Set the GPMI CTRL1 GANGED_RDYBUSY bit so driver can sense the R/B signal
from all CS.
For the NAND chip MT29F64G08AFAAAWP, only the first chip detected
without the patch.
[ 3.764118] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0x68
[ 3.770613] nand: Micron MT29F64G08AFAAAWP
[ 3.774752] nand: 4096 MiB, SLC, erase size: 1024 KiB, page size: 8192, OOB size: 448
[ 3.786421] Bad block table found at page 524160, version 0x01
[ 3.792730] Bad block table found at page 524032, version 0x01
After applying the patch
[ 3.764445] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0x68
[ 3.770941] nand: Micron MT29F64G08AFAAAWP
[ 3.775080] nand: 4096 MiB, SLC, erase size: 1024 KiB, page size: 8192, OOB size: 448
[ 3.784390] nand: 2 chips detected
[ 3.790900] Bad block table found at page 524160, version 0x01
[ 3.796776] Bad block table found at page 1048448, version 0x01
Signed-off-by: Han Xu <han.xu@nxp.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201209035104.22679-2-han.xu@nxp.com
SDX55 uses QPIC version 2.0.0 IP for the NAND controller support.
In this version, DEV_CMD_* registers are moved to operational state,
hence CPU access in BAM mode is restricted. So, skip accessing these
registers and also use a different config for reading ONFI parameters.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201126085705.48399-3-manivannan.sadhasivam@linaro.org
Call clk_disable_unprepare(nfc->phase_rx) if the clk_set_rate() function
fails to avoid a resource leak.
Fixes: 8fae856c53 ("mtd: rawnand: meson: add support for Amlogic NAND flash controller")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/X8ikVCnUsfTpffFB@mwanda
The retrieval of driver data via of_device_get_match_data() can make
the code simpler.
Use of_device_get_match_data() to simplify the code.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201126030946.2058-1-festevam@gmail.com
This patch adds the new IP of Nand Flash Controller(NFC) support
on Intel's Lightning Mountain(LGM) SoC.
DMA is used for burst data transfer operation, also DMA HW supports
aligned 32bit memory address and aligned data access by default.
DMA burst of 8 supported. Data register used to support the read/write
operation from/to device.
Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201110012333.18647-3-vadivel.muruganx.ramuthevar@linux.intel.com
pm_runtime_get_sync() will increment pm usage at first and it
will resume the device later. If runtime of the device has
error or device is in inaccessible state(or other error state),
resume operation will fail. If we do not call put operation to
decrease the reference, it will result in reference leak in
the two functions(gpmi_init and gpmi_nfc_exec_op). Moreover,
this device cannot enter the idle state and always stay busy or
other non-idle state later. So we fixed it through adding
pm_runtime_put_noidle.
Fixes: 5bc6bb603b ("mtd: rawnand: gpmi: Fix suspend/resume problem")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201107110552.1568742-1-zhangqilong3@huawei.com
If an error happens in mtd_device_parse_register or mtd_device_register,
memory allocated for struct platram_info is leaked.
Make platram_probe() call platram_remove() on all error paths
after struct platram_info allocation to correctly free resources.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Baskov Evgeiny <baskov@ispras.ru>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201113160537.899-1-baskov@ispras.ru
struct mtd_info has a flag oops_panic_write which is set when the write
operation is issued via the panic_write() callback. That allows controller
drivers to distinguish the panic write from a regular write.
Replace the open coded 'in_interrupt() | oops_in_progress' checks with a
check for that flag. in_interrupt() is an unrealiable indicator anyway as
it covers all sorts of atomic contexts not only hard and soft interrupt
service routines.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Tudor Ambarus <tudor.ambarus@microchip.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Boris Brezillon <boris.brezillon@collabora.com>
Cc: linux-mtd@lists.infradead.org
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201113141422.2214771-1-bigeasy@linutronix.de
While working a bit on this driver I dropped the platform includes and
commented a few lines just to verify the correctness of my changes. It
appeared the following:
drivers/mtd/nand/raw/au1550nd.c: In function ‘au1550nd_waitrdy’:
drivers/mtd/nand/raw/au1550nd.c:130:3: error: implicit declaration of function ‘usleep_range’ [-Werror=implicit-function-declaration]
usleep_range(10, 100);
^~~~~~~~~~~~
drivers/mtd/nand/raw/au1550nd.c: In function ‘au1550nd_exec_instr’:
drivers/mtd/nand/raw/au1550nd.c:188:3: error: implicit declaration of function ‘ndelay’ [-Werror=implicit-function-declaration]
ndelay(instr->delay_ns);
^~~~~~
I think the delay.h header should be included in this file and not
come from one of its platform includes, so let's add it here.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201113124021.32675-1-miquel.raynal@bootlin.com
The NAND ECC core is included in the generic NAND core when it is
compiled in.
Different software ECC engines drivers will select the NAND ECC core
and thus also have a dependency on the NAND core. Using a "depends on"
between the two leads to possible cases (not real cases, but created
by robots) where one is still unselected because of the "select does
not verifies depends on" game:
WARNING: unmet direct dependencies detected for MTD_NAND_ECC
Depends on [n]: MTD [=m] && MTD_NAND_CORE [=n]
Selected by [m]:
- MTD_NAND_ECC_SW_HAMMING [=y] && MTD [=m]
- MTD_NAND_ECC_SW_BCH [=y] && MTD [=m]
Fix this by using a select instead.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Link: https://lore.kernel.org/linux-mtd/20201113123945.32592-1-miquel.raynal@bootlin.com
i.MX is a devicetree-only platform now and the existing platform data
support in this driver was only useful for old non-devicetree platforms.
Get rid of the platform data support since it is no longer used.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201110121908.19400-1-festevam@gmail.com
of_find_device_by_node() already takes a reference to the device, and
ingenic_ecc_release() will drop the reference. So, the get_device() in
ingenic_ecc_get() is redundand.
Fixes: 15de8c6efd0e("mtd: rawnand: ingenic: Separate top-level and SoC specific code")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201031105439.2304211-1-yukuai3@huawei.com
This code has been written in 2008 and is fine, but in order to keep
robots happy, I think it's time to change a little bit this code just
to clarify the different possible values of eccsize_mult. Indeed, this
variable may only take the value 1 or 2 because step_size, in the case
of the software Hamming ECC engine may only be 256 or 512. Depending
on the value of eccsize_mult, an extra rp17 variable is set, or not
and triggers the following warning:
smatch warnings:
ecc_sw_hamming_calculate() error: uninitialized symbol 'rp17'.
As highlighted by Dan Carpenter, if the only possible values for
eccsize_mult are 1 and 2, then the code is fine, but "it's hard to
tell just from looking".
So instead of shifting step_size, let's use a ternary condition to
assign to eccsize_mult the only two possible values and clarify the
driver's logic.
Now that the situation is clarified for humans, ensure rp17 is
initialized to 0 to keep compilers and robots silent as well.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201030172333.28390-1-miquel.raynal@bootlin.com
This patch enables NAND MDMA (MBUS DMA) mode for
the Allwinner SoCs A23/A33/H3.
The DMA transfer method gets sets now to MBUS DMA as default for
the sun8i-a23-nand-controller (till now DMA transfer was executed
via the shared DMA engine).
The main advantage is more bandwidth for the users of the shared DMA
engine and also that the MBUS DMA setup requires less configuration
effort. For example you don't need to define a dedicated DMA channel
in the device-tree any more.
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Manuel Dipolt <manuel.dipolt@robart.cc>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/154840787.280672.1602517282173.JavaMail.zimbra@robart.cc
After each codeword NAND_FLASH_STATUS is read for possible operational
failures. But there is no DMA sync for CPU operation before reading it
and this leads to incorrect or older copy of DMA buffer in reg_read_buf.
This patch adds the DMA sync on reg_read_buf for CPU before reading it.
Fixes: 5bc36b2bf6 ("mtd: rawnand: qcom: check for operation errors in case of raw read")
Cc: stable@vger.kernel.org
Signed-off-by: Praveenkumar I <ipkumar@codeaurora.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1602230872-25616-1-git-send-email-ipkumar@codeaurora.org
Even if this is not supposed to happen, there is no reason to fail the
probe if it was explicitly requested to use no ECC engine at all (for
instance, during development). This condition is met by just
commenting out the error on the OOB free bytes count after the
assignation of an ECC engine if none was provided (any other situation
would error out much earlier anyway).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201001102014.20100-5-miquel.raynal@bootlin.com
Now that all the logic is available in the NAND core, let's use it
from the SPI-NAND core. Right now there is no functional change as the
default ECC engine for SPI-NANDs is set to 'on-die', but user can now
use software correction if they want to by just setting the right
properties in the DT.
Also note that the OOB layout handling is removed from the SPI-NAND
core as each ECC engine is supposed to handle it by it's own; users
should not be aware of that.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201001102014.20100-4-miquel.raynal@bootlin.com
Add the logic in the NAND core to find the right ECC engine depending
on the NAND chip requirements and the user desires. Right now, the
choice may be made between (more will come):
* software Hamming
* software BCH
* on-die (SPI-NAND devices only)
Once the ECC engine has been found, the ECC engine must be
configured.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201001102014.20100-2-miquel.raynal@bootlin.com
The SPI-NAND layer default is on-die ECC because until now it was the
only one supported. New SPI-NAND chip flavors might use something else
as ECC engine provider but this will always be the default if the user
does not choose explicitly something else.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200930154109.3922-6-miquel.raynal@bootlin.com
Make use of the existing functions taken from the SPI-NAND core to
instantiate an on-die ECC engine specific to the SPI-NAND core. The
next step will be to tweak the core to use this object instead of
calling the helpers directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200930154109.3922-4-miquel.raynal@bootlin.com
Prepare the creation of a SPI-NAND on-die ECC engine by gathering the
ECC-related code earlier enough in the core to avoid the need for
forward declarations.
The next step is to actually create that engine by implementing the
generic ECC interface.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200930154109.3922-3-miquel.raynal@bootlin.com
This code is meant to be reused by the SPI-NAND core. Now that the
driver has been cleaned and reorganized, use a generic ECC engine
object to store the driver's data instead of accessing members of the
nand_chip structure. This means adding proper init/cleanup helpers.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200929230124.31491-17-miquel.raynal@bootlin.com
Prefix by ecc_sw_hamming_ the functions which should be internal only
but are exported for "raw" operations.
Prefix by nand_ecc_sw_hamming_ the other functions which will be used
in the context of the declaration of an Hamming proper ECC engine
object.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200929230124.31491-16-miquel.raynal@bootlin.com
Some functions should never have been exported (the ones prefixed by
__*), in this case simply drop the documentation, we never want
anybody to use this function from the outside.
For the other functions, enhance the style.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200929230124.31491-14-miquel.raynal@bootlin.com
The include file pretends being the header for "ECC algorithm", while
it is just the header for the Hamming implementation. Make this clear
by rewording the sentence.
Do the same with the module description.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200929230124.31491-13-miquel.raynal@bootlin.com
nand_ecc_ctrl embeds a private pointer which only has a meaning in the
sunxi driver. This structure will soon be deprecated, but as this
field is actually not needed, let's just drop it.
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20200929230124.31491-11-miquel.raynal@bootlin.com
Let's continue introducing the generic ECC engine abstraction in the
NAND subsystem by instantiating a first ECC engine: the software
BCH one.
While at it, make a very tidy ecc_sw_bch_init() function and move all
the sanity checks and user input management in
nand_ecc_sw_bch_init_ctx(). This second helper will be called from the
raw RAND core.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200929230124.31491-10-miquel.raynal@bootlin.com
Traditionally, Linux unlocks the whole flash because there are legacy
devices which has the write protection bits set by default at startup.
If you actually want to use the flash protection bits, eg. because there
is a read-only part for a bootloader, this automatic unlocking is
harmful. If there is no hardware write protection in place (usually
called WP#), a startup of the kernel just discards this protection.
I've gone through the datasheets of all the flashes (except the Intel
ones where I could not find any datasheet nor reference) which supports
the unlocking feature and looked how the sector protection was
implemented. The currently supported flashes can be divided into the
following two categories:
(1) block protection bits are non-volatile. Thus they keep their values
at reset and power-cycle
(2) flashes where these bits are volatile. After reset or power-cycle,
the whole memory array is protected.
(a) some devices needs a special "Global Unprotect" command, eg.
the Atmel AT25DF041A.
(b) some devices require to clear the BPn bits in the status
register.
Due to the reasons above, we do not want to clear the bits for flashes
which belong to category (1). Fortunately for us, only Atmel flashes
fall into category (2a). Implement the "Global Protect" and "Global
Unprotect" commands for these. For (2b) we can use normal block
protection locking scheme.
This patch adds a new flag to indicate the case (2). Only if we have
such a flash we unlock the whole flash array. To be backwards compatible
it also introduces a kernel configuration option which restores the
complete legacy behavior ("Disable write protection on any flashes").
Hopefully, this will clean up "unlock the entire flash for legacy
devices" once and for all.
For reference here are the actually commits which introduced the legacy
behavior (and extended the behavior to other chip manufacturers):
commit f80e521c91 ("mtd: m25p80: add support for the Intel/Numonyx {16,32,64}0S33B SPI flash chips")
commit ea60658a08 ("mtd: m25p80: disable SST software protection bits by default")
commit 7228982442 ("[MTD] m25p80: fix bug - ATmel spi flash fails to be copied to")
Actually, this might also fix handling of the Atmel AT25DF flashes,
because the original commit 7228982442 ("[MTD] m25p80: fix bug -
ATmel spi flash fails to be copied to") was writing a 0 to the status
register, which is a "Global Unprotect". This might not be the case in
the current code which only handles the block protection bits BP2, BP1
and BP0. Thus, it depends on the current contents of the status register
if this unlock actually corresponds to a "Global Unprotect" command. In
the worst case, the current code might leave the AT25DF flashes in a
write protected state.
The commit 191f5c2ed4 ("mtd: spi-nor: use 16-bit WRR command when QE
is set on spansion flashes") changed that behavior by just clearing BP2
to BP0 instead of writing a 0 to the status register.
Further, the commit 3e0930f109 ("mtd: spi-nor: Rework the disabling
of block write protection") expanded the unlock_all() feature to ANY
flash which supports locking.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201203162959.29589-8-michael@walle.cc
These flashes have some weird BP bits mapping which aren't supported in
the current locking code. Just add a simple unlock op to unprotect the
entire flash array which is needed for legacy behavior.
Fixes: 3e0930f109 ("mtd: spi-nor: Rework the disabling of block write protection")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201203162959.29589-7-michael@walle.cc
For the Atmel and SST parts this flag was already moved to individual
flash parts because it is considered bad esp. because newer flash chips
will automatically inherit the "has locking" support. While this won't
likely be the case for the Intel parts, we do it for consistency
reasons.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201203162959.29589-6-michael@walle.cc
This is considered bad for the following reasons:
(1) We only support the block protection with BPn bits for write
protection. Not all SST parts support this.
(2) Newly added flash chip will automatically inherit the "has
locking" support and thus needs to explicitly tested. Better
be opt-in instead of opt-out.
(3) There are already supported flashes which doesn't support
the locking scheme. So I assume this wasn't properly tested
before adding that chip; which enforces my previous argument
that locking support should be an opt-in.
Remove the global flag and add individual flags to all flashes
which supports BP locking. In particular the following flashes
don't support the BP scheme:
- SST26VF016B
- SST26WF016B
- SST26VF064B
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201203162959.29589-5-michael@walle.cc
This is considered bad for the following reasons:
(1) We only support the block protection with BPn bits for write
protection. Not all Atmel parts support this.
(2) Newly added flash chip will automatically inherit the "has
locking" support and thus needs to explicitly tested. Better
be opt-in instead of opt-out.
(3) There are already supported flashes which doesn't support
the locking scheme. So I assume this wasn't properly tested
before adding that chip; which enforces my previous argument
that locking support should be an opt-in.
Remove the global flag and add individual flags to all flashes which
supports BP locking. In particular the following flashes don't support
the BP scheme:
- AT26F004
- AT25SL321
- AT45DB081D
Please note, that some flashes which are marked as SPI_NOR_HAS_LOCK just
support Global Protection, i.e. not our supported block protection
locking scheme. This is to keep backwards compatibility with the
current "unlock all at boot" mechanism. In particular the following
flashes doesn't have BP bits:
- AT25DF041A
- AT25DF321
- AT25DF321A
- AT25DF641
- AT26DF081A
- AT26DF161A
- AT26DF321
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201203162959.29589-4-michael@walle.cc
Just try to unlock the whole SPI-NOR flash array. Don't abort the
probing in case of an error. Justifications:
(1) For some boards, this just works because
spi_nor_write_16bit_sr_and_check() is broken and just checks the
second half of the 16bit. Once that will be fixed, SPI probe will
fail for boards which has hardware-write protected SPI-NOR flashes.
(2) Until now, hardware write-protection was the only viable solution
to use the block protection bits. This is because this very
function spi_nor_unlock_all() will be called unconditionally on
every linux boot. Therefore, this bits only makes sense in
combination with the hardware write-protection. If we would fail
the SPI probe on an error in spi_nor_unlock_all() we'd break
virtually all users of the block protection bits.
(3) We should try hard to keep the MTD working even if the flash might
not be writable/erasable.
Fixes: 3e0930f109 ("mtd: spi-nor: Rework the disabling of block write protection")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201203162959.29589-3-michael@walle.cc
This flash part actually has 4 block protection bits.
Please note, that this patch is just based on information of the
datasheet of the datasheet and wasn't tested.
Fixes: 3e0930f109 ("mtd: spi-nor: Rework the disabling of block write protection")
Reported-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201203162959.29589-2-michael@walle.cc
The S28 flash family uses 2-bit ECC by default with each ECC block being
16 bytes. Under this scheme multi-pass programming to an ECC block is
not allowed. Set the writesize to make sure multi-pass programming is
not attempted on the flash.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201201102711.8727-4-p.yadav@ti.com
Some flashes like the Cypress S28 family use ECC. Under this ECC scheme,
multi-pass writes to an ECC block is not allowed. In other words, once
data is programmed to an ECC block, it can't be programmed again without
erasing it first.
Upper layers like file systems need to be given this information so they
do not cause error conditions on the flash by attempting multi-pass
programming. This can be done by setting 'writesize' in 'struct
mtd_info'.
Set the default to 1 but allow flashes to modify it in fixup hooks. If
more flashes show up with this constraint in the future it might be
worth it to add it to 'struct flash_info', but for now increasing its
size is not worth it.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201201102711.8727-3-p.yadav@ti.com
There are a few typos in comments in the SPI NOR framework; fix them.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201130152416.1283972-1-j.neuschaefer@gmx.net
Permit the user to specify the erase page size as a parameter.
This solves two problems:
- phram can access images made by mkfs.jffs2. mkfs.jffs2 won't
create images with erase sizes less than 8KiB; many architectures
define PAGE_SIZE as 4KiB.
- Allows more effective use of small capacity devices. JFFS2
needs somewhere between 2 and 5 empty pages for garbage collection;
and for an NVRAM part with only 32KiB of space, a smaller erase page
allows much better utilization in applications where garbage collection
is important.
Signed-off-by: Patrick O'Grady <patrick@baymotion.com>
Reviewed-by: Joern Engel <joern@logfs.org>
Link: https://lore.kernel.org/lkml/CAJ7m5OqYv_=JB9NhHsqBsa8YU0DFRoP7C+W10PY22wonAGJK=A@mail.gmail.com/
[Guohua Zhong: fix token array index out of bounds and update patch for kernel master branch]
Signed-off-by: Guohua Zhong <zhongguohua1@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201207095529.20896-1-zhongguohua1@huawei.com
sparse is unhappy with us casting the __iomem address space pointer to
a type with no address space attribute specified:
"sparse warnings: (new ones prefixed by >>)"
>> drivers/mtd/maps/physmap-bt1-rom.c:78:18: sparse: sparse: cast removes address space '__iomem' of expression
Indeed we perform the __iomem-less type casting but to an integer
variable. The integer variable isn't dereferenced then, so the casting is
safe and won't cause any problem. But in order to make sparse happy and
keep the code coherent let's fix the warning by converting the local
"shift" and "chunk" variables to the "unsigned int" type (since their
value won't ever exceed three) and cast the __iomem-pointers to uintptr_t.
Add the same fix to the bt1_rom_map_read() method for unification.
Fixes: b3e79e7682 ("mtd: physmap: Add Baikal-T1 physically mapped ROM support")
Link: https://lore.kernel.org/lkml/202011021254.XC70BaQT-lkp@intel.com/
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Pavel Parkhomenko <Pavel.Parkhomenko@baikalelectronics.ru>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201125072640.23516-1-Sergey.Semin@baikalelectronics.ru
Some devices (especially QCA ones) are already using hardcoded partition
names with colons in it. The OpenMesh A62 for example provides following
mtd relevant information via cmdline:
root=31:11 mtdparts=spi0.0:256k(0:SBL1),128k(0:MIBIB),384k(0:QSEE),64k(0:CDT),64k(0:DDRPARAMS),64k(0:APPSBLENV),512k(0:APPSBL),64k(0:ART),64k(custom),64k(0:KEYS),0x002b0000(kernel),0x00c80000(rootfs),15552k(inactive) rootfsname=rootfs rootwait
The change to split only on the last colon between mtd-id and partitions
will cause newpart to see following string for the first partition:
KEYS),0x002b0000(kernel),0x00c80000(rootfs),15552k(inactive)
Such a partition list cannot be parsed and thus the device fails to boot.
Avoid this behavior by making sure that the start of the first part-name
("(") will also be the last byte the mtd-id split algorithm is using for
its colon search.
Fixes: eb13fa0227 ("mtd: parser: cmdline: Support MTD names containing one or more colons")
Cc: stable@vger.kernel.org
Cc: Ron Minnich <rminnich@google.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201124062506.185392-1-sven@narfation.org
Switch the block device lookup interfaces to directly work with a dev_t
so that struct block_device references are only acquired by the
blkdev_get variants (and the blk-cgroup special case). This means that
we now don't need an extra reference in the inode and can generally
simplify handling of struct block_device to keep the lookups contained
in the core block layer code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Coly Li <colyli@suse.de> [bcache]
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This code is meant to be reused by the SPI-NAND core. Now that the
driver has been cleaned and reorganized, use a generic ECC engine
object to store the driver's data instead of accessing members of the
nand_chip structure.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200929230124.31491-9-miquel.raynal@bootlin.com
These functions must be usable by the main NAND core, so their names
must be technology-agnostic as well as the parameters. Hence, we pass
a generic nand_device instead of a raw nand_chip structure.
As it seems that changing the raw NAND functions to always pass a
generic NAND device is a lost of time, we prefer to create dedicated
raw NAND wrappers that will be useful in the near future to do the
translation.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200929230124.31491-8-miquel.raynal@bootlin.com
The NAND BCH control structure has nothing to do outside of this
driver, all users of the nand_bch_init/free() functions just save it
to chip->ecc.priv so do it in this driver directly and return a
regular error code instead.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200929230124.31491-5-miquel.raynal@bootlin.com
Currently, BCH and Hamming engine are sharing the same
tweaking/restoring I/O mechanism: they need the I/O request to fully
cover the main/OOB area. Let's make this code generic as sharing the
code between two drivers is already a win. Maybe other ECC engine
drivers will need it too.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200929230124.31491-2-miquel.raynal@bootlin.com
Fixes the following W=1 kernel build warning(s):
drivers/mtd/devices/powernv_flash.c:129: warning: Cannot understand * @mtd: the device
drivers/mtd/devices/powernv_flash.c:145: warning: Cannot understand * @mtd: the device
drivers/mtd/devices/powernv_flash.c:161: warning: Cannot understand * @mtd: the device
drivers/mtd/devices/powernv_flash.c:184: warning: Function parameter or member 'dev' not described in 'powernv_flash_set_driver_info'
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linux-mtd@lists.infradead.org
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201109182206.3037326-24-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/mtd/nand/onenand/onenand_base.c:140: warning: Function parameter or member 'mtd' not described in 'onenand_ooblayout_32_64_ecc'
drivers/mtd/nand/onenand/onenand_base.c:140: warning: Function parameter or member 'section' not described in 'onenand_ooblayout_32_64_ecc'
drivers/mtd/nand/onenand/onenand_base.c:140: warning: Function parameter or member 'oobregion' not described in 'onenand_ooblayout_32_64_ecc'
drivers/mtd/nand/onenand/onenand_base.c:1436: warning: bad line:
drivers/mtd/nand/onenand/onenand_base.c:1971: warning: Function parameter or member 'ops' not described in 'onenand_write_oob_nolock'
drivers/mtd/nand/onenand/onenand_base.c:1971: warning: Excess function parameter 'len' description in 'onenand_write_oob_nolock'
drivers/mtd/nand/onenand/onenand_base.c:1971: warning: Excess function parameter 'retlen' description in 'onenand_write_oob_nolock'
drivers/mtd/nand/onenand/onenand_base.c:1971: warning: Excess function parameter 'buf' description in 'onenand_write_oob_nolock'
drivers/mtd/nand/onenand/onenand_base.c:1971: warning: Excess function parameter 'mode' description in 'onenand_write_oob_nolock'
drivers/mtd/nand/onenand/onenand_base.c:2156: warning: Function parameter or member 'block_size' not described in 'onenand_multiblock_erase'
drivers/mtd/nand/onenand/onenand_base.c:2156: warning: Excess function parameter 'region' description in 'onenand_multiblock_erase'
drivers/mtd/nand/onenand/onenand_base.c:2771: warning: Function parameter or member 'ops' not described in 'onenand_otp_write_oob_nolock'
drivers/mtd/nand/onenand/onenand_base.c:2771: warning: Excess function parameter 'len' description in 'onenand_otp_write_oob_nolock'
drivers/mtd/nand/onenand/onenand_base.c:2771: warning: Excess function parameter 'retlen' description in 'onenand_otp_write_oob_nolock'
drivers/mtd/nand/onenand/onenand_base.c:2771: warning: Excess function parameter 'buf' description in 'onenand_otp_write_oob_nolock'
drivers/mtd/nand/onenand/onenand_base.c:3387: warning: Function parameter or member 'mtd' not described in 'flexonenand_get_boundary'
drivers/mtd/nand/onenand/onenand_base.c:3387: warning: Excess function parameter 'onenand_info' description in 'flexonenand_get_boundary'
drivers/mtd/nand/onenand/onenand_base.c:3509: warning: Function parameter or member 'mtd' not described in 'flexonenand_check_blocks_erased'
drivers/mtd/nand/onenand/onenand_base.c:3509: warning: Excess function parameter 'mtd_info' description in 'flexonenand_check_blocks_erased'
drivers/mtd/nand/onenand/onenand_base.c:3557: warning: Function parameter or member 'die' not described in 'flexonenand_set_boundary'
drivers/mtd/nand/onenand/onenand_base.c:3557: warning: Function parameter or member 'boundary' not described in 'flexonenand_set_boundary'
drivers/mtd/nand/onenand/onenand_base.c:3557: warning: Function parameter or member 'lock' not described in 'flexonenand_set_boundary'
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201109182206.3037326-23-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/mtd/nand/raw/arasan-nand-controller.c:133: warning: Function parameter or member 'buf' not described in 'anfc_op'
Cc: Naga Sureshkumar Relli <nagasure@xilinx.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Choudary Kalluri <punnaia@xilinx.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201109182206.3037326-22-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/mtd/nand/raw/sunxi_nand.c:250: warning: Function parameter or member 'caps' not described in 'sunxi_nfc'
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Boris BREZILLON <b.brezillon.dev@gmail.com>
Cc: Qiang Yu <yuq825@gmail.com>
Cc: Dmitriy B <rzk333@gmail.com>
Cc: Sergey Lapin <slapin@ossfans.org>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201109182206.3037326-21-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/mtd/nand/raw/omap2.c:191: warning: Function parameter or member 'info' not described in 'omap_prefetch_enable'
drivers/mtd/nand/raw/omap2.c:221: warning: Function parameter or member 'cs' not described in 'omap_prefetch_reset'
drivers/mtd/nand/raw/omap2.c:221: warning: Function parameter or member 'info' not described in 'omap_prefetch_reset'
drivers/mtd/nand/raw/omap2.c:946: warning: Function parameter or member 'chip' not described in 'omap_enable_hwecc'
drivers/mtd/nand/raw/omap2.c:946: warning: Excess function parameter 'mtd' description in 'omap_enable_hwecc'
drivers/mtd/nand/raw/omap2.c:1017: warning: Function parameter or member 'chip' not described in 'omap_dev_ready'
drivers/mtd/nand/raw/omap2.c:1017: warning: Excess function parameter 'mtd' description in 'omap_dev_ready'
drivers/mtd/nand/raw/omap2.c:1036: warning: Function parameter or member 'chip' not described in 'omap_enable_hwecc_bch'
drivers/mtd/nand/raw/omap2.c:1036: warning: Excess function parameter 'mtd' description in 'omap_enable_hwecc_bch'
drivers/mtd/nand/raw/omap2.c:1142: warning: Function parameter or member 'ecc_calc' not described in '_omap_calculate_ecc_bch'
drivers/mtd/nand/raw/omap2.c:1142: warning: Excess function parameter 'ecc_code' description in '_omap_calculate_ecc_bch'
drivers/mtd/nand/raw/omap2.c:1270: warning: Function parameter or member 'ecc_calc' not described in 'omap_calculate_ecc_bch_sw'
drivers/mtd/nand/raw/omap2.c:1270: warning: Excess function parameter 'ecc_code' description in 'omap_calculate_ecc_bch_sw'
drivers/mtd/nand/raw/omap2.c:1284: warning: Function parameter or member 'ecc_calc' not described in 'omap_calculate_ecc_bch_multi'
drivers/mtd/nand/raw/omap2.c:1284: warning: Excess function parameter 'ecc_code' description in 'omap_calculate_ecc_bch_multi'
drivers/mtd/nand/raw/omap2.c:1681: warning: Function parameter or member 'info' not described in 'is_elm_present'
drivers/mtd/nand/raw/omap2.c:1681: warning: Function parameter or member 'elm_node' not described in 'is_elm_present'
drivers/mtd/nand/raw/omap2.c:1681: warning: Excess function parameter 'omap_nand_info' description in 'is_elm_present'
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Jian Zhang <jzhang@ti.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201109182206.3037326-20-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/mtd/nand/raw/omap_elm.c:102: warning: Function parameter or member 'ecc_steps' not described in 'elm_config'
drivers/mtd/nand/raw/omap_elm.c:102: warning: Function parameter or member 'ecc_step_size' not described in 'elm_config'
drivers/mtd/nand/raw/omap_elm.c:102: warning: Function parameter or member 'ecc_syndrome_size' not described in 'elm_config'
drivers/mtd/nand/raw/omap_elm.c:440: warning: Function parameter or member 'info' not described in 'elm_context_save'
drivers/mtd/nand/raw/omap_elm.c:488: warning: Function parameter or member 'info' not described in 'elm_context_restore'
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201109182206.3037326-19-lee.jones@linaro.org
Correct 'controller' typo while we're at it.
Fixes the following W=1 kernel build warning(s):
drivers/mtd/nand/raw/s3c2410.c:172: warning: Function parameter or member 'controller' not described in 's3c2410_nand_info'
drivers/mtd/nand/raw/s3c2410.c:172: warning: Function parameter or member 'freq_transition' not described in 's3c2410_nand_info'
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Ben Dooks <ben@simtec.co.uk>
Cc: linux-mtd@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201109182206.3037326-18-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/mtd/nand/raw/cafe_nand.c:372: warning: Function parameter or member 'page' not described in 'cafe_nand_read_page'
drivers/mtd/nand/raw/cafe_nand.c:372: warning: Excess function parameter 'mtd' description in 'cafe_nand_read_page'
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Boris Brezillon <boris.brezillon@collabora.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201109182206.3037326-17-lee.jones@linaro.org
'dummy' is never checked (as per the nomenclature) and the use of
'emtpymatch' is currently #if 0'ed out. We could also #if 0 the
declaration, but #ifery is pretty ugly, so I like to keep it to a
minimum.
Fixes the following W=1 kernel build warning(s):
drivers/mtd/nand/raw/diskonchip.c: In function ‘DoC_Delay’:
drivers/mtd/nand/raw/diskonchip.c:219:16: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable]
drivers/mtd/nand/raw/diskonchip.c: In function ‘doc200x_calculate_ecc’:
drivers/mtd/nand/raw/diskonchip.c:706:6: warning: variable ‘emptymatch’ set but not used [-Wunused-but-set-variable]
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Boris Brezillon <boris.brezillon@collabora.com>
Cc: Dan Brown <dan_brown@ieee.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201109182206.3037326-16-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/mtd/ubi/gluebi.c:446: warning: Function parameter or member 'ns_ptr' not described in 'gluebi_notify'
drivers/mtd/ubi/gluebi.c:446: warning: Excess function parameter 'ptr' description in 'gluebi_notify'
Cc: Richard Weinberger <richard@nod.at>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201109182206.3037326-15-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1854: warning: Function parameter or member 'host' not described in 'brcmnand_edu_trans'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1854: warning: Function parameter or member 'addr' not described in 'brcmnand_edu_trans'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1854: warning: Function parameter or member 'buf' not described in 'brcmnand_edu_trans'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1854: warning: Function parameter or member 'len' not described in 'brcmnand_edu_trans'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1854: warning: Function parameter or member 'cmd' not described in 'brcmnand_edu_trans'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1951: warning: Function parameter or member 'host' not described in 'brcmnand_fill_dma_desc'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1951: warning: Function parameter or member 'desc' not described in 'brcmnand_fill_dma_desc'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1951: warning: Function parameter or member 'addr' not described in 'brcmnand_fill_dma_desc'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1951: warning: Function parameter or member 'buf' not described in 'brcmnand_fill_dma_desc'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1951: warning: Function parameter or member 'len' not described in 'brcmnand_fill_dma_desc'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1951: warning: Function parameter or member 'dma_cmd' not described in 'brcmnand_fill_dma_desc'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1951: warning: Function parameter or member 'begin' not described in 'brcmnand_fill_dma_desc'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1951: warning: Function parameter or member 'end' not described in 'brcmnand_fill_dma_desc'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1951: warning: Function parameter or member 'next_desc' not described in 'brcmnand_fill_dma_desc'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1977: warning: Function parameter or member 'host' not described in 'brcmnand_dma_run'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1977: warning: Function parameter or member 'desc' not described in 'brcmnand_dma_run'
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Kamal Dasu <kdasu.kdev@gmail.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Cc: bcm-kernel-feedback-list@broadcom.com
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201109182206.3037326-14-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/mtd/ubi/wl.c:584: warning: Function parameter or member 'nested' not described in 'schedule_erase'
drivers/mtd/ubi/wl.c:1075: warning: Excess function parameter 'shutdown' description in '__erase_worker'
Cc: Richard Weinberger <richard@nod.at>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201109182206.3037326-13-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/mtd/ubi/eba.c:1304: warning: Function parameter or member 'vidb' not described in 'ubi_eba_copy_leb'
drivers/mtd/ubi/eba.c:1304: warning: Excess function parameter 'vid_hdr' description in 'ubi_eba_copy_leb'
drivers/mtd/ubi/eba.c:1483: warning: Function parameter or member 'ai' not described in 'print_rsvd_warning'
Cc: Richard Weinberger <richard@nod.at>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201109182206.3037326-12-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/mtd/ubi/kapi.c:464: warning: Function parameter or member 'sgl' not described in 'ubi_leb_read_sg'
drivers/mtd/ubi/kapi.c:464: warning: Excess function parameter 'buf' description in 'ubi_leb_read_sg'
Cc: Richard Weinberger <richard@nod.at>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201109182206.3037326-11-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/mtd/nand/spi/toshiba.c:36: warning: Function parameter or member 'write_cache_variants' not described in 'SPINAND_OP_VARIANTS'
drivers/mtd/nand/spi/toshiba.c:36: warning: Function parameter or member '0' not described in 'SPINAND_OP_VARIANTS'
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Yoshio Furuyama <ytc-mb-yfuruyama7@kioxia.com>
Cc: Frieder Schrempf <frieder.schrempf@kontron.de>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201109182206.3037326-10-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/mtd/ubi/build.c:61: warning: Function parameter or member 'ubi_num' not described in 'mtd_dev_param'
Cc: Richard Weinberger <richard@nod.at>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201109182206.3037326-9-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/mtd/spi-nor/controllers/hisi-sfc.c:328: warning: Function parameter or member 'np' not described in 'hisi_spi_nor_register'
drivers/mtd/spi-nor/controllers/hisi-sfc.c:328: warning: Function parameter or member 'host' not described in 'hisi_spi_nor_register'
Cc: Tudor Ambarus <tudor.ambarus@microchip.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: linux-mtd@lists.infradead.org
Cc: linux-media@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: linaro-mm-sig@lists.linaro.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201109182206.3037326-8-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/mtd/nand/onenand/onenand_bbt.c:33: warning: Function parameter or member 'buf' not described in 'check_short_pattern'
drivers/mtd/nand/onenand/onenand_bbt.c:33: warning: Function parameter or member 'len' not described in 'check_short_pattern'
drivers/mtd/nand/onenand/onenand_bbt.c:33: warning: Function parameter or member 'paglen' not described in 'check_short_pattern'
drivers/mtd/nand/onenand/onenand_bbt.c:33: warning: Function parameter or member 'td' not described in 'check_short_pattern'
drivers/mtd/nand/onenand/onenand_bbt.c:57: warning: Function parameter or member 'mtd' not described in 'create_bbt'
drivers/mtd/nand/onenand/onenand_bbt.c:57: warning: Function parameter or member 'buf' not described in 'create_bbt'
drivers/mtd/nand/onenand/onenand_bbt.c:57: warning: Function parameter or member 'bd' not described in 'create_bbt'
drivers/mtd/nand/onenand/onenand_bbt.c:57: warning: Function parameter or member 'chip' not described in 'create_bbt'
drivers/mtd/nand/onenand/onenand_bbt.c:132: warning: Function parameter or member 'mtd' not described in 'onenand_memory_bbt'
drivers/mtd/nand/onenand/onenand_bbt.c:132: warning: Function parameter or member 'bd' not described in 'onenand_memory_bbt'
drivers/mtd/nand/onenand/onenand_bbt.c:145: warning: Function parameter or member 'mtd' not described in 'onenand_isbad_bbt'
drivers/mtd/nand/onenand/onenand_bbt.c:145: warning: Function parameter or member 'offs' not described in 'onenand_isbad_bbt'
drivers/mtd/nand/onenand/onenand_bbt.c:145: warning: Function parameter or member 'allowbbt' not described in 'onenand_isbad_bbt'
drivers/mtd/nand/onenand/onenand_bbt.c:182: warning: Function parameter or member 'mtd' not described in 'onenand_scan_bbt'
drivers/mtd/nand/onenand/onenand_bbt.c:182: warning: Function parameter or member 'bd' not described in 'onenand_scan_bbt'
drivers/mtd/nand/onenand/onenand_bbt.c:230: warning: Function parameter or member 'mtd' not described in 'onenand_default_bbt'
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201109182206.3037326-7-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/mtd/mtdcore.c:1592: warning: Function parameter or member 'section' not described in 'mtd_ooblayout_find_eccregion'
drivers/mtd/mtdcore.c:1592: warning: Excess function parameter 'sectionp' description in 'mtd_ooblayout_find_eccregion'
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Alexander Dahl <ada@thorsis.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201109182206.3037326-6-lee.jones@linaro.org
This patch also places the descriptions in the correct order.
Fixes the following W=1 kernel build warning(s):
drivers/mtd/devices/docg3.c:819: warning: bad line:
drivers/mtd/devices/docg3.c:1799: warning: Excess function parameter 'base' description in 'doc_probe_device'
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201109182206.3037326-5-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/mtd/nand/onenand/onenand_base.c:140: warning: Function parameter or member 'mtd' not described in 'onenand_ooblayout_32_64_ecc'
drivers/mtd/nand/onenand/onenand_base.c:140: warning: Function parameter or member 'section' not described in 'onenand_ooblayout_32_64_ecc'
drivers/mtd/nand/onenand/onenand_base.c:140: warning: Function parameter or member 'oobregion' not described in 'onenand_ooblayout_32_64_ecc'
drivers/mtd/nand/onenand/onenand_base.c:200: warning: Function parameter or member 'addr' not described in 'onenand_readw'
drivers/mtd/nand/onenand/onenand_base.c:212: warning: Function parameter or member 'value' not described in 'onenand_writew'
drivers/mtd/nand/onenand/onenand_base.c:212: warning: Function parameter or member 'addr' not described in 'onenand_writew'
drivers/mtd/nand/onenand/onenand_base.c:225: warning: Function parameter or member 'this' not described in 'onenand_block_address'
drivers/mtd/nand/onenand/onenand_base.c:225: warning: Function parameter or member 'block' not described in 'onenand_block_address'
drivers/mtd/nand/onenand/onenand_base.c:242: warning: Function parameter or member 'this' not described in 'onenand_bufferram_address'
drivers/mtd/nand/onenand/onenand_base.c:242: warning: Function parameter or member 'block' not described in 'onenand_bufferram_address'
NB: Snipped 200 lines for brevity.
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Adrian Hunter <ext-adrian.hunter@nokia.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201109182206.3037326-4-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/mtd/devices/phram.c:19: warning: Function parameter or member 'fmt' not described in 'pr_fmt'
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: "Jochen Schäuble" <psionic@psionic.de>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201109182206.3037326-3-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/mtd/mtdpart.c:300: warning: Function parameter or member 'mtd' not described in '__mtd_del_partition'
drivers/mtd/mtdpart.c:300: warning: Excess function parameter 'priv' description in '__mtd_del_partition'
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Thomas Gleixner <gleixner@linutronix.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201109182206.3037326-2-lee.jones@linaro.org
The probe function is only supposed to initialize the controller
hardware but not the ECC engine. Indeed, we don't know anything about
the NAND chip(s) at this stage. Let's move the logic initializing the
ECC engine, even pretty simple, to the ->attach_chip() hook which gets
called during nand_scan() routine, after the NAND chip discovery. As
the previously mentioned logic is supposed to parse the DT for us, it
is likely that the chip->ecc.* entries be overwritten. So let's avoid
this by moving these lines to ->attach_chip().
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201113123424.32233-20-miquel.raynal@bootlin.com
The probe function is only supposed to initialize the controller
hardware but not the ECC engine. Indeed, we don't know anything about
the NAND chip(s) at this stage. Let's move the logic initializing the
ECC engine, even pretty simple, to the ->attach_chip() hook which gets
called during nand_scan() routine, after the NAND chip discovery. As
the previously mentioned logic is supposed to parse the DT for us, it
is likely that the chip->ecc.* entries be overwritten. So let's avoid
this by moving these lines to ->attach_chip().
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The probe function is only supposed to initialize the controller
hardware but not the ECC engine. Indeed, we don't know anything about
the NAND chip(s) at this stage. Let's move the logic initializing the
ECC engine, even pretty simple, to the ->attach_chip() hook which gets
called during nand_scan() routine, after the NAND chip discovery. As
the previously mentioned logic is supposed to parse the DT for us, it
is likely that the chip->ecc.* entries be overwritten. So let's avoid
this by moving these lines to ->attach_chip().
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Link: https://lore.kernel.org/linux-mtd/20201113123424.32233-18-miquel.raynal@bootlin.com
The probe function is only supposed to initialize the controller
hardware but not the ECC engine. Indeed, we don't know anything about
the NAND chip(s) at this stage. Let's move the logic initializing the
ECC engine, even pretty simple, to the ->attach_chip() hook which gets
called during nand_scan() routine, after the NAND chip discovery. As
the previously mentioned logic is supposed to parse the DT for us, it
is likely that the chip->ecc.* entries be overwritten. So let's avoid
this by moving these lines to ->attach_chip().
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201113123424.32233-17-miquel.raynal@bootlin.com
The probe function is only supposed to initialize the controller
hardware but not the ECC engine. Indeed, we don't know anything about
the NAND chip(s) at this stage. Let's move the logic initializing the
ECC engine, even pretty simple, to the ->attach_chip() hook which gets
called during nand_scan() routine, after the NAND chip discovery. As
the previously mentioned logic is supposed to parse the DT for us, it
is likely that the chip->ecc.* entries be overwritten. So let's avoid
this by moving these lines to ->attach_chip().
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201113123424.32233-16-miquel.raynal@bootlin.com
The probe function is only supposed to initialize the controller
hardware but not the ECC engine. Indeed, we don't know anything about
the NAND chip(s) at this stage. Let's move the logic initializing the
ECC engine, even pretty simple, to the ->attach_chip() hook which gets
called during nand_scan() routine, after the NAND chip discovery. As
the previously mentioned logic is supposed to parse the DT for us, it
is likely that the chip->ecc.* entries be overwritten. So let's avoid
this by moving these lines to ->attach_chip().
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201113123424.32233-15-miquel.raynal@bootlin.com
The probe function is only supposed to initialize the controller
hardware but not the ECC engine. Indeed, we don't know anything about
the NAND chip(s) at this stage. Let's move the logic initializing the
ECC engine, even pretty simple, to the ->attach_chip() hook which gets
called during nand_scan() routine, after the NAND chip discovery. As
the previously mentioned logic is supposed to parse the DT for us, it
is likely that the chip->ecc.* entries be overwritten. So let's avoid
this by moving these lines to ->attach_chip().
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201113123424.32233-14-miquel.raynal@bootlin.com
The probe function is only supposed to initialize the controller
hardware but not the ECC engine. Indeed, we don't know anything about
the NAND chip(s) at this stage. Let's move the logic initializing the
ECC engine, even pretty simple, to the ->attach_chip() hook which gets
called during nand_scan() routine, after the NAND chip discovery. As
the previously mentioned logic is supposed to parse the DT for us, it
is likely that the chip->ecc.* entries be overwritten. So let's avoid
this by moving these lines to ->attach_chip().
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201113123424.32233-13-miquel.raynal@bootlin.com
The probe function is only supposed to initialize the controller
hardware but not the ECC engine. Indeed, we don't know anything about
the NAND chip(s) at this stage. Let's move the logic initializing the
ECC engine, even pretty simple, to the ->attach_chip() hook which gets
called during nand_scan() routine, after the NAND chip discovery. As
the previously mentioned logic is supposed to parse the DT for us, it
is likely that the chip->ecc.* entries be overwritten. So let's avoid
this by moving these lines to ->attach_chip().
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201113123424.32233-12-miquel.raynal@bootlin.com
The probe function is only supposed to initialize the controller
hardware but not the ECC engine. Indeed, we don't know anything about
the NAND chip(s) at this stage. Let's move the logic initializing the
ECC engine, even pretty simple, to the ->attach_chip() hook which gets
called during nand_scan() routine, after the NAND chip discovery. As
the previously mentioned logic is supposed to parse the DT for us, it
is likely that the chip->ecc.* entries be overwritten. So let's avoid
this by moving these lines to ->attach_chip().
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Sylvain Lemieux <slemieux.tyco@gmail.com>
The probe function is only supposed to initialize the controller
hardware but not the ECC engine. Indeed, we don't know anything about
the NAND chip(s) at this stage. Let's move the logic initializing the
ECC engine, even pretty simple, to the ->attach_chip() hook which gets
called during nand_scan() routine, after the NAND chip discovery. As
the previously mentioned logic is supposed to parse the DT for us, it
is likely that the chip->ecc.* entries be overwritten. So let's avoid
this by moving these lines to ->attach_chip().
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Sylvain Lemieux <slemieux.tyco@gmail.com>
Link: https://lore.kernel.org/linux-mtd/20201113123424.32233-10-miquel.raynal@bootlin.com
The probe function is only supposed to initialize the controller
hardware but not the ECC engine. Indeed, we don't know anything about
the NAND chip(s) at this stage. Let's move the logic initializing the
ECC engine, even pretty simple, to the ->attach_chip() hook which gets
called during nand_scan() routine, after the NAND chip discovery. As
the previously mentioned logic is supposed to parse the DT for us, it
is likely that the chip->ecc.* entries be overwritten. So let's avoid
this by moving these lines to ->attach_chip().
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The probe function is only supposed to initialize the controller
hardware but not the ECC engine. Indeed, we don't know anything about
the NAND chip(s) at this stage. Let's move the logic initializing the
ECC engine, even pretty simple, to the ->attach_chip() hook which gets
called during nand_scan() routine, after the NAND chip discovery. As
the previously mentioned logic is supposed to parse the DT for us, it
is likely that the chip->ecc.* entries be overwritten. So let's avoid
this by moving these lines to ->attach_chip().
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201113123424.32233-8-miquel.raynal@bootlin.com
The probe function is only supposed to initialize the controller
hardware but not the ECC engine. Indeed, we don't know anything about
the NAND chip(s) at this stage. Let's move the logic initializing the
ECC engine, even pretty simple, to the ->attach_chip() hook which gets
called during nand_scan() routine, after the NAND chip discovery. As
the previously mentioned logic is supposed to parse the DT for us, it
is likely that the chip->ecc.* entries be overwritten. So let's avoid
this by moving these lines to ->attach_chip().
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/linux-mtd/20201113123424.32233-7-miquel.raynal@bootlin.com
The probe function is only supposed to initialize the controller
hardware but not the ECC engine. Indeed, we don't know anything about
the NAND chip(s) at this stage. Let's move the logic initializing the
ECC engine, even pretty simple, to the ->attach_chip() hook which gets
called during nand_scan() routine, after the NAND chip discovery. As
the previously mentioned logic is supposed to parse the DT for us, it
is likely that the chip->ecc.* entries be overwritten. So let's avoid
this by moving these lines to ->attach_chip().
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The probe function is only supposed to initialize the controller
hardware but not the ECC engine. Indeed, we don't know anything about
the NAND chip(s) at this stage. Let's move the logic initializing the
ECC engine, even pretty simple, to the ->attach_chip() hook which gets
called during nand_scan() routine, after the NAND chip discovery. As
the previously mentioned logic is supposed to parse the DT for us, it
is likely that the chip->ecc.* entries be overwritten. So let's avoid
this by moving these lines to ->attach_chip().
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201113123424.32233-5-miquel.raynal@bootlin.com
The probe function is only supposed to initialize the controller
hardware but not the ECC engine. Indeed, we don't know anything about
the NAND chip(s) at this stage. Let's move the logic initializing the
ECC engine, even pretty simple, to the ->attach_chip() hook which gets
called during nand_scan() routine, after the NAND chip discovery. As
the previously mentioned logic is supposed to parse the DT for us, it
is likely that the chip->ecc.* entries be overwritten. So let's avoid
this by moving these lines to ->attach_chip().
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201113123424.32233-4-miquel.raynal@bootlin.com
The probe function is only supposed to initialize the controller
hardware but not the ECC engine. Indeed, we don't know anything about
the NAND chip(s) at this stage. Let's move the logic initializing the
ECC engine, even pretty simple, to the ->attach_chip() hook which gets
called during nand_scan() routine, after the NAND chip discovery. As
the previously mentioned logic is supposed to parse the DT for us, it
is likely that the chip->ecc.* entries be overwritten. So let's avoid
this by moving these lines to ->attach_chip(), a NAND controller
hook.
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201113123424.32233-3-miquel.raynal@bootlin.com
The probe function is only supposed to initialize the controller
hardware but not the ECC engine. Indeed, we don't know anything about
the NAND chip(s) at this stage. Let's move the logic initializing the
ECC engine, even pretty simple, to the ->attach_chip() hook which gets
called during nand_scan() routine, after the NAND chip discovery. As
the previously mentioned logic is supposed to parse the DT for us, it
is likely that the chip->ecc.* entries be overwritten. So let's avoid
this by moving these lines to ->attach_chip(), a NAND controller
hook.
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Reported-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/linux-mtd/20201113123424.32233-2-miquel.raynal@bootlin.com
BLKFLSBUF is not supposed to actually send a flush command to the device,
but to tear down buffer cache structures. Remove the mtd_blkdevs
implementation and just use the default semantics instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Since this flash doesn't have a Profile 1.0 table, the Octal DTR
capabilities are enabled in the post SFDP fixup, along with the 8D-8D-8D
fast read settings.
Enable Octal DTR mode with 20 dummy cycles to allow running at the
maximum supported frequency of 200Mhz.
The flash supports the soft reset sequence. So, add the flag in the
flash's info.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201005153138.6437-16-p.yadav@ti.com
The Cypress Semper flash is an xSPI compliant octal DTR flash. Add
support for using it in octal DTR mode.
The flash by default boots in a hybrid sector mode. But the sector map
table on the part I had was programmed incorrectly and the SMPT values
on the flash don't match the public datasheet. Specifically, in some
places erase type 3 was used instead of 4. In addition, the region sizes
were incorrect in some places. So, for testing I set CFR3N[3] to enable
uniform sector sizes. Since the uniform sector mode bit is a
non-volatile bit, this series does not change it to avoid making any
permanent changes to the flash configuration. The correct data to
implement a fixup is not available right now and will be done in a
follow-up patch if needed.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
[vigneshr@ti.com: Drop unnecessary sleep in Octal DTR switch sequence]
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201005153138.6437-15-p.yadav@ti.com
On resume, the init procedure will be run that will re-enable it.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201005153138.6437-14-p.yadav@ti.com
Perform a Soft Reset on shutdown on flashes that support it so that the
flash can be reset to its initial state and any configurations made by
spi-nor (given that they're only done in volatile registers) will be
reset. This will hand back the flash in pristine state for any further
operations on it.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201005153138.6437-13-p.yadav@ti.com
A Soft Reset sequence will return the flash to Power-on-Reset (POR)
state. It consists of two commands: Soft Reset Enable and Soft Reset.
Find out if the sequence is supported from BFPT DWORD 16.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201005153138.6437-12-p.yadav@ti.com
Allow flashes to specify a hook to enable octal DTR mode. Use this hook
whenever possible to get optimal transfer speeds.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201005153138.6437-11-p.yadav@ti.com
Parse just the 22nd dword and look for the 'DTR Octal Mode Enable
Volatile bit'.
SPI_NOR_IO_MODE_EN_VOLATILE should be set just for the flashes
that don't define the optional SFDP SCCR Map. For the others,
let the SFDP do its job and fill the SNOR_F_IO_MODE_EN_VOLATILE
flag. We avoid this way polluting the flash flags when declaring
one.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20201005153138.6437-10-p.yadav@ti.com
We don't want to enter a stateful mode, where a X-X-X I/O mode
is entered by setting a non-volatile bit, because in case of a
reset or a crash, once in the non-volatile mode, we may not be able
to recover in bootloaders and we may break the SPI NOR boot.
Forbid by default the I/O modes that are set via a non-volatile bit.
SPI_NOR_IO_MODE_EN_VOLATILE should be set just for the flashes that
don't define the optional SFDP SCCR Map, so that we don't pollute the
flash info flags.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20201005153138.6437-9-p.yadav@ti.com
Some controllers, like the cadence qspi controller, have trouble reading
only 1 byte in DTR mode. So, do 2 byte reads for SR and FSR commands in
DTR mode, and then discard the second byte.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201005153138.6437-8-p.yadav@ti.com
The xSPI Profile 1.0 table specifies how many dummy cycles and address
bytes are needed for the Read Status Register command in octal DTR mode.
Use that information to send the correct Read SR command.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201005153138.6437-7-p.yadav@ti.com
This table is indication that the flash is xSPI compliant and hence
supports octal DTR mode. Extract information like the fast read opcode,
dummy cycles, the number of dummy cycles needed for a Read Status
Register command, and the number of address bytes needed for a Read
Status Register command.
We don't know what speed the controller is running at. Find the fast
read dummy cycles for the fastest frequency the flash can run at to be
sure we are never short of dummy cycles. If nothing is available,
default to 20. Flashes that use a different value should update it in
their fixup hooks.
Since we want to set read settings, expose spi_nor_set_read_settings()
in core.h.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201005153138.6437-6-p.yadav@ti.com
Some devices in DTR mode expect an extra command byte called the
extension. The extension can either be same as the opcode, bitwise
inverse of the opcode, or another additional byte forming a 16-byte
opcode. Get the extension type from the BFPT. For now, only flashes with
"repeat" and "inverse" extensions are supported.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201005153138.6437-5-p.yadav@ti.com
Double Transfer Rate (DTR) is SPI protocol in which data is transferred
on each clock edge as opposed to on each clock cycle. Make
framework-level changes to allow supporting flashes in DTR mode.
Right now, mixed DTR modes are not supported. So, for example a mode
like 4S-4D-4D will not work. All phases need to be either DTR or STR.
The xSPI spec says that "The program commands provide SPI backward
compatible commands for programming data...". So 8D-8D-8D page program
opcodes are populated with using 1S-1S-1S opcodes.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201005153138.6437-4-p.yadav@ti.com
They are thin wrappers around
nor->controller_ops->{read_reg,write_reg,erase}(). In a future commit
DTR support will be added. These ops can not be supported by the
controller_ops hooks and these helpers will make it easier to reject
those calls.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201005153138.6437-3-p.yadav@ti.com
ENOTSUPP is not a SUSV4 error code. Using EOPNOTSUPP is preferred
in its stead.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201005153138.6437-2-p.yadav@ti.com
Since commit d7157ff49a ("mtd: rawnand: Use the ECC framework user
input parsing bits"), ECC are broken in FMC2 driver in case of
nand-ecc-step-size and nand-ecc-strength are not set in the device tree.
To avoid this issue, the default settings are now set in
stm32_fmc2_nfc_attach_chip function.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1604064819-26861-1-git-send-email-christophe.kerello@st.com
If a flash chip has more than 16MB capacity but its BFPT reports
BFPT_DWORD1_ADDRESS_BYTES_3_OR_4, the spi-nor framework defaults to 3.
The check in spi_nor_set_addr_width() doesn't catch it because addr_width
did get set. This fixes that check.
Fixes: f9acd7fa80 ("mtd: spi-nor: sfdp: default to addr_width of 3 for configurable widths")
Signed-off-by: Bert Vermeulen <bert@biot.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Joel Stanley <joel@jms.id.au>
Tested-by: Cédric Le Goater <clg@kaod.org>
Link: https://lore.kernel.org/r/20201006132346.12652-1-bert@biot.com
No ECC initialization should happen during the host controller probe.
In fact, we need the probe function to call nand_scan() in order to:
- identify the device, its capabilities and constraints (nand_scan_ident())
- configure the ECC engine accordingly (->attach_chip())
- scan its content and prepare the core (nand_scan_tail())
Moving these lines to fsl_ifc_attach_chip() fixes a regression caused by
a previous commit supposed to clarify these steps.
Based on a fix done for the mxc_nand driver by Miquel Raynal.
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Reported-by: Han Xu <xhnjupt@gmail.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Han Xu <xhnjupt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201016132626.30112-1-festevam@gmail.com
No ECC initialization should happen during the host controller probe.
In fact, we need the probe function to call nand_scan() in order to:
- identify the device, its capabilities and constraints (nand_scan_ident())
- configure the ECC engine accordingly (->attach_chip())
- scan its content and prepare the core (nand_scan_tail())
Moving these lines to mxcnd_attach_chip() fixes a regression caused by
a previous commit supposed to clarify these steps.
When moving the ECC initialization from probe() to attach(), get rid
of the pdata usage to determine the engine type and let the core decide
instead.
Tested on a imx27-pdk board.
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Reported-by: Fabio Estevam <festevam@gmail.com>
Co-developed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201016213613.1450-1-festevam@gmail.com
UBI:
- Correctly use kthread_should_stop in ubi worker
UBIFS:
- Fixes for memory leaks while iterating directory entries
- Fix for a user triggerable error message
- Fix for a space accounting bug in authenticated mode
-----BEGIN PGP SIGNATURE-----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=RD+h
-----END PGP SIGNATURE-----
Merge tag 'for-linus-5.10-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs
Pull more ubi and ubifs updates from Richard Weinberger:
"UBI:
- Correctly use kthread_should_stop in ubi worker
UBIFS:
- Fixes for memory leaks while iterating directory entries
- Fix for a user triggerable error message
- Fix for a space accounting bug in authenticated mode"
* tag 'for-linus-5.10-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs:
ubifs: journal: Make sure to not dirty twice for auth nodes
ubifs: setflags: Don't show error message when vfs_ioc_setflags_prepare() fails
ubifs: ubifs_jnl_change_xattr: Remove assertion 'nlink > 0' for host inode
ubi: check kthread_should_stop() after the setting of task state
ubifs: dent: Fix some potential memory leaks while iterating entries
ubifs: xattr: Fix some potential memory leaks while iterating entries
* Drop useless 'depends on' in Kconfig
* Add an extra level in the Kconfig hierarchy
* Trivial spellings
* Dynamic allocation of the interface configurations
* Dropping the default ONFI timing mode
* Various cleanup (types, structures, naming, comments)
* Hide the chip->data_interface indirection
* Add the generic rb-gpios property
* Add the ->choose_interface_config() hook
* Introduce nand_choose_best_sdr_timings()
* Use default values for tPROG_max and tBERS_max
* Avoid redefining tR_max and tCCS_min
* Add a helper to find the closest ONFI mode
* bcm63xx MTD parsers: simplify CFE detection
Raw NAND controller drivers changes:
* fsl-upm: Deprecation of specific DT properties
* fsl_upm: Driver rework and cleanup in favor of ->exec_op()
* Ingenic: Cleanup ARRAY_SIZE() vs sizeof() use
* brcmnand: ECC error handling on EDU transfers
* brcmnand: Don't default to EDU transfers
* qcom: Set BAM mode only if not set already
* qcom: Avoid write to unavailable register
* gpio: Driver rework in favor of ->exec_op()
* tango: ->exec_op() conversion
* mtk: ->exec_op() conversion
Raw NAND chip drivers changes:
* toshiba: Implement ->choose_interface_config() for TH58NVG2S3HBAI4
* toshiba: Implement ->choose_interface_config() for TC58NVG0S3E
* toshiba: Implement ->choose_interface_config() for TC58TEG5DCLTA00
* hynix: Implement ->choose_interface_config() for H27UCG8T2ATR-BC
HyperBus changes:
* DMA support for TI's AM654 HyperBus controller driver.
* HyperBus frontend driver for Renesas RPC-IF driver.
SPI NOR core changes:
* Support for Winbond w25q64jwm flash
* Enable 4K sector support for mx25l12805d
SPI NOR controller drivers changes:
* intel-spi Add Alder Lake-S PCI ID
MTD Core changes:
* mtdoops: Don't run panic write twice
* mtdconcat: Correctly handle panic write
* Use DEFINE_SHOW_ATTRIBUTE
-----BEGIN PGP SIGNATURE-----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=X56H
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Richard Weinberger:
"NAND core changes:
- Drop useless 'depends on' in Kconfig
- Add an extra level in the Kconfig hierarchy
- Trivial spellings
- Dynamic allocation of the interface configurations
- Dropping the default ONFI timing mode
- Various cleanup (types, structures, naming, comments)
- Hide the chip->data_interface indirection
- Add the generic rb-gpios property
- Add the ->choose_interface_config() hook
- Introduce nand_choose_best_sdr_timings()
- Use default values for tPROG_max and tBERS_max
- Avoid redefining tR_max and tCCS_min
- Add a helper to find the closest ONFI mode
- bcm63xx MTD parsers: simplify CFE detection
Raw NAND controller drivers changes:
- fsl-upm: Deprecation of specific DT properties
- fsl_upm: Driver rework and cleanup in favor of ->exec_op()
- Ingenic: Cleanup ARRAY_SIZE() vs sizeof() use
- brcmnand: ECC error handling on EDU transfers
- brcmnand: Don't default to EDU transfers
- qcom: Set BAM mode only if not set already
- qcom: Avoid write to unavailable register
- gpio: Driver rework in favor of ->exec_op()
- tango: ->exec_op() conversion
- mtk: ->exec_op() conversion
Raw NAND chip drivers changes:
- toshiba: Implement ->choose_interface_config() for TH58NVG2S3HBAI4
- toshiba: Implement ->choose_interface_config() for TC58NVG0S3E
- toshiba: Implement ->choose_interface_config() for TC58TEG5DCLTA00
- hynix: Implement ->choose_interface_config() for H27UCG8T2ATR-BC
HyperBus changes:
- DMA support for TI's AM654 HyperBus controller driver.
- HyperBus frontend driver for Renesas RPC-IF driver.
SPI NOR core changes:
- Support for Winbond w25q64jwm flash
- Enable 4K sector support for mx25l12805d
SPI NOR controller drivers changes:
- intel-spi Add Alder Lake-S PCI ID
MTD Core changes:
- mtdoops: Don't run panic write twice
- mtdconcat: Correctly handle panic write
- Use DEFINE_SHOW_ATTRIBUTE"
* tag 'mtd/for-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (76 commits)
mtd: hyperbus: Fix build failure when only RPCIF_HYPERBUS is enabled
mtd: hyperbus: add Renesas RPC-IF driver
Revert "mtd: spi-nor: Prefer asynchronous probe"
mtd: parsers: bcm63xx: Do not make it modular
mtd: spear_smi: Enable compile testing
mtd: maps: vmu-flash: fix typos for struct memcard
mtd: physmap: Add Baikal-T1 physically mapped ROM support
mtd: maps: vmu-flash: simplify the return expression of probe_maple_vmu
mtd: onenand: simplify the return expression of onenand_transfer_auto_oob
mtd: rawnand: cadence: remove a redundant dev_err call
mtd: rawnand: ams-delta: Fix non-OF build warning
mtd: rawnand: Don't overwrite the error code from nand_set_ecc_soft_ops()
mtd: rawnand: Introduce nand_set_ecc_on_host_ops()
mtd: rawnand: atmel: Check return values for nand_read_data_op
mtd: rawnand: vf610: Remove unused function vf610_nfc_transfer_size()
mtd: rawnand: qcom: Simplify with dev_err_probe()
mtd: rawnand: marvell: Fix and update kerneldoc
mtd: rawnand: marvell: Simplify with dev_err_probe()
mtd: rawnand: gpmi: Simplify with dev_err_probe()
mtd: rawnand: atmel: Simplify with dev_err_probe()
...
Pull trivial updates from Jiri Kosina:
"The latest advances in computer science from the trivial queue"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
xtensa: fix Kconfig typo
spelling.txt: Remove some duplicate entries
mtd: rawnand: oxnas: cleanup/simplify code
selftests: vm: add fragment CONFIG_GUP_BENCHMARK
perf: Fix opt help text for --no-bpf-event
HID: logitech-dj: Fix spelling in comment
bootconfig: Fix kernel message mentioning CONFIG_BOOT_CONFIG
MAINTAINERS: rectify MMP SUPPORT after moving cputype.h
scif: Fix spelling of EACCES
printk: fix global comment
lib/bitmap.c: fix spello
fs: Fix missing 'bit' in comment
-----BEGIN PGP SIGNATURE-----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=LzyE
-----END PGP SIGNATURE-----
Merge tag 'block-5.10-2020-10-12' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
- Series of merge handling cleanups (Baolin, Christoph)
- Series of blk-throttle fixes and cleanups (Baolin)
- Series cleaning up BDI, seperating the block device from the
backing_dev_info (Christoph)
- Removal of bdget() as a generic API (Christoph)
- Removal of blkdev_get() as a generic API (Christoph)
- Cleanup of is-partition checks (Christoph)
- Series reworking disk revalidation (Christoph)
- Series cleaning up bio flags (Christoph)
- bio crypt fixes (Eric)
- IO stats inflight tweak (Gabriel)
- blk-mq tags fixes (Hannes)
- Buffer invalidation fixes (Jan)
- Allow soft limits for zone append (Johannes)
- Shared tag set improvements (John, Kashyap)
- Allow IOPRIO_CLASS_RT for CAP_SYS_NICE (Khazhismel)
- DM no-wait support (Mike, Konstantin)
- Request allocation improvements (Ming)
- Allow md/dm/bcache to use IO stat helpers (Song)
- Series improving blk-iocost (Tejun)
- Various cleanups (Geert, Damien, Danny, Julia, Tetsuo, Tian, Wang,
Xianting, Yang, Yufen, yangerkun)
* tag 'block-5.10-2020-10-12' of git://git.kernel.dk/linux-block: (191 commits)
block: fix uapi blkzoned.h comments
blk-mq: move cancel of hctx->run_work to the front of blk_exit_queue
blk-mq: get rid of the dead flush handle code path
block: get rid of unnecessary local variable
block: fix comment and add lockdep assert
blk-mq: use helper function to test hw stopped
block: use helper function to test queue register
block: remove redundant mq check
block: invoke blk_mq_exit_sched no matter whether have .exit_sched
percpu_ref: don't refer to ref->data if it isn't allocated
block: ratelimit handle_bad_sector() message
blk-throttle: Re-use the throtl_set_slice_end()
blk-throttle: Open code __throtl_de/enqueue_tg()
blk-throttle: Move service tree validation out of the throtl_rb_first()
blk-throttle: Move the list operation after list validation
blk-throttle: Fix IO hang for a corner case
blk-throttle: Avoid tracking latency if low limit is invalid
blk-throttle: Avoid getting the current time if tg->last_finish_time is 0
blk-throttle: Remove a meaningless parameter for throtl_downgrade_state()
block: Remove redundant 'return' statement
...
commit 5de15b610f ("mtd: hyperbus: add Renesas RPC-IF driver") leads
to build failure[1] with COMPILE_TEST and RPCIF_HYPERBUS enabled. This
is because driver needs functions RENESAS_RPCIF which is only buildable
for CONFIG_ARCH_RENESAS.
Fix this by dropping COMPILE_TEST from RPCIF_HYPERBUS Kconfig entry.
This ensures driver can be built only when RENESAS_RPCIF is also
selected.
[1]:
rpc-if.c:(.text+0x20): undefined reference to `rpcif_disable_rpm' ld:
drivers/mtd/hyperbus/rpc-if.o: in function `rpcif_hb_prepare_read':
rpc-if.c:(.text+0xd6): undefined reference to `rpcif_prepare' ld:
drivers/mtd/hyperbus/rpc-if.o: in function `rpcif_hb_read16':
[...]
Fixes: 5de15b610f ("mtd: hyperbus: add Renesas RPC-IF driver") leads
Reported-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
- Support for Winbond w25q64jwm flash
- Enable 4K sector support for mx25l12805d
SPI NOR controller drivers changes:
- intel-spi:
- Add Alder Lake-S PCI ID
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEEyRC2zAhGcGjrhiNExEYeRXyRFuMFAl+AUmoQHHZpZ25lc2hy
QHRpLmNvbQAKCRDERh5FfJEW4y/WB/sH/LcaUciOptcqKQVQcQ5QVV3oj208Oj0F
f+BOk4bt0UJlKEz4szWThOL7UrNd/1jkvxn5wdz9R1pPYdvqor66wXH1fCHSJWIG
EQDIEjcNy2O7MO6oTNNXEoqPc829yUYGsxbcqz54wRHIAkJxiXJCyx3iRt+ymzIR
+NFrcsGjy4ftRo47tn/SGnDHSYtkaPiGiXWqIS114daRtMcQuJMIshalzZ5woKSp
Eyj2+fpcusM72aLtk9DEjBuQBBb7w6fL3wZuAYTFIU7utS3ruqfbTFwS9uvgiH6g
/cuddR2Ku2tBIOllmiwOEsFq/aDmxn6zWp0nW3JNq5nNRarOCfQS
=lh89
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux into mtd/next
SPI NOR core changes:
- Support for Winbond w25q64jwm flash
- Enable 4K sector support for mx25l12805d
SPI NOR controller drivers changes:
- intel-spi:
- Add Alder Lake-S PCI ID
* Use the new generic ECC object
* Create helpers to set/extract the ECC requirements
* Create a helper to extract the ECC configuration
* Add a NAND page I/O request type
* Introduce the ECC engine framework
Raw NAND core changes:
* Don't overwrite the error code from nand_set_ecc_soft_ops()
* Introduce nand_set_ecc_on_host_ops()
* Use the NAND framework user_conf object for ECC flags
* Use the ECC framework user input parsing bits
* Use the ECC framework nand_ecc_is_strong_enough() helper
* Use the ECC framework OOB layouts
* Make use of the ECC framework
* Use nanddev_get/set_ecc_requirements() when relevant
* Use the new ECC engine type enumeration
* Separate the ECC engine type and the ECC byte placement
* Move the nand_ecc_algo enum to the generic NAND layer
* Rename the ECC algorithm enumeration items
* Add a kernel doc to the ECC algorithm enumeration
* DT bindings:
- Document boolean NAND ECC properties
- Document nand-ecc-engine
- Document nand-ecc-placement
Raw NAND drivers changes:
* Ams-Delta: Fix non-OF build warning
* Atmel:
- Check return values for nand_read_data_op
- Simplify with dev_err_probe()
- Get rid of the legacy interface implementation
- Convert the driver to exec_op()
- Use nand_prog_page_end_op()
- Use nand_{write,read}_data_op()
- Drop redundant nand_read_page_op()
- Enable the NFC controller at probe time
- Disable clk on error handling path in probe
* Cadence: remove a redundant dev_err call
* Gpmi:
- Simplify with dev_err_probe()
* Marvell:
- Fix and update kerneldoc
- Simplify with dev_err_probe()
- Fix and update kerneldoc
- Simplify with dev_err_probe()
- Support panic_write for mtdoops
* Onenand:
- Simplify the return expression of onenand_transfer_auto_oob
- Simplify with dev_err_probe()
* Oxnas: cleanup/simplify code
* Pasemi: Make pasemi_device_ready() static
* Qcom: Simplify with dev_err_probe()
* Stm32_fmc2: fix a buffer overflow
* Vf610: Remove unused function vf610_nfc_transfer_size()
SPI-NAND changes:
* Use nanddev_get_ecc_conf() when relevant
* Gigadevice:
- Add support for GD5F4GQ4xC
- Add QE Bit
- Use only one dummy byte in QUADIO
* Macronix:
- Add support for MX31UF1GE4BC
- Add support for MX31LF1GE4BC
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl+DYmkACgkQJWrqGEe9
VoQ3hQgAuKfV+RcsLq2S7jRjX3ET2U86NyqMIdTMhyu1n3EsW/Ipvu3FESMWnSQV
QO6oWogK/YstDO9huhC4dmJq9YYt3ia2e/4V3BMKpF4evCM4H16AtjKj1hl87r/L
3NDj3pvVaXxgIu7Rorr9Wk1+Fd/HSdgFXp/dqr+5EtltoKEB1/a+z5wLaCuDHjOm
btS42ihODYpefNDoakKSzYsdU1h4PyIWfqpEfWtQD1AAuaqIotfbjUO1oOjjdx+7
Lxy055VhwWpjUlU7bJhIM6qMj7JvB+ApFudB9ddg7VQITv+gb5ectsTZOfrGd27r
YX1/b8i1kAEZJ0uI/cz1MY1lYa8/xA==
=GSLS
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux into mtd/next
NAND core changes:
* Use the new generic ECC object
* Create helpers to set/extract the ECC requirements
* Create a helper to extract the ECC configuration
* Add a NAND page I/O request type
* Introduce the ECC engine framework
Raw NAND core changes:
* Don't overwrite the error code from nand_set_ecc_soft_ops()
* Introduce nand_set_ecc_on_host_ops()
* Use the NAND framework user_conf object for ECC flags
* Use the ECC framework user input parsing bits
* Use the ECC framework nand_ecc_is_strong_enough() helper
* Use the ECC framework OOB layouts
* Make use of the ECC framework
* Use nanddev_get/set_ecc_requirements() when relevant
* Use the new ECC engine type enumeration
* Separate the ECC engine type and the ECC byte placement
* Move the nand_ecc_algo enum to the generic NAND layer
* Rename the ECC algorithm enumeration items
* Add a kernel doc to the ECC algorithm enumeration
* DT bindings:
- Document boolean NAND ECC properties
- Document nand-ecc-engine
- Document nand-ecc-placement
Raw NAND drivers changes:
* Ams-Delta: Fix non-OF build warning
* Atmel:
- Check return values for nand_read_data_op
- Simplify with dev_err_probe()
- Get rid of the legacy interface implementation
- Convert the driver to exec_op()
- Use nand_prog_page_end_op()
- Use nand_{write,read}_data_op()
- Drop redundant nand_read_page_op()
- Enable the NFC controller at probe time
- Disable clk on error handling path in probe
* Cadence: remove a redundant dev_err call
* Gpmi:
- Simplify with dev_err_probe()
* Marvell:
- Fix and update kerneldoc
- Simplify with dev_err_probe()
- Fix and update kerneldoc
- Simplify with dev_err_probe()
- Support panic_write for mtdoops
* Onenand:
- Simplify the return expression of onenand_transfer_auto_oob
- Simplify with dev_err_probe()
* Oxnas: cleanup/simplify code
* Pasemi: Make pasemi_device_ready() static
* Qcom: Simplify with dev_err_probe()
* Stm32_fmc2: fix a buffer overflow
* Vf610: Remove unused function vf610_nfc_transfer_size()
SPI-NAND changes:
* Use nanddev_get_ecc_conf() when relevant
* Gigadevice:
- Add support for GD5F4GQ4xC
- Add QE Bit
- Use only one dummy byte in QUADIO
* Macronix:
- Add support for MX31UF1GE4BC
- Add support for MX31LF1GE4BC
Add the HyperFLash driver for the Renesas RPC-IF. It's the "front end"
driver using the "back end" APIs in the main driver to talk to the real
hardware.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/78abb851-2beb-fe7d-87e5-ce58ee877d35@gmail.com
This reverts commit 03edda0e1e.
This leads to warn dump like [1] on some platforms and reorders MTD
devices which may break user space expectations [2]. So revert the change.
[1]:
[ 1.849801] ------------[ cut here ]------------
[ 1.854271] mscc_felix 0000:00:00.5: device is disabled, skipping
[ 1.858753] WARNING: CPU: 1 PID: 7 at kernel/kmod.c:136 __request_module+0x3a4/0x568
[...]
[2] Bug report: https://lore.kernel.org/linux-mtd/20201003150633.23416-1-michael@walle.cc/
Reported-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20201005090321.8724-1-vigneshr@ti.com
With commit 91e81150d3 ("mtd: parsers: bcm63xx: simplify CFE
detection"), we generate a reference to fw_arg3 which is the fourth
firmware/command line argument on MIPS platforms. That symbol is not
exported and would cause a linking failure.
The parser is typically necessary to boot a BCM63xx-based system anyway
so having it be part of the kernel image makes sense, therefore make it
'bool' instead of 'tristate'.
Fixes: 91e81150d3 ("mtd: parsers: bcm63xx: simplify CFE detection")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200929172726.30469-1-f.fainelli@gmail.com
Baikal-T1 Boot Controller provides an access to a RO storages, which are
physically mapped into the SoC MMIO space. In particularly there are
Internal ROM embedded into the SoC with a pre-installed firmware,
externally attached SPI flash (also accessed in the read-only mode) and a
memory region, which mirrors one of them in accordance with the currently
enabled system boot mode (also called Boot ROM).
This commit adds the Internal ROM support to the physmap driver of the MTD
kernel subsystem. The driver will create the Internal ROM MTD as long as
it is defined in the system dts file. The physically mapped SPI flash
region will be used to implement the SPI-mem interface. The mirroring
memory region won't be accessible directly since it's redundant due to
both bootable regions being exposed anyway.
Note we had to create a dedicated code for the ROMs since read from the
corresponding memory regions must be done via the dword-aligned addresses.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Pavel Parkhomenko <Pavel.Parkhomenko@baikalelectronics.ru>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: linux-mips@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200920111445.21816-1-Sergey.Semin@baikalelectronics.ru
There is an error message within devm_ioremap_resource already, so
remove the dev_err call to avoid a redundant error message.
Signed-off-by: Liu Shixin <liushixin2@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200921013805.1724606-1-liushixin2@huawei.com
Commit 7c2f66a960 ("mtd: rawnand: ams-delta: Add module device
tables") introduced an OF module device table but wrapped a reference
to it with of_match_ptr() which resolves to NULL in non-OF configs.
That resulted in a clang compiler warning on unused variable in non-OF
builds. Fix it.
drivers/mtd/nand/raw/ams-delta.c:373:34: warning: unused variable 'gpio_nand_of_id_table' [-Wunused-const-variable]
static const struct of_device_id gpio_nand_of_id_table[] = {
^
1 warning generated.
Fixes: 7c2f66a960 ("mtd: rawnand: ams-delta: Add module device tables")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200919080403.17520-1-jmkrzyszt@gmail.com
The error code received from nand_set_ecc_soft_ops() was overwritten,
drop this redundant assignment and use the error code received from
the callee.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200917075213.532161-4-tudor.ambarus@microchip.com
There were too many levels of indentation and the code was
hard to read. Introduce a new function, similar to
nand_set_ecc_soft_ops().
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200917075213.532161-3-tudor.ambarus@microchip.com
In atmel_nand_pmecc_read_pg(), nand_read_data_op() is called twice
without the return values being checked for errors. Add these checks.
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200914214245.14626-1-alex.dewar90@gmail.com
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200901142535.12819-6-krzk@kernel.org
Fix kerneldoc comments and add missing documentation for members to fix
W=1 compile warnings like:
drivers/mtd/nand/raw/marvell_nand.c:251: warning:
cannot understand function prototype: 'struct marvell_hw_ecc_layout '
drivers/mtd/nand/raw/marvell_nand.c:342: warning:
Function parameter or member 'layout' not described in 'marvell_nand_chip'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200901142535.12819-5-krzk@kernel.org
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200901142535.12819-4-krzk@kernel.org
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200901142535.12819-3-krzk@kernel.org
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200901142535.12819-2-krzk@kernel.org
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200901142535.12819-1-krzk@kernel.org
The following GigaDevice chips have the QE BIT in the feature flags, I
checked the datasheets, but did not try this.
* GD5F1GQ4xExxG
* GD5F1GQ4xFxxG
* GD5F1GQ4UAYIG
* GD5F4GQ4UAYIG
The Quad operations like 0xEB mention that the QE bit has to be set.
Fixes: c93c613214 ("mtd: spinand: add support for GigaDevice GD5FxGQ4xA")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200820165121.3192-3-hauke@hauke-m.de
The datasheet only lists one dummy byte in the 0xEH operation for the
following chips:
* GD5F1GQ4xExxG
* GD5F1GQ4xFxxG
* GD5F1GQ4UAYIG
* GD5F4GQ4UAYIG
Fixes: c93c613214 ("mtd: spinand: add support for GigaDevice GD5FxGQ4xA")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200820165121.3192-2-hauke@hauke-m.de
vf610_nfc_probe() does not invoke clk_disable_unprepare() on one error
handling path. The patch fixes that.
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 6f0ce4dfc5 ("mtd: rawnand: vf610: Avoid a potential NULL pointer dereference")
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200806072634.23528-1-novikov@ispras.ru
The Macronix MX31UF1GE4BC is a 1.8V, 1Gbit (128MB) serial
NAND flash device.
Validated by read, erase, read back, write and read back
on Xilinx Zynq PicoZed FPGA board which included
Macronix SPI Host (driver/spi/spi-mxic.c).
Signed-off-by: YouChing Lin <ycllin@mxic.com.tw>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1595404978-31079-3-git-send-email-ycllin@mxic.com.tw
The Macronix MX31LF1GE4BC is a 3V, 1Gbit (128MB) serial
NAND flash device.
Validated by read, erase, read back, write and read back
on Xilinx Zynq PicoZed FPGA board which included
Macronix SPI Host (driver/spi/spi-mxic.c).
Signed-off-by: YouChing Lin <ycllin@mxic.com.tw>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1595404978-31079-2-git-send-email-ycllin@mxic.com.tw
The sparse tool complains as follows:
drivers/mtd/nand/raw/pasemi_nand.c:71:5: warning:
symbol 'pasemi_device_ready' was not declared. Should it be static?
This function is not used outside of pasemi_nand.c, so this commit
marks it static.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200721151657.41027-1-weiyongjun1@huawei.com
Now that exec_op() is implemented, we can get rid of all the legacy
hooks.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200720131356.1579073-7-tudor.ambarus@microchip.com
Use the nand_{write,read}_data_op() helpers instead of calling the
atmel_nand_{read,write}_buf() functions directly. This will ease the
transition to exec_op().
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200720131356.1579073-4-tudor.ambarus@microchip.com
No need to enable it everytime select_chip() is called. If we really
care about PM, we should implement runtime PM hooks and disable the
controller and all its clocks when the controller has been unused for
some time.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200720131356.1579073-2-tudor.ambarus@microchip.com
Many helpers are generic to all NAND chips, they should not be
raw-NAND specific, so use the generic ones.
To avoid moving all the raw NAND core "history" into the generic NAND
layer, we keep a part of this parsing in the raw NAND core to ensure
backward compatibility.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200827085208.16276-20-miquel.raynal@bootlin.com
AM654 HyperBus controller provides MMIO interface to read data from
flash. So add DMA memcpy support for reading data over MMIO interface.
This provides 5x improvement in throughput and reduces CPU usage as
well.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20200924081214.16934-5-vigneshr@ti.com
Recent genpd changes for K3 platform ensure device is ON before driver
probe is called. Therefore, drop redundant pm_runtime_* calls from
driver to simplify the code.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200924081214.16934-4-vigneshr@ti.com
Setting up of direct mapping should be done with flash node's IO
address space and not with controller's IO region.
Fixes: b6fe8bc67d ("mtd: hyperbus: move direct mapping setup to AM654 HBMC driver")
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200924081214.16934-3-vigneshr@ti.com
Add support Winbond w25q{64,128,256}jwm which are identical to existing
w25q32jwm except for their sizes.
This was tested with w25q64jwm, basic erase/write/readback and
lock/unlock both lower/upper blocks were okay.
Signed-off-by: ikjn@chromium.org <ikjn@chromium.org>
Signed-off-by: Xingyu Wu <wuxy@bitland.corp-partner.google.com>
Signed-off-by: ST Lin <stlin2@winbond.com>
Tested-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200928060631.2090541-1-ikjn@chromium.org
Intel Alder Lake-S has the same SPI serial flash controller as Cannon
Lake. Add Alder Lake-S PCI ID to the driver list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200925095109.51148-1-mika.westerberg@linux.intel.com
On my system the spi_nor_probe() took ~6 ms at bootup. That's not a
lot, but every little bit adds up to a slow bootup. While we can get
this out of the boot path by making it a module, there are times where
it is convenient (or even required) for this to be builtin the kernel.
Let's set that we prefer async probe so that we don't block other
drivers from probing while we are probing.
This is a tiny little change that is almost guaranteed to be safe for
anything that is able to run as a module, which SPI_NOR is.
Specifically modules are already probed asynchronously. Also: since
other things in the system may have enabled asynchronous probe the
system may already be doing other things during our probe.
There is a small possibility that some other driver that was a client
of SPI_NOR didn't handle -EPROBE_DEFER and was relying on probe
ordering and only worked when the SPI_NOR and the SPI bus were
builtin. In that case the other driver has a bug that's waiting to
hit and the other driver should be fixed.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200902160002.1.I658d1c0db9adfeb9a59bc55e96a19e192c959e55@changeid
Mechanical switch from the legacy "mode" enumeration to the new
"engine type" enumeration in drivers and board files.
The device tree parsing is also updated to return the new enumeration
from the old strings.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200827085208.16276-11-miquel.raynal@bootlin.com
The use of "syndrome" placement should not be encoded in the ECC
engine mode/type.
Create a "placement" field in NAND chip and change all occurrences of
the NAND_ECC_HW_SYNDROME enumeration to be just NAND_ECC_HW and
possibly a placement entry like NAND_ECC_PLACEMENT_INTERLEAVED.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200827085208.16276-10-miquel.raynal@bootlin.com
Set up a readahead size by default, as very few users have a good
reason to change it. This means code, ecryptfs, and orangefs now
set up the values while they were previously missing it, while ubifs,
mtd and vboxsf manually set it to 0 to avoid readahead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Acked-by: David Sterba <dsterba@suse.com> [btrfs]
Acked-by: Richard Weinberger <richard@nod.at> [ubifs, mtd]
Signed-off-by: Jens Axboe <axboe@kernel.dk>
A detach hung is possible when a race occurs between the detach process
and the ubi background thread. The following sequences outline the race:
ubi thread: if (list_empty(&ubi->works)...
ubi detach: set_bit(KTHREAD_SHOULD_STOP, &kthread->flags)
=> by kthread_stop()
wake_up_process()
=> ubi thread is still running, so 0 is returned
ubi thread: set_current_state(TASK_INTERRUPTIBLE)
schedule()
=> ubi thread will never be scheduled again
ubi detach: wait_for_completion()
=> hung task!
To fix that, we need to check kthread_should_stop() after we set the
task state, so the ubi thread will either see the stop bit and exit or
the task state is reset to runnable such that it isn't scheduled out
indefinitely.
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Cc: <stable@vger.kernel.org>
Fixes: 801c135ce7 ("UBI: Unsorted Block Images")
Reported-by: syzbot+853639d0cb16c31c7a14@syzkaller.appspotmail.com
Signed-off-by: Richard Weinberger <richard@nod.at>
As the only user has been removed in previous patch, let's revert
this one together.
This reverts commit be192209d5.
Reported-by: Matthias Weisser <m.weisser.m@gmail.com>
Suggested-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/1599205640-26690-2-git-send-email-yangyicong@hisilicon.com
Previous patch intends to restore the flash's QE bit when removed/shutdown,
but may have some problems and break the flash:
- for those originally in Quad mode, this patch will clear the QE bit
when unloaded the flash, which is incorrect.
- even with above problem solved, it may still break the flash as some
flash's QE bit is non-volatile and lots of set/reset will wear out
the bit.
- the restore method cannot be proved to be valid as if a hard
reset or accident crash happened, the spi_nor_restore() won't be
performed the the QE bit will not be restored as we expected to.
So let's revert it to fix this. The discussion can be found at [1].
This reverts commit cc59e6bb6c.
[1] https://lore.kernel.org/linux-mtd/CAO8h3eFLVLRmw7u+rurKsg7=Nh2q-HVq-HgVXig8gf5Dffk8MA@mail.gmail.com/
Reported-by: Matthias Weisser <m.weisser.m@gmail.com>
Suggested-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/1599205640-26690-1-git-send-email-yangyicong@hisilicon.com
Variable 'size' is being assigned the value zero that will never be
read. The assignment is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200910154451.752569-1-colin.king@canonical.com
If calling mtdoops_write, don't also schedule work to be done later.
Although this appears to not be causing an issue, possibly because the
scheduled work will never get done, it is confusing.
Fixes: 016c1291ce ("mtd: mtdoops: do not use mtd->panic_write directly")
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200903034217.23079-1-mark.tomlinson@alliedtelesis.co.nz
Create a generic ECC engine framework. This is a base to instantiate ECC
engine objects.
If we really want to be generic, bindings must evolve, so here is the
new logic. The following three properties are mutually exclusive:
- The nand-no-ecc-engine boolean property is set and there is no
ECC engine to retrieve.
- The nand-use-soft-ecc-engine boolean property is set and the core
will force using the use of software correction.
- There is a nand-ecc-engine property pointing at a node which will
act as ECC engine.
It the later case, the property may reference:
- The NAND chip node itself (for the on-die ECC case).
- The parent node if the NAND controller embeds an ECC engine.
- Any other node being an external ECC controller as well.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200827085208.16276-9-miquel.raynal@bootlin.com
Allows a mtdconcat's subdevice->_panic_write to be used for
capturing a mtdoops dump.
Note: The ->_panic_write is mapped through from the first chip
that is part of the concat virtual device.
Signed-off-by: Matthew Weber <matthew.weber@rockwellcollins.com>
[miquel.raynal@bootlin.com: return err, not void]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200602143403.13465-1-matthew.weber@rockwellcollins.com
Building lpddr2_nvm with clang can result in a giant stack usage
in one function:
drivers/mtd/lpddr/lpddr2_nvm.c:399:12: error: stack frame size of 1144 bytes in function 'lpddr2_nvm_probe' [-Werror,-Wframe-larger-than=]
The problem is that clang decides to build a copy of the mtd_info
structure on the stack and then do a memcpy() into the actual version. It
shouldn't really do it that way, but it's not strictly a bug either.
As a workaround, use a static const version of the structure to assign
most of the members upfront and then only set the few members that
require runtime knowledge at probe time.
Fixes: 96ba9dd657 ("mtd: lpddr: add driver for LPDDR2-NVM PCM memories")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200505140136.263461-1-arnd@arndb.de
In physmap_flash_of_init() the maps[].name can be populated based on the
optional 'linux,mtd-name' property in the dts. Make sure this is
retained when filling in the rest of the map[] data.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200824025744.25992-1-chris.packham@alliedtelesis.co.nz
Function print_drs_error is only used in drivers/mtd/lpddr/lpddr_cmds.c
so, better to move it there.
Also, notice that there's no need for inline as the function is used
once. Lastly, fix the following checkpatch warning:
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
+static void print_drs_error(unsigned dsr)
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/e0063cbd65f3b47be1db34efc494ea3047634d88.1588016644.git.gustavo@embeddedor.com
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yongqiang Liu <liuyongqiang13@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
JFFS2:
- Fix for a corner case while mounting
- Fix for an use-after-free issue
UBI:
- Fix for a memory load while attaching
- Don't produce an anchor PEB with fastmap being disabled
UBIFS:
- Fix for orphan inode logic
- Spelling fixes
- New mount option to specify filesystem version
-----BEGIN PGP SIGNATURE-----
iQJKBAABCAA0FiEEdgfidid8lnn52cLTZvlZhesYu8EFAl8xkPIWHHJpY2hhcmRA
c2lnbWEtc3Rhci5hdAAKCRBm+VmF6xi7wZJbD/9B5wLKRa0iG+LSiiY2WztnYKZ3
l4WjK+/2RbOxYPKuu+DaC2x8SpF0MHvk0mVcc03Az9R3xmzKHcC7OXszqHTJ0uet
JRvFMfLc2C7HoPHvcUQ+zT6bAZzZk/rUhd2uO6+7wHPb8ayqjOEVbDERKCOLOQsb
Z4HQyDuub7BcK554/9P4cUjX+mAcv6N4ILqIbofLq0OclZEceoH+6JlTFxElervO
X4Vfkiw6iZemqRZ118LnU6Ds0BG2sg0z7nlO6H6mBqRpR7iwHaBG88rqJrNyJlZN
9KPRXEUKnSXTzNVrOqHFkgbwpE1HZfVdIoiLW+ghrLBzVD7HmD1GM3wxYgpqh+jo
xXa6jU2RVH1va6YgjDB3qDekWqEDBoEMRnHOHaglViZvsH2BcIP8KUGVWAqHfPvv
AeraksbbVhQ8Vfa8lHAlGPq/kCAjDhdLOfc/clid2YSGZNuMoM5seSAbWD9dHWFR
KYzF+X11hh1BcGo8KttQHDjed3cMs9IuU9tXmBQy65W+ZYqDHU6NS53tN2YD4bbK
bS2Qd6EJUGQDPauxRxKHkwKODUC67sUA3GbGXBAmWhMdu5T2BAoU3jbU2NLtQiZa
yHOaiDDKwbQvpwcd1Ev1gIeihGfKEpt0T6zqABB3YxFtm9le4AEYyFKlhUXNTrX1
GwEhi9jtKznUzoW/CQ==
=iztS
-----END PGP SIGNATURE-----
Merge tag 'for-linus-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs
Pull JFFS2, UBI and UBIFS updates from Richard Weinberger:
"JFFS2:
- Fix for a corner case while mounting
- Fix for an use-after-free issue
UBI:
- Fix for a memory load while attaching
- Don't produce an anchor PEB with fastmap being disabled
UBIFS:
- Fix for orphan inode logic
- Spelling fixes
- New mount option to specify filesystem version"
* tag 'for-linus-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs:
jffs2: fix UAF problem
jffs2: fix jffs2 mounting failure
ubifs: Fix wrong orphan node deletion in ubifs_jnl_update|rename
ubi: fastmap: Free fastmap next anchor peb during detach
ubi: fastmap: Don't produce the initial next anchor PEB when fastmap is disabled
ubifs: misc.h: delete a duplicated word
ubifs: add option to specify version for new file systems
* Spelling
* http to https updates
NAND core changes:
* Drop useless 'depends on' in Kconfig
* Add an extra level in the Kconfig hierarchy
* Trivial spellings
* Dynamic allocation of the interface configurations
* Dropping the default ONFI timing mode
* Various cleanup (types, structures, naming, comments)
* Hide the chip->data_interface indirection
* Add the generic rb-gpios property
* Add the ->choose_interface_config() hook
* Introduce nand_choose_best_sdr_timings()
* Use default values for tPROG_max and tBERS_max
* Avoid redefining tR_max and tCCS_min
* Add a helper to find the closest ONFI mode
* bcm63xx MTD parsers: simplify CFE detection
Raw NAND controller drivers changes:
* fsl-upm: Deprecation of specific DT properties
* fsl_upm: Driver rework and cleanup in favor of ->exec_op()
* Ingenic: Cleanup ARRAY_SIZE() vs sizeof() use
* brcmnand: ECC error handling on EDU transfers
* brcmnand: Don't default to EDU transfers
* qcom: Set BAM mode only if not set already
* qcom: Avoid write to unavailable register
* gpio: Driver rework in favor of ->exec_op()
* tango: ->exec_op() conversion
* mtk: ->exec_op() conversion
Raw NAND chip drivers changes:
* toshiba: Implement ->choose_interface_config() for TH58NVG2S3HBAI4
* toshiba: Implement ->choose_interface_config() for TC58NVG0S3E
* toshiba: Implement ->choose_interface_config() for TC58TEG5DCLTA00
* hynix: Implement ->choose_interface_config() for H27UCG8T2ATR-BC
SPI NOR core changes:
* Disable Quad Mode in spi_nor_restore().
* Don't abort BFPT parsing when QER reserved value is used.
* Add support/update capabilities for few flashes.
* Drop s70fl01gs flash: it does not support RDSR(05h) which
is critical for erase/write.
* Merge the SPIMEM DTR bits in spi-nor/next to avoid conflicts
during the release cycle.
SPI NOR controller drivers changes:
* Move the cadence-quadspi driver to spi-mem. The series was
taken through the SPI tree. Merge it also in spi-nor/next
to avoid conflicts during the release cycle.
* intel-spi:
- Add new PCI IDs.
- Ignore the Write Disable command, the controller doesn't
support it.
- Fix performance regression.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl8vJtMACgkQJWrqGEe9
VoRdGAf/Y5m5BwmLilkEYpffyxi7dVR6XOKPLU5EJXkS3dPvH9398zchbHOdedCZ
OzJIfh6Iv+qbkgS2g0lAAT+SAfOfG9plubvSdkjrHXl4eZXRnR/49RF5LAEju7sz
Uw1HdRcawyEi5uI9yYS0tCeVMIUJq+5x7VibH+82yOIdSPc60c7FDc5ih/nVKj/a
Pn9LOzGzkdndcE1b3FcF2Uk/T1YOJx3Yt5ngALlPpJxaDZmQSHtYPuuz8DfUbamf
uj3CkpqYRyT18CzuFvtuba6LyF+donXNJgvl6ivW7dlRSPzSMnDQu7J5bpNhUfcd
p/ZdzX1Jxle4theDm0J9ALsSSM5g2w==
=RiY8
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd updates from Miquel Raynal:
"MTD core changes:
- Spelling
- http to https updates
NAND core changes:
- Drop useless 'depends on' in Kconfig
- Add an extra level in the Kconfig hierarchy
- Trivial spellings
- Dynamic allocation of the interface configurations
- Dropping the default ONFI timing mode
- Various cleanup (types, structures, naming, comments)
- Hide the chip->data_interface indirection
- Add the generic rb-gpios property
- Add the ->choose_interface_config() hook
- Introduce nand_choose_best_sdr_timings()
- Use default values for tPROG_max and tBERS_max
- Avoid redefining tR_max and tCCS_min
- Add a helper to find the closest ONFI mode
- bcm63xx MTD parsers: simplify CFE detection
Raw NAND controller drivers changes:
- fsl-upm: Deprecation of specific DT properties
- fsl_upm: Driver rework and cleanup in favor of ->exec_op()
- Ingenic: Cleanup ARRAY_SIZE() vs sizeof() use
- brcmnand: ECC error handling on EDU transfers
- brcmnand: Don't default to EDU transfers
- qcom: Set BAM mode only if not set already
- qcom: Avoid write to unavailable register
- gpio: Driver rework in favor of ->exec_op()
- tango: ->exec_op() conversion
- mtk: ->exec_op() conversion
Raw NAND chip drivers changes:
- toshiba: Implement ->choose_interface_config() for TH58NVG2S3HBAI4,
TC58NVG0S3E, and TC58TEG5DCLTA00
- hynix: Implement ->choose_interface_config() for H27UCG8T2ATR-BC
SPI NOR core changes:
- Disable Quad Mode in spi_nor_restore().
- Don't abort BFPT parsing when QER reserved value is used.
- Add support/update capabilities for few flashes.
- Drop s70fl01gs flash: it does not support RDSR(05h) which is
critical for erase/write.
- Merge the SPIMEM DTR bits in spi-nor/next to avoid conflicts during
the release cycle.
SPI NOR controller drivers changes:
- Move the cadence-quadspi driver to spi-mem. The series was taken
through the SPI tree. Merge it also in spi-nor/next to avoid
conflicts during the release cycle.
- intel-spi:
- Add new PCI IDs.
- Ignore the Write Disable command, the controller doesn't support
it.
- Fix performance regression"
* tag 'mtd/for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (79 commits)
MTD: pfow.h: drop a duplicated word
MTD: mtd-abi.h: drop a duplicated word
mtd: rawnand: omap_elm: Replace HTTP links with HTTPS ones
mtd: Replace HTTP links with HTTPS ones
mtd: hyperbus: Replace HTTP links with HTTPS ones
mtd: revert "spi-nor: intel: provide a range for poll_timout"
mtd: spi-nor: update read capabilities for w25q64 and s25fl064k
mtd: spi-nor: micron: Add SPI_NOR_DUAL_READ flag on mt25qu02g
mtd: spi-nor: macronix: Add support for mx66u2g45g
mtd: spi-nor: intel-spi: Simulate WRDI command
mtd: spi-nor: Disable the flash quad mode in spi_nor_restore()
mtd: spi-nor: Add capability to disable flash quad mode
mtd: spi-nor: spansion: Remove s70fl01gs from flash_info
mtd: spi-nor: sfdp: do not make invalid quad enable fatal
dt-bindings: mtd: fsl-upm-nand: Deprecate chip-delay and fsl, upm-wait-flags
mtd: rawnand: stm32_fmc2: get resources from parent node
mtd: rawnand: stm32_fmc2: use regmap APIs
memory: stm32-fmc2-ebi: add STM32 FMC2 EBI controller driver
dt-bindings: memory-controller: add STM32 FMC2 EBI controller documentation
dt-bindings: mtd: update STM32 FMC2 NAND controller documentation
...
Pull misc vfs updates from Al Viro:
"No common topic whatsoever in those, sorry"
* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fs: define inode flags using bit numbers
iov_iter: Move unnecessary inclusion of crypto/hash.h
dlmfs: clean up dlmfs_file_{read,write}() a bit
* Drop useless 'depends on' in Kconfig
* Add an extra level in the Kconfig hierarchy
* Trivial spellings
* Dynamic allocation of the interface configurations
* Dropping the default ONFI timing mode
* Various cleanup (types, structures, naming, comments)
* Hide the chip->data_interface indirection
* Add the generic rb-gpios property
* Add the ->choose_interface_config() hook
* Introduce nand_choose_best_sdr_timings()
* Use default values for tPROG_max and tBERS_max
* Avoid redefining tR_max and tCCS_min
* Add a helper to find the closest ONFI mode
* bcm63xx MTD parsers: simplify CFE detection
Raw NAND controller drivers changes:
* fsl-upm: Deprecation of specific DT properties
* fsl_upm: Driver rework and cleanup in favor of ->exec_op()
* Ingenic: Cleanup ARRAY_SIZE() vs sizeof() use
* brcmnand: ECC error handling on EDU transfers
* brcmnand: Don't default to EDU transfers
* qcom: Set BAM mode only if not set already
* qcom: Avoid write to unavailable register
* gpio: Driver rework in favor of ->exec_op()
* tango: ->exec_op() conversion
* mtk: ->exec_op() conversion
Raw NAND chip drivers changes:
* toshiba: Implement ->choose_interface_config() for TH58NVG2S3HBAI4
* toshiba: Implement ->choose_interface_config() for TC58NVG0S3E
* toshiba: Implement ->choose_interface_config() for TC58TEG5DCLTA00
* hynix: Implement ->choose_interface_config() for H27UCG8T2ATR-BC
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl8s85cACgkQJWrqGEe9
VoTrdwgAqphDYjtYNaI+1F0YQdIy/l8ddVmc5NwhKpiitKh0APDFDrdV5CwQaENO
9wWHJJPpT7xXPnEaq2+OWlPt2HpnEI4a+IRvySc9lr+MfkdY9ubo3B2wX7jBueKr
WoVDAGe8Ua1FkPOeDy7Qe+H1bQPha8fvyfb7x2h8uCYrrIkDJaMilorzHVnuXfCg
t5QJXRuznmYjUfMKOgLDjX3r79IJ+5mcrJIvMgHOyQIoG4Aao7lHIr2f01O50HWy
JKqQD3QhPR8lJGaEW485s+H+gnnNQW8Y1+8u3bhauEg/6Ddx2oksUIBTME8HUUuK
kAXrQ+KEs37l1a6pyaMBHaWU18T/oQ==
=hn04
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux into mtd/next
Core changes:
* Drop useless 'depends on' in Kconfig
* Add an extra level in the Kconfig hierarchy
* Trivial spellings
* Dynamic allocation of the interface configurations
* Dropping the default ONFI timing mode
* Various cleanup (types, structures, naming, comments)
* Hide the chip->data_interface indirection
* Add the generic rb-gpios property
* Add the ->choose_interface_config() hook
* Introduce nand_choose_best_sdr_timings()
* Use default values for tPROG_max and tBERS_max
* Avoid redefining tR_max and tCCS_min
* Add a helper to find the closest ONFI mode
* bcm63xx MTD parsers: simplify CFE detection
Raw NAND controller drivers changes:
* fsl-upm: Deprecation of specific DT properties
* fsl_upm: Driver rework and cleanup in favor of ->exec_op()
* Ingenic: Cleanup ARRAY_SIZE() vs sizeof() use
* brcmnand: ECC error handling on EDU transfers
* brcmnand: Don't default to EDU transfers
* qcom: Set BAM mode only if not set already
* qcom: Avoid write to unavailable register
* gpio: Driver rework in favor of ->exec_op()
* tango: ->exec_op() conversion
* mtk: ->exec_op() conversion
Raw NAND chip drivers changes:
* toshiba: Implement ->choose_interface_config() for TH58NVG2S3HBAI4
* toshiba: Implement ->choose_interface_config() for TC58NVG0S3E
* toshiba: Implement ->choose_interface_config() for TC58TEG5DCLTA00
* hynix: Implement ->choose_interface_config() for H27UCG8T2ATR-BC
A fairly quiet release for SPI, nothing really going on in the core
although there's been quite a bit of driver related activity. This pull
request includes the addition of some shared code in drivers/memory for
the Renesas RPC-IF which is used by a newly added SPI driver, the memory
subsystem doesn't seem to have a fixed maintainer at the minute and this
seemed like the most sensible way to get that hardware supported.
- Quite a few cleanups and optimizations for the Altera, Qualcomm GENI,
sun6i and lantiq drivers.
- Several more GPIO descriptor conversions.
- Move the Cadence QuadSPI driver from drivers/mtd to drivers/spi.
- New support for Mediatek MT8192 and Renesas RPC-IF, R8A7742 and
R8A774e1.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl8oBFoTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0P2UB/47NlDsAadOiOB0ZzPKdn4Nr5BLvUza
TP63gAsxD4BErzgf/p/0D8qUTZPzmlfA833gj9hkIavJlTmv3fGrH0XeHg2OuCJb
yhyw9pE7MPpnARVOJHz1MZkAT/dY+sF3TaUXysmymlvs6CLqRnsLTOwK2f92SeGH
ygpC4J1tfD961xWmv2Zt8wNuQXtH+JePLXeZFSx2ZkpToFT56QO6kFpWjVfDquY4
/F8bc7qyXX6FcsBYAG6Ly35OSxbPazVLkTaDWQr5V4TAD0DXw0NOyvxg2OccqE31
y1jjx3hn98sN73m/VLzlEOer4w9313K5BOISaN0z7TQSQ55XRZKe4EQj
=K1PB
-----END PGP SIGNATURE-----
Merge tag 'spi-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"A fairly quiet release for SPI, nothing really going on in the core
although there's been quite a bit of driver related activity.
This includes the addition of some shared code in drivers/memory for
the Renesas RPC-IF which is used by a newly added SPI driver, the
memory subsystem doesn't seem to have a fixed maintainer at the minute
and this seemed like the most sensible way to get that hardware
supported.
- Quite a few cleanups and optimizations for the Altera, Qualcomm
GENI, sun6i and lantiq drivers.
- Several more GPIO descriptor conversions.
- Move the Cadence QuadSPI driver from drivers/mtd to drivers/spi.
- New support for Mediatek MT8192 and Renesas RPC-IF, R8A7742 and
R8A774e1"
* tag 'spi-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (119 commits)
dt-bindings: lpspi: New property in document DT bindings for LPSPI
spi: lpspi: fix using CS discontinuously on i.MX8DXLEVK
spi: lpspi: remove unused fsl_lpspi->chipselect
spi: lpspi: Fix kernel warning dump when probe fail after calling spi_register
spi: rockchip: Fix error in SPI slave pio read
spi: rockchip: Support 64-location deep FIFOs
spi: rockchip: Config spi rx dma burst size depend on xfer length
spi: spi-topcliff-pch: drop call to wakeup-disable
spi: spidev: Align buffers for DMA
spi: correct kernel-doc inconsistency
spi: sun4i: update max transfer size reported
spi: imx: enable runtime pm support
spi: update bindings for MT8192 SoC
spi: mediatek: add spi support for mt8192 IC
spi: Add bindings for Lightning Mountain SoC
spi: lantiq: Add support to Lightning Mountain SoC
spi: lantiq: Move interrupt configuration to SoC specific data structure
spi: lantiq: Add fifo size bit mask in SoC specific data structure
spi: lantiq: Add support to acknowledge interrupt
spi: lantiq: Move interrupt control register offesets to SoC specific data structure
...
ubi_wl_entry related with the fm_next_anchor PEB is not freed during
detach, which causes a memory leak.
Don't forget to release fm_next_anchor PEB while detaching ubi from
mtd when CONFIG_MTD_UBI_FASTMAP is enabled.
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Fixes: 4b68bf9a69 ("ubi: Select fastmap anchor PEBs considering...")
Signed-off-by: Richard Weinberger <richard@nod.at>
Following process triggers a memleak caused by forgetting to release the
initial next anchor PEB (CONFIG_MTD_UBI_FASTMAP is disabled):
1. attach -> __erase_worker -> produce the initial next anchor PEB
2. detach -> ubi_fastmap_close (Do nothing, it should have released the
initial next anchor PEB)
Don't produce the initial next anchor PEB in __erase_worker() when fastmap
is disabled.
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Suggested-by: Sascha Hauer <s.hauer@pengutronix.de>
Fixes: f9c34bb529 ("ubi: Fix producing anchor PEBs")
Reported-by: syzbot+d9aab50b1154e3d163f5@syzkaller.appspotmail.com
Signed-off-by: Richard Weinberger <richard@nod.at>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
- Disable Quad Mode in spi_nor_restore().
- Don't abort BFPT parsing when QER reserved value is used.
- Add support/update capabilities for few flashes.
- Drop s70fl01gs flash: it does not support RDSR(05h) which
is critical for erase/write.
- Merge the SPIMEM DTR bits in spi-nor/next to avoid conflicts
during the release cycle.
SPI NOR controller drivers changes:
- Move the cadence-quadspi driver to spi-mem. The series was
taken through the SPI tree. Merge it also in spi-nor/next
to avoid conflicts during the release cycle.
- intel-spi:
- Add new PCI IDs.
- Ignore the Write Disable command, the controller doesn't
support it.
- Fix performance regression.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEHUIqys8OyG1eHf7fS1VPR6WNFOkFAl8f/IUACgkQS1VPR6WN
FOk8nQf/ReDFzgrZGPRXK8MbcWdmrNQo5cGwCs2zuKskvWMdgNZC92DTlgrMmx+d
NQ/0PpsOHZJ1bcPjlsxccSQNrFnSzxr91n8NJIQ6DuralCN+x9Zh4dtox0Q0WB1x
d9y+I65EpSyEHRhWRW1y2sq5xRlwiANWVQPfIUN10q/flz9CI5Q8gY8wdUQT4Q5x
/ER7CMSbZSehnxHnJ9kSFDRhJCobDKnOdsFLDVZFPseQZzXYe5zP0J/T5S63wem2
/QFKSCfcI4UqMbeurGpQok9ZywCUp+SUG2mAld/yTig+YCCeY1Dp45IGJZ7eKDky
NPYjVYaRlvWwcTgS1OdCThGd+F29Ug==
=YZOZ
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-5.9' of https://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux into mtd/next
SPI NOR core changes:
- Disable Quad Mode in spi_nor_restore().
- Don't abort BFPT parsing when QER reserved value is used.
- Add support/update capabilities for few flashes.
- Drop s70fl01gs flash: it does not support RDSR(05h) which
is critical for erase/write.
- Merge the SPIMEM DTR bits in spi-nor/next to avoid conflicts
during the release cycle.
SPI NOR controller drivers changes:
- Move the cadence-quadspi driver to spi-mem. The series was
taken through the SPI tree. Merge it also in spi-nor/next
to avoid conflicts during the release cycle.
- intel-spi:
- Add new PCI IDs.
- Ignore the Write Disable command, the controller doesn't
support it.
- Fix performance regression.
Both w25q64 and s25fl064k nor flash support QUAD and DUAL read
command, hence update the same in flash_info table.
This is tested on Broadcom Stingray SoC (bcm958742t).
s25fl064k and w25q64 share the same JEDEC ID. The search alg will
return the first hit, so s25fl064k even for the winbond parts. We
should differentiate between these flashes, but it's not in the
scope of this patch. Related discussion at:
Link: https://lore.kernel.org/patchwork/patch/628090/
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Link: https://lore.kernel.org/r/20200529071655.739-1-rayagonda.kokatanur@broadcom.com
[tudor.ambarus@microchip.com: Update commit message and indicate that
s25fl064k and w25q64 share the same JEDEC ID]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The Micron mt25qu02g supports both x2 and x4 transactions. Add the
SPI_NOR_DUAL_READ flag to its spi_nor_ids[] table entry.
Tested on Pensando SoC hardware with a cadence quadspi controller
via drivers/spi/spi-cadence-quadspi.c, in x2 mode at 50MHz.
- random data write, erase, read - verified erase operations
- random data write, read/compare - verified write/read operations
Signed-off-by: David Clear <dac2@pensando.io>
Acked-by: Shannon Nelson <snelson@pensando.io>
Link: https://lore.kernel.org/r/20200720163656.38006-3-dac2@pensando.io
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The Macronix mx66u2g45g is a 1.8V, 2Gbit (256MB) device that
supports x1, x2, or x4 operation.
Tested on Pensando SoC hardware with a cadence quadspi controller
via drivers/spi/spi-cadence-quadspi.c, in x2 mode at 50MHz.
- random data write, erase, read - verified erase operations
- random data write, read/compare - verified write/read operations
Signed-off-by: David Clear <dac2@pensando.io>
Acked-by: Shannon Nelson <snelson@pensando.io>
Link: https://lore.kernel.org/r/20200720163656.38006-2-dac2@pensando.io
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
After spi_nor_write_disable() return code checks were introduced in the
spi-nor front end intel-spi backend stopped to work because WRDI was never
supported and always failed.
Just pretend it was sucessful and ignore the command itself. HW sequencer
shall do the right thing automatically, while with SW sequencer we cannot
do it anyway, because the only tool we had was preopcode and it makes no
sense for WRDI.
Fixes: bce679e5ae ("mtd: spi-nor: Check for errors after each Register Operation")
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/282e1305-fd08-e446-1a22-eb4dff78cfb4@nokia.com
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
When doing a "write" ioctl call, properly check that we have permissions
to do so before copying anything from userspace or anything else so we
can "fail fast". This includes also covering the MEMWRITE ioctl which
previously missed checking for this.
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[rw: Fixed locking issue]
Signed-off-by: Richard Weinberger <richard@nod.at>
Using uninitialized_var() is dangerous as it papers over real bugs[1]
(or can in the future), and suppresses unrelated compiler warnings
(e.g. "unused variable"). If the compiler thinks it is uninitialized,
either simply initialize the variable or make compiler changes.
In preparation for removing[2] the[3] macro[4], remove all remaining
needless uses with the following script:
git grep '\buninitialized_var\b' | cut -d: -f1 | sort -u | \
xargs perl -pi -e \
's/\buninitialized_var\(([^\)]+)\)/\1/g;
s:\s*/\* (GCC be quiet|to make compiler happy) \*/$::g;'
drivers/video/fbdev/riva/riva_hw.c was manually tweaked to avoid
pathological white-space.
No outstanding warnings were found building allmodconfig with GCC 9.3.0
for x86_64, i386, arm64, arm, powerpc, powerpc64le, s390x, mips, sparc64,
alpha, and m68k.
[1] https://lore.kernel.org/lkml/20200603174714.192027-1-glider@google.com/
[2] https://lore.kernel.org/lkml/CA+55aFw+Vbj0i=1TGqCR5vQkCzWJ0QxK6CernOU6eedsudAixw@mail.gmail.com/
[3] https://lore.kernel.org/lkml/CA+55aFwgbgqhbp1fkxvRKEpzyR5J8n1vKT1VZdz9knmPuXhOeg@mail.gmail.com/
[4] https://lore.kernel.org/lkml/CA+55aFz2500WfbKXAx8s67wrm9=yVJu65TpLgN_ybYNv0VEOKA@mail.gmail.com/
Reviewed-by: Leon Romanovsky <leonro@mellanox.com> # drivers/infiniband and mlx4/mlx5
Acked-by: Jason Gunthorpe <jgg@mellanox.com> # IB
Acked-by: Kalle Valo <kvalo@codeaurora.org> # wireless drivers
Reviewed-by: Chao Yu <yuchao0@huawei.com> # erofs
Signed-off-by: Kees Cook <keescook@chromium.org>
If the flash's quad mode is enabled, it'll remain in the quad mode when
it's removed. If we drive the flash next time in Standard/Dual SPI mode,
the QE bit is not cleared and the function of flash's WP# and RESET#/HOLD#
have been switched to IO2 and IO3 and are not restored.
Disable the Quad mode in spi_nor_restore(), then the flash's QE bit will
be cleared when removed. This will make sure the flash always enter the
Standard/Dual SPI mode when loaded.
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/1594027356-19088-3-git-send-email-yangyicong@hisilicon.com
Previous we didn't provide a way to disable the flash's quad mode.
Which means we cannot do some cleanup works when to remove or
poweroff the flash, like what set 4-byte address mode does in
spi_nor_restore().
Add the capability to disable the flash quad mode, by introducing
an enable flag in the flash parameters quad_enable() hooks and
related functions.
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/1594027356-19088-2-git-send-email-yangyicong@hisilicon.com
The s70fl01gs is a dual die stack of two s25fl512s die with dedicated chip
select pins to each. Tested with the device and confirmed that is working
as two s25fl512s devices. The current device ID in the flash_info table
matches with s70fs01gs which does not work with current MTD (s70fs01gs
does not support RDSR(05h) which is critical for erase/write).
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@cypress.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200626051650.495-1-Takahiro.Kuwano@cypress.com
The Micron MT35XU512ABA flash does not support the quad enable bit. But
instead of programming the Quad Enable Require field to 000b ("Device
does not have a QE bit"), it is programmed to 111b ("Reserved").
While this is technically incorrect, it is not reason enough to abort
BFPT parsing. Instead, continue BFPT parsing and let flashes set it in
their fixup hooks.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200623183030.26591-12-p.yadav@ti.com
This MIPS driver does not support COMPILE_TEST yet and failed to build
under my radar.
Replace 'mtd' chich is not defined in the scope of xway_nand_remove()
by nand_to_mtd(chip). The mistake has been added in the long series
dropping nand_release().
Tested with a 7.3.0 MIPS GCC toolchain built with Buildroot.
Fixes: 9fdd78f7bc ("mtd: rawnand: xway: Stop using nand_release()")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200626065511.16424-1-miquel.raynal@bootlin.com
FMC2 EBI support has been added. Common resources (registers base
address and clock) can now be shared between the 2 drivers using
"st,stm32mp1-fmc2-nfc" compatible string. It means that the
common resources should now be found in the parent device when EBI
node is available.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1591975362-22009-7-git-send-email-christophe.kerello@st.com
A MDMA issue has been solved on Kernel 5.7. The effect of this fix is
that the MDMA driver is now deferred and the FMC2 NFC driver is also
deferred. All is working fine but there is a FMC2 log in the console:
stm32_fmc2_nfc 58002000.nand-controller: failed to request tx DMA
channel: -517
This patch removes the display of this log in the console in case of
this error is -EPROBE_DEFER.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1591975362-22009-2-git-send-email-christophe.kerello@st.com
The ARRAY_SIZE() is the number of elements but we want to use sizeof()
here for the number of bytes. Fortunately, they are the same thing
because it's an array of u8 so this has no effect on runtime.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200624132640.GC9972@mwanda
This chip is (nearly) identical to the Winbond w25q64 which is
already supported by Linux. Compared to the w25q64, the 'jvm'
has a different JEDEC ID.
Signed-off-by: Sven Van Asbroeck <thesven73@gmail.com>
[tudor.ambarus@microchip.com: Order entry alphabetically, update
subject, update Sven's email address]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200629195306.1030-1-TheSven73@gmail.com
The MX25R1635F is the smaller sibling of the MX25R3235F that is
already supported. It's only half the size (16Mb).
It was tested on the Kontron Electronics i.MX8MM SoM (N8010)
using raw read and write from and to the mtd device and
the 'flash_erase' command.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
[tudor.ambarus@microchip.com: update subject]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200702140523.6811-1-frieder.schrempf@kontron.de
The header file linux/uio.h includes crypto/hash.h which pulls in
most of the Crypto API. Since linux/uio.h is used throughout the
kernel this means that every tiny bit of change to the Crypto API
causes the entire kernel to get rebuilt.
This patch fixes this by moving it into lib/iov_iter.c instead
where it is actually used.
This patch also fixes the ifdef to use CRYPTO_HASH instead of just
CRYPTO which does not guarantee the existence of ahash.
Unfortunately a number of drivers were relying on linux/uio.h to
provide access to linux/slab.h. This patch adds inclusions of
linux/slab.h as detected by build failures.
Also skbuff.h was relying on this to provide a declaration for
ahash_request. This patch adds a forward declaration instead.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Intel Tiger Lake-H has the same SPI serial flash controller as Cannon
Lake. Add Tiger Lake-H PCI ID to the driver list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200624192103.78770-1-mika.westerberg@linux.intel.com
Intel Emmitsburg has the same SPI serial flash controller as Lewisburg.
Add Emmitsburg PCI ID to the driver list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200615155748.920-1-mika.westerberg@linux.intel.com
Instead of trying to parse CFE version string, which is customized by some
vendors, let's just check that "CFE1" was passed on argument 3.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200615091740.2958303-1-noltari@gmail.com
Implement ECC correctable and uncorrectable error handling for EDU
reads. If ECC correctable bitflips are encountered on EDU transfer,
read page again using PIO. This is needed due to a NAND controller
limitation where corrected data is not transferred to the DMA buffer
on ECC error. This applies to ECC correctable errors that are reported
by the controller hardware based on set number of bitflips threshold in
the controller threshold register, bitflips below the threshold are
corrected silently and are not reported by the controller hardware.
Fixes: a5d53ad26a ("mtd: rawnand: brcmnand: Add support for flash-edu for dma transfers")
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200612212902.21347-3-kdasu.kdev@gmail.com
When flash-dma is absent do not default to using flash-edu.
Make sure flash-edu is enabled before setting EDU transfer
function.
Fixes: a5d53ad26a ("mtd: rawnand: brcmnand: Add support for flash-edu for dma transfers")
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200612212902.21347-2-kdasu.kdev@gmail.com
BAM is DMA controller on QCOM ipq platforms, BAM mode on NAND driver
is set by writing BAM_MODE_EN bit on NAND_CTRL register.
NAND_CTRL is an operational register and in BAM mode operational
registers are read only.
So, before enabling BAM mode by writing the NAND_CTRL register, check
if BAM mode was already enabled by the bootloader, and enable BAM mode
only if it is not enabled already.
Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1591948696-16015-3-git-send-email-sivaprak@codeaurora.org
SFLASHC_BURST_CFG is only available on older ipq NAND platforms, this
register has been removed when the NAND controller got implemented in
the qpic controller.
Avoid writing this register on devices which are based on qpic NAND
controller.
Fixes: dce84760b0 ("mtd: nand: qcom: Support for IPQ8074 QPIC NAND controller")
Cc: stable@vger.kernel.org
Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1591948696-16015-2-git-send-email-sivaprak@codeaurora.org
Explicitly inherit from nand_controller instead of relying on the
nand_chip.legacy.dummy_controller field.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200603134922.1352340-8-boris.brezillon@collabora.com
The integer-based GPIO ids are now deprecated in favor of the GPIO desc
API. The PPC platforms have already been converted to GPIOLIB, so let's
use gpio descs in the NAND driver too.
While at it, we use devm_gpiod_get_index_optional() so we can get rid
of the manual gpio desc release done in the init error path and in the
remove function.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200603134922.1352340-7-boris.brezillon@collabora.com
Replace the of_address_to_resource() + devm_ioremap() calls by
platform_get_resource() + devm_ioremap_resource() ones which allows us
to get rid of one error message since devm_ioremap_resource() already
takes care of that.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200603134922.1352340-6-boris.brezillon@collabora.com
The mtd var in fun_wait_rnb() is now unused, let's get rid of it and
fix the warning resulting from this unused var.
Fixes: 50a487e771 ("mtd: rawnand: Pass a nand_chip object to chip->dev_ready()")
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200603134922.1352340-2-boris.brezillon@collabora.com
Instead of manipulating the statically allocated structure and copy
timings around, allocate one at identification time and save it in the
nand_chip structure once it has been initialized.
All NAND chips using the same interface configuration during reset and
startup, we define a helper to retrieve a single reset interface
configuration object, shared across all NAND chips.
We use a second pointer to always have a reference on the currently
applied interface configuration, which may either point to the "best
interface configuration" or to the "default reset interface
configuration".
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200529111322.7184-29-miquel.raynal@bootlin.com
The ->choose_interface() hook is here for manufacturer drivers to
provide a better timing interface than the default one, this field is
not needed anymore.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200529111322.7184-28-miquel.raynal@bootlin.com
The Kioxia/Toshiba TH58NVG2S3HBAI4 NAND memory is not ONFI compliant.
The timings of the NAND chip memory are quite close to ONFI mode 4 but
is breaking that spec.
By providing our own set of timings, erase block read speed is increased
from 6910 kiB/s to 13490 kiB/s and erase block write speed is increased
from 3350 kiB/s to 4410 kiB/s.
Tested on IMX6SX which has a NAND controller supporting EDO mode.
Signed-off-by: Rickard x Andersson <rickaran@axis.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200529111322.7184-27-miquel.raynal@bootlin.com
This hook can be overloaded by NAND manufacturer drivers to propose
alternative timings when not following the main standards. In this
case, the manufacturer drivers is responsible for choosing the best
interface configuration that fits both the controller and chip
capabilities.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200529111322.7184-23-miquel.raynal@bootlin.com
Extract the logic out of nand_choose_interface_config() to create a
public helper that can be reused by manufacturer drivers. Add the
possibility to provide a specific set of timings.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200529111322.7184-22-miquel.raynal@bootlin.com
Warn the user if the parameters are wrong but basically it would mean
there is a serious issue in the NAND core. So no need to ever check
its output, let's make this helper return void.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200529111322.7184-21-miquel.raynal@bootlin.com
The name/suffix data_interface is a bit misleading in that the field
or functions actually represent a configuration that can be applied by
the controller/chip. Let's rename all fields/functions/hooks that are
worth renaming.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
As a preparation for allocating the data interface structure
dynamically (and rename it), let's avoid accessing
chip->data_interface directly.
Instead, we introduce a helper, nand_get_interface_config(), and use
it to retrieve the current data interface configuration out of a
nand_chip object.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200529111322.7184-19-miquel.raynal@bootlin.com
The ONFI parameter page of a chip might define more fine grained
tPROG_max and tBERS_max. When we do not have this information, we
default to the highest possible values (they are maxima anyway).
There is no point setting these fields at runtime, so explicitly move
these defaults to the main ONFI SDR timings structure. This way, we
will also be able to return a pointer to mode 0 directly when we will
create a default reset configuration.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200529111322.7184-18-miquel.raynal@bootlin.com
These two values are already hardcoded in the default ONFI timing
structure, no need to redefine them here. Plus, we want to be able to
reference timing mode 0 easily and reliably, without extra
computation, so we get rid of the extra assignations.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200529111322.7184-17-miquel.raynal@bootlin.com
Vendors are allowed to provide their own set of timings. In this case,
we provide a way to derive the "closest" timing mode so that, if the
NAND controller does not support tweaking these parameters, it will be
able to configure itself anyway.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200529111322.7184-16-miquel.raynal@bootlin.com
Right now the core uses onfi_fill_data_interface() to initialize the
nand_data_interface object embedded in nand_chip, but we are about to
allocate this object dynamically and let manufacturer drivers provide
their own interface config. Let's patch the onfi_fill_data_interface()
so it can initialize an interface config that's not the one
currently attached to the nand_chip.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200529111322.7184-14-miquel.raynal@bootlin.com
This name is a bit misleading, what we do in this helper is trying to
find the best SDR timings supported by the controller and the chip.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200529111322.7184-12-miquel.raynal@bootlin.com
The data interface setup does not care about the default timing mode
but cares about the actual timing mode at the time of the call of this
helper.
Use this entry instead and let chip->default_timing_mode only be used
at initialization time.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200529111322.7184-9-miquel.raynal@bootlin.com
Avoid relying just on the default timing mode to discriminate if the
data interface must be restored. This field should only be used
at initialization time by legacy chips statically defined. Do a
memcmp() instead.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200529111322.7184-8-miquel.raynal@bootlin.com
It is currently called nand_manufacturer but could actually be called
nand_manufacturer_desc, like its instances, so that the former name is
left unused for now.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200529111322.7184-5-miquel.raynal@bootlin.com
Both OneNAND and raw NAND bits can't be compiled if MTD is disabled
because of the if/endif logic in drivers/mtd/Kconfig. There is no need
for an extra "depends on MTD" in their respective Kconfig files.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200529002517.3546-12-miquel.raynal@bootlin.com
Now that cadence-quadspi has been converted to use spi-mem framework,
move it under drivers/spi/
Update license header to match SPI subsystem style
Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200601070444.16923-9-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Move cadence-quadspi driver to use spi-mem framework. This is required
to make the driver support for SPI NAND flashes in future.
Driver is feature compliant with existing SPI NOR version.
Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200601070444.16923-8-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Drop redundant WREN command in cqspi_erase() as SPI NOR core takes care
of sending WREN command before sending erase command.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200601070444.16923-7-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
dma_request_chan_by_mask() can throw EPROBE_DEFER if DMA provider
is not yet probed. Currently driver just falls back to using PIO mode
(which is less efficient) in this case. Instead return probe deferral
error as is so that driver will be re probed once DMA provider is
available.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200601070444.16923-6-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Make sure to undo the prior changes done by the driver when exiting due
to failure to acquire reset lines.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200601070444.16923-5-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If driver fails to acquire DMA channel then don't initialize
rx_dma_complete struct as it won't be used.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200601070444.16923-4-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently direct access mode is used on platforms that have AHB window
(memory mapped window) larger than flash size. This feature is limited
to TI platforms as non TI platforms have < 1MB of AHB window.
Therefore introduce a driver quirk to disable DAC mode and set it for
non TI compatibles. This is in preparation to move to spi-mem framework
where flash geometry cannot be known.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200601070444.16923-3-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Drop configuration of Flash size, erase size and page size
configuration. Flash size is needed only if using AHB decoder (BIT 23 of
CONFIG_REG) which is not used by the driver.
Erase size and page size are needed if IP is configured to send WREN
automatically. But since SPI NOR layer takes care of sending WREN, there
is no need to configure these fields either.
Therefore drop these in preparation to move the driver to spi-mem
framework where flash geometry is not visible to controller driver.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200601070444.16923-2-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Check and set master panic write flag so that low level drivers
can use it to take required action to ensure oops data gets written
to assigned mtdoops device partition.
Fixes: 9f897bfdd8 ("mtd: Add flag to indicate panic_write")
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200615155134.32007-1-kdasu.kdev@gmail.com
* partition parser: Support MTD names containing one or more colons.
* mtdblock: clear cache_state to avoid writing to bad blocks repeatedly.
Raw NAND core changes:
* Stop using nand_release(), patched all drivers.
* Give more information about the ECC weakness when not matching the
chip's requirement.
* MAINTAINERS updates.
* Support emulated SLC mode on MLC NANDs.
* Support "constrained" controllers, adapt the core and ONFI/JEDEC
table parsing and Micron's code.
* Take check_only into account.
* Add an invalid ECC mode to discriminate with valid ones.
* Return an enum from of_get_nand_ecc_algo().
* Drop OOB_FIRST placement scheme.
* Introduce nand_extract_bits().
* Ensure a consistent bitflips numbering.
* BCH lib:
- Allow easy bit swapping.
- Rework a little bit the exported function names.
* Fix nand_gpio_waitrdy().
* Propage CS selection to sub operations.
* Add a NAND_NO_BBM_QUIRK flag.
* Give the possibility to verify a read operation is supported.
* Add a helper to check supported operations.
* Avoid indirect access to ->data_buf().
* Rename the use_bufpoi variables.
* Fix comments about the use of bufpoi.
* Rename a NAND chip option.
* Reorder the nand_chip->options flags.
* Translate obscure bitfields into readable macros.
* Timings:
- Fix default values.
- Add mode information to the timings structure.
Raw NAND controller driver changes:
* Fixed many error paths.
* Arasan
- New driver
* Au1550nd:
- Various cleanups
- Migration to ->exec_op()
* brcmnand:
- Misc cleanup.
- Support v2.1-v2.2 controllers.
- Remove unused including <linux/version.h>.
- Correctly verify erased pages.
- Fix Hamming OOB layout.
* Cadence
- Make cadence_nand_attach_chip static.
* Cafe:
- Set the NAND_NO_BBM_QUIRK flag
* cmx270:
- Remove this controller driver.
* cs553x:
- Misc cleanup
- Migration to ->exec_op()
* Davinci:
- Misc cleanup.
- Migration to ->exec_op()
* Denali:
- Add more delays before latching incoming data
* Diskonchip:
- Misc cleanup
- Migration to ->exec_op()
* Fsmc:
- Change to non-atomic bit operations.
* GPMI:
- Use nand_extract_bits()
- Fix runtime PM imbalance.
* Ingenic:
- Migration to exec_op()
- Fix the RB gpio active-high property on qi, lb60
- Make qi_lb60_ooblayout_ops static.
* Marvell:
- Misc cleanup and small fixes
* Nandsim:
- Fix the error paths, driver wide.
* Omap_elm:
- Fix runtime PM imbalance.
* STM32_FMC2:
- Misc cleanups (error cases, comments, timeout valus, cosmetic
changes).
SPI NOR core changes:
* Add, update support and fix few flashes.
* Prepare BFPT parsing for JESD216 rev D.
* Kernel doc fixes.
CFI changes:
* Support the absence of protection registers for Intel CFI flashes.
* Replace zero-length array with flexible-arrays.
-----BEGIN PGP SIGNATURE-----
iQJKBAABCAA0FiEEdgfidid8lnn52cLTZvlZhesYu8EFAl7f8msWHHJpY2hhcmRA
c2lnbWEtc3Rhci5hdAAKCRBm+VmF6xi7wXhlEADO3dfrWS9bsbZokuMppHlOTAsm
d0hPexu0ztRYr2qWgXScENtrcJ/0ygDPxEQxwIiWYAqwFn6yOBbum+tOo25edbEH
hGpkV5551vc48vD55nvxdoyWiJAgx93jVmfXU/Ad8EBDV4wGTBwzJJvZ8bxovUIl
Ccs9p8KU/Z5c7yNhYtLOJChU3gfMS0WS5iQakSnnT82TFJIdC8d8Y+bjupRfvHbz
ZkEC44Y+QcvSX6C2PJ2U9ScBf6r6WZkHmpOef8UzrxdLRvnhU16u9yRlepsm2D+x
KycQ81KPBhagLI+9AWGZQYma5GH0z+40LmhxR6YBS0ipS2lAc1wM904KB8RGohfl
SY4EYQSyx2/42bLEgR823rCfIIrzzNvjwnWdcZik2p2IWsocpzhdW2Fe3eJ7ULUe
9toQMg8JObawyKw7vRJtdiiX/OsNNv53FJsRu6rHkq3kgLXcmAUQYMh02LQFAkD6
gT8W8wmseZixI6mnG7tV2KHtRU70xWTTwJgFp5FvvBAP0p7KfbIlgJ0XrzQor2vB
3Jhb7e2DrOfu2RatZ12bmQpvpoU1Jv1U81UNnwsNpXawCPuRUYG3KCt+hjjr7HiV
++7YZ01pQ1GQ/pgcprwwKcpw5iTah0uXUEnE6pVbyX7hxg+OBgsWh8SK9MZMUioM
3yUGbotWAu2j6uM46g==
=2M9Y
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Richard Weinberger:
"MTD core changes:
- partition parser: Support MTD names containing one or more colons.
- mtdblock: clear cache_state to avoid writing to bad blocks
repeatedly.
Raw NAND core changes:
- Stop using nand_release(), patched all drivers.
- Give more information about the ECC weakness when not matching the
chip's requirement.
- MAINTAINERS updates.
- Support emulated SLC mode on MLC NANDs.
- Support "constrained" controllers, adapt the core and ONFI/JEDEC
table parsing and Micron's code.
- Take check_only into account.
- Add an invalid ECC mode to discriminate with valid ones.
- Return an enum from of_get_nand_ecc_algo().
- Drop OOB_FIRST placement scheme.
- Introduce nand_extract_bits().
- Ensure a consistent bitflips numbering.
- BCH lib:
- Allow easy bit swapping.
- Rework a little bit the exported function names.
- Fix nand_gpio_waitrdy().
- Propage CS selection to sub operations.
- Add a NAND_NO_BBM_QUIRK flag.
- Give the possibility to verify a read operation is supported.
- Add a helper to check supported operations.
- Avoid indirect access to ->data_buf().
- Rename the use_bufpoi variables.
- Fix comments about the use of bufpoi.
- Rename a NAND chip option.
- Reorder the nand_chip->options flags.
- Translate obscure bitfields into readable macros.
- Timings:
- Fix default values.
- Add mode information to the timings structure.
Raw NAND controller driver changes:
- Fixed many error paths.
- Arasan
- New driver
- Au1550nd:
- Various cleanups
- Migration to ->exec_op()
- brcmnand:
- Misc cleanup.
- Support v2.1-v2.2 controllers.
- Remove unused including <linux/version.h>.
- Correctly verify erased pages.
- Fix Hamming OOB layout.
- Cadence
- Make cadence_nand_attach_chip static.
- Cafe:
- Set the NAND_NO_BBM_QUIRK flag
- cmx270:
- Remove this controller driver.
- cs553x:
- Misc cleanup
- Migration to ->exec_op()
- Davinci:
- Misc cleanup.
- Migration to ->exec_op()
- Denali:
- Add more delays before latching incoming data
- Diskonchip:
- Misc cleanup
- Migration to ->exec_op()
- Fsmc:
- Change to non-atomic bit operations.
- GPMI:
- Use nand_extract_bits()
- Fix runtime PM imbalance.
- Ingenic:
- Migration to exec_op()
- Fix the RB gpio active-high property on qi, lb60
- Make qi_lb60_ooblayout_ops static.
- Marvell:
- Misc cleanup and small fixes
- Nandsim:
- Fix the error paths, driver wide.
- Omap_elm:
- Fix runtime PM imbalance.
- STM32_FMC2:
- Misc cleanups (error cases, comments, timeout valus, cosmetic
changes).
SPI NOR core changes:
- Add, update support and fix few flashes.
- Prepare BFPT parsing for JESD216 rev D.
- Kernel doc fixes.
CFI changes:
- Support the absence of protection registers for Intel CFI flashes.
- Replace zero-length array with flexible-arrays"
* tag 'mtd/for-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (208 commits)
mtd: clear cache_state to avoid writing to bad blocks repeatedly
mtd: parser: cmdline: Support MTD names containing one or more colons
mtd: physmap_of_gemini: remove defined but not used symbol 'syscon_match'
mtd: rawnand: Add an invalid ECC mode to discriminate with valid ones
mtd: rawnand: Return an enum from of_get_nand_ecc_algo()
mtd: rawnand: Drop OOB_FIRST placement scheme
mtd: rawnand: Avoid a typedef
mtd: Fix typo in mtd_ooblayout_set_databytes() description
mtd: rawnand: Stop using nand_release()
mtd: rawnand: nandsim: Reorganize ns_cleanup_module()
mtd: rawnand: nandsim: Rename a label in ns_init_module()
mtd: rawnand: nandsim: Manage lists on error in ns_init_module()
mtd: rawnand: nandsim: Fix the label pointing on nand_cleanup()
mtd: rawnand: nandsim: Free erase_block_wear on error
mtd: rawnand: nandsim: Use an additional label when freeing the nandsim object
mtd: rawnand: nandsim: Stop using nand_release()
mtd: rawnand: nandsim: Free the partition names in ns_free()
mtd: rawnand: nandsim: Free the allocated device on error in ns_init()
mtd: rawnand: nandsim: Free partition names on error in ns_init()
mtd: rawnand: nandsim: Fix the two ns_alloc_device() error paths
...
The include/linux/pgtable.h is going to be the home of generic page table
manipulation functions.
Start with moving asm-generic/pgtable.h to include/linux/pgtable.h and
make the latter include asm/pgtable.h.
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Cain <bcain@codeaurora.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Ungerer <gerg@linux-m68k.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Guo Ren <guoren@kernel.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Nick Hu <nickhu@andestech.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vincent Chen <deanbo422@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Will Deacon <will@kernel.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Link: http://lkml.kernel.org/r/20200514170327.31389-3-rppt@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The function call process is as follows:
mtd_blktrans_work()
while (1)
do_blktrans_request()
mtdblock_writesect()
do_cached_write()
write_cached_data() /*if cache_state is STATE_DIRTY*/
erase_write()
write_cached_data() returns failure without modifying cache_state
and cache_offset. So when do_cached_write() is called again,
write_cached_data() will be called again to perform erase_write()
on the same cache_offset.
But if this cache_offset points to a bad block, erase_write() will
always return -EIO. Writing to this mtdblk is equivalent to losing
the current data, and repeatedly writing to the bad block.
Repeatedly writing a bad block has no real benefits,
but brings some negative effects:
1 Lost subsequent data
2 Loss of flash device life
3 erase_write() bad blocks are very time-consuming. For example:
the function do_erase_oneblock() in chips/cfi_cmdset_0020.c or
chips/cfi_cmdset_0002.c may take more than 20 seconds to return
Therefore, when erase_write() returns -EIO in write_cached_data(),
clear cache_state to avoid writing to bad blocks repeatedly.
Signed-off-by: Xiaoming Ni <nixiaoming@huawei.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Looks like some drivers define MTD names with a colon in it, thus
making mtdpart= parsing impossible. Let's fix the parser to gracefully
handle that case: the last ':' in a partition definition sequence is
considered instead of the first one.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Ron Minnich <rminnich@google.com>
Tested-by: Ron Minnich <rminnich@google.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
It's not used by anyone now, remove it. Fix the following gcc warning:
drivers/mtd/maps/physmap-gemini.c:49:34: warning: ‘syscon_match’ defined
but not used [-Wunused-const-variable=]
static const struct of_device_id syscon_match[] = {
^~~~~~~~~~~~
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
* Support the absence of protection registers for Intel CFI flashes
* Replace zero-length array with flexible-arrays
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEEyRC2zAhGcGjrhiNExEYeRXyRFuMFAl7M2JMQHHZpZ25lc2hy
QHRpLmNvbQAKCRDERh5FfJEW4wPtB/9yqMGejoFX8QLvtFLBCH9XZhuxRSXH3qCO
JXaqIrGSPBA3zb3po8z7dN5PoKUFQStXL8KrP1XcYKnZCE5l5p1qeSeYh3pBBmuN
eWuNCTwEco6h0SSjEw/AWjJ47MhV9Cp+vg7KmozLR1zrg+DJvdeURA0cj/DI5gNL
9DQDlxS7+WuejFAwYEKajDvrYZRqUF/XrfUtPxg9mrXsrwf0iPSra0zZ9ia+qZbE
sYw9EXngnf3NmSfrDQ0Y+g3ViqxTZBhrFN8MDnn/L3rCCv7llGxm0aC4mPWN5BRx
pinhIfFWZMgMSdvRG9sLN4qOT1SDRGG5HYpR67LGsObAFLnMGWS+
=jReG
-----END PGP SIGNATURE-----
Merge tag 'cfi/for-5.8' of gitolite.kernel.org:pub/scm/linux/kernel/git/mtd/linux into mtd/next
CFI changes:
* Support the absence of protection registers for Intel CFI flashes
* Replace zero-length array with flexible-arrays
-----BEGIN PGP SIGNATURE-----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=HYf4
-----END PGP SIGNATURE-----
Merge tag 'for-5.8/block-2020-06-01' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
"Core block changes that have been queued up for this release:
- Remove dead blk-throttle and blk-wbt code (Guoqing)
- Include pid in blktrace note traces (Jan)
- Don't spew I/O errors on wouldblock termination (me)
- Zone append addition (Johannes, Keith, Damien)
- IO accounting improvements (Konstantin, Christoph)
- blk-mq hardware map update improvements (Ming)
- Scheduler dispatch improvement (Salman)
- Inline block encryption support (Satya)
- Request map fixes and improvements (Weiping)
- blk-iocost tweaks (Tejun)
- Fix for timeout failing with error injection (Keith)
- Queue re-run fixes (Douglas)
- CPU hotplug improvements (Christoph)
- Queue entry/exit improvements (Christoph)
- Move DMA drain handling to the few drivers that use it (Christoph)
- Partition handling cleanups (Christoph)"
* tag 'for-5.8/block-2020-06-01' of git://git.kernel.dk/linux-block: (127 commits)
block: mark bio_wouldblock_error() bio with BIO_QUIET
blk-wbt: rename __wbt_update_limits to wbt_update_limits
blk-wbt: remove wbt_update_limits
blk-throttle: remove tg_drain_bios
blk-throttle: remove blk_throtl_drain
null_blk: force complete for timeout request
blk-mq: drain I/O when all CPUs in a hctx are offline
blk-mq: add blk_mq_all_tag_iter
blk-mq: open code __blk_mq_alloc_request in blk_mq_alloc_request_hctx
blk-mq: use BLK_MQ_NO_TAG in more places
blk-mq: rename BLK_MQ_TAG_FAIL to BLK_MQ_NO_TAG
blk-mq: move more request initialization to blk_mq_rq_ctx_init
blk-mq: simplify the blk_mq_get_request calling convention
blk-mq: remove the bio argument to ->prepare_request
nvme: force complete cancelled requests
blk-mq: blk-mq: provide forced completion method
block: fix a warning when blkdev.h is included for !CONFIG_BLOCK builds
block: blk-crypto-fallback: remove redundant initialization of variable err
block: reduce part_stat_lock() scope
block: use __this_cpu_add() instead of access by smp_processor_id()
...
There is a risk that the fastmap anchor PEB is alternating between
just two PEBs, the current anchor and the previous anchor that was just
deleted. As the fastmap pools gets the first take on free PEBs, the
pools may leave no free PEBs to be selected as the new anchor,
resulting in the two PEBs alternating behaviour. If the anchor PEBs gets
a high erase count the PEBs will not be used by the pools but remain in
ubi->free, even more increasing the likelihood they will be used as
anchors.
Getting stuck using only a couple of PEBs continuously will result in an
uneven wear, eventually leading to failure.
To fix this:
- Choose the fastmap anchor when the most free PEBs are available. This is
during rebuilding of the fastmap pools, after the unused pool PEBs are
added to ubi->free but before the pools are populated again from the
free PEBs. Also reserve an additional second best PEB as a candidate
for the next time the fast map anchor is updated. If a better PEB is
found the next time the fast map anchor is updated, the candidate is
made available for building the pools.
- Enable anchor move within the anchor area again as it is useful for
distributing wear.
- The anchor candidate for the next fastmap update is the most suited free
PEB. Check this PEB's erase count during wear leveling. If the wear
leveling limit is exceeded, the PEB is considered unsuitable for now. As
all other non used anchor area PEBs should be even worse, free up the
used anchor area PEB with the lowest erase count.
Signed-off-by: Arne Edholm <arne.edholm@axis.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
- refactor pstore locking for safer module unloading (Kees Cook)
- remove orphaned records from pstorefs when backend unloaded (Kees Cook)
- refactor dump_oops parameter into max_reason (Pavel Tatashin)
- introduce pstore/zone for common code for contiguous storage (WeiXiong Liao)
- introduce pstore/blk for block device backend (WeiXiong Liao)
- introduce mtd backend (WeiXiong Liao)
-----BEGIN PGP SIGNATURE-----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=7s1u
-----END PGP SIGNATURE-----
Merge tag 'pstore-v5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull pstore updates from Kees Cook:
"Fixes and new features for pstore.
This is a pretty big set of changes (relative to past pstore pulls),
but it has been in -next for a while. The biggest change here is the
ability to support a block device as a pstore backend, which has been
desired for a while. A lot of additional fixes and refactorings are
also included, mostly in support of the new features.
- refactor pstore locking for safer module unloading (Kees Cook)
- remove orphaned records from pstorefs when backend unloaded (Kees
Cook)
- refactor dump_oops parameter into max_reason (Pavel Tatashin)
- introduce pstore/zone for common code for contiguous storage
(WeiXiong Liao)
- introduce pstore/blk for block device backend (WeiXiong Liao)
- introduce mtd backend (WeiXiong Liao)"
* tag 'pstore-v5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (35 commits)
mtd: Support kmsg dumper based on pstore/blk
pstore/blk: Introduce "best_effort" mode
pstore/blk: Support non-block storage devices
pstore/blk: Provide way to query pstore configuration
pstore/zone: Provide way to skip "broken" zone for MTD devices
Documentation: Add details for pstore/blk
pstore/zone,blk: Add ftrace frontend support
pstore/zone,blk: Add console frontend support
pstore/zone,blk: Add support for pmsg frontend
pstore/blk: Introduce backend for block devices
pstore/zone: Introduce common layer to manage storage zones
ramoops: Add "max-reason" optional field to ramoops DT node
pstore/ram: Introduce max_reason and convert dump_oops
pstore/platform: Pass max_reason to kmesg dump
printk: Introduce kmsg_dump_reason_str()
printk: honor the max_reason field in kmsg_dumper
printk: Collapse shutdown types into a single dump reason
pstore/ftrace: Provide ftrace log merging routine
pstore/ram: Refactor ftrace buffer merging
pstore/ram: Refactor DT size parsing
...
- add, update support and fix few flashes
- prepare BFPT parsing for JESD216 rev D
- kernel doc fixes
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEHUIqys8OyG1eHf7fS1VPR6WNFOkFAl7U4hUACgkQS1VPR6WN
FOkAjAf+Kxt87QGIOyQRybAhCJvHxRSiba+axmsM6dSn6+GoAPLRcxeW3fXOark6
gPlmY31+yFyGAGcUO/w51woc/NS4vicRhW+bxzcf/DSl88UJCZyr+G7QP14dcjQY
Zts2+sa44tdmo+DdxKUxfs4t9xQFNXIvM2Y1Rlb8KsJGKP4xLyXs0R6a4Xgo5qEX
wtMe2D+DoQ5rlnv98bDoaeRGkhq+n1aqt0zPLKHit1wcOEH7PseiwaKDIPhbTW0K
sIdSrzEb8aEzVt9pLuRig9NLFlwYK7mpfjdnOoR5oKTl1nQI44hBjAU/dnTL67YP
Bt/WNTaSwj/6XGhYA55+zxn5rJ3pQQ==
=w6a9
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux into mtd/next
SPI NOR core changes:
- add, update support and fix few flashes
- prepare BFPT parsing for JESD216 rev D
- kernel doc fixes
* Stop using nand_release(), patched all drivers.
* Give more information about the ECC weakness when not matching the
chip's requirement.
* MAINTAINERS updates.
* Support emulated SLC mode on MLC NANDs.
* Support "constrained" controllers, adapt the core and ONFI/JEDEC
table parsing and Micron's code.
* Take check_only into account.
* Add an invalid ECC mode to discriminate with valid ones.
* Return an enum from of_get_nand_ecc_algo().
* Drop OOB_FIRST placement scheme.
* Introduce nand_extract_bits().
* Ensure a consistent bitflips numbering.
* BCH lib:
- Allow easy bit swapping.
- Rework a little bit the exported function names.
* Fix nand_gpio_waitrdy().
* Propage CS selection to sub operations.
* Add a NAND_NO_BBM_QUIRK flag.
* Give the possibility to verify a read operation is supported.
* Add a helper to check supported operations.
* Avoid indirect access to ->data_buf().
* Rename the use_bufpoi variables.
* Fix comments about the use of bufpoi.
* Rename a NAND chip option.
* Reorder the nand_chip->options flags.
* Translate obscure bitfields into readable macros.
* Timings:
- Fix default values.
- Add mode information to the timings structure.
Raw NAND controller driver changes:
* Fixed many error paths.
* Arasan
- New driver
* Au1550nd:
- Various cleanups
- Migration to ->exec_op()
* brcmnand:
- Misc cleanup.
- Support v2.1-v2.2 controllers.
- Remove unused including <linux/version.h>.
- Correctly verify erased pages.
- Fix Hamming OOB layout.
* Cadence
- Make cadence_nand_attach_chip static.
* Cafe:
- Set the NAND_NO_BBM_QUIRK flag
* cmx270:
- Remove this controller driver.
* cs553x:
- Misc cleanup
- Migration to ->exec_op()
* Davinci:
- Misc cleanup.
- Migration to ->exec_op()
* Denali:
- Add more delays before latching incoming data
* Diskonchip:
- Misc cleanup
- Migration to ->exec_op()
* Fsmc:
- Change to non-atomic bit operations.
* GPMI:
- Use nand_extract_bits()
- Fix runtime PM imbalance.
* Ingenic:
- Migration to exec_op()
- Fix the RB gpio active-high property on qi, lb60
- Make qi_lb60_ooblayout_ops static.
* Marvell:
- Misc cleanup and small fixes
* Nandsim:
- Fix the error paths, driver wide.
* Omap_elm:
- Fix runtime PM imbalance.
* STM32_FMC2:
- Misc cleanups (error cases, comments, timeout valus, cosmetic
changes).
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl7TdZMACgkQJWrqGEe9
VoRthQgAttWsImXpEUa8C8CXvPhjpb6uZ7QYM4PSE0bheuVi7ivoDPyYWopno30h
R6UntGbsBqPyvDFDUxUEvyvn5F0JQK1dLif+7X0Ki5on6LkYdEuanHaSMZmSIXD8
atNhLVO1FeD3EulN8Dw9hGy6OrNT8O2bESbiJrCpOk9s6yAPINhKqZVJsyShcTs5
tc94/J0DIF7og8cdH4wYoz+AWw0WaHvPsn5VWnTy08gk7dB7hsq/DeftZmrJLL0g
B7Et1pvcLBSNBGBpzS6rEjXb/e3+wdKnNy0AQvrMdEZUzN3h9aY5sCLSFOsFfKQ+
xjxJgmyoKk0C9uCeNaPt8c7gTgAZAA==
=Gz6y
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux into mtd/next
Raw NAND core changes:
* Stop using nand_release(), patched all drivers.
* Give more information about the ECC weakness when not matching the
chip's requirement.
* MAINTAINERS updates.
* Support emulated SLC mode on MLC NANDs.
* Support "constrained" controllers, adapt the core and ONFI/JEDEC
table parsing and Micron's code.
* Take check_only into account.
* Add an invalid ECC mode to discriminate with valid ones.
* Return an enum from of_get_nand_ecc_algo().
* Drop OOB_FIRST placement scheme.
* Introduce nand_extract_bits().
* Ensure a consistent bitflips numbering.
* BCH lib:
- Allow easy bit swapping.
- Rework a little bit the exported function names.
* Fix nand_gpio_waitrdy().
* Propage CS selection to sub operations.
* Add a NAND_NO_BBM_QUIRK flag.
* Give the possibility to verify a read operation is supported.
* Add a helper to check supported operations.
* Avoid indirect access to ->data_buf().
* Rename the use_bufpoi variables.
* Fix comments about the use of bufpoi.
* Rename a NAND chip option.
* Reorder the nand_chip->options flags.
* Translate obscure bitfields into readable macros.
* Timings:
- Fix default values.
- Add mode information to the timings structure.
Raw NAND controller driver changes:
* Fixed many error paths.
* Arasan
- New driver
* Au1550nd:
- Various cleanups
- Migration to ->exec_op()
* brcmnand:
- Misc cleanup.
- Support v2.1-v2.2 controllers.
- Remove unused including <linux/version.h>.
- Correctly verify erased pages.
- Fix Hamming OOB layout.
* Cadence
- Make cadence_nand_attach_chip static.
* Cafe:
- Set the NAND_NO_BBM_QUIRK flag
* cmx270:
- Remove this controller driver.
* cs553x:
- Misc cleanup
- Migration to ->exec_op()
* Davinci:
- Misc cleanup.
- Migration to ->exec_op()
* Denali:
- Add more delays before latching incoming data
* Diskonchip:
- Misc cleanup
- Migration to ->exec_op()
* Fsmc:
- Change to non-atomic bit operations.
* GPMI:
- Use nand_extract_bits()
- Fix runtime PM imbalance.
* Ingenic:
- Migration to exec_op()
- Fix the RB gpio active-high property on qi, lb60
- Make qi_lb60_ooblayout_ops static.
* Marvell:
- Misc cleanup and small fixes
* Nandsim:
- Fix the error paths, driver wide.
* Omap_elm:
- Fix runtime PM imbalance.
* STM32_FMC2:
- Misc cleanups (error cases, comments, timeout valus, cosmetic
changes).
This introduces mtdpstore, which is similar to mtdoops but more
powerful. It uses pstore/blk, and aims to store panic and oops logs to
a flash partition, where pstore can later read back and present as files
in the mounted pstore filesystem.
To make mtdpstore work, the "blkdev" of pstore/blk should be set
as MTD device name or MTD device number. For more details, see
Documentation/admin-guide/pstore-blk.rst
This solves a number of issues:
- Work duplication: both of pstore and mtdoops do the same job storing
panic/oops log. They have very similar logic, registering to kmsg
dumper and storing logs to several chunks one by one.
- Layer violations: drivers should provides methods instead of polices.
MTD should provide read/write/erase operations, and allow a higher
level drivers to provide the chunk management, kmsg dump
configuration, etc.
- Missing features: pstore provides many additional features, including
presenting the logs as files, logging dump time and count, and
supporting other frontends like pmsg, console, etc.
Signed-off-by: WeiXiong Liao <liaoweixiong@allwinnertech.com>
Link: https://lore.kernel.org/lkml/20200511233229.27745-11-keescook@chromium.org/
Link: https://lore.kernel.org/r/1589266715-4168-1-git-send-email-liaoweixiong@allwinnertech.com
Signed-off-by: Kees Cook <keescook@chromium.org>
NAND ECC modes (or providers) have their own enumeration but, unlike
their algorithms counterpart, there is no invalid or uninitialized
value to discriminate between an error and having chosen a no-ECC
situation. Add an "invalid" entry for this purpose.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200526195633.11543-7-miquel.raynal@bootlin.com
This scheme has been introduced for the Davinci controller and means
that the OOB area must be read *before* the rest of the data. This has
nothing to do with the ECC in OOB placement as it could be understood
and most importantly, there is no point in having this function out of
the Davinci NAND controller driver. A DT property for this scheme has
been added but never used, even by the Davinci driver which only uses
this scheme to change the default nand_read_page().
Move the main read_page() helper into the Davinci driver and remove
the remaining boilerplate.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200526195633.11543-4-miquel.raynal@bootlin.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Now that all drivers have been converted to do not use nand_release()
anymore, let's remove this helper.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-63-miquel.raynal@bootlin.com
nand_release() basically calls mtd_device_unregister() and
nand_cleanup(). Both helpers should be called after MTD device
registration and NAND scan, respectively. Drop nand_release() and use
the two helpers directly so that they fit the error path and the
labels there.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200525085851.17682-12-miquel.raynal@bootlin.com
ns_free() is the helper that is called symmetrically to ns_init() and
so should free the same objects, including the partition names.
Now, callers of ns_free() do not need to free this partition names
themselves.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200525085851.17682-11-miquel.raynal@bootlin.com
Many function calls are done this way:
if ((retval = func()) != 0)
return retval;
while we expect in the kernel function calls like:
retval = func();
if (retval)
return retval;
Apply this change where possible and also use "ret" instead of
"retval" in ns_init_module for consistency, as it is only used in this
function.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200525085851.17682-5-miquel.raynal@bootlin.com
Some functions are prefixed "nandsim_", others "ns_" and many are
simply not prefixed at all. Make this file consistent by prefixing all
functions by "ns_".
This is a mechanical change. Sometimes the line is a bit reworked as
well to fit the kernel coding style. For instance, there are several
places where displayed strings are cut. When one of this line is
changed because of the naming update, the two parts of the strings
gets concatenated.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200525085851.17682-4-miquel.raynal@bootlin.com
Only v3.3-v5.0 have a different CS0 layout.
Controllers before v3.3 use the same layout for every CS.
Fixes: 27c5b17cd1 ("mtd: nand: add NAND driver "library" for Broadcom STB NAND controller")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200522121524.4161539-3-noltari@gmail.com
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200522104008.28340-1-dinghao.liu@zju.edu.cn
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200522095139.19653-1-dinghao.liu@zju.edu.cn
Let's convert the driver to exec_op() to have one less driver relying
on the legacy interface.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Tested-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519232454.374081-4-boris.brezillon@collabora.com
The rb-gpios semantics was undocumented and qi,lb60 (along with the
ingenic driver) got it wrong. The active state encodes the NAND ready
state, which is high level. Since there's no signal inverter on this
board, it should be active-high. Let's fix that here for older DTs so
we can re-use the generic nand_gpio_waitrdy() helper, and be consistent
with what other drivers do.
Suggested-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519232454.374081-3-boris.brezillon@collabora.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Let's stop using nand_release() by calling mtd_device_unregister() and
nand_cleanup() directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-62-miquel.raynal@bootlin.com
nand_release() is supposed be called after MTD device registration.
Here, only nand_scan() happened, so use nand_cleanup() instead.
There is no real Fixes tag applying here as the use of nand_release()
in this driver predates the introduction of nand_cleanup() in
commit d44154f969 ("mtd: nand: Provide nand_cleanup() function to free NAND related resources")
which makes this change possible. However, pointing this commit as the
culprit for backporting purposes makes sense even if this commit is not
introducing any bug.
Fixes: d44154f969 ("mtd: nand: Provide nand_cleanup() function to free NAND related resources")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-61-miquel.raynal@bootlin.com
Han Xu