Channel disabling/halting should performed for enabled only channels
to avoid warnings "Unable to clear enable on channel N" which seen
if host works in Slave mode.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
On ISOC transfer completion, in DDMA mode, set actual frame
number returning to function driver in usb_request.
Due to core limitation, returning frame number is 11-bit wide.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Some function drivers queueing more than 128 ISOC requests at a time.
To avoid "descriptor chain full" cases, increasing descriptors count
from MAX_DMA_DESC_NUM_GENERIC to MAX_DMA_DESC_NUM_HS_ISOC for ISOC's
only.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added delayed status support for Control transfers.
Tested in all 3 modes: Slave, BDMA and DDMA.
Performed tests: USB CV (Ch9 and MSC), Control Read/Write tests
using Synopsys USB test environment function driver.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Most of the phy initialization is shared between host and gadget,
this adds the turnaround configuration only used by gadgets to
the global phy init.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Jules Maselbas <jmaselbas@kalray.eu>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
As the phy initialization is almost the same in host and gadget
mode. This only move the phy initialization functions into core.c
for now, the goal is to share theses functions between the two modes.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Jules Maselbas <jmaselbas@kalray.eu>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The phy utmi width information is already set in hsotg params,
phyif is only used in few places and I don't see any reason to
not use hsotg's params.
Moreover the utmi width was being forced to 16 bits by platform
initialization which doesn't take in account HW configuration.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Jules Maselbas <jmaselbas@kalray.eu>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The function dwc2_hsotg_init is only called once just before calling
dwc2_hsotg_core_init_disconnected which does the same initialization:
setting the usbcfg register with turnaround time, timeout calibration
and phy width.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Jules Maselbas <jmaselbas@kalray.eu>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Makes GHWCFG4_UTMI_PHY_DATA* defines closer to their relative shift and
mask defines to improve readability.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Jules Maselbas <jmaselbas@kalray.eu>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
On the rk3288 USB host-only port (the one that's not the OTG-enabled
port) the PHY can get into a bad state when a wakeup is asserted (not
just a wakeup from full system suspend but also a wakeup from
autosuspend).
We can get the PHY out of its bad state by asserting its "port reset",
but unfortunately that seems to assert a reset onto the USB bus so it
could confuse things if we don't actually deenumerate / reenumerate the
device.
We can also get the PHY out of its bad state by fully resetting it using
the reset from the CRU (clock reset unit), which does a more full
reset. The CRU-based reset appears to actually cause devices on the bus
to be removed and reinserted, which fixes the problem (albeit in a hacky
way).
It's unfortunate that we need to do a full re-enumeration of devices at
wakeup time, but this is better than alternative of letting the bus get
wedged.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Yunzhi Li <lyz@rock-chips.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When the driver tries to get optional clock, it ignores all errors,
but if only ignores -ENOENT, it will cover some real errors, such as
-EPROBE_DEFER, so use devm_clk_get_optional() to get optional clock.
Cc: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Avoiding switch to L1 state in any stage of control transfers.
Send NYET handshake to LPM token.
Renamed GLPMCFG_LPM_ACCEPT_CTRL_ISOC to GLPMCFG_LPM_REJECT_CTRL_CONTROL
because by setting this bit core reject LPM token.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This is an attempt to rehash commit 0cf884e819 ("usb: dwc2: add bus
suspend/resume for dwc2") on ToT. That commit was reverted in commit
b0bb9bb6ce ("Revert "usb: dwc2: add bus suspend/resume for dwc2"")
because apparently it broke the Altera SOCFPGA.
With all the changes that have happened to dwc2 in the meantime, it's
possible that the Altera SOCFPGA will just magically work with this
change now. ...and it would be good to get bus suspend/resume
implemented.
This change is a forward port of one that's been living in the Chrome
OS 3.14 kernel tree.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patchs sets the params for the DWC2 Controller found in the
Amlogic G12A SoC family.
It mainly sets the settings reported incorrect by the driver,
leaving the remaining detected automatically by the driver and
provided by the DT node.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
struct boo entry[];
};
size = sizeof(struct foo) + count * sizeof(struct boo);
instance = kzalloc(size, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);
Notice that, in this case, variable size is not necessary, hence
it is removed.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dwc3 now works on TI's AM6xx platforms. Also on dwc3 we have a few
changes which improve request cancellation and some improvements to
how we print to the trace buffer.
Renesas_usb3 got support for r8a774c0 device.
Dwc2 got scatter-gather support.
Apart from these, the usual set of minor fixes and all sorts of small
details.
-----BEGIN PGP SIGNATURE-----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=4fTL
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
USB: changes for v5.1 merge window
Dwc3 now works on TI's AM6xx platforms. Also on dwc3 we have a few
changes which improve request cancellation and some improvements to
how we print to the trace buffer.
Renesas_usb3 got support for r8a774c0 device.
Dwc2 got scatter-gather support.
Apart from these, the usual set of minor fixes and all sorts of small
details.
* tag 'usb-for-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (40 commits)
usb: phy: twl6030-usb: fix possible use-after-free on remove
usb: misc: usbtest: add super-speed isoc support
usb: dwc3: Reset num_trbs after skipping
usb: dwc3: gadget: don't enable interrupt when disabling endpoint
fotg210-udc: pass struct device to DMA API functions
fotg210-udc: remove a bogus dma_sync_single_for_device call
usb: gadget: Change Andrzej Pietrasiewicz's e-mail address
usb: f_fs: Avoid crash due to out-of-scope stack ptr access
usb: dwc3: haps: Workaround matching VID PID
usb: gadget: f_fs: preserve wMaxPacketSize across usb_ep_autoconfig() call
usb: gadget: move non-super speed code out of usb_ep_autoconfig_ss()
usb: gadget: function: sync f_uac1 ac header baInterfaceNr
usb: dwc2: gadget: Add scatter-gather mode
usb: gadget: fix various indentation issues
usb: dwc2: Fix EP TxFIFO number setting
udc: net2280: Fix net2280_disable
USB: gadget: Improve kerneldoc for usb_ep_dequeue()
usb: dwc3: debug: purge usage of strcat
usb: dwc3: trace: pass trace buffer size to decoding functions
usb: dwc3: gadget: remove DWC3_EP_END_TRANSFER_PENDING
...
This patch adds support for transferring requests, which are
non-contiguous in physical memory, i.e. the data buffer is described by
a scatter-list. This allows transferring large requests without relying
on error-prone contiguous buffer allocations. This way of allocating
requests is already implemented in functionfs and TCM USB functions and
automatically used if UDC driver advertises scatter-gather suppport.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
[mszyprow: fixed null pointer issue, rewrote commit message]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case when some EP IN is frequently reused, i.e. enabled/disabled by
function driver. It is required to clear TxFIFO number field in DIEPCTL
register before setting new number. Otherwise there is probability to
have same TxFIFO number for different EP's because of OR operator.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There are a few remaining drivers/usb/ files that do not have SPDX
identifiers in them, all of these are either Kconfig or Makefiles. Add
the correct GPL-2.0 identifier to them to make scanning tools happy.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To clear GINTSTS2_WKUP_ALERT_INT bit in GINTSTS2 register
require to write 1. This bit is implemented as "Write to clear".
Fixes: 187c5298a1 ("usb: dwc2: gadget: Add handler for WkupAlert interrupt")
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Disabling all EP's allow to reset EP's to initial state.
Introduced new function dwc2_hsotg_ep_disable_lock() which
before calling dwc2_hsotg_ep_disable() function acquire
hsotg->lock and release on exiting.
From dwc2_hsotg_ep_disable() function removed acquiring
hsotg->lock.
In dwc2_hsotg_core_init_disconnected() function when USB
reset interrupt asserted disabling all ep’s by
dwc2_hsotg_ep_disable() function.
This updates eliminating sparse imbalance warnings.
Reverted changes in dwc2_hostg_disconnect() function.
Introduced new function dwc2_hsotg_ep_disable_lock().
Changed dwc2_hsotg_ep_ops. Now disable point to
dwc2_hsotg_ep_disable_lock() function.
In functions dwc2_hsotg_udc_stop() and dwc2_hsotg_suspend()
dwc2_hsotg_ep_disable() function replaced by
dwc2_hsotg_ep_disable_lock() function.
In dwc2_hsotg_ep_disable() function removed acquiring
of hsotg->lock.
Fixes: dccf1bad4b ("usb: dwc2: Disable all EP's on disconnect")
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Disable power_down by setting the parameter to
DWC2_POWER_DOWN_PARAM_NONE. This fixes a problem on various Amlogic
Meson SoCs where USB devices are only recognized when plugged in before
booting Linux. A hot-plugged USB device was not detected even though the
device got power (my USB thumb drive for example has an LED which lit
up).
A similar fix was implemented for Rockchip SoCs in commit c216765d3a
("usb: dwc2: disable power_down on rockchip devices"). That commit
suggests that a change in the dwc2 driver is the cause because the
default value for the "hibernate" parameter (which then got renamed to
"power_down" to support other modes) was changed in the v4.17 merge
window with:
commit 6d23ee9caa ("Merge tag 'usb-for-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-testing").
Cc: <stable@vger.kernel.org> # 4.19
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Suggested-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Modify the wait delay utilize the high resolution timer API to allow for
more precisely scheduled callbacks.
A previous commit added a 1ms retry delay after multiple consecutive
NAKed transactions using jiffies. On systems with a low timer interrupt
frequency, this delay may be significantly longer than specified,
resulting in misbehavior with some USB devices.
This scenario was reached on a Raspberry Pi 3B with a Macally FDD-USB
floppy drive (identified as 0424:0fdc Standard Microsystems Corp.
Floppy, based on the USB97CFDC USB FDC). With the relay delay, the drive
would be unable to mount a disk, replying with NAKs until the device was
reset.
Using ktime, the delta between starting the timer (in dwc2_hcd_qh_add)
and the callback function can be determined. With the original delay
implementation, this value was consistently approximately 12ms. (output
in us).
<idle>-0 [000] ..s. 1600.559974: dwc2_wait_timer_fn: wait_timer delta: 11976
<idle>-0 [000] ..s. 1600.571974: dwc2_wait_timer_fn: wait_timer delta: 11977
<idle>-0 [000] ..s. 1600.583974: dwc2_wait_timer_fn: wait_timer delta: 11976
<idle>-0 [000] ..s. 1600.595974: dwc2_wait_timer_fn: wait_timer delta: 11977
After converting the relay delay to using a higher resolution timer, the
delay was much closer to 1ms.
<idle>-0 [000] d.h. 1956.553017: dwc2_wait_timer_fn: wait_timer delta: 1002
<idle>-0 [000] d.h. 1956.554114: dwc2_wait_timer_fn: wait_timer delta: 1002
<idle>-0 [000] d.h. 1957.542660: dwc2_wait_timer_fn: wait_timer delta: 1004
<idle>-0 [000] d.h. 1957.543701: dwc2_wait_timer_fn: wait_timer delta: 1002
The floppy drive operates properly with delays up to approximately 5ms,
and sends NAKs for any delays that are longer.
Fixes: 38d2b5fb75 ("usb: dwc2: host: Don't retry NAKed transactions right away")
Cc: <stable@vger.kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Terin Stock <terin@terinstock.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Power down feature of DWC2 module integrated in Samsung SoCs doesn't work
properly or needs some additional handling in PHY or SoC glue layer, so
disable it for now. Without disabling power down, DWC2 causes random memory
trashes and fails enumeration if there is no USB link to host on driver
probe.
Fixes: 03ea6d6e9e ("usb: dwc2: Enable power down")
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Set GLPMCFG_LPM_ACCEPT_CTRL_ISOC bit in GLPMCFG register
to accept LPM token during ISOC transfers when TxFIFO is
not empty.
- Added two definitions.
#define GLPMCFG_LPM_ACCEPT_CTRL_CONTROL BIT(21)
#define GLPMCFG_LPM_ACCEPT_CTRL_ISOC BIT(22)
This patch uses GLPMCFG_LPM_ACCEPT_CTRL_ISOC.
GLPMCFG_LPM_ACCEPT_CTRL_CONTROL is defined for further use.
- Added setting GLPMCFG_LPM_ACCEPT_CTRL_ISOC bit in GLPMCFG
register in dwc2_gadget_init_lpm function.
Signed-off-by: Artur Petrosyan <arturp@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
According to the databook DCTL_RMTWKUPSIG bit
is defined in DCTL register not in DCFG.
Updated setting DCTL_RMTWKUPSIG bit to DCTL
register.
Fixes: 187c5298a1 ("usb: dwc2: gadget: Add handler for WkupAlert interrupt")
Signed-off-by: Artur Petrosyan <arturp@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We added some error handling to this function but forgot to set the
error code on this path.
Fixes: ecd29dabb2 ("usb: dwc2: pci: Handle error cleanup in probe")
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The bug would let the usb controller enter partial power down,
which was formally known as hibernate, upon boot if nothing was plugged
in to the port. Partial power down couldn't be exited properly, so any
usb devices plugged in after boot would not be usable.
Before the name change, params.hibernation was false by default, so
_dwc2_hcd_suspend() would skip entering hibernation. With the
rename, _dwc2_hcd_suspend() was changed to use params.power_down
to decide whether or not to enter partial power down.
Since params.power_down is non-zero by default, it needs to be set
to 0 for rockchip devices to restore functionality.
This bug was reported in the linux-usb thread:
REGRESSION: usb: dwc2: USB device not seen after boot
The commit that caused this regression is:
6d23ee9caa
Signed-off-by: SolidHal <hal@halemmerich.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added interrupt handler for WkupAlert interrupt.
This interrupt should initiate Remote Wake up.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
WKUP_ALERT interrupt should be unmask when lpm mode is enabled.
This interrupt is asserted when the device is in L1 for the duration
mentioned in GREFCLK.SOF_CNN_WKUP_ALERT. This is used to alert SW to
initiate Remote wake up so that the device resumes in time in order not
to lose sync with the host frame number.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added dwc2_gadget_program_ref_clk function to program GREFCLK
register in device mode.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added ref_clk_per and sof_cnt_wkup_alert parameters in
dwc2_core_params struct and set default values.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
New registers were added to dwc otg core.
GREFCLK - This register used to control ref_clk parameters.
GINTSTS2 - New WKUP_ALERT interrupt was added.
GINTMSK2 - Mask register for GINTSTS2.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In service interval based scheduling target (u)frame must be
set as a last frame in this the service interval.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added dwc2_gadget_dec_frame_num_by_one() function in gadget.c.
This function will be used to calculate descriptor frame number field
value. For service interval mode frame number in descriptor should point
to last (u)frame in the interval.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added core parameter for service interval based scheduling.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added GHWCFG4_SERVICE_INTERVAL_SUPPORTED and
DCTL_SERVICE_INTERVAL_SUPPORTED bits definitions to support
service interval based scheduling.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When using external vbus supply regulator, it should be enabled
synchronously with PWR bit in HPRT register. This also fixes
unbalanced use of this optional regulator (This can be reproduced
easily when unbinding the driver).
Fixes: 531ef5ebea ("usb: dwc2: add support for host mode external
vbus supply")
Tested-by: Artur Petrosyan <arturp@synopsys.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc2_vbus_supply_exit() may call regulator_disable(). It shouldn't be
called with interrupts disabled as it might sleep.
This is seen with DEBUG_ATOMIC_SLEEP=y.
Fixes: 531ef5ebea ("usb: dwc2: add support for host mode external
vbus supply")
Tested-by: Artur Petrosyan <arturp@synopsys.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There's a race with root hub resume, when using external vbus supply.
Root hub gets resumed, but runtime pm autosuspend runs as external vbus
supply isn't enabled. So, host never exit from power down properly.
Initialize vbus external supply before, rater that after hub resume.
Fixes: 531ef5ebea ("usb: dwc2: add support for host mode external
vbus supply")
Tested-by: Artur Petrosyan <arturp@synopsys.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Move devm_regulator_get_optional() call to probe routine. This avoids
'vbus-supply' regulator to be requested lots of times, upon each call
to dwc2_vbus_supply_init(), e.g. like with runtime pm.
Fixes: 531ef5ebea ("usb: dwc2: add support for host mode external
vbus supply")
Tested-by: Artur Petrosyan <arturp@synopsys.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Disabling all EP's allow to reset EP's to initial state.
On disconnect disable all EP's instead of just killing
all requests. Because of some platform didn't catch
disconnect event, same stuff added to
dwc2_hsotg_core_init_disconnected() function when USB
reset detected on the bus.
Changed from version 1:
Changed lock acquire flow in dwc2_hsotg_ep_disable()
function.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch removes a set but unused variable in hcd.c.
Fixes gcc warning:
variable ‘data_fifo’ set but not used [-Wunused-but-set-variable]
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Joshua Abraham <j.abraham1776@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Some SoC/IP as STM32F469, the snpsid can only be read after clock is
enabled, otherwise it will read as 0, and the dwc2_check_core_endianness
will assume the core and AHB have opposite endianness, leading to the
following error:
[ 1.976339] dwc2 50000000.usb: 50000000.usb supply vusb_d not found, using dummy regulator
[ 1.986124] dwc2 50000000.usb: Linked as a consumer to regulator.0
[ 1.992711] dwc2 50000000.usb: 50000000.usb supply vusb_a not found, using dummy regulator
[ 2.003672] dwc2 50000000.usb: dwc2_core_reset: HANG! AHB Idle timeout GRSTCTL GRSTCTL_AHBIDLE
[ 2.015176] dwc2: probe of 50000000.usb failed with error -16
The proposed patch changes the location where dwc2_check_core_endianness
is called, allowing the clock peripheral to be enabled first.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Bruno Meirelles Herrera <bmh@certi.org.br>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Not a big pull request with only 37 non-merge commits, most of which
are touching dwc2 (74% of the changes).
The most important changes are dwc2's support for uframe scheduling
and its endian-agnostic readl/writel wrappers.
From dwc3 side we have a special new glue layer for Synopsys HAPS
which will help Synopsys running FPGA validation using our upstream
driver. We also have the beginnings of dual-role support for Intel
Merrifield platform.
Apart from these, just a series of non-critical changes.
-----BEGIN PGP SIGNATURE-----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=HiNz
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: changes for v4.19
Not a big pull request with only 37 non-merge commits, most of which
are touching dwc2 (74% of the changes).
The most important changes are dwc2's support for uframe scheduling
and its endian-agnostic readl/writel wrappers.
From dwc3 side we have a special new glue layer for Synopsys HAPS
which will help Synopsys running FPGA validation using our upstream
driver. We also have the beginnings of dual-role support for Intel
Merrifield platform.
Apart from these, just a series of non-critical changes.
There's no reason to have the uframe scheduler off on dwc2. Running
with uframe_sched = False is equivalent to saying "I don't want to run
the correct code, I want to run the old and incorrect code".
The uframe scheduler has been off on stm32f4x9_fsotg since commit
e35b135055 ("usb: dwc2: Add support for STM32F429/439/469 USB OTG
HS/FS in FS mode (internal PHY)"). That commit is pretty recent, so
it's unclear to me why the uframe scheduler was left off. Hopefully
it's because someone copied it from other parameters and didn't think
to try it?
Presumably if everyone is good w/ the uframe_sched turned back on we
can kill all the old and crufty non-uframe sched code.
Reviewed-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There's no reason to have the uframe scheduler off on dwc2. Running
with uframe_sched = False is equivalent to saying "I don't want to run
the correct code, I want to run the old and incorrect code".
The uframe scheduler has been off on Amlogic since commit f94310ac07
("usb: dwc2: add support for Meson8b and GXBB SoCs"). While this was
after most of the recent improvements, notably the commit 9f9f09b048
("usb: dwc2: host: Totally redo the microframe scheduler"), presumably
the parameters were copied from another platform and the uframe
scheduler wasn't tried.
Presumably if everyone is good w/ the uframe_sched turned back on we
can kill all the old and crufty non-uframe sched code.
Reviewed-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There's no reason to have the uframe scheduler off on dwc2. Running
with uframe_sched = False is equivalent to saying "I don't want to run
the correct code, I want to run the old and incorrect code".
The uframe scheduler has been off on HiSilicon since commit
37dd9d65cc ("usb: dwc2: add support of hi6220"). Since then there
have been many many improvements, notably the commit 9f9f09b048
("usb: dwc2: host: Totally redo the microframe scheduler")
Presumably if everyone is good w/ the uframe_sched turned back on we
can kill all the old and crufty non-uframe sched code.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Reviewed-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There's no reason to have the uframe scheduler off on dwc2. Running
with uframe_sched = False is equivalent to saying "I don't want to run
the correct code, I want to run the old and incorrect code".
The uframe scheduler has been off on Broadcom since commit
58b179dcf2 ("staging: dwc2: disable uframe_sched on the bcm2835").
Since then there have been many many improvements, notably the commit
9f9f09b048 ("usb: dwc2: host: Totally redo the microframe
scheduler")
Presumably if everyone is good w/ the uframe_sched turned back on we
can kill all the old and crufty non-uframe sched code.
Reviewed-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
To start ISOC transfers in handlers dwc2_gadget_handle_nak() and
dwc2_gadget_handle_out_token_ep_disabled() driver reads current frame
number, based on which, set target frame number to start first ISOC
transfer.
In case if system's high IRQ latency and multiple EP's asserted
interrupt in same frame, there are high probability that when reading
current frame number in EP's handlers, actual frame number can be
increased. As result for bInterval > 1, starting target frame
will be set wrongly and all ISOC packets will be dropped.
In patch "usb: dwc2: Change reading of current frame number flow"
reading of current frame number done ASAP in common interrupt handler.
This frame number stored in frame_number variable which used as
starting frame number for ISOC EP's in above mentioned handlers.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Declared dwc2_check_core_endianness() function for dynamicly check
core endianness.
Added needs_byte_swap flag to hsotg structure, and depending on
flag swap value inside dwc2_readl/writel functions.
Signed-off-by: Gevorg Sahakyan <sahakyan@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc2_readl_rep/dwc2_writel_rep functions using readl/writel in a
loop.
Signed-off-by: Gevorg Sahakyan <sahakyan@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added hsotg argument to dwc2_readl/writel function prototype,
and also instead of address pass offset of register.
hsotg will contain flag field for endianness.
Also customized dwc2_set_bit and dwc2_clear_bit function for
dwc2_readl/writel functions.
Signed-off-by: Gevorg Sahakyan <sahakyan@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Moved dwc2_readl/writel functions after hsotg declaration for
adding hsotg structure to dwc2_readl/writel function prototypes.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Gevorg Sahakyan <sahakyan@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Make sure only to copy any actual data rather than the whole buffer,
when releasing the temporary buffer used for unaligned non-isochronous
transfers.
Taken directly from commit 0efd937e27 ("USB: ehci-tegra: fix inefficient
copy of unaligned buffers")
Tested with Lantiq xRX200 (MIPS) and RPi Model B Rev 2 (ARM)
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The commit 3bc04e28a0 ("usb: dwc2: host: Get aligned DMA in a more
supported way") introduced a common way to align DMA allocations.
The code in the commit aligns the struct dma_aligned_buffer but the
actual DMA address pointed by data[0] gets aligned to an offset from
the allocated boundary by the kmalloc_ptr and the old_xfer_buffer
pointers.
This is against the recommendation in Documentation/DMA-API.txt which
states:
Therefore, it is recommended that driver writers who don't take
special care to determine the cache line size at run time only map
virtual regions that begin and end on page boundaries (which are
guaranteed also to be cache line boundaries).
The effect of this is that architectures with non-coherent DMA caches
may run into memory corruption or kernel crashes with Unhandled
kernel unaligned accesses exceptions.
Fix the alignment by positioning the DMA area in front of the allocation
and use memory at the end of the area for storing the orginal
transfer_buffer pointer. This may have the added benefit of increased
performance as the DMA area is now fully aligned on all architectures.
Tested with Lantiq xRX200 (MIPS) and RPi Model B Rev 2 (ARM).
Fixes: 3bc04e28a0 ("usb: dwc2: host: Get aligned DMA in a more supported way")
Cc: <stable@vger.kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
For unidirectional endpoints, the endpoint pointer will be NULL for the
unused direction. Check that the endpoint is active before
dereferencing this pointer.
Fixes: 1b4977c793 ("usb: dwc2: Update dwc2_handle_incomplete_isoc_in() function")
Fixes: 689efb2619 ("usb: dwc2: Update dwc2_handle_incomplete_isoc_out() function")
Fixes: d84845522d ("usb: dwc2: Update GINTSTS_GOUTNAKEFF interrupt handling")
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When handling split transactions we will try to delay retry after
getting a NAK from the device. This works well for BULK transfers that
can be polled for essentially forever. Unfortunately, on slower systems
at boot time, when the kernel is busy enumerating all the devices (USB
or not), we issue a bunch of control requests (reading device
descriptors, etc). If we get a NAK for the IN part of the control
request and delay retry for too long (because the system is busy), we
may confuse the device when we finally get to reissue SSPLIT/CSPLIT IN
and the device will respond with STALL. As a result we end up with
failure to get device descriptor and will fail to enumerate the device:
[ 3.428801] usb 2-1.2.1: new full-speed USB device number 9 using dwc2
[ 3.508576] usb 2-1.2.1: device descriptor read/8, error -32
[ 3.699150] usb 2-1.2.1: device descriptor read/8, error -32
[ 3.891653] usb 2-1.2.1: new full-speed USB device number 10 using dwc2
[ 3.968859] usb 2-1.2.1: device descriptor read/8, error -32
...
Let's not delay retries of split CONTROL IN transfers, as this allows us
to reliably enumerate devices at boot time.
Fixes: 38d2b5fb75 ("usb: dwc2: host: Don't retry NAKed transactions right away")
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
PID bitfield in descriptor should be set based on particular request
length, not based on EP's mc value. PID value can't be set to 0 even
request length is 0.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Freed allocated request for ep0 to prevent memory leak in case when
dwc2_driver_probe() failed.
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If isoc split in transfer with no data (the length of DATA0
packet is zero), we can't simply return immediately. Because
the DATA0 can be the first transaction or the second transaction
for the isoc split in transaction. If the DATA0 packet with no
data is in the first transaction, we can return immediately.
But if the DATA0 packet with no data is in the second transaction
of isoc split in transaction sequence, we need to increase the
qtd->isoc_frame_index and giveback urb to device driver if needed,
otherwise, the MDATA packet will be lost.
A typical test case is that connect the dwc2 controller with an
usb hs Hub (GL852G-12), and plug an usb fs audio device (Plantronics
headset) into the downstream port of Hub. Then use the usb mic
to record, we can find noise when playback.
In the case, the isoc split in transaction sequence like this:
- SSPLIT IN transaction
- CSPLIT IN transaction
- MDATA packet (176 bytes)
- CSPLIT IN transaction
- DATA0 packet (0 byte)
This patch use both the length of DATA0 and qtd->isoc_split_offset
to check if the DATA0 is in the second transaction.
Tested-by: Gevorg Sahakyan <sahakyan@synopsys.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Minas Harutyunyan hminas@synopsys.com>
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The commit 3bc04e28a0 ("usb: dwc2: host: Get aligned DMA in
a more supported way") rips out a lot of code to simply the
allocation of aligned DMA. However, it also introduces a new
issue when use isoc split in transfer.
In my test case, I connect the dwc2 controller with an usb hs
Hub (GL852G-12), and plug an usb fs audio device (Plantronics
headset) into the downstream port of Hub. Then use the usb mic
to record, we can find noise when playback.
It's because that the usb Hub uses an MDATA for the first
transaction and a DATA0 for the second transaction for the isoc
split in transaction. An typical isoc split in transaction sequence
like this:
- SSPLIT IN transaction
- CSPLIT IN transaction
- MDATA packet
- CSPLIT IN transaction
- DATA0 packet
The DMA address of MDATA (urb->dma) is always DWORD-aligned, but
the DMA address of DATA0 (urb->dma + qtd->isoc_split_offset) may
not be DWORD-aligned, it depends on the qtd->isoc_split_offset (the
length of MDATA). In my test case, the length of MDATA is usually
unaligned, this cause DATA0 packet transmission error.
This patch use kmem_cache to allocate aligned DMA buf for isoc
split in transaction. Note that according to usb 2.0 spec, the
maximum data payload size is 1023 bytes for each fs isoc ep,
and the maximum allowable interrupt data payload size is 64 bytes
or less for fs interrupt ep. So we set the size of object to be
1024 bytes in the kmem cache.
Tested-by: Gevorg Sahakyan <sahakyan@synopsys.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Minas Harutyunyan hminas@synopsys.com>
Signed-off-by: William Wu <william.wu@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The dwc2_get_ls_map() use ttport to reference into the
bitmap if we're on a multi_tt hub. But the bitmaps index
from 0 to (hub->maxchild - 1), while the ttport index from
1 to hub->maxchild. This will cause invalid memory access
when the number of ttport is hub->maxchild.
Without this patch, I can easily meet a Kernel panic issue
if connect a low-speed USB mouse with the max port of FE2.1
multi-tt hub (1a40:0201) on rk3288 platform.
Fixes: 9f9f09b048 ("usb: dwc2: host: Totally redo the microframe scheduler")
Cc: <stable@vger.kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Minas Harutyunyan hminas@synopsys.com>
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case when a hub is connected to DWC2 host
auto suspend occurs and host goes to
hibernation. When any device connected to hub
host hibernation exiting incorrectly.
- Added dwc2_hcd_rem_wakeup() function call to
exit from suspend state by remote wakeup.
- Increase timeout value for port suspend bit to be set.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Artur Petrosyan <arturp@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In ISOC OUT transfer, when the OUT token received while EP disabled,
we shouldn't complete a usb request. The current flow completed one
usb request, this will lead to a packet drop to function driver.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In ISOC transfer, when the NAK interrupt happens, we shouldn't complete
a usb request, the current flow will complete one usb request with no
hardware transfer, this will lead to a packet drop on the usb bus.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Zeng Tao <prime.zeng@hisilicon.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case of requests queue is empty reset EP target_frame to
initial value.
This allow restarting ISOC traffic in case when function
driver queued requests with interruptions.
Tested-by: Zeng Tao <prime.zeng@hisilicon.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When _param is unsigned and the minimum value of range is 0, it gives
the following warning:
COVERITY NO_EFFECT: This less-than-zero comparison of an unsigned value
is never true.
Converting ._param to int to avoid this warning.
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fix to return error code -ENOMEM from the alloc fail error handling
case instead of 0, as done elsewhere in this function.
Fixes: ecd29dabb2 ("usb: dwc2: pci: Handle error cleanup in probe")
Reviewed-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
By clearing NAK status of EP, core will send ZLP
to IN token and assert NAK interrupt relying
on TxFIFO status only.
The WA applies only to core versions from 2.72a
to 4.00a (including both). Also for FS_IOT_1.00a
and HS_IOT_1.00a.
Signed-off-by: Artur Petrosyan <arturp@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
devm_regulator_get_optional returns -ENODEV if the regulator isn't
there, so if that's the case we have to make sure not to leave -ENODEV
in the regulator pointer.
Also, make sure we return 0 in that case, but correctly propagate any
other errors. Also propagate the error from _dwc2_hcd_start.
Fixes: 531ef5ebea ("usb: dwc2: add support for host mode external vbus supply")
Cc: Amelie Delaunay <amelie.delaunay@st.com>
Reviewed-by: Amelie Delaunay <amelie.delaunay@st.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In 4.17-rc, commit 03ea6d6e9e ("usb: dwc2: Enable power down")
caused the HiKey board to not correctly handle switching between
usb-gadget and usb-host mode.
Unplugging the OTG port would result in:
[ 42.240973] dwc2 f72c0000.usb: dwc2_restore_host_registers: no host registers to restore
[ 42.249066] dwc2 f72c0000.usb: dwc2_host_exit_hibernation: failed to restore host registers
And the USB-host ports would not function.
And plugging in the OTG port, we would see:
[ 46.046557] WARNING: CPU: 3 PID: 6 at drivers/usb/dwc2/gadget.c:260 dwc2_hsotg_init_fifo+0x194/0x1a0
[ 46.055761] CPU: 3 PID: 6 Comm: kworker/u16:0 Not tainted 4.17.0-rc5-00030-ge67da8c #231
[ 46.055767] Hardware name: HiKey Development Board (DT)
[ 46.055784] Workqueue: dwc2 dwc2_conn_id_status_change
...
Thus, this patch sets the hisi params to disable the power_down
flag by default, and gets thing working again.
Cc: John Youn <johnyoun@synopsys.com>
Cc: Vardan Mikayelyan <mvardan@synopsys.com>
Cc: Artur Petrosyan <arturp@synopsys.com>
Cc: Grigor Tovmasyan <tovmasya@synopsys.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added descriptions for all not described parameters.
Fix all kernel doc's warnings.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The current frame_number is read from core for both
device and host modes. Reading of the current frame
number needs to be performed ASAP due to IRQ latency's.
This is why, it is moved to common interrupt handler.
Accordingly updated dwc2_gadget_target_frame_elapsed()
function which uses stored frame_number instead of
reading frame number.
In cases when target frame value is incremented
the frame_number is required to read again.
Signed-off-by: Artur Petrosyan <arturp@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Dumping the registers via debugfs makes USB on Raspberry Pi completely
unusable. The read of register GRXSTSP ("Receive Status Read and Pop
Register") is responsible for this behaviour, because it pops the RX FIFO.
So avoid this by omitting the relevant register.
CC: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Fixes: 563cf017c4 ("usb: dwc2: debugfs: add support for complete register dump")
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Crash caused by going out of "eps_out" array range.
Iteration on "eps_out" changed to less than "num_of_eps".
Signed-off-by: Artur Petrosyan <arturp@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added GHWCFG4_IPG_ISOC_SUPPORTED and DCFG_IPG_ISOC_SUPPORDED
bits definitions to enable/disable IPG feature.
Added ipg_isoc_en core parameter which will indicate IPG support
enable/disable and initialize it.
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In DDMA mode required to enable BNA interrupt for
both directions.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Changed existing two descriptor-chain flow to one chain.
In two-chain implementation BNA interrupt used for switching between
two chains. BNA interrupt asserted because of returning to
beginning of the chain based on L-bit of last descriptor.
Because of that we lose packets. This issue resolved by using one
desc-chain.
Removed all staff related to two desc-chain flow from
DDMA ISOC related functions.
Removed request length checking from dwc2_gadget_fill_isoc_desc()
function. Request length checking added to dwc2_hsotg_ep_queue()
function. If request length greater than descriptor limits then
request not added to queue. Additional checking done for High
Bandwidth ISOC OUT's which not supported by driver. In
dwc2_gadget_fill_isoc_desc() function also checked desc-chain
status (full or not) to avoid of reusing not yet processed
descriptors.
In dwc2_gadget_start_isoc_ddma() function creation of desc-chain
always started from descriptor 0. Before filling descriptors, they
were initialized by HOST BUSY status.
In dwc2_gadget_complete_isoc_request_ddma() added checking for
desc-chain rollover. Also added checking completion status.
Request completed successfully if DEV_DMA_STS is DEV_DMA_STS_SUCC,
otherwise complete with actual=0. For systems with high IRQ latency
added pointer compl_desc to next descriptor to be completed by
XferCompl interrupt. This pointer replace descriptor index calculation
based on DxEPDMA register. On descriptor completion interrupt
processing all descriptors starting from compl_desc till descriptor
which Buffer Status field not equal DMA_DONE status.
Actually removed dwc2_gadget_start_next_isoc_ddma() function because
now driver use only one desc-chain and instead that function added
dwc2_gadget_handle_isoc_bna() function for handling BNA interrupts.
Handling BNA interrupt done by flushing TxFIFOs for OUT EPs,
completing request with actual=0 and resetting desc-chain number and
target frame to initial values for restarting transfers.
On handling NAK request completed with actual=0. Incremented target
frame to allow fill desc chain and start transfers.
In DDMA mode avoided of frame number incrementing, because tracking
of frame number performed in dwc2_gadget_fill_isoc_desc() function.
When core assert XferCompl along with BNA, we should ignore XferCompl
in dwc2_hsotg_epint() function.
On BNA interrupt replaced dwc2_gadget_start_next_isoc_ddma() by above
mentioned BNA handler.
In dwc2_hsotg_ep_enable() function added sanity check of bInterval
for ISOC IN in DDMA mode, because HW doesn't supported EP's with
bInterval more than 10 and check for mc for ISOC OUT transfers,
because core doesn't support high bandwidth transfers.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Quite a lot happened in this cycle, with a total of 95 non-merge
commits. The most interesting parts are listed below:
Synopsys has been adding better support for USB 3.1 to dwc3. The same
series also sets g_mass_storage's max speed to SSP.
Roger Quadros (TI) added support for dual-role using the OTG block
available in some dwc3 implementations, this makes sure that AM437x
can swap roles in runtime.
We have a new SoC supported in dwc3 now - Amlogic Meson GX - thanks to
the work of Martin Blumenstingl.
We also have a ton of changes in dwc2 (51% of all changes, in
fact). The most interesting part there is the support for
Hibernation (a Synopsys PM feature).
Apart from these, we have our regular set of non-critical fixes all
over the place.
-----BEGIN PGP SIGNATURE-----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=F6OC
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-testing
Felipe writes:
usb: changes for v4.17 merge window
Quite a lot happened in this cycle, with a total of 95 non-merge
commits. The most interesting parts are listed below:
Synopsys has been adding better support for USB 3.1 to dwc3. The same
series also sets g_mass_storage's max speed to SSP.
Roger Quadros (TI) added support for dual-role using the OTG block
available in some dwc3 implementations, this makes sure that AM437x
can swap roles in runtime.
We have a new SoC supported in dwc3 now - Amlogic Meson GX - thanks to
the work of Martin Blumenstingl.
We also have a ton of changes in dwc2 (51% of all changes, in
fact). The most interesting part there is the support for
Hibernation (a Synopsys PM feature).
Apart from these, we have our regular set of non-critical fixes all
over the place.
Trivial fix to spelling mistake in dev_warn warning message text.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Declared dwc2_force_mode() function as static, because it was used
only in core.c file, for fixing sparse error.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch adds a way to enable an external vbus supply in host mode,
when dwc2 drvvbus signal is not used.
This patch is very similar to the one done in U-Boot dwc2 driver [1]. It
also adds dynamic vbus supply management depending on the role and state
of the core.
[1] https://lists.denx.de/pipermail/u-boot/2017-March/283434.html
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If the dr_mode is USB_DR_MODE_OTG, forcing the mode is needed during
driver probe to get the host and device specific HW parameters. Then we
clear the force mode bits so that the core operates in OTG mode.
The force mode bits should not be touched at any other time during the
driver lifetime and they should be preserved whenever the GUSBCFG
register is written to. The force mode bit values will persist across
soft resets of the core.
If the dr_mode is either USB_DR_MODE_HOST or USB_DR_MODE_PERIPHERAL, the
force mode is set just once at probe to configure the core as either a
host or peripheral.
Given the above, we no longer need any other reset delays, force delays,
or any forced modes anywhere else in the driver. So replace all calls to
dwc2_core_reset_and_force_dr_mode() with dwc2_core_reset() and remove
all other unnecessary delays.
Also remove the dwc2_force_mode_if_needed() function since the "if
needed" part is already taken care of by the polling in
dwc2_force_mode().
Finally, remove all other calls to dwc2_clear_force_mode().
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Enable the power down option based on the core capability.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: Artur Petrosyan <arturp@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The GPWRDN interrupts are those that occur in both Host and
Device mode while core is in hibernated state.
Export dwc2_core_init to be able to use it in GPWRDN_IDSTS
interrupt handler.
Here we have duplicated init functions in host and gadget sides
so I have left things as it was(used corresponing functions for
host and gadget), maybe in the future we'll resolve this problem
and will use dwc2_core_init for both sides.
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Artur Petrosyan <arturp@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Do changes to allow entering hibernated state from USB_SUSPEND
interrupt. All code is added under if conditions and mustn't impact
existing functionality.
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
These are wrapper functions which are calling device or host
enter/exit hibernation functions.
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add host/device hibernation functions which must be wrapped
by core's dwc2_enter_hibernation()/dwc2_exit_hibernation()
functions.
Make dwc2_backup_global_registers dwc2_restore_global_register
non-static to use them in both host/gadget sides.
Added function names:
dwc2_gadget_enter_hibernation()
dwc2_gadget_exit_hibernation()
dwc2_host_enter_hibernation()
dwc2_host_exit_hibernation()
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Artur Petrosyan <arturp@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add common (host/device) helper functions, which will be called while
exiting from hibernation, from both sides.
dwc2_restore_essential_regs()
dwc2_hib_restore_common()
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Artur Petrosyan <arturp@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Move hptxfsiz to host register's backup/restore functions, not
needed to have it in global register's backup/restore functions.
Add backup for glpmcfg, and read/write for gi2cctl and pcgcctl.
As requires programming guide.
Affected functions:
dwc2_backup_host_registers()
dwc2_restore_host_registers()
dwc2_backup_global_registers()
dwc2_restore_global_registers()
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It will be set once corresponding set_feature command comes.
True if device is allowed to wake-up host by remote-wakeup
signalling.
This is preparation for remote wake-up support implementation,
it will not be implemented until gadget stack provide interface
for bringing remote wake-up signalling.
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added a flag to indicate that core is in hibernation,
it is used to determine the hibernation state of the core.
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add parameter remote_wakeup to dwc2_restore_device_registers()
to be able to restore device registers according to programming
guide for dwc-otg. It says that in case of rem_wakeup DCTL must not
be restored here.
Remove setting of DCTL_PWRONPRGDONE from this function, because it
will be done in function responsible for exiting from hibernation.
WA for enabled EPx's IN and OUT in DDMA mode. On entering to
hibernation wrong value read and saved from DIEPDMAx,
as result BNA interrupt asserted on hibernation exit
by restoring from saved area.
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Artur Petrosyan <arturp@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Moved dtxfsiz from dwc2_gregs_backup to dwc2_dregs_backup,
because it is device register.
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add parameter and it's initialization, needed for hibernation.
Reimplement dwc2_set_param_power_down() to support hibernation too.
Now 'power_down' parameter can be initialized with 0, 1 or 2.
0 - No
1 - Partial power down
2 - Hibernation
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
No-op change, only rename.
This code was misnamed originally. It was only responsible for partial
power down and not for hibernation.
Rename core_params->hibernation to core_params->power_down,
dwc2_set_param_hibernation() to dwc2_set_param_power_down().
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Set 'lpm_capable' flag in the gadget structure so
indicating that LPM is supported.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Sevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Assign true or false to boolean variables instead of an integer value.
This issue was detected with the help of Coccinelle.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added core state checking in dwc2_hsotg_ep_queue() function
to make sure that application will submit requests only in L0 state.
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added call_gadget() function call when entering to L1 state
to inform gadget that core is in L1 state.
Did the same thing when exiting from L1 state
to inform gadget that core is in L0 state.
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Configure core in device mode to support LPM according to
programming guide.
Device will start giving valid responses for LPM tokens.
After this patch device side LPM will start working.
Signed-off-by: Sevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This interrupt indicates that an LPM transaction
was received on the USB bus. After getting this
interrupt we are going from L0 state to L1 state.
Signed-off-by: Sevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add a function which will be called if device is in L1 sleep state
and Resume/Remote Wakeup Detected interrupt is asserted.
Signed-off-by: Sevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add lpm, lpm_clock_gating, besl, hird_threshold_en and hird_threshold
core parameters. These will indicate LPM and LPM Errata support
as well as chosen L1 sleeping mode for the core and PHY.
Signed-off-by: Sevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Make field names of GLPMCFG register in definitions to be
the same with the databook.
Signed-off-by: Sevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Backup PCGCCTL1 register when entering hibernation mode and
restore it after exiting from hibernation, to keep active ACG
feature.
Signed-off-by: Razmik Karapetyan <razmik@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added function for supporting Active Clock Gating functionality
in the driver.
PCGCCTL1 (Power and Clock Control) register will be used
for controlling the core`s active clock gating feature, and
the previously reserved 12th bit in GHWCFG4 now indicates that the
controller supports the Dynamic Power Reduction (Active Clock Gating)
during no traffic scenarios such as L0, idle, resume and suspend
states.
dwc2_enable_acg() function sets GATEEN bit in PCGCCTL1 register
and enables ACG, if it supported.
According to ACG functional specification, enabling of ACG feature
in host mode done in host initialization, before turning Vbus on,
specifically in dwc2_core_host_init function.
Enabling of ACG feature in device mode done in device initialization,
before clearing the SftDiscon bit in DCTL.
This bit was cleared in dwc2_hsotg_core_connect() function.So
dwc2_enable_acg() called before dwc2_core_connect() calls.
Signed-off-by: Razmik Karapetyan <razmik@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We better print an error in case probing of dwc2 fails on
setting the DMA coherent mask.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The maximum value that unsigned char can hold is 255, meanwhile
the maximum value of interval is 2^(bIntervalMax-1)=2^15.
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The probe function doesn't properly handle errors. Fix it so that it
properly handles cleanup.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
After platform_device_add(), if we error out, we must do
platform_device_unregister(), which also does the put. So lets move
devm_kzalloc() to simplify error handling and avoid calling of
platform_device_unregister().
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Move usb_phy_generic_register() function call to the top, to simplify
error handling. If this fails we can simply return instead of cleaning
up.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Use devm_kzalloc() and remove the unnecessary kfree().
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Before flushing fifos required to check AHB master state and
lush when AHB master is in IDLE state.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added missing GUSBCFG programming in host mode, which fixes
transaction errors issue on HiKey and Altera Cyclone V boards.
These field even if was programmed in device mode (in function
dwc2_hsotg_core_init_disconnected()) will be resetting to POR values
after core soft reset applied.
So, each time when switching to host mode required to set this field
to correct value.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
According databook in Buffer and External DMA mode
non-split periodic channels can't be halted.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Removed unnecessary debug prints about DMA mode for host side
from dwc2_gahbcfg_init() function.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Razmik Karapetyan <razmik@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Deleted dwc2_hcd_dump_frrem() function, because it used undefined
parameters from dwc2_hsotg structure. The function body was in #ifdef
statement and was never compiled.
Also removed that parameters from dwc2_hsotg structure, which were
used only in dwc2_hcd_dump_frrem() function.
And also delete dwc2_sample_frrem macro, because without
dwc2_hcd_dump_frrem() function it's lose its purpose.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Renamed __orr32 and __bic32 function names to more descriptive
dwc2_set_bit and dwc2_clear_bit respectively.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Razmik Karapetyan <razmik@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Disabled only unmasked endpoints based on DAINTMSK register.
This will allow to minimize GINTSTS_GOUTNAKEFF interrupt handling.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Razmik Karapetyan <razmik@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In 'for' loop skipped masked and non-ISOC EPs. Also breaked 'for' loop
after setting SGOUTNAK in DCTL,when one enabled EP was detected.
This will allow to minimize incomplete ISOC OUT interrupt handling.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Razmik Karapetyan <razmik@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Disabled only that ISOC endpoints,for which interrupt bit was set
in the DAINTMSK register. This will allow to minimize incomplete
ISOC IN interrupt handling.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Razmik Karapetyan <razmik@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Changed AHB burst size from INCR4 to INCR by default.
With this value driver shows excellent DMA performance.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Razmik Karapetyan <razmik@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In dwc2_hsotg_core_init_disconnected() function used AHB burst size
parameter, instead of calculating already calculated value.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Razmik Karapetyan <razmik@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Move dwc2_hsotg_wait_bit_set function to core.c so it can be used
anywhere in the code.
Added dwc2_hsotg_wait_bit_clear function in core.c.
Replace all the parts of register bit polling code with
dwc2_hsotg_wait_bit_set or dwc2_hsotg_wait_bit_clear functions
calls depends on code logic.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Sevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Only check the ID portion of the GSNPSID register and don’t check
the version. This will allow the driver to work with version 4.00a
and later of the DWC_hsotg IP.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gevorg Sahakyan <sahakyan@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Cc: John Youn <johnyoun@synopsys.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The irq is available in hsotg already, so there's no need to pass it as
separate function parameter.
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Cc: John Youn <johnyoun@synopsys.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch fixes compatible for STM32F7 USB OTG HS and consistently rename
dw2_set_params function.
The v2 former patch [1] had been acked by Paul Young, but v1 was merged.
[1] https://patchwork.kernel.org/patch/9925573/
Fixes: d8fae8b936 ("usb: dwc2: add support for STM32F7xx USB OTG HS")
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We should call dwc2_hsotg_enqueue_setup() after properly
setting lx_state. Because it may cause error-out from
dwc2_hsotg_enqueue_setup() due to wrong value in lx_state.
Issue can be reproduced by loading driver while connected
A-Connector (start in A-HOST mode) then disconnect A-Connector
to switch to B-DEVICE.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
STSPHSERCVD (status phase received) interrupt should be
handled when EP0 is in DWC2_EP0_DATA_OUT state.
Sometimes STSPHSERCVD interrupt asserted , when EP0
is not in DATA_OUT state. Spurios interrupt.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In some cases device sending ZLP IN on non EP0 which
reassigning EP0 OUT descriptor pointer to that EP.
Dedicated for EP0 OUT descriptor multiple time re-used by
other EP while that descriptor already in use by EP0 OUT
for SETUP transaction. As result when SETUP packet received
BNA interrupt asserting.
In dwc2_hsotg_program_zlp() function dwc2_gadget_set_ep0_desc_chain()
must be called only for EP0.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Not many changes here, the most important being an improvement for TI's
AM57xx and DRA7xx devices which allows them to disable a metastability
workaround in situations where we know what's going on.
Other than that, we have a set of changes on Renesas UDC to make the
code a little easier to read and maintain while also better supporting
extcon framework.
The u_serial adaptation layer learned to use kfifo instead of cooking
its own FIFO implementation.
DWC3 learned to decode a few more USB requests on the trace output.
-----BEGIN PGP SIGNATURE-----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=uwh/
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: changes for v4.16 merge window
Not many changes here, the most important being an improvement for TI's
AM57xx and DRA7xx devices which allows them to disable a metastability
workaround in situations where we know what's going on.
Other than that, we have a set of changes on Renesas UDC to make the
code a little easier to read and maintain while also better supporting
extcon framework.
The u_serial adaptation layer learned to use kfifo instead of cooking
its own FIFO implementation.
DWC3 learned to decode a few more USB requests on the trace output.
On rk3288-veyron devices on Chrome OS it was found that plugging in an
Arduino-based USB device could cause the system to lockup, especially
if the CPU Frequency was at one of the slower operating points (like
100 MHz / 200 MHz).
Upon tracing, I found that the following was happening:
* The USB device (full speed) was connected to a high speed hub and
then to the rk3288. Thus, we were dealing with split transactions,
which is all handled in software on dwc2.
* Userspace was initiating a BULK IN transfer
* When we sent the SSPLIT (to start the split transaction), we got an
ACK. Good. Then we issued the CSPLIT.
* When we sent the CSPLIT, we got back a NAK. We immediately (from
the interrupt handler) started to retry and sent another SSPLIT.
* The device kept NAKing our CSPLIT, so we kept ping-ponging between
sending a SSPLIT and a CSPLIT, each time sending from the interrupt
handler.
* The handling of the interrupts was (because of the low CPU speed and
the inefficiency of the dwc2 interrupt handler) was actually taking
_longer_ than it took the other side to send the ACK/NAK. Thus we
were _always_ in the USB interrupt routine.
* The fact that USB interrupts were always going off was preventing
other things from happening in the system. This included preventing
the system from being able to transition to a higher CPU frequency.
As I understand it, there is no requirement to retry super quickly
after a NAK, we just have to retry sometime in the future. Thus one
solution to the above is to just add a delay between getting a NAK and
retrying the transmission. If this delay is sufficiently long to get
out of the interrupt routine then the rest of the system will be able
to make forward progress. Even a 25 us delay would probably be
enough, but we'll be extra conservative and try to delay 1 ms (the
exact amount depends on HZ and the accuracy of the jiffy and how close
the current jiffy is to ticking, but could be as much as 20 ms or as
little as 1 ms).
Presumably adding a delay like this could impact the USB throughput,
so we only add the delay with repeated NAKs.
NOTE: Upon further testing of a pl2303 serial adapter, I found that
this fix may help with problems there. Specifically I found that the
pl2303 serial adapters tend to respond with a NAK when they have
nothing to say and thus we end with this same sequence.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The dwc2 USB controller in Stratix10 has an additional ECC reset bit that
needs to get de-asserted in order for the controller to work properly.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In host mode reading from DPTXSIZn returning invalid value in
dwc2_check_param_tx_fifo_sizes function.
In total TxFIFO size calculations unnecessarily reducing by ep_info.
hw->total_fifo_size can be fully allocated for FIFO's.
Added num_dev_in_eps member in dwc2_hw_params structure to save number
of IN EPs.
Added g_tx_fifo_size array in dwc2_hw_params structure to store power
on reset values of DPTXSIZn registers in forced device mode.
Updated dwc2_hsotg_tx_fifo_count() function to get TxFIFO count from
num_dev_in_eps.
Updated dwc2_get_dev_hwparams() function to store DPTXFSIZn in
g_tx_fifo_size array.
dwc2_get_host/dev_hwparams() functions call moved after num_dev_in_eps
set from hwcfg4.
Modified dwc2_check_param_tx_fifo_sizes() function to check TxFIFOn
sizes based on g_tx_fifo_size array.
Removed ep_info subtraction during calculation of tx_addr_max in
dwc2_hsotg_tx_fifo_total_depth() function. Also removed
dwc2_hsotg_ep_info_size() function as no more need.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gevorg Sahakyan <sahakyan@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Here is the big set of USB and PHY driver updates for 4.15-rc1.
There is the usual amount of gadget and xhci driver updates, along with
phy and chipidea enhancements. There's also a lot of SPDX tags and
license boilerplate cleanups as well, which provide some churn in the
diffstat.
Other major thing is the typec code that moved out of staging and into
the "real" part of the drivers/usb/ tree, which was nice to see happen.
All of these have been in linux-next with no reported issues for a
while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWgm/Vw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yktXwCdGgpInfOEvOGFd83EPDL7a1ncyc4AoM5wI8yl
1CeLipqVIN3IsMMJptvb
=zvDI
-----END PGP SIGNATURE-----
Merge tag 'usb-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big set of USB and PHY driver updates for 4.15-rc1.
There is the usual amount of gadget and xhci driver updates, along
with phy and chipidea enhancements. There's also a lot of SPDX tags
and license boilerplate cleanups as well, which provide some churn in
the diffstat.
Other major thing is the typec code that moved out of staging and into
the "real" part of the drivers/usb/ tree, which was nice to see
happen.
All of these have been in linux-next with no reported issues for a
while"
* tag 'usb-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (263 commits)
usb: gadget: f_fs: Fix use-after-free in ffs_free_inst
USB: usbfs: compute urb->actual_length for isochronous
usb: core: message: remember to reset 'ret' to 0 when necessary
USB: typec: Remove remaining redundant license text
USB: typec: add SPDX identifiers to some files
USB: renesas_usbhs: rcar?.h: add SPDX tags
USB: chipidea: ci_hdrc_tegra.c: add SPDX line
USB: host: xhci-debugfs: add SPDX lines
USB: add SPDX identifiers to all remaining Makefiles
usb: host: isp1362-hcd: remove a couple of redundant assignments
USB: adutux: remove redundant variable minor
usb: core: add a new usb_get_ptm_status() helper
usb: core: add a 'type' parameter to usb_get_status()
usb: core: introduce a new usb_get_std_status() helper
usb: core: rename usb_get_status() 'type' argument to 'recip'
usb: core: add Status Type definitions
USB: gadget: Remove redundant license text
USB: gadget: function: Remove redundant license text
USB: gadget: udc: Remove redundant license text
USB: gadget: legacy: Remove redundant license text
...
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: John Youn <johnyoun@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
Update the drivers/usb/ and include/linux/usb* files with the correct
SPDX license identifier based on the license text in the file itself.
The SPDX identifier is a legally binding shorthand, which can be used
instead of the full boiler plate text.
This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It has been noticed that the dwc2 udc state reporting doesn't
seem to work (at least on HiKey boards). Where after the initial
setup, the sysfs /sys/class/udc/f72c0000.usb/state file would
report "configured" no matter the state of the OTG port.
This patch adds a call so that we report to the UDC layer when
the gadget device is disconnected.
This patch does depend on the previous patch ("usb: dwc2:
Improve gadget state disconnection handling") in this patch set
in order to properly work.
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: YongQin Liu <yongqin.liu@linaro.org>
Cc: John Youn <johnyoun@synopsys.com>
Cc: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Chen Yu <chenyu56@huawei.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Tested-by: Minas Harutyunyan <hminas@synopsys.com>
Reported-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We've found that while in host mode, using Android, if one runs
the command:
stop adbd
The existing usb devices being utilized in host mode are disconnected.
This is most visible with usb networking devices.
This seems to be due to adbd closing the file:
/dev/usb-ffs/adb/ep0
Which calls ffs_ep0_release() and the following backtrace:
[<ffffff800875a430>] dwc2_hsotg_ep_disable+0x148/0x150
[<ffffff800875a498>] dwc2_hsotg_udc_stop+0x60/0x110
[<ffffff8008787950>] usb_gadget_remove_driver+0x58/0x78
[<ffffff80087879e4>] usb_gadget_unregister_driver+0x74/0xe8
[<ffffff80087850c0>] unregister_gadget+0x28/0x58
[<ffffff800878511c>] unregister_gadget_item+0x2c/0x40
[<ffffff8008790ea8>] ffs_data_clear+0xe8/0xf8
[<ffffff8008790ed8>] ffs_data_reset+0x20/0x58
[<ffffff8008793218>] ffs_data_closed+0x98/0xe8
[<ffffff80087932d8>] ffs_ep0_release+0x20/0x30
Then when dwc2_hsotg_ep_disable() is called, we call
kill_all_requests() which causes a bunch of the following
messages:
dwc2 f72c0000.usb: Mode Mismatch Interrupt: currently in Host mode
dwc2 f72c0000.usb: Mode Mismatch Interrupt: currently in Host mode
dwc2 f72c0000.usb: Mode Mismatch Interrupt: currently in Host mode
dwc2 f72c0000.usb: Mode Mismatch Interrupt: currently in Host mode
dwc2 f72c0000.usb: Mode Mismatch Interrupt: currently in Host mode
dwc2 f72c0000.usb: Mode Mismatch Interrupt: currently in Host mode
dwc2 f72c0000.usb: Mode Mismatch Interrupt: currently in Host mode
dwc2 f72c0000.usb: Mode Mismatch Interrupt: currently in Host mode
init: Service 'adbd' (pid 1915) killed by signal 9
init: Sending signal 9 to service 'adbd' (pid 1915) process group...
init: Successfully killed process cgroup uid 0 pid 1915 in 0ms
init: processing action (init.svc.adbd=stopped) from (/init.usb.configfs.rc:15)
dwc2 f72c0000.usb: dwc2_hc_chhltd_intr_dma: Channel 8 - ChHltd set, but reason is unknown
dwc2 f72c0000.usb: hcint 0x00000002, intsts 0x04200029
dwc2 f72c0000.usb: dwc2_hc_chhltd_intr_dma: Channel 12 - ChHltd set, but reason is unknown
dwc2 f72c0000.usb: hcint 0x00000002, intsts 0x04200029
dwc2 f72c0000.usb: dwc2_hc_chhltd_intr_dma: Channel 15 - ChHltd set, but reason is unknown
dwc2 f72c0000.usb: hcint 0x00000002, intsts 0x04200029
dwc2 f72c0000.usb: dwc2_hc_chhltd_intr_dma: Channel 3 - ChHltd set, but reason is unknown
dwc2 f72c0000.usb: hcint 0x00000002, intsts 0x04200029
dwc2 f72c0000.usb: dwc2_hc_chhltd_intr_dma: Channel 4 - ChHltd set, but reason is unknown
dwc2 f72c0000.usb: hcint 0x00000002, intsts 0x04200029
dwc2 f72c0000.usb: dwc2_update_urb_state_abn(): trimming xfer length
And the usb devices connected are basically hung at this point.
It seems like if we're in host mode, we probably shouldn't run
the dwc2_hostg_ep_disable logic, so this patch returns an error
in that case.
With this patch (along with the previous patch in this set), we avoid
the mismatched interrupts and connected usb devices continue to function.
I'm not sure if some other solution would be better here, but this seems
to work, so I wanted to send it out for input on what the right approach
should be.
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: YongQin Liu <yongqin.liu@linaro.org>
Cc: John Youn <johnyoun@synopsys.com>
Cc: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Chen Yu <chenyu56@huawei.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Tested-by: Minas Harutyunyan <hminas@synopsys.com>
Reported-by: YongQin Liu <yongqin.liu@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In the earlier commit dad3f793f2 ("usb: dwc2: Make sure we
disconnect the gadget state"), I was trying to fix up the
fact that we somehow weren't disconnecting the gadget state,
so that when the OTG port was plugged in the second time we
would get warnings about the state tracking being wrong.
(This seems to be due to a quirk of the HiKey board where
we do not ever get any otg interrupts, particularly the session
end detected signal. Instead we only see status change
interrupt.)
The fix there was somewhat simple, as it just made sure to
call dwc2_hsotg_disconnect() before we connected things up
in OTG mode, ensuring the state handling didn't throw errors.
But in looking at a different issue I was seeing with UDC
state handling, I realized that it would be much better
to call dwc2_hsotg_disconnect when we get the state change
signal moving to host mode.
Thus, this patch removes the earlier disconnect call I added
and moves it (and the needed locking) to the host mode
transition.
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: YongQin Liu <yongqin.liu@linaro.org>
Cc: John Youn <johnyoun@synopsys.com>
Cc: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Chen Yu <chenyu56@huawei.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Tested-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
For the case where an external VBUS is used, we should enable the external
VBUS comparator in the driver. This would prevent an unnecessary
overcurrent error which would then disable the host port.
This patch uses the standard 'disable-over-current' binding to allow of the
option of disabling the over-current condition.
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch adds the dwc2_set_params function for STM32F7xx USB OTG HS.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In the case hcd autosuspend is enabled, the hcd will enter L2 state
if no device connected. But if the controller works in otg mode, the
gadget driver still works in L0 state if connected with host. This
may result in transfer fail when gadget enqueue new request but the
hcd driver has set the global state into L2. This patch prevent the
hcd enter L2 state if the controller work in device mode.
Signed-off-by: Meng Dongyang <daniel.meng@rock-chips.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Make the structure const as it is only stored in the ops field of a
usb_ep structure, which is of type const.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Reseted DEVADDR field in DCFG to zero on USB RESET.
Device address in DCFG register does not reset to zero,
which required to pass enumeration, after disconnect and
reconnect.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
USB support in the Meson8 SoCs is provided by a DWC2 controller which
works with the same settings as Meson8b and GXBB. Using the generic
"snps,dwc2" binding results in an endless stream of "Overcurrent change
detected" messages.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
With 51 non-merge commits, this is one of the smallest USB Gadget pull
requests. Apart from your expected set of non-critical fixes, and
other miscellaneous items, we have most of the changes in dwc3 (52.5%)
with all other UDCs following with 34.8%.
As for the actual changes, the most important of them are all the
recent changes to reduce memory footprint of dwc3, bare minimum
dual-role support on dwc3 and reworked endpoint count and
initialization routines.
-----BEGIN PGP SIGNATURE-----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=wYOI
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: changes for v4.12
With 51 non-merge commits, this is one of the smallest USB Gadget pull
requests. Apart from your expected set of non-critical fixes, and
other miscellaneous items, we have most of the changes in dwc3 (52.5%)
with all other UDCs following with 34.8%.
As for the actual changes, the most important of them are all the
recent changes to reduce memory footprint of dwc3, bare minimum
dual-role support on dwc3 and reworked endpoint count and
initialization routines.
As of commit bb475230b8 ("reset: make optional functions really
optional"), the reset framework API calls use NULL pointers to describe
optional, non-present reset controls.
This allows to return errors from devm_reset_control_get_optional and to
call reset_control_(de)assert unconditionally.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch introduces a new parameter to activate USB OTG HS/FS core
embedded phy transceiver. The STM32F4x9 SoC uses the GGPIO register
to enable the transceiver.
Also add the dwc2_set_params function for stm32f4 otg fs.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Bruno Herrera <bruherrera@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
I had seen some odd behavior with HiKey's usb-gadget interface
that I finally seemed to have chased down. Basically every other
time I plugged in the OTG port, the gadget interface would
properly initialize. The other times, I'd get a big WARN_ON
in dwc2_hsotg_init_fifo() about the fifo_map not being clear.
Ends up if we don't disconnect the gadget state, the fifo-map
doesn't get cleared properly, which causes WARN_ON messages and
also results in the device not properly being setup as a gadget
every other time the OTG port is connected.
So this patch adds a call to dwc2_hsotg_disconnect() in the
reset path so the state is properly cleared.
With it, the gadget interface initializes properly on every
plug in.
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: John Youn <johnyoun@synopsys.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Chen Yu <chenyu56@huawei.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
a lot of embeded system SOC (e.g. freescale T2080) have both
PCI and USB modules. But USB module is controlled by registers directly,
it have no relationship with PCI module.
when say N here it will not build PCI related code in USB driver.
Signed-off-by: yuan linyu <Linyu.Yuan@alcatel-sbell.com.cn>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the big pull request for the Gadget
API. Again the majority of changes sit in dwc2
driver. Most important changes contain a workaround
for GOTGCTL being wrong, a sleep-inside-spinlock fix
and the big series of cleanups on dwc2.
One important thing on dwc3 is that we don't anymore
need gadget drivers to cope with unaligned OUT
transfers for us. We have support for appending one
extra chained TRB to align transfer ourselves.
Apart from these, the usual set of typos,
non-critical fixes, etc.
-----BEGIN PGP SIGNATURE-----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=gk8j
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
USB: changes for v4.11
Here's the big pull request for the Gadget
API. Again the majority of changes sit in dwc2
driver. Most important changes contain a workaround
for GOTGCTL being wrong, a sleep-inside-spinlock fix
and the big series of cleanups on dwc2.
One important thing on dwc3 is that we don't anymore
need gadget drivers to cope with unaligned OUT
transfers for us. We have support for appending one
extra chained TRB to align transfer ourselves.
Apart from these, the usual set of typos,
non-critical fixes, etc.
The irq is available in hsotg already, so there's no need to
pass it as separate function parameter.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Set the iomem parameters in the usb_hcd to fix this misleading
message during driver load:
dwc2 c9100000.usb: irq 22, io mem 0x00000000
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add dwc2_check_param_tx_fifo_sizes function which validates
the members of g_tx_fifo_size array and sets to average or
default values if it is needed.
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Sevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Remove legacy DWC2_G_P_LEGACY_TX_FIFO_SIZE array for TX FIFOs.
Update dwc2_set_param_tx_fifo_sizes function to calculate
and assign default average FIFO depth to each member of
g_tx_fifo_size array. Total FIFO size, EP Info block's size,
FIFO operation mode and device operation mode are taken into
consideration during the calculation.
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Sevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
GDFIFOCFG is available from IP version 2.91a. Fix the code to reflect
this.
Signed-off-by: Sevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
ulseep_range() uses hrtimers and provides no advantage over msleep()
for larger delays. Fix up the 100ms delays here passing the adjusted "min"
value to msleep(). This helps reduce the load on the hrtimer subsystem.
Link: http://lkml.org/lkml/2017/1/11/377
Fixes: commit 2938fc63e0 ("usb: dwc2: Properly account for the force mode delays")
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The Hi6220's usb controller is limited in that it does not
support "Split Transactions", so it does not support communicating
with low-speed and full-speed devices behind a high-speed hub.
Thus it requires a quirk so that we can manually drop the usb
speed when low/full-speed are attached, and bump back to high
speed when they are removed.
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: John Youn <johnyoun@synopsys.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Chen Yu <chenyu56@huawei.com>
Cc: Vardan Mikayelyan <mvardan@synopsys.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Chen Yu <chenyu56@huawei.com>
[jstultz: Reworked to simplify the patch, and made
commit log to be more specific about the issue]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We've seen failures when switching between host and gadget mode,
which was diagnosed as being caused due to the bus being
auto-suspended when we switched.
So this patch forces a port resume when switching to device
mode if the bus is suspended.
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: John Youn <johnyoun@synopsys.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Chen Yu <chenyu56@huawei.com>
Cc: Vardan Mikayelyan <mvardan@synopsys.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Chen Yu <chenyu56@huawei.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When removing a USB-A to USB-otg adapter cable, we get a change status
irq, and then in dwc2_conn_id_status_change, we erroneously see the
GOTGCTL_CONID_B flag set. This causes us to get stuck in the
"while (!dwc2_is_device_mode(hsotg))" loop, spitting out "Waiting for
Peripheral Mode, Mode=Host" warnings until it fails out many seconds
later.
This patch works around the issue by re-reading the GOTGCTL state to
check if the GOTGCTL_CONID_B is still set and if not restarting the
change status logic.
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: John Youn <johnyoun@synopsys.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Chen Yu <chenyu56@huawei.com>
Cc: Vardan Mikayelyan <mvardan@synopsys.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Reviewed-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Basically when plugging in various cables in different orders, I'm
occasionally seeing the following BUG splat:
[ 86.215403] BUG: scheduling while atomic: kworker/u16:2/53/0x00000002
[ 86.219164] usb 1-1: USB disconnect, device number 9
[ 86.226845] Preemption disabled at:[ 86.230218]
[<ffffff8008673558>] dwc2_conn_id_status_change+0x120/0x250
[ 86.236894] CPU: 0 PID: 53 Comm: kworker/u16:2 Tainted: G W
4.9.0-rc8-00051-gd5a7979-dirty #1702
[ 86.246836] Hardware name: HiKey Development Board (DT)
[ 86.252100] Workqueue: dwc2 dwc2_conn_id_status_change
[ 86.257279] Call trace:
[ 86.259771] [<ffffff8008087c28>] dump_backtrace+0x0/0x1a0
[ 86.265210] [<ffffff8008087ddc>] show_stack+0x14/0x20
[ 86.270308] [<ffffff80084343f0>] dump_stack+0x90/0xb0
[ 86.275401] [<ffffff80080d8d94>] __schedule_bug+0x6c/0xb8
[ 86.280841] [<ffffff8008a07220>] __schedule+0x4f8/0x5b0
[ 86.286099] [<ffffff8008a073e8>] schedule+0x38/0xa0
[ 86.291017] [<ffffff8008a0a6cc>] schedule_hrtimeout_range_clock+0x8c/0xf0
[ 86.297846] [<ffffff8008a0a740>] schedule_hrtimeout_range+0x10/0x18
[ 86.304150] [<ffffff8008a0a4a0>] usleep_range+0x50/0x58
[ 86.309418] [<ffffff800866d8dc>] dwc2_wait_for_mode.isra.4+0x54/0xd0
[ 86.315815] [<ffffff800866f058>] dwc2_core_reset+0xe0/0x168
[ 86.321431] [<ffffff800867e364>] dwc2_hsotg_core_init_disconnected+0x2c/0x310
[ 86.328602] [<ffffff8008673568>] dwc2_conn_id_status_change+0x130/0x250
[ 86.335254] [<ffffff80080ccd48>] process_one_work+0x118/0x370
[ 86.341035] [<ffffff80080ccfe8>] worker_thread+0x48/0x498
[ 86.346473] [<ffffff80080d2eb0>] kthread+0xd0/0xe8
[ 86.351299] [<ffffff8008082e80>] ret_from_fork+0x10/0x50
This seems to be caused by the dwc2_wait_for_mode() calling
usleep_range() while the hstog->lock spinlock is held, since
we take that before calling dwc2_hsotg_core_init_disconnected().
This patch avoids the issue by adding an extra argument to
dwc2_core_reset(), as suggested by John Youn, which allows us to
skip the waiting, which should be unnecessary when calling from
dwc2_hsotg_core_init_disconnected().
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: John Youn <johnyoun@synopsys.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Chen Yu <chenyu56@huawei.com>
Cc: Vardan Mikayelyan <mvardan@synopsys.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Show the value of dr_mode via a debufs file.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Further reduce the set of parameters set by platforms. Many of them are
unnecessary as they should be reported by hardware. They should only
need to be overridden if there is a problem.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Check these parameters only for true or false. There is no need to check
for greater or less than 0.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Remove the platform-specific static param structs and set only those
params that are necessary for each platform.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Check that core parameters have valid values and adjust them if they
aren't.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Group the members by global, host, and gadget params. Formatting and
organizational change only.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Update the param types to appropriately sized ints and bools.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
After setting the default core parameter values, read in the device
properties and modify core parameter values if needed.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Initialize the core parameters to their default, auto-detected values.
Remove all the previous dwc2_set_param* methods. Most of what this code
is doing is handling defaults for "not set" values and other trivial
checks. The checking can be simplified and will be done in a later
commit.
This allows us to change only those parameters that won't work with
default settings. It also allows us to use non-int parameters.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The otg_ver parameter only controls the SRP pulsing method and defaults
to the 1.3 behavior. It is unused and can be removed.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add programming of GDFIFOCFG register in device mode.
It must contain start address for EP Info block and
total FIFO depth.
Signed-off-by: Sevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Take the sizeof '*req' instead of 'struct dwc2_hsotg_req'.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The function returns void so a return is unnecessary.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
* Remove braces for one-line statements
* Add missing braces where another arm in if-statement uses braces
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fix the formatting of logical statements to end the line with the
logical operator.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fix misaligned and over 80-character comments.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fixes checkpatch warning:
WARNING: function definition argument 'struct dwc2_hsotg *' should also
have an identifier name
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This commmit is the result of running checkpatch --fix.
The results were verified for correctness. Some of the fixes result in
line over 80 char which we will fix manually later.
The following is a summary of what was done by checkpatch:
* Remove externs on function prototypes.
* Replace symbolic permissions with octal.
* Align code to open parens.
* Replace 'unsigned' with 'unsigned int'.
* Remove unneccessary blank lines.
* Add blank lines after declarations.
* Add spaces around operators.
* Remove unnecessary spaces after casts.
* Replace 'x == NULL' with '!x'.
* Replace kzalloc() with kcalloc().
* Concatenate multi-line strings.
* Use the BIT() macro.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
For boolean variables true/false is preferred over 1/0 for readability.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
ulseep_range() uses hrtimers and provides no advantage over msleep()
for larger delays. Fix up the 20+ ms delays here passing the adjusted "min"
value to msleep(). This helps reduce the load on the hrtimer subsystem.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Commit 05ee799f20 ("usb: dwc2: Move gadget settings into core_params")
changes to type u16 for DT binding "g-rx-fifo-size" and
"g-np-tx-fifo-size" but use type u32 for "g-tx-fifo-size". Finally the
the first two parameters cannot be passed successfully with wrong data
format. This is found the data transferring broken on 96boards Hikey.
This patch is to change all parameters to u32 type, and verified on
Hikey board the DT parameters can pass successfully.
[johnyoun: minor rebase]
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Uninitialized char* causes a sparse build-warning, fix it up by
initializing it to NULL.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
USBTrdTim must be programmed to 0x5 when phy has a UTMI+ 16-bit wide
interface or 0x9 when it has a 8-bit wide interface.
GUSBCFG reset value (Value After Reset: 0x1400) sets USBTrdTim to 0x5.
In case of 8-bit UTMI+, without clearing GUSBCFG.USBTRDTIM mask, USBTrdTim
results in 0xD (0x5 | 0x9).
That's why we need to clear GUSBCFG.USBTRDTIM mask before setting USBTrdTim
value, to ensure USBTrdTim is correctly set in case of 8-bit UTMI+.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
I've found when booting HiKey with the usb gadget cable attached
if I then try to connect via adb, I get an infinite spew of:
dwc2 f72c0000.usb: dwc2_hsotg_ep_sethalt(ep ffffffc0790ecb18 ep1out, 0)
dwc2 f72c0000.usb: dwc2_hsotg_ep_sethalt(ep ffffffc0790eca18 ep1in, 0)
It seems that the usb autosuspend is suspending the bus shortly
after bootup when the gadget cable is attached. So when adbd
then tries to use the device, it doesn't work and it then tries
to restart it over and over via the ep_sethalt calls (via
FUNCTIONFS_CLEAR_HALT ioctl).
Chen Yu suggested this patch to avoid suspending if we're
in device mode, and it avoids the problem.
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: John Youn <johnyoun@synopsys.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Chen Yu <chenyu56@huawei.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Suggested-by: Chen Yu <chenyu56@huawei.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Commit 05ee799f20 ("usb: dwc2: Move gadget settings into core_params")
changes to type u16 for DT binding "g-rx-fifo-size" and
"g-np-tx-fifo-size" but use type u32 for "g-tx-fifo-size". Finally the
the first two parameters cannot be passed successfully with wrong data
format. This is found the data transferring broken on 96boards Hikey.
This patch is to change all parameters to u32 type, and verified on
Hikey board the DT parameters can pass successfully.
[johnyoun: minor rebase]
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Remove DMA memory free from EP disable flow by replacing
dma_alloc_coherent with dmam_alloc_coherent.
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc2_hsotg_ep_enable can be called from interrupt context, so all
allocations should be done with GFP_ATOMIC flags. This fixes following
issue on ARM architecture:
[<c010d830>] (unwind_backtrace) from [<c010a51c>] (show_stack+0x10/0x14)
[<c010a51c>] (show_stack) from [<c032930c>] (dump_stack+0x74/0x94)
[<c032930c>] (dump_stack) from [<c011cd30>] (__warn+0xd4/0x100)
[<c011cd30>] (__warn) from [<c011cd7c>] (warn_slowpath_null+0x20/0x28)
[<c011cd7c>] (warn_slowpath_null) from [<c0187e04>] (smp_call_function_many+0xcc/0x2a4)
[<c0187e04>] (smp_call_function_many) from [<c0188014>] (on_each_cpu_mask+0x38/0xa8)
[<c0188014>] (on_each_cpu_mask) from [<c01ddfe0>] (start_isolate_page_range+0x134/0x1b8)
[<c01ddfe0>] (start_isolate_page_range) from [<c01a3c14>] (alloc_contig_range+0xac/0x2f8)
[<c01a3c14>] (alloc_contig_range) from [<c01de3e4>] (cma_alloc+0xe0/0x1a8)
[<c01de3e4>] (cma_alloc) from [<c0110acc>] (__alloc_from_contiguous+0x38/0xe0)
[<c0110acc>] (__alloc_from_contiguous) from [<c0110ba4>] (cma_allocator_alloc+0x30/0x38)
[<c0110ba4>] (cma_allocator_alloc) from [<c0111034>] (__dma_alloc+0x1c0/0x2c8)
[<c0111034>] (__dma_alloc) from [<c01111b4>] (arm_dma_alloc+0x3c/0x48)
[<c01111b4>] (arm_dma_alloc) from [<c04ad800>] (dwc2_hsotg_ep_enable+0xec/0x46c)
[<c04ad800>] (dwc2_hsotg_ep_enable) from [<c04da610>] (usb_ep_enable+0x2c/0x3c)
[<c04da610>] (usb_ep_enable) from [<c04dc0c0>] (ecm_set_alt+0xa8/0x154)
[<c04dc0c0>] (ecm_set_alt) from [<c04d678c>] (composite_setup+0xd74/0x1540)
[<c04d678c>] (composite_setup) from [<c04ae048>] (dwc2_hsotg_complete_setup+0xb8/0x370)
[<c04ae048>] (dwc2_hsotg_complete_setup) from [<c04d987c>] (usb_gadget_giveback_request+0xc/0x10)
[<c04d987c>] (usb_gadget_giveback_request) from [<c04acafc>] (dwc2_hsotg_complete_request+0x78/0x128)
[<c04acafc>] (dwc2_hsotg_complete_request) from [<c04aed28>] (dwc2_hsotg_epint+0x69c/0x81c)
[<c04aed28>] (dwc2_hsotg_epint) from [<c04af6c4>] (dwc2_hsotg_irq+0xfc/0x748)
[<c04af6c4>] (dwc2_hsotg_irq) from [<c0163264>] (__handle_irq_event_percpu+0x58/0x140)
[<c0163264>] (__handle_irq_event_percpu) from [<c0163368>] (handle_irq_event_percpu+0x1c/0x58)
[<c0163368>] (handle_irq_event_percpu) from [<c01633dc>] (handle_irq_event+0x38/0x5c)
[<c01633dc>] (handle_irq_event) from [<c01666e4>] (handle_fasteoi_irq+0xc4/0x19c)
[<c01666e4>] (handle_fasteoi_irq) from [<c0162a2c>] (generic_handle_irq+0x18/0x28)
[<c0162a2c>] (generic_handle_irq) from [<c0162b40>] (__handle_domain_irq+0x6c/0xe4)
[<c0162b40>] (__handle_domain_irq) from [<c0101470>] (gic_handle_irq+0x50/0x9c)
[<c0101470>] (gic_handle_irq) from [<c010b00c>] (__irq_svc+0x6c/0xa8)
Fixes: 5f54c54b0b ("usb: dwc2: gadget: Add DDMA chain pointers to
dwc2_hsotg_ep structure")
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The current default for gadget DMA descriptor results on bcm2835 in a
unnecessary error message:
Invalid value 1 for param gadget-dma-desc
So fix this by using hw->dma_desc_enable as default value.
Fixes: dec4b55677 ("usb: dwc2: gadget: Add descriptor DMA parameter")
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The current defaults for DMA results on a non-DMA platform in a unnecessary
error message:
Invalid value 0 for param gadget-dma
So fix this by using dma_capable as default value.
Fixes: 9962b62f1b ("usb: dwc2: Deprecate g-use-dma binding")
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
According to the Devicetree ePAPR [1] the datatypes u8 and u16 are
not defined. So using device_property_read_u16() would result in
a partial read of a 32-bit big-endian integer which is not intended.
So we better read the complete 32-bit value. This fixes a regression
on bcm2835 where the values for g-rx-fifo-size and g-np-tx-fifo-size
always read as zero:
Invalid value 0 for param g-rx-fifo-size
Invalid value 0 for param g-np-tx-fifo-size
[1] - http://elinux.org/images/c/cf/Power_ePAPR_APPROVED_v1.1.pdf
Fixes: 05ee799f20 ("usb: dwc2: Move gadget settings into core_params")
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Since commit "usb: dwc2: Improve handling of host and device hwparams" the
host mode specific hardware parameter aren't initialized in peripheral mode
from the register settings anymore. So we better do not set them in this
case which avoids the following warnings on bcm2835:
256 invalid for host_nperio_tx_fifo_size. Check HW configuration.
512 invalid for host_perio_tx_fifo_size. Check HW configuration.
Fixes: 55e1040e42 ("usb: dwc2: Improve handling of host and device hwparams")
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Removed extern specifier from dwc2_host_start(), dwc2_host_disconnect()
and dwc2_host_hub_info() functions. Moved those functions from header
to source. Then make them static.
Signed-off-by: Razmik Karapetyan <razmik@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
NPTXFIFO's start address is showing 0x03000000 instead of 0x00000800.
Replaced val & FIFOSIZE_DEPTH_MASK by val & FIFOSIZE_STARTADDR_MASK in
fifo_show() function.
Signed-off-by: Razmik Karapetyan <razmik@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Remove request length checking from dwc2_hsotg_unmap_dma() and
dwc2_hsotg_map_dma(). That checking is done in functions called from
those functions, usb_gadget_unmap_request_by_dev() and
usb_gadget_map_request_by_dev() respectively, so it's unnecessary.
Signed-off-by: Razmik Karapetyan <razmik@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
While sending zlp for DWC2_EP0_STATUS_IN EP direction was changed to IN.
Change it back to complete OUT transfer request.
This affects only on DMA mode, because DMA buffer map/unmap function is
direction sensitive.
Signed-off-by: Razmik Karapetyan <razmik@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Check the request length in dwc2_hsotg_start_req() function. If
length == 0, do not write DMA address to control register.
Signed-off-by: Razmik Karapetyan <razmik@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Stop sending complete split requests in case of ISOC IN split transfers
after getting data with PID0. Otherwise we will get a NYET for each
additional IN token.
Signed-off-by: Sevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch adds support for the "amcc,usb-otg" device
which is found in the PowerPC Canyonlands' dts.
The device definition was added by:
commit c89b3458d8 ("powerpc/44x: Add USB DWC DTS entry to Canyonlands
board")
but without any driver support as the dwc2 driver wasn't available at
that time.
Note: The system can't use the generic "snps,dwc2" compatible
because of the special ahbcfg configuration. The default
GAHBCFG_HBSTLEN_INCR4 of snps,dwc2 can cause a system hang
when the USB and SATA is used concurrently.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch moves the the host_dma initialization
before dwc2_set_param_dma_desc_enable() and
dwc2_set_param_dma_desc_fs_enable(). The reason being
that both function need it.
Fixes: 1205489cee75bf39 ("usb: dwc2: Get host DMA device properties")
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added new core param for low speed, which can be used only when SNPSID
is equal to DWC2_CORE_FS_IOT. When LS mode is enabled, we are
restricting ep types and providing to upper layer only INTR and CTRL
endpoints.
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When device is enumerated in LS we should program ep0_mps accordingly.
USB2 spec says that in LS mode, control ep mps must be 8.
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add new device IDs for IOT gadget. Done changes in probe to
configure core accordingly depending on device ID value.
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Do modifications in dwc2_hsotg_core_init_disconnected() function to
enable USB 1.1 Full-Speed Serial Transceiver Select in GUSBCFG register
if corresponding speed and PHY types are chosen. Adjust device speed
selection in DCFG register as well.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Check if endpoint is enabled during dwc2_hsotg_ep_disable() function
processing and call dwc2_hsotg_ep_stop_xfr() to disable it and flush
associated FIFO.
Move dwc2_hsotg_ep_stop_xfr() and dwc2_hsotg_wait_bit_set() functions
upper before dwc2_hsotg_ep_enable and dwc2_hsotg_ep_disable function
definitions.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Correct dwc2_hsotg_ep_stop_xfr() function to follow dwc2 programming
guide for setting NAK on specific endpoint, disabling it and flushing
corresponding FIFO.
Current code does not take into account whether core acts in shared or
dedicated FIFO mode, current endpoint is periodic or not. It does not
clear EPDISBLD interrupt after programming of DXEPCTL_EPDIS, does not
flush shared TX FIFO and tries to clear global out NAK in wrong manner
instead of setting DCTL_CGOUTNAK.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Tests with various hosts show that depend on time difference between
host sending SETUP packet and IN/OUT token SW could get Xfercomplete
interrupt without SetUp interrupt. On the other hand, SW should parse
received SETUP packet only after ensuring that Host has moved to either
Data or Status stage of control transfer.
For this purpose added checking in the dwc2_hsotg_epint() function to
not handle xfercomplete and postpone SETUP packet analysis till SW's
getting of setup phase done interrupt.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In DDMA mode if programmed ISOC OUT transfer length is not DWORD
aligned, after closing descriptor HW leaves value of 4 - (ureq->length %
4) in the RX bytes. This is caused because DMA works using 4B chunks.
Example: if length = 9 and all 9 bytes were received from the bus, after
xfercomplete rx_bytes value is 3. Hence add this value to the amount of
transferred bytes.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Enable the BNA (Buffer Not Available) interrupt in descriptor DMA mode.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
For DDMA mode in case of isochronous transfers completion performed
differently than other transfer types. This is because each usb request
was mapped to one descriptor in the chain and SW gets xfercomplete
interrupt on all descriptors. The endpoint remains enabled until HW
processes last descriptor with "L" bit set or BNA interrupt gets
asserted for IN and OUT endpoints correspondingly.
Add function dwc2_gadget_complete_isoc_request_ddma() - completes one
isochronous request taken from endpoint's queue.
Add function dwc2_gadget_start_next_isoc_ddma() - tries to restart
isochronous endpoint if requests are pending. Check for EPENA. If the
endpoint was disabled, try to restart it after programming descriptor
chain prepared by SW earlier, switch SW to fill the other half of chain.
Add function dwc2_gadget_fill_isoc_desc() - initializes DMA descriptor
for isochronous transfer based on the received request data and endpoint
characteristics.
Added function dwc2_gadget_start_isoc_ddma() - prepare DMA chain for
isochronous transfer in DDMA, programs corresponding DMA address to
DEPDMA, enables the endpoint. This function is called once SW decides to
start isochronous IN or OUT transfer depend on reception of NAK or
OUTTknEPdis interrupts indicating first isochronous token arrival from
host.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In DDMA mode incompISOOUT should be masked, similar as Bulk Out -
XferCompl and BNA should be handled. incompISOIN is not valid in DDMA
and is not getting asserted.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Preparing for isochronous transfers support adding in DDMA mode. In DDMA
isochronous transfers are handled differently compared to Slave and BDMA
modes. This is caused by fact that isoc requests contain data for one
frame/microframe. HW descriptor should contain data of one
frame/microframe as well. Hence each DMA descriptor in the chain will
correspond to one usb request.
Decided to divide endpoints descriptor chain to two halves - while one
will be processed by HW, other one will be under SW control. First part
will be passed to HW once ISOC traffic needs to be started. In parallel
to HW's work SW will keep creating new entries in the other half of
chain if new requests arrive in ep_queue routine. This will allow
passing of already pre-prepared descriptors to HW immediately after
endpoint gets disabled. The endpoint should be disabled once HW closes
descriptor with "L" bit set. Afterwards SW will switch to use first part
of chain if more requests are arriving.
Add two members to the dwc2_hsotg_ep structure to be used in isochronous
transfers' handling in DDMA mode:
-isoc_chain_num - indicates which half of EP descriptor chain can be
used by SW to add new queued requests while HW is
processing other half.
-next_desc - index which points to next not yet programmed descriptor in
the half of descriptor chain which is under SW control.
Also add initialization of these fields in function
dwc2_hsotg_ep_enable().
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add DCFG register field macro for descriptor DMA mode and update core
initialization routine to set that bit accordingly.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In DDMA mode of operation IN status phase of control write transfer
should start after getting StsPhseRcvd interrupt. This interrupt is
issued by HW once host starts to send IN tokens after data stage.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The StsPhseRcvd interrupt should not be enabled in slave mode.
Also move the StsPhsRcvd interrupt checking in the endpoint interrupt
handler to the correct order according to the databook. The interrupt
itself will be implemented in a later commit.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Update transfer starting dwc2_hsotg_start_req() routine with call of
function dwc2_gadget_config_nonisoc_xfer_ddma() to fill descriptor
chain.
Add call of dwc2_gadget_get_xfersize_ddma() in
dwc2_hsotg_handle_outdone() and dwc2_hsotg_complete_in() interrupt
handlers for DDMA mode to get information on transferred data from
descriptors instead of DXEPTSIZ.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add dwc2_gadget_set_ep0_desc_chain() function to switch between EP0 DDMA
chains depend on the stage of control transfer.
Include EP0 DDMA chain selection during ep_queue called from
dwc2_hsotg_enqueue_setup() for setup stage. Selecting and filling DDMA
chain for status phase as well - add calls of
dwc2_gadget_set_ep0_desc_chain() and
dwc2_gadget_config_nonisoc_xfer_ddma() functions.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This property was mistakenly added, then removed, so don't read it in.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add DMA descriptor members to the dwc2_hsotg_ep structure.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add dwc2_gadget_get_chain_limit() function and its call in transfer
start routine to correctly estimate one go on transfer size if
descriptor DMA mode is selected.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Rename MAX_DMA_DESC_SIZE to HOST_DMA_NBYTES_LIMIT as it stores value of
host DMA descriptor transfer bytes' limit. Values are different in case
of gadget DMA descriptors.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Update dwc2_hsotg structure to add descriptor chains for EP 0: two DMA
descriptors for Setup phase, per one for IN/OUT data and status phases.
Add their allocation function dwc2_gadget_alloc_ctrl_desc_chains() and
its call during gadget probe.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add device mode DMA transfer descriptor status quadlet field notations.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add a parameter for descriptor DMA and set it based on hardware
capabilities. This won't actually be used by the gadget until later,
when the descriptor DMA code is in place.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Make the DMA descriptor structure packed to guarantee alignment and size
in memory.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Rename DMA descriptor structure from dwc2_hcd_dma_desc to dwc2_dma_desc
as it is applies to both host and gadget.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This is not needed as the gadget now fully supports DMA and it can
autodetect it. This was initially added because gadget DMA mode was only
partially implemented so could not be automatically enabled.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This fixes the coverity issues related to unreachable code with
debugging off.
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Because usb_pipetype() masks urb->pipe, the default case can never be
hit. Remove it. This cleans up a coverity warning.
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Update the dwc2 driver for the new behavior of the usb_endpoint_maxp()
and also use the new usb_endpoint_maxp_mult() helper function.
This commit fixes failures in high-badwith ISOC transfer tests.
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add device parameters handling in dwc2-pci similar what is done in dwc3.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The driver will automatically enable host DMA and use it if available.
This is consistent with the behavior of all existing platforms.
Read in the "snps,host-dma-disable" device property to disable it.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Rename it so that it is more consistent with the gadget dma parameter.
It only affects host-mode operation so prefix it with "host".
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Minas Harutyunyan