+DyOD/Xtca4eH7oYyHSmP66o8nhRyPBPZA
maBxQhUkPQn4/V/0fL2TwIdWYKsbj8bUyINKPZ2L35YfeICiaYIctTwNJxtRmItB
M3VxWD3GZQ==
=KhW4
-----END PGP SIGNATURE-----
Merge tag 'for-6.5/splice-2023-06-23' of git://git.kernel.dk/linux
Pull splice updates from Jens Axboe:
"This kills off ITER_PIPE to avoid a race between truncate,
iov_iter_revert() on the pipe and an as-yet incomplete DMA to a bio
with unpinned/unref'ed pages from an O_DIRECT splice read. This causes
memory corruption.
Instead, we either use (a) filemap_splice_read(), which invokes the
buffered file reading code and splices from the pagecache into the
pipe; (b) copy_splice_read(), which bulk-allocates a buffer, reads
into it and then pushes the filled pages into the pipe; or (c) handle
it in filesystem-specific code.
Summary:
- Rename direct_splice_read() to copy_splice_read()
- Simplify the calculations for the number of pages to be reclaimed
in copy_splice_read()
- Turn do_splice_to() into a helper, vfs_splice_read(), so that it
can be used by overlayfs and coda to perform the checks on the
lower fs
- Make vfs_splice_read() jump to copy_splice_read() to handle
direct-I/O and DAX
- Provide shmem with its own splice_read to handle non-existent pages
in the pagecache. We don't want a ->read_folio() as we don't want
to populate holes, but filemap_get_pages() requires it
- Provide overlayfs with its own splice_read to call down to a lower
layer as overlayfs doesn't provide ->read_folio()
- Provide coda with its own splice_read to call down to a lower layer
as coda doesn't provide ->read_folio()
- Direct ->splice_read to copy_splice_read() in tty, procfs, kernfs
and random files as they just copy to the output buffer and don't
splice pages
- Provide wrappers for afs, ceph, ecryptfs, ext4, f2fs, nfs, ntfs3,
ocfs2, orangefs, xfs and zonefs to do locking and/or revalidation
- Make cifs use filemap_splice_read()
- Replace pointers to generic_file_splice_read() with pointers to
filemap_splice_read() as DIO and DAX are handled in the caller;
filesystems can still provide their own alternate ->splice_read()
op
- Remove generic_file_splice_read()
- Remove ITER_PIPE and its paraphernalia as generic_file_splice_read
was the only user"
* tag 'for-6.5/splice-2023-06-23' of git://git.kernel.dk/linux: (31 commits)
splice: kdoc for filemap_splice_read() and copy_splice_read()
iov_iter: Kill ITER_PIPE
splice: Remove generic_file_splice_read()
splice: Use filemap_splice_read() instead of generic_file_splice_read()
cifs: Use filemap_splice_read()
trace: Convert trace/seq to use copy_splice_read()
zonefs: Provide a splice-read wrapper
xfs: Provide a splice-read wrapper
orangefs: Provide a splice-read wrapper
ocfs2: Provide a splice-read wrapper
ntfs3: Provide a splice-read wrapper
nfs: Provide a splice-read wrapper
f2fs: Provide a splice-read wrapper
ext4: Provide a splice-read wrapper
ecryptfs: Provide a splice-read wrapper
ceph: Provide a splice-read wrapper
afs: Provide a splice-read wrapper
9p: Add splice_read wrapper
net: Make sock_splice_read() use copy_splice_read() by default
tty, proc, kernfs, random: Use copy_splice_read()
...
In commit e55ce9fd3d ("bsr: make bsr_class a static const structure"),
the bsr_init function was converted to handle a static class structure,
but the conversion got a variable name wrong, which caused build errors
so fix that up.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Ivan Orlov <ivan.orlov0322@gmail.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://lore.kernel.org/r/20230626142537.755ec782@canb.auug.org.au
Fixes: e55ce9fd3d ("bsr: make bsr_class a static const structure")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the driver core allows for struct class to be in read-only
memory, move the xillybus_class structure to be declared at build time
placing it into read-only memory, instead of having to be dynamically
allocated at load time.
Cc: Eli Billauer <eli.billauer@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ivan Orlov <ivan.orlov0322@gmail.com>
Acked-by: Eli Billauer <eli.billauer@gmail.com>
Link: https://lore.kernel.org/r/20230620143751.578239-18-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the driver core allows for struct class to be in read-only
memory, move the icap_class structure to be declared at build time
placing it into read-only memory, instead of having to be dynamically
allocated at load time.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Michal Simek <michal.simek@amd.com>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: Ivan Orlov <ivan.orlov0322@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ivan Orlov <ivan.orlov0322@gmail.com>
Link: https://lore.kernel.org/r/20230620143751.578239-17-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the driver core allows for struct class to be in read-only
memory, remove the class field of the ports_driver_data structure and
create the port_class static class structure declared at build time
which places it into read-only memory, instead of having it to be
dynamically allocated at load time.
Cc: Amit Shah <amit@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: virtualization@lists.linux-foundation.org
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ivan Orlov <ivan.orlov0322@gmail.com>
Link: https://lore.kernel.org/r/20230620143751.578239-16-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the driver core allows for struct class to be in read-only
memory, move the ppdev_class structure to be declared at build time
placing it into read-only memory, instead of having to be dynamically
allocated at load time.
Cc: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ivan Orlov <ivan.orlov0322@gmail.com>
Link: https://lore.kernel.org/r/20230620143751.578239-15-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the driver core allows for struct class to be in read-only
memory, move the misc_class structure to be declared at build time
placing it into read-only memory, instead of having to be dynamically
allocated at load time.
Cc: Arnd Bergmann <arnd@arndb.de>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ivan Orlov <ivan.orlov0322@gmail.com>
Link: https://lore.kernel.org/r/20230620143751.578239-14-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the driver core allows for struct class to be in read-only
memory, move the mem_class structure to be declared at build time
placing it into read-only memory, instead of having to be dynamically
allocated at load time.
Cc: Arnd Bergmann <arnd@arndb.de>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ivan Orlov <ivan.orlov0322@gmail.com>
Link: https://lore.kernel.org/r/20230620143751.578239-13-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the driver core allows for struct class to be in read-only
memory, move the lp_class structure to be declared at build time
placing it into read-only memory, instead of having to be dynamically
allocated at load time.
Cc: Arnd Bergmann <arnd@arndb.de>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ivan Orlov <ivan.orlov0322@gmail.com>
Link: https://lore.kernel.org/r/20230620143751.578239-12-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the driver core allows for struct class to be in read-only
memory, move the dsp56k_class structure to be declared at build time
placing it into read-only memory, instead of having to be dynamically
allocated at boot time.
Cc: Arnd Bergmann <arnd@arndb.de>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ivan Orlov <ivan.orlov0322@gmail.com>
Link: https://lore.kernel.org/r/20230620143751.578239-11-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the driver core allows for struct class to be in read-only
memory, move the bsr_class structure to be declared at build time
placing it into read-only memory, instead of having to be dynamically
allocated at boot time.
Cc: Arnd Bergmann <arnd@arndb.de>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ivan Orlov <ivan.orlov0322@gmail.com>
Link: https://lore.kernel.org/r/20230620143751.578239-10-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SIMPLE_DEV_PM_OPS is deprecated, replace it with DEFINE_SIMPLE_DEV_PM_OPS
and use pm_sleep_ptr for setting the driver's pm routines. We can now
remove the __maybe_unused qualifier in the suspend and resume functions.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The st-rng driver uses devres to register itself with the hwrng core,
the driver will be unregistered from hwrng when its device goes out of
scope. This happens after the driver's remove function is called.
However, st-rng's clock is disabled in the remove function. There's a
short timeframe where st-rng is still registered with the hwrng core
although its clock is disabled. I suppose the clock must be active to
access the hardware and serve requests from the hwrng core.
Switch to devm_clk_get_enabled and let devres disable the clock and
unregister the hwrng. This avoids the race condition.
Fixes: 3e75241be8 ("hwrng: drivers - Use device-managed registration API")
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Allow compile-testing the st-rng driver if we're not running on an ST
chipset.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Fix the timeout that is used for the initialisation and for the self
test. wait_for_completion_timeout expects a timeout in jiffies, but
RNGC_TIMEOUT is in milliseconds. Call msecs_to_jiffies to do the
conversion.
Cc: stable@vger.kernel.org
Fixes: 1d5449445b ("hwrng: mx-rngc - add a driver for Freescale RNGC")
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When probing for an ACPI-specified IPMI device, the code would request
that the acpi_ipmi module be loaded ACPI operations through IPMI can be
performed. This could happen through module load context, for instance,
if an I2C module is loaded that caused the IPMI interface to be probed.
This is not allowed because a synchronous module load in this context
can result in an deadlock, and I was getting a warning:
[ 23.967853] WARNING: CPU: 0 PID: 21 at kernel/module/kmod.c:144 __request_module+0x1de/0x2d0
[ 23.968852] Modules linked in: i2c_i801 ipmi_ssif
The IPMI driver is not dependent on acpi_ipmi, so just change the called
to request_module_nowait to make the load asynchronous.
Signed-off-by: Corey Minyard <minyard@acm.org>
Now that the driver core allows for struct class to be in read-only
memory, move the ipmi_class structure to be declared at build time
placing it into read-only memory, instead of having to be dynamically
allocated at boot time.
Cc: Corey Minyard <minyard@acm.org>
Cc: openipmi-developer@lists.sourceforge.net
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ivan Orlov <ivan.orlov0322@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Message-Id: <20230620143701.577657-2-gregkh@linuxfoundation.org>
Signed-off-by: Corey Minyard <minyard@acm.org>
The adapter scan ssif_info_find() sets info->adapter_name if the adapter
info came from SMBIOS, as it's not set in that case. However, this
function can be called more than once, and it will leak the adapter name
if it had already been set. So check for NULL before setting it.
Fixes: c4436c9149 ("ipmi_ssif: avoid registering duplicate ssif interface")
Signed-off-by: Corey Minyard <minyard@acm.org>
Add check for the return value of kstrdup() and return the error
if it fails in order to avoid NULL pointer dereference.
Fixes: c4436c9149 ("ipmi_ssif: avoid registering duplicate ssif interface")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Message-Id: <20230619092802.35384-1-jiasheng@iscas.ac.cn>
Signed-off-by: Corey Minyard <minyard@acm.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Michal Simek <michal.simek@amd.com>
Message-ID: <20230605092047.50472-3-u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
hwicap_drv_remove() is only called for a device after hwicap_drv_probe()
returned 0. In that case dev_set_drvdata() was called (by hwicap_setup())
with a non-NULL value and so dev_get_drvdata() won't return NULL.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Michal Simek <michal.simek@amd.com>
Message-ID: <20230605092047.50472-2-u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
hwicap_remove() is only called by hwicap_drv_remove(). Simplify by
unrolling the former into the latter function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Michal Simek <michal.simek@amd.com>
Message-ID: <20230605092047.50472-1-u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The unxlate_dev_mem_ptr() function has no prototype on the mips
architecture, which does not include asm-generic/io.h, so gcc warns
about the __weak definition:
drivers/char/mem.c:94:29: error: no previous prototype for 'unxlate_dev_mem_ptr' [-Werror=missing-prototypes]
Since everyone else already gets the generic definition or has a custom
one, there is not really much point in having a __weak version as well.
Remove this one, and instead add a trivial macro to the mips header.
Once we convert mips to use the asm-generic header, this can go away
again.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
With commit 858e8b792d ("tpm, tpm_tis: Avoid cache incoherency in test
for interrupts") bit accessor functions are used to access flags in
tpm_tis_data->flags.
However these functions expect bit numbers, while the flags are defined
as bit masks in enum tpm_tis_flag.
Fix this inconsistency by using numbers instead of masks also for the
flags in the enum.
Reported-by: Pavel Machek <pavel@denx.de>
Fixes: 858e8b792d ("tpm, tpm_tis: Avoid cache incoherency in test for interrupts")
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Cc: stable@vger.kernel.org
Reviewed-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The way random data is read from hardware has changed from
Octeon CN10KA-B0 and later SoCs onwards. A new set of registers
have been added to read random data and to verify whether the
read data is valid or not. This patch extends and uses
RNM_PF_TRNG_DAT and RNM_PF_TRNG_STS CSRs to read random number
and status for the applicable silicon variants.
Signed-off-by: Bharat Bhushan <bbhushan2@marvell.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In a future patch HAS_IOPORT=n will result in inb()/outb() and friends
not being declared. We thus need to add HAS_IOPORT as dependency for
those drivers using them.
Co-developed-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Link: https://lore.kernel.org/r/20230522105049.1467313-4-schnelle@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Fix flush_dcache_page() for usage from irq context
- Handle kprobes breakpoints only in kernel context
- Handle kgdb breakpoints only in kernel context
- Use num_present_cpus() in alternative patching code
- Enable LOCKDEP support
- Add lightweight spinlock checks
- Flush AGP gatt writes and adjust gatt mask in parisc_agp_mask_memory()
- Allow to reboot machine after system halt
- Improve cache flushing for PCXL in arch_sync_dma_for_cpu()
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQS86RI+GtKfB8BJu973ErUQojoPXwUCZG/QkgAKCRD3ErUQojoP
X9MBAQCe2rJxNPmdUVZ8okvKTE/qukbJxa+pSlYm/+w5s4Q6nAD/TCBM5Meil0Q2
IOYAadCt4qaZfCOcIHBOgRqrnLXUbQQ=
=e2J6
-----END PGP SIGNATURE-----
Merge tag 'parisc-for-6.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc architecture fixes from Helge Deller:
"Quite a bunch of real bugfixes in here and most of them are tagged for
backporting: A fix for cache flushing from irq context, a kprobes &
kgdb breakpoint handling fix, and a fix in the alternative code
patching function to take care of CPU hotplugging.
parisc now provides LOCKDEP support and comes with a lightweight
spinlock check. Both features helped me to find the cache flush bug.
Additionally writing the AGP gatt has been fixed, the machine allows
the user to reboot after a system halt and arch_sync_dma_for_cpu() has
been optimized for PCXL PCUs.
Summary:
- Fix flush_dcache_page() for usage from irq context
- Handle kprobes breakpoints only in kernel context
- Handle kgdb breakpoints only in kernel context
- Use num_present_cpus() in alternative patching code
- Enable LOCKDEP support
- Add lightweight spinlock checks
- Flush AGP gatt writes and adjust gatt mask in parisc_agp_mask_memory()
- Allow to reboot machine after system halt
- Improve cache flushing for PCXL in arch_sync_dma_for_cpu()"
* tag 'parisc-for-6.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Fix flush_dcache_page() for usage from irq context
parisc: Handle kgdb breakpoints only in kernel context
parisc: Handle kprobes breakpoints only in kernel context
parisc: Allow to reboot machine after system halt
parisc: Enable LOCKDEP support
parisc: Add lightweight spinlock checks
parisc: Use num_present_cpus() in alternative patching code
parisc: Flush gatt writes and adjust gatt mask in parisc_agp_mask_memory()
parisc: Improve cache flushing for PCXL in arch_sync_dma_for_cpu()
After commit b8a1a4cd5a ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
03c835f498 ("i2c: Switch .probe() to not take an id parameter") convert
back to (the new) .probe() to be able to eventually drop .probe_new() from
struct i2c_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Message-Id: <20230525204021.696858-1-u.kleine-koenig@pengutronix.de>
Signed-off-by: Corey Minyard <minyard@acm.org>
Use copy_splice_read() for tty, procfs, kernfs and random files rather
than going through generic_file_splice_read() as they just copy the file
into the output buffer and don't splice pages. This avoids the need for
them to have a ->read_folio() to satisfy filemap_splice_read().
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cc: Christoph Hellwig <hch@lst.de>
cc: Jens Axboe <axboe@kernel.dk>
cc: Al Viro <viro@zeniv.linux.org.uk>
cc: John Hubbard <jhubbard@nvidia.com>
cc: David Hildenbrand <david@redhat.com>
cc: Matthew Wilcox <willy@infradead.org>
cc: Miklos Szeredi <miklos@szeredi.hu>
cc: Arnd Bergmann <arnd@arndb.de>
cc: linux-block@vger.kernel.org
cc: linux-fsdevel@vger.kernel.org
cc: linux-mm@kvack.org
Link: https://lore.kernel.org/r/20230522135018.2742245-13-dhowells@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We have no device-specific data for fsl,imx25-rngb. There's no need to
set .data = NULL, this is the default.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Mark the imx_rngc_probe function as __init.
There's no need to support hotplugging in the imx-rngc driver. We use
module_platform_driver_probe, the probe function will only be called at
startup.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Rewrite the defines for register bits to use BIT(x) instead of writing
out the 32-bit number. This makes it easier to compare the code with the
register descriptions in the reference manual.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use the mechanism from bitfield.h to read the rng type field in the
version_id register. This makes the code a tiny bit simpler.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The "level" field in the status register contains the number of random
bytes that are available in the FIFO. Use GENMASK to extract this field.
We only want to check if level is 0 or if we can read another byte.
There's no need for the shift or the level variable.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Interrupts got recently enabled for tpm_tis.
The interrupts initially works on the device but they will stop arriving
after circa ~200 interrupts. On system reboot/shutdown this will cause a
long wait (120000 jiffies).
[jarkko@kernel.org: fix a merge conflict and adjust the commit message]
Fixes: e644b2f498 ("tpm, tpm_tis: Enable interrupt test")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Read syscall cannot response to sigals when data_to_read remains at 0
and the while loop cannot break. Check signal_pending in the loop.
Reported-by: Zhen Ni <zhen.ni@easystack.cn>
Message-Id: <20230517085412.367022-1-zhen.ni@easystack.cn>
Signed-off-by: Corey Minyard <minyard@acm.org>
The P360 Tiny suffers from an irq storm issue like the T490s, so add
an entry for it to tpm_tis_dmi_table, and force polling. There also
previously was a report from the previous attempt to enable interrupts
that involved a ThinkPad L490. So an entry is added for it as well.
Cc: stable@vger.kernel.org
Reported-by: Peter Zijlstra <peterz@infradead.org> # P360 Tiny
Closes: https://lore.kernel.org/linux-integrity/20230505130731.GO83892@hirez.programming.kicks-ass.net/
Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Set TPM_CHIP_FLAG_SUSPENDED in tpm_pm_suspend() and reset in
tpm_pm_resume(). While the flag is set, tpm_hwrng() gives back zero
bytes. This prevents hwrng from racing during resume.
Cc: stable@vger.kernel.org
Fixes: 6e592a065d ("tpm: Move Linux RNG connection to hwrng")
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Before sending a TPM command, CLKRUN protocol must be disabled. This is not
done in the case of tpm1_do_selftest() call site inside tpm_tis_resume().
Address this by decorating the calls with tpm_chip_{start,stop}, which
should be always used to arm and disarm the TPM chip for transmission.
Finally, move the call to the main TPM driver callback as the last step
because it should arm the chip by itself, if it needs that type of
functionality.
Cc: stable@vger.kernel.org
Reported-by: Jason A. Donenfeld <Jason@zx2c4.com>
Closes: https://lore.kernel.org/linux-integrity/CS68AWILHXS4.3M36M1EKZLUMS@suppilovahvero/
Fixes: a3fbfae82b ("tpm: take TPM chip power gating out of tpm_transmit()")
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
The virtio rng device kicks off a new entropy request whenever the
data available reaches zero. When a new request occurs at the end
of a read operation, that is, when the result of that request is
only needed by the next reader, then there is a race between the
writing of the new data and the next reader.
This is because there is no synchronisation whatsoever between the
writer and the reader.
Fix this by writing data_avail with smp_store_release and reading
it with smp_load_acquire when we first enter read. The subsequent
reads are safe because they're either protected by the first load
acquire, or by the completion mechanism.
Also remove the redundant zeroing of data_idx in random_recv_done
(data_idx must already be zero at this point) and data_avail in
request_entropy (ditto).
Reported-by: syzbot+726dc8c62c3536431ceb@syzkaller.appspotmail.com
Fixes: f7f510ec19 ("virtio: An entropy device, as suggested by hpa.")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Move to drivers/char/hw_random since histb-(t)rng does not provide
cryptography pseudo rng.
histb-rng is pretty like hisi-rng, but after investigation, we confirm
there is no RNG_PHY_SEED register on histb-rng so a separate driver is
needed.
Still we rename relevant function names to match those in hisi-rng.
Link: https://lore.kernel.org/r/20230401164448.1393336-1-mmyangfl@gmail.com
Signed-off-by: David Yang <mmyangfl@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add missing dependencies on HAS_IOMEM as otherwise they will trigger
failed builds with COMPILE_TEST enabled.
Also add dependencies on OF where appropriate.
Change the default so that these drivers are not enabled just because
COMPILE_TEST is turned on.
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/oe-kbuild-all/202304191106.swKbBeDh-lkp@intel.com/
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Łukasz Stelmach <l.stelmach@samsung.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
cherry pick issue and tested with real hardare and libvirt/qemu plus
swtpm.
-----BEGIN PGP SIGNATURE-----
iIgEABYIADAWIQRE6pSOnaBC00OEHEIaerohdGur0gUCZE55VRIcamFya2tvQGtl
cm5lbC5vcmcACgkQGnq6IXRrq9ILfAD+OPfN2zNx0bAmKB9iRvBulD1P6TIaFUOu
8xrTkCyfPugA/0khCPhEz44RjMkVy8wdpDRalIdo0M4zIf3XSCFJA7oL
=uhNB
-----END PGP SIGNATURE-----
Merge tag 'tpmdd-v6.4-rc1-fix-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/jarkko/linux-tpmdd
Pull tpm fix from Jarkko Sakkinen:
"This fixes a critical bug in my first pull request.
I fixed the cherry pick issue and tested with real hardare and
libvirt/qemu plus swtpm"
* tag 'tpmdd-v6.4-rc1-fix-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/jarkko/linux-tpmdd:
tpm: Re-enable TPM chip boostrapping non-tpm_tis TPM drivers
TPM chip bootstrapping was removed from tpm_chip_register(), and it
was relocated to tpm_tis_core. This breaks all drivers which are not
based on tpm_tis because the chip will not get properly initialized.
Take the corrective steps:
1. Rename tpm_chip_startup() as tpm_chip_bootstrap() and make it one-shot.
2. Call tpm_chip_bootstrap() in tpm_chip_register(), which reverts the
things as tehy used to be.
Cc: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Fixes: 548eb516ec ("tpm, tpm_tis: startup chip before testing for interrupts")
Reported-by: Pengfei Xu <pengfei.xu@intel.com>
Link: https://lore.kernel.org/all/ZEjqhwHWBnxcaRV5@xpf.sh.intel.com/
Tested-by: Pengfei Xu <pengfei.xu@intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Here is the "big" set of char/misc and other driver subsystems for
6.4-rc1.
It's pretty big, but due to the removal of pcmcia drivers, almost breaks
even for number of lines added vs. removed, a nice change.
Included in here are:
- removal of unused PCMCIA drivers (finally!)
- Interconnect driver updates and additions
- Lots of IIO driver updates and additions
- MHI driver updates
- Coresight driver updates
- NVMEM driver updates, which required some OF updates
- W1 driver updates and a new maintainer to manage the subsystem
- FPGA driver updates
- New driver subsystem, CDX, for AMD systems
- lots of other small driver updates and additions
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZEp5Eg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynSXgCg0kSw3vUYwpsnhAsQkoPw1QVA23sAn2edRCMa
GEkPWjrROueCom7xbLMu
=eR+P
-----END PGP SIGNATURE-----
Merge tag 'char-misc-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc drivers updates from Greg KH:
"Here is the "big" set of char/misc and other driver subsystems for
6.4-rc1.
It's pretty big, but due to the removal of pcmcia drivers, almost
breaks even for number of lines added vs. removed, a nice change.
Included in here are:
- removal of unused PCMCIA drivers (finally!)
- Interconnect driver updates and additions
- Lots of IIO driver updates and additions
- MHI driver updates
- Coresight driver updates
- NVMEM driver updates, which required some OF updates
- W1 driver updates and a new maintainer to manage the subsystem
- FPGA driver updates
- New driver subsystem, CDX, for AMD systems
- lots of other small driver updates and additions
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (196 commits)
mcb-lpc: Reallocate memory region to avoid memory overlapping
mcb-pci: Reallocate memory region to avoid memory overlapping
mcb: Return actual parsed size when reading chameleon table
kernel/configs: Drop Android config fragments
virt: acrn: Replace obsolete memalign() with posix_memalign()
spmi: Add a check for remove callback when removing a SPMI driver
spmi: fix W=1 kernel-doc warnings
spmi: mtk-pmif: Drop of_match_ptr for ID table
spmi: pmic-arb: Convert to platform remove callback returning void
spmi: mtk-pmif: Convert to platform remove callback returning void
spmi: hisi-spmi-controller: Convert to platform remove callback returning void
w1: gpio: remove unnecessary ENOMEM messages
w1: omap-hdq: remove unnecessary ENOMEM messages
w1: omap-hdq: add SPDX tag
w1: omap-hdq: allow compile testing
w1: matrox: remove unnecessary ENOMEM messages
w1: matrox: use inline over __inline__
w1: matrox: switch from asm to linux header
w1: ds2482: do not use assignment in if condition
w1: ds2482: drop unnecessary header
...
Here is the large set of driver core changes for 6.4-rc1.
Once again, a busy development cycle, with lots of changes happening in
the driver core in the quest to be able to move "struct bus" and "struct
class" into read-only memory, a task now complete with these changes.
This will make the future rust interactions with the driver core more
"provably correct" as well as providing more obvious lifetime rules for
all busses and classes in the kernel.
The changes required for this did touch many individual classes and
busses as many callbacks were changed to take const * parameters
instead. All of these changes have been submitted to the various
subsystem maintainers, giving them plenty of time to review, and most of
them actually did so.
Other than those changes, included in here are a small set of other
things:
- kobject logging improvements
- cacheinfo improvements and updates
- obligatory fw_devlink updates and fixes
- documentation updates
- device property cleanups and const * changes
- firwmare loader dependency fixes.
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZEp7Sw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykitQCfamUHpxGcKOAGuLXMotXNakTEsxgAoIquENm5
LEGadNS38k5fs+73UaxV
=7K4B
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the large set of driver core changes for 6.4-rc1.
Once again, a busy development cycle, with lots of changes happening
in the driver core in the quest to be able to move "struct bus" and
"struct class" into read-only memory, a task now complete with these
changes.
This will make the future rust interactions with the driver core more
"provably correct" as well as providing more obvious lifetime rules
for all busses and classes in the kernel.
The changes required for this did touch many individual classes and
busses as many callbacks were changed to take const * parameters
instead. All of these changes have been submitted to the various
subsystem maintainers, giving them plenty of time to review, and most
of them actually did so.
Other than those changes, included in here are a small set of other
things:
- kobject logging improvements
- cacheinfo improvements and updates
- obligatory fw_devlink updates and fixes
- documentation updates
- device property cleanups and const * changes
- firwmare loader dependency fixes.
All of these have been in linux-next for a while with no reported
problems"
* tag 'driver-core-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (120 commits)
device property: make device_property functions take const device *
driver core: update comments in device_rename()
driver core: Don't require dynamic_debug for initcall_debug probe timing
firmware_loader: rework crypto dependencies
firmware_loader: Strip off \n from customized path
zram: fix up permission for the hot_add sysfs file
cacheinfo: Add use_arch[|_cache]_info field/function
arch_topology: Remove early cacheinfo error message if -ENOENT
cacheinfo: Check cache properties are present in DT
cacheinfo: Check sib_leaf in cache_leaves_are_shared()
cacheinfo: Allow early level detection when DT/ACPI info is missing/broken
cacheinfo: Add arm64 early level initializer implementation
cacheinfo: Add arch specific early level initializer
tty: make tty_class a static const structure
driver core: class: remove struct class_interface * from callbacks
driver core: class: mark the struct class in struct class_interface constant
driver core: class: make class_register() take a const *
driver core: class: mark class_release() as taking a const *
driver core: remove incorrect comment for device_create*
MIPS: vpe-cmp: remove module owner pointer from struct class usage.
...
Here is the big set of tty/serial driver updates for 6.4-rc1.
Nothing major, just lots of tiny, constant, forward development. This
includes:
- obligatory n_gsm updates and feature additions
- 8250_em driver updates
- sh-sci driver updates
- dts cleanups and updates
- general cleanups and improvements by Ilpo and Jiri
- other small serial driver core fixes and driver updates
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZEqB7w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylQuwCgwU9bGoihDtFsoFYUra/FKPPoC88Anj6t1a1f
X5HZmADnwrFNNq/jP4vH
=FeNF
-----END PGP SIGNATURE-----
Merge tag 'tty-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial updates from Greg KH:
"Here is the big set of tty/serial driver updates for 6.4-rc1.
Nothing major, just lots of tiny, constant, forward development. This
includes:
- obligatory n_gsm updates and feature additions
- 8250_em driver updates
- sh-sci driver updates
- dts cleanups and updates
- general cleanups and improvements by Ilpo and Jiri
- other small serial driver core fixes and driver updates
All of these have been in linux-next for a while with no reported
problems"
* tag 'tty-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (87 commits)
n_gsm: Use array_index_nospec() with index that comes from userspace
tty: vt: drop checks for undefined VT_SINGLE_DRIVER
tty: vt: distribute EXPORT_SYMBOL()
tty: vt: simplify some cases in tioclinux()
tty: vt: reformat tioclinux()
tty: serial: sh-sci: Fix end of transmission on SCI
tty: serial: sh-sci: Add support for tx end interrupt handling
tty: serial: sh-sci: Fix TE setting on SCI IP
tty: serial: sh-sci: Add RZ/G2L SCIFA DMA rx support
tty: serial: sh-sci: Add RZ/G2L SCIFA DMA tx support
serial: max310x: fix IO data corruption in batched operations
serial: core: Disable uart_start() on uart_remove_one_port()
serial: 8250: Reinit port->pm on port specific driver unbind
serial: 8250: Add missing wakeup event reporting
tty: serial: fsl_lpuart: use UARTMODIR register bits for lpuart32 platform
tty: serial: fsl_lpuart: adjust buffer length to the intended size
serial: fix TIOCSRS485 locking
serial: make SiFive serial drivers depend on ARCH_ symbols
tty: synclink_gt: don't allocate and pass dummy flags
tty: serial: simplify qcom_geni_serial_send_chunk_fifo()
...
There was a bug in the SSIF driver where in certain conditions it could
stop working.
Outside of that: spelling fixes, removing some dead code, re-adding a
missing statistic increment, and removal of register_sysctl_table().
-----BEGIN PGP SIGNATURE-----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=ZavT
-----END PGP SIGNATURE-----
Merge tag 'for-linus-6.4-1' of https://github.com/cminyard/linux-ipmi
Pull IPMI updates from Corey Minyard:
"Minor bug fixes for the IPMI driver
There was a bug in the SSIF driver where in certain conditions it
could stop working.
Outside of that: spelling fixes, removing some dead code, re-adding a
missing statistic increment, and removal of register_sysctl_table()"
* tag 'for-linus-6.4-1' of https://github.com/cminyard/linux-ipmi:
ipmi:ssif: Drop if blocks with always false condition
ipmi: fix SSIF not responding under certain cond.
ipmi:ssif: Add send_retries increment
char:ipmi:Fix spelling mistake "asychronously" -> "asynchronously"
ipmi: simplify sysctl registration
ipmi: ASPEED_BT_IPMI_BMC: select REGMAP_MMIO instead of depending on it
API:
- Total usage stats now include all that returned error (instead of some).
- Remove maximum hash statesize limit.
- Add cloning support for hmac and unkeyed hashes.
- Demote BUG_ON in crypto_unregister_alg to a WARN_ON.
Algorithms:
- Use RIP-relative addressing on x86 to prepare for PIE build.
- Add accelerated AES/GCM stitched implementation on powerpc P10.
- Add some test vectors for cmac(camellia).
- Remove failure case where jent is unavailable outside of FIPS mode in drbg.
- Add permanent and intermittent health error checks in jitter RNG.
Drivers:
- Add support for 402xx devices in qat.
- Add support for HiSTB TRNG.
- Fix hash concurrency issues in stm32.
- Add OP-TEE firmware support in caam.
-----BEGIN PGP SIGNATURE-----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=ITkW
-----END PGP SIGNATURE-----
Merge tag 'v6.4-p1' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto updates from Herbert Xu:
"API:
- Total usage stats now include all that returned errors (instead of
just some)
- Remove maximum hash statesize limit
- Add cloning support for hmac and unkeyed hashes
- Demote BUG_ON in crypto_unregister_alg to a WARN_ON
Algorithms:
- Use RIP-relative addressing on x86 to prepare for PIE build
- Add accelerated AES/GCM stitched implementation on powerpc P10
- Add some test vectors for cmac(camellia)
- Remove failure case where jent is unavailable outside of FIPS mode
in drbg
- Add permanent and intermittent health error checks in jitter RNG
Drivers:
- Add support for 402xx devices in qat
- Add support for HiSTB TRNG
- Fix hash concurrency issues in stm32
- Add OP-TEE firmware support in caam"
* tag 'v6.4-p1' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (139 commits)
i2c: designware: Add doorbell support for Mendocino
i2c: designware: Use PCI PSP driver for communication
powerpc: Move Power10 feature PPC_MODULE_FEATURE_P10
crypto: p10-aes-gcm - Remove POWER10_CPU dependency
crypto: testmgr - Add some test vectors for cmac(camellia)
crypto: cryptd - Add support for cloning hashes
crypto: cryptd - Convert hash to use modern init_tfm/exit_tfm
crypto: hmac - Add support for cloning
crypto: hash - Add crypto_clone_ahash/shash
crypto: api - Add crypto_clone_tfm
crypto: api - Add crypto_tfm_get
crypto: x86/sha - Use local .L symbols for code
crypto: x86/crc32 - Use local .L symbols for code
crypto: x86/aesni - Use local .L symbols for code
crypto: x86/sha256 - Use RIP-relative addressing
crypto: x86/ghash - Use RIP-relative addressing
crypto: x86/des3 - Use RIP-relative addressing
crypto: x86/crc32c - Use RIP-relative addressing
crypto: x86/cast6 - Use RIP-relative addressing
crypto: x86/cast5 - Use RIP-relative addressing
...
- Update the ACPICA code in the kernel to upstream revision 20230331
including the following changes:
* Delete bogus node_array array of pointers from AEST table (Jessica
Clarke).
* Add support for trace buffer extension in GICC to the ACPI MADT
parser (Xiongfeng Wang).
* Add missing macro ACPI_FUNCTION_TRACE() for acpi_ns_repair_HID()
(Xiongfeng Wang).
* Add missing tables to astable (Pedro Falcato).
* Add support for 64 bit loong_arch compilation to ACPICA (Huacai
Chen).
* Add support for ASPT table in disassembler to ACPICA (Jeremi
Piotrowski).
* Add support for Arm's MPAM ACPI table version 2 (Hesham Almatary).
* Update all copyrights/signons in ACPICA to 2023 (Bob Moore).
* Add support for ClockInput resource (v6.5) (Niyas Sait).
* Add RISC-V INTC interrupt controller definition to the list of
supported interrupt controllers for MADT (Sunil V L).
* Add structure definitions for the RISC-V RHCT ACPI table (Sunil V L).
* Address several cases in which the ACPICA code might lead to
undefined behavior (Tamir Duberstein).
* Make ACPICA code support flexible arrays properly (Kees Cook).
* Check null return of ACPI_ALLOCATE_ZEROED in
acpi_db_display_objects() (void0red).
* Add os specific support for Zephyr RTOS to ACPICA (Najumon).
* Update version to 20230331 (Bob Moore).
- Fix evaluating the _PDC ACPI control method when running as Xen
dom0 (Roger Pau Monne).
- Use platform devices to load ACPI PPC and PCC drivers (Petr Pavlu).
- Check for null return of devm_kzalloc() in fch_misc_setup() (Kang
Chen).
- Log a message if enable_irq_wake() fails for the ACPI SCI (Simon
Gaiser).
- Initialize the correct IOMMU fwspec while parsing ACPI VIOT
(Jean-Philippe Brucker).
- Amend indentation and prefix error messages with FW_BUG in the ACPI
SPCR parsing code (Andy Shevchenko).
- Enable ACPI sysfs support for CCEL records (Kuppuswamy
Sathyanarayanan).
- Make the APEI error injection code warn on invalid arguments when
explicitly indicated by platform (Shuai Xue).
- Add CXL error types to the error injection code in APEI (Tony Luck).
- Refactor acpi_data_prop_read_single() (Andy Shevchenko).
- Fix two issues in the ACPI SBS driver (Armin Wolf).
- Replace ternary operator with min_t() in the generic ACPI thermal
zone driver (Jiangshan Yi).
- Ensure that ACPI notify handlers are not running after removal and
clean up code in acpi_sb_notify() (Rafael Wysocki).
- Remove register_backlight_delay module option and code and remove
quirks for false-positive backlight control support advertised on
desktop boards (Hans de Goede).
- Replace irqdomain.h include with struct declarations in ACPI headers
and update several pieces of code previously including of.h
implicitly through those headers (Rob Herring).
- Fix acpi_evaluate_dsm_typed() redefinition error (Kiran K).
- Update the pm_profile sysfs attribute documentation (Rafael Wysocki).
- Add 80862289 ACPI _HID for second PWM controller on Cherry Trail to
the ACPI driver for Intel SoCs (Hans de Goede).
-----BEGIN PGP SIGNATURE-----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=O61K
-----END PGP SIGNATURE-----
Merge tag 'acpi-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"These update the ACPICA code in the kernel to upstream revision
20230331, fix the ACPI SBS driver and the evaluation of the _PDC
method on Xen dom0 in the ACPI processor driver, update the ACPI
driver for Intel SoCs and clean up code in multiple places.
Specifics:
- Update the ACPICA code in the kernel to upstream revision 20230331
including the following changes:
* Delete bogus node_array array of pointers from AEST table
(Jessica Clarke)
* Add support for trace buffer extension in GICC to the ACPI MADT
parser (Xiongfeng Wang)
* Add missing macro ACPI_FUNCTION_TRACE() for
acpi_ns_repair_HID() (Xiongfeng Wang)
* Add missing tables to astable (Pedro Falcato)
* Add support for 64 bit loong_arch compilation to ACPICA (Huacai
Chen)
* Add support for ASPT table in disassembler to ACPICA (Jeremi
Piotrowski)
* Add support for Arm's MPAM ACPI table version 2 (Hesham
Almatary)
* Update all copyrights/signons in ACPICA to 2023 (Bob Moore)
* Add support for ClockInput resource (v6.5) (Niyas Sait)
* Add RISC-V INTC interrupt controller definition to the list of
supported interrupt controllers for MADT (Sunil V L)
* Add structure definitions for the RISC-V RHCT ACPI table (Sunil
V L)
* Address several cases in which the ACPICA code might lead to
undefined behavior (Tamir Duberstein)
* Make ACPICA code support flexible arrays properly (Kees Cook)
* Check null return of ACPI_ALLOCATE_ZEROED in
acpi_db_display_objects() (void0red)
* Add os specific support for Zephyr RTOS to ACPICA (Najumon)
* Update version to 20230331 (Bob Moore)
- Fix evaluating the _PDC ACPI control method when running as Xen
dom0 (Roger Pau Monne)
- Use platform devices to load ACPI PPC and PCC drivers (Petr Pavlu)
- Check for null return of devm_kzalloc() in fch_misc_setup() (Kang
Chen)
- Log a message if enable_irq_wake() fails for the ACPI SCI (Simon
Gaiser)
- Initialize the correct IOMMU fwspec while parsing ACPI VIOT
(Jean-Philippe Brucker)
- Amend indentation and prefix error messages with FW_BUG in the ACPI
SPCR parsing code (Andy Shevchenko)
- Enable ACPI sysfs support for CCEL records (Kuppuswamy
Sathyanarayanan)
- Make the APEI error injection code warn on invalid arguments when
explicitly indicated by platform (Shuai Xue)
- Add CXL error types to the error injection code in APEI (Tony Luck)
- Refactor acpi_data_prop_read_single() (Andy Shevchenko)
- Fix two issues in the ACPI SBS driver (Armin Wolf)
- Replace ternary operator with min_t() in the generic ACPI thermal
zone driver (Jiangshan Yi)
- Ensure that ACPI notify handlers are not running after removal and
clean up code in acpi_sb_notify() (Rafael Wysocki)
- Remove register_backlight_delay module option and code and remove
quirks for false-positive backlight control support advertised on
desktop boards (Hans de Goede)
- Replace irqdomain.h include with struct declarations in ACPI
headers and update several pieces of code previously including of.h
implicitly through those headers (Rob Herring)
- Fix acpi_evaluate_dsm_typed() redefinition error (Kiran K)
- Update the pm_profile sysfs attribute documentation (Rafael
Wysocki)
- Add 80862289 ACPI _HID for second PWM controller on Cherry Trail to
the ACPI driver for Intel SoCs (Hans de Goede)"
* tag 'acpi-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (64 commits)
ACPI: LPSS: Add 80862289 ACPI _HID for second PWM controller on Cherry Trail
ACPI: bus: Ensure that notify handlers are not running after removal
ACPI: bus: Add missing braces to acpi_sb_notify()
ACPI: video: Remove desktops without backlight DMI quirks
ACPI: video: Remove register_backlight_delay module option and code
ACPI: Replace irqdomain.h include with struct declarations
fpga: lattice-sysconfig-spi: Add explicit include for of.h
tpm: atmel: Add explicit include for of.h
virtio-mmio: Add explicit include for of.h
pata: ixp4xx: Add explicit include for of.h
ata: pata_macio: Add explicit include of irqdomain.h
serial: 8250_tegra: Add explicit include for of.h
net: rfkill-gpio: Add explicit include for of.h
staging: iio: resolver: ad2s1210: Add explicit include for of.h
iio: adc: ad7292: Add explicit include for of.h
ACPICA: Update version to 20230331
ACPICA: add os specific support for Zephyr RTOS
ACPICA: ACPICA: check null return of ACPI_ALLOCATE_ZEROED in acpi_db_display_objects
ACPICA: acpi_resource_irq: Replace 1-element arrays with flexible array
ACPICA: acpi_madt_oem_data: Fix flexible array member definition
...
ioread8() operations to TPM MMIO addresses can stall the CPU when
immediately following a sequence of iowrite*()'s to the same region.
For example, cyclitest measures ~400us latency spikes when a non-RT
usermode application communicates with an SPI-based TPM chip (Intel Atom
E3940 system, PREEMPT_RT kernel). The spikes are caused by a
stalling ioread8() operation following a sequence of 30+ iowrite8()s to
the same address. I believe this happens because the write sequence is
buffered (in CPU or somewhere along the bus), and gets flushed on the
first LOAD instruction (ioread*()) that follows.
The enclosed change appears to fix this issue: read the TPM chip's
access register (status code) after every iowrite*() operation to
amortize the cost of flushing data to chip across multiple instructions.
Signed-off-by: Haris Okanovic <haris.okanovic@ni.com>
Link: https://lore.kernel.org/r/20230323153436.B2SATnZV@linutronix.de
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
ftpm_tee_remove() returns zero unconditionally (and cannot easily
converted to return void). So ignore the return value to be able to make
ftpm_plat_tee_remove() return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
The driver can be compile tested with !CONFIG_OF or !CONFIG_ACPI making
unused:
drivers/char/tpm/tpm_tis_spi_main.c:234:34: error: ‘of_tis_spi_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
The driver can be compile tested with !CONFIG_OF or !CONFIG_ACPI making
drivers/char/tpm/st33zp24/i2c.c:141:34: error: ‘of_st33zp24_i2c_match’ defined but not used [-Werror=unused-const-variable=]
drivers/char/tpm/st33zp24/spi.c:258:34: error: ‘of_st33zp24_spi_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
The test for interrupts in tpm_tis_send() is skipped if the flag
TPM_CHIP_FLAG_IRQ is not set. Since the current code never sets the flag
initially the test is never executed.
Fix this by setting the flag in tpm_tis_gen_interrupt() right after
interrupts have been enabled and before the test is executed.
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Tested-by: Michael Niewöhner <linux@mniewoehner.de>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
In tpm_tis_gen_interrupt() a request for a property value is sent to the
TPM to test if interrupts are generated. However after a power cycle the
TPM responds with TPM_RC_INITIALIZE which indicates that the TPM is not
yet properly initialized.
Fix this by first starting the TPM up before the request is sent. For this
the startup implementation is removed from tpm_chip_register() and put
into the new function tpm_chip_startup() which is called before the
interrupts are tested.
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
In tpm_tis_resume() make sure that the locality has been claimed when
tpm_tis_reenable_interrupts() is called. Otherwise the writings to the
register might not have any effect.
Fixes: 45baa1d1fa ("tpm_tis: Re-enable interrupts upon (S3) resume")
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Writing the TPM_INT_STATUS register in the interrupt handler to clear the
interrupts only has effect if a locality is held. Since this is not
guaranteed at the time the interrupt is fired, claim the locality
explicitly in the handler.
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Tested-by: Michael Niewöhner <linux@mniewoehner.de>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
The TIS interrupt handler at least has to read and write the interrupt
status register. In case of SPI both operations result in a call to
tpm_tis_spi_transfer() which uses the bus_lock_mutex of the spi device
and thus must only be called from a sleepable context.
To ensure this request a threaded interrupt handler.
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Tested-by: Michael Niewöhner <linux@mniewoehner.de>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Implement a usage counter for the (default) locality used by the TPM TIS
driver:
Request the locality from the TPM if it has not been claimed yet, otherwise
only increment the counter. Also release the locality if the counter is 0
otherwise only decrement the counter. Since in case of SPI the register
accesses are locked by means of the SPI bus mutex use a sleepable lock
(i.e. also a mutex) to ensure thread-safety of the counter which may be
accessed by both a userspace thread and the interrupt handler.
By doing this refactor the names of the amended functions to use a more
appropriate prefix.
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Tested-by: Michael Niewöhner <linux@mniewoehner.de>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
After driver initialization tpm_tis_data->locality may only be modified in
case of a LOCALITY CHANGE interrupt. In this case the interrupt handler
iterates over all localities only to assign the active one to
tpm_tis_data->locality.
However this information is never used any more, so the assignment is not
needed.
Furthermore without the assignment tpm_tis_data->locality cannot change any
more at driver runtime, and thus no protection against concurrent
modification is required when the variable is read at other places.
So remove this iteration entirely.
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Clean up wait_for_tpm_stat() by moving multiple similar interrupt mask
checks into an own function.
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Suggested-by: Jarkko Sakkinen <jarkko@kernel.org>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
According to the TPM Interface Specification (TIS) support for "stsValid"
and "commandReady" interrupts is only optional.
This has to be taken into account when handling the interrupts in functions
like wait_for_tpm_stat(). To determine the supported interrupts use the
capability query.
Also adjust wait_for_tpm_stat() to only wait for interrupt reported status
changes. After that process all the remaining status changes by polling
the status register.
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Tested-by: Michael Niewöhner <linux@mniewoehner.de>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
In tpm_tis_probe_single_irq() interrupt registers TPM_INT_VECTOR,
TPM_INT_STATUS and TPM_INT_ENABLE are modified to setup the interrupts.
Currently these modifications are done without holding a locality thus they
have no effect. Fix this by claiming the (default) locality before the
registers are written.
Since now tpm_tis_gen_interrupt() is called with the locality already
claimed remove locality request and release from this function.
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
If in tpm_tis_probe_irq_single() an error occurs after the original
interrupt vector has been read, restore the interrupts before the error is
returned.
Since the caller does not check the error value, return -1 in any case that
the TPM_CHIP_FLAG_IRQ flag is not set. Since the return value of function
tpm_tis_gen_interrupt() is not longer used, make it a void function.
Fixes: 1107d065fd ("tpm_tis: Introduce intermediate layer for TPM access")
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Both functions tpm_tis_probe_irq_single() and tpm_tis_probe_irq() may setup
the interrupts and then return with an error. This case is indicated by a
missing TPM_CHIP_FLAG_IRQ flag in chip->flags.
Currently the interrupt setup is only undone if tpm_tis_probe_irq_single()
fails. Undo the setup also if tpm_tis_probe_irq() fails.
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Tested-by: Michael Niewöhner <linux@mniewoehner.de>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
In disable_interrupts() the TPM_GLOBAL_INT_ENABLE bit is unset in the
TPM_INT_ENABLE register to shut the interrupts off. However modifying the
register is only possible with a held locality. So claim the locality
before disable_interrupts() is called.
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Tested-by: Michael Niewöhner <linux@mniewoehner.de>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
The interrupt handler that sets the boolean variable irq_tested may run on
another CPU as the thread that checks irq_tested as part of the irq test in
tpm_tis_send().
Since nothing guarantees cache coherency between CPUs for unsynchronized
accesses to boolean variables the testing thread might not perceive the
value change done in the interrupt handler.
Avoid this issue by setting the bit TPM_TIS_IRQ_TESTED in the flags field
of the tpm_tis_data struct and by accessing this field with the bit
manipulating functions that provide cache coherency.
Also convert all other existing sites to use the proper macros when
accessing this bitfield.
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Tested-by: Michael Niewöhner <linux@mniewoehner.de>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Pointer variables of void * type do not require type cast.
Signed-off-by: Yu Zhe <yuzhe@nfschina.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
When waiting for a tpm ready completion, the cr50 i2c driver incorrectly
assumes that the value of timeout_a is represented in milliseconds
instead of jiffies.
Remove the msecs_to_jiffies conversion.
Signed-off-by: Mark Hasemeyer <markhas@chromium.org>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
For both variants (platform and i2c driver) after a successful bind
(i.e. .probe completed without error) driver data is set to a non-NULL
value.
So the return value of i2c_get_clientdata and dev_get_drvdata
respectively are not NULL and so the if blocks are never executed. (And
if you fear they might, they shouldn't return silently and yield a
resource leak.)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Message-Id: <20221230124431.202474-1-u.kleine-koenig@pengutronix.de>
Signed-off-by: Corey Minyard <minyard@acm.org>
The ipmi communication is not restored after a specific version of BMC is
upgraded on our server.
The ipmi driver does not respond after printing the following log:
ipmi_ssif: Invalid response getting flags: 1c 1
I found that after entering this branch, ssif_info->ssif_state always
holds SSIF_GETTING_FLAGS and never return to IDLE.
As a result, the driver cannot be loaded, because the driver status is
checked during the unload process and must be IDLE in shutdown_ssif():
while (ssif_info->ssif_state != SSIF_IDLE)
schedule_timeout(1);
The process trigger this problem is:
1. One msg timeout and next msg start send, and call
ssif_set_need_watch().
2. ssif_set_need_watch()->watch_timeout()->start_flag_fetch() change
ssif_state to SSIF_GETTING_FLAGS.
3. In msg_done_handler() ssif_state == SSIF_GETTING_FLAGS, if an error
message is received, the second branch does not modify the ssif_state.
4. All retry action need IS_SSIF_IDLE() == True. Include retry action in
watch_timeout(), msg_done_handler(). Sending msg does not work either.
SSIF_IDLE is also checked in start_next_msg().
5. The only thing that can be triggered in the SSIF driver is
watch_timeout(), after destory_user(), this timer will stop too.
So, if enter this branch, the ssif_state will remain SSIF_GETTING_FLAGS
and can't send msg, no timer started, can't unload.
We did a comparative test before and after adding this patch, and the
result is effective.
Fixes: 259307074b ("ipmi: Add SMBus interface driver (SSIF)")
Cc: stable@vger.kernel.org
Signed-off-by: Zhang Yuchen <zhangyuchen.lcr@bytedance.com>
Message-Id: <20230412074907.80046-1-zhangyuchen.lcr@bytedance.com>
Signed-off-by: Corey Minyard <minyard@acm.org>
With linux/acpi.h (in linux/tpm.h) no longer implicitly including of.h,
add an explicit include of of.h to fix the following errors:
drivers/char/tpm/tpm_atmel.h:50:14: error: implicit declaration of function 'of_find_node_by_name'; did you mean 'bus_find_device_by_name'? [-Werror=implicit-function-declaration]
drivers/char/tpm/tpm_atmel.h:50:12: error: assignment to 'struct device_node *' from 'int' makes pointer from integer without a cast [-Werror=int-conversion]
drivers/char/tpm/tpm_atmel.h:55:14: error: implicit declaration of function 'of_device_is_compatible'; did you mean 'fwnode_device_is_compatible'? [-Werror=implicit-function-declaration]
...
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We need the fixes in here for testing, as well as the driver core
changes for documentation updates to build on.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pointer variables of void * type do not require type cast.
Signed-off-by: Yu Zhe <yuzhe@nfschina.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Smatch reports:
drivers/char/tpm/tpm-interface.c:470 tpm_init() error:
'tpm_class' dereferencing possible ERR_PTR()
If class_create() returns error pointer, we are dereferencing a possible
error pointer. Fix this by moving the dereference post error handling.
Fixes: a010eb8812 ("tpm: fix up the tpm_class shutdown_pre pointer when created")
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Link: https://lore.kernel.org/r/20230321061416.626561-1-harshit.m.mogalapalli@oracle.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the tty/serial fixes in here and it resolves a merge conflict
with:
drivers/tty/serial/8250/8250_em.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the mainline fixes in this branch for testing and other
subsystem changes to be based properly on.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not wait until long after the struct class has been created to set
the shutdown_pre pointer for the tpm_class, assign it right away.
This is the only in-kernel offender that tries to modify the
device->class pointer contents after it has been assigned to a device,
so fix that up by doing the function pointer assignment before it is
matched with the device. Because of this, the patch should go through
the driver core tree to allow later changes to struct device to be
possible.
Cc: Peter Huewe <peterhuewe@gmx.de>
Cc: Jarkko Sakkinen <jarkko@kernel.org>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: linux-integrity@vger.kernel.org
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Link: https://lore.kernel.org/r/20230313181843.1207845-10-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The module pointer in class_create() never actually did anything, and it
shouldn't have been requred to be set as a parameter even if it did
something. So just remove it and fix up all callers of the function in
the kernel tree at the same time.
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Link: https://lore.kernel.org/r/20230313181843.1207845-4-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
hw_stopped in tty_struct is used like bool, convert the variable type
to bool.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Link: https://lore.kernel.org/r/20230309082035.14880-9-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a spelling mistake in the comment information. Fix it.
Signed-off-by: zipeng zhang <zhangzipeng0@foxmail.com>
Message-Id: <tencent_F0BFF85BC7C1FC84E440A7B7D364D2ED4209@qq.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Use devm_clk_get_optional_enabled() to simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Member pdev isn't used, remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Returning an error value in a platform driver's remove callback results in
a generic error message being emitted by the driver core, but otherwise it
doesn't make a difference. The device goes away anyhow.
As the driver already emits a better error message than the core, suppress
the generic error message by returning zero unconditionally.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
AMD has issued an advisory indicating that having fTPM enabled in
BIOS can cause "stuttering" in the OS. This issue has been fixed
in newer versions of the fTPM firmware, but it's up to system
designers to decide whether to distribute it.
This issue has existed for a while, but is more prevalent starting
with kernel 6.1 because commit b006c439d5 ("hwrng: core - start
hwrng kthread also for untrusted sources") started to use the fTPM
for hwrng by default. However, all uses of /dev/hwrng result in
unacceptable stuttering.
So, simply disable registration of the defective hwrng when detecting
these faulty fTPM versions. As this is caused by faulty firmware, it
is plausible that such a problem could also be reproduced by other TPM
interactions, but this hasn't been shown by any user's testing or reports.
It is hypothesized to be triggered more frequently by the use of the RNG
because userspace software will fetch random numbers regularly.
Intentionally continue to register other TPM functionality so that users
that rely upon PCR measurements or any storage of data will still have
access to it. If it's found later that another TPM functionality is
exacerbating this problem a module parameter it can be turned off entirely
and a module parameter can be introduced to allow users who rely upon
fTPM functionality to turn it on even though this problem is present.
Link: https://www.amd.com/en/support/kb/faq/pa-410
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216989
Link: https://lore.kernel.org/all/20230209153120.261904-1-Jason@zx2c4.com/
Fixes: b006c439d5 ("hwrng: core - start hwrng kthread also for untrusted sources")
Cc: stable@vger.kernel.org
Cc: Jarkko Sakkinen <jarkko@kernel.org>
Cc: Thorsten Leemhuis <regressions@leemhuis.info>
Cc: James Bottomley <James.Bottomley@hansenpartnership.com>
Tested-by: reach622@mailcuk.com
Tested-by: Bell <1138267643@qq.com>
Co-developed-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Instead of ignoring errors returned by devm_clk_get() and manually
enabling the clk for the whole lifetime of the bound device, use
devm_clk_get_optional_enabled(). This is simpler and also more correct
as it doesn't ignore errors. This is also more correct because now the
call to clk_disable_unprepare() can be dropped from xgene_rng_remove()
which happened while the hwrn device was still registered. With the devm
callback disabling the clk happens correctly only after
devm_hwrng_register() is undone.
As a result struct xgene_rng_dev::clk is only used in xgene_rng_probe, and
so the struct member can be replaced by a local variable.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
dev_err_probe simplifies the idiom:
if (ret != -EPROBE_DEFER)
dev_err(...)
return ret;
, emits the error code in a human readable way and even yields a useful
entry in /sys/kernel/debug/devices_deferred in the EPROBE_DEFER case.
So simplify and at the same time improve the driver by using
dev_err_probe().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
These char PCMCIA drivers are buggy[1] and receive only minimal care. It
was concluded[2], that we should try to remove most pcmcia drivers
completely. Let's start with these char broken one.
Note that I also removed a UAPI header: include/uapi/linux/cm4000_cs.h.
I found only coccinelle tests mentioning some ioctl constants from that
file. But they are not actually used. Anyway, should someone complain,
we may reintroduce the header (or its parts).
[1] https://lore.kernel.org/all/f41c2765-80e0-48bc-b1e4-8cfd3230fd4a@www.fastmail.com/
[2] https://lore.kernel.org/all/c5b39544-a4fb-4796-a046-0b9be9853787@app.fastmail.com/
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Cc: "Hyunwoo Kim" <imv4bel@gmail.com>
Cc: Harald Welte <laforge@gnumonks.org>
Cc: Lubomir Rintel <lkundrak@v3.sk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230222092302.6348-2-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ipwireless' Kconfig entry is currently sitting in char/pcmcia. But
the driver is in tty/. So move the entry to tty/ too.
First, it makes sense to have the entry along the driver. Second, whole
char/pcmcia is about to pass away.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: David Sterba <dsterba@suse.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: David Sterba <dsterba@suse.com>
Link: https://lore.kernel.org/r/20230222092302.6348-1-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It turns out that commit 596ff4a09b ("cpumask: re-introduce
constant-sized cpumask optimizations") exposed a number of cases of
drivers not checking the result of "cpumask_next()" and friends
correctly.
The documented correct check for "no more cpus in the cpumask" is to
check for the result being equal or larger than the number of possible
CPU ids, exactly _because_ we've always done those constant-sized
cpumask scans using a widened type before. So the return value of a
cpumask scan should be checked with
if (cpu >= nr_cpu_ids)
...
because the cpumask scan did not necessarily stop exactly *at* that
maximum CPU id.
But a few cases ended up instead using checks like
if (cpu == nr_cpumask_bits)
...
which used that internal "widened" number of bits. And that used to
work pretty much by accident (ok, in this case "by accident" is simply
because it matched the historical internal implementation of the cpumask
scanning, so it was more of a "intentionally using implementation
details rather than an accident").
But the extended constant-sized optimizations then did that internal
implementation differently, and now that code that did things wrong but
matched the old implementation no longer worked at all.
Which then causes subsequent odd problems due to using what ends up
being an invalid CPU ID.
Most of these cases require either unusual hardware or special uses to
hit, but the random.c one triggers quite easily.
All you really need is to have a sufficiently small CONFIG_NR_CPUS value
for the bit scanning optimization to be triggered, but not enough CPUs
to then actually fill that widened cpumask. At that point, the cpumask
scanning will return the NR_CPUS constant, which is _not_ the same as
nr_cpumask_bits.
This just does the mindless fix with
sed -i 's/== nr_cpumask_bits/>= nr_cpu_ids/'
to fix the incorrect uses.
The ones in the SCSI lpfc driver in particular could probably be fixed
more cleanly by just removing that repeated pattern entirely, but I am
not emptionally invested enough in that driver to care.
Reported-and-tested-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/lkml/481b19b5-83a0-4793-b4fd-194ad7b978c3@roeck-us.net/
Reported-and-tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/lkml/CAMuHMdUKo_Sf7TjKzcNDa8Ve+6QrK+P8nSQrSQ=6LTRmcBKNww@mail.gmail.com/
Reported-by: Vernon Yang <vernon2gm@gmail.com>
Link: https://lore.kernel.org/lkml/20230306160651.2016767-1-vernon2gm@gmail.com/
Cc: Yury Norov <yury.norov@gmail.com>
Cc: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
register_sysctl_table() is a deprecated compatibility wrapper.
register_sysctl() can do the directory creation for you so just use
that.
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Message-Id: <20230302204612.782387-3-mcgrof@kernel.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
REGMAP is a hidden (not user visible) symbol. Users cannot set it
directly thru "make *config", so drivers should select it instead of
depending on it if they need it.
Consistently using "select" or "depends on" can also help reduce
Kconfig circular dependency issues.
Therefore, change the use of "depends on REGMAP_MMIO" to
"select REGMAP_MMIO", which will also set REGMAP.
Fixes: eb994594bc ("ipmi: bt-bmc: Use a regmap for register access")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Andrew Jeffery <andrew@aj.id.au>
Cc: Corey Minyard <minyard@acm.org>
Cc: openipmi-developer@lists.sourceforge.net
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Message-Id: <20230226053953.4681-2-rdunlap@infradead.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Here is the large set of driver changes for char/misc drivers and other
smaller driver subsystems that flow through this git tree.
Included in here are:
- New IIO drivers and features and improvments in that subsystem
- New hwtracing drivers and additions to that subsystem
- lots of interconnect changes and new drivers as that subsystem seems
under very active development recently. This required also merging
in the icc subsystem changes through this tree.
- FPGA driver updates
- counter subsystem and driver updates
- MHI driver updates
- nvmem driver updates
- documentation updates
- Other smaller driver updates and fixes, full details in the shortlog
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY/inQw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yksvwCeOvU//SPwrbIpaeHAmHUv0PSVOrwAoKmt4ICh
hQUudlztfkvUJxKIH0gh
=Sjk4
-----END PGP SIGNATURE-----
Merge tag 'char-misc-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc and other driver subsystem updates from Greg KH:
"Here is the large set of driver changes for char/misc drivers and
other smaller driver subsystems that flow through this git tree.
Included in here are:
- New IIO drivers and features and improvments in that subsystem
- New hwtracing drivers and additions to that subsystem
- lots of interconnect changes and new drivers as that subsystem
seems under very active development recently. This required also
merging in the icc subsystem changes through this tree.
- FPGA driver updates
- counter subsystem and driver updates
- MHI driver updates
- nvmem driver updates
- documentation updates
- Other smaller driver updates and fixes, full details in the
shortlog
All of these have been in linux-next for a while with no reported
problems"
* tag 'char-misc-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (223 commits)
scripts/tags.sh: fix incompatibility with PCRE2
firmware: coreboot: Remove GOOGLE_COREBOOT_TABLE_ACPI/OF Kconfig entries
mei: lower the log level for non-fatal failed messages
mei: bus: disallow driver match while dismantling device
misc: vmw_balloon: fix memory leak with using debugfs_lookup()
nvmem: stm32: fix OPTEE dependency
dt-bindings: nvmem: qfprom: add IPQ8074 compatible
nvmem: qcom-spmi-sdam: register at device init time
nvmem: rave-sp-eeprm: fix kernel-doc bad line warning
nvmem: stm32: detect bsec pta presence for STM32MP15x
nvmem: stm32: add OP-TEE support for STM32MP13x
nvmem: core: use nvmem_add_one_cell() in nvmem_add_cells_from_of()
nvmem: core: add nvmem_add_one_cell()
nvmem: core: drop the removal of the cells in nvmem_add_cells()
nvmem: core: move struct nvmem_cell_info to nvmem-provider.h
nvmem: core: add an index parameter to the cell
of: property: add #nvmem-cell-cells property
of: property: make #.*-cells optional for simple props
of: base: add of_parse_phandle_with_optional_args()
net: add helper eth_addr_add()
...
Here is the big set of serial and tty driver updates for 6.3-rc1.
Once again, Jiri and Ilpo have done a number of core vt and tty/serial
layer cleanups that were much needed and appreciated. Other than that,
it's just a bunch of little tty/serial driver updates:
- qcom-geni-serial driver updates
- liteuart driver updates
- hvcs driver cleanups
- n_gsm updates and additions for new features
- more 8250 device support added
- fpga/dfl update and additions
- imx serial driver updates
- fsl_lpuart updates
- other tiny fixes and updates for serial drivers
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY/itAw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykJbQCfWv/J4ZElO108iHBU5mJCDagUDBgAnAtLLN6A
SEAnnokGCDtA/BNIXeES
=luRi
-----END PGP SIGNATURE-----
Merge tag 'tty-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver updates from Greg KH:
"Here is the big set of serial and tty driver updates for 6.3-rc1.
Once again, Jiri and Ilpo have done a number of core vt and tty/serial
layer cleanups that were much needed and appreciated. Other than that,
it's just a bunch of little tty/serial driver updates:
- qcom-geni-serial driver updates
- liteuart driver updates
- hvcs driver cleanups
- n_gsm updates and additions for new features
- more 8250 device support added
- fpga/dfl update and additions
- imx serial driver updates
- fsl_lpuart updates
- other tiny fixes and updates for serial drivers
All of these have been in linux-next for a while with no reported
problems"
* tag 'tty-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (143 commits)
tty: n_gsm: add keep alive support
serial: imx: remove a redundant check
dt-bindings: serial: snps-dw-apb-uart: add dma & dma-names properties
soc: qcom: geni-se: Move qcom-geni-se.h to linux/soc/qcom/geni-se.h
tty: n_gsm: add TIOCMIWAIT support
tty: n_gsm: add RING/CD control support
tty: n_gsm: mark unusable ioctl structure fields accordingly
serial: imx: get rid of registers shadowing
serial: imx: refine local variables in rxint()
serial: imx: stop using USR2 in FIFO reading loop
serial: imx: remove redundant USR2 read from FIFO reading loop
serial: imx: do not break from FIFO reading loop prematurely
serial: imx: do not sysrq broken chars
serial: imx: work-around for hardware RX flood
serial: imx: factor-out common code to imx_uart_soft_reset()
serial: 8250_pci1xxxx: Add power management functions to quad-uart driver
serial: 8250_pci1xxxx: Add RS485 support to quad-uart driver
serial: 8250_pci1xxxx: Add driver for quad-uart support
serial: 8250_pci: Add serial8250_pci_setup_port definition in 8250_pcilib.c
tty: pcn_uart: fix memory leak with using debugfs_lookup()
...
F_SEAL_EXEC") which permits the setting of the memfd execute bit at
memfd creation time, with the option of sealing the state of the X bit.
- Peter Xu adds a patch series ("mm/hugetlb: Make huge_pte_offset()
thread-safe for pmd unshare") which addresses a rare race condition
related to PMD unsharing.
- Several folioification patch serieses from Matthew Wilcox, Vishal
Moola, Sidhartha Kumar and Lorenzo Stoakes
- Johannes Weiner has a series ("mm: push down lock_page_memcg()") which
does perform some memcg maintenance and cleanup work.
- SeongJae Park has added DAMOS filtering to DAMON, with the series
"mm/damon/core: implement damos filter". These filters provide users
with finer-grained control over DAMOS's actions. SeongJae has also done
some DAMON cleanup work.
- Kairui Song adds a series ("Clean up and fixes for swap").
- Vernon Yang contributed the series "Clean up and refinement for maple
tree".
- Yu Zhao has contributed the "mm: multi-gen LRU: memcg LRU" series. It
adds to MGLRU an LRU of memcgs, to improve the scalability of global
reclaim.
- David Hildenbrand has added some userfaultfd cleanup work in the
series "mm: uffd-wp + change_protection() cleanups".
- Christoph Hellwig has removed the generic_writepages() library
function in the series "remove generic_writepages".
- Baolin Wang has performed some maintenance on the compaction code in
his series "Some small improvements for compaction".
- Sidhartha Kumar is doing some maintenance work on struct page in his
series "Get rid of tail page fields".
- David Hildenbrand contributed some cleanup, bugfixing and
generalization of pte management and of pte debugging in his series "mm:
support __HAVE_ARCH_PTE_SWP_EXCLUSIVE on all architectures with swap
PTEs".
- Mel Gorman and Neil Brown have removed the __GFP_ATOMIC allocation
flag in the series "Discard __GFP_ATOMIC".
- Sergey Senozhatsky has improved zsmalloc's memory utilization with his
series "zsmalloc: make zspage chain size configurable".
- Joey Gouly has added prctl() support for prohibiting the creation of
writeable+executable mappings. The previous BPF-based approach had
shortcomings. See "mm: In-kernel support for memory-deny-write-execute
(MDWE)".
- Waiman Long did some kmemleak cleanup and bugfixing in the series
"mm/kmemleak: Simplify kmemleak_cond_resched() & fix UAF".
- T.J. Alumbaugh has contributed some MGLRU cleanup work in his series
"mm: multi-gen LRU: improve".
- Jiaqi Yan has provided some enhancements to our memory error
statistics reporting, mainly by presenting the statistics on a per-node
basis. See the series "Introduce per NUMA node memory error
statistics".
- Mel Gorman has a second and hopefully final shot at fixing a CPU-hog
regression in compaction via his series "Fix excessive CPU usage during
compaction".
- Christoph Hellwig does some vmalloc maintenance work in the series
"cleanup vfree and vunmap".
- Christoph Hellwig has removed block_device_operations.rw_page() in ths
series "remove ->rw_page".
- We get some maple_tree improvements and cleanups in Liam Howlett's
series "VMA tree type safety and remove __vma_adjust()".
- Suren Baghdasaryan has done some work on the maintainability of our
vm_flags handling in the series "introduce vm_flags modifier functions".
- Some pagemap cleanup and generalization work in Mike Rapoport's series
"mm, arch: add generic implementation of pfn_valid() for FLATMEM" and
"fixups for generic implementation of pfn_valid()"
- Baoquan He has done some work to make /proc/vmallocinfo and
/proc/kcore better represent the real state of things in his series
"mm/vmalloc.c: allow vread() to read out vm_map_ram areas".
- Jason Gunthorpe rationalized the GUP system's interface to the rest of
the kernel in the series "Simplify the external interface for GUP".
- SeongJae Park wishes to migrate people from DAMON's debugfs interface
over to its sysfs interface. To support this, we'll temporarily be
printing warnings when people use the debugfs interface. See the series
"mm/damon: deprecate DAMON debugfs interface".
- Andrey Konovalov provided the accurately named "lib/stackdepot: fixes
and clean-ups" series.
- Huang Ying has provided a dramatic reduction in migration's TLB flush
IPI rates with the series "migrate_pages(): batch TLB flushing".
- Arnd Bergmann has some objtool fixups in "objtool warning fixes".
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCY/PoPQAKCRDdBJ7gKXxA
jlvpAPsFECUBBl20qSue2zCYWnHC7Yk4q9ytTkPB/MMDrFEN9wD/SNKEm2UoK6/K
DmxHkn0LAitGgJRS/W9w81yrgig9tAQ=
=MlGs
-----END PGP SIGNATURE-----
Merge tag 'mm-stable-2023-02-20-13-37' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull MM updates from Andrew Morton:
- Daniel Verkamp has contributed a memfd series ("mm/memfd: add
F_SEAL_EXEC") which permits the setting of the memfd execute bit at
memfd creation time, with the option of sealing the state of the X
bit.
- Peter Xu adds a patch series ("mm/hugetlb: Make huge_pte_offset()
thread-safe for pmd unshare") which addresses a rare race condition
related to PMD unsharing.
- Several folioification patch serieses from Matthew Wilcox, Vishal
Moola, Sidhartha Kumar and Lorenzo Stoakes
- Johannes Weiner has a series ("mm: push down lock_page_memcg()")
which does perform some memcg maintenance and cleanup work.
- SeongJae Park has added DAMOS filtering to DAMON, with the series
"mm/damon/core: implement damos filter".
These filters provide users with finer-grained control over DAMOS's
actions. SeongJae has also done some DAMON cleanup work.
- Kairui Song adds a series ("Clean up and fixes for swap").
- Vernon Yang contributed the series "Clean up and refinement for maple
tree".
- Yu Zhao has contributed the "mm: multi-gen LRU: memcg LRU" series. It
adds to MGLRU an LRU of memcgs, to improve the scalability of global
reclaim.
- David Hildenbrand has added some userfaultfd cleanup work in the
series "mm: uffd-wp + change_protection() cleanups".
- Christoph Hellwig has removed the generic_writepages() library
function in the series "remove generic_writepages".
- Baolin Wang has performed some maintenance on the compaction code in
his series "Some small improvements for compaction".
- Sidhartha Kumar is doing some maintenance work on struct page in his
series "Get rid of tail page fields".
- David Hildenbrand contributed some cleanup, bugfixing and
generalization of pte management and of pte debugging in his series
"mm: support __HAVE_ARCH_PTE_SWP_EXCLUSIVE on all architectures with
swap PTEs".
- Mel Gorman and Neil Brown have removed the __GFP_ATOMIC allocation
flag in the series "Discard __GFP_ATOMIC".
- Sergey Senozhatsky has improved zsmalloc's memory utilization with
his series "zsmalloc: make zspage chain size configurable".
- Joey Gouly has added prctl() support for prohibiting the creation of
writeable+executable mappings.
The previous BPF-based approach had shortcomings. See "mm: In-kernel
support for memory-deny-write-execute (MDWE)".
- Waiman Long did some kmemleak cleanup and bugfixing in the series
"mm/kmemleak: Simplify kmemleak_cond_resched() & fix UAF".
- T.J. Alumbaugh has contributed some MGLRU cleanup work in his series
"mm: multi-gen LRU: improve".
- Jiaqi Yan has provided some enhancements to our memory error
statistics reporting, mainly by presenting the statistics on a
per-node basis. See the series "Introduce per NUMA node memory error
statistics".
- Mel Gorman has a second and hopefully final shot at fixing a CPU-hog
regression in compaction via his series "Fix excessive CPU usage
during compaction".
- Christoph Hellwig does some vmalloc maintenance work in the series
"cleanup vfree and vunmap".
- Christoph Hellwig has removed block_device_operations.rw_page() in
ths series "remove ->rw_page".
- We get some maple_tree improvements and cleanups in Liam Howlett's
series "VMA tree type safety and remove __vma_adjust()".
- Suren Baghdasaryan has done some work on the maintainability of our
vm_flags handling in the series "introduce vm_flags modifier
functions".
- Some pagemap cleanup and generalization work in Mike Rapoport's
series "mm, arch: add generic implementation of pfn_valid() for
FLATMEM" and "fixups for generic implementation of pfn_valid()"
- Baoquan He has done some work to make /proc/vmallocinfo and
/proc/kcore better represent the real state of things in his series
"mm/vmalloc.c: allow vread() to read out vm_map_ram areas".
- Jason Gunthorpe rationalized the GUP system's interface to the rest
of the kernel in the series "Simplify the external interface for
GUP".
- SeongJae Park wishes to migrate people from DAMON's debugfs interface
over to its sysfs interface. To support this, we'll temporarily be
printing warnings when people use the debugfs interface. See the
series "mm/damon: deprecate DAMON debugfs interface".
- Andrey Konovalov provided the accurately named "lib/stackdepot: fixes
and clean-ups" series.
- Huang Ying has provided a dramatic reduction in migration's TLB flush
IPI rates with the series "migrate_pages(): batch TLB flushing".
- Arnd Bergmann has some objtool fixups in "objtool warning fixes".
* tag 'mm-stable-2023-02-20-13-37' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (505 commits)
include/linux/migrate.h: remove unneeded externs
mm/memory_hotplug: cleanup return value handing in do_migrate_range()
mm/uffd: fix comment in handling pte markers
mm: change to return bool for isolate_movable_page()
mm: hugetlb: change to return bool for isolate_hugetlb()
mm: change to return bool for isolate_lru_page()
mm: change to return bool for folio_isolate_lru()
objtool: add UACCESS exceptions for __tsan_volatile_read/write
kmsan: disable ftrace in kmsan core code
kasan: mark addr_has_metadata __always_inline
mm: memcontrol: rename memcg_kmem_enabled()
sh: initialize max_mapnr
m68k/nommu: add missing definition of ARCH_PFN_OFFSET
mm: percpu: fix incorrect size in pcpu_obj_full_size()
maple_tree: reduce stack usage with gcc-9 and earlier
mm: page_alloc: call panic() when memoryless node allocation fails
mm: multi-gen LRU: avoid futile retries
migrate_pages: move THP/hugetlb migration support check to simplify code
migrate_pages: batch flushing TLB
migrate_pages: share more code between _unmap and _move
...
Nothing big, cleanups, fixing names, and one small deviation from the
specification fixed.
-----BEGIN PGP SIGNATURE-----
iQIyBAABCgAdFiEE/Q1c5nzg9ZpmiCaGYfOMkJGb/4EFAmP2DPYACgkQYfOMkJGb
/4G+1w/1E3mqdn1P4pq9pcsTZRRRfrLxMYQAaZMOZu6cb/mOL1Bj0D/Ks/q9bkkF
1iCSYUgca6TVSmnF0o23cP2Q4cGmH4vEk/e1L5XF3A/gXJ1KK6T1p5g/pYhyIJze
WRO/r1OKPvfsD+djkslafMlzE1lwKGQa4hlwXAkmeSZn5cijB4BKeh+i8Sv2C0ER
PX8Ar3TTXrfSragXjzZdbXOksT4kskGpPkAYSwWj2dRM9+Sh2ReoOr0xiCy5Wnm6
gCVtjrPiVdtlAUi3OriUR1/IJjvWXuDBVFCKpd/w8urK61BsoMmrUVb319GOYH94
UTIz8SyxOaS8E3v46ToRrQHRvjlBNMQY3BrYMxfVp1NmR1VRJycPgKfviV0dezmK
CvObTTK9JscSJ2BlmZ+u9sC4pN9OQCoA988B91plJ9X5GGI4VH/aQ+EN7XIjrRn7
09QV9OyW56yFdtgIWcvH8dwpsQQD4T1H7aWe50BtL6Z+NB8HnV6h9suSh9+Q6jgr
K7MNXWgxVvKs+MolbuUNJ6iWYTwgcAIz/21h2deZrtQ6vXKZFyQBHzGiN9We6nwz
J/Pbz4R4pE7l/zsP+yNdPi7XRa8uieNOXbp3GoorhRBPyQC38AWJTUh4FybOEB9V
Gj/iDAm6L6VRwTSXYarFvmU1vq/EPVHTGZ3Vz6Mam62JXFoShQ==
=qBVV
-----END PGP SIGNATURE-----
Merge tag 'for-linus-6.3-1' of https://github.com/cminyard/linux-ipmi
Pull IPMI updates from Corey Minyard:
"Small fixes to the SMBus IPMI and IPMB driver.
Nothing big, cleanups, fixing names, and one small deviation from the
specification fixed"
* tag 'for-linus-6.3-1' of https://github.com/cminyard/linux-ipmi:
ipmi: ipmb: Fix the MODULE_PARM_DESC associated to 'retry_time_ms'
ipmi:ssif: Add a timer between request retries
ipmi:ssif: Remove rtc_us_timer
ipmi_ssif: Rename idle state and check
ipmi:ssif: resend_msg() cannot fail
API:
- Use kmap_local instead of kmap_atomic.
- Change request callback to take void pointer.
- Print FIPS status in /proc/crypto (when enabled).
Algorithms:
- Add rfc4106/gcm support on arm64.
- Add ARIA AVX2/512 support on x86.
Drivers:
- Add TRNG driver for StarFive SoC.
- Delete ux500/hash driver (subsumed by stm32/hash).
- Add zlib support in qat.
- Add RSA support in aspeed.
-----BEGIN PGP SIGNATURE-----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=dMYe
-----END PGP SIGNATURE-----
Merge tag 'v6.3-p1' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto update from Herbert Xu:
"API:
- Use kmap_local instead of kmap_atomic
- Change request callback to take void pointer
- Print FIPS status in /proc/crypto (when enabled)
Algorithms:
- Add rfc4106/gcm support on arm64
- Add ARIA AVX2/512 support on x86
Drivers:
- Add TRNG driver for StarFive SoC
- Delete ux500/hash driver (subsumed by stm32/hash)
- Add zlib support in qat
- Add RSA support in aspeed"
* tag 'v6.3-p1' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (156 commits)
crypto: x86/aria-avx - Do not use avx2 instructions
crypto: aspeed - Fix modular aspeed-acry
crypto: hisilicon/qm - fix coding style issues
crypto: hisilicon/qm - update comments to match function
crypto: hisilicon/qm - change function names
crypto: hisilicon/qm - use min() instead of min_t()
crypto: hisilicon/qm - remove some unused defines
crypto: proc - Print fips status
crypto: crypto4xx - Call dma_unmap_page when done
crypto: octeontx2 - Fix objects shared between several modules
crypto: nx - Fix sparse warnings
crypto: ecc - Silence sparse warning
tls: Pass rec instead of aead_req into tls_encrypt_done
crypto: api - Remove completion function scaffolding
tls: Remove completion function scaffolding
tipc: Remove completion function scaffolding
net: ipv6: Remove completion function scaffolding
net: ipv4: Remove completion function scaffolding
net: macsec: Remove completion function scaffolding
dm: Remove completion function scaffolding
...
Only three minor changes: a cross-platform series from Mike Rapoport to
consolidate asm/agp.h between architectures, and a correctness change
for __generic_cmpxchg_local() from Matt Evans.
-----BEGIN PGP SIGNATURE-----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=3646
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic cleanups from Arnd Bergmann:
"Only three minor changes: a cross-platform series from Mike Rapoport
to consolidate asm/agp.h between architectures, and a correctness
change for __generic_cmpxchg_local() from Matt Evans"
* tag 'asm-generic-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
char/agp: introduce asm-generic/agp.h
char/agp: consolidate {alloc,free}_gatt_pages()
locking/atomic: cmpxchg: Make __generic_cmpxchg_local compare against zero-extended 'old' value
There is a copy of alloc_gatt_pages() and free_gatt_pages in several
architectures in arch/$ARCH/include/asm/agp.h. All the copies do exactly
the same: alias alloc_gatt_pages() to __get_free_pages(GFP_KERNEL) and
alias free_gatt_pages() to free_pages().
Define alloc_gatt_pages() and free_gatt_pages() in drivers/char/agp/agp.h
and drop per-architecture definitions.
Signed-off-by: Mike Rapoport (IBM) <rppt@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Some TPM 2.0 devices have support for additional commands which are not
part of the TPM 2.0 specifications.
These commands are identified with bit 29 of the 32 bits command codes.
Contrarily to other fields of the TPMA_CC spec structure used to list
available commands, the Vendor flag also has to be present in the
command code itself (TPM_CC) when called.
Add this flag to tpm_find_cc() mask to prevent blocking vendor command
codes that can actually be supported by the underlying TPM device.
Signed-off-by: Julien Gomes <julien@arista.com>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Some platforms may desire to pass the event log up to Linux in the
form of a reserved memory region. In particular, this is desirable
for embedded systems or baseboard management controllers (BMCs)
booting with U-Boot. IBM OpenBMC BMCs will be the first user.
Add support for the reserved memory in the TPM core to find the
region and map it.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
[jarkko: removed spurious dev_info()'s from tpm_read_log_memory_region()]
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
[yang: return -ENOMEM when devm_memremap() fails]
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Since the bios event log is freed in the device release function,
let devres handle the deallocation. This will allow other memory
allocation/mapping functions to be used for the bios event log.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Pluton is an integrated security processor present in some recent Ryzen
parts. If it's enabled, it presents two devices - an MSFT0101 ACPI device
that's broadly an implementation of a Command Response Buffer TPM2, and an
MSFT0200 ACPI device whose functionality I haven't examined in detail yet.
This patch only attempts to add support for the TPM device.
There's a few things that need to be handled here. The first is that the
TPM2 ACPI table uses a previously undefined start method identifier. The
table format appears to include 16 bytes of startup data, which corresponds
to one 64-bit address for a start message and one 64-bit address for a
completion response. The second is that the ACPI tables on the Thinkpad Z13
I'm testing this on don't define any memory windows in _CRS (or, more
accurately, there are two empty memory windows). This check doesn't seem
strictly necessary, so I've skipped that.
Finally, it seems like chip needs to be explicitly asked to transition into
ready status on every command. Failing to do this means that if two
commands are sent in succession without an idle/ready transition in
between, everything will appear to work fine but the response is simply the
original command. I'm working without any docs here, so I'm not sure if
this is actually the required behaviour or if I'm missing something
somewhere else, but doing this results in the chip working reliably.
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
'This should be 'retry_time_ms' instead of 'max_retries'.
Fixes: 63c4eb3471 ("ipmi:ipmb: Add initial support for IPMI over IPMB")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Message-Id: <0d8670cff2c656e99a832a249e77dc90578f67de.1675591429.git.christophe.jaillet@wanadoo.fr>
Cc: stable@vger.kernel.org
Signed-off-by: Corey Minyard <cminyard@mvista.com>
The IPMI spec has a time (T6) specified between request retries. Add
the handling for that.
Reported by: Tony Camuso <tcamuso@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Rename the SSIF_IDLE() to IS_SSIF_IDLE(), since that is more clear, and
rename SSIF_NORMAL to SSIF_IDLE, since that's more accurate.
Cc: stable@vger.kernel.org
Signed-off-by: Corey Minyard <cminyard@mvista.com>
The resend_msg() function cannot fail, but there was error handling
around using it. Rework the handling of the error, and fix the out of
retries debug reporting that was wrong around this, too.
Cc: stable@vger.kernel.org
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Replace direct modifications to vma->vm_flags with calls to modifier
functions to be able to track flag changes and to keep vma locking
correctness.
[akpm@linux-foundation.org: fix drivers/misc/open-dice.c, per Hyeonggon Yoo]
Link: https://lkml.kernel.org/r/20230126193752.297968-5-surenb@google.com
Signed-off-by: Suren Baghdasaryan <surenb@google.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Mike Rapoport (IBM) <rppt@kernel.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Liam R. Howlett <Liam.Howlett@Oracle.com>
Reviewed-by: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arjun Roy <arjunroy@google.com>
Cc: Axel Rasmussen <axelrasmussen@google.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: David Rientjes <rientjes@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Greg Thelen <gthelen@google.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jann Horn <jannh@google.com>
Cc: Joel Fernandes <joelaf@google.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Kent Overstreet <kent.overstreet@linux.dev>
Cc: Laurent Dufour <ldufour@linux.ibm.com>
Cc: Lorenzo Stoakes <lstoakes@gmail.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Minchan Kim <minchan@google.com>
Cc: Paul E. McKenney <paulmck@kernel.org>
Cc: Peter Oskolkov <posk@google.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Punit Agrawal <punit.agrawal@bytedance.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Cc: Song Liu <songliubraving@fb.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Enable compile testing for jh7110. Also remove the dependency on
HW_RANDOM.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Jia Jie Ho <jiajie.ho@starfivetech.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This adds driver support for the hardware random number generator in
Starfive SoCs and adds StarFive TRNG entry to MAINTAINERS.
Co-developed-by: Jenny Zhang <jenny.zhang@starfivetech.com>
Signed-off-by: Jenny Zhang <jenny.zhang@starfivetech.com>
Signed-off-by: Jia Jie Ho <jiajie.ho@starfivetech.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The implementation of strscpy() is more robust and safer.
That's now the recommended way to copy NUL-terminated strings.
Signed-off-by: Bo Liu <liubo03@inspur.com>
Link: https://lore.kernel.org/r/20230118012944.2436-1-liubo03@inspur.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As comment of pci_get_class() says, it returns a pci_device with its
refcount increased and decreased the refcount for the input parameter
@from if it is not NULL.
If we break the loop in applicom_init() with 'dev' not NULL, we need to
call pci_dev_put() to decrease the refcount. Add the missing
pci_dev_put() to avoid refcount leak.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Link: https://lore.kernel.org/r/20221122114035.24194-1-wangxiongfeng2@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit be826ada52.
The function monitor_card() is a timer handler that runs in an
atomic context, but it calls usleep_range() that can sleep.
As a result, the sleep-in-atomic-context bugs will happen.
The process is shown below:
(atomic context)
monitor_card()
set_protocol()
usleep_range() //sleep
The origin commit c1986ee9be ("[PATCH] New Omnikey Cardman
4000 driver") works fine.
Fixes: be826ada52 ("char: pcmcia: cm4000_cs: Replace mdelay with usleep_range in set_protocol")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Link: https://lore.kernel.org/r/20230118141000.5580-1-duoming@zju.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove all kernel-doc "/**" markers; just use "/*" comments since
these are not in kernel-doc format.
This eliminates 11 kernel-doc warnings:
drivers/char/pcmcia/synclink_cs.c:487: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* line discipline callback wrappers
drivers/char/pcmcia/synclink_cs.c:3861: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* called by generic HDLC layer when protocol selected (PPP, frame relay, etc.)
drivers/char/pcmcia/synclink_cs.c:3914: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* called by generic HDLC layer to send frame
drivers/char/pcmcia/synclink_cs.c:3959: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* called by network layer when interface enabled
drivers/char/pcmcia/synclink_cs.c:4022: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* called by network layer when interface is disabled
drivers/char/pcmcia/synclink_cs.c:4053: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* called by network layer to process IOCTL call to network device
drivers/char/pcmcia/synclink_cs.c:4156: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* called by network layer when transmit timeout is detected
drivers/char/pcmcia/synclink_cs.c:4179: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* called by device driver when transmit completes
drivers/char/pcmcia/synclink_cs.c:4191: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* called by device driver when frame received
drivers/char/pcmcia/synclink_cs.c:4231: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* called by device driver when adding device instance
drivers/char/pcmcia/synclink_cs.c:4279: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* called by device driver when removing device instance
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20230114034646.1535-1-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert various parameter names for ->dtr_rts() and related functions
from onoff, on, and raise to active.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230117090358.4796-12-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert the raise/on parameter in ->dtr_rts() to bool through the
callchain. The parameter is used like bool. In USB serial, there
remains a few implicit bool -> larger type conversions because some
devices use u8 in their control messages.
In moxa_tiocmget(), dtr variable was reused for line status which
requires int so use a separate variable for status.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230117090358.4796-8-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Return boolean from ->carrier_raised() instead of 0 and 1. Make the
return type change also to tty_port_carrier_raised() that makes the
->carrier_raised() call (+ cd variable in moxa into which its return
value is stored).
Also cleans up a few unnecessary constructs related to this change:
return xx ? 1 : 0;
-> return xx;
if (xx)
return 1;
return 0;
-> return xx;
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230117090358.4796-7-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patch series "mm/nommu: don't use VM_MAYSHARE for MAP_PRIVATE mappings".
Trying to reduce the confusion around VM_SHARED and VM_MAYSHARE first
requires !CONFIG_MMU to stop using VM_MAYSHARE for MAP_PRIVATE mappings.
CONFIG_MMU only sets VM_MAYSHARE for MAP_SHARED mappings.
This paves the way for further VM_MAYSHARE and VM_SHARED cleanups: for
example, renaming VM_MAYSHARED to VM_MAP_SHARED to make it cleaner what is
actually means.
Let's first get the weird case out of the way and not use VM_MAYSHARE in
MAP_PRIVATE mappings, using a new VM_MAYOVERLAY flag instead.
This patch (of 3):
We want to stop using VM_MAYSHARE in private mappings to pave the way for
clarifying the semantics of VM_MAYSHARE vs. VM_SHARED and reduce the
confusion. While CONFIG_MMU uses VM_MAYSHARE to represent MAP_SHARED,
!CONFIG_MMU also sets VM_MAYSHARE for selected R/O private file mappings
that are an effective overlay of a file mapping.
Let's factor out all relevant VM_MAYSHARE checks in !CONFIG_MMU code into
is_nommu_shared_mapping() first.
Note that whenever VM_SHARED is set, VM_MAYSHARE must be set as well
(unless there is a serious BUG). So there is not need to test for
VM_SHARED manually.
No functional change intended.
Link: https://lkml.kernel.org/r/20230102160856.500584-1-david@redhat.com
Link: https://lkml.kernel.org/r/20230102160856.500584-2-david@redhat.com
Signed-off-by: David Hildenbrand <david@redhat.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: David Hildenbrand <david@redhat.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRTLbB6QfY48x44uB6AXGG7T9hjvgUCY76ohgAKCRCAXGG7T9hj
vo8fAP0XJ94B7asqcN4W3EyeyfqxUf1eZvmWRhrbKqpLnmHLaQEA/uJBkXL49Zj7
TTcbxR1coJ/hPwhtmONU4TNtCZ+RXw0=
=2Ib5
-----END PGP SIGNATURE-----
Merge tag 'for-linus-6.2-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
- two cleanup patches
- a fix of a memory leak in the Xen pvfront driver
- a fix of a locking issue in the Xen hypervisor console driver
* tag 'for-linus-6.2-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/pvcalls: free active map buffer on pvcalls_front_free_map
hvc/xen: lock console list traversal
x86/xen: Remove the unused function p2m_index()
xen: make remove callback of xen driver void returned
TPM 1 is sometimes broken across system suspends, due to races or
locking issues or something else that haven't been diagnosed or fixed
yet, most likely having to do with concurrent reads from the TPM's
hardware random number generator driver. These issues prevent the system
from actually suspending, with errors like:
tpm tpm0: A TPM error (28) occurred continue selftest
...
tpm tpm0: A TPM error (28) occurred attempting get random
...
tpm tpm0: Error (28) sending savestate before suspend
tpm_tis 00:08: PM: __pnp_bus_suspend(): tpm_pm_suspend+0x0/0x80 returns 28
tpm_tis 00:08: PM: dpm_run_callback(): pnp_bus_suspend+0x0/0x10 returns 28
tpm_tis 00:08: PM: failed to suspend: error 28
PM: Some devices failed to suspend, or early wake event detected
This issue was partially fixed by 23393c6461 ("char: tpm: Protect
tpm_pm_suspend with locks"), in a last minute 6.1 commit that Linus took
directly because the TPM maintainers weren't available. However, it
seems like this just addresses the most common cases of the bug, rather
than addressing it entirely. So there are more things to fix still,
apparently.
In lieu of actually fixing the underlying bug, just allow system suspend
to continue, so that laptops still go to sleep fine. Later, this can be
reverted when the real bug is fixed.
Link: https://lore.kernel.org/lkml/7cbe96cf-e0b5-ba63-d1b4-f63d2e826efa@suse.cz/
Cc: stable@vger.kernel.org # 6.1+
Reported-by: Vlastimil Babka <vbabka@suse.cz>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Luigi Semenzato <semenzato@chromium.org>
Cc: Peter Huewe <peterhuewe@gmx.de>
Cc: Jarkko Sakkinen <jarkko@kernel.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Johannes Altmanninger <aclopte@gmail.com>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The <asm/archrandom.h> header is a random.c private detail, not
something to be called by other code. As such, don't make it
automatically available by way of random.h.
Cc: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Here is the set of driver core and kernfs changes for 6.2-rc1.
The "big" change in here is the addition of a new macro,
container_of_const() that will preserve the "const-ness" of a pointer
passed into it.
The "problem" of the current container_of() macro is that if you pass in
a "const *", out of it can comes a non-const pointer unless you
specifically ask for it. For many usages, we want to preserve the
"const" attribute by using the same call. For a specific example, this
series changes the kobj_to_dev() macro to use it, allowing it to be used
no matter what the const value is. This prevents every subsystem from
having to declare 2 different individual macros (i.e.
kobj_const_to_dev() and kobj_to_dev()) and having the compiler enforce
the const value at build time, which having 2 macros would not do
either.
The driver for all of this have been discussions with the Rust kernel
developers as to how to properly mark driver core, and kobject, objects
as being "non-mutable". The changes to the kobject and driver core in
this pull request are the result of that, as there are lots of paths
where kobjects and device pointers are not modified at all, so marking
them as "const" allows the compiler to enforce this.
So, a nice side affect of the Rust development effort has been already
to clean up the driver core code to be more obvious about object rules.
All of this has been bike-shedded in quite a lot of detail on lkml with
different names and implementations resulting in the tiny version we
have in here, much better than my original proposal. Lots of subsystem
maintainers have acked the changes as well.
Other than this change, included in here are smaller stuff like:
- kernfs fixes and updates to handle lock contention better
- vmlinux.lds.h fixes and updates
- sysfs and debugfs documentation updates
- device property updates
All of these have been in the linux-next tree for quite a while with no
problems, OTHER than some merge issues with other trees that should be
obvious when you hit them (block tree deletes a driver that this tree
modifies, iommufd tree modifies code that this tree also touches). If
there are merge problems with these trees, please let me know.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY5wz3A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yks0ACeKYUlVgCsER8eYW+x18szFa2QTXgAn2h/VhZe
1Fp53boFaQkGBjl8mGF8
=v+FB
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the set of driver core and kernfs changes for 6.2-rc1.
The "big" change in here is the addition of a new macro,
container_of_const() that will preserve the "const-ness" of a pointer
passed into it.
The "problem" of the current container_of() macro is that if you pass
in a "const *", out of it can comes a non-const pointer unless you
specifically ask for it. For many usages, we want to preserve the
"const" attribute by using the same call. For a specific example, this
series changes the kobj_to_dev() macro to use it, allowing it to be
used no matter what the const value is. This prevents every subsystem
from having to declare 2 different individual macros (i.e.
kobj_const_to_dev() and kobj_to_dev()) and having the compiler enforce
the const value at build time, which having 2 macros would not do
either.
The driver for all of this have been discussions with the Rust kernel
developers as to how to properly mark driver core, and kobject,
objects as being "non-mutable". The changes to the kobject and driver
core in this pull request are the result of that, as there are lots of
paths where kobjects and device pointers are not modified at all, so
marking them as "const" allows the compiler to enforce this.
So, a nice side affect of the Rust development effort has been already
to clean up the driver core code to be more obvious about object
rules.
All of this has been bike-shedded in quite a lot of detail on lkml
with different names and implementations resulting in the tiny version
we have in here, much better than my original proposal. Lots of
subsystem maintainers have acked the changes as well.
Other than this change, included in here are smaller stuff like:
- kernfs fixes and updates to handle lock contention better
- vmlinux.lds.h fixes and updates
- sysfs and debugfs documentation updates
- device property updates
All of these have been in the linux-next tree for quite a while with
no problems"
* tag 'driver-core-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (58 commits)
device property: Fix documentation for fwnode_get_next_parent()
firmware_loader: fix up to_fw_sysfs() to preserve const
usb.h: take advantage of container_of_const()
device.h: move kobj_to_dev() to use container_of_const()
container_of: add container_of_const() that preserves const-ness of the pointer
driver core: fix up missed drivers/s390/char/hmcdrv_dev.c class.devnode() conversion.
driver core: fix up missed scsi/cxlflash class.devnode() conversion.
driver core: fix up some missing class.devnode() conversions.
driver core: make struct class.devnode() take a const *
driver core: make struct class.dev_uevent() take a const *
cacheinfo: Remove of_node_put() for fw_token
device property: Add a blank line in Kconfig of tests
device property: Rename goto label to be more precise
device property: Move PROPERTY_ENTRY_BOOL() a bit down
device property: Get rid of __PROPERTY_ENTRY_ARRAY_EL*SIZE*()
kernfs: fix all kernel-doc warnings and multiple typos
driver core: pass a const * into of_device_uevent()
kobject: kset_uevent_ops: make name() callback take a const *
kobject: kset_uevent_ops: make filter() callback take a const *
kobject: make kobject_namespace take a const *
...
Alexander Sverdlin