commit 3859e85de30815a20bce7db712ce3d94d40a682d upstream.
START BP-850K is a dot matrix printer that crashes when
it receives a Set-Interface request and needs USB_QUIRK_NO_SET_INTF
to work properly.
Cc: stable <stable@kernel.org>
Signed-off-by: jinxiaobo <jinxiaobo@uniontech.com>
Signed-off-by: WangYuli <wangyuli@uniontech.com>
Link: https://lore.kernel.org/r/202E4B2BD0F0FEA4+20240702154408.631201-1-wangyuli@uniontech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5a1ccf0c72cf917ff3ccc131d1bb8d19338ffe52 ]
This patch introduces a new USB quirk,
USB_QUIRK_SHORT_SET_ADDRESS_REQ_TIMEOUT, which modifies the timeout value
for the SET_ADDRESS request. The standard timeout for USB request/command
is 5000 ms, as recommended in the USB 3.2 specification (section 9.2.6.1).
However, certain scenarios, such as connecting devices through an APTIV
hub, can lead to timeout errors when the device enumerates as full speed
initially and later switches to high speed during chirp negotiation.
In such cases, USB analyzer logs reveal that the bus suspends for
5 seconds due to incorrect chirp parsing and resumes only after two
consecutive timeout errors trigger a hub driver reset.
Packet(54) Dir(?) Full Speed J(997.100 us) Idle( 2.850 us)
_______| Time Stamp(28 . 105 910 682)
_______|_____________________________________________________________Ch0
Packet(55) Dir(?) Full Speed J(997.118 us) Idle( 2.850 us)
_______| Time Stamp(28 . 106 910 632)
_______|_____________________________________________________________Ch0
Packet(56) Dir(?) Full Speed J(399.650 us) Idle(222.582 us)
_______| Time Stamp(28 . 107 910 600)
_______|_____________________________________________________________Ch0
Packet(57) Dir Chirp J( 23.955 ms) Idle(115.169 ms)
_______| Time Stamp(28 . 108 532 832)
_______|_____________________________________________________________Ch0
Packet(58) Dir(?) Full Speed J (Suspend)( 5.347 sec) Idle( 5.366 us)
_______| Time Stamp(28 . 247 657 600)
_______|_____________________________________________________________Ch0
This 5-second delay in device enumeration is undesirable, particularly
in automotive applications where quick enumeration is crucial
(ideally within 3 seconds).
The newly introduced quirks provide the flexibility to align with a
3-second time limit, as required in specific contexts like automotive
applications.
By reducing the SET_ADDRESS request timeout to 500 ms, the
system can respond more swiftly to errors, initiate rapid recovery, and
ensure efficient device enumeration. This change is vital for scenarios
where rapid smartphone enumeration and screen projection are essential.
To use the quirk, please write "vendor_id:product_id:p" to
/sys/bus/usb/drivers/hub/module/parameter/quirks
For example,
echo "0x2c48:0x0132:p" > /sys/bus/usb/drivers/hub/module/parameters/quirks"
Signed-off-by: Hardik Gajjar <hgajjar@de.adit-jv.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20231027152029.104363-2-hgajjar@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
The Focusrite Scarlett audio device does not behave correctly during
resumes. Below is what happens during every resume (captured with
Beagle 5000):
<Suspend>
<Resume>
<Reset>/<Chirp J>/<Tiny J>
<Reset/Target disconnected>
<High Speed>
The Scarlett disconnects and is enumerated again.
However from time to time it drops completely off the USB bus during
resume. Below is captured occurrence of such an event:
<Suspend>
<Resume>
<Reset>/<Chirp J>/<Tiny J>
<Reset>/<Chirp K>/<Tiny K>
<High Speed>
<Corrupted packet>
<Reset/Target disconnected>
To fix the condition a user has to unplug and plug the device again.
With USB_QUIRK_RESET_RESUME applied ("usbcore.quirks=1235:8211:b")
for the Scarlett audio device the issue still reproduces.
Applying USB_QUIRK_DISCONNECT_SUSPEND ("usbcore.quirks=1235:8211:m")
fixed the issue and the Scarlett audio device didn't drop off the USB
bus for ~5000 suspend/resume cycles where originally issue reproduced in
~100 or less suspend/resume cycles.
Signed-off-by: Łukasz Bartosik <lb@semihalf.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20230724112911.1802577-1-lb@semihalf.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Alcor Link AK9563 smartcard reader used on some Lenovo platforms
doesn't work. If LPM is enabled the reader will provide an invalid
usb config descriptor. Added quirk to disable LPM.
Verified fix on Lenovo P16 G1 and T14 G3
Tested-by: Miroslav Zatko <mzatko@mirexoft.com>
Tested-by: Dennis Wassenberg <dennis.wassenberg@secunet.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dennis Wassenberg <dennis.wassenberg@secunet.com>
Signed-off-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Link: https://lore.kernel.org/r/20230208181223.1092654-1-mpearson-lenovo@squebb.ca
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before adding this quirk, this (mechanical keyboard) device would not be
recognized, logging:
new full-speed USB device number 56 using xhci_hcd
unable to read config index 0 descriptor/start: -32
chopping to 0 config(s)
It would take dozens of plugging/unpuggling cycles for the keyboard to
be recognized. Keyboard seems to simply work after applying this quirk.
This issue had been reported by users in two places already ([1], [2])
but nobody tried upstreaming a patch yet. After testing I believe their
suggested fix (DELAY_INIT + NO_LPM + DEVICE_QUALIFIER) was probably a
little overkill. I assume this particular combination was tested because
it had been previously suggested in [3], but only NO_LPM seems
sufficient for this device.
[1]: https://qiita.com/float168/items/fed43d540c8e2201b543
[2]: https://blog.kostic.dev/posts/making-the-realforce-87ub-work-with-usb30-on-Ubuntu/
[3]: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1678477
Cc: stable@vger.kernel.org
Signed-off-by: Nicolas Dumazet <ndumazet@google.com>
Link: https://lore.kernel.org/r/20221109122946.706036-1-ndumazet@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Lenovo OneLink+ Dock contains two VL812 USB3.0 controllers:
17ef:1018 upstream
17ef:1019 downstream
These hubs suffer from two separate problems:
1) After the host system was suspended and woken up, the hubs appear to
be in a random state. Some downstream ports (both internal to the
built-in audio and network controllers, and external to USB sockets)
may no longer be functional. The exact list of disabled ports (if
any) changes from wakeup to wakeup. Ports remain in that state until
the dock is power-cycled, or until the laptop is rebooted.
Wakeup sources connected to the hubs (keyboard, WoL on the integrated
gigabit controller) will wake the system up from suspend, but they
may no longer work after wakeup (and in that case will no longer work
as wakeup source in a subsequent suspend-wakeup cycle).
This issue appears in the logs with messages such as:
usb 1-6.1-port4: cannot disable (err = -71)
usb 1-6-port2: cannot disable (err = -71)
usb 1-6.1: clear tt 1 (80c0) error -71
usb 1-6-port4: cannot disable (err = -71)
usb 1-6.4: PM: dpm_run_callback(): usb_dev_resume+0x0/0x10 [usbcore] returns -71
usb 1-6.4: PM: failed to resume async: error -71
usb 1-7: reset full-speed USB device number 5 using xhci_hcd
usb 1-6.1-port1: cannot reset (err = -71)
usb 1-6.1-port1: cannot reset (err = -71)
usb 1-6.1-port1: cannot reset (err = -71)
usb 1-6.1-port1: cannot reset (err = -71)
usb 1-6.1-port1: cannot reset (err = -71)
usb 1-6.1-port1: Cannot enable. Maybe the USB cable is bad?
usb 1-6.1-port1: cannot disable (err = -71)
usb 1-6.1-port1: cannot reset (err = -71)
usb 1-6.1-port1: cannot reset (err = -71)
usb 1-6.1-port1: cannot reset (err = -71)
usb 1-6.1-port1: cannot reset (err = -71)
usb 1-6.1-port1: cannot reset (err = -71)
usb 1-6.1-port1: Cannot enable. Maybe the USB cable is bad?
usb 1-6.1-port1: cannot disable (err = -71)
2) Some USB devices cannot be enumerated properly. So far I have only
seen the issue with USB 3.0 devices. The same devices work without
problem directly connected to the host system, to other systems or to
other hubs (even when those hubs are connected to the OneLink+ dock).
One very reliable reproducer is this USB 3.0 HDD enclosure:
152d:9561 JMicron Technology Corp. / JMicron USA Technology Corp. Mobius
I have seen it happen sporadically with other USB 3.0 enclosures,
with controllers from different manufacturers, all self-powered.
Typical messages in the logs:
xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
usb 2-1.4: device not accepting address 6, error -62
xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
usb 2-1.4: device not accepting address 7, error -62
usb 2-1-port4: attempt power cycle
xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
usb 2-1.4: device not accepting address 8, error -62
xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
usb 2-1.4: device not accepting address 9, error -62
usb 2-1-port4: unable to enumerate USB device
Through trial and error, I found that the USB_QUIRK_RESET_RESUME solved
the second issue. Further testing then uncovered the first issue. Test
results are summarized in this table:
=======================================================================================
Settings USB2 hotplug USB3 hotplug State after waking up
---------------------------------------------------------------------------------------
power/control=auto works fails broken
usbcore.autosuspend=-1 works works broken
OR power/control=on
power/control=auto works (1) works (1) works
and USB_QUIRK_RESET_RESUME
power/control=on works works works
and USB_QUIRK_RESET_RESUME
HUB_QUIRK_DISABLE_AUTOSUSPEND works works works
and USB_QUIRK_RESET_RESUME
=======================================================================================
In those results, the power/control settings are applied to both hubs,
both on the USB2 and USB3 side, before each test.
From those results, USB_QUIRK_RESET_RESUME is required to reset the hubs
properly after a suspend-wakeup cycle, and the hubs must not autosuspend
to work around the USB3 issue.
A secondary effect of USB_QUIRK_RESET_RESUME is to prevent the hubs'
upstream links from suspending (the downstream ports can still suspend).
This secondary effect is used in results (1). It is enough to solve the
USB3 problem.
Setting USB_QUIRK_RESET_RESUME on those hubs is the smallest patch that
solves both issues.
Prior to creating this patch, I have used the USB_QUIRK_RESET_RESUME via
the kernel command line for over a year without noticing any side
effect.
Thanks to Oliver Neukum @Suse for explanations of the operations of
USB_QUIRK_RESET_RESUME, and requesting more testing.
Signed-off-by: Jean-Francois Le Fillatre <jflf_kernel@gmx.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20220927073407.5672-1-jflf_kernel@gmx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add USB_QUIRK_NO_LPM and USB_QUIRK_RESET_RESUME quirks for Dell usb gen
2 device to not fail during enumeration.
Found this bug on own testing
Signed-off-by: Monish Kumar R <monish.kumar.r@intel.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220520130044.17303-1-monish.kumar.r@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This has been reported to stall if queried
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20220414123152.1700-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This device is reported to stall when enummerated.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20220414110209.30924-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This device doesn't work well with LPM, losing connectivity intermittently.
Disable LPM to resolve the issue.
Reviewed-by: <markpearson@lenovo.com>
Signed-off-by: Jimmy Wang <wangjm221@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211214012652.4898-1-wangjm221@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is another branded 8153 device that doesn't work well with LPM:
r8152 2-2.1:1.0 enp0s13f0u2u1: Stop submitting intr, status -71
Disable LPM to resolve the issue.
Signed-off-by: Ole Ernst <olebowle@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 0bd860493f.
While the patch was working as stated,ie preventing the L850-GL LTE modem
from crashing on some U3 wake-ups due to a race condition between the
host wake-up and the modem-side wake-up, when using the MBIM interface,
this would force disabling the USB runtime PM on the device.
The increased power consumption is significant for LTE laptops,
and given that with decently recent modem firmwares, when the modem hits
the bug, it automatically recovers (ie it drops from the bus, but
automatically re-enumerates after less than half a second, rather than being
stuck until a power cycle as it was doing with ancient firmware), for
most people, the trade-off now seems in favor of re-enabling it by
default.
For people with access to the platform code, the bug can also be worked-around
successfully by changing the USB3 LFPM polling off-time for the XHCI
controller in the BIOS code.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Link: https://lore.kernel.org/r/20210721092516.2775971-1-vpalatin@chromium.org
Fixes: 0bd860493f ("USB: quirks: ignore remote wake-up on Fibocom L850-GL LTE modem")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit ca91fd8c76 ("USB: Add reset-resume quirk for
WD19's Realtek Hub"). The previous patch in the series now handles
the problematic hubs by checking the port status and handling it
accordingly when PORT_SUSPEND timeout occurs. We don't need to use
reset-resume all the time.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Chris Chiu <chris.chiu@canonical.com>
Link: https://lore.kernel.org/r/20210514045405.5261-3-chris.chiu@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Realtek Hub (0bda:5487) in Dell Dock WD19 sometimes fails to work
after the system resumes from suspend with remote wakeup enabled
device connected:
[ 1947.640907] hub 5-2.3:1.0: hub_ext_port_status failed (err = -71)
[ 1947.641208] usb 5-2.3-port5: cannot disable (err = -71)
[ 1947.641401] hub 5-2.3:1.0: hub_ext_port_status failed (err = -71)
[ 1947.641450] usb 5-2.3-port4: cannot reset (err = -71)
Information of this hub:
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 10 Spd=480 MxCh= 5
D: Ver= 2.10 Cls=09(hub ) Sub=00 Prot=02 MxPS=64 #Cfgs= 1
P: Vendor=0bda ProdID=5487 Rev= 1.47
S: Manufacturer=Dell Inc.
S: Product=Dell dock
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=01 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 1 Ivl=256ms
I:* If#= 0 Alt= 1 #EPs= 1 Cls=09(hub ) Sub=00 Prot=02 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 1 Ivl=256ms
The failure results from the ETIMEDOUT by chance when turning on
the suspend feature for the specified port of the hub. The port
seems to be in an unknown state so the hub_activate during resume
fails the hub_port_status, then the hub will fail to work.
The quirky hub needs the reset-resume quirk to function correctly.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Chris Chiu <chris.chiu@canonical.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210420174651.6202-1-chris.chiu@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is another branded 8153 device that doesn't work well with LPM
enabled:
[ 400.597506] r8152 5-1.1:1.0 enx482ae3a2a6f0: Tx status -71
So disable LPM to resolve the issue.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/1922651
Link: https://lore.kernel.org/r/20210412135455.791971-1-kai.heng.feng@canonical.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This LTE modem (M.2 card) has a bug in its power management:
there is some kind of race condition for U3 wake-up between the host and
the device. The modem firmware sometimes crashes/locks when both events
happen at the same time and the modem fully drops off the USB bus (and
sometimes re-enumerates, sometimes just gets stuck until the next
reboot).
Tested with the modem wired to the XHCI controller on an AMD 3015Ce
platform. Without the patch, the modem dropped of the USB bus 5 times in
3 days. With the quirk, it stayed connected for a week while the
'runtime_suspended_time' counter incremented as excepted.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Link: https://lore.kernel.org/r/20210319124802.2315195-1-vpalatin@chromium.org
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without this quirk starting a video capture from the device often fails with
kernel: uvcvideo: Failed to set UVC probe control : -110 (exp. 34).
Signed-off-by: Stefan Ursella <stefan.ursella@wolfvision.net>
Link: https://lore.kernel.org/r/20210210140713.18711-1-stefan.ursella@wolfvision.net
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I got reports that some models of this old scanner need
this when using runtime PM.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201207130323.23857-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 3e4f8e21c4 ("USB: core: fix check for duplicate endpoints")
aimed to make the USB stack more reliable by detecting and skipping
over endpoints that are duplicated between interfaces. This caused a
regression for a Hercules audio card (reported as Bugzilla #208357),
which contains such non-compliant duplications. Although the
duplications are harmless, skipping the valid endpoints prevented the
device from working.
This patch fixes the regression by adding ENDPOINT_IGNORE quirks for
the Hercules card, telling the kernel to ignore the invalid duplicate
endpoints and thereby allowing the valid endpoints to be used as
intended.
Fixes: 3e4f8e21c4 ("USB: core: fix check for duplicate endpoints")
CC: <stable@vger.kernel.org>
Reported-by: Alexander Chalikiopoulos <bugzilla.kernel.org@mrtoasted.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20201119170040.GA576844@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a USB_QUIRK_DISCONNECT_SUSPEND quirk for the Lenovo TIO built-in
usb-audio. when A630Z going into S3,the system immediately wakeup 7-8
seconds later by usb-audio disconnect interrupt to avoids the issue.
eg dmesg:
....
[ 626.974091 ] usb 7-1.1: USB disconnect, device number 3
....
....
[ 1774.486691] usb 7-1.1: new full-speed USB device number 5 using xhci_hcd
[ 1774.947742] usb 7-1.1: New USB device found, idVendor=17ef, idProduct=a012, bcdDevice= 0.55
[ 1774.956588] usb 7-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1774.964339] usb 7-1.1: Product: Thinkcentre TIO24Gen3 for USB-audio
[ 1774.970999] usb 7-1.1: Manufacturer: Lenovo
[ 1774.975447] usb 7-1.1: SerialNumber: 000000000000
[ 1775.048590] usb 7-1.1: 2:1: cannot get freq at ep 0x1
.......
Seeking a better fix, we've tried a lot of things, including:
- Check that the device's power/wakeup is disabled
- Check that remote wakeup is off at the USB level
- All the quirks in drivers/usb/core/quirks.c
e.g. USB_QUIRK_RESET_RESUME,
USB_QUIRK_RESET,
USB_QUIRK_IGNORE_REMOTE_WAKEUP,
USB_QUIRK_NO_LPM.
but none of that makes any difference.
There are no errors in the logs showing any suspend/resume-related issues.
When the system wakes up due to the modem, log-wise it appears to be a
normal resume.
Introduce a quirk to disable the port during suspend when the modem is
detected.
Signed-off-by: penghao <penghao@uniontech.com>
Link: https://lore.kernel.org/r/20201118123039.11696-1-penghao@uniontech.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In Bugzilla #208257, Julien Humbert reports that a 32-GB Kingston
flash drive spontaneously disconnects and reconnects, over and over.
Testing revealed that disabling Link Power Management for the drive
fixed the problem.
This patch adds a quirk entry for that drive to turn off LPM permanently.
CC: Hans de Goede <jwrdegoede@fedoraproject.org>
CC: <stable@vger.kernel.org>
Reported-and-tested-by: Julien Humbert <julroy67@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20201102145821.GA1478741@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a USB_QUIRK_IGNORE_REMOTE_WAKEUP quirk for the BYD zhaoxin notebook.
This notebook come with usb touchpad. And we would like to disable
touchpad wakeup on this notebook by default.
Signed-off-by: Penghao <penghao@uniontech.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200907023026.28189-1-penghao@uniontech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Sound Devices MixPre-D audio card suffers from the same defect
as the Sound Devices USBPre2: an endpoint shared between a normal
audio interface and a vendor-specific interface, in violation of the
USB spec. Since the USB core now treats duplicated endpoints as bugs
and ignores them, the audio endpoint isn't available and the card
can't be used for audio capture.
Along the same lines as commit bdd1b147b8 ("USB: quirks: blacklist
duplicate ep on Sound Devices USBPre2"), this patch adds a quirks
entry saying to ignore ep5in for interface 1, leaving it available for
use with standard audio interface 2.
Reported-and-tested-by: Jean-Christophe Barnoud <jcbarnoud@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Fixes: 3e4f8e21c4 ("USB: core: fix check for duplicate endpoints")
Link: https://lore.kernel.org/r/20200826194624.GA412633@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function quirks_param_set() takes as argument a const char* pointer
to the new value of the usbcore.quirks parameter. It then casts this
pointer to a non-const char* pointer and passes it to the strsep()
function, which overwrites the value.
Fix this by creating a copy of the value using kstrdup() and letting
that copy be written to by strsep().
Fixes: 027bd6cafd ("usb: core: Add "quirks" parameter for usbcore")
Signed-off-by: Kars Mulder <kerneldev@karsmulder.nl>
Link: https://lore.kernel.org/r/5ee2-5f048a00-21-618c5c00@230659773
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB core has a quirk flag to ignore specific endpoints, so rename it
to be more obvious what this quirk does.
Cc: Johan Hovold <johan@kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Richard Dodd <richard.o.dodd@gmail.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jonathan Cox <jonathan@jdcox.net>
Cc: Bastien Nocera <hadess@hadess.net>
Cc: "Thiébaud Weksteen" <tweek@google.com>
Cc: Nishad Kamdar <nishadkamdar@gmail.com>
Link: https://lore.kernel.org/r/20200618094300.1887727-2-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Logitech C922, just like other Logitech webcams,
needs the USB_QUIRK_DELAY_INIT or it will randomly
not respond after device connection
Signed-off-by: Tomasz Meresiński <tomasz@meresinski.eu>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200603203347.7792-1-tomasz@meresinski.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Corsair K70 RGB RAPIDFIRE needs the USB_QUIRK_DELAY_INIT and
USB_QUIRK_DELAY_CTRL_MSG to function or it will randomly not
respond on boot, just like other Corsair keyboards
Signed-off-by: Jonathan Cox <jonathan@jdcox.net>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200410212427.2886-1-jonathan@jdcox.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have been receiving bug reports that ethernet connections over
RTL8153 based ethernet adapters stops working after a while with
errors like these showing up in dmesg when the ethernet stops working:
[12696.189484] r8152 6-1:1.0 enp10s0u1: Tx timeout
[12702.333456] r8152 6-1:1.0 enp10s0u1: Tx timeout
[12707.965422] r8152 6-1:1.0 enp10s0u1: Tx timeout
This has been reported on Dell WD15 docks, Belkin USB-C Express Dock 3.1
docks and with generic USB to ethernet dongles using the RTL8153
chipsets. Some users have tried adding usbcore.quirks=0bda:8153:k to
the kernel commandline and all users who have tried this report that
this fixes this.
Also note that we already have an existing NO_LPM quirk for the RTL8153
used in the Microsoft Surface Dock (where it uses a different usb-id).
This commit adds a NO_LPM quirk for the generic Realtek RTL8153
0bda:8153 usb-id, fixing the Tx timeout errors on these devices.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=198931
Cc: stable@vger.kernel.org
Cc: russianneuromancer@ya.ru
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200313120708.100339-1-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Realtek Hub (0bda:0x0487) used in Dell Dock WD19 sometimes drops off the
bus when bringing underlying ports from U3 to U0.
Disabling LPM on the hub during setting link state is not enough, so
let's disable LPM completely for this hub.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200205112633.25995-3-kai.heng.feng@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
LPM on the device appears to cause xHCI host controllers to claim
that there isn't enough bandwidth to support additional devices.
Signed-off-by: Dan Lazewatsky <dlaz@chromium.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.com>
Link: https://lore.kernel.org/r/20200226143438.1445-1-gustavo.padovan@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the SourceControl will stay in power-down mode after resuming
from suspend. This patch resets the device after suspend to power it up.
Signed-off-by: Richard Dodd <richard.o.dodd@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200212142220.36892-1-richard.o.dodd@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a new device quirk that can be used to blacklist endpoints.
Since commit 3e4f8e21c4 ("USB: core: fix check for duplicate
endpoints") USB core ignores any duplicate endpoints found during
descriptor parsing.
In order to handle devices where the first interfaces with duplicate
endpoints are the ones that should have their endpoints ignored, we need
to add a blacklist.
Tested-by: edes <edes@gmx.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20200203153830.26394-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the chipmunk-like voice that manifets randomly when
using the integrated mic of the Logitech Webcam HD C270.
The issue was solved initially for this device by commit 2394d67e44
("USB: add RESET_RESUME for webcams shown to be quirky") but it was then
reintroduced by e387ef5c47 ("usb: Add USB_QUIRK_RESET_RESUME for all
Logitech UVC webcams"). This patch is to have the fix back.
Signed-off-by: Marco Zatta <marco@zatta.me>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without USB_QUIRK_NO_LPM ethernet will not work and rtl8152 will
complain with
r8152 <device...>: Stop submitting intr, status -71
Adding the quirk resolves this. As the dock is externally powered, this
should not have any drawbacks.
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To match the Corsair Strafe RGB, the Corsair K70 RGB also requires
USB_QUIRK_DELAY_CTRL_MSG to completely resolve boot connection issues
discussed here: https://github.com/ckb-next/ckb-next/issues/42.
Otherwise roughly 1 in 10 boots the keyboard will fail to be detected.
Patch that applied delay control quirk for Corsair Strafe RGB:
cb88a05887 ("usb: quirks: add control message delay for 1b1c:1b20")
Previous K70 RGB patch to add delay-init quirk:
7a1646d922 ("Add delay-init quirk for Corsair K70 RGB keyboards")
Signed-off-by: Jack Stocker <jackstocker.93@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some lower volume SanDisk Ultra Flair in 16GB, which the VID:PID is
in 0781:5591, will aggressively request LPM of U1/U2 during runtime,
when using this thumb drive as the OS installation key we found the
device will generate failure during U1 exit path making it dropped
from the USB bus, this causes a corrupted installation in system at
the end.
i.e.,
[ 166.918296] hub 2-0:1.0: state 7 ports 7 chg 0000 evt 0004
[ 166.918327] usb usb2-port2: link state change
[ 166.918337] usb usb2-port2: do warm reset
[ 166.970039] usb usb2-port2: not warm reset yet, waiting 50ms
[ 167.022040] usb usb2-port2: not warm reset yet, waiting 200ms
[ 167.276043] usb usb2-port2: status 02c0, change 0041, 5.0 Gb/s
[ 167.276050] usb 2-2: USB disconnect, device number 2
[ 167.276058] usb 2-2: unregistering device
[ 167.276060] usb 2-2: unregistering interface 2-2:1.0
[ 167.276170] xhci_hcd 0000:00:15.0: shutdown urb ffffa3c7cc695cc0 ep1in-bulk
[ 167.284055] sd 0:0:0:0: [sda] tag#0 FAILED Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[ 167.284064] sd 0:0:0:0: [sda] tag#0 CDB: Read(10) 28 00 00 33 04 90 00 01 00 00
...
Analyzed the USB trace in the link layer we realized it is because
of the 6-ms timer of tRecoveryConfigurationTimeout which documented
on the USB 3.2 Revision 1.0, the section 7.5.10.4.2 of "Exit from
Recovery.Configuration"; device initiates U1 exit -> Recovery.Active
-> Recovery.Configuration, then the host timer timeout makes the link
transits to eSS.Inactive -> Rx.Detect follows by a Warm Reset.
Interestingly, the other higher volume of SanDisk Ultra Flair sharing
the same VID:PID, such as 64GB, would not request LPM during runtime,
it sticks at U0 always, thus disabling LPM does not affect those thumb
drives at all.
The same odd occures in SanDisk Ultra Fit 16GB, VID:PID in 0781:5583.
Signed-off-by: Harry Pan <harry.pan@intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cherry G230 Stream 2.0 (G85-231) and 3.0 (G85-232) need this quirk to
function correctly. This fixes a but where double pressing numlock locks
up the device completely with need to replug the keyboard.
Signed-off-by: Michael Niewöhner <linux@mniewoehner.de>
Tested-by: Michael Niewöhner <linux@mniewoehner.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Raydium USB touchscreen fails to set config if LPM is enabled:
[ 2.030658] usb 1-8: New USB device found, idVendor=2386, idProduct=3119
[ 2.030659] usb 1-8: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 2.030660] usb 1-8: Product: Raydium Touch System
[ 2.030661] usb 1-8: Manufacturer: Raydium Corporation
[ 7.132209] usb 1-8: can't set config #1, error -110
Same behavior can be observed on 2386:3114.
Raydium claims the touchscreen supports LPM under Windows, so I used
Microsoft USB Test Tools (MUTT) [1] to check its LPM status. MUTT shows
that the LPM doesn't work under Windows, either. So let's just disable LPM
for Raydium touchscreens.
[1] https://docs.microsoft.com/en-us/windows-hardware/drivers/usbcon/usb-test-tools
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Following on from this patch: https://lkml.org/lkml/2017/11/3/516,
Corsair K70 LUX RGB keyboards also require the DELAY_INIT quirk to
start correctly at boot.
Dmesg output:
usb 1-6: string descriptor 0 read error: -110
usb 1-6: New USB device found, idVendor=1b1c, idProduct=1b33
usb 1-6: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-6: can't set config #1, error -110
Signed-off-by: Emmanuel Pescosta <emmanuelpescosta099@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Devices connected under Terminus Technology Inc. Hub (1a40:0101) may
fail to work after the system resumes from suspend:
[ 206.063325] usb 3-2.4: reset full-speed USB device number 4 using xhci_hcd
[ 206.143691] usb 3-2.4: device descriptor read/64, error -32
[ 206.351671] usb 3-2.4: device descriptor read/64, error -32
Info for this hub:
T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=480 MxCh= 4
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1a40 ProdID=0101 Rev=01.11
S: Product=USB 2.0 Hub
C: #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
Some expirements indicate that the USB devices connected to the hub are
innocent, it's the hub itself is to blame. The hub needs extra delay
time after it resets its port.
Hence wait for extra delay, if the device is connected to this quirky
hub.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Applying dynamic usbcore quirks in early booting when the slab is
not yet ready would cause kernel panic of null pointer dereference
because the quirk_count has been counted as 1 while the quirk_list
was failed to allocate.
i.e.,
[ 1.044970] BUG: unable to handle kernel NULL pointer dereference at (null)
[ 1.044995] IP: [<ffffffffb0953ec7>] usb_detect_quirks+0x88/0xd1
[ 1.045016] PGD 0
[ 1.045026] Oops: 0000 [#1] PREEMPT SMP
[ 1.046986] gsmi: Log Shutdown Reason 0x03
[ 1.046995] Modules linked in:
[ 1.047008] CPU: 0 PID: 81 Comm: kworker/0:3 Not tainted 4.4.154 #28
[ 1.047016] Hardware name: Google Coral/Coral, BIOS Google_Coral.10068.27.0 12/04/2017
[ 1.047028] Workqueue: usb_hub_wq hub_event
[ 1.047037] task: ffff88017a321c80 task.stack: ffff88017a384000
[ 1.047044] RIP: 0010:[<ffffffffb0953ec7>] [<ffffffffb0953ec7>] usb_detect_quirks+0x88/0xd1
To tackle this odd, let's balance the quirk_count to 0 when the kcalloc
call fails, and defer the quirk setting into a lower level callback
which ensures that the kernel memory management has been initialized.
Fixes: 027bd6cafd ("usb: core: Add "quirks" parameter for usbcore")
Signed-off-by: Harry Pan <harry.pan@intel.com>
Acked-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This device does not correctly handle the LPM operations.
Also, the device cannot handle ATA pass-through commands
and locks up when attempted while running in super speed.
This patch adds the equivalent quirk logic as found in uas.
Signed-off-by: Tim Anderson <tsa@biglakesoftware.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
WORLDE Controller KS49 or Prodipe MIDI 49C USB controller
cause a -EPROTO error, a communication restart and loop again.
This issue has already been fixed for KS25.
https://lore.kernel.org/patchwork/patch/753077/
I just add device 201 for KS49 in quirks.c to get it works.
Signed-off-by: Laurent Roux <xpros64@hotmail.fr>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Corsair Strafe appears to suffer from the same issues
as the Corsair Strafe RGB.
Apply the same quirks (control message delay and init delay)
that the RGB version has to 1b1c:1b15.
With these quirks in place the keyboard works correctly upon
booting the system, and no longer requires reattaching the device.
Signed-off-by: Nico Sneck <snecknico@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add DELAY_INIT quirk to fix the following problem with HP
v222w 16GB Mini:
usb 1-3: unable to read config index 0 descriptor/start: -110
usb 1-3: can't read configurations, error -110
usb 1-3: can't set config #1, error -110
Signed-off-by: Kamil Lulko <kamilx.lulko@intel.com>
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
WangYuli
Hardik Gajjar