In two dca files copyright and license headers are missing.
This patch adds them there.
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
reorder struct inet6_ifaddr to remove padding on 64 bit builds
remove 8 bytes of padding so inet6_ifaddr becomes 192 bytes & fits into
a smaller slab.
Signed-off-by: Richard Kennedy <richard@rsk.demon.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_queue_xmit() needs to dirty fields "state", "q", "bstats" and "qstats"
On x86_64 arch, they currently span three cache lines, involving more
cache line ping pongs than necessary, making longer holding of queue spinlock.
We can reduce this to one cache line, by grouping all read-mostly fields
at the beginning of structure. (Or should I say, all highly modified fields
at the end :) )
Before patch :
offsetof(struct Qdisc, state)=0x38
offsetof(struct Qdisc, q)=0x48
offsetof(struct Qdisc, bstats)=0x80
offsetof(struct Qdisc, qstats)=0x90
sizeof(struct Qdisc)=0xc8
After patch :
offsetof(struct Qdisc, state)=0x80
offsetof(struct Qdisc, q)=0x88
offsetof(struct Qdisc, bstats)=0xa0
offsetof(struct Qdisc, qstats)=0xac
sizeof(struct Qdisc)=0xc0
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To improve manageability, it would be good to be able to disambiguate routes
added by administrator from those added by DHCP client. The only necessary
kernel change is to add value to rtnetlink include file so iproute2 utility
can use it.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a port's link is down (except to driver restart) and the port is
configured for auto sensing, we try to sense port link type (Ethernet
or InfiniBand) in order to determine how to initialize the port. If
the port type needs to be changed, all mlx4 for the device interfaces
are unregistered and then registered again with the new port
types. Sensing is done with intervals of 3 seconds.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Since creating a device node is normally an operation requiring special
privilege, Igor Zhbanov points out that it is surprising (to say the
least) that a client can, for example, create a device node on a
filesystem exported with root_squash.
So, make sure CAP_MKNOD is among the capabilities dropped when an nfsd
thread handles a request from a non-root user.
Reported-by: Igor Zhbanov <izh1979@gmail.com>
Cc: stable@kernel.org
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
It depends on L3 support from 2.4 kernel (CONFIG_L3) that never got
merged into mainline. Since there's no way to use it on any of
supported machines (iPaq h3100 or h3600), better drop it for now.
It can be reimplemented later using ASoC infrastructure (there's
already a driver for uda1341 codec in mainline, so only CPU and machine
parts need to be written).
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This allows us to send to userspace "regulatory" events.
For now we just send an event when we change regulatory domains.
We also notify userspace when devices are using their own custom
world roaming regulatory domains.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We do this so we can later inform userspace who set the
regulatory domain and provide details of the request.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is not used as we can always just assume the first
regulatory domain set will _always_ be a static regulatory
domain. REGDOM_SET_BY_CORE will be the first request from
cfg80211 for a regdomain and that then populates the first
regulatory request.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As my netpoll fix for net doesn't really work for net-next, we
need this update to move the checks into the right place. As it
stands we may pass freed skbs to netpoll_receive_skb.
This patch also introduces a netpoll_rx_on function to avoid GRO
completely if we're invoked through netpoll. This might seem
paranoid but as netpoll may have an external receive hook it's
better to be safe than sorry. I don't think we need this for
2.6.29 though since there's nothing immediately broken by it.
This patch also moves the GRO_* return values to netdevice.h since
VLAN needs them too (I tried to avoid this originally but alas
this seems to be the easiest way out). This fixes a bug in VLAN
where it continued to use the old return value 2 instead of the
correct GRO_DROP.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the iptables cluster match. This match can be used
to deploy gateway and back-end load-sharing clusters. The cluster
can be composed of 32 nodes maximum (although I have only tested
this with two nodes, so I cannot tell what is the real scalability
limit of this solution in terms of cluster nodes).
Assuming that all the nodes see all packets (see below for an
example on how to do that if your switch does not allow this), the
cluster match decides if this node has to handle a packet given:
(jhash(source IP) % total_nodes) & node_mask
For related connections, the master conntrack is used. The following
is an example of its use to deploy a gateway cluster composed of two
nodes (where this is the node 1):
iptables -I PREROUTING -t mangle -i eth1 -m cluster \
--cluster-total-nodes 2 --cluster-local-node 1 \
--cluster-proc-name eth1 -j MARK --set-mark 0xffff
iptables -A PREROUTING -t mangle -i eth1 \
-m mark ! --mark 0xffff -j DROP
iptables -A PREROUTING -t mangle -i eth2 -m cluster \
--cluster-total-nodes 2 --cluster-local-node 1 \
--cluster-proc-name eth2 -j MARK --set-mark 0xffff
iptables -A PREROUTING -t mangle -i eth2 \
-m mark ! --mark 0xffff -j DROP
And the following commands to make all nodes see the same packets:
ip maddr add 01:00:5e:00:01:01 dev eth1
ip maddr add 01:00:5e:00:01:02 dev eth2
arptables -I OUTPUT -o eth1 --h-length 6 \
-j mangle --mangle-mac-s 01:00:5e:00:01:01
arptables -I INPUT -i eth1 --h-length 6 \
--destination-mac 01:00:5e:00:01:01 \
-j mangle --mangle-mac-d 00:zz:yy:xx:5a:27
arptables -I OUTPUT -o eth2 --h-length 6 \
-j mangle --mangle-mac-s 01:00:5e:00:01:02
arptables -I INPUT -i eth2 --h-length 6 \
--destination-mac 01:00:5e:00:01:02 \
-j mangle --mangle-mac-d 00:zz:yy:xx:5a:27
In the case of TCP connections, pickup facility has to be disabled
to avoid marking TCP ACK packets coming in the reply direction as
valid.
echo 0 > /proc/sys/net/netfilter/nf_conntrack_tcp_loose
BTW, some final notes:
* This match mangles the skbuff pkt_type in case that it detects
PACKET_MULTICAST for a non-multicast address. This may be done in
a PKTTYPE target for this sole purpose.
* This match supersedes the CLUSTERIP target.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Commit 784544739a (netfilter: iptables:
lock free counters) broke a number of modules whose rule data referenced
itself. A reallocation would not reestablish the correct references, so
it is best to use a separate struct that does not fall under RCU.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Traditionally, changes to struct file->f_flags have been done under BKL
protection, or with no protection at all. This patch causes all f_flags
changes after file open/creation time to be done under protection of
f_lock. This allows the removal of some BKL usage and fixes a number of
longstanding (if microscopic) races.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This lock moves out of the CONFIG_EPOLL ifdef and becomes f_lock. For now,
epoll remains the only user, but a future patch will use it to protect
f_flags as well.
Cc: Davide Libenzi <davidel@xmailserver.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This patch skips the delivery of conntrack events if the packet
was drop due to a race condition in the conntrack insertion.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch modifies nf_log to use a linked list of loggers for each
protocol. This list of loggers is read and write protected with a
mutex.
This patch separates registration and binding. To be used as
logging module, a module has to register calling nf_log_register()
and to bind to a protocol it has to call nf_log_bind_pf().
This patch also converts the logging modules to the new API. For nfnetlink_log,
it simply switchs call to register functions to call to bind function and
adds a call to nf_log_register() during init. For other modules, it just
remove a const flag from the logger structure and replace it with a
__read_mostly.
Signed-off-by: Eric Leblond <eric@inl.fr>
Signed-off-by: Patrick McHardy <kaber@trash.net>
The results is very unlikely change every so often so we
hardly need to divide again after doing that once for a
connection. Yet, if divide still becomes necessary we
detect that and do the right thing and again settle for
non-divide state. Takes the u16 space which was previously
taken by the plain xmit_size_goal.
This should take care part of the tso vs non-tso difference
we found earlier.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's very little need for most of the callsites to get
tp->xmit_goal_size updated. That will cost us divide as is,
so slice the function in two. Also, the only users of the
tp->xmit_goal_size are directly behind tcp_current_mss(),
so there's no need to store that variable into tcp_sock
at all! The drop of xmit_goal_size currently leaves 16-bit
hole and some reorganization would again be necessary to
change that (but I'm aiming to fill that hole with u16
xmit_goal_size_segs to cache the results of the remaining
divide to get that tso on regression).
Bring xmit_goal_size parts into tcp.c
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wow, it was quite tricky to merge that stream of negations
but I think I finally got it right:
check & replace_ts_recent:
(s32)(rcv_tsval - ts_recent) >= 0 => 0
(s32)(ts_recent - rcv_tsval) <= 0 => 0
discard:
(s32)(ts_recent - rcv_tsval) > TCP_PAWS_WINDOW => 1
(s32)(ts_recent - rcv_tsval) <= TCP_PAWS_WINDOW => 0
I toggled the return values of tcp_paws_check around since
the old encoding added yet-another negation making tracking
of truth-values really complicated.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
On x86_64, its rather unfortunate that "wait_queue_head_t wait"
field of "struct socket" spans two cache lines (assuming a 64
bytes cache line in current cpus)
offsetof(struct socket, wait)=0x30
sizeof(wait_queue_head_t)=0x18
This might explain why Kenny Chang noticed that his multicast workload
was performing bad with 64 bit kernels, since more cache lines ping pongs
were involved.
This litle patch moves "wait" field next "fasync_list" so that both
fields share a single cache line, to speedup sock_def_readable()
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* master.kernel.org:/home/rmk/linux-2.6-arm: (23 commits)
[ARM] Fix virtual to physical translation macro corner cases
[ARM] update mach-types
[ARM] 5421/1: ftrace: fix crash due to tracing of __naked functions
MX1 fix include
[ARM] 5419/1: ep93xx: fix build warnings about struct i2c_board_info
[ARM] 5418/1: restore lr before leaving mcount
ARM: OMAP: board-omap3beagle: set i2c-3 to 100kHz
ARM: OMAP: Allow I2C bus driver to be compiled as a module
ARM: OMAP: sched_clock() corrected
ARM: OMAP: Fix compile error if pm.h is included
[ARM] orion5x: pass dram mbus data to xor driver
[ARM] S3C64XX: Fix s3c64xx_setrate_clksrc
[ARM] S3C64XX: sparse warnings in arch/arm/plat-s3c64xx/irq.c
[ARM] S3C64XX: sparse warnings in arch/arm/plat-s3c64xx/s3c6400-clock.c
[ARM] S3C64XX: Fix USB host clock mux list
[ARM] S3C64XX: Fix name of USB host clock.
[ARM] S3C64XX: Rename IRQ_UHOST to IRQ_USBH
[ARM] S3C64XX: Do gpiolib configuration earlier
[ARM] S3C64XX: Staticise s3c64xx_init_irq_eint()
[ARM] SMDK6410: Declare iodesc table static
...
As the PXA27x series allow 2 gpios to reset the ac97 bus,
allow through platform data configuration the definition of
the correct gpio which will reset the AC97 bus.
This comes from a silicon defect on the PXA27x series, where
the gpio must be manually controlled in warm reset cases.
Signed-off-by: Robert Jarzmik <rjarzmik@free.fr>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Stricter gfp_mask might be required for clone allocation.
For example, request-based dm may clone bio in interrupt context
so it has to use GFP_ATOMIC.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6: (31 commits)
[SCSI] qla2xxx: Update version number to 8.03.00-k4.
[SCSI] qla2xxx: Correct overwrite of pre-assigned init-control-block structure size.
[SCSI] qla2xxx: Correct truncation in return-code status checking.
[SCSI] qla2xxx: Correct vport delete bug.
[SCSI] qla2xxx: Use correct value for max vport in LOOP topology.
[SCSI] qla2xxx: Correct address range checking for option-rom updates.
[SCSI] fcoe: Change fcoe receive thread nice value from 19 (lowest priority) to -20
[SCSI] fcoe: fix handling of pending queue, prevent out of order frames (v3)
[SCSI] fcoe: Out of order tx frames was causing several check condition SCSI status
[SCSI] fcoe: fix kfree(skb)
[SCSI] fcoe: ETH_P_8021Q is already in if_ether and fcoe is not using it anyway
[SCSI] libfc: do not change the fh_rx_id of a recevied frame
[SCSI] fcoe: Correct fcoe_transports initialization vs. registration
[SCSI] fcoe: Use setup_timer() and mod_timer()
[SCSI] libfc, fcoe: Remove unnecessary cast by removing inline wrapper
[SCSI] libfc, fcoe: Cleanup function formatting and minor typos
[SCSI] libfc, fcoe: Fix kerneldoc comments
[SCSI] libfc: Cleanup libfc_function_template comments
[SCSI] libfc: check for err when recv and state is incorrect
[SCSI] libfc: rename rp to rdata in fc_disc_new_target()
...
* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
NFS: Fix the fix to Bugzilla #11061, when IPv6 isn't defined...
SUNRPC: xprt_connect() don't abort the task if the transport isn't bound
SUNRPC: Fix an Oops due to socket not set up yet...
Bug 11061, NFS mounts dropped
NFS: Handle -ESTALE error in access()
NLM: Fix GRANT callback address comparison when IPv6 is enabled
NLM: Shrink the IPv4-only version of nlm_cmp_addr()
NFSv3: Fix posix ACL code
NFS: Fix misparsing of nfsv4 fs_locations attribute (take 2)
SUNRPC: Tighten up the task locking rules in __rpc_execute()
I found the PPP subsystem to not work properly when connecting channels
with different speeds to the same bundle.
Problem Description:
As the "ppp_mp_explode" function fragments the sk_buff buffer evenly
among the PPP channels that are connected to a certain PPP unit to
make up a bundle, if we are transmitting using an upper layer protocol
that requires an Ack before sending the next packet (like TCP/IP for
example), we will have a bandwidth bottleneck on the slowest channel
of the bundle.
Let's clarify by an example. Let's consider a scenario where we have
two PPP links making up a bundle: a slow link (10KB/sec) and a fast
link (1000KB/sec) working at the best (full bandwidth). On the top we
have a TCP/IP stack sending a 1000 Bytes sk_buff buffer down to the
PPP subsystem. The "ppp_mp_explode" function will divide the buffer in
two fragments of 500B each (we are neglecting all the headers, crc,
flags etc?.). Before the TCP/IP stack sends out the next buffer, it
will have to wait for the ACK response from the remote peer, so it
will have to wait for both fragments to have been sent over the two
PPP links, received by the remote peer and reconstructed. The
resulting behaviour is that, rather than having a bundle working
@1010KB/sec (the sum of the channels bandwidths), we'll have a bundle
working @20KB/sec (the double of the slowest channels bandwidth).
Problem Solution:
The problem has been solved by redesigning the "ppp_mp_explode"
function in such a way to make it split the sk_buff buffer according
to the speeds of the underlying PPP channels (the speeds of the serial
interfaces respectively attached to the PPP channels). Referring to
the above example, the redesigned "ppp_mp_explode" function will now
divide the 1000 Bytes buffer into two fragments whose sizes are set
according to the speeds of the channels where they are going to be
sent on (e.g . 10 Byets on 10KB/sec channel and 990 Bytes on
1000KB/sec channel). The reworked function grants the same
performances of the original one in optimal working conditions (i.e. a
bundle made up of PPP links all working at the same speed), while
greatly improving performances on the bundles made up of channels
working at different speeds.
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It closes a race in phy_stop_machine when reprogramming of phy_timer
(from phy_state_machine) happens between del_timer_sync and cancel_work_sync.
Without this change it could lead to crash if phy_device would be freed after
phy_stop_machine (timer would fire and schedule freed work).
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
dma_map_sg could return a value different to 'nents' argument of
dma_map_sg so the ide stack needs to save it for the later usage
(e.g. for_each_sg).
The ide stack also needs to save the original sg_nents value for
pci_unmap_sg.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
[bart: backport to Linus' tree]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Impact: documentation
struct irqaction is not documented. Add kernel doc comments and add
interrupt.h to the genirq docbook.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
cpumask: mm_cpumask for accessing the struct mm_struct's cpu_vm_mask.
cpumask: tsk_cpumask for accessing the struct task_struct's cpus_allowed.
This is a fix for the following crash observed in 2.6.29-rc3:
http://lkml.org/lkml/2009/1/29/150
On ARM it doesn't make sense to trace a naked function because then
mcount is called without stack and frame pointer being set up and there
is no chance to restore the lr register to the value before mcount was
called.
Reported-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Tested-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Cc: Abhishek Sagar <sagar.abhishek@gmail.com>
Cc: Steven Rostedt <rostedt@home.goodmis.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Modify remove_irq() to match setup_irq().
Signed-off-by: Magnus Damm <damm@igel.co.jp>
LKML-Reference: <20090312120551.2926.43942.sendpatchset@rx1.opensource.se>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: add new API
This patch adds a remove_irq() function for releasing
interrupts requested with setup_irq().
Without this patch we have no way of releasing such
interrupts since free_irq() today tries to kfree()
the irqaction passed with setup_irq().
Signed-off-by: Magnus Damm <damm@igel.co.jp>
LKML-Reference: <20090312120542.2926.56609.sendpatchset@rx1.opensource.se>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This allows us to change the representation (to a dangling bitmap or
cpumask_var_t) without breaking all the callers: they can use
mm_cpumask() now and won't see a difference as the changes roll into
linux-next.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This allows us to change the representation (to a dangling bitmap or
cpumask_var_t) without breaking all the callers: they can use
tsk_cpumask() now and won't see a difference as the changes roll into
linux-next.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Merge Eric Maio's patch to merge snd_soc_dai_ops out of line. Fixed
merge issues and updated drivers, plus an issue with the ops for the two
s3c2443 AC97 DAIs having been merged.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8400 is a highly integrated audio CODEC and power management unit
intended for mobile multimedia application. This driver supports the
primary audio CODEC features, including:
- 1W speaker driver
- Fully differential headphone output
- Up to 4 differential microphone inputs
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use define instead of enum for ioctl definitions since strace can't
parse ioctls defined via enum properly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Comparing the layouts of struct detail_pixel_timing with
x.org's struct detailed_timings and how those are handled,
it appears that the hsync_positive and vsync_positive
fields are backwards.
This patch fixes https://bugs.freedesktop.org/show_bug.cgi?id=20019
for me. It was tested on 2 monitors, LG FLATRON L225WS 22" and
a YAKUMO 17" for which more details are unknown.
Signed-off-by: Pantelis Koukousoulas <pktoss@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Clean up/micro-optimatization: Make the AF_INET-only version of
nlm_cmp_addr() smaller. This matches the style of
nlm_privileged_requester(), and makes the AF_INET-only version of
nlm_cmp_addr() nearly the same size as it was before IPv6 support.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Fix a memory leak due to allocation in the XDR layer. In cases where the
RPC call needs to be retransmitted, we end up allocating new pages without
clearing the old ones. Fix this by moving the allocation into
nfs3_proc_setacls().
Also fix an issue discovered by Kevin Rudd, whereby the amount of memory
reserved for the acls in the xdr_buf->head was miscalculated, and causing
corruption.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
frames followed by these errors in log.
[sdp] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
[sdp] Sense Key : Aborted Command [current]
[sdp] Add. Sense: Data phase error
This was causing some test apps to exit due to write failure under heavy
load.
This was due to a race around adding and removing tx frame skb in
fcoe_pending_queue, Chris Leech helped me to find that brief unlocking
period when pulling skb from fcoe_pending_queue in various contexts
(fcoe_watchdog and fcoe_xmit) and then adding skb back into fcoe_pending_queue
up on a failed fcoe_start_io could change skb/tx frame order in
fcoe_pending_queue. Thanks Chris.
This patch allows only single context to pull skb from fcoe_pending_queue
at any time to prevent above described ordering issue/race by use of
fcoe_pending_queue_active flag.
This patch simplified fcoe_watchdog with modified fcoe_check_wait_queue by
use of FCOE_LOW_QUEUE_DEPTH instead previously used several conditionals
to clear and set lp->qfull.
I think FCOE_MAX_QUEUE_DEPTH with FCOE_LOW_QUEUE_DEPTH will work better
in re/setting lp->qfull and these could be fine tuned for performance.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Comment from "Andrew Morton <akpm@linux-foundation.org>"
> +{
> + return (struct fcoe_softc *)lport_priv(lp);
unneeded/undesirable cast of void*. There are probably zillions of
instances of this - there always are.
This whole inline function was unnecessary. The FCoE layer knows
that it's data structure is stored in the lport private data, it
can just access it from lport_priv().
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
1) Added '()' for function names in kerneldoc comments
2) Changed comment bookends from '**/' to '*/'. The comment on the the
mailing list was that '**/' "is consistently unconventional. Not
wrong, just odd." The Documentation/kernel-doc-nano-HOWTO.txt
states that kerneldoc comment blocks should end with '**/' but most
(if not all) instance I found under drivers/scsi/ were only using
the '*/' so I converted to that style.
3) Removed incorrect linebreaks in kerneldoc comments where found
4) Removed a few unnecessary blank comment lines in kerneldoc comment
blocks
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This reverts commit e088e4c9cd.
Removing the sysfs interface for p4-clockmod was flagged as a
regression in bug 12826.
Course of action:
- Find out the remaining causes of overheating, and fix them
if possible. ACPI should be doing the right thing automatically.
If it isn't, we need to fix that.
- mark p4-clockmod ui as deprecated
- try again with the removal in six months.
It's not really feasible to printk about the deprecation, because
it needs to happen at all the sysfs entry points, which means adding
a lot of strcmp("p4-clockmod".. calls to the core, which.. bleuch.
Signed-off-by: Dave Jones <davej@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (29 commits)
p54: fix race condition in memory management
cfg80211: test before subtraction on unsigned
iwlwifi: fix error flow in iwl*_pci_probe
rt2x00 : more devices to rt73usb.c
rt2x00 : more devices to rt2500usb.c
bonding: Fix device passed into ->ndo_neigh_setup().
vlan: Fix vlan-in-vlan crashes.
net: Fix missing dev->neigh_setup in register_netdevice().
tmspci: fix request_irq race
pkt_sched: act_police: Fix a rate estimator test.
tg3: Fix 5906 link problems
SCTP: change sctp_ctl_sock_init() to try IPv4 if IPv6 fails
IPv6: add "disable" module parameter support to ipv6.ko
sungem: another error printed one too early
aoe: error printed 1 too early
net pcmcia: worklimit reaches -1
net: more timeouts that reach -1
net: fix tokenring license
dm9601: new vendor/product IDs
netlink: invert error code in netlink_set_err()
...
Use the standard linked list for snd_monitor_file management.
Also, move the list deletion of shutdown_list element into
snd_disconnect_release() (for simplification).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added snd_ctl_add_slave_uncached() function to add a slave element
with volatile controls. The values of normal slave elements are
supposed to be cachable, i.e. they are changed only via the put
callbacks. OTOH, when a slave element is volatile and its values may
be changed by other reason (e.g. hardware status change), the values
will get inconsistent.
The new function allows the slave elements with volatile changes.
When the slave is tied with this call, the native get callback is
issued at each time so that the values are always updated.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The timer callbacks are called in the protected status by the lock
of the timer instance, so there is no need for an extra lock in the
PCM substream.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
dmatest: fix use after free in dmatest_exit
ipu_idmac: fix spinlock type
iop-adma, mv_xor: fix mem leak on self-test setup failure
fsldma: fix off by one in dma_halt
I/OAT: fail self-test if callback test reaches timeout
I/OAT: update driver version and copyright dates
I/OAT: list usage cleanup
I/OAT: set tcp_dma_copybreak to 256k for I/OAT ver.3
I/OAT: cancel watchdog before dma remove
I/OAT: fail initialization on zero channels detection
I/OAT: do not set DCACTRL_CMPL_WRITE_ENABLE for I/OAT ver.3
I/OAT: add verification for proper APICID_TAG_MAP setting by BIOS
dmaengine: update kerneldoc
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
ata: add CFA specific identify data words
remove stale comment from <linux/hdreg.h>
AT91: initialize Compact Flash on AT91SAM9263 cpu
ide: add at91_ide driver
ide: allow to wrap interrupt handler
ide-iops: fix odd-length ATAPI PIO transfers
ide: NULL noise: drivers/ide/ide-*.c
ide: expiry() returns int, negative expiry() return values won't be noticed
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: Don't trust current capacity values in identify words 57-58
libata: make sure port is thawed when skipping resets
sata_nv: fix module parameter description
ahci: Add the Device IDs for MCP89 and remove IDs of MCP7B to/from ahci.c
libata: don't use on-stack sense buffer
libata: align ap->sector_buf
libata: fix dma_unmap_sg misuse
libata: change drive ready wait after hard reset to 5s
Protocol 0x37 has been reserved for iNexio devices and Sahara
was supposed to get 0x38.
Reported-by: Claudio Nieder <private@claudio.ch>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Made the comments more like the comments for struct scsi_host_template.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This allows any rport ELS to retry on LS_RJT.
The rport error handling would only retry on resource allocation failures
and exchange timeouts. I have a target that will occasionally reject PLOGI
when we do a quick LOGO/PLOGI. When a critical ELS was rejected, libfc would
fail silently leaving the rport in a dead state.
The retry count and delay are managed by fc_rport_error_retry. If the retry
count is exceeded fc_rport_error will be called. When retrying is not the
correct course of action, fc_rport_error can be called directly.
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The fcoe_xmit could call fc_pause in case the pending skb queue len is larger
than FCOE_MAX_QUEUE_DEPTH, the fc_pause was trying to grab lport->lp_muex to
change lport->link_status and that had these issues :-
1. The fcoe_xmit was getting called with bh disabled, thus causing
"BUG: scheduling while atomic" when grabbing lport->lp_muex with bh disabled.
2. fc_linkup and fc_linkdown function calls lport_enter function with
lport->lp_mutex held and these enter function in turn calls fcoe_xmit to send
lport related FC frame, e.g. fc_linkup => fc_lport_enter_flogi to send flogi
req. In this case grabbing the same lport->lp_mutex again in fc_puase from
fcoe_xmit would cause deadlock.
The lport->lp_mutex was used for setting FC_PAUSE in fcoe_xmit path but
FC_PAUSE bit was not used anywhere beside just setting and clear this
bit in lport->link_status, instead used a separate field qfull in fc_lport
to eliminate need for lport->lp_mutex to track pending queue full condition
and in turn avoid above described two locking issues.
Also added check for lp->qfull in fc_fcp_lport_queue_ready to trigger
SCSI_MLQUEUE_HOST_BUSY when lp->qfull is set to prevent more scsi-ml cmds
while lp->qfull is set.
This patch eliminated FC_LINK_UP and FC_PAUSE and instead used dedicated
fields in fc_lport for this, this simplified all related conditional
code.
Also removed fc_pause and fc_unpause functions and instead used newly added
lport->qfull directly in fcoe.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
fc_exch_mgr structure is private to fc_exch.c. To export exch_mgr_reset to
transport, transport needs access to the exch manager. Change
exch_mgr_reset to use lport param which is the shared structure between
libFC and transport.
Alternatively, fc_exch_mgr definition can be moved to libfc.h so that lport
can be accessed from mp*.
Signed-off-by: Abhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This adds SSB functionality to register a fallback SPROM image from the
architecture setup code.
Weird architectures exist that have half-assed SSB devices without SPROM attached to
their PCI busses. The architecture can register a fallback SPROM image that is
used if no SPROM is found on the SSB device.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: Florian Fainelli <florian@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Declare CFA specific identify data words 162 and 163 for future use.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
[bart: update patch summary/description]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
ap->sector_buf is used as DMA target and should at least be aligned on
cacheline. This caused problems on some embedded machines.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
libata passes the returned value of dma_map_sg() to
dma_unmap_sg(),which is the misuse of dma_unmap_sg().
DMA-mapping.txt says:
To unmap a scatterlist, just call:
pci_unmap_sg(pdev, sglist, nents, direction);
Again, make sure DMA activity has already finished.
PLEASE NOTE: The 'nents' argument to the pci_unmap_sg call must be
the _same_ one you passed into the pci_map_sg call,
it should _NOT_ be the 'count' value _returned_ from the
pci_map_sg call.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This fixes problems during resume with drives that take longer than 1s to
be ready. The ATA-6 spec appears to allow 5 seconds for a drive to be
ready.
On one affected system, this patch changes "PM: resume devices took..."
message from 17 seconds to 4 seconds, and gets rid of a lot of ugly
timeout/error messages.
Without this patch, the libata code moves on after 1s, tries to send a
soft reset (which the drive doesn't see because it isn't ready) which also
times out, then an IDENTIFY command is sent to the drive which times out,
and finally the error handler will try to send another hard reset which
will finally get things working.
Signed-off-by: Stuart Hayes <stuart_hayes@dell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Move the IIS headers to their correct place.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
As analyzed by Patrick McHardy, vlan needs to reset it's
netdev_ops pointer in it's ->init() function but this
leaves the compat method pointers stale.
Add a netdev_resync_ops() and call it from the vlan code.
Any other driver which changes ->netdev_ops after register_netdevice()
will need to call this new function after doing so too.
With help from Patrick McHardy.
Tested-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Considering the fact that most cpu_dai or codec_dai are using a same
'snd_soc_dai_ops' for several similar interfaces, 'ops' would be better
made a pointer instead, to make sharing easier and code a bit cleaner.
The patch below is rather preliminary since the asoc tree is being
actively developed, and this touches almost every piece of code,
(and possibly many others in development need to be changed as
well). Building of all codecs are OK, yet to every SoC, I didn't test
that.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add GPIO support to jack reporting framework in ASoC using gpiolib calls.
The gpio support exports two new functions: snd_soc_jack_add_gpios and
snd_soc_jack_free_gpios.
Client drivers using gpio feature must pass an array of jack_gpio pins
belonging to a specific jack to the snd_soc_jack_add_gpios function. The
framework will request the gpios, set the data direction and request irq.
The framework will update power status of related jack_pins when an event on
the gpio pins comes according to the reporting bits defined for each gpio.
All gpio resources allocated when adding jack_gpio pins can be released
using snd_soc_jack_free_gpios function.
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently it is possible to do just about everything with the arp table
from user space except treat an entry like you are using it. To that end
implement and a flag NTF_USE that when set in a netwlink update request
treats the neighbour table entry like the kernel does on the output path.
This allows user space applications to share the kernel's arp cache.
Signed-off-by: Eric Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current "comp" crypto interface supports one-shot (de)compression only,
i.e. the whole data buffer to be (de)compressed must be passed at once, and
the whole (de)compressed data buffer will be received at once.
In several use-cases (e.g. compressed file systems that store files in big
compressed blocks), this workflow is not suitable.
Furthermore, the "comp" type doesn't provide for the configuration of
(de)compression parameters, and always allocates workspace memory for both
compression and decompression, which may waste memory.
To solve this, add a "pcomp" partial (de)compression interface that provides
the following operations:
- crypto_compress_{init,update,final}() for compression,
- crypto_decompress_{init,update,final}() for decompression,
- crypto_{,de}compress_setup(), to configure (de)compression parameters
(incl. allocating workspace memory).
The (de)compression methods take a struct comp_request, which was mimicked
after the z_stream object in zlib, and contains buffer pointer and length
pairs for input and output.
The setup methods take an opaque parameter pointer and length pair. Parameters
are supposed to be encoded using netlink attributes, whose meanings depend on
the actual (name of the) (de)compression algorithm.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: don't allow setuid to succeed if the user does not have rt bandwidth
sched_rt: don't start timer when rt bandwidth disabled
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
rcu: Teach RCU that idle task is not quiscent state at boot
It turns out that net_alive is unnecessary, and the original problem
that led to it being added was simply that the icmp code thought
it was a network device and wound up being unable to handle packets
while there were still packets in the network namespace.
Now that icmp and tcp have been fixed to properly register themselves
this problem is no longer present and we have a stronger guarantee
that packets will not arrive in a network namespace then that provided
by net_alive in netif_receive_skb. So remove net_alive allowing
packet reception run a little faster.
Additionally document the strong reason why network namespace cleanup
is safe so that if something happens again someone else will have
a chance of figuring it out.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit faee47cdbf
(sctp: Fix the RTO-doubling on idle-link heartbeats)
broke the RTO doubling for data retransmits. If the
heartbeat was sent before the data T3-rtx time, the
the RTO will not double upon the T3-rtx expiration.
Distingish between the operations by passing an argument
to the function.
Additionally, Wei Youngjun pointed out that our treatment
of requested HEARTBEATS and timer HEARTBEATS is the same
wrt resetting congestion window. That needs to be separated,
since user requested HEARTBEATS should not treat the link
as idle.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The above functions from include/net/tcp.h have been defined with an
argument that they never use. The argument is 'u32 ack' which is never
used inside the function body, and thus it can be removed. The rest of
the patch involves the necessary changes to the function callers of the
above two functions.
Signed-off-by: Hantzis Fotis <xantzis@ceid.upatras.gr>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
fix warning in io_mapping_map_wc()
x86: i915 needs pgprot_writecombine() and is_io_mapping_possible()
Fix skbuff.h kernel-doc for timestamps: must include "struct" keyword,
otherwise there are kernel-doc errors:
Error(linux-next-20090227//include/linux/skbuff.h:161): cannot understand prototype: 'struct skb_shared_hwtstamps '
Error(linux-next-20090227//include/linux/skbuff.h:177): cannot understand prototype: 'union skb_shared_tx '
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the device to give the driver RX data with reorder information.
When that is done, the device will indicate the driver if a packet has
to be held in a (sorted) queue. It will also tell the driver when held
packets have to be released to the OS.
This is done to improve the WiMAX-protocol level retransmission
support when missing frames are detected.
The code docs provide details about the implementation.
In general, this just hooks into the RX path in rx.c; if a packet with
the reorder bit in the RX header is detected, the reorder information
in the header is extracted and one of the four main reorder operations
are executed. In one case (queue) no packet will be delivered to the
networking stack, just queued, whereas in the others (reset, update_ws
and queue_update_ws), queued packet might be delivered depending on
the window start for the specific queue.
The modifications to files other than rx.c are:
- control.c: during device initialization, enable reordering support
if the rx_reorder_disabled module parameter is not enabled
- driver.c: expose a rx_reorder_disable module parameter and call
i2400m_rx_setup/release() to initialize/shutdown RX reorder
support.
- i2400m.h: introduce members in 'struct i2400m' needed for
implementing reorder support.
- linux/i2400m.h: introduce TLVs, commands and constant definitions
related to RX reorder
Last but not least, the rx reorder code includes an small circular log
where the last N reorder operations are recorded to be displayed in
case of inconsistency. Otherwise diagnosing issues would be almost
impossible.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer i2400m firmwares (>= v1.4) extend the data RX protocol so that
each packet has a 16 byte header. This header is mainly used to
implement host reordeing (which is addressed in later commits).
However, this header also allows us to overwrite it (once data has
been extracted) with an Ethernet header and deliver to the networking
stack without having to reallocate the skb (as it happened in fw <=
v1.3) to make room for it.
- control.c: indicate the device [dev_initialize()] that the driver
wants to use the extended data RX protocol. Also involves adding the
definition of the needed data types in include/linux/wimax/i2400m.h.
- rx.c: handle the new payload type for the extended RX data
protocol. Prepares the skb for delivery to
netdev.c:i2400m_net_erx().
- netdev.c: Introduce i2400m_net_erx() that adds the fake ethernet
address to a prepared skb and delivers it to the networking
stack.
- cleanup: in most instances in rx.c, the variable 'single' was
renamed to 'single_last' for it better conveys its meaning.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For power saving reasons, WiMAX links can be put in idle mode while
connected after a certain time of the link not being used for tx or
rx. In this mode, the device pages the base-station regularly and when
data is ready to be transmitted, the link is revived.
This patch allows the user to control the time the device has to be
idle before it decides to go to idle mode from a sysfs
interace.
It also updates the initialization code to acknowledge the module
variable 'idle_mode_disabled' when the firmware is a newer version
(upcoming 1.4 vs 2.6.29's v1.3).
The method for setting the idle mode timeout in the older firmwares is
much more limited and can be only done at initialization time. Thus,
the sysfs file will return -ENOSYS on older ones.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also fixes insignificant bug that would cause sending of stale
SACK block (would occur in some corner cases).
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems that implementation in yeah was inconsistent to what
other did as it would increase cwnd one ack earlier than the
others do.
Size benefits:
bictcp_cong_avoid | -36
tcp_cong_avoid_ai | +52
bictcp_cong_avoid | -34
tcp_scalable_cong_avoid | -36
tcp_veno_cong_avoid | -12
tcp_yeah_cong_avoid | -38
= -104 bytes total
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DCB netlink interface is required for building the userspace tools
available at e1000.sourceforge.net
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) add an include for <linux/types.h>
2) change dcbmsg.dcb_family from unsigned char to __u8 to be more
consistent with use of kernel types
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some systems it is desirable for control for DAPM pins to be provided
to user space. This is the case with things like GSM modems which are
controlled primarily from user space, for example. Provide a helper which
exposes the state of a DAPM pin to user space for use in cases like this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: enable DMAR by default
xen: disable interrupts early, as start_kernel expects
gpu/drm, x86, PAT: io_mapping_create_wc and resource_size_t
gpu/drm, x86, PAT: Handle io_mapping_create_wc() errors in a clean way
x86, Voyager: fix compile by lifting the degeneracy of phys_cpu_present_map
x86, doc: fix references to Documentation/x86/i386/boot.txt
free_uid() and free_user_ns() are corecursive when CONFIG_USER_SCHED=n,
but free_user_ns() is called from free_uid() by way of uid_hash_remove(),
which requires uidhash_lock to be held. free_user_ns() then calls
free_uid() to complete the destruction.
Fix this by deferring the destruction of the user_namespace.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When devices are world roaming they cannot beacon or do active scan
on 5 GHz or on channels 12, 13 and 14 on the 2 GHz band. Although
we have a good regulatory API some cards may _always_ world roam, this
is also true when a system does not have CRDA present. Devices doing world
roaming can still passive scan, if they find a beacon from an AP on
one of the world roaming frequencies we make the assumption we can do
the same and we also remove the passive scan requirement.
This adds support for providing beacon regulatory hints based on scans.
This works for devices that do either hardware or software scanning.
If a channel has not yet been marked as having had a beacon present
on it we queue the beacon hint processing into the workqueue.
All wireless devices will benefit from beacon regulatory hints from
any wireless device on a system including new devices connected to
the system at a later time.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All regulatory hints (core, driver, userspace and 11d) are now processed in
a workqueue.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We do this so later on we can move the pending requests onto a
workqueue. By using the wiphy_idx instead of the wiphy we can
later easily check if the wiphy has disappeared or not.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds optional notifier functions for software scan.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The previous patch made cfg80211 generally aware of the signal
type a given hardware will give, so now it can implement
SIOCGIWRANGE itself, removing more wext stuff from mac80211.
Might need to be a little more parametrized once we have
more hardware using cfg80211 and new hardware capabilities.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It wasn't a good idea to make the signal type a per-BSS option,
although then it is closer to the actual value. Move it to be
a per-wiphy setting, update mac80211 to match.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TX/RX packet counters are needed to fill in RADIUS Accounting
attributes Acct-Output-Packets and Acct-Input-Packets. We already
collect the needed information, but only the TX/RX bytes were
previously exposed through nl80211. Allow applications to fetch the
packet counters, too, to provide more complete support for accounting.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This extends the NL80211_CMD_TRIGGER_SCAN command to allow applications
to specify a set of information element(s) to be added into Probe
Request frames with NL80211_ATTR_IE. This provides support for the
MLME-SCAN.request primitive parameter VendorSpecificInfo and can be
used, e.g., to implement WPS scanning.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The AP can switch dynamically between 20/40 Mhz channel width,
in which case we switch the local operating channel, but the
rate control algorithm is not notified. This patch adds a new callback
to indicate such changes to the RC algorithm.
Currently, HT channel width change is notified, but this callback
can be used to indicate any new requirements that might come up later on.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hardware with AMPDU queues currently has broken aggregation.
This patch fixes it by making all A-MPDUs go over the regular AC queues,
but keeping track of the hardware queues in mac80211. As a first rough
version, it actually stops the AC queue for extended periods of time,
which can be removed by adding buffering internal to mac80211, but is
currently not a huge problem because people rarely use multiple TIDs
that are in the same AC (and iwlwifi currently doesn't operate as AP).
This is a short-term fix, my current medium-term plan, which I hope to
execute soon as well, but am not sure can finish before .30, looks like
this:
1) rework the internal queuing layer in mac80211 that we use for
fragments if the driver stopped queue in the middle of a fragmented
frame to be able to queue more frames at once (rather than just a
single frame with its fragments)
2) instead of stopping the entire AC queue, queue up the frames in a
per-station/per-TID queue during aggregation session initiation,
when the session has come up take all those frames and put them
onto the queue from 1)
3) push the ampdu queue layer abstraction this patch introduces in
mac80211 into the driver, and remove the virtual queue stuff from
mac80211 again
This plan will probably also affect ath9k in that mac80211 queues the
frames instead of passing them down, even when there are no ampdu queues.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Only ipw2x00 now uses it. Reduce confusion. Profit!
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix ib_set_rmpp_flags() to use the correct bit mask for RRespTime. In
the 8-bit field of the RMPP header, the first 5 bits are RRespTime and
next 3 bits are RMPPFlags. Hence to retain the first 5 bits, the mask
should be 0xF8 instead of 0xF1.
ack_recv()-->format_ack() calls ib_set_rmpp_flags() and due to the
incorrect ANDing with 0xF1, RRespTime got changed incorrectly and RMPP
Acks sent back always had a RRespTime of 0x1E (30) which caused the
other end to consider the time outs to be approximately 4297 seconds
(i.e. in the order of 4*2^30) instead of the usual ~4 seconds (order
of 4*2^20).
Signed-off-by: Ramachandra K <ramachandra.kuchimanchi@qlogic.com>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Impact: fix hung task with certain (non-default) rt-limit settings
Corey Hickey reported that on using setuid to change the uid of a
rt process, the process would be unkillable and not be running.
This is because there was no rt runtime for that user group. Add
in a check to see if a user can attach an rt task to its task group.
On failure, return EINVAL, which is also returned in
CONFIG_CGROUP_SCHED.
Reported-by: Corey Hickey <bugfood-ml@fatooh.org>
Signed-off-by: Dhaval Giani <dhaval@linux.vnet.ibm.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Instead of keeping the single vector -> single linux irq mapping
we extend the intc code to support merging of vectors to a single
linux irq. This helps processors such as sh7750, sh7780 and sh7785
which have more vectors than masking ability. With this patch in
place we can modify the intc tables to use one irq per maskable
irq source. Please note the following:
- If multiple vectors share the same enum then only the
first vector will be available as a linux irq.
- Drivers may need to be rewritten to get pending irq
source from the hardware block instead of irq number.
This patch together with the sh7785 specific intc tables solves
DMA controller irq issues related to buggy interrupt masking.
Reported-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Applications include this header in order to use RDS sockets.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RDS is a reliable datagram protocol used for IPC on Oracle
database clusters. This adds address and protocol family numbers
for it.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: Attribute function with __releases(...)
Fix this sparse warning:
net/ipv4/inet_fragment.c:276:35: warning: context imbalance in 'inet_frag_find' - unexpected unlock
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the maple bus to support asynchronous block reads
and writes as well as generally improving the quality of the code and
supporting concurrency (all needed to support the Dreamcast visual
memory unit - a driver will also be posted for that).
Changes in the bus driver necessitate some changes in the two maple bus
input drivers that are currently in mainline.
As well as supporting block reads and writes this code clean up removes
some poor handling of locks, uses an atomic status variable to serialise
access to devices and more robusly handles the general performance
problems of the bus.
Signed-off-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Some of the qualification tests demand that in case of failures in L2CAP
the HCI disconnect should indicate a reason why L2CAP fails. This is a
bluntly layer violation since multiple L2CAP connections could be using
the same ACL and thus forcing a disconnect reason is not a good idea.
To comply with the Bluetooth test specification, the disconnect reason
is now stored in the L2CAP connection structure and every time a new
L2CAP channel is added it will set back to its default. So only in the
case where the L2CAP channel with the disconnect reason is really the
last one, it will propagated to the HCI layer.
The HCI layer has been extended with a disconnect indication that allows
it to ask upper layers for a disconnect reason. The upper layer must not
support this callback and in that case it will nicely default to the
existing behavior. If an upper layer like L2CAP can provide a disconnect
reason that one will be used to disconnect the ACL or SCO link.
No modification to the ACL disconnect timeout have been made. So in case
of Linux to Linux connection the initiator will disconnect the ACL link
before the acceptor side can signal the specific disconnect reason. That
is perfectly fine since Linux doesn't make use of this value anyway. The
L2CAP layer has a perfect valid error code for rejecting connection due
to a security violation. It is unclear why the Bluetooth specification
insists on having specific HCI disconnect reason.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In preparation for L2CAP fixed channel support, the CID value of a
L2CAP connection needs to be accessible via the socket interface. The
CID is the connection identifier and exists as source and destination
value. So extend the L2CAP socket address structure with this field and
change getsockname() and getpeername() to fill it in.
The bind() and connect() functions have been modified to handle L2CAP
socket address structures of variable sizes. This makes them future
proof if additional fields need to be added.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If the extended features mask indicates support for fixed channels,
request the list of available fixed channels. This also enables the
fixed channel features bit so remote implementations can request
information about it. Currently only the signal channel will be
listed.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The recommendation for the L2CAP PSM 1 (SDP) is to not use any kind
of authentication or encryption. So don't trigger authentication
for incoming and outgoing SDP connections.
For L2CAP PSM 3 (RFCOMM) there is no clear requirement, but with
Bluetooth 2.1 the initiator is required to enable authentication
and encryption first and this gets enforced. So there is no need
to trigger an additional authentication step. The RFCOMM service
security will make sure that a secure enough link key is present.
When the encryption gets enabled after the SDP connection setup,
then switch the security level from SDP to low security.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If the remote L2CAP server uses authentication pending stage and
encryption is enabled it can happen that a L2CAP connection request is
sent twice due to a race condition in the connection state machine.
When the remote side indicates any kind of connection pending, then
track this state and skip sending of L2CAP commands for this period.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When two L2CAP connections are requested quickly after the ACL link has
been established there exists a window for a race condition where a
connection request is sent before the information response has been
received. Any connection request should only be sent after an exchange
of the extended features mask has been finished.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When receiving incoming connection to specific services, always use
general bonding. This ensures that the link key gets stored and can be
used for further authentications.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When attempting to setup eSCO connections it can happen that some link
manager implementations fail to properly negotiate the eSCO parameters
and thus fail the eSCO setup. Normally the link manager is responsible
for the negotiation of the parameters and actually fallback to SCO if
no agreement can be reached. In cases where the link manager is just too
stupid, then at least try to establish a SCO link if eSCO fails.
For the Bluetooth devices with EDR support this includes handling packet
types of EDR basebands. This is particular tricky since for the EDR the
logic of enabling/disabling one specific packet type is turned around.
This fix contains an extra bitmask to disable eSCO EDR packet when
trying to fallback to a SCO connection.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
A role switch with devices following the Bluetooth pre-2.1 standards
or without Encryption Pause and Resume support is not possible if
encryption is enabled. Most newer headsets require the role switch,
but also require that the connection is encrypted.
For connections with a high security mode setting, the link will be
immediately dropped. When the connection uses medium security mode
setting, then a grace period is introduced where the TX is halted and
the remote device gets a change to re-enable encryption after the
role switch. If not re-enabled the link will be dropped.
Based on initial work by Ville Tervo <ville.tervo@nokia.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The current security model is based around the flags AUTH, ENCRYPT and
SECURE. Starting with support for the Bluetooth 2.1 specification this is
no longer sufficient. The different security levels are now defined as
SDP, LOW, MEDIUM and SECURE.
Previously it was possible to set each security independently, but this
actually doesn't make a lot of sense. For Bluetooth the encryption depends
on a previous successful authentication. Also you can only update your
existing link key if you successfully created at least one before. And of
course the update of link keys without having proper encryption in place
is a security issue.
The new security levels from the Bluetooth 2.1 specification are now
used internally. All old settings are mapped to the new values and this
way it ensures that old applications still work. The only limitation
is that it is no longer possible to set authentication without also
enabling encryption. No application should have done this anyway since
this is actually a security issue. Without encryption the integrity of
the authentication can't be guaranteed.
As default for a new L2CAP or RFCOMM connection, the LOW security level
is used. The only exception here are the service discovery sessions on
PSM 1 where SDP level is used. To have similar security strength as with
a Bluetooth 2.0 and before combination key, the MEDIUM level should be
used. This is according to the Bluetooth specification. The MEDIUM level
will not require any kind of man-in-the-middle (MITM) protection. Only
the HIGH security level will require this.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In order to decide if listening RFCOMM sockets should be accept()ed
the BD_ADDR of the remote device needs to be known. This patch adds
a socket option which defines a timeout for deferring the actual
connection setup.
The connection setup is done after reading from the socket for the
first time. Until then writing to the socket returns ENOTCONN.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The L2CAP and RFCOMM applications require support for authorization
and the ability of rejecting incoming connection requests. The socket
interface is not really able to support this.
This patch does the ground work for a socket option to defer connection
setup. Setting this option allows calling of accept() and then the
first read() will trigger the final connection setup. Calling close()
would reject the connection.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Allow CONFIG_HAVE_UNSTABLE_SCHED_CLOCK architectures to still specify
that their sched_clock() implementation is reliable.
This will be used by x86 to switch on a faster sched_clock_cpu()
implementation on certain CPU types.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch fixes a bug located by Vegard Nossum with the aid of
kmemcheck, updated based on review comments from Nick Piggin,
Ingo Molnar, and Andrew Morton. And cleans up the variable-name
and function-name language. ;-)
The boot CPU runs in the context of its idle thread during boot-up.
During this time, idle_cpu(0) will always return nonzero, which will
fool Classic and Hierarchical RCU into deciding that a large chunk of
the boot-up sequence is a big long quiescent state. This in turn causes
RCU to prematurely end grace periods during this time.
This patch changes the rcutree.c and rcuclassic.c rcu_check_callbacks()
function to ignore the idle task as a quiescent state until the
system has started up the scheduler in rest_init(), introducing a
new non-API function rcu_idle_now_means_idle() to inform RCU of this
transition. RCU maintains an internal rcu_idle_cpu_truthful variable
to track this state, which is then used by rcu_check_callback() to
determine if it should believe idle_cpu().
Because this patch has the effect of disallowing RCU grace periods
during long stretches of the boot-up sequence, this patch also introduces
Josh Triplett's UP-only optimization that makes synchronize_rcu() be a
no-op if num_online_cpus() returns 1. This allows boot-time code that
calls synchronize_rcu() to proceed normally. Note, however, that RCU
callbacks registered by call_rcu() will likely queue up until later in
the boot sequence. Although rcuclassic and rcutree can also use this
same optimization after boot completes, rcupreempt must restrict its
use of this optimization to the portion of the boot sequence before the
scheduler starts up, given that an rcupreempt RCU read-side critical
section may be preeempted.
In addition, this patch takes Nick Piggin's suggestion to make the
system_state global variable be __read_mostly.
Changes since v4:
o Changes the name of the introduced function and variable to
be less emotional. ;-)
Changes since v3:
o WARN_ON(nr_context_switches() > 0) to verify that RCU
switches out of boot-time mode before the first context
switch, as suggested by Nick Piggin.
Changes since v2:
o Created rcu_blocking_is_gp() internal-to-RCU API that
determines whether a call to synchronize_rcu() is itself
a grace period.
o The definition of rcu_blocking_is_gp() for rcuclassic and
rcutree checks to see if but a single CPU is online.
o The definition of rcu_blocking_is_gp() for rcupreempt
checks to see both if but a single CPU is online and if
the system is still in early boot.
This allows rcupreempt to again work correctly if running
on a single CPU after booting is complete.
o Added check to rcupreempt's synchronize_sched() for there
being but one online CPU.
Tested all three variants both SMP and !SMP, booted fine, passed a short
rcutorture test on both x86 and Power.
Located-by: Vegard Nossum <vegard.nossum@gmail.com>
Tested-by: Vegard Nossum <vegard.nossum@gmail.com>
Tested-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
During host driver module removal del_gendisk() results in a final
put on drive->gendev and freeing the drive by drive_release_dev().
Convert device drivers from using struct kref to use struct device
so device driver's object holds reference on ->gendev and prevents
drive from prematurely going away.
Also fix ->remove methods to not erroneously drop reference on a
host driver by using only put_device() instead of ide*_put().
Reported-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
io_mapping_create_wc should take a resource_size_t parameter in place of
unsigned long. With unsigned long, there will be no way to map greater than 4GB
address in i386/32 bit.
On x86, greater than 4GB addresses cannot be mapped on i386 without PAE. Return
error for such a case.
Patch also adds a structure for io_mapping, that saves the base, size and
type on HAVE_ATOMIC_IOMAP archs, that can be used to verify the offset on
io_mapping_map calls.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Eric Anholt <eric@anholt.net>
Cc: Keith Packard <keithp@keithp.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch changes the return value of nlmsg_notify() as follows:
If NETLINK_BROADCAST_ERROR is set by any of the listeners and
an error in the delivery happened, return the broadcast error;
else if there are no listeners apart from the socket that
requested a change with the echo flag, return the result of the
unicast notification. Thus, with this patch, the unicast
notification is handled in the same way of a broadcast listener
that has set the NETLINK_BROADCAST_ERROR socket flag.
This patch is useful in case that the caller of nlmsg_notify()
wants to know the result of the delivery of a netlink notification
(including the broadcast delivery) and take any action in case
that the delivery failed. For example, ctnetlink can drop packets
if the event delivery failed to provide reliable logging and
state-synchronization at the cost of dropping packets.
This patch also modifies the rtnetlink code to ignore the return
value of rtnl_notify() in all callers. The function rtnl_notify()
(before this patch) returned the error of the unicast notification
which makes rtnl_set_sk_err() reports errors to all listeners. This
is not of any help since the origin of the change (the socket that
requested the echoing) notices the ENOBUFS error if the notification
fails and should resync itself.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases we may receive a mode config that has a different
CRTC<->encoder map that the current configuration. In that case, we
need to disable any re-routed encoders before setting the mode,
otherwise they may not pick up the new CRTC (if the output types are
incompatible for example).
Tested-by: Kristian Høgsberg <krh@bitplanet.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>
The unit in which user-space can set the bus timeout value is jiffies
for historical reasons (back when HZ was always 100.) This is however
not good because user-space doesn't know how long a jiffy lasts. The
timeout value should instead be set in a fixed time unit. Given the
original value of HZ, this unit should be 10 ms, for compatibility.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
iptables imports headers from (the unifdefed headers of a)
kernel tree, but some headers happened to not be installed.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
netns: fix double free at netns creation
veth : add the set_mac_address capability
sunlance: Beyond ARRAY_SIZE of ib->btx_ring
sungem: another error printed one too early
ISDN: fix sc/shmem printk format warning
SMSC: timeout reaches -1
smsc9420: handle magic field of ethtool_eeprom
sundance: missing parentheses?
smsc9420: fix another postfixed timeout
wimax/i2400m: driver loads firmware v1.4 instead of v1.3
vlan: Update skb->mac_header in __vlan_put_tag().
cxgb3: Add support for PCI ID 0x35.
tcp: remove obsoleted comment about different passes
TG3: &&/|| confusion
ATM: misplaced parentheses?
net/mv643xx: don't disable the mib timer too early and lock properly
net/mv643xx: use GFP_ATOMIC while atomic
atl1c: Atheros L1C Gigabit Ethernet driver
net: Kill skb_truesize_check(), it only catches false-positives.
net: forcedeth: Fix wake-on-lan regression
Although it allows for better cacheline use, it is unnecessary to save a
copy of the cache's min_partial value in each kmem_cache_node.
Cc: Christoph Lameter <cl@linux-foundation.org>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
It turns out that net_alive is unnecessary, and the original problem
that led to it being added was simply that the icmp code thought
it was a network device and wound up being unable to handle packets
while there were still packets in the network namespace.
Now that icmp and tcp have been fixed to properly register themselves
this problem is no longer present and we have a stronger guarantee
that packets will not arrive in a network namespace then that provided
by net_alive in netif_receive_skb. So remove net_alive allowing
packet reception run a little faster.
Additionally document the strong reason why network namespace cleanup
is safe so that if something happens again someone else will have
a chance of figuring it out.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the sysdev_suspend/resume from the callee to the callers, with
no real change in semantics, so that we can rework the disabling of
interrupts during suspend/hibernation.
This is based on an earlier patch from Linus.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some hardware platforms, the TS-7800[1] is one for example, can
supply the kernel with an entropy source, albeit a slow one for
TS-7800 users, by just reading a particular IO address. This
source must not be read above a certain rate otherwise the quality
suffers.
The driver is then hooked into by calling
platform_device_(register|add|del) passing a structure similar to:
------
static struct timeriomem_rng_data ts78xx_ts_rng_data = {
.address = (u32 *__iomem) TS_RNG,
.period = 1000000, /* one second */
};
static struct platform_device ts78xx_ts_rng_device = {
.name = "timeriomem_rng",
.id = -1,
.dev = {
.platform_data = &ts78xx_ts_rng_data,
},
.num_resources = 0,
};
------
[1] http://www.embeddedarm.com/products/board-detail.php?product=TS-7800
Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
* hibernate:
PM: Fix suspend_console and resume_console to use only one semaphore
PM: Wait for console in resume
PM: Fix pm_notifiers during user mode hibernation
swsusp: clean up shrink_all_zones()
swsusp: dont fiddle with swappiness
PM: fix build for CONFIG_PM unset
PM/hibernate: fix "swap breaks after hibernation failures"
PM/resume: wait for device probing to finish
Consolidate driver_probe_done() loops into one place
there's a few places that currently loop over driver_probe_done(), and
I'm about to add another one. This patch abstracts it into a helper
to reduce duplication.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Len Brown <lenb@kernel.org>
Acked-by: Greg KH <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (26 commits)
drm/radeon: update sarea copies of last_ variables on resume.
drm/i915: Keep refs on the object over the lifetime of vmas for GTT mmap.
drm/i915: take struct mutex around fb unref
drm: Use spread spectrum when the bios tells us it's ok.
drm: Collapse identical i8xx_clock() and i9xx_clock().
drm: Bring PLL limits in sync with DDX values.
drm: Add locking around cursor gem operations.
drm: Propagate failure from setting crtc base.
drm: Check for a NULL encoder when reverting on error path
drm/i915: Cleanup the hws on ringbuffer constrution failure.
drm/i915: Don't add panel_fixed_mode to the probed modes list at LVDS init.
drm: Release user fbs in drm_release
drm/i915: Unpin the fb on error during construction.
drm/i915: Unpin the hws if we fail to kmap.
drm/i915: Unpin the ringbuffer if we fail to ioremap it.
drm/i915: unpin for an invalid memory domain.
drm/i915: Release and unlock on mmap_gtt error path.
drm/i915: Set framebuffer alignment based upon the fence constraints.
drm: Do not leak a new reference for flink() on an existing name
drm/i915: Fix potential AB-BA deadlock in i915_gem_execbuffer()
...
Intel 8257x Ethernet boards have a feature called Serial Over Lan.
This feature works by emulating a serial port, and it is detected by
kernel as a normal 8250 port. However, this emulation is not perfect, as
also noticed on changeset 7500b1f602.
Before this patch, the kernel were trying to check if the serial TX is
capable of work using IRQ's.
This were done with a code similar this:
serial_outp(up, UART_IER, UART_IER_THRI);
lsr = serial_in(up, UART_LSR);
iir = serial_in(up, UART_IIR);
serial_outp(up, UART_IER, 0);
if (lsr & UART_LSR_TEMT && iir & UART_IIR_NO_INT)
up->bugs |= UART_BUG_TXEN;
This works fine for other 8250 ports, but, on 8250-emulated SoL port, the
chip is a little lazy to down UART_IIR_NO_INT at UART_IIR register.
Due to that, UART_BUG_TXEN is sometimes enabled. However, as TX IRQ keeps
working, and the TX polling is now enabled, the driver miss-interprets the
IRQ received later, hanging up the machine until a key is pressed at the
serial console.
This is the 6 version of this patch. Previous versions were trying to
introduce a large enough delay between serial_outp and serial_in(up,
UART_IIR), but not taking forever. However, the needed delay couldn't be
safely determined.
At the experimental tests, a delay of 1us solves most of the cases, but
still hangs sometimes. Increasing the delay to 5us was better, but still
doesn't solve. A very high delay of 50 ms seemed to work every time.
However, poking around with delays and pray for it to be enough doesn't
seem to be a good approach, even for a quirk.
So, instead of playing with random large arbitrary delays, let's just
disable UART_BUG_TXEN for all SoL ports.
[akpm@linux-foundation.org: fix warnings]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds more documentation of the lowlevel API to avoid future bugs.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
kzfree() is a wrapper for kfree() that additionally zeroes the underlying
memory before releasing it to the slab allocator.
Currently there is code which memset()s the memory region of an object
before releasing it back to the slab allocator to make sure
security-sensitive data are really zeroed out after use.
These callsites can then just use kzfree() which saves some code, makes
users greppable and allows for a stupid destructor that isn't necessarily
aware of the actual object size.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Matt Mackall <mpm@selenic.com>
Acked-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Increase the maximum object size in SLUB so that 8k objects are not
passed through to the page allocator anymore. The network stack uses 8k
objects for performance critical operations.
The patch is motivated by a SLAB vs. SLUB regression in the netperf
benchmark. The problem is that the kfree(skb->head) call in
skb_release_data() that is subject to page allocator pass-through as the
size passed to __alloc_skb() is larger than 4 KB in this test.
As explained by Yanmin Zhang:
I use 2.6.29-rc2 kernel to run netperf UDP-U-4k CPU_NUM client/server
pair loopback testing on x86-64 machines. Comparing with SLUB, SLAB's
result is about 2.3 times of SLUB's. After applying the reverting patch,
the result difference between SLUB and SLAB becomes 1% which we might
consider as fluctuation.
[ penberg@cs.helsinki.fi: fix oops in kmalloc() ]
Reported-by: "Zhang, Yanmin" <yanmin_zhang@linux.intel.com>
Tested-by: "Zhang, Yanmin" <yanmin_zhang@linux.intel.com>
Signed-off-by: Christoph Lameter <cl@linux-foundation.org>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
As a preparational patch to bump up page allocator pass-through threshold,
introduce two new constants SLUB_MAX_SIZE and SLUB_PAGE_SHIFT and convert
mm/slub.c to use them.
Reported-by: "Zhang, Yanmin" <yanmin_zhang@linux.intel.com>
Tested-by: "Zhang, Yanmin" <yanmin_zhang@linux.intel.com>
Signed-off-by: Christoph Lameter <cl@linux-foundation.org>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Kernel module providing implementation of LED netfilter target. Each
instance of the target appears as a led-trigger device, which can be
associated with one or more LEDs in /sys/class/leds/
Signed-off-by: Adam Nielsen <a.nielsen@shikadi.net>
Acked-by: Richard Purdie <rpurdie@linux.intel.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Table size is defined as unsigned, wheres the table maximum size is
defined as a signed integer. The calculation of max is 8 or 4,
multiplied the table size. Therefore the max value is aligned to
unsigned.
Signed-off-by: Hagen Paul Pfeifer <hagen@jauu.net>
Signed-off-by: Patrick McHardy <kaber@trash.net>
The reader/writer lock in ip_tables is acquired in the critical path of
processing packets and is one of the reasons just loading iptables can cause
a 20% performance loss. The rwlock serves two functions:
1) it prevents changes to table state (xt_replace) while table is in use.
This is now handled by doing rcu on the xt_table. When table is
replaced, the new table(s) are put in and the old one table(s) are freed
after RCU period.
2) it provides synchronization when accesing the counter values.
This is now handled by swapping in new table_info entries for each cpu
then summing the old values, and putting the result back onto one
cpu. On a busy system it may cause sampling to occur at different
times on each cpu, but no packet/byte counts are lost in the process.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Sucessfully tested on my dual quad core machine too, but iptables only (no ipv6 here)
BTW, my new "tbench 8" result is 2450 MB/s, (it was 2150 MB/s not so long ago)
Acked-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch adds NETLINK_BROADCAST_ERROR which is a netlink
socket option that the listener can set to make netlink_broadcast()
return errors in the delivery to the caller. This option is useful
if the caller of netlink_broadcast() do something with the result
of the message delivery, like in ctnetlink where it drops a network
packet if the event delivery failed, this is used to enable reliable
logging and state-synchronization. If this socket option is not set,
netlink_broadcast() only reports ESRCH errors and silently ignore
ENOBUFS errors, which is what most netlink_broadcast() callers
should do.
This socket option is based on a suggestion from Patrick McHardy.
Patrick McHardy can exchange this patch for a beer from me ;).
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes potential fault at fault time if the object was unreferenced
while the mapping still existed. Now, while the mmap_offset only lives
for the lifetime of the object, the object also stays alive while a vma
exists that needs it.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Check the error paths within intel_pipe_set_base() to first cleanup and
then report back the error.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Avoids leaking fbs and associated buffers on release.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Tested-by: Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
After moving mac addresses in __vlan_put_tag() skb->mac_header needs
to be updated.
Reported-by: Karl Hiramoto <karl@hiramoto.org>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use dedicated workqueue for crypto subsystem
A dedicated workqueue named kcrypto_wq is created to be used by crypto
subsystem. The system shared keventd_wq is not suitable for
encryption/decryption, because of potential starvation problem.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Maciej Sosnowski