The "mct_tick" is a per-cpu clockevents device. Set the
CLOCK_EVT_FEAT_PERCPU feature to prevent e.g. mct_tick0 being unsafely
designated as the global broadcast timer and instead treat the device as
a per-cpu wakeup timer.
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Will Deacon <will@kernel.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210608154341.10794-3-will@kernel.org
All arm64 CPUs feature an architected timer, which offers a relatively
low-latency interface to a per-cpu clocksource and timer. For the most
part, using this interface is a no-brainer, with the exception of SoCs
where it cannot be used to wake up from deep idle state (i.e.
CLOCK_EVT_FEAT_C3STOP is set).
On the contrary, the Exynos MCT is extremely slow to access yet can be
used as a wakeup source. In preparation for using the Exynos MCT as a
potential wakeup timer for the Arm architected timer, reduce its ratings
so that the architected timer is preferred.
This effectively reverts the decision made in 6282edb72b
("clocksource/drivers/exynos_mct: Increase priority over ARM arch timer")
for arm64, as the reasoning for the original change was to work around
a 32-bit SoC design.
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Will Deacon <will@kernel.org>
Tested-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> # exynos-5422
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210608154341.10794-2-will@kernel.org
request_irq() is preferred over setup_irq(). The early boot setup_irq()
invocations happen either via 'init_IRQ()' or 'time_init()', while
memory allocators are ready by 'mm_init()'.
Per tglx[1], setup_irq() existed in olden days when allocators were not
ready by the time early interrupts were initialized.
Hence replace setup_irq() by request_irq().
Seldom remove_irq() usage has been observed coupled with setup_irq(),
wherever that has been found, it too has been replaced by free_irq().
A build error that was reported by kbuild test robot <lkp@intel.com>
in the previous version of the patch also has been fixed.
[1] https://lkml.kernel.org/r/alpine.DEB.2.20.1710191609480.1971@nanos
Signed-off-by: afzal mohammed <afzal.mohd.ma@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/91961c77c1cf93d41523f5e1ac52043f32f97077.1582799709.git.afzal.mohd.ma@gmail.com
Fix up inconsistent usage of upper and lowercase letters in "Exynos"
name.
"EXYNOS" is not an abbreviation but a regular trademarked name.
Therefore it should be written with lowercase letters starting with
capital letter.
The lowercase "Exynos" name is promoted by its manufacturer Samsung
Electronics Co., Ltd., in advertisement materials and on website.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200104152107.11407-12-krzk@kernel.org
Exynos SoCs based on CA7/CA15 have 2 timer interfaces: custom Exynos MCT
(Multi Core Timer) and standard ARM Architected Timers.
There are use cases, where both timer interfaces are used simultanously.
One of such examples is using Exynos MCT for the main system timer and
ARM Architected Timers for the KVM and virtualized guests (KVM requires
arch timers).
Exynos Multi-Core Timer driver (exynos_mct) must be however started
before ARM Architected Timers (arch_timer), because they both share some
common hardware blocks (global system counter) and turning on MCT is
needed to get ARM Architected Timer working properly.
To ensure selecting Exynos MCT as the main system timer, increase MCT
timer rating. To ensure proper starting order of both timers during
suspend/resume cycle, increase MCT hotplug priority over ARM Archictected
Timers.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver does not use sched.h and platform_device.h.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
While freeing interrupt handlers in error path, don't assume that all
requested interrupts are per-processor interrupts and properly release
standard interrupts too.
Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
Fixes: 56a94f1391 ("clocksource: exynos_mct: Avoid blocking calls in the cpu hotplug notifier")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Exynos Multi-Core Timer driver is used only on device-tree based
systems, so remove non-dt related code. In case of !CONFIG_OF
the code is anyway equal because of_irq_count() has a stub
returning 0. Device node pointer is always provided when driver
has been probed from device tree.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
When shutting down the timer, ensure that after we have stopped the
timer any pending interrupts are cleared. This fixes a problem when
suspending, as interrupts are disabled before the timer is stopped,
so the timer interrupt may still be asserted, preventing the system
entering a low power state when the wfi is executed.
Signed-off-by: Stuart Menefy <stuart.menefy@mathembedded.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: <stable@vger.kernel.org> # v4.3+
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
When a timer tick occurs and the clock is in one-shot mode, the timer
needs to be stopped to prevent it triggering subsequent interrupts.
Currently this code is in exynos4_mct_tick_clear(), but as it is
only needed when an ISR occurs move it into exynos4_mct_tick_isr(),
leaving exynos4_mct_tick_clear() just doing what its name suggests it
should.
Signed-off-by: Stuart Menefy <stuart.menefy@mathembedded.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: stable@vger.kernel.org # v4.3+
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The CLOCKSOURCE_OF_DECLARE macro is used widely for the timers to declare the
clocksource at early stage. However, this macro is also used to initialize
the clockevent if any, or the clockevent only.
It was originally suggested to declare another macro to initialize a
clockevent, so in order to separate the two entities even they belong to the
same IP. This was not accepted because of the impact on the DT where splitting
a clocksource/clockevent definition does not make sense as it is a Linux
concept not a hardware description.
On the other side, the clocksource has not interrupt declared while the
clockevent has, so it is easy from the driver to know if the description is
for a clockevent or a clocksource, IOW it could be implemented at the driver
level.
So instead of dealing with a named clocksource macro, let's use a more generic
one: TIMER_OF_DECLARE.
The patch has not functional changes.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
When a CPU goes offline a potentially pending timer interrupt is not
cleared. When the CPU comes online again then the pending interrupt is
delivered before the per cpu clockevent device is initialized. As a
consequence the tick interrupt handler dereferences a NULL pointer.
[ 51.251378] Unable to handle kernel NULL pointer dereference at virtual address 00000040
[ 51.289348] task: ee942d00 task.stack: ee960000
[ 51.293861] PC is at tick_periodic+0x38/0xb0
[ 51.298102] LR is at tick_handle_periodic+0x1c/0x90
Clear the pending interrupt in the cpu dying path.
Fixes: 56a94f1391 ("clocksource: exynos_mct: Avoid blocking calls in the cpu hotplug notifier")
Reported-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: linux-samsung-soc@vger.kernel.org
Cc: cw00.choi@samsung.com
Cc: daniel.lezcano@linaro.org
Cc: stable@vger.kernel.org
Cc: javier@osg.samsung.com
Cc: kgene@kernel.org
Cc: krzk@kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/1484628876-22065-1-git-send-email-jy0922.shim@samsung.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull timer type cleanups from Thomas Gleixner:
"This series does a tree wide cleanup of types related to
timers/timekeeping.
- Get rid of cycles_t and use a plain u64. The type is not really
helpful and caused more confusion than clarity
- Get rid of the ktime union. The union has become useless as we use
the scalar nanoseconds storage unconditionally now. The 32bit
timespec alike storage got removed due to the Y2038 limitations
some time ago.
That leaves the odd union access around for no reason. Clean it up.
Both changes have been done with coccinelle and a small amount of
manual mopping up"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
ktime: Get rid of ktime_equal()
ktime: Cleanup ktime_set() usage
ktime: Get rid of the union
clocksource: Use a plain u64 instead of cycle_t
There is no point in having an extra type for extra confusion. u64 is
unambiguous.
Conversion was done with the following coccinelle script:
@rem@
@@
-typedef u64 cycle_t;
@fix@
typedef cycle_t;
@@
-cycle_t
+u64
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: John Stultz <john.stultz@linaro.org>
When the state names got added a script was used to add the extra argument
to the calls. The script basically converted the state constant to a
string, but the cleanup to convert these strings into meaningful ones did
not happen.
Replace all the useless strings with 'subsys/xxx/yyy:state' strings which
are used in all the other places already.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Link: http://lkml.kernel.org/r/20161221192112.085444152@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch allows building and compile-testing the driver also for
ARM64. The delay_timer is only supported on ARMv7.
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
[k.kozlowski: Adjusted commit msg]
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Install the callbacks via the state machine and let the core invoke
the callbacks on the already online CPUs.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-samsung-soc@vger.kernel.org
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160713153338.147940411@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
All the clocksource drivers's init function are now converted to return
an error code. CLOCKSOURCE_OF_DECLARE is no longer used as well as the
clksrc-of table.
Let's convert back the names:
- CLOCKSOURCE_OF_DECLARE_RET => CLOCKSOURCE_OF_DECLARE
- clksrc-of-ret => clksrc-of
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
For exynos_mct and samsung_pwm_timer:
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
For arch/arc:
Acked-by: Vineet Gupta <vgupta@synopsys.com>
For mediatek driver:
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
For the Rockchip-part
Acked-by: Heiko Stuebner <heiko@sntech.de>
For STi :
Acked-by: Patrice Chotard <patrice.chotard@st.com>
For the mps2-timer.c and versatile.c changes:
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
For the OXNAS part :
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
For LPC32xx driver:
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
For Broadcom Kona timer change:
Acked-by: Ray Jui <ray.jui@broadcom.com>
For Sun4i and Sun5i:
Acked-by: Chen-Yu Tsai <wens@csie.org>
For Meson6:
Acked-by: Carlo Caione <carlo@caione.org>
For Keystone:
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
For NPS:
Acked-by: Noam Camus <noamca@mellanox.com>
For bcm2835:
Acked-by: Eric Anholt <eric@anholt.net>
The init functions do not return any error. They behave as the following:
- panic, thus leading to a kernel crash while another timer may work and
make the system boot up correctly
or
- print an error and let the caller unaware if the state of the system
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
set_state_oneshot_stopped() is called by the clkevt core, when the next
event is required at an expiry time of 'KTIME_MAX'. This normally
happens with NO_HZ_{IDLE|FULL} in both LOWRES/HIGHRES modes.
This patch makes the clockevent device to stop on such an event, to
avoid spurious interrupts, as explained by: commit 8fff52fd50
("clockevents: Introduce CLOCK_EVT_STATE_ONESHOT_STOPPED state").
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Since evt structure is embedded in per-CPU mevt structure it's
definitely faster to use container_of() to get access to mevt
if we have evt (for example as incoming function argument) instead
of more expensive approach with this_cpu_ptr(&percpu_mct_tick).
this_cpu_ptr() on per-CPU mevt structure leads to access to cp15
to get cpu id and arithmetic operations.
Container_of() is cheaper since it's just one asm instruction.
This should work if used evt pointer is correct and owned by
local mevt structure.
For example, before this patch set_state_shutdown() looks like:
4a4: e92d4010 push {r4, lr}
4a8: e3004000 movw r4, #0
4ac: ebfffffe bl 0 <debug_smp_processor_id>
4b0: e3003000 movw r3, #0
4b4: e3404000 movt r4, #0
4b8: e3403000 movt r3, #0
4bc: e7933100 ldr r3, [r3, r0, lsl #2]
4c0: e0844003 add r4, r4, r3
4c4: e59400c0 ldr r0, [r4, #192] ; 0xc0
4c8: ebffffd4 bl 420 <exynos4_mct_tick_stop.isra.1>
4cc: e3a00000 mov r0, #0
4d0: e8bd8010 pop {r4, pc}
With this patch:
4a4: e92d4010 push {r4, lr}
4a8: e59000c0 ldr r0, [r0, #192] ; 0xc0
4ac: ebffffdb bl 420 <exynos4_mct_tick_stop.isra.1>
4b0: e3a00000 mov r0, #0
4b4: e8bd8010 pop {r4, pc}
Also, for me size of exynos_mct.o decreased from 84588 bytes
to 83956.
Signed-off-by: Alexey Klimov <alexey.klimov@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Migrate exynos_mct driver to the new 'set-state' interface provided by
clockevents core, the earlier 'set-mode' interface is marked obsolete
now.
This also enables us to implement callbacks for new states of clockevent
devices, for example: ONESHOT_STOPPED.
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Patch removes unneeded container_of() macro in exynos4_local_timer_setup().
Instead let's pass mevt pointer to setup and stop functions from
exynos4_mct_cpu_notify() and let them get evt pointer.
Tested on odroid-xu3.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Whilst testing cpu hotplug events on kernel configured with
DEBUG_PREEMPT and DEBUG_ATOMIC_SLEEP we get following BUG message,
caused by calling request_irq() and free_irq() in the context of
hotplug notification (which is in this case atomic context).
[ 40.785859] CPU1: Software reset
[ 40.786660] BUG: sleeping function called from invalid context at mm/slub.c:1241
[ 40.786668] in_atomic(): 1, irqs_disabled(): 128, pid: 0, name: swapper/1
[ 40.786678] Preemption disabled at:[< (null)>] (null)
[ 40.786681]
[ 40.786692] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 3.19.0-rc4-00024-g7dca860 #36
[ 40.786698] Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[ 40.786728] [<c0014a00>] (unwind_backtrace) from [<c0011980>] (show_stack+0x10/0x14)
[ 40.786747] [<c0011980>] (show_stack) from [<c0449ba0>] (dump_stack+0x70/0xbc)
[ 40.786767] [<c0449ba0>] (dump_stack) from [<c00c6124>] (kmem_cache_alloc+0xd8/0x170)
[ 40.786785] [<c00c6124>] (kmem_cache_alloc) from [<c005d6f8>] (request_threaded_irq+0x64/0x128)
[ 40.786804] [<c005d6f8>] (request_threaded_irq) from [<c0350b8c>] (exynos4_local_timer_setup+0xc0/0x13c)
[ 40.786820] [<c0350b8c>] (exynos4_local_timer_setup) from [<c0350ca8>] (exynos4_mct_cpu_notify+0x30/0xa8)
[ 40.786838] [<c0350ca8>] (exynos4_mct_cpu_notify) from [<c003b330>] (notifier_call_chain+0x44/0x84)
[ 40.786857] [<c003b330>] (notifier_call_chain) from [<c0022fd4>] (__cpu_notify+0x28/0x44)
[ 40.786873] [<c0022fd4>] (__cpu_notify) from [<c0013714>] (secondary_start_kernel+0xec/0x150)
[ 40.786886] [<c0013714>] (secondary_start_kernel) from [<40008764>] (0x40008764)
Interrupts cannot be requested/freed in the CPU_STARTING/CPU_DYING
notifications which run on the hotplugged cpu with interrupts and
preemption disabled.
To avoid the issue, request the interrupts for all possible cpus in
the boot code. The interrupts are marked NO_AUTOENABLE to avoid a racy
request_irq/disable_irq() sequence. The flag prevents the
request_irq() code from enabling the interrupt immediately.
The interrupt is then enabled in the CPU_STARTING notifier of the
hotplugged cpu and again disabled with disable_irq_nosync() in the
CPU_DYING notifier.
[ tglx: Massaged changelog to match the patch ]
Fixes: 7114cd749a ("clocksource: exynos_mct: use (request/free)_irq calls for local timer registration")
Reported-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Marcin Jabrzyk <m.jabrzyk@samsung.com>
Signed-off-by: Damian Eppel <d.eppel@samsung.com>
Cc: m.szyprowski@samsung.com
Cc: kyungmin.park@samsung.com
Cc: daniel.lezcano@linaro.org
Cc: kgene@kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/1435324984-7328-1-git-send-email-d.eppel@samsung.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: <stable@vger.kernel.org>
Since commit 228e3023eb ("Merge tag 'mct-exynos-for-v3.10' of ...") the
mct_init() was superseded by mct_init_dt() and is not referenced
anywhere. Remove it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The struct clocksource 'mct_frc' is not exported and used outside so
make it static.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Return value of exynos4_mct_tick_clear() was never checked so it can
be safely changed to void.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
EXYNOS4_MCT_L_MASK is defined as 0xffffff00, so applying this bitmask
produces a number outside the range 0x00 to 0xff, which always results
in execution of the default switch statement.
Obviously this is wrong and git history shows that the bitmask inversion
was incorrectly set during a refactoring of the MCT code.
Fix this by putting the inversion at the correct position again.
Cc: stable@vger.kernel.org
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Reported-by: GP Orcullo <kinsamanka@gmail.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The MCT has a nice 64-bit counter. That means that we _can_ register
as a 64-bit clocksource and sched_clock. ...but that doesn't mean we
should.
The 64-bit counter is read by reading two 32-bit registers. That
means reading needs to be something like:
- Read upper half
- Read lower half
- Read upper half and confirm that it hasn't changed.
That wouldn't be terrible, but:
- THe MCT isn't very fast to access (hundreds of nanoseconds).
- The clocksource is queried _all the time_.
In total system profiles of real workloads on ChromeOS, we've seen
exynos_frc_read() taking 2% or more of CPU time even after optimizing
the 3 reads above to 2 (see below).
The MCT is clocked at ~24MHz on all known systems. That means that
the 32-bit half of the counter rolls over every ~178 seconds. This
inspired an optimization in ChromeOS to cache the upper half between
calls, moving 3 reads to 2. ...but we can do better! Having a 32-bit
timer that flips every 178 seconds is more than sufficient for Linux.
Let's just use the lower half of the MCT.
Times on 5420 to do 1000000 gettimeofday() calls from userspace:
* Original code: 1323852 us
* ChromeOS cache upper half: 1173084 us
* ChromeOS + ldmia to optimize: 1045674 us
* Use lower 32-bit only (this code): 1014429 us
As you can see, the time used doesn't increase linearly with the
number of reads and we can make 64-bit work almost as fast as 32-bit
with a bit of assembly code. But since there's no real gain for
64-bit, let's go with the simplest and fastest implementation.
Note: with this change roughly half the time for gettimeofday() is
spent in exynos_frc_read(). The rest is timer / system call overhead.
Also note: this patch disables the use of the MCT on ARM64 systems
until we've sorted out how to make "cycles_t" always 32-bit. Really
ARM64 systems should be using arch timers anyway.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Using the __raw functions is discouraged. Update the file to
consistently use the proper functions.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
This patch registers the exynos mct clocksource as the current timer
as it has constant clock rate. This will generate correct udelay for
the exynos platform and avoid using unnecessary calibrated
jiffies. This change has been tested on exynos5420 based board and
udelay is very close to expected.
Without this patch udelay() on exynos5400 / exynos5800 is wildly
inaccurate due to big.LITTLE not adjusting loops_per_jiffy correctly.
Also without this patch udelay() on exynos5250 can be innacruate
during transitions between frequencies < 800 MHz (you'll go 200 MHz ->
800 MHz -> 300 MHz and will run at 800 MHz for a time with the wrong
loops_per_jiffy).
[dianders: reworked and created version 3]
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
In (93bfb76 clocksource: exynos_mct: register sched_clock callback) we
supported using the MCT as a scheduler clock. We properly marked
exynos4_read_sched_clock() as notrace. However, we then went and
called another function that _wasn't_ notrace. That means if you do:
cd /sys/kernel/debug/tracing/
echo function_graph > current_tracer
You'll get a crash.
Fix this (but still let other readers of the MCT be trace-enabled) by
adding an extra function. It's important to keep other users of MCT
traceable because the MCT is actually quite slow to access and we want
exynos4_frc_read() to show up in ftrace profiles if it's the
bottleneck.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Unfortunately on some exynos systems, resetting the mct counter also
resets the architected timer counter. This can cause problems if the
architected timer driver has already been initialized because the kernel
will think that the counter has wrapped around, causing a big jump in
printk timestamps and delaying any scheduled clock events until the
counter reaches the value it had before it was reset.
The kernel code makes no assumptions about the initial value of the mct
counter so there is no reason from a software perspective to clear the
counter before starting it. This also fixes the problems described in
the previous paragraph.
Cc: Olof Johansson <olof@lixom.net>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Chirantan Ekbote <chirantan@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
- register sched_clock callback to use clocksource mct-frc
Note that got ack from Daniel
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=w1kR
-----END PGP SIGNATURE-----
Merge tag 'samsung-drivers' of http://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/drivers
Merge "Samsung driver update for 3.16" from Kukjin Kim:
exynos_mct update for v3.16
- register sched_clock callback to use clocksource mct-frc
* tag 'samsung-drivers' of http://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
clocksource: exynos_mct: register sched_clock callback
Signed-off-by: Olof Johansson <olof@lixom.net>
Use the clocksource mct-frc for sched_clock
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
After hotplugging CPU1 the first call of interrupt handler for CPU1
oneshot timer was called on CPU0 because it fired before setting IRQ
affinity. Affected are SoCs where Multi Core Timer interrupts are
shared (SPI), e.g. Exynos 4210.
During setup of the MCT timers the clock event device should be
registered after setting the affinity for interrupt. This will prevent
starting the timer too early.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Tomasz Figa <t.figa@samsung.com>,
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>,
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: linux-arm-kernel@lists.infradead.org,
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20140416143316.299247848@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The starting cpu is not yet in the online mask so irq_set_affinity()
fails which results in per cpu timers for this cpu ending up on some
other online cpu, ususally cpu 0.
Use irq_force_affinity() which disables the online mask check and
makes things work.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Tomasz Figa <t.figa@samsung.com>,
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>,
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: linux-arm-kernel@lists.infradead.org,
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20140416143316.106665251@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
These cleanup patches are mainly move stuff around and should all
be harmless. They are mainly split out so that other branches can
be based on top to avoid conflicts.
Notable changes are:
* We finally remove all mach/timex.h, after CLOCK_TICK_RATE is no
longer used. (Uwe Kleine-König)
* The Qualcomm MSM platform is split out into legacy mach-msm and
new-style mach-qcom, to allow easier maintainance of the new
hardware support without regressions. (Kumar Gala)
* A rework of some of the Kconfig logic to simplify multiplatform
support (Rob Herring)
* Samsung Exynos gets closer to supporting multiplatform (Sachin
Kamat and others)
* mach-bcm3528 gets merged into mach-bcm (Stephen Warren)
* at91 gains some common clock framework support (Alexandre Belloni,
Jean-Jacques Hiblot and other French people).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=GcBb
-----END PGP SIGNATURE-----
Merge tag 'cleanup-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Arnd Bergmann:
"These cleanup patches are mainly move stuff around and should all be
harmless. They are mainly split out so that other branches can be
based on top to avoid conflicts.
Notable changes are:
- We finally remove all mach/timex.h, after CLOCK_TICK_RATE is no
longer used (Uwe Kleine-König)
- The Qualcomm MSM platform is split out into legacy mach-msm and
new-style mach-qcom, to allow easier maintainance of the new
hardware support without regressions (Kumar Gala)
- A rework of some of the Kconfig logic to simplify multiplatform
support (Rob Herring)
- Samsung Exynos gets closer to supporting multiplatform (Sachin
Kamat and others)
- mach-bcm3528 gets merged into mach-bcm (Stephen Warren)
- at91 gains some common clock framework support (Alexandre Belloni,
Jean-Jacques Hiblot and other French people)"
* tag 'cleanup-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (89 commits)
ARM: hisi: select HAVE_ARM_SCU only for SMP
ARM: efm32: allow uncompress debug output
ARM: prima2: build reset code standalone
ARM: at91: add PWM clock
ARM: at91: move sam9261 SoC to common clk
ARM: at91: prepare common clk transition for sam9261 SoC
ARM: at91: updated the at91_dt_defconfig with support for the ADS7846
ARM: at91: dt: sam9261: Device Tree support for the at91sam9261ek
ARM: at91: dt: defconfig: Added the sam9261 to the list of DT-enabled SOCs
ARM: at91: dt: Add at91sam9261 dt SoC support
ARM: at91: switch sam9rl to common clock framework
ARM: at91/dt: define main clk frequency of at91sam9rlek
ARM: at91/dt: define at91sam9rl clocks
ARM: at91: prepare common clk transition for sam9rl SoCs
ARM: at91: prepare sam9 dt boards transition to common clk
ARM: at91: dt: sam9rl: Device Tree for the at91sam9rlek
ARM: at91/defconfig: Add the sam9rl to the list of DT-enabled SOCs
ARM: at91: Add at91sam9rl DT SoC support
ARM: at91: prepare at91sam9rl DT transition
ARM: at91/defconfig: refresh at91sam9260_9g20_defconfig
...
My guess is we aren't going to have a 2 digit cpuid here any time soon
but the static checkers don't know that and complain that the snprintf()
could overflow.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Exynos5420 is octa-core SoC from Samsung. Hence extend exynos-mct clocksource
driver to support 8 local interrupts.
Also extend dts entries for 8 interrupts.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Some variants of Exynos MCT, namely exynos4210-mct at the moment, use
normal, shared interrupts for local timers. This means that each
interrupt must have correct affinity set to fire only on CPU
corresponding to given local timer.
However after recent conversion of clocksource drivers to not use the
local timer API for local timer initialization any more, the point of
time when local timers get initialized changed and irq_set_affinity()
fails because the CPU is not marked as online yet.
This patch fixes this by moving the call to irq_set_affinity() to
CPU_ONLINE notification, so the affinity is being set when the CPU goes
online.
This fixes a regression introduced by commit
ee98d27df6 ARM: EXYNOS4: Divorce mct from local timer API
which rendered all Exynos4210 based boards unbootable due to
failing irq_set_affinity() making local timers inoperatible.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
timer API entirely. Doing so will reduce code in ARM core, reduce the
architecture dependencies of our timer drivers, and simplify the code because
we no longer go through an architecture layer that is essentially a hotplug
notifier.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)
iQIcBAABCAAGBQJRydGwAAoJENidgRMleOc9tMMP/Awy0ETkLHQkXdFdRNLQH7Jd
BpDagzBkpt/U/qsh2Dy5Yhz7Qf/HQg6CwJK/b1apHguSPzNcSov+YS7ArPV+kuDY
9OCF5wkVqPW7BPHlxJ+2QAjayIFUaBR+35kpiU+hv9Gkhs11oK90iAWxEIDUGzA6
5miuOVJeyDEwV8des3NYmVVOKziHLJjX3fjMVnc2gxE6PLmOEUQ9t42bVU1aCfub
pRMUXNuG+aFk8lRExPfs4wWfEKCOHrgJPSE4OPFp3pDJeqhFi5tXTiPBQ22FpNf5
78fEDeguS0QS6f/3rGKSdGu/Yz5Lmcldv4tOkfzvNaZP7zhE18wKJu6bSCrZ/Onn
MnhriYWZh+YgX1V8wTMFMPEV+OR+FJdN4C8PhvNWmMC1Xoq25HtrVQUP5aElgAJs
mLcgTXxLYpvZH3jPxdtMR9IuDc+86qmFerGShWqp/1YaNHwpR8dNZxFyVNfw+FUL
/GoAjk/6MsJlZUchiF7I8yp4jYyMcXcV8Bi4tgIAf5rJO9PZBpuxtyAL9uVHnL13
pwkctMnMQwoP6AE9uYfbdnHCKJxF1hny4tKI5sNxAmK8I6bBkfibIZ3sNRAbSrY7
56kV+tJrrgvgAUDkgdluyS9eFs26iHGPsHK4lmzJzFylWmvWFa8tWpP6G0kCa0wP
A1XCqUOryLeL8enPV+z2
=wZbm
-----END PGP SIGNATURE-----
Merge tag 'remove-local-timers' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm into next/cleanup
From Stephen Boyd:
Now that we have a generic arch hook for broadcast we can remove the
local timer API entirely. Doing so will reduce code in ARM core, reduce
the architecture dependencies of our timer drivers, and simplify the code
because we no longer go through an architecture layer that is essentially
a hotplug notifier.
* tag 'remove-local-timers' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm:
ARM: smp: Remove local timer API
clocksource: time-armada-370-xp: Divorce from local timer API
clocksource: time-armada-370-xp: Fix sparse warning
ARM: msm: Divorce msm_timer from local timer API
ARM: PRIMA2: Divorce timer-marco from local timer API
ARM: EXYNOS4: Divorce mct from local timer API
ARM: OMAP2+: Divorce from local timer API
ARM: smp_twd: Divorce smp_twd from local timer API
ARM: smp: Remove duplicate dummy timer implementation
Resolved a large number of conflicts due to __cpuinit cleanups, etc.
Signed-off-by: Olof Johansson <olof@lixom.net>
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications. For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.
After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out. Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.
This removes all the drivers/clocksource and drivers/irqchip uses of
the __cpuinit macros from all C files.
[1] https://lkml.org/lkml/2013/5/20/589
Cc: John Stultz <john.stultz@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Separate the mct local timers from the local timer API. This will
allow us to remove ARM local timer support in the near future and
gets us closer to moving this driver to drivers/clocksource.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Replace the (setup/remove)_irq calls for local timer registration with
(request/free)_irq calls. This generalizes the local timer registration API.
Suggested by Mark Rutland.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
These continue the multiplatform support for exynos, adding support
for building most of the essential drivers (clocksource, clk, irqchip)
when combined with other platforms. As a result, it should become
really easy to add full multiplatform exynos support in 3.11, although
we don't yet enable it for 3.10.
The changes were not included in the earlier multiplatform series
in order to avoid clashes with the other Exynos updates.
This also includes work from Tomasz Figa to fix the pwm clocksource
code on Exynos, which is not strictly required for multiplatform,
but related to the other patches in this set and needed as a bug
fix for at least one board.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=FY7+
-----END PGP SIGNATURE-----
Merge tag 'multiplatform-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull late ARM Exynos multiplatform changes from Arnd Bergmann:
"These continue the multiplatform support for exynos, adding support
for building most of the essential drivers (clocksource, clk, irqchip)
when combined with other platforms. As a result, it should become
really easy to add full multiplatform exynos support in 3.11, although
we don't yet enable it for 3.10.
The changes were not included in the earlier multiplatform series in
order to avoid clashes with the other Exynos updates.
This also includes work from Tomasz Figa to fix the pwm clocksource
code on Exynos, which is not strictly required for multiplatform, but
related to the other patches in this set and needed as a bug fix for
at least one board."
* tag 'multiplatform-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (22 commits)
ARM: dts: exynops4210: really add universal_c210 dts
ARM: dts: exynos4210: Add basic dts file for universal_c210 board
ARM: dts: exynos4: Add node for PWM device
ARM: SAMSUNG: Do not register legacy timer interrupts on Exynos
clocksource: samsung_pwm_timer: Work around rounding errors in clockevents core
clocksource: samsung_pwm_timer: Correct programming of clock events
clocksource: samsung_pwm_timer: Use proper clockevents max_delta
clocksource: samsung_pwm_timer: Add support for non-DT platforms
clocksource: samsung_pwm_timer: Drop unused samsung_pwm struct
clocksource: samsung_pwm_timer: Keep all driver data in a structure
clocksource: samsung_pwm_timer: Make PWM spinlock global
clocksource: samsung_pwm_timer: Let platforms select the driver
Documentation: Add device tree bindings for Samsung PWM timers
clocksource: add samsung pwm timer driver
irqchip: exynos: look up irq using irq_find_mapping
irqchip: exynos: pass irq_base from platform
irqchip: exynos: localize irq lookup for ATAGS
irqchip: exynos: allocate combiner_data dynamically
irqchip: exynos: pass max combiner number to combiner_init
ARM: exynos: add missing properties for combiner IRQs
...
These are cleanups and smaller changes that either depend on earlier
feature branches or came in late during the development cycle.
We normally try to get all cleanups early, so these are the exceptions:
- A follow-up on the clocksource reworks, hopefully the last time
we need to merge clocksource subsystem changes through arm-soc.
A first set of patches was part of the original 3.10 arm-soc cleanup
series because of interdependencies with timer drivers now moved out
of arch/arm.
- Migrating the SPEAr13xx platform away from using auxdata for DMA
channel descriptions towards using information in device tree,
based on the earlier SPEAr multiplatform series
- A few follow-ups on the Atmel SAMA5 support and other changes
for Atmel at91 based on the larger at91 reworks.
- Moving the armada irqchip implementation to drivers/irqchip
- Several OMAP cleanups following up on the larger series already
merged in 3.10.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=HWfp
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late cleanups from Arnd Bergmann:
"These are cleanups and smaller changes that either depend on earlier
feature branches or came in late during the development cycle. We
normally try to get all cleanups early, so these are the exceptions:
- A follow-up on the clocksource reworks, hopefully the last time we
need to merge clocksource subsystem changes through arm-soc.
A first set of patches was part of the original 3.10 arm-soc
cleanup series because of interdependencies with timer drivers now
moved out of arch/arm.
- Migrating the SPEAr13xx platform away from using auxdata for DMA
channel descriptions towards using information in device tree,
based on the earlier SPEAr multiplatform series
- A few follow-ups on the Atmel SAMA5 support and other changes for
Atmel at91 based on the larger at91 reworks.
- Moving the armada irqchip implementation to drivers/irqchip
- Several OMAP cleanups following up on the larger series already
merged in 3.10."
* tag 'cleanup-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (50 commits)
ARM: OMAP4: change the device names in usb_bind_phy
ARM: OMAP2+: Fix mismerge for timer.c between ff931c82 and da4a686a
ARM: SPEAr: conditionalize SMP code
ARM: arch_timer: Silence debug preempt warnings
ARM: OMAP: remove unused variable
serial: amba-pl011: fix !CONFIG_DMA_ENGINE case
ata: arasan: remove the need for platform_data
ARM: at91/sama5d34ek.dts: remove not needed compatibility string
ARM: at91: dts: add MCI DMA support
ARM: at91: dts: add i2c dma support
ARM: at91: dts: set #dma-cells to the correct value
ARM: at91: suspend both memory controllers on at91sam9263
irqchip: armada-370-xp: slightly cleanup irq controller driver
irqchip: armada-370-xp: move IRQ handler to avoid forward declaration
irqchip: move IRQ driver for Armada 370/XP
ARM: mvebu: move L2 cache initialization in init_early()
devtree: add binding documentation for sp804
ARM: integrator-cp: convert use CLKSRC_OF for timer init
ARM: versatile: use OF init for sp804 timer
ARM: versatile: add versatile dtbs to dtbs target
...
Will Deacon