The snprintf() function returns the number of characters (not
counting the NUL terminator) that it would have printed if we
had space.
This buffer has UBIFS_DFS_DIR_LEN characters plus one extra for
the terminator. Printing UBIFS_DFS_DIR_LEN is okay but anything
higher will result in truncation. Thus the comparison needs to be
change from == to >.
These strings are compile time constants so this patch doesn't
affect runtime.
Fixes: ae380ce047 ("UBIFS: lessen the size of debugging info data structure")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Alexander Dahl <ada@thorsis.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
There is no reason to be limited to 4kiB page NAND chips just because
this is the maximum length the ELM is able to handle in one go. Just
call the ELM several times and it will process as many data as needed.
Here we introduce the concept of ECC page (which is at most 4kiB). The
ELM will be sought as many times as there are ECC pages.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Ryan Barnett <ryan.barnett@collins.com>
Link: https://lore.kernel.org/linux-mtd/20210610134906.3503303-6-miquel.raynal@bootlin.com
The macro BADBLOCK_MARKER_LENGTH is pretty long and could be reduced to
BBM_LEN which is more handy to use in the code.
This is a purely cosmetic change and is only done to avoid further
change to contain 100+ char lines just because of this definition.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210610134906.3503303-3-miquel.raynal@bootlin.com
This hardware controller is embedded in XilinX Zynq-7000 SoCs and has
partial support for Hamming ECC correction.
This work is inspired from the original contributions of Punnaiah
Choudary Kalluri and Naga Sureshkumar Relli.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Michael Walle <michael@walle.cc> [on zynq-7000]
Link: https://lore.kernel.org/linux-mtd/20210610082040.2075611-19-miquel.raynal@bootlin.com
After power up, all SPI NAND's blocks are locked. Only read operations
are allowed, write and erase operations are forbidden.
The SPI NAND framework unlocks all the blocks during its initialization.
During a standby low power, the memory is powered down, losing its
configuration.
During the resume, the QSPI driver state is restored but the SPI NAND
framework does not reconfigured the memory.
This patch adds SPI-NAND MTD PM handlers for resume ops.
SPI NAND resume op re-initializes SPI NAND flash to its probed state.
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210602094913.26472-4-patrice.chotard@foss.st.com
There are 2 timing registers:
- "data interface"
- "timings"
So far, the "data interface" register was named "timings" which begins
misleading when bringing support for the "timings" register. Rename it
to "data_iface".
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210527084959.208804-1-miquel.raynal@bootlin.com
Without the use of le16_to_cpu(), these accesses would have been wrong
on a big-endian machine.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 45606518f9 ("mtd: rawnand: Add onfi_fill_nvddr_interface_config() helper")
Fixes: 9310668fb6 ("mtd: rawnand: Retrieve NV-DDR timing modes from the ONFI parameter page")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210527084913.208635-1-miquel.raynal@bootlin.com
Xilinx ZynqMP SoC and the Arasan controller support 64-bit DMA
addressing. Define the right mask otherwise the default is 32
and some accesses may overflow the default mask.
Reported-by: Jorge Courett <jorge.courett@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Jorge Courett <jorge.courett@gmail.com>
Link: https://lore.kernel.org/linux-mtd/20210527084548.208429-1-miquel.raynal@bootlin.com
Information was redundant between struct pstore_zone_info and struct
pstore_device_info. Use struct pstore_zone_info, with member name "zone".
Additionally untangle the logic for the "best effort" block device
instance.
Signed-off-by: Kees Cook <keescook@chromium.org>
Fixed-by: Pu Lehui <pulehui@huawei.com>
Link: https://lore.kernel.org/lkml/20210617005424.182305-1-pulehui@huawei.com
Various places expect the request_queue in ->rq. Initialize it to
avoid NULL pointer derefences.
Fixes: 6966bb921d ("mtd_blkdevs: use blk_mq_alloc_disk")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add support to show the manufacturer, the partname and JEDEC identifier
as well as to dump the SFDP table. Not all flashes list their SFDP table
contents in their datasheet. So having that is useful. It might also be
helpful in bug reports from users.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Due to possible mode switching to 8D-8D-8D, it might not be possible to
read the SFDP after the initial probe. To be able to dump the SFDP via
sysfs afterwards, make a complete copy of it.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Tested-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Fixes scripts/checkpatch.pl warning:
WARNING: Possible unnecessary 'out of memory' message
Remove it can help us save a bit of memory.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210610022850.15397-1-thunder.leizhen@huawei.com
Fixes scripts/checkpatch.pl warning:
WARNING: Possible unnecessary 'out of memory' message
Remove it can help us save a bit of memory.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210610022631.15344-1-thunder.leizhen@huawei.com
Fixes scripts/checkpatch.pl warning:
WARNING: Possible unnecessary 'out of memory' message
Remove it can help us save a bit of memory.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210610022416.15291-1-thunder.leizhen@huawei.com
Fixes scripts/checkpatch.pl warning:
WARNING: Possible unnecessary 'out of memory' message
Remove it can help us save a bit of memory.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210610022239.15238-1-thunder.leizhen@huawei.com
Fixes scripts/checkpatch.pl warning:
WARNING: Possible unnecessary 'out of memory' message
Remove it can help us save a bit of memory.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210610022100.15185-1-thunder.leizhen@huawei.com
Fixes scripts/checkpatch.pl warning:
WARNING: Possible unnecessary 'out of memory' message
Remove it can help us save a bit of memory.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210610021400.15132-1-thunder.leizhen@huawei.com
Fixes scripts/checkpatch.pl warning:
WARNING: Possible unnecessary 'out of memory' message
Remove it can help us save a bit of memory.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210610021201.15076-1-thunder.leizhen@huawei.com
Fixes scripts/checkpatch.pl warning:
WARNING: Possible unnecessary 'out of memory' message
Remove it can help us save a bit of memory.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210610020958.15023-1-thunder.leizhen@huawei.com
Fixes scripts/checkpatch.pl warning:
WARNING: Possible unnecessary 'out of memory' message
Remove it can help us save a bit of memory.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210610020620.14970-1-thunder.leizhen@huawei.com
Fixes scripts/checkpatch.pl warning:
WARNING: Possible unnecessary 'out of memory' message
Remove it can help us save a bit of memory.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210610020130.14917-1-thunder.leizhen@huawei.com
Fixes scripts/checkpatch.pl warning:
WARNING: Possible unnecessary 'out of memory' message
Remove it can help us save a bit of memory.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210610015052.14864-1-thunder.leizhen@huawei.com
Compared with the definition of DEVICE_ATTR_RO/RW(), the read and write
function names of the sysfs attribute have an additional "mtd_" prefix.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210603125323.12142-2-thunder.leizhen@huawei.com
In the raw NAND world, ECC engines increment ecc_stats and the final
caller is responsible for returning -EBADMSG if the verification
failed.
In the SPI-NAND world it was a bit different until now because there was
only one possible ECC engine: the on-die one. Indeed, the
spinand_mtd_read() call was incrementing the ecc_stats counters
depending on the outcome of spinand_check_ecc_status() directly.
So now let's split the logic like this:
- spinand_check_ecc_status() is specific to the SPI-NAND on-die engine
and is kept very simple: it just returns the ECC status (bonus point:
the content of this helper can be overloaded).
- spinand_ondie_ecc_finish_io_req() is the caller of
spinand_check_ecc_status() and will increment the counters and
eventually return -EBADMSG.
- spinand_mtd_read() is not tied to the on-die ECC implementation and
should be able to handle results coming from other ECC engines: it has
the responsibility of returning the maximum number of bitflips which
happened during the entire operation as this is the only helper that
is aware that several pages may be read in a row.
Fixes: 945845b54c ("mtd: spinand: Instantiate a SPI-NAND on-die ECC engine")
Reported-by: YouChing Lin <ycllin@mxic.com.tw>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: YouChing Lin <ycllin@mxic.com.tw>
Link: https://lore.kernel.org/linux-mtd/20210527084345.208215-1-miquel.raynal@bootlin.com
Use blk_mq_alloc_disk and blk_cleanup_disk to simplify the gendisk and
request_queue allocation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Link: https://lore.kernel.org/r/20210602065345.355274-27-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Use the blk_mq_alloc_disk API to simplify the gendisk and request_queue
allocation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Link: https://lore.kernel.org/r/20210602065345.355274-10-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Winbond flashes with OTP support provide a command to erase the OTP
data. This might come in handy during development.
This was tested with a Winbond W25Q32JW on a LS1028A SoC with the
NXP FSPI controller.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
SPI NOR flashes will just ignore program commands if the OTP region is
locked. Thus, a user might not notice that the intended write didn't end
up in the flash. Return -EROFS to the user in this case. From what I can
tell, chips/cfi_cmdset_0001.c also return this error code.
One could optimize spi_nor_mtd_otp_range_is_locked() to read the status
register only once and not for every OTP region, but for that we would
need some more invasive changes. Given that this is
one-time-programmable memory and the normal access mode is reading, we
just live with the small overhead.
By moving the code around a bit, we can just check the length before
calling spi_nor_mtd_otp_range_is_locked() and avoid an underflow there
if a len is 0. This way we don't need to take the lock either. We also
skip the "*retlen = 0" assignment, mtdcore already takes care of that
for us.
Fixes: 069089acf8 ("mtd: spi-nor: add OTP support")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Use the wording as used in the datasheet to describe the access methods
of the security registers (aka OTP storage). This will also match the
function names.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The security registers either take a 3 byte or a 4 byte address offset,
depending on the address mode of the flash. Thus just leave the
nor->addr_width as is.
Fixes: cad3193fe9 ("mtd: spi-nor: implement OTP support for Winbond and similar flashes")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Make use of spi-mem poll status APIs to let advanced controllers
optimize wait operations.
This should also fix the high CPU usage for system that don't have
a dedicated STATUS poll block logic.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210518162754.15940-3-patrice.chotard@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Macronix MX25L12805D supports locking with 4 block
protection bits in its status register. Add the corresponding
flag in order to clear these bits when unloking the flash.
Otherwise, the flash might not be writable depending on the state
left by the bootloader.
Tested-on: Ubiquiti UniFi AC Lite (ath79)
Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
According to macronix website, there is no mx66l51235l part number.
The chip detected as such is actually mx66l51235f. Rename the flash.
Do not update the mx66l51235l name from the spi_nor_dev_ids[], since
there are dt that are using this compatible.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Intel Alder Lake-M has the same SPI serial flash controller as Alder
Lake-S. Add Alder Lake-M PCI ID to the driver list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Use the correct argument names in the kerneldoc.
Fixes: cad3193fe9 ("mtd: spi-nor: implement OTP support for Winbond and similar flashes")
Reported-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Document what the function does and that it should only be used when it
is known that the device supports it. This will avoid unaware
programmers thinking that they can arbitrarily use it to reset the
device.
Suggested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Use SPI_MODE_X_MASK instead of open coded variant.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
The result of an expression consisting of a single relational operator is
already of the bool type and does not need to be evaluated explicitly.
No functional change.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210510114944.3527-1-thunder.leizhen@huawei.com
Make use of the cs-gpios DT property as well as the core helper to parse
it so that the Arasan controller driver can now assert many more chips
than natively.
The Arasan controller has an internal limitation: RB0 is tied to CS0 and
RB1 is tied to CS1. Hence, it is possible to use external GPIOs as long
as one or the other native CS is not used (or configured to be driven as
a GPIO) and that all additional CS are physically wired on its
corresponding RB line. Eg. CS0 is used as a native CS, CS1 is not used
as native CS and may be used as a GPIO CS, CS2 is an additional GPIO
CS. Then the target asserted by CS0 should also be wired to RB0, while
the targets asserted by CS1 and CS2 should be wired to RB1.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210526093242.183847-5-miquel.raynal@bootlin.com
The controller being always asserting one CS or the other, there is no
need to actually select the right target before doing a page read/write.
However, the anfc_select_target() helper actually also changes the
timing configuration and clock in the case were two different NAND chips
with different timing requirements would be used. In this situation, we
must ensure proper configuration of the controller by calling it.
As a consequence of this change, the anfc_select_target() helper is
being moved earlier in the driver.
Fixes: 88ffef1b65 ("mtd: rawnand: arasan: Support the hardware BCH ECC engine")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210526093242.183847-4-miquel.raynal@bootlin.com
New chips may feature a lot of CS because of their extended length. As
many controllers have been designed a decade ago, they usually only
feature just a couple. This does not mean that the entire range of
these chips cannot be accessed: it is just a matter of adding more
GPIO CS in the hardware design. A DT property has been added to
describe the CS array: cs-gpios.
Here is the code parsing it this new property, allocating what needs to
be, requesting the GPIOs and returning an array with the additional
available CS. The first entries of this array are left empty and are
reserved for native CS.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210526093242.183847-3-miquel.raynal@bootlin.com
Add cleanup function as the name variable for the partition name was
allocaed but never freed after the use as the add mtd function
duplicate the name and free the pparts struct as the partition name is
assumed to be static.
The leak was found using kmemleak.
Fixes: 803eb124e1 ("mtd: parsers: Add Qcom SMEM parser")
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210525230931.30013-1-ansuelsmth@gmail.com
fis-index-block is seeked in the master node and not in the partitions node.
For following binding and current usage, the driver need to check the
partitions subnode.
Fixes: c0e118c8a1 ("mtd: partitions: Add OF support to RedBoot partitions")
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210520114851.1274609-1-clabbe@baylibre.com
As explained in the comment introduced above the fix, the Arasan
controller driver starts an operation when the prog register is being
written with a "type" specific to the action to perform.
The prog type used until now to perform a CHANGE READ COLUMN with an SDR
interface was the PAGE READ type (CMD + ADDR + CMD +
DATA). Unfortunately, for an unknown reason (let's call this a silicon
bug) any CHANGE READ COLUMN performed this way in NV-DDR mode will fail:
the data ready flag will never be triggered, nor will be the transfer
complete flag. Forcefully, this leads to a timeout situation which is
not easy to handle.
Fortunately, it was spotted that sending the same commands through a
different prog register "type", CHANGE READ COLUMN ENHANCED, would work
all the time (even though this particular command is not supported by
the core and is only available in a limited set of devices - we only
care about the controller configuration and not the actual command which
is sent to the device). So let's use this type instead when a CHANGE
READ COLUMN is requested.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-22-miquel.raynal@bootlin.com
Now that the necessary peaces to support the NV-DDR interface type have
been contributed, let's add the relevant logic to make use of it. In
particular, the core does not choose the best SDR timings anymore but
calls a more generic helper instead.
This helper checks if NV-DDR is supported by trying to find the best
NV-DDR supported mode through a logic very close to what is being done
for SDR timings. If no NV-DDR mode in common between the NAND controller
and the NAND chip is found, the core will fallback to SDR.
Side note: theoretically, the data clock speed in NV-DDR mode 0 is
slower than in SDR mode 5. In the situation where we would get a working
NV-DDR mode 0, we could also try if SDR mode 5 is supported and
eventually fallback to it in order to get the fastest possible
throughput. However, in the field, it looks like most of the devices
supporting NV-DDR avoid implementing the fastest SDR modes (like 4 and 5
EDO modes, which are a bit more complicated to handle than the other SDR
modes). So, we will stick to the simplest logic: try NV-DDR otherwise
fallback to SDR. If someone else experiences strong differences because
of that we may still implement the logic defined above.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-19-miquel.raynal@bootlin.com
Until now the parameter of the ADDR_TIMING_MODE feature was just the
ONFI timing mode (from 0 to 5) because we were only supporting the SDR
data interface. In the same byte, bits 4 and 5 indicate which data
interface is being configured so use them to set the right mode and also
read them back to ensure the right timing has been setup on the chip's
side.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-17-miquel.raynal@bootlin.com
Introduce a similar helper to onfi_find_closest_sdr_mode(), but for
NV-DDR timings. It just takes a timing structure as parameter and
returns the closest mode by comparing all minimum timings. This is
useful for rigid controllers on which tuning the timings is not
possible.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-16-miquel.raynal@bootlin.com
As explained in chapter "NV-DDR / NV-DDR2 / NV-DDR3 and Repeat Bytes" of
the ONFI specification, with some commands (mainly the commands which do
not transfer actual data) the data bytes are repeated twice and it is
the responsibility of the receiver to discard them properly. The
concerned commands are: SET_FEATURES, READ_ID, GET_FEATURES,
READ_STATUS, READ_STATUS_ENHANCED, ODT_CONFIGURE. Hence, in the NAND
core we are only impacted by the implementation of READ_ID, GET_FEATURES
and READ_STATUS.
The logic is the same for all:
2/ Check if it is relevant to read all data bytes twice.
1/ Allocate a buffer with twice the requested size (may be done
statically).
2/ Update the instruction structure to read these extra bytes in the
allocated buffer.
3/ Copy the even bytes into the original buffer. The performance hit is
negligible on such small data transfers anyway and we don't really
care about performances at this stage anyway.
4/ Free the allocated buffer, if any.
Note: nand_data_read_op() is also impacted because it is theoretically
possible to run the command/address cycles first, and, as another
operation, do the data transfers. In this case we can easily identify
the impacted commands because the force_8bit flag will be set (due to
the same reason: their data does not go through the same pipeline).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-15-miquel.raynal@bootlin.com
Most timings related to the bus timings are different between SDR and
NV-DDR. However, we identified 9 individual timings which are more
related to the NAND chip internals. These are common between the two
interface types. Fortunately, only these common timings are being shared
through the NAND core and its ->exec_op() interface, which allows the
writing of a simple macro checking the interface type and depending on
it, returning either the relevant SDR timing or the NV-DDR timing. This
is the purpose of the NAND_COMMON_TIMING_PS() macro.
As all this is evaluated at build time, one will immediately be notified
in case a non common timing is being accessed through this macro.
Two handy macros are also inserted at the same time, which use
PSEC_TO_NSEC or PSEC_TO_MSEC so that it is very easy to return timings
in milli-, nano- or pico-seconds, as usually requested by the internal
API.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-14-miquel.raynal@bootlin.com
Legacy code should not benefit from newer features, especially in
helpers that have been deprecated for a very long time. People who want
NV-DDR support must migrate their driver to the ->exec_op() API.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-13-miquel.raynal@bootlin.com
Same logic as for the SDR path, let's create a
onfi_fill_nvddr_interface_config() helper to fill an interface
configuration structure with NV-DDR timings, given a specific ONFI mode.
There is one additional thing to do compared to SDR mode: tCAD timing
can be fast or slow and this depends on an ONFI parameter page bit. By
default the slow value is declared in the timings structure definition,
but this helper can shrink it down if necessary.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-12-miquel.raynal@bootlin.com
This helper actually fills the interface configuration with SDR data.
As part of the work to bring NV-DDR support, let's rename this helper
onfi_fill_sdr_interface_config() and add a generic indirection to it.
There are no functional changes here, but this will simplify a next
change which adds onfi_fill_nvddr_interface_config() support.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-11-miquel.raynal@bootlin.com
When parsing the ONFI parameter page, save the available NV-DDR timing
modes in the core's dynamic ONFI structure. Once available to the rest
of the core out of the ONFI driver, these values will then be used to
derive the best timing mode.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-10-miquel.raynal@bootlin.com
In particular, first ONFI specifications referred to SDR modes as
asynchronous modes, which is not the term we usually have in mind. The
spec has then been updated, so do the same here in the NAND subsystem to
avoid any possible confusion.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-7-miquel.raynal@bootlin.com
If kmalloc() fails then it could lead to a NULL dereference. Check and
return -ENOMEM on error.
Fixes: 4b361cfa86 ("mtd: core: add OTP nvmem provider support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/YJ6Iw3iNvGycAWV6@mwanda
Commit 4b361cfa86 ("mtd: core: add OTP nvmem provider support") is
causing the following panic ...
------------[ cut here ]------------
kernel BUG at /local/workdir/tegra/linux_next/kernel/mm/slab.c:2730!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 3 PID: 1 Comm: swapper/0 Not tainted 5.13.0-rc2-next-20210518 #1
Hardware name: NVIDIA Tegra SoC (Flattened Device Tree)
PC is at ___cache_free+0x3f8/0x51c
...
[<c029bb1c>] (___cache_free) from [<c029c658>] (kfree+0xac/0x1bc)
[<c029c658>] (kfree) from [<c06da094>] (mtd_otp_size+0xc4/0x108)
[<c06da094>] (mtd_otp_size) from [<c06dc864>] (mtd_device_parse_register+0xe4/0x2b4)
[<c06dc864>] (mtd_device_parse_register) from [<c06e3ccc>] (spi_nor_probe+0x210/0x2c0)
[<c06e3ccc>] (spi_nor_probe) from [<c06e9578>] (spi_probe+0x88/0xac)
[<c06e9578>] (spi_probe) from [<c066891c>] (really_probe+0x214/0x3a4)
[<c066891c>] (really_probe) from [<c0668b14>] (driver_probe_device+0x68/0xc0)
[<c0668b14>] (driver_probe_device) from [<c0666cf8>] (bus_for_each_drv+0x5c/0xbc)
[<c0666cf8>] (bus_for_each_drv) from [<c0668694>] (__device_attach+0xe4/0x150)
[<c0668694>] (__device_attach) from [<c06679e0>] (bus_probe_device+0x84/0x8c)
[<c06679e0>] (bus_probe_device) from [<c06657f8>] (device_add+0x48c/0x868)
[<c06657f8>] (device_add) from [<c06eb784>] (spi_add_device+0xa0/0x168)
[<c06eb784>] (spi_add_device) from [<c06ec9a8>] (spi_register_controller+0x8b8/0xb38)
[<c06ec9a8>] (spi_register_controller) from [<c06ecc3c>] (devm_spi_register_controller+0x14/0x50)
[<c06ecc3c>] (devm_spi_register_controller) from [<c06f0510>] (tegra_spi_probe+0x33c/0x450)
[<c06f0510>] (tegra_spi_probe) from [<c066abec>] (platform_probe+0x5c/0xb8)
[<c066abec>] (platform_probe) from [<c066891c>] (really_probe+0x214/0x3a4)
[<c066891c>] (really_probe) from [<c0668b14>] (driver_probe_device+0x68/0xc0)
[<c0668b14>] (driver_probe_device) from [<c0668e30>] (device_driver_attach+0x58/0x60)
[<c0668e30>] (device_driver_attach) from [<c0668eb8>] (__driver_attach+0x80/0xc8)
[<c0668eb8>] (__driver_attach) from [<c0666c48>] (bus_for_each_dev+0x78/0xb8)
[<c0666c48>] (bus_for_each_dev) from [<c0667c44>] (bus_add_driver+0x164/0x1e8)
[<c0667c44>] (bus_add_driver) from [<c066997c>] (driver_register+0x7c/0x114)
[<c066997c>] (driver_register) from [<c010223c>] (do_one_initcall+0x50/0x2b0)
[<c010223c>] (do_one_initcall) from [<c11011f0>] (kernel_init_freeable+0x1a8/0x1fc)
[<c11011f0>] (kernel_init_freeable) from [<c0c09190>] (kernel_init+0x8/0x118)
[<c0c09190>] (kernel_init) from [<c01001b0>] (ret_from_fork+0x14/0x24)
...
---[ end trace 0f652dd222de75d7 ]---
In the function mtd_otp_size() a buffer is allocated by calling
kmalloc() and a pointer to the buffer is stored in a variable 'info'.
The pointer 'info' may then be incremented depending on the length
returned from mtd_get_user/fact_prot_info(). If 'info' is incremented,
when kfree() is called to free the buffer the above panic occurs because
we are no longer passing the original address of the buffer allocated.
Fix this by indexing through the buffer allocated to avoid incrementing
the pointer.
Fixes: 4b361cfa86 ("mtd: core: add OTP nvmem provider support")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210518185503.162787-1-jonathanh@nvidia.com
Since the Hamming software ECC engine has been updated to become a
proper and independent ECC engine, it is now mandatory to either
initialize the engine before using any one of his functions or use one
of the bare helpers which only perform the calculations. As there is no
actual need for a proper ECC initialization, let's just use the bare
helper instead of the rawnand one.
Fixes: 90ccf0a019 ("mtd: nand: ecc-hamming: Rename the exported functions")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210413161840.345208-8-miquel.raynal@bootlin.com
Since the Hamming software ECC engine has been updated to become a
proper and independent ECC engine, it is now mandatory to either
initialize the engine before using any one of his functions or use one
of the bare helpers which only perform the calculations. As there is no
actual need for a proper ECC initialization, let's just use the bare
helper instead of the rawnand one.
Fixes: 90ccf0a019 ("mtd: nand: ecc-hamming: Rename the exported functions")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210413161840.345208-7-miquel.raynal@bootlin.com
Since the Hamming software ECC engine has been updated to become a
proper and independent ECC engine, it is now mandatory to either
initialize the engine before using any one of his functions or use one
of the bare helpers which only perform the calculations. As there is no
actual need for a proper ECC initialization, let's just use the bare
helper instead of the rawnand one.
Fixes: 90ccf0a019 ("mtd: nand: ecc-hamming: Rename the exported functions")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210413161840.345208-6-miquel.raynal@bootlin.com
Since the Hamming software ECC engine has been updated to become a
proper and independent ECC engine, it is now mandatory to either
initialize the engine before using any one of his functions or use one
of the bare helpers which only perform the calculations. As there is no
actual need for a proper ECC initialization, let's just use the bare
helper instead of the rawnand one.
Fixes: 90ccf0a019 ("mtd: nand: ecc-hamming: Rename the exported functions")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210413161840.345208-5-miquel.raynal@bootlin.com
Since the Hamming software ECC engine has been updated to become a
proper and independent ECC engine, it is now mandatory to either
initialize the engine before using any one of his functions or use one
of the bare helpers which only perform the calculations. As there is no
actual need for a proper ECC initialization, let's just use the bare
helper instead of the rawnand one.
Fixes: 90ccf0a019 ("mtd: nand: ecc-hamming: Rename the exported functions")
Cc: stable@vger.kernel.org
Cc: Vladimir Zapolskiy <vz@mleia.com>
Reported-by: Trevor Woerner <twoerner@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Trevor Woerner <twoerner@gmail.com>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Link: https://lore.kernel.org/linux-mtd/20210413161840.345208-4-miquel.raynal@bootlin.com
Since the Hamming software ECC engine has been updated to become a
proper and independent ECC engine, it is now mandatory to either
initialize the engine before using any one of his functions or use one
of the bare helpers which only perform the calculations. As there is no
actual need for a proper ECC initialization, let's just use the bare
helper instead of the rawnand one.
Fixes: 90ccf0a019 ("mtd: nand: ecc-hamming: Rename the exported functions")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210413161840.345208-3-miquel.raynal@bootlin.com
Since the Hamming software ECC engine has been updated to become a
proper and independent ECC engine, it is now mandatory to either
initialize the engine before using any one of his functions or use one
of the bare helpers which only perform the calculations. As there is no
actual need for a proper ECC initialization, let's just use the bare
helper instead of the rawnand one.
Fixes: 90ccf0a019 ("mtd: nand: ecc-hamming: Rename the exported functions")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210413161840.345208-2-miquel.raynal@bootlin.com
In the unlikely event that both blocks 10 and 11 are marked as bad (on a
32 bit machine), then the process of marking block 10 as bad stomps on
cached entry for block 11. There are (of course) other examples.
Signed-off-by: Patrick Doyle <pdoyle@irobot.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Yoshio Furuyama <ytc-mb-yfuruyama7@kioxia.com>
[<miquel.raynal@bootlin.com>: Fixed the title]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/774a92693f311e7de01e5935e720a179fb1b2468.1616635406.git.ytc-mb-yfuruyama7@kioxia.com
A star has been added to subsequent line of block comment
The closing */ has been shifted to new line
This is done to maintain code uniformity
Signed-off-by: Shubhankar Kuranagatti <shubhankarvk@gmail.com>
[<miquel.raynal@bootlin.com>: Fixed the title]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210504062059.mywqzwveyjfawreg@kewl-virtual-machine
Partname and partid are set by the upper driver (spi-nor) on the master
MTD. If this MTD is partitioned and CONFIG_MTD_PARTITIONED_MASTER is
disabled, the master MTD is not instantiated and partname and partid
aren't available to the userspace.
Always read the partname and partid from the master MTD, they describe
the HW, which can't differ between master and its children.
Signed-off-by: Petr Malat <oss@malat.biz>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210430065057.32018-1-oss@malat.biz
Variable 'err' is set to 0 but this value is never read as it is
overwritten with a new value later on, hence it is a redundant
assignment and can be removed.
Cleans up the following clang-analyzer warning:
drivers/mtd/tests/torturetest.c:233:2: warning: Value stored to 'err' is
never read [clang-analyzer-deadcode.DeadStores]
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1619604142-119891-1-git-send-email-yang.lee@linux.alibaba.com
The driver is using -1 instead of the -ENOMEM defined macro to
specify that a buffer allocation failed. Using the correct error
code is more intuitive
Smatch tool warning:
drivers/mtd/inftlmount.c:333 check_free_sectors() warn: returning -1
instead of -ENOMEM is sloppy
drivers/mtd/nftlmount.c:272 check_free_sectors() warn: returning -1
instead of -ENOMEM is sloppy
No functional change, just more standardized.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
[<miquel.raynal@bootlin.com>: Fixed the title]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1619429543-52234-1-git-send-email-yang.lee@linux.alibaba.com
Variable err is set to zero but this value is never read as it is
overwritten with a new value later on, hence it is a redundant
assignment and can be removed.
Cleans up the following clang-analyzer warning:
drivers/mtd/tests/oobtest.c:626:4: warning: Value stored to 'err' is
never read [clang-analyzer-deadcode.DeadStores].
drivers/mtd/tests/oobtest.c:603:4: warning: Value stored to 'err' is
never read [clang-analyzer-deadcode.DeadStores].
drivers/mtd/tests/oobtest.c:579:4: warning: Value stored to 'err' is
never read [clang-analyzer-deadcode.DeadStores].
drivers/mtd/tests/oobtest.c:556:4: warning: Value stored to 'err' is
never read [clang-analyzer-deadcode.DeadStores].
drivers/mtd/tests/oobtest.c:532:3: warning: Value stored to 'err' is
never read [clang-analyzer-deadcode.DeadStores].
drivers/mtd/tests/oobtest.c:509:3: warning: Value stored to 'err' is
never read [clang-analyzer-deadcode.DeadStores].
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1619346498-43617-1-git-send-email-jiapeng.chong@linux.alibaba.com
Flash OTP regions can already be read via user space. Some boards have
their serial number or MAC addresses stored in the OTP regions. Add
support for them being a (read-only) nvmem provider.
The API to read the OTP data is already in place. It distinguishes
between factory and user OTP, thus there are up to two different
providers.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210424110608.15748-6-michael@walle.cc
Buffalo uses a different TRX magic for every device, to be able to use
this trx parser, make it possible to specify the TRX magic in device
tree. If no TRX magic is specified in device tree, the standard value
will be used. This value should only be specified if a vendor chooses to
use a non standard TRX magic.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210418214616.239574-3-hauke@hauke-m.de
Commit 82bfd11f1b ("mtd: rawnand: qcom: Add support for Qcom SMEM
parser") made qcomsmem the only parser for qcom_nandc partitions. This
might be problematic for systems with both SPI and NAND MTD devices.
When booting from SPI flash the partition table should not apply to the
NAND flash.
Prepend cmdlinepart and ofpart parsers to allow override of the
partition parser.
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/cf470f05af514acd5bd94548804ffa96b966a0a8.1619029869.git.baruch@tkos.co.il
Dan Carpenter