Fix typos in drivers/pci. Comment and whitespace changes only.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Drivers may rely on pci_disable_link_state() having disabled certain
ASPM link states. If OS can't control ASPM then pci_disable_link_state()
turns into a no-op w/o informing the caller. The driver therefore may
falsely assume the respective ASPM link states are disabled.
Let pci_disable_link_state() propagate errors to the caller, enabling
the caller to react accordingly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently Linux does not follow PCIe spec regarding the required delays
after reset. A concrete example is a Thunderbolt add-in-card that
consists of a PCIe switch and two PCIe endpoints:
+-1b.0-[01-6b]----00.0-[02-6b]--+-00.0-[03]----00.0 TBT controller
+-01.0-[04-36]-- DS hotplug port
+-02.0-[37]----00.0 xHCI controller
\-04.0-[38-6b]-- DS hotplug port
The root port (1b.0) and the PCIe switch downstream ports are all PCIe
gen3 so they support 8GT/s link speeds.
We wait for the PCIe hierarchy to enter D3cold (runtime):
pcieport 0000:00:1b.0: power state changed by ACPI to D3cold
When it wakes up from D3cold, according to the PCIe 4.0 section 5.8 the
PCIe switch is put to reset and its power is re-applied. This means that
we must follow the rules in PCIe 4.0 section 6.6.1.
For the PCIe gen3 ports we are dealing with here, the following applies:
With a Downstream Port that supports Link speeds greater than 5.0
GT/s, software must wait a minimum of 100 ms after Link training
completes before sending a Configuration Request to the device
immediately below that Port. Software can determine when Link training
completes by polling the Data Link Layer Link Active bit or by setting
up an associated interrupt (see Section 6.7.3.3).
Translating this into the above topology we would need to do this (DLLLA
stands for Data Link Layer Link Active):
pcieport 0000:00:1b.0: wait for 100ms after DLLLA is set before access to 0000:01:00.0
pcieport 0000:02:00.0: wait for 100ms after DLLLA is set before access to 0000:03:00.0
pcieport 0000:02:02.0: wait for 100ms after DLLLA is set before access to 0000:37:00.0
I've instrumented the kernel with additional logging so we can see the
actual delays the kernel performs:
pcieport 0000:00:1b.0: power state changed by ACPI to D0
pcieport 0000:00:1b.0: waiting for D3cold delay of 100 ms
pcieport 0000:00:1b.0: waking up bus
pcieport 0000:00:1b.0: waiting for D3hot delay of 10 ms
pcieport 0000:00:1b.0: restoring config space at offset 0x2c (was 0x60, writing 0x60)
...
pcieport 0000:00:1b.0: PME# disabled
pcieport 0000:01:00.0: restoring config space at offset 0x3c (was 0x1ff, writing 0x201ff)
...
pcieport 0000:01:00.0: PME# disabled
pcieport 0000:02:00.0: restoring config space at offset 0x3c (was 0x1ff, writing 0x201ff)
...
pcieport 0000:02:00.0: PME# disabled
pcieport 0000:02:01.0: restoring config space at offset 0x3c (was 0x1ff, writing 0x201ff)
...
pcieport 0000:02:01.0: restoring config space at offset 0x4 (was 0x100000, writing 0x100407)
pcieport 0000:02:01.0: PME# disabled
pcieport 0000:02:02.0: restoring config space at offset 0x3c (was 0x1ff, writing 0x201ff)
...
pcieport 0000:02:02.0: PME# disabled
pcieport 0000:02:04.0: restoring config space at offset 0x3c (was 0x1ff, writing 0x201ff)
...
pcieport 0000:02:04.0: PME# disabled
pcieport 0000:02:01.0: PME# enabled
pcieport 0000:02:01.0: waiting for D3hot delay of 10 ms
pcieport 0000:02:04.0: PME# enabled
pcieport 0000:02:04.0: waiting for D3hot delay of 10 ms
thunderbolt 0000:03:00.0: restoring config space at offset 0x14 (was 0x0, writing 0x8a040000)
...
thunderbolt 0000:03:00.0: PME# disabled
xhci_hcd 0000:37:00.0: restoring config space at offset 0x10 (was 0x0, writing 0x73f00000)
...
xhci_hcd 0000:37:00.0: PME# disabled
For the switch upstream port (01:00.0) we wait for 100ms but not taking
into account the DLLLA requirement. We then wait 10ms for D3hot -> D0
transition of the root port and the two downstream hotplug ports. This
means that we deviate from what the spec requires.
Performing the same check for system sleep (s2idle) transitions we can
see following when resuming from s2idle:
pcieport 0000:00:1b.0: power state changed by ACPI to D0
pcieport 0000:00:1b.0: restoring config space at offset 0x2c (was 0x60, writing 0x60)
...
pcieport 0000:01:00.0: restoring config space at offset 0x3c (was 0x1ff, writing 0x201ff)
...
pcieport 0000:02:02.0: restoring config space at offset 0x3c (was 0x1ff, writing 0x201ff)
pcieport 0000:02:02.0: restoring config space at offset 0x2c (was 0x0, writing 0x0)
pcieport 0000:02:01.0: restoring config space at offset 0x3c (was 0x1ff, writing 0x201ff)
pcieport 0000:02:04.0: restoring config space at offset 0x3c (was 0x1ff, writing 0x201ff)
pcieport 0000:02:02.0: restoring config space at offset 0x28 (was 0x0, writing 0x0)
pcieport 0000:02:00.0: restoring config space at offset 0x3c (was 0x1ff, writing 0x201ff)
pcieport 0000:02:02.0: restoring config space at offset 0x24 (was 0x10001, writing 0x1fff1)
pcieport 0000:02:01.0: restoring config space at offset 0x2c (was 0x0, writing 0x60)
pcieport 0000:02:02.0: restoring config space at offset 0x20 (was 0x0, writing 0x73f073f0)
pcieport 0000:02:04.0: restoring config space at offset 0x2c (was 0x0, writing 0x60)
pcieport 0000:02:01.0: restoring config space at offset 0x28 (was 0x0, writing 0x60)
pcieport 0000:02:00.0: restoring config space at offset 0x2c (was 0x0, writing 0x0)
pcieport 0000:02:02.0: restoring config space at offset 0x1c (was 0x101, writing 0x1f1)
pcieport 0000:02:04.0: restoring config space at offset 0x28 (was 0x0, writing 0x60)
pcieport 0000:02:01.0: restoring config space at offset 0x24 (was 0x10001, writing 0x1ff10001)
pcieport 0000:02:00.0: restoring config space at offset 0x28 (was 0x0, writing 0x0)
pcieport 0000:02:02.0: restoring config space at offset 0x18 (was 0x0, writing 0x373702)
pcieport 0000:02:04.0: restoring config space at offset 0x24 (was 0x10001, writing 0x49f12001)
pcieport 0000:02:01.0: restoring config space at offset 0x20 (was 0x0, writing 0x73e05c00)
pcieport 0000:02:00.0: restoring config space at offset 0x24 (was 0x10001, writing 0x1fff1)
pcieport 0000:02:04.0: restoring config space at offset 0x20 (was 0x0, writing 0x89f07400)
pcieport 0000:02:01.0: restoring config space at offset 0x1c (was 0x101, writing 0x5151)
pcieport 0000:02:00.0: restoring config space at offset 0x20 (was 0x0, writing 0x8a008a00)
pcieport 0000:02:02.0: restoring config space at offset 0xc (was 0x10000, writing 0x10020)
pcieport 0000:02:04.0: restoring config space at offset 0x1c (was 0x101, writing 0x6161)
pcieport 0000:02:01.0: restoring config space at offset 0x18 (was 0x0, writing 0x360402)
pcieport 0000:02:00.0: restoring config space at offset 0x1c (was 0x101, writing 0x1f1)
pcieport 0000:02:04.0: restoring config space at offset 0x18 (was 0x0, writing 0x6b3802)
pcieport 0000:02:02.0: restoring config space at offset 0x4 (was 0x100000, writing 0x100407)
pcieport 0000:02:00.0: restoring config space at offset 0x18 (was 0x0, writing 0x30302)
pcieport 0000:02:01.0: restoring config space at offset 0xc (was 0x10000, writing 0x10020)
pcieport 0000:02:04.0: restoring config space at offset 0xc (was 0x10000, writing 0x10020)
pcieport 0000:02:00.0: restoring config space at offset 0xc (was 0x10000, writing 0x10020)
pcieport 0000:02:01.0: restoring config space at offset 0x4 (was 0x100000, writing 0x100407)
pcieport 0000:02:04.0: restoring config space at offset 0x4 (was 0x100000, writing 0x100407)
pcieport 0000:02:00.0: restoring config space at offset 0x4 (was 0x100000, writing 0x100407)
xhci_hcd 0000:37:00.0: restoring config space at offset 0x10 (was 0x0, writing 0x73f00000)
...
thunderbolt 0000:03:00.0: restoring config space at offset 0x14 (was 0x0, writing 0x8a040000)
This is even worse. None of the mandatory delays are performed. If this
would be S3 instead of s2idle then according to PCI FW spec 3.2 section
4.6.8. there is a specific _DSM that allows the OS to skip the delays
but this platform does not provide the _DSM and does not go to S3 anyway
so no firmware is involved that could already handle these delays.
In this particular Intel Coffee Lake platform these delays are not
actually needed because there is an additional delay as part of the ACPI
power resource that is used to turn on power to the hierarchy but since
that additional delay is not required by any of standards (PCIe, ACPI)
it is not present in the Intel Ice Lake, for example where missing the
mandatory delays causes pciehp to start tearing down the stack too early
(links are not yet trained).
For this reason, change the PCIe portdrv PM resume hooks so that they
perform the mandatory delays before the downstream component gets
resumed. We perform the delays before port services are resumed because
otherwise pciehp might find that the link is not up (even if it is just
training) and tears-down the hierarchy.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Log messages with pci_dev, not pcie_device. Factor out common message
prefixes with dev_fmt().
Example output change:
- aer 0000:00:00.0:pci002: AER enabled with IRQ ...
+ pcieport 0000:00:00.0: AER: enabled with IRQ ...
Link: https://lore.kernel.org/lkml/20190509141456.223614-5-helgaas@kernel.org
Signed-off-by: Frederick Lawler <fred@fredlawl.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Replace dev_printk(KERN_DEBUG) with dev_info() or dev_err() to be more
consistent with other logging.
These could be converted to dev_dbg(), but that depends on
CONFIG_DYNAMIC_DEBUG and DEBUG, and we want most of these messages to
*always* be in the dmesg log.
Also, use dev_fmt() to add the service name. Example output change:
- pcieport 0000:80:10.0: Signaling PME with IRQ ...
+ pcieport 0000:80:10.0: PME: Signaling with IRQ ...
Link: https://lore.kernel.org/lkml/20190509141456.223614-3-helgaas@kernel.org
Signed-off-by: Frederick Lawler <fred@fredlawl.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Replace dev_printk(KERN_DEBUG) with dev_info() or dev_err() to be more
consistent with other logging.
These could be converted to dev_dbg(), but that depends on
CONFIG_DYNAMIC_DEBUG and DEBUG, and we want most of these messages to
*always* be in the dmesg log.
Also remove a redundant kzalloc() failure message.
Link: https://lore.kernel.org/lkml/20190509141456.223614-2-helgaas@kernel.org
Signed-off-by: Frederick Lawler <fred@fredlawl.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
e8303bb7a7 ("PCI/LINK: Report degraded links via link bandwidth
notification") added dmesg logging whenever a link changes speed or width
to a state that is considered degraded. Unfortunately, it cannot
differentiate signal integrity-related link changes from those
intentionally initiated by an endpoint driver, including drivers that may
live in userspace or VMs when making use of vfio-pci. Some GPU drivers
actively manage the link state to save power, which generates a stream of
messages like this:
vfio-pci 0000:07:00.0: 32.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x16 link at 0000:00:02.0 (capable of 64.000 Gb/s with 5 GT/s x16 link)
Since we can't distinguish the intentional changes from the signal
integrity issues, leave the reporting turned off by default. Add a Kconfig
option to turn it on if desired.
Fixes: e8303bb7a7 ("PCI/LINK: Report degraded links via link bandwidth notification")
Link: https://lore.kernel.org/linux-pci/20190501142942.26972-1-keith.busch@intel.com
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The Interrupt Message Number in the PCIe Capabilities register (PCIe r4.0,
sec 7.5.3.2) indicates which MSI/MSI-X vector is shared by interrupts
related to the PCIe Capability, including Link Bandwidth Management and
Link Autonomous Bandwidth Interrupts (Link Control, 7.5.3.7), Command
Completed and Hot-Plug Interrupts (Slot Control, 7.5.3.10), and the PME
Interrupt (Root Control, 7.5.3.12).
pcie_message_numbers() checked whether we want to enable PME or Hot-Plug
interrupts but neglected to check for Link Bandwidth Management, so if we
only wanted the Bandwidth Management interrupts, it decided we didn't need
any vectors at all. Then pcie_port_enable_irq_vec() tried to reallocate
zero vectors, which failed, resulting in fallback to INTx.
On some systems, e.g., an X79-based workstation, that INTx seems broken or
not handled correctly, so we got spurious IRQ16 interrupts for Bandwidth
Management events.
Change pcie_message_numbers() so that if we want Link Bandwidth Management
interrupts, we use the shared MSI/MSI-X vector from the PCIe Capabilities
register.
Fixes: e8303bb7a7 ("PCI/LINK: Report degraded links via link bandwidth notification")
Link: https://lore.kernel.org/lkml/155597243666.19387.1205950870601742062.stgit@gimli.home
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If the bandwidth notification interrupt is left unmasked when entering
suspend to idle, it triggers immediately bringing the system back to
working state.
To keep that from happening, disable the interrupt when entering system
sleep and enable it again during resume.
Reported-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Transform wait code to a "do {} while (time_before())" loop as recommended
by reviewer. No functional change intended.
Signed-off-by: Stefan Mätje <stefan.maetje@esd.eu>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Due to an erratum in some Pericom PCIe-to-PCI bridges in reverse mode
(conventional PCI on primary side, PCIe on downstream side), the Retrain
Link bit needs to be cleared manually to allow the link training to
complete successfully.
If it is not cleared manually, the link training is continuously restarted
and no devices below the PCI-to-PCIe bridge can be accessed. That means
drivers for devices below the bridge will be loaded but won't work and may
even crash because the driver is only reading 0xffff.
See the Pericom Errata Sheet PI7C9X111SLB_errata_rev1.2_102711.pdf for
details. Devices known as affected so far are: PI7C9X110, PI7C9X111SL,
PI7C9X130.
Add a new flag, clear_retrain_link, in struct pci_dev. Quirks for affected
devices set this bit.
Note that pcie_retrain_link() lives in aspm.c because that's currently the
only place we use it, but this erratum is not specific to ASPM, and we may
retrain links for other reasons in the future.
Signed-off-by: Stefan Mätje <stefan.maetje@esd.eu>
[bhelgaas: apply regardless of CONFIG_PCIEASPM]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
CC: stable@vger.kernel.org
Factor out pcie_retrain_link() to use for Pericom Retrain Link quirk. No
functional change intended.
Signed-off-by: Stefan Mätje <stefan.maetje@esd.eu>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
CC: stable@vger.kernel.org
If a multi-function device's bandwidth is already limited when it is
enumerated, a message is logged only for function 0. By contrast, when
downtraining occurs after enumeration, a message is logged for all
functions. That's because the former uses pcie_report_downtraining(),
whereas the latter uses __pcie_print_link_status() (which doesn't filter
functions != 0). I am seeing this happen on a MacBookPro9,1 with a GPU
(function 0) and an integrated HDA controller (function 1).
Avoid this incongruence by calling pcie_report_downtraining() in both
cases.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alexandru Gagniuc <alex.gagniuc@dellteam.com>
When booting a MacBookPro9,1, duplicate link downtraining messages are
logged for the devices directly attached to the two CPU-internal Root Ports
of the Core i7 3615QM: Once on device enumeration and once on enablement
of the bandwidth notification interrupt on the Root Ports.
Duplicate messages do not occur with Root Ports on the PCH and Downstream
Ports on the Thunderbolt controller: Only a single message is logged for
these, namely on device enumeration.
The reason for the duplicate messages is a stale interrupt in the Link
Status register of the 3615QM's internal Root Ports. Avoid by clearing the
interrupt before enabling it.
An alternative approach would be to clear the interrupt already on device
enumeration or to report link downtraining only if the speed has changed.
That way, link downtraining occurring between device enumeration and
enablement of the bandwidth notification interrupt could be caught.
However clearing stale interrupts before enabling them is a standard
operating procedure for any driver and keeping the two steps in one place
makes the code easier to follow.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alexandru Gagniuc <alex.gagniuc@dellteam.com>
A threaded IRQ with a NULL handler does not work with level-triggered
interrupts. request_threaded_irq() will return an error:
genirq: Threaded irq requested with handler=NULL and !ONESHOT for irq 16
pcie_bw_notification: probe of 0000:00:1b.0:pcie010 failed with error -22
For level interrupts we need to silence the interrupt before exiting the
IRQ handler, so just clear the PCI_EXP_LNKSTA_LBMS bit there.
Fixes: e8303bb7a7 ("PCI/LINK: Report degraded links via link bandwidth notification")
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
- Blacklist Gigabyte X299 Root Port power management to fix Thunderbolt
hotplug (Mika Westerberg)
- Revert runtime PM suspend/resume callbacks that broke PME on network
cable plug (Mika Westerberg)
- Disable Data Link State Changed interrupts to prevent wakeup
immediately after suspend (Mika Westerberg)
* pci/pm:
PCI/PME: Fix possible use-after-free on remove
PCI/PME: Fix hotplug/sysfs remove deadlock in pcie_pme_remove()
PCI: pciehp: Disable Data Link Layer State Changed event on suspend
Revert "PCI/PME: Implement runtime PM callbacks"
PCI: Blacklist power management of Gigabyte X299 DESIGNARE EX PCIe ports
- Allow portdrv to claim subtractive decode Ports so PCIe services will
work for them (Honghui Zhang)
- Report PCIe links that become degraded at run-time (Alexandru Gagniuc)
* pci/portdrv:
PCI/LINK: Report degraded links via link bandwidth notification
PCI/portdrv: Support PCIe services on subtractive decode bridges
PCI/portdrv: Use conventional Device ID table formatting
- Mark expected switch fall-through (Mathieu Malaterre)
- Use of_node_name_eq() for node name comparisons (Rob Herring)
- Add ACS and pciehp quirks for HXT SD4800 (Shunyong Yang)
- Consolidate Rohm Vendor ID definitions (Andy Shevchenko)
- Use u32 (not __u32) for things not exposed to userspace (Logan
Gunthorpe)
- Fix locking semantics of bus and slot reset interfaces (Alex
Williamson)
- Update PCIEPORTBUS Kconfig help text (Hou Zhiqiang)
* pci/misc:
PCI: Update PCIEPORTBUS Kconfig help text
PCI: Fix "try" semantics of bus and slot reset
PCI: Clean up usage of __u32 type
genirq/msi: Clean up usage of __u8/__u16 types
PCI: Move Rohm Vendor ID to generic list
PCI: pciehp: Add HXT quirk for Command Completed errata
PCI: Add ACS quirk for HXT SD4800
PCI: Add HXT vendor ID
PCI: Use of_node_name_eq() for node name comparisons
PCI: Mark expected switch fall-through
The Virtual Channel service has been removed and Downstream Port
Containment has been added, so update the symbol description to be
consistent with the current code.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
A warning is generated when a PCIe device is probed with a degraded link,
but there was no similar mechanism to warn when the link becomes degraded
after probing. The Link Bandwidth Notification provides this mechanism.
Use the Link Bandwidth Management Interrupt to detect bandwidth changes,
and rescan the bandwidth, looking for the weakest point. This is the same
logic used in probe().
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
In remove(), ensure that the PME work cannot run after kfree() is called.
Otherwise, this could result in a use-after-free.
This issue was detected with the help of Coccinelle.
Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Sinan Kaya <okaya@kernel.org>
Cc: Frederick Lawler <fred@fredlawl.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Dongdong reported a deadlock triggered by a hotplug event during a sysfs
"remove" operation:
pciehp 0000:00:0c.0:pcie004: Slot(0-1): Link Up
# echo 1 > 0000:00:0c.0/remove
PME and hotplug share an MSI/MSI-X vector. The sysfs "remove" side is:
remove_store
pci_stop_and_remove_bus_device_locked
pci_lock_rescan_remove
pci_stop_and_remove_bus_device
...
pcie_pme_remove
pcie_pme_suspend
synchronize_irq # wait for hotplug IRQ handler
pci_unlock_rescan_remove
The hotplug side is:
pciehp_ist
pciehp_handle_presence_or_link_change
pciehp_configure_device
pci_lock_rescan_remove # wait for pci_unlock_rescan_remove()
INFO: task bash:10913 blocked for more than 120 seconds.
# ps -ax |grep D
PID TTY STAT TIME COMMAND
10913 ttyAMA0 Ds+ 0:00 -bash
14022 ? D 0:00 [irq/745-pciehp]
# cat /proc/14022/stack
__switch_to+0x94/0xd8
pci_lock_rescan_remove+0x20/0x28
pciehp_configure_device+0x30/0x140
pciehp_handle_presence_or_link_change+0x324/0x458
pciehp_ist+0x1dc/0x1e0
# cat /proc/10913/stack
__switch_to+0x94/0xd8
synchronize_irq+0x8c/0xc0
pcie_pme_suspend+0xa4/0x118
pcie_pme_remove+0x20/0x40
pcie_port_remove_service+0x3c/0x58
...
pcie_port_device_remove+0x2c/0x48
pcie_portdrv_remove+0x68/0x78
pci_device_remove+0x48/0x120
...
pci_stop_bus_device+0x84/0xc0
pci_stop_and_remove_bus_device_locked+0x24/0x40
remove_store+0xa4/0xb8
dev_attr_store+0x44/0x60
sysfs_kf_write+0x58/0x80
It is incorrect to call pcie_pme_suspend() from pcie_pme_remove() for two
reasons.
First, pcie_pme_suspend() calls synchronize_irq(), which will wait for the
native hotplug interrupt handler as well as for the PME one, because they
share one IRQ (as per the spec). That may deadlock if hotplug is signaled
while pcie_pme_remove() is running and the latter calls
pci_lock_rescan_remove() before the former.
Second, if pcie_pme_suspend() figures out that wakeup needs to be enabled
for the port, it will return without disabling the interrupt as expected by
pcie_pme_remove() which was overlooked by commit c7b5a4e6e8 ("PCI / PM:
Fix native PME handling during system suspend/resume").
To fix that, rework pcie_pme_remove() to disable the PME interrupt, clear
its status and prevent the PME worker function from re-enabling it before
calling free_irq() on it, which should be sufficient.
Fixes: c7b5a4e6e8 ("PCI / PM: Fix native PME handling during system suspend/resume")
Link: https://lore.kernel.org/linux-pci/c7697e7c-e1af-13e4-8491-0a3996e6ab5d@huawei.com
Reported-by: Dongdong Liu <liudongdong3@huawei.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
[bhelgaas: add URL and deadlock details from Dongdong]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously dpc_handler() called aer_get_device_error_info() without
initializing info->severity, so aer_get_device_error_info() relied on
uninitialized data.
Add dpc_get_aer_uncorrect_severity() to read the port's AER status, mask,
and severity registers and set info->severity.
Also, clear the port's AER fatal error status bits.
Fixes: 8aefa9b0d9 ("PCI/DPC: Print AER status in DPC event handling")
Signed-off-by: Dongdong Liu <liudongdong3@huawei.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Cc: stable@vger.kernel.org # v4.19+
The Class Code for subtractive decode PCI-to-PCI bridge is 060401h; add an
entry to make portdrv support this type of bridge. This allows use of PCIe
services on subtractive decode ports.
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
[bhelgaas: add braces surrounding entry]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The pci_device_id table was technically correct, but unusually formatted,
which made adding entries error-prone. Change the format so it's obvious
how to add entries.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This reverts commit 0e157e5286.
Heiner reported that the commit in question prevents his network adapter
from triggering PME and waking up when network cable is plugged.
The commit tried to prevent root port waking up from D3cold immediately but
looks like disabing root port PME interrupt is not the right way to fix
that issue so revert it now. The patch following proposes an alternative
solution to that issue.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=202103
Fixes: 0e157e5286 ("PCI/PME: Implement runtime PM callbacks")
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
CC: stable@vger.kernel.org # v4.20+
match_string() returns the array index of a matching string. Use it
instead of the open-coded implementation.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
- Expand Kconfig "PF" acronyms (Randy Dunlap)
- Update MAINTAINERS for arch/x86/kernel/early-quirks.c (Bjorn Helgaas)
- Add missing include to drivers/pci.h (Alexandru Gagniuc)
- Override Synopsys USB 3.x HAPS device class so dwc3-haps can claim it
instead of xhci (Thinh Nguyen)
* pci/misc:
PCI: Override Synopsys USB 3.x HAPS device class
PCI: Move Synopsys HAPS platform device IDs
PCI: Add missing include to drivers/pci.h
PCI: Remove unnecessary space before function pointer arguments
MAINTAINERS: Add x86 early-quirks.c file pattern to PCI subsystem
PCI: Expand the "PF" acronym in Kconfig help text
ASPM does not make use of the children or link LIST_HEADs declared in
struct pcie_link_state and defined in alloc_pcie_link_state(). Therefore,
remove these lists.
No functional change intended.
Signed-off-by: Frederick Lawler <fred@fredlawl.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
ecae65e133 ("PCI/AER: Use kfifo_in_spinlocked() to insert locked
elements") replaced kfifo_put() with kfifo_in_spinlocked(), but passed the
*size* of the queue entry, where kfifo_in_spinlocked() expects the *number*
of entries to be copied.
We want to insert only one element into kfifo, not "sizeof(entry) = 16".
Without this patch, we would get 15 uninitialized elements.
Fixes: ecae65e133 ("PCI/AER: Use kfifo_in_spinlocked() to insert locked elements")
Signed-off-by: Yanjiang Jin <yanjiang.jin@hxt-semitech.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Make spacing more consistent in the code for function pointer declarations
based on checkpatch.pl.
Signed-off-by: Benjamin Young <youngcdev@gmail.com>
[bhelgaas: make similar changes in include/linux/pci.h]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This reverts commit 17c9148736.
Rafael found that this commit broke the SD card reader in his
Acer Aspire S5. Details of the problem are in the bugzilla below.
Fixes: 17c9148736 ("PCI/ASPM: Do not initialize link state when aspm_disabled is set")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=201801
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
- Differentiate between pciehp surprise and safe removal (Lukas Wunner)
- Remove unnecessary pciehp includes (Lukas Wunner)
- Drop pciehp hotplug_slot_ops wrappers (Lukas Wunner)
- Tolerate PCIe Slot Presence Detect being hardwired to zero to
workaround broken hardware, e.g., the Wilocity switch/wireless device
(Lukas Wunner)
- Unify pciehp controller & slot structs (Lukas Wunner)
- Constify hotplug_slot_ops (Lukas Wunner)
- Drop hotplug_slot_info (Lukas Wunner)
- Embed hotplug_slot struct into users instead of allocating it
separately (Lukas Wunner)
- Initialize PCIe port service drivers directly instead of relying on
initcall ordering (Keith Busch)
- Restore PCI config state after a slot reset (Keith Busch)
- Save/restore DPC config state along with other PCI config state (Keith
Busch)
- Reference count devices during AER handling to avoid race issue with
concurrent hot removal (Keith Busch)
- If an Upstream Port reports ERR_FATAL, don't try to read the Port's
config space because it is probably unreachable (Keith Busch)
- During error handling, use slot-specific reset instead of secondary
bus reset to avoid link up/down issues on hotplug ports (Keith Busch)
- Restore previous AER/DPC handling that does not remove and re-enumerate
devices on ERR_FATAL (Keith Busch)
- Notify all drivers that may be affected by error recovery resets (Keith
Busch)
- Always generate error recovery uevents, even if a driver doesn't have
error callbacks (Keith Busch)
- Make PCIe link active reporting detection generic (Keith Busch)
- Support D3cold in PCIe hierarchies during system sleep and runtime,
including hotplug and Thunderbolt ports (Mika Westerberg)
- Handle hpmemsize/hpiosize kernel parameters uniformly, whether slots
are empty or occupied (Jon Derrick)
- Remove duplicated include from pci/pcie/err.c and unused variable from
cpqphp (YueHaibing)
- Remove driver pci_cleanup_aer_uncorrect_error_status() calls (Oza
Pawandeep)
- Uninline PCI bus accessors for better ftracing (Keith Busch)
- Remove unused AER Root Port .error_resume method (Keith Busch)
- Use kfifo in AER instead of a local version (Keith Busch)
- Use threaded IRQ in AER bottom half (Keith Busch)
- Use managed resources in AER core (Keith Busch)
- Reuse pcie_port_find_device() for AER injection (Keith Busch)
- Abstract AER interrupt handling to disconnect error injection (Keith
Busch)
- Refactor AER injection callbacks to simplify future improvments (Keith
Busch)
* pci/hotplug:
PCI/AER: Refactor error injection fallbacks
PCI/AER: Abstract AER interrupt handling
PCI/AER: Reuse existing pcie_port_find_device() interface
PCI/AER: Use managed resource allocations
PCI/AER: Use threaded IRQ for bottom half
PCI/AER: Use kfifo_in_spinlocked() to insert locked elements
PCI/AER: Use kfifo for tracking events instead of reimplementing it
PCI/AER: Remove error source from AER struct aer_rpc
PCI/AER: Remove unused aer_error_resume()
PCI: Uninline PCI bus accessors for better ftracing
PCI/AER: Remove pci_cleanup_aer_uncorrect_error_status() calls
PCI: pnv_php: Use kmemdup()
PCI: cpqphp: Remove set but not used variable 'physical_slot'
PCI/ERR: Remove duplicated include from err.c
PCI: Equalize hotplug memory and io for occupied and empty slots
PCI / ACPI: Whitelist D3 for more PCIe hotplug ports
ACPI / property: Allow multiple property compatible _DSD entries
PCI/PME: Implement runtime PM callbacks
PCI: pciehp: Implement runtime PM callbacks
PCI/portdrv: Add runtime PM hooks for port service drivers
PCI/portdrv: Resume upon exit from system suspend if left runtime suspended
PCI: pciehp: Do not handle events if interrupts are masked
PCI: pciehp: Disable hotplug interrupt during suspend
PCI / ACPI: Enable wake automatically for power managed bridges
PCI: Do not skip power-managed bridges in pci_enable_wake()
PCI: Make link active reporting detection generic
PCI: Unify device inaccessible
PCI/ERR: Always report current recovery status for udev
PCI/ERR: Simplify broadcast callouts
PCI/ERR: Run error recovery callbacks for all affected devices
PCI/ERR: Handle fatal error recovery
PCI/ERR: Use slot reset if available
PCI/AER: Don't read upstream ports below fatal errors
PCI/AER: Take reference on error devices
PCI/DPC: Save and restore config state
PCI: portdrv: Restore PCI config state on slot reset
PCI: portdrv: Initialize service drivers directly
PCI: hotplug: Document TODOs
PCI: hotplug: Embed hotplug_slot
PCI: hotplug: Drop hotplug_slot_info
PCI: hotplug: Constify hotplug_slot_ops
PCI: pciehp: Reshuffle controller struct for clarity
PCI: pciehp: Rename controller struct members for clarity
PCI: pciehp: Unify controller and slot structs
PCI: pciehp: Tolerate Presence Detect hardwired to zero
PCI: pciehp: Drop hotplug_slot_ops wrappers
PCI: pciehp: Drop unnecessary includes
PCI: pciehp: Differentiate between surprise and safe removal
PCI: Simplify disconnected marking
Move the bus ops fallback into separate functions. No functional change
here.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The aer_inject module was directly calling aer_irq(). This required the
AER driver export its private IRQ handler for no other reason than to
support error injection. A driver should not have to expose its private
interfaces, so use the IRQ subsystem to route injection to the AER driver,
and make aer_irq() a private interface.
This provides additional benefits:
First, directly calling the IRQ handler bypassed the IRQ subsytem so the
injection wasn't really synthesizing what happens if a shared AER interrupt
occurs.
The error injection had to provide the callback data directly, which may be
racing with a removal that is freeing that structure. The IRQ subsystem
can handle that race.
Finally, using the IRQ subsystem automatically reacts to threaded IRQs,
keeping the error injection abstracted from that implementation detail.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The port services driver already provides a method to find the pcie_device
for a service. Export that function, use it from the aer_inject module,
and remove the duplicate functionality.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use the managed device resource allocations for the service data so the AER
driver doesn't need to manage it, further simplifying this driver.
Link: https://lore.kernel.org/linux-pci/20180918235848.26694-12-keith.busch@intel.com
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
'default n' is the default value for any bool or tristate Kconfig setting
so there is no need to write it explicitly.
Also since commit f467c5640c ("kconfig: only write '# CONFIG_FOO is not
set' for visible symbols") the Kconfig behavior is the same regardless of
'default n' being present or not:
...
One side effect of (and the main motivation for) this change is making
the following two definitions behave exactly the same:
config FOO
bool
config FOO
bool
default n
With this change, neither of these will generate a
'# CONFIG_FOO is not set' line (assuming FOO isn't selected/implied).
That might make it clearer to people that a bare 'default n' is
redundant.
...
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The threaded IRQ is naturally single threaded as desired, so use that to
simplify the AER bottom half handler. Since the root port structure has
much less to do now, remove the rpc construction helper routine.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use the recommended kernel API for writing to a concurrently-accessed
kfifo. No functional change here.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The kernel provides a generic FIFO implementation, so no need to reinvent
that capability in a driver. Replace the AER-specific implementation with
the kernel-provided kfifo. Since the interrupt handler producer and work
queue consumer run single threaded, there is no need for additional
locking, so remove that lock, too.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The AER struct aer_rpc was carrying a copy of the error source simply as a
temperary variable. Remove that from the structure and use a stack
variable for the purpose.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The error recovery callbacks are only run on child devices. A Root Port is
never a child device, so this error resume callback was never invoked.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Basically we need to do the same steps than what we do when system sleep is
entered and disable PME interrupt when the root port is runtime suspended.
This prevents spurious wakeups immediately when the port is transitioned
into D3cold.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When PCIe port is runtime suspended/resumed some extra steps might be
needed to be executed from the port service driver side. For instance we
may need to disable PCIe hotplug interrupt to prevent it from triggering
immediately when PCIe link to the downstream component goes down.
To make the above possible add optional ->runtime_suspend() and
->runtime_resume() callbacks to struct pcie_port_service_driver and call
them for each port service in runtime suspend/resume callbacks of portdrv.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[bhelgaas: adjust "slot->state" for 5790a9c78e ("PCI: pciehp: Unify
controller and slot structs")]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently we try to keep PCIe ports runtime suspended over system suspend
if possible. This mostly happens when entering suspend-to-idle because
there is no need to re-configure wake settings.
This causes problems if the parent port goes into D3cold and it gets
resumed upon exit from system suspend. This may happen for example if the
port is part of PCIe switch and the same switch is connected to a PCIe
endpoint that needs to be resumed. The way exit from D3cold works according
PCIe 4.0 spec 5.3.1.4.2 is that power is restored and cold reset is
signaled. After this the device is in D0unitialized state keeping PME
context if it supports wake from D3cold.
The problem occurs when a PCIe hotplug port is left suspended and the
parent port goes into D3cold and back to D0: the port keeps its PME context
but since everything else is reset back to defaults (D0unitialized) it is
not set to detect hotplug events anymore.
For this reason change the PCIe portdrv power management logic so that it
is fine to keep the port runtime suspended over system suspend but it needs
to be resumed upon exit to make sure it gets properly re-initialized.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The spec has timing requirements when waiting for a link to become active
after a conventional reset. Implement those hard delays when waiting for
an active link so pciehp and dpc drivers don't need to duplicate this.
For devices that don't support data link layer active reporting, wait the
fixed time recommended by the PCIe spec.
Signed-off-by: Keith Busch <keith.busch@intel.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Bring surprise removals and permanent failures together so we no longer
need separate flags. The implementation enforces that error handling will
not be able to override a surprise removal's permanent channel failure.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
A device still participates in error recovery even if it doesn't have
the error callbacks.
Always provide the status for user event watchers.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
There is no point in having a generic broadcast function if it needs to
have special cases for each callback it broadcasts.
Abstract the error broadcast to only the necessary information and removes
the now unnecessary helper to walk the bus.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
If an Endpoint reported an error with ERR_FATAL, we previously ran driver
error recovery callbacks only for the Endpoint's driver. But if we reset a
Link to recover from the error, all downstream components are affected,
including the Endpoint, any multi-function peers, and children of those
peers.
Initiate the Link reset from the deepest Downstream Port that is
reliable, and call the error recovery callbacks for all its children.
If a Downstream Port (including a Root Port) reports an error, we assume
the Port itself is reliable and we need to reset its downstream Link. In
all other cases (Switch Upstream Ports, Endpoints, Bridges, etc), we assume
the Link leading to the component needs to be reset, so we initiate the
reset at the parent Downstream Port.
This allows two other clean-ups. First, we currently only use a Link
reset, which can only be initiated using a Downstream Port, so we can
remove checks for Endpoints. Second, the Downstream Port where we initiate
the Link reset is reliable (unlike components downstream from it), so the
special cases for error detect and resume are no longer necessary.
Signed-off-by: Keith Busch <keith.busch@intel.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
We don't need to be paranoid about the topology changing while handling an
error. If the device has changed in a hotplug capable slot, we can rely on
the presence detection handling to react to a changing topology.
Restore the fatal error handling behavior that existed before merging DPC
with AER with 7e9084b367 ("PCI/AER: Handle ERR_FATAL with removal and
re-enumeration of devices").
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
The secondary bus reset may have link side effects that a hotplug capable
port may incorrectly react to. Use the slot specific reset for hotplug
ports, fixing the undesirable link down-up handling during error
recovering.
Signed-off-by: Keith Busch <keith.busch@intel.com>
[bhelgaas: fold in
https://lore.kernel.org/linux-pci/20180926152326.14821-1-keith.busch@intel.com
for issue reported by Stephen Rothwell <sfr@canb.auug.org.au>]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
The AER driver has never read the config space of an endpoint that reported
a fatal error because the link to that device is considered unreliable.
An ERR_FATAL from an upstream port almost certainly indicates an error on
its upstream link, so we can't expect to reliably read its config space for
the same reason.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Error handling may be running in parallel with a hot removal. Reference
count the device during AER handling so the device can not be freed while
AER wants to reference it.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
This patch provides DPC save and restore capabilities. This is necessary
for the driver to observe DPC events in the event the configuration space
needs to be restored after a reset.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
The port's config space may be cleared after a link reset, which wipes out
the bridge's bus and memory windows. Restore the config space that was
saved during probe so we can access downstream devices.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
The PCI port driver saves the PCI state after initializing the device with
the applicable service devices. This was, however, before the service
drivers were even registered because PCI probe happens before the
device_initcall initialized those service drivers. The config space state
that the services set up were not being saved. The end result would cause
PCI devices to not react to events that the drivers think they did if the
PCI state ever needed to be restored.
Fix this by changing the service drivers from using the init calls to
having the portdrv driver calling the services directly. This will get the
state saved as desired, while making the relationship between the port
driver and the services under it more explicit in the code.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Now that ASPM is configured for *all* PCIe devices at boot, a problem is
seen with systems that set the FADT NO_ASPM bit. This bit indicates that
the OS should not alter the ASPM state, but when
pcie_aspm_init_link_state() runs it only checks for !aspm_support_enabled.
This misses the ACPI_FADT_NO_ASPM case because that is setting
aspm_disabled.
The result is systems may hang at boot after 1302fcf; avoidable if they
boot with pcie_aspm=off (sets !aspm_support_enabled).
Fix this by having aspm_init_link_state() check for either
!aspm_support_enabled or acpm_disabled.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=201001
Fixes: 1302fcf0d0 ("PCI: Configure *all* devices, not just hot-added ones")
Signed-off-by: Patrick Talbert <ptalbert@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Commit 89ee9f7680 ("PCI: Add device disconnected state") iterates over
the devices on a parent bus, marks each as disconnected, then marks
each device's children as disconnected using pci_walk_bus().
The same can be achieved more succinctly by calling pci_walk_bus() on
the parent bus. Moreover, this does not need to wait until acquiring
pci_lock_rescan_remove(), so move it out of that critical section.
The critical section in err.c contains a pci_dev_get() / pci_dev_put()
pair which was apparently copy-pasted from pciehp_pci.c. In the latter
it serves the purpose of holding the struct pci_dev in place until the
Command register is updated. err.c doesn't do anything like that, hence
the pair is unnecessary. Remove it.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Oza Pawandeep <poza@codeaurora.org>
Cc: Sinan Kaya <okaya@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Upon removal of the last device on a bus, the link_state of the bridge
leading to that bus is sought to be torn down by having pci_stop_dev()
call pcie_aspm_exit_link_state().
When ASPM was originally introduced by commit 7d715a6c1a ("PCI: add
PCI Express ASPM support"), it determined whether the device being
removed is the last one by calling list_empty() on the bridge's
subordinate devices list. That didn't work because the device is only
removed from the list slightly later in pci_destroy_dev().
Commit 3419c75e15 ("PCI: properly clean up ASPM link state on device
remove") attempted to fix it by calling list_is_last(), but that's not
correct either because it checks whether the device is at the *end* of
the list, not whether it's the last one *left* in the list. If the user
removes the device which happens to be at the end of the list via sysfs
but other devices are preceding the device in the list, the link_state
is torn down prematurely.
The real fix is to move the invocation of pcie_aspm_exit_link_state() to
pci_destroy_dev() and reinstate the call to list_empty(). Remove a
duplicate check for dev->bus->self because pcie_aspm_exit_link_state()
already contains an identical check.
Fixes: 7d715a6c1a ("PCI: add PCI Express ASPM support")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Shaohua Li <shaohua.li@intel.com>
Cc: stable@vger.kernel.org # v2.6.26
- To avoid bus errors, enable PASID only if entire path supports End-End
TLP prefixes (Sinan Kaya)
- Unify slot and bus reset functions and remove hotplug knowledge from
callers (Sinan Kaya)
- Add Function-Level Reset quirks for Intel and Samsung NVMe devices to
fix guest reboot issues (Alex Williamson)
- Add function 1 DMA alias quirk for Marvell 88SS9183 PCIe SSD Controller
(Bjorn Helgaas)
* pci/virtualization:
PCI: Add function 1 DMA alias quirk for Marvell 88SS9183
PCI: Delay after FLR of Intel DC P3700 NVMe
PCI: Disable Samsung SM961/PM961 NVMe before FLR
PCI: Export pcie_has_flr()
PCI: Rename pci_try_reset_bus() to pci_reset_bus()
PCI: Deprecate pci_reset_bus() and pci_reset_slot() functions
PCI: Unify try slot and bus reset API
PCI: Hide pci_reset_bridge_secondary_bus() from drivers
IB/hfi1: Use pci_try_reset_bus() for initiating PCI Secondary Bus Reset
PCI: Handle error return from pci_reset_bridge_secondary_bus()
PCI/IOV: Tidy pci_sriov_set_totalvfs()
PCI: Enable PASID only if entire path supports End-End TLP prefixes
# Conflicts:
# drivers/pci/hotplug/pciehp_hpc.c
- Defer DPC event handling to work queue (Keith Busch)
- Use threaded IRQ for DPC bottom half (Keith Busch)
- Print AER status while handling DPC events (Keith Busch)
* pci/dpc:
PCI/DPC: Remove indirection waiting for inactive link
PCI/DPC: Use threaded IRQ for bottom half handling
PCI/DPC: Print AER status in DPC event handling
PCI/DPC: Remove rp_pio_status from dpc struct
PCI/DPC: Defer event handling to work queue
PCI/DPC: Leave interrupts enabled while handling event
- Use sysfs_match_string() to simplify ASPM sysfs parsing (Andy
Shevchenko)
- Remove unnecessary includes of <linux/pci-aspm.h> (Bjorn Helgaas)
* pci/aspm:
PCI: Remove unnecessary include of <linux/pci-aspm.h>
iwlwifi: Remove unnecessary include of <linux/pci-aspm.h>
ath9k: Remove unnecessary include of <linux/pci-aspm.h>
igb: Remove unnecessary include of <linux/pci-aspm.h>
PCI/ASPM: Convert to use sysfs_match_string() helper
- Decode AER errors with names similar to "lspci" (Tyler Baicar)
- Expose AER statistics in sysfs (Rajat Jain)
- Clear AER status bits selectively based on the type of recovery (Oza
Pawandeep)
- Honor "pcie_ports=native" even if HEST sets FIRMWARE_FIRST (Alexandru
Gagniuc)
- Don't clear AER status bits if we're using the "Firmware-First"
strategy where firmware owns the registers (Alexandru Gagniuc)
* pci/aer:
PCI/AER: Don't clear AER bits if error handling is Firmware-First
PCI/AER: Remove duplicate PCI_EXP_AER_FLAGS definition
PCI/portdrv: Remove pcie_portdrv_err_handler.slot_reset
PCI/AER: Clear device status bits during ERR_COR handling
PCI/AER: Clear device status bits during ERR_FATAL and ERR_NONFATAL
PCI/AER: Remove ERR_FATAL code from ERR_NONFATAL path
PCI/AER: Factor out ERR_NONFATAL status bit clearing
PCI/AER: Clear only ERR_NONFATAL bits during non-fatal recovery
PCI/AER: Clear only ERR_FATAL status bits during fatal recovery
PCI/AER: Honor "pcie_ports=native" even if HEST sets FIRMWARE_FIRST
PCI/AER: Add sysfs attributes for rootport cumulative stats
PCI/AER: Add sysfs attributes to provide AER stats and breakdown
PCI/AER: Define aer_stats structure for AER capable devices
PCI/AER: Move internal declarations to drivers/pci/pci.h
PCI/AER: Adopt lspci names for AER error decoding
PCI/AER: Expose internal API for obtaining AER information
# Conflicts:
# drivers/pci/pci.h
If the platform requests Firmware-First error handling, firmware is
responsible for reading and clearing AER status bits. If OSPM also clears
them, we may miss errors. See ACPI v6.2, sec 18.3.2.5 and 18.4.
This race is mostly of theoretical significance, as it is not easy to
reasonably demonstrate it in testing.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
[bhelgaas: add similar guards to pci_cleanup_aer_uncorrect_error_status()
and pci_aer_clear_fatal_status()]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The sysfs_match_string() helper returns index of the matching string in an
array. Use it in pcie_aspm_set_policy() to simplify the code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[bhelgaas: squash sysfs_match_string() fix into original patch for issue
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
PCI_EXP_AER_FLAGS was defined twice (with identical definitions), once
under #ifdef CONFIG_ACPI_APEI, and again at the top level. This looks like
my merge error from these commits:
fd3362cb73 ("PCI/AER: Squash aerdrv_core.c into aerdrv.c")
41cbc9eb1a ("PCI/AER: Squash ecrc.c into aerdrv.c")
Remove the duplicate PCI_EXP_AER_FLAGS definition.
Fixes: 41cbc9eb1a ("PCI/AER: Squash ecrc.c into aerdrv.c")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Oza Pawandeep <poza@codeaurora.org>
Thunderbolt hotplug ports that were occupied before system sleep resume
with their downstream link in "off" state. Only after the Thunderbolt
controller has reestablished the PCIe tunnels does the link go up.
As a result, a spurious Presence Detect Changed and/or Data Link Layer
State Changed event occurs.
The events are not immediately acted upon because tunnel reestablishment
happens in the ->resume_noirq phase, when interrupts are still disabled.
Also, notification of events may initially be disabled in the Slot
Control register when coming out of system sleep and is reenabled in the
->resume_noirq phase through:
pci_pm_resume_noirq()
pci_pm_default_resume_early()
pci_restore_state()
pci_restore_pcie_state()
It is not guaranteed that the events are acted upon at all: PCIe r4.0,
sec 6.7.3.4 says that "a port may optionally send an MSI when there are
hot-plug events that occur while interrupt generation is disabled, and
interrupt generation is subsequently enabled." Note the "optionally".
If an MSI is sent, pciehp will gratuitously turn the slot off and back
on once the ->resume_early phase has commenced.
If an MSI is not sent, the extant, unacknowledged events in the Slot
Status register will prevent future notification of presence or link
changes.
Commit 13c65840fe ("PCI: pciehp: Clear Presence Detect and Data Link
Layer Status Changed on resume") fixed the latter by clearing the events
in the ->resume phase. Move this to the ->resume_noirq phase to also
fix the gratuitous disable/enablement of the slot.
The commit further restored the Slot Control register in the ->resume
phase, but that's dispensable because as shown above it's already been
done in the ->resume_noirq phase.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Replace suspend_iter() and resume_iter() with a single function pm_iter()
to allow addition of port service callbacks for further power management
phases without having to add another iterator each time.
No functional change intended.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When an fatal error is received by a non-bridge device, the device is
removed, and pci_stop_and_remove_bus_device() deallocates the device
structure. The freed device structure is used by subsequent code to send
uevents and print messages.
Hold a reference on the device until we're finished using it. This is not
an ideal fix because pcie_do_fatal_recovery() should not use the device at
all after removing it, but that's too big a project for right now.
Fixes: 7e9084b367 ("PCI/AER: Handle ERR_FATAL with removal and re-enumeration of devices")
Signed-off-by: Thomas Tai <thomas.tai@oracle.com>
[bhelgaas: changelog, reduce get/put coverage]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The pci_error_handlers.slot_reset() callback is only used for non-bridge
devices (see broadcast_error_message()). Since portdrv only binds to
bridges, we don't need pcie_portdrv_slot_reset(), so remove it.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
[bhelgaas: changelog, remove pcie_portdrv_slot_reset() completely]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
In case of correctable error, the Correctable Error Detected bit in the
Device Status register is set. Clear it after handling the error.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Clear the device status bits while handling both ERR_FATAL and ERR_NONFATAL
cases.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
[bhelgaas: rename to pci_aer_clear_device_status(), declare internal to PCI
core instead of exposing it everywhere]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
broadcast_error_message() is only used for ERR_NONFATAL events, when the
state is always pci_channel_io_normal, so remove the unused alternate path.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
aer_error_resume() clears all ERR_NONFATAL error status bits. This is
exactly what pci_cleanup_aer_uncorrect_error_status(), so use that instead
of duplicating the code.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
[bhelgaas: split to separate patch]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pci_cleanup_aer_uncorrect_error_status() is called by driver .slot_reset()
methods when handling ERR_NONFATAL errors. Previously this cleared *all*
the bits, including ERR_FATAL bits.
Since we're only handling ERR_NONFATAL errors, clear only the ERR_NONFATAL
error status bits.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
[bhelgaas: split to separate patch]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
During recovery from fatal errors, we previously called
pci_cleanup_aer_uncorrect_error_status(), which cleared *all* uncorrectable
error status bits (both ERR_FATAL and ERR_NONFATAL).
Instead, call a new pci_aer_clear_fatal_status() that clears only the
ERR_FATAL bits (as indicated by the PCI_ERR_UNCOR_SEVER register).
Based-on-patch-by: Oza Pawandeep <poza@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Rename pci_reset_bridge_secondary_bus() to pci_bridge_secondary_bus_reset()
and move the declaration from linux/pci.h to drivers/pci.h to be used
internally in PCI directory only.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Commit 01fd61c0b9 ("PCI: Add a return type for
pci_reset_bridge_secondary_bus()") added a return value to the function to
return if a device is accessible following a reset. Callers are not
checking the value.
Pass error code up high in the stack if device is not accessible.
Fixes: 01fd61c0b9 ("PCI: Add a return type for pci_reset_bridge_secondary_bus()")
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Simplify waiting for the contained link to become inactive, removing the
indirection to a unnecessary DPC-specific handler.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Reviewed-by: Oza Pawandeep <poza@codeaurora.org>
Remove the work struct that was being used to handle a DPC event and use a
threaded IRQ instead.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Reviewed-by: Oza Pawandeep <poza@codeaurora.org>
A DPC enabled device suppresses ERR_(NON)FATAL messages, preventing the AER
handler from reporting error details. If the DPC trigger reason says the
downstream port detected the error, collect the AER uncorrectable status
for logging, then clear the status.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Reviewed-by: Oza Pawandeep <poza@codeaurora.org>
We don't need to save the rp pio status across multiple contexts as all
DPC event handling occurs in a single work queue context.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Reviewed-by: Oza Pawandeep <poza@codeaurora.org>
Move all event handling to the existing work queue, which will
make it simpler to pass event information to the handler.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Reviewed-by: Oza Pawandeep <poza@codeaurora.org>
Now that the DPC driver clears the interrupt status before exiting the
IRQ handler, we don't need to abuse the DPC control register to know if
a shared interrupt is for a new DPC event: a DPC port can not trigger
a second interrupt until the host clears the trigger status later in the
work queue handler.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Reviewed-by: Oza Pawandeep <poza@codeaurora.org>
According to the documentation, "pcie_ports=native", linux should use
native AER and DPC services. While that is true for the _OSC method
parsing, this is not the only place that is checked. Should the HEST
list PCIe ports as firmware-first, linux will not use native services.
This happens because aer_acpi_firmware_first() doesn't take 'pcie_ports'
into account. This is wrong. DPC uses the same logic when it decides
whether to load or not, so fixing this also fixes DPC not loading.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
[bhelgaas: return "false" from bool function (from kbuild robot)]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add sysfs attributes for rootport statistics (that are cumulative of all
the ERR_* messages seen on this PCI hierarchy).
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add sysfs attributes to provide total and breakdown of the AERs seen,
into different type of correctable, fatal and nonfatal errors:
/sys/bus/pci/devices/<dev>/aer_dev_correctable
/sys/bus/pci/devices/<dev>/aer_dev_fatal
/sys/bus/pci/devices/<dev>/aer_dev_nonfatal
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Define a structure to hold the AER statistics. There are 2 groups of
statistics: dev_* counters that are to be collected for all AER capable
devices and rootport_* counters that are collected for all (AER capable)
rootports only. Allocate and free this structure when device is added or
released (thus counters survive the lifetime of the device).
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Since pci_aer_init() and pci_no_aer() are used only internally, move their
declarations to the PCI internal header file. Also, no one cares about
return value of pci_aer_init(), so make it void.
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
lspci uses abbreviated naming for AER error strings. Adopt the same naming
convention for the AER printing so they match.
Signed-off-by: Tyler Baicar <tbaicar@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Oza Pawandeep <poza@codeaurora.org>
Export some common AER functions and structures for other PCI core drivers
to use. Since this is making the function externally visible inside the
PCI core, prepend "aer_" to the function name.
Signed-off-by: Keith Busch <keith.busch@intel.com>
[bhelgaas: move AER declarations from linux/aer.h to drivers/pci/pci.h]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Reviewed-by: Oza Pawandeep <poza@codeaurora.org>
Use "PCI Express" consistently in Kconfig text. No functional change
intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Hoist aerdrv.c, aer_inject.c up to drivers/pci/pcie/ so they're next to
other PCIe service drivers. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Most of the things in aerdrv.h are only used in aerdrv.c, so move them
there. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
The aer_irq() declaration is the only thing needed by aer_inject.c. Move
it to portdrv.h so we eventually get rid of aerdrv.h completely. No
functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Move pcie_aer_get_firmware_first() to portdrv.h, where it can be more
easily shared between AER and DPC. Then DPC no longer needs to include
aer/aerdrv.h. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
pcie_port_bus_type is already declared in portdrv.h, so remove the
unnecessary duplicate declaration in aerdrv.h. No functional change
intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reorder code to group probe/remove stuff together. No functional change
intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
- fix use-before-set error in ibmphp (Dan Carpenter)
- fix pciehp timeouts caused by Command Completed errata (Bjorn Helgaas)
- fix refcounting in pnv_php hotplug (Julia Lawall)
- clear pciehp Presence Detect and Data Link Layer Status Changed on
resume so we don't miss hotplug events (Mika Westerberg)
- only request pciehp control if we support it, so platform can use ACPI
hotplug otherwise (Mika Westerberg)
- convert SHPC to be builtin only (Mika Westerberg)
- request SHPC control via _OSC if we support it (Mika Westerberg)
- simplify SHPC handoff from firmware (Mika Westerberg)
* pci/hotplug:
PCI: Improve "partially hidden behind bridge" log message
PCI: Improve pci_scan_bridge() and pci_scan_bridge_extend() doc
PCI: Move resource distribution for single bridge outside loop
PCI: Account for all bridges on bus when distributing bus numbers
ACPI / hotplug / PCI: Drop unnecessary parentheses
ACPI / hotplug / PCI: Mark stale PCI devices disconnected
ACPI / hotplug / PCI: Don't scan bridges managed by native hotplug
PCI: hotplug: Add hotplug_is_native()
PCI: shpchp: Add shpchp_is_native()
PCI: shpchp: Fix AMD POGO identification
PCI: shpchp: Use dev_printk() for OSHP-related messages
PCI: shpchp: Remove get_hp_hw_control_from_firmware() wrapper
PCI: shpchp: Remove acpi_get_hp_hw_control_from_firmware() flags
PCI: shpchp: Rely on previous _OSC results
PCI: shpchp: Request SHPC control via _OSC when adding host bridge
PCI: shpchp: Convert SHPC to be builtin only
PCI: pciehp: Make pciehp_is_native() stricter
PCI: pciehp: Rename host->native_hotplug to host->native_pcie_hotplug
PCI: pciehp: Request control of native hotplug only if supported
PCI: pciehp: Clear Presence Detect and Data Link Layer Status Changed on resume
PCI: pnv_php: Add missing of_node_put()
PCI: pciehp: Add quirk for Command Completed errata
PCI: Add Qualcomm vendor ID
PCI: ibmphp: Fix use-before-set in get_max_bus_speed()
# Conflicts:
# drivers/acpi/pci_root.c
- disable ASPM L1.2 substate if we don't have LTR (Bjorn Helgaas)
- respect platform ownership of LTR (Bjorn Helgaas)
* pci/aspm:
PCI/ACPI: Request LTR control from platform before using it
PCI/ASPM: Disable ASPM L1.2 Substate if we don't have LTR
The AER driver only needed the pcie_device to get to the port pci_dev.
Save the pci_dev pointer directly in struct aer_rpc and remove the
unnecessary indirection.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Decode the Requester ID from the AER Error Source Register into domain/
bus/device/function format to match other logging. In cases where the ID
matches the device used for pci_err(), drop the extra ID completely so we
don't print it twice.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Just move the actual function up so that it is visible to its user
aer_recover_queue().
No functional changes.
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Our goal is to handle ERR_FATAL errors similarly, whether they are reported
via AER or via DPC. A previous commit changed AER so it handles ERR_FATAL
by calling driver .remove() methods and resetting the Link. DPC already
does that (although the Link reset is done automatically by hardware and
happens before we call the driver .remove() methods).
Restructure the DPC code so it calls the same pcie_do_fatal_recovery()
interface used by AER. This makes it clearer that we want to use the same
path.
Implement the .reset_link() method used by pcie_do_fatal_recovery(). For
DPC, the actual reset is done automatically by hardware, so we really only
have to wait for the Link to be inactive, then release the Port from DPC.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
[bhelgaas: changelog, DPC_FATAL is not a bitfield, can be sequential]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Pass the service type to pcie_do_fatal_recovery() instead of assuming AER.
We will make DPC also use pcie_do_fatal_recovery(), and it needs to do
things a little differently for AER and DPC.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
[bhelgaas: split to separate patch]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
PCIe ERR_NONFATAL errors mean a particular transaction is unreliable but
the Link is otherwise fully functional (PCIe r4.0, sec 6.2.2).
The AER driver handles these by logging the error details and calling
driver-supplied pci_error_handlers callbacks. It does not reset downstream
devices, does not remove them from the PCI subsystem, does not re-enumerate
them, and does not call their driver .remove() or .probe() methods.
But DPC driver previously enabled DPC on ERR_NONFATAL, so if the hardware
supports DPC, these errors caused a Link reset (performed automatically by
the hardware), followed by the DPC driver removing affected devices (which
calls their .remove() methods), bringing the Link back up, and
re-enumerating (which calls driver .probe() methods).
Disable ERR_NONFATAL DPC triggering so these errors will only be handled by
AER. This means drivers won't have to deal with different usage of their
pci_error_handlers callbacks and .probe() and .remove() methods based on
whether the platform has DPC support.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously pciehp_is_native() returned true for any PCI device in a
hierarchy where _OSC says we can use pciehp. This is incorrect because
bridges without PCI_EXP_SLTCAP_HPC capability should be managed by acpiphp
instead.
Improve pciehp_is_native() to return true only when PCI_EXP_SLTCAP_HPC is
set and the pciehp driver is present. In any other case return false
to let acpiphp handle those.
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[bhelgaas: remove NULL pointer check]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Rename host->native_hotplug to host->native_pcie_hotplug to make room for a
similar flag for SHPC hotplug.
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[bhelgaas: split to separate patch]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Move the error reporting callbacks from aerdrv_core.c to err.c, where they
can be used by DPC in addition to AER.
As part of aerdrv_core.c, these callbacks were built under CONFIG_PCIEAER.
Moving them to the new err.c means they will now be built under
CONFIG_PCIEPORTBUS, so adjust the definition of pci_uevent_ers() to match.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
[bhelgaas: in reset_link(), initialize "driver" even if CONFIG_PCIEAER is
unset, update pci_uevent_ers() #ifdef wrapper]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Rename error recovery interfaces with "pcie_" prefix so they can be made
non-static.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
[bhelgaas: move declaration to later patch, leave functions static]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
PCIe ERR_FATAL errors mean the Link is unreliable. Components on the Link
may need to be reset to return to reliable operation (PCIe r4.0, sec
6.2.2). We previously handled these errors much differently depending on
whether the platform supports Downstream Port Containment (DPC) (PCIe r4.0,
sec 6.2.10) or not.
The AER driver has historically logged the error details, called
driver-supplied pci_error_handlers callbacks, and reset the Link. This
reset downstream devices, but did not remove them from the PCI subsystem,
re-enumerate them, or call their driver .remove() or .probe() methods.
DPC is different because the hardware automatically disables the Link when
it detects ERR_FATAL, which resets downstream devices. There's no
opportunity for pci_error_handlers callbacks before resetting the Link.
The DPC driver removes affected devices (which calls their driver .remove()
methods), brings the Link back up, and re-enumerates (which calls driver
.probe() methods).
Align AER ERR_FATAL handling with DPC by resetting the Link in software,
skipping the driver pci_error_handlers callbacks, removing the devices from
the PCI subsystem, and re-enumerating. The idea is that drivers and
devices should see the same behavior for ERR_FATAL events, regardless of
whether they're handled by AER or DPC.
Here are the basic ERR_FATAL recovery steps, showing the previous AER
behavior, the AER behavior after this patch, and the DPC behavior:
AER AER DPC
previous new behavior
-------- --- --------
Log error yes yes yes (minimal)
drv.error_detected() yes no no
Reset Link yes yes yes
drv.mmio_enabled() yes no no
drv.slot_reset() yes no no
drv.resume() yes no no
Remove PCI devices no yes yes
(calls drv.remove())
Re-enumerate no yes yes
(calls drv.probe())
N.B. With DPC, the Link reset happens before the driver .remove() calls,
while with AER, the reset happens *after* the .remove() calls. The goal is
to eventually do the reset before .remove() for AER as well.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
[bhelgaas: changelog, squash doc patch into this, remove unused
"result_data"]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Clients such as hotplug and Downstream Port Containment (DPC) both need to
wait until a link becomes active or inactive.
Add a generic pcie_wait_link_active() interface and use it instead of
duplicating the code.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
The generic IRQ handling code ensures that an interrupt handler runs with
its interrupt masked or disabled. If the interrupt is level-triggered, the
interrupt handler must tell its device to stop asserting the interrupt
before returning. If it doesn't, we will immediately take the interrupt
again when the handler returns and the generic code unmasks the interrupt.
The driver doesn't know whether its interrupt is edge- or level-triggered,
so it must clear its interrupt source directly in its interrupt handler.
Previously we cleared the DPC interrupt status in the bottom half, i.e., in
deferred work, which can cause an interrupt storm if the DPC interrupt
happens to be level-triggered, e.g., if we're using INTx instead of MSI.
Clear the DPC interrupt status bit in the interrupt handler, not in the
deferred work.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Reviewed-by: Keith Busch <keith.busch@intel.com>
When a PCIe AER error occurs, the TLP header information is printed in the
kernel message but it is missing from the tracepoint. A userspace program
can use this information in the tracepoint to better analyze problems.
To enable the tracepoint:
echo 1 > /sys/kernel/debug/tracing/events/ras/aer_event/enable
Example tracepoint output:
$ cat /sys/kernel/debug/tracing/trace
aer_event: 0000:01:00.0
PCIe Bus Error: severity=Uncorrected, non-fatal, Completer Abort
TLP Header={0x0,0x1,0x2,0x3}
Signed-off-by: Thomas Tai <thomas.tai@oracle.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
AER errors can be reported natively (Linux AER driver fields interrupts and
reads error state directly from hardware) or via the ACPI/APEI/GHES/CPER
path (platform firmware reads error state from hardware and sends it to
Linux via ACPI interfaces).
Previously the same error would produce different output depending on
whether it was reported natively or via ACPI. The CPER path resulted in
hard-to-understand messages, without a prefix. Instead use
__aer_print_error() for both native AER and CPER to provide a more
consistent log format.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
02bfeb4842 ("PCI/portdrv: Simplify PCIe feature permission checking")
removed the only call of pcie_port_acpi_setup() and removed portdrv_acpi.o
from the Makefile, but I forgot to remove pcie_port_acpi_setup() itself.
Remove pcie_port_acpi_setup() and the drivers/pci/pcie/portdrv_acpi.c file.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When in the ASPM L1.0 state (but not the PCI-PM L1.0 state), the most
recent LTR value and the LTR_L1.2_THRESHOLD determines whether the link
enters the L1.2 substate.
If we don't have LTR enabled, prevent the use of ASPM L1.2.
PCI-PM L1.2 may still be used because it doesn't depend on
LTR_L1.2_THRESHOLD (see PCIe r4.0, sec 5.5.1).
Tested-by: Srinath Mannam <srinath.mannam@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- move pcieport_if.h to drivers/pci/pcie/ to encapsulate it (Frederick
Lawler)
- merge pcieport_if.h into portdrv.h (Bjorn Helgaas)
- move workaround for BIOS PME issue from portdrv to PCI core (Bjorn
Helgaas)
- completely disable portdrv with "pcie_ports=compat" (Bjorn Helgaas)
- remove portdrv link order dependency (Bjorn Helgaas)
- remove support for unused VC portdrv service (Bjorn Helgaas)
- simplify portdrv feature permission checking (Bjorn Helgaas)
- remove "pcie_hp=nomsi" parameter (use "pci=nomsi" instead) (Bjorn
Helgaas)
- remove unnecessary "pcie_ports=auto" parameter (Bjorn Helgaas)
- use cached AER capability offset (Frederick Lawler)
- don't enable DPC if BIOS hasn't granted AER control (Mika Westerberg)
- rename pcie-dpc.c to dpc.c (Bjorn Helgaas)
* pci/portdrv:
PCI/DPC: Rename from pcie-dpc.c to dpc.c
PCI/DPC: Do not enable DPC if AER control is not allowed by the BIOS
PCI/AER: Use cached AER Capability offset
PCI/portdrv: Rename and reverse sense of pcie_ports_auto
PCI/portdrv: Encapsulate pcie_ports_auto inside the port driver
PCI/portdrv: Remove unnecessary "pcie_ports=auto" parameter
PCI/portdrv: Remove "pcie_hp=nomsi" kernel parameter
PCI/portdrv: Remove unnecessary include of <linux/pci-aspm.h>
PCI/portdrv: Simplify PCIe feature permission checking
PCI/portdrv: Remove unused PCIE_PORT_SERVICE_VC
PCI/portdrv: Remove pcie_port_bus_type link order dependency
PCI/portdrv: Disable port driver in compat mode
PCI/PM: Clear PCIe PME Status bit for Root Complex Event Collectors
PCI/PM: Clear PCIe PME Status bit in core, not PCIe port driver
PCI/PM: Move pcie_clear_root_pme_status() to core
PCI/portdrv: Merge pcieport_if.h into portdrv.h
PCI/portdrv: Move pcieport_if.h to drivers/pci/pcie/
Conflicts:
drivers/pci/pcie/Makefile
drivers/pci/pcie/portdrv.h
- use PCI_EXP_DEVCTL2_COMP_TIMEOUT in rapidio/tsi721 (Bjorn Helgaas)
- remove possible NULL pointer dereference in of_pci_bus_find_domain_nr()
(Shawn Lin)
- report quirk timings with dev_info (Bjorn Helgaas)
- report quirks that take longer than 10ms (Bjorn Helgaas)
- add and use Altera Vendor ID (Johannes Thumshirn)
- tidy Makefiles and comments (Bjorn Helgaas)
* pci/misc:
PCI: Always define the of_node helpers
PCI: Tidy comments
PCI: Tidy Makefiles
mcb: Add Altera PCI ID to mcb-pci
PCI: Add Altera vendor ID
PCI: Report quirks that take more than 10ms
PCI: Report quirk timings with pci_info() instead of pr_debug()
PCI: Fix NULL pointer dereference in of_pci_bus_find_domain_nr()
rapidio/tsi721: use PCI_EXP_DEVCTL2_COMP_TIMEOUT macro
Rename pcie-dpc.c to dpc.c. The path "drivers/pci/pcie/pcie-dpc.c" has
more occurrences of "pci" than necessary.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Commit eed85ff4c0 ("PCI/DPC: Enable DPC only if AER is available") made
DPC control dependent whether AER is enabled in the OS. However, it does
not take into account situations where BIOS has not given OS control of
AER:
acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
acpi PNP0A08:00: _OSC: platform does not support [AER]
acpi PNP0A08:00: _OSC: OS now controls [PCIeHotplug PME PCIeCapability]
I think here it is better not to enable DPC even if the capability is
available because then it would be against what "Determination of DPC
Control" note in PCIe 4.0 sec 6.1.10 recommends.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Replace pci_find_ext_capability(..., PCI_EXT_CAP_ID_ERR) calls with
pci_dev->aer_cap.
pci_dev->aer_cap is initialized in pci_init_capabilities(), which happens
before any of these users of the AER Capability.
Signed-off-by: Frederick Lawler <fred@fredlawl.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The platform may restrict the OS's use of PCIe services, e.g., via the ACPI
_OSC method. The user may use "pcie_ports=native" to force the port driver
to use PCIe services even if the platform asked us not to.
The "pcie_ports=native" parameter determines the setting of
pcie_ports_auto. Rename this to pcie_ports_native and reverse the
sense to simplify the code.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
"pcie_ports_auto" is only used inside the PCIe port driver itself, so
move it from include/linux/pci.h to portdrv.h so it's not visible to the
whole kernel.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The "pcie_ports=auto" parameter set pcie_ports_disabled and pcie_ports_auto
to their compiled-in defaults, so specifying the parameter is the same as
not using it at all.
Remove the "pcie_ports=auto" parameter and update the documentation.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
7570a333d8 ("PCI: Add pcie_hp=nomsi to disable MSI/MSI-X for pciehp
driver") added the "pcie_hp=nomsi" kernel parameter to work around this
error on shutdown:
irq 16: nobody cared (try booting with the "irqpoll" option)
Pid: 1081, comm: reboot Not tainted 3.2.0 #1
...
Disabling IRQ #16
This happened on an unspecified system (possibly involving the Integrated
Device Technology, Inc. Device 807f bridge) where "an un-wanted interrupt
is generated when PCI driver switches from MSI/MSI-X to INTx while shutting
down the device."
The implication was that the device was buggy, but it is normal for a
device to use INTx after MSI/MSI-X have been disabled. The only problem
was that the driver was still attached and it wasn't prepared for INTx
interrupts. Prarit Bhargava fixed this issue with fda78d7a0e ("PCI/MSI:
Stop disabling MSI/MSI-X in pci_device_shutdown()").
There is no automated way to set this parameter, so it's not very useful
for distributions or end users. It's really only useful for debugging, and
we have "pci=nomsi" for that purpose.
Revert 7570a333d8 to remove the "pcie_hp=nomsi" parameter.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
CC: MUNEDA Takahiro <muneda.takahiro@jp.fujitsu.com>
CC: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
CC: Prarit Bhargava <prarit@redhat.com>
portdrv_pci.c doesn't use anything from <linux/pci-aspm.h>. Remove the
include of it. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some PCIe features (AER, DPC, hotplug, PME) can be managed by either the
platform firmware or the OS, so the host bridge driver may have to request
permission from the platform before using them. On ACPI systems, this is
done by negotiate_os_control() in acpi_pci_root_add().
The PCIe port driver later uses pcie_port_platform_notify() and
pcie_port_acpi_setup() to figure out whether it can use these features.
But all we need is a single bit for each service, so these interfaces are
needlessly complicated.
Simplify this by adding bits in the struct pci_host_bridge to show when the
OS has permission to use each feature:
+ unsigned int native_aer:1; /* OS may use PCIe AER */
+ unsigned int native_hotplug:1; /* OS may use PCIe hotplug */
+ unsigned int native_pme:1; /* OS may use PCIe PME */
These are set when we create a host bridge, and the host bridge driver can
clear the bits corresponding to any feature the platform doesn't want us to
use.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
No driver registers for PCIE_PORT_SERVICE_VC, so remove it.
This removes the VC "service" files from /sys/bus/pci_express/devices,
e.g., 0000:07:00.0:pcie108, 0000:08:04.0:pcie208 (all the files that
contained "8" as the last digit of the "pcieXXX" part). The port driver
created these files for PCIe port devices that have a VC Capability.
Since this reduces PCIE_PORT_DEVICE_MAXSERVICES and moves DPC down into the
spot where VC used to be, the DPC sysfs files will now be named "pcieXX8".
I don't think there's anything useful userspace can do with those files, so
I hope nobody cares about these filenames.
There is no VC driver that calls pcie_port_service_register(), so there
never was a /sys/bus/pci_express/drivers/vc directory.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
The pcie_port_bus_type must be registered before drivers that depend on it
can be registered. Those drivers include:
pcied_init() # PCIe native hotplug driver
aer_service_init() # AER driver
dpc_service_init() # DPC driver
pcie_pme_service_init() # PME driver
Previously we registered pcie_port_bus_type from pcie_portdrv_init(), a
device_initcall. The callers of pcie_port_service_register() (above) are
also device_initcalls. This is fragile because the device_initcall
ordering depends on link order, which is not explicit.
Register pcie_port_bus_type from pci_driver_init() along with pci_bus_type.
This removes the link order dependency between portdrv and the pciehp, AER,
DPC, and PCIe PME drivers.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
The "pcie_ports=compat" kernel parameter sets pcie_ports_disabled, which is
intended to disable the PCIe port driver. But even when it was disabled,
we registered pcie_portdriver so we could work around a BIOS PME issue (see
fe31e69740 ("PCI/PCIe: Clear Root PME Status bits early during system
resume")).
Registering the driver meant that the pcie_portdrv_probe() path called
pci_enable_device(), pci_save_state(), pm_runtime_set_autosuspend_delay(),
pm_runtime_use_autosuspend(), etc., even when the driver was disabled.
We've since moved the BIOS PME workaround from the port driver to the core,
so stop registering the PCIe port driver in compat mode.
This means "pcie_ports=compat" will now be basically the same as turning
off CONFIG_PCIEPORTBUS completely.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Remove pointless comments that tell us the file name, remove blank line
comments, follow multi-line comment conventions. No functional change
intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Indent things so they line up neatly and remove extra blank lines and
superfluous comments. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
fe31e69740 ("PCI/PCIe: Clear Root PME Status bits early during system
resume") added a .resume_noirq() callback to the PCIe port driver to clear
the PME Status bit during resume to work around a BIOS issue.
The BIOS evidently enabled PME interrupts for ACPI-based runtime wakeups
but did not clear the PME Status bit during resume, which meant PMEs after
resume did not trigger interrupts because PME Status did not transition
from cleared to set.
The fix was in the PCIe port driver, so it worked when CONFIG_PCIEPORTBUS
was set. But I think we *always* want the fix because the platform may use
PME interrupts even if Linux is built without the PCIe port driver.
Move the fix from the port driver to the PCI core so we can work around
this "PME doesn't work after waking from a sleep state" issue regardless of
CONFIG_PCIEPORTBUS.
[bhelgaas: folded in warning fix from Arnd Bergmann <arnd@arndb.de>:
https://lkml.kernel.org/r/20180328134747.2062348-1-arnd@arndb.de]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Move pcie_clear_root_pme_status() from the port driver to the PCI core so
it will be available even when the port driver isn't present. No
functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
pcieport_if.h contained the interfaces to register port service driver,
e.g., pcie_port_service_register(). portdrv.h contained internal data
structures of the port driver.
I don't think it's worth keeping those files separate, since both headers
and their users are all inside the PCI core.
Merge pcieport_if.h directly in drivers/pci/pcie/portdrv.h and update the
users to include that instead.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Previously we emitted a warning if we tried to configure common clock mode
the link was already configured to common clock mode by the UEFI BIOS.
Bail out silently in that case instead of emitting the warning:
pci 0004:00:00.0: ASPM: Could not configure common clock
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
aspm_calc_l1ss_info() computes l1_2_threshold in microseconds as:
l1_2_threshold = 2 + 4 + t_common_mode + t_power_on;
where t_common_mode is at most 255us:
PCI_L1SS_CAP_CM_RESTORE_TIME 0x0000ff00 <-- 8 bits; <256us
and t_power_on is at most 31 * 100us = 3100us:
PCI_L1SS_CAP_P_PWR_ON_VALUE 0x00f80000 <-- 5 bits; <32
PCI_L1SS_CAP_P_PWR_ON_SCALE 0x00030000 <-- *2us, *10us, or *100us
So l1_2_threshold is at most 2 + 4 + 255 + 3100 = 3361, which means
threshold_ns is at most 3361 * 1000 = 3361000, which easily fits in a
u32.
Declare threshold_ns as u32, not u64. This fixes a Coverity warning.
Addresses-Coverity-ID: 1462501
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Move pcieport_if.h from include/linux to drivers/pci/pcie/pcieport_if.h
because the interfaces there are only used by the PCI core.
Replace all uses of #include<linux/pcieport_if.h> with relative paths to
the new file location, e.g., #include "../pcieport_if.h"
Signed-off-by: Frederick Lawler <fred@fredlawl.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ttq9
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- skip AER driver error recovery callbacks for correctable errors
reported via ACPI APEI, as we already do for errors reported via the
native path (Tyler Baicar)
- fix DPC shared interrupt handling (Alex Williamson)
- print full DPC interrupt number (Keith Busch)
- enable DPC only if AER is available (Keith Busch)
- simplify DPC code (Bjorn Helgaas)
- calculate ASPM L1 substate parameter instead of hardcoding it (Bjorn
Helgaas)
- enable Latency Tolerance Reporting for ASPM L1 substates (Bjorn
Helgaas)
- move ASPM internal interfaces out of public header (Bjorn Helgaas)
- allow hot-removal of VGA devices (Mika Westerberg)
- speed up unplug and shutdown by assuming Thunderbolt controllers
don't support Command Completed events (Lukas Wunner)
- add AtomicOps support for GPU and Infiniband drivers (Felix Kuehling,
Jay Cornwall)
- expose "ari_enabled" in sysfs to help NIC naming (Stuart Hayes)
- clean up PCI DMA interface usage (Christoph Hellwig)
- remove PCI pool API (replaced with DMA pool) (Romain Perier)
- deprecate pci_get_bus_and_slot(), which assumed PCI domain 0 (Sinan
Kaya)
- move DT PCI code from drivers/of/ to drivers/pci/ (Rob Herring)
- add PCI-specific wrappers for dev_info(), etc (Frederick Lawler)
- remove warnings on sysfs mmap failure (Bjorn Helgaas)
- quiet ROM validation messages (Alex Deucher)
- remove redundant memory alloc failure messages (Markus Elfring)
- fill in types for compile-time VGA and other I/O port resources
(Bjorn Helgaas)
- make "pci=pcie_scan_all" work for Root Ports as well as Downstream
Ports to help AmigaOne X1000 (Bjorn Helgaas)
- add SPDX tags to all PCI files (Bjorn Helgaas)
- quirk Marvell 9128 DMA aliases (Alex Williamson)
- quirk broken INTx disable on Ceton InfiniTV4 (Bjorn Helgaas)
- fix CONFIG_PCI=n build by adding dummy pci_irqd_intx_xlate() (Niklas
Cassel)
- use DMA API to get MSI address for DesignWare IP (Niklas Cassel)
- fix endpoint-mode DMA mask configuration (Kishon Vijay Abraham I)
- fix ARTPEC-6 incorrect IS_ERR() usage (Wei Yongjun)
- add support for ARTPEC-7 SoC (Niklas Cassel)
- add endpoint-mode support for ARTPEC (Niklas Cassel)
- add Cadence PCIe host and endpoint controller driver (Cyrille
Pitchen)
- handle multiple INTx status bits being set in dra7xx (Vignesh R)
- translate dra7xx hwirq range to fix INTD handling (Vignesh R)
- remove deprecated Exynos PHY initialization code (Jaehoon Chung)
- fix MSI erratum workaround for HiSilicon Hip06/Hip07 (Dongdong Liu)
- fix NULL pointer dereference in iProc BCMA driver (Ray Jui)
- fix Keystone interrupt-controller-node lookup (Johan Hovold)
- constify qcom driver structures (Julia Lawall)
- rework Tegra config space mapping to increase space available for
endpoints (Vidya Sagar)
- simplify Tegra driver by using bus->sysdata (Manikanta Maddireddy)
- remove PCI_REASSIGN_ALL_BUS usage on Tegra (Manikanta Maddireddy)
- add support for Global Fabric Manager Server (GFMS) event to
Microsemi Switchtec switch driver (Logan Gunthorpe)
- add IDs for Switchtec PSX 24xG3 and PSX 48xG3 (Kelvin Cao)
* tag 'pci-v4.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (140 commits)
PCI: cadence: Add EndPoint Controller driver for Cadence PCIe controller
dt-bindings: PCI: cadence: Add DT bindings for Cadence PCIe endpoint controller
PCI: endpoint: Fix EPF device name to support multi-function devices
PCI: endpoint: Add the function number as argument to EPC ops
PCI: cadence: Add host driver for Cadence PCIe controller
dt-bindings: PCI: cadence: Add DT bindings for Cadence PCIe host controller
PCI: Add vendor ID for Cadence
PCI: Add generic function to probe PCI host controllers
PCI: generic: fix missing call of pci_free_resource_list()
PCI: OF: Add generic function to parse and allocate PCI resources
PCI: Regroup all PCI related entries into drivers/pci/Makefile
PCI/DPC: Reformat DPC register definitions
PCI/DPC: Add and use DPC Status register field definitions
PCI/DPC: Squash dpc_rp_pio_get_info() into dpc_process_rp_pio_error()
PCI/DPC: Remove unnecessary RP PIO register structs
PCI/DPC: Push dpc->rp_pio_status assignment into dpc_rp_pio_get_info()
PCI/DPC: Squash dpc_rp_pio_print_error() into dpc_rp_pio_get_info()
PCI/DPC: Make RP PIO log size check more generic
PCI/DPC: Rename local "status" to "dpc_status"
PCI/DPC: Squash dpc_rp_pio_print_tlp_header() into dpc_rp_pio_print_error()
...
Highlights:
- Enable support for memory protection keys aka "pkeys" on Power7/8/9 when
using the hash table MMU.
- Extend our interrupt soft masking to support masking PMU interrupts as well
as "normal" interrupts, and then use that to implement local_t for a ~4x
speedup vs the current atomics-based implementation.
- A new driver "ocxl" for "Open Coherent Accelerator Processor Interface
(OpenCAPI)" devices.
- Support for new device tree properties on PowerVM to describe hotpluggable
memory and devices.
- Add support for CLOCK_{REALTIME/MONOTONIC}_COARSE to the 64-bit VDSO.
- Freescale updates from Scott:
"Contains fixes for CPM GPIO and an FSL PCI erratum workaround, plus a
minor cleanup patch."
As well as quite a lot of other changes all over the place, and small fixes and
cleanups as always.
Thanks to:
Alan Modra, Alastair D'Silva, Alexey Kardashevskiy, Alistair Popple, Andreas
Schwab, Andrew Donnellan, Aneesh Kumar K.V, Anju T Sudhakar, Anshuman
Khandual, Anton Blanchard, Arnd Bergmann, Balbir Singh, Benjamin
Herrenschmidt, Bhaktipriya Shridhar, Bryant G. Ly, Cédric Le Goater,
Christophe Leroy, Christophe Lombard, Cyril Bur, David Gibson, Desnes A. Nunes
do Rosario, Dmitry Torokhov, Frederic Barrat, Geert Uytterhoeven, Guilherme G.
Piccoli, Gustavo A. R. Silva, Gustavo Romero, Ivan Mikhaylov, Joakim
Tjernlund, Joe Perches, Josh Poimboeuf, Juan J. Alvarez, Julia Cartwright,
Kamalesh Babulal, Madhavan Srinivasan, Mahesh Salgaonkar, Mathieu Malaterre,
Michael Bringmann, Michael Hanselmann, Michael Neuling, Nathan Fontenot,
Naveen N. Rao, Nicholas Piggin, Paul Mackerras, Philippe Bergheaud, Ram Pai,
Russell Currey, Santosh Sivaraj, Scott Wood, Seth Forshee, Simon Guo, Stewart
Smith, Sukadev Bhattiprolu, Thiago Jung Bauermann, Vaibhav Jain, Vasyl
Gomonovych.
-----BEGIN PGP SIGNATURE-----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=3rYn
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Highlights:
- Enable support for memory protection keys aka "pkeys" on Power7/8/9
when using the hash table MMU.
- Extend our interrupt soft masking to support masking PMU interrupts
as well as "normal" interrupts, and then use that to implement
local_t for a ~4x speedup vs the current atomics-based
implementation.
- A new driver "ocxl" for "Open Coherent Accelerator Processor
Interface (OpenCAPI)" devices.
- Support for new device tree properties on PowerVM to describe
hotpluggable memory and devices.
- Add support for CLOCK_{REALTIME/MONOTONIC}_COARSE to the 64-bit
VDSO.
- Freescale updates from Scott: fixes for CPM GPIO and an FSL PCI
erratum workaround, plus a minor cleanup patch.
As well as quite a lot of other changes all over the place, and small
fixes and cleanups as always.
Thanks to: Alan Modra, Alastair D'Silva, Alexey Kardashevskiy,
Alistair Popple, Andreas Schwab, Andrew Donnellan, Aneesh Kumar K.V,
Anju T Sudhakar, Anshuman Khandual, Anton Blanchard, Arnd Bergmann,
Balbir Singh, Benjamin Herrenschmidt, Bhaktipriya Shridhar, Bryant G.
Ly, Cédric Le Goater, Christophe Leroy, Christophe Lombard, Cyril Bur,
David Gibson, Desnes A. Nunes do Rosario, Dmitry Torokhov, Frederic
Barrat, Geert Uytterhoeven, Guilherme G. Piccoli, Gustavo A. R. Silva,
Gustavo Romero, Ivan Mikhaylov, Joakim Tjernlund, Joe Perches, Josh
Poimboeuf, Juan J. Alvarez, Julia Cartwright, Kamalesh Babulal,
Madhavan Srinivasan, Mahesh Salgaonkar, Mathieu Malaterre, Michael
Bringmann, Michael Hanselmann, Michael Neuling, Nathan Fontenot,
Naveen N. Rao, Nicholas Piggin, Paul Mackerras, Philippe Bergheaud,
Ram Pai, Russell Currey, Santosh Sivaraj, Scott Wood, Seth Forshee,
Simon Guo, Stewart Smith, Sukadev Bhattiprolu, Thiago Jung Bauermann,
Vaibhav Jain, Vasyl Gomonovych"
* tag 'powerpc-4.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (199 commits)
powerpc/mm/radix: Fix build error when RADIX_MMU=n
macintosh/ams-input: Use true and false for boolean values
macintosh: change some data types from int to bool
powerpc/watchdog: Print the NIP in soft_nmi_interrupt()
powerpc/watchdog: regs can't be null in soft_nmi_interrupt()
powerpc/watchdog: Tweak watchdog printks
powerpc/cell: Remove axonram driver
rtc-opal: Fix handling of firmware error codes, prevent busy loops
powerpc/mpc52xx_gpt: make use of raw_spinlock variants
macintosh/adb: Properly mark continued kernel messages
powerpc/pseries: Fix cpu hotplug crash with memoryless nodes
powerpc/numa: Ensure nodes initialized for hotplug
powerpc/numa: Use ibm,max-associativity-domains to discover possible nodes
powerpc/kernel: Block interrupts when updating TIDR
powerpc/powernv/idoa: Remove unnecessary pcidev from pci_dn
powerpc/mm/nohash: do not flush the entire mm when range is a single page
powerpc/pseries: Add Initialization of VF Bars
powerpc/pseries/pci: Associate PEs to VFs in configure SR-IOV
powerpc/eeh: Add EEH notify resume sysfs
powerpc/eeh: Add EEH operations to notify resume
...
* pci/spdx:
PCI: Add SPDX GPL-2.0+ to replace implicit GPL v2 or later statement
PCI: Add SPDX GPL-2.0+ to replace GPL v2 or later boilerplate
PCI: Add SPDX GPL-2.0 to replace COPYING boilerplate
PCI: Add SPDX GPL-2.0 to replace GPL v2 boilerplate
PCI: Add SPDX GPL-2.0 when no license was specified
* pci/misc:
PCI: Add dummy pci_irqd_intx_xlate() for CONFIG_PCI=n build
PCI: Add wrappers for dev_printk()
PCI: Remove unnecessary messages for memory allocation failures
PCI: Add #defines for Completion Timeout Disable feature
hinic: Replace PCI pool old API
net: e100: Replace PCI pool old API
block: DAC960: Replace PCI pool old API
MAINTAINERS: Include more PCI files
PCI: Remove unneeded kallsyms include
powerpc/pci: Unroll two pass loop when scanning bridges
powerpc/pci: Use for_each_pci_bridge() helper
* pci/dpc:
PCI/DPC: Reformat DPC register definitions
PCI/DPC: Add and use DPC Status register field definitions
PCI/DPC: Squash dpc_rp_pio_get_info() into dpc_process_rp_pio_error()
PCI/DPC: Remove unnecessary RP PIO register structs
PCI/DPC: Push dpc->rp_pio_status assignment into dpc_rp_pio_get_info()
PCI/DPC: Squash dpc_rp_pio_print_error() into dpc_rp_pio_get_info()
PCI/DPC: Make RP PIO log size check more generic
PCI/DPC: Rename local "status" to "dpc_status"
PCI/DPC: Squash dpc_rp_pio_print_tlp_header() into dpc_rp_pio_print_error()
PCI/DPC: Process RP PIO details only if RP PIO extensions supported
PCI/DPC: Read RP PIO Log Size once at probe
PCI/DPC: Rename struct dpc_dev.rp to rp_extensions
PCI/DPC: Add local variable for DPC capability offset
PCI/DPC: Rename interrupt_event_handler() to dpc_work()
PCI/DPC: Fix interrupt message number print
PCI/DPC: Enable DPC only if AER is available
PCI/DPC: Fix shared interrupt handling
Add definitions for DPC Status register fields and use them in the code.
No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sinan Kaya <okaya@codeaurora.org>
dpc_process_rp_pio_error() only calls dpc_rp_pio_get_info(), so squash them
together. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sinan Kaya <okaya@codeaurora.org>
We read and immediately print the RP PIO log registers. We don't save
them, so there's no need to define structs for them. Remove the structs
and read the registers into local variables instead. No functional change
intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sinan Kaya <okaya@codeaurora.org>
Move the dpc->rp_pio_status assignment into dpc_rp_pio_get_info() since
that's where we read rp_pio->status anway. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sinan Kaya <okaya@codeaurora.org>
Separating dpc_rp_pio_print_error() doesn't really provide any useful
abstraction, so squash it into its caller, dpc_rp_pio_get_info(). No
functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sinan Kaya <okaya@codeaurora.org>
In dpc_probe(), we set dpc->rp_log_size to zero if we think the hardware
reports an invalid size. In this case, we could have dpc->rp_extensions
set but dpc->rp_log_size == 0, and we should print the basic RP PIO
registers but not the variable-size portion. We already checked for
dpc->rp_log_size < 4 above, so this patch is just for consistency of style.
No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sinan Kaya <okaya@codeaurora.org>
In dpc_rp_pio_get_info() rename the local "status" variable to
"dpc_status". This is to make room for another variable named "status" in
a subsequent patch. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sinan Kaya <okaya@codeaurora.org>
Separating dpc_rp_pio_print_tlp_header() doesn't really provide any useful
abstraction, so squash it into its caller, dpc_rp_pio_print_error(). No
functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sinan Kaya <okaya@codeaurora.org>
The RP PIO registers (status, mask, severity, etc) are only implemented if
the "RP Extensions for DPC" bit is set in the DPC Capabilities register.
Previously we called dpc_process_rp_pio_error(), which reads and decodes
those RP PIO registers, whenever the DPC Status register indicated an "RP
PIO error" (Trigger Reason == 3 and Trigger Reason Extension == 0).
It does seem reasonable to assume that DPC Status would only indicate an RP
PIO error if the RP extensions are supported, but PCIe r4.0, sec 7.9.15.4,
is actually not explicit about that: it does not say "Trigger Reason
Extension == 0 is valid only for Root Ports that support RP Extensions for
DPC."
Check whether the RP Extensions for DPC are supported before trying to read
the RP PIO registers.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sinan Kaya <okaya@codeaurora.org>
The RP PIO Log Size is a read-only field in the DPC Capability, so it is
constant and known at probe-time, but previously we read it every time we
processed an RP PIO error.
Read it once in dpc_probe() (if the RP Extensions for DPC are supported)
and remember the size in struct dpc_dev. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sinan Kaya <okaya@codeaurora.org>
"rp" is ambiguous: it might mean "this DPC device is a Root Port." But in
fact, it means "this DPC device is a Root Port *and* it supports a set of
DPC Extensions."
Rename "rp" to "rp_extensions" to make this more clear. No functional
change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sinan Kaya <okaya@codeaurora.org>
Add a local variable for DPC capability offset and replace repeated use of
"dpc->cap_pos" with simply "cap". No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sinan Kaya <okaya@codeaurora.org>
Add SPDX GPL-2.0 to all PCI files that referred to the kernel default
"COPYING" file, which specifies GPL version 2.
Remove the boilerplate language referring to the GPL and "COPYING", relying
on the assertion in b24413180f ("License cleanup: add SPDX GPL-2.0
license identifier to files with no license") that the SPDX identifier may
be used instead of the full boilerplate text.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX GPL-2.0 to all PCI files that specified the GPL version 2 license.
Remove the boilerplate GPL version 2 language, relying on the assertion in
b24413180f ("License cleanup: add SPDX GPL-2.0 license identifier to
files with no license") that the SPDX identifier may be used instead of the
full boilerplate text.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Devices can go offline when erors reported. This patch adds a change
to the kernel object and lets udev know of error. When device resumes,
a change is also set reporting device as online. Therefore, EEH and
AER events are better propagated to user space for PCI devices in all
arches.
Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Signed-off-by: Juan J. Alvarez <jjalvare@linux.vnet.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Rename interrupt_event_handler() to dpc_work() so there's more useful
information in stack traces and similar situations. No functional change
intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sinan Kaya <okaya@codeaurora.org>
The interrupt message number is the first 5 bits, but the driver was
masking only the first 4 bits. Fix that by using the existing
define.
Signed-off-by: Keith Busch <keith.busch@intel.com>
[bhelgaas: remove reformatting (done by another patch)]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The "Determination of DPC Control" implementation note in PCIe r4.0, sec
6.1.10, recommends the operating system always link DPC control to the
control of AER, as the two functionalities are strongly connected.
To avoid conflicts over whether platform firmware or the OS controls DPC,
enable DPC only if AER is enabled in the OS, and the device's error
handling does not have firmware-first AER handling.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
b24413180f ("License cleanup: add SPDX GPL-2.0 license identifier to
files with no license") added SPDX GPL-2.0 to several PCI files that
previously contained no license information.
Add SPDX GPL-2.0 to all other PCI files that did not contain any license
information and hence were under the default GPL version 2 license of the
kernel.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add PCI-specific dev_printk() wrappers and use them to simplify the code
slightly. No functional change intended.
Signed-off-by: Frederick Lawler <fred@fredlawl.com>
[bhelgaas: squash into one patch]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
get_device_error_info() reads error information from registers in the AER
capability. If we call it for a device that has no AER capability, it
should return an error, but previously it returned success.
Return 0 (error) if the device doesn't have an AER capability.
Signed-off-by: Keith Busch <keith.busch@intel.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
DPC supports shared interrupts, but it plays very loosely with testing
whether the interrupt is generated by DPC before generating spurious log
messages, such as:
dpc 0000:10:01.2:pcie010: DPC containment event, status:0x1f00 source:0x0000
Testing the status register for zero or -1 is not sufficient when the
device supports the RP PIO First Error Pointer register. Change this to
test whether the interrupt is enabled in the control register, retaining
the device present test, and that the status reports the interrupt as
signaled and DPC is triggered, clearing as a spurious interrupt otherwise.
Additionally, since the interrupt is actually serviced by a workqueue,
disable the interrupt in the control register until that completes or else
we may never see it execute due to further incoming interrupts. A software
generated DPC floods the system otherwise.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Make the PCIe port driver set DPM_FLAG_SMART_SUSPEND and
DPM_FLAG_LEAVE_SUSPENDED for the devices handled by it to benefit
from the opportunistic optimizations in the PCI layer enabled by
these flags.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Per PCIe r3.1, sec 5.5.1, LTR_L1.2_THRESHOLD determines whether we enter
the L1.2 Link state: if L1.2 is enabled and downstream devices have
reported that they can tolerate latency of at least LTR_L1.2_THRESHOLD, we
must enter L1.2 when CLKREQ# is de-asserted.
The implication is that LTR_L1.2_THRESHOLD is the time required to
transition the Link from L0 to L1.2 and back to L0, and per sec 5.5.3.3.1,
Figures 5-16 and 5-17, it appears that the absolute minimum time for those
transitions would be T(POWER_OFF) + T(L1.2) + T(POWER_ON) + T(COMMONMODE).
Therefore, compute LTR_L1.2_THRESHOLD as:
2us T(POWER_OFF)
+ 4us T(L1.2)
+ T(POWER_ON)
+ T(COMMONMODE)
= LTR_L1.2_THRESHOLD
Previously we set LTR_L1.2_THRESHOLD to a fixed value of 163840ns
(163.84us):
#define LTR_L1_2_THRESHOLD_BITS ((1 << 21) | (1 << 23) | (1 << 30))
((1 << 21) | (1 << 23) | (1 << 30)) = 0x40a00000
LTR_L1.2_THRESHOLD_Value = (0x40a00000 & 0x03ff0000) >> 16 = 0xa0 = 160
LTR_L1.2_THRESHOLD_Scale = (0x40a00000 & 0xe0000000) >> 29 = 0x2 (* 1024ns)
LTR_L1.2_THRESHOLD = 160 * 1024ns = 163840ns
Obviously this doesn't account for the circuit characteristics of different
implementations.
Note that while firmware may enable LTR, Linux itself currently does not
enable LTR. When L1.2 is enabled but LTR is not, LTR_L1.2_THRESHOLD is
ignored and we always enter L1.2 when it is enabled and CLKREQ# is
de-asserted. So this patch should not have any effect unless firmware
enables LTR.
Fixes: f1f0366dd6 ("PCI/ASPM: Calculate and save the L1.2 timing parameters")
Link: https://www.coreboot.org/pipermail/coreboot-gerrit/2015-March/021134.html
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
Cc: Kenji Chen <kenji.chen@intel.com>
Cc: Patrick Georgi <pgeorgi@google.com>
Cc: Rajat Jain <rajatja@google.com>
PCIe correctable errors are corrected by hardware. Software may log them,
but no other software intervention is required.
There are two paths to enter the AER recovery code: (1) the native path
where Linux fields the AER interrupt and reads the AER registers directly,
and (2) the ACPI path where firmware reads the AER registers and hands them
off to Linux via the ACPI APEI path.
The AER do_recovery() function calls driver error reporting callbacks
(error_detected(), mmio_enabled(), resume(), etc), attempts recovery (for
fatal errors), and logs a "AER: Device recovery successful" message.
Since there's nothing to recover for correctable errors, the native path
already skips do_recovery(), so it doesn't call the driver callbacks and or
emit the message. Make the APEI path do the same.
Signed-off-by: Tyler Baicar <tbaicar@codeaurora.org>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Summary of modules changes for the 4.15 merge window:
- Treewide module_param_call() cleanup, fix up set/get function
prototype mismatches, from Kees Cook
- Minor code cleanups
Signed-off-by: Jessica Yu <jeyu@kernel.org>
-----BEGIN PGP SIGNATURE-----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=c8vb
-----END PGP SIGNATURE-----
Merge tag 'modules-for-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux
Pull module updates from Jessica Yu:
"Summary of modules changes for the 4.15 merge window:
- treewide module_param_call() cleanup, fix up set/get function
prototype mismatches, from Kees Cook
- minor code cleanups"
* tag 'modules-for-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux:
module: Do not paper over type mismatches in module_param_call()
treewide: Fix function prototypes for module_param_call()
module: Prepare to convert all module_param_call() prototypes
kernel/module: Delete an error message for a failed memory allocation in add_module_usage()
* pci/msi:
PCI/portdrv: Compute MSI/MSI-X IRQ vectors after final allocation
PCI/portdrv: Factor out Interrupt Message Number lookup
PCI/portdrv: Consolidate comments
PCI/portdrv: Add #defines for AER and DPC Interrupt Message Number masks
* pci/misc:
PCI: Fix kernel-doc build warning
PCI: Move PCI_QUIRKS to the PCI bus menu
alpha/PCI: Make pdev_save_srm_config() static
PCI: Remove unused declarations
PCI: Remove redundant pci_dev, pci_bus, resource declarations
PCI: Remove redundant pcibios_set_master() declarations
PCI/PME: Handle invalid data when reading Root Status
x86/pci/intel_mid_pci: Constify intel_mid_pci_ops and make it __initconst
PCI: Constify pci_dev_type structure
* pci/aspm:
PCI/ASPM: Add L1 Substates definitions
PCI/ASPM: Reformat ASPM register definitions
PCI/ASPM: Use correct capability pointer to program LTR_L1.2_THRESHOLD
PCI/ASPM: Account for downstream device's Port Common_Mode_Restore_Time
PCI/ASPM: Deal with missing root ports in link state handling
Add and use #defines for L1 Substate register fields instead of hard-coding
the masks. Also update comments to use names from the spec. No functional
change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
Previously we programmed the LTR_L1.2_THRESHOLD in the parent (upstream)
device using the capability pointer of the *child* (downstream) device,
which corrupted some random word of the parent's config space.
Use the parent's L1 SS capability pointer to program its
LTR_L1.2_THRESHOLD.
Fixes: aeda9adeba ("PCI/ASPM: Configure L1 substate settings")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
CC: stable@vger.kernel.org # v4.11+
CC: Rajat Jain <rajatja@google.com>
Every Port that supports the L1.2 substate advertises its Port
Common_Mode_Restore_Time, i.e., the time the Port requires to re-establish
common mode when exiting L1.2 (see PCIe r3.1, sec 7.33.2).
Per sec 5.5.3.3.1, when exiting L1.2, the Downstream Port (the device at
the upstream end of the link) must send TS1 training sequences for at least
T(COMMONMODE) after it detects electrical idle exit on the Link. We want
this to be long enough for both ends of the Link, so we should set it to
the maximum of the Port Common_Mode_Restore_Time for the upstream and
downstream components on the Link.
Previously we only looked at the Port Common_Mode_Restore_Time of the
upstream device, so if the downstream device required more time, we didn't
program the upstream device's T(COMMONMODE) correctly.
Fixes: f1f0366dd6 ("PCI/ASPM: Calculate and save the L1.2 timing parameters")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
Acked-by: Rajat Jain <rajatja@google.com>
CC: stable@vger.kernel.org # v4.11+
PCIe PME and native hotplug share the same interrupt number, so hotplug
interrupts are also processed by PME. In some cases, e.g., a Link Down
interrupt, a device may be present but unreachable, so when we try to
read its Root Status register, the read fails and we get all ones data
(0xffffffff).
Previously, we interpreted that data as PCI_EXP_RTSTA_PME being set, i.e.,
"some device has asserted PME," so we scheduled pcie_pme_work_fn(). This
caused an infinite loop because pcie_pme_work_fn() tried to handle PME
requests until PCI_EXP_RTSTA_PME is cleared, but with the link down,
PCI_EXP_RTSTA_PME can't be cleared.
Check for the invalid 0xffffffff data everywhere we read the Root Status
register.
1469d17dd3 ("PCI: pciehp: Handle invalid data when reading from
non-existent devices") added similar checks in the hotplug driver.
Signed-off-by: Qiang Zheng <zhengqiang10@huawei.com>
[bhelgaas: changelog, also check in pcie_pme_work_fn(), use "~0" to follow
other similar checks]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Some of the PCIe services such as AER are being left enabled during
shutdown. This might cause spurious AER errors while SOC is being powered
down.
Clean up the PCIe services gracefully during shutdown to clear these false
positives.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several function prototypes for the set/get functions defined by
module_param_call() have a slightly wrong argument types. This fixes
those in an effort to clean up the calls when running under type-enforced
compiler instrumentation for CFI. This is the result of running the
following semantic patch:
@match_module_param_call_function@
declarer name module_param_call;
identifier _name, _set_func, _get_func;
expression _arg, _mode;
@@
module_param_call(_name, _set_func, _get_func, _arg, _mode);
@fix_set_prototype
depends on match_module_param_call_function@
identifier match_module_param_call_function._set_func;
identifier _val, _param;
type _val_type, _param_type;
@@
int _set_func(
-_val_type _val
+const char * _val
,
-_param_type _param
+const struct kernel_param * _param
) { ... }
@fix_get_prototype
depends on match_module_param_call_function@
identifier match_module_param_call_function._get_func;
identifier _val, _param;
type _val_type, _param_type;
@@
int _get_func(
-_val_type _val
+char * _val
,
-_param_type _param
+const struct kernel_param * _param
) { ... }
Two additional by-hand changes are included for places where the above
Coccinelle script didn't notice them:
drivers/platform/x86/thinkpad_acpi.c
fs/lockd/svc.c
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
When setting up portdrv MSI/MSI-X interrupts, we previously allocated the
maximum possible number of vectors, read the Interrupt Message Numbers for
each service, saved the IRQ for each, freed the vectors, and finally used
the largest Message Number to reallocate only as many vectors as we need.
The problem is that freeing the vectors invalidates their IRQs, so the
saved IRQ numbers may now be invalid, which can result in errors like
this:
pcie_pme: probe of 0000:00:00.0:pcie001 failed with error -22
pciehp 0000:00:00.0:pcie004: Cannot get irq 20 for the hotplug controller
aer: probe of 0000:00:00.0:pcie002 failed with error -22
dpc 0000:00:00.0:pcie010: request IRQ22 failed: -22
Change the setup so we save the Interrupt Message Numbers (not the IRQs)
before we free the original setup, then use the Message Numbers to compute
the IRQs (via pci_irq_vector()) *after* we reallocate the vectors.
This should always be safe for MSI-X because the Message Numbers are fixed.
For MSI, the hardware is allowed to change Message Numbers when we update
the MSI Multiple Message Enable field when reallocating the vectors, but
since we allocate enough vectors to accommodate the largest Message Number
we found, that's unlikely. See PCIe r3.1, sec 7.8.2, 7.10.10, 7.31.2.
Fixes: 3674cc49da ("PCI/portdrv: Use pci_irq_alloc_vectors()")
Based-on-patch-by: Dongdong Liu <liudongdong3@huawei.com>
Tested-by: Dongdong Liu <liudongdong3@huawei.com> # HiSilicon hip08
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Factor out Interrupt Message Number lookup from the MSI/MSI-X interrupt
setup. One side effect is that we only have to check once to see if we
have enough vectors for all the services. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Consolidate some repetitive comments so we can see the code better. No
functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
In the AER case, the mask isn't strictly necessary because there are no
higher-order bits above the Interrupt Message Number, but using a #define
will make it possible to grep for it.
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Dongdong Liu <liudongdong3@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Even though it is unconventional, some PCIe host implementations omit the
root ports entirely, and simply consist of a host bridge (which is not
modeled as a device in the PCI hierarchy) and a link.
When the downstream device is an endpoint, our current code does not seem
to mind this unusual configuration. However, when PCIe switches are
involved, the ASPM code assumes that any downstream switch port has a
parent, and blindly dereferences the bus->parent->self field of the pci_dev
struct to chain the downstream link state to the link state of the root
port. Given that the root port is missing, the link is not modeled at all,
and nor is the link state, and attempting to access it results in a NULL
pointer dereference and a crash.
Avoid this by allowing the link state chain to terminate at the downstream
port if no root port exists.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously, if an non-fatal error was reported by an endpoint, we
called report_error_detected() for the endpoint, every sibling on the
bus, and their descendents. If any of them did not implement the
.error_detected() method, do_recovery() failed, leaving all these
devices unrecovered.
For example, the system described in the bugzilla below has two devices:
0000:74:02.0 [19e5:a230] SAS controller, driver has .error_detected()
0000:74:03.0 [19e5:a235] SATA controller, driver lacks .error_detected()
When a device such as 74:02.0 reported a non-fatal error, do_recovery()
failed because 74:03.0 lacked an .error_detected() method. But per PCIe
r3.1, sec 6.2.2.2.2, such an error does not compromise the Link and
does not affect 74:03.0:
Non-fatal errors are uncorrectable errors which cause a particular
transaction to be unreliable but the Link is otherwise fully functional.
Isolating Non-fatal from Fatal errors provides Requester/Receiver logic
in a device or system management software the opportunity to recover from
the error without resetting the components on the Link and disturbing
other transactions in progress. Devices not associated with the
transaction in error are not impacted by the error.
Report non-fatal errors only to the endpoint that reported them. We really
want to check for AER_NONFATAL here, but the current code structure doesn't
allow that. Looking for pci_channel_io_normal is the best we can do now.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=197055
Fixes: 6c2b374d74 ("PCI-Express AER implemetation: AER core and aerdriver")
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@huawei.com>
Signed-off-by: Dongdong Liu <liudongdong3@huawei.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
... and __initconst if applicable.
Based on similar work for an older kernel in the Grsecurity patch.
[JD: fix toshiba-wmi build]
[JD: add htcpen]
[JD: move __initconst where checkscript wants it]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Use a local "struct device *dev" for brevity and consistency in DPC driver.
No functional change intended.
Signed-off-by: Dongdong Liu <liudongdong3@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Add eDPC support. Get and print the RP PIO error information when the
trigger condition is RP PIO error.
For more information on eDPC, please see PCI Express Base Specification
Revision 3.1, section 6.2.10.3, or view the PCI-SIG eDPC ECN here:
https://pcisig.com/sites/default/files/specification_documents/ECN_Enhanced_DPC_2012-11-19_final.pdf
Signed-off-by: Dongdong Liu <liudongdong3@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Move the error handler methods to struct pcie_port_service_driver and avoid
the detour through the mostly unused pci_error_handlers structure.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Commit 76cde7e495 (PCI / PM: Make PCIe PME interrupts wake up from
suspend-to-idle) went too far with preventing pcie_pme_work_fn() from
clearing the root port's PME Status and re-enabling the PME interrupt
which should be done for PMEs to work correctly after system resume.
The failing scenario is as follows:
1. pcie_pme_suspend() finds that the PME IRQ should be designated
for system wakeup, so it calls enable_irq_wake() and then sets
data->suspend_level to PME_SUSPEND_WAKEUP.
2. PME interrupt happens at this point.
3. pcie_pme_irq() runs, disables the PME interrupt and queues up
the execution of pcie_pme_work_fn().
4. pcie_pme_work_fn() runs before pcie_pme_resume() and breaks out
of the loop right away, because data->suspend_level is not
PME_SUSPEND_NONE, and it doesn't re-enable the PME interrupt
for the same reason.
5. pcie_pme_resume() runs and simply calls disable_irq_wake()
without re-enabling the PME interrupt (because data->suspend_level
is not PME_SUSPEND_NONE), so the PME interrupt remains disabled
and the PME Status remains set.
To fix this notice that there is no reason why pcie_pme_work_fn()
should behave in a special way during system resume if the PME
interrupt is not disabled by pcie_pme_suspend() and partially revert
commit 76cde7e495 and restore the previous (and correct) behavior
of pcie_pme_work_fn().
Fixes: 76cde7e495 (PCI / PM: Make PCIe PME interrupts wake up from suspend-to-idle)
Reported-and-tested-by: Naresh Solanki <naresh.solanki@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/portdrv:
PCI/portdrv: Allocate MSI/MSI-X vector for Downstream Port Containment
PCI/portdrv: Support multiple interrupts for MSI as well as MSI-X
The run_wake flag in struct dev_pm_info is used to indicate whether
or not the device is capable of generating remote wakeup signals at
run time (or in the system working state), but the distinction
between runtime remote wakeup and system wakeup signaling has always
been rather artificial. The only practical reason for it to exist
at the core level was that ACPI and PCI treated those two cases
differently, but that's not the case any more after recent changes.
For this reason, get rid of the run_wake flag and, when applicable,
use device_set_wakeup_capable() and device_can_wakeup() instead of
device_set_run_wake() and device_run_wake(), respectively.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
The pme_interrupt flag in struct pci_dev is set when PMEs generated
by the device are going to be signaled via root port PME interrupts.
Ironically enough, that information is only used by the code setting
up device wakeup through ACPI which returns as soon as it sees the
pme_interrupt flag set while setting up "remote runtime wakeup".
That is questionable, however, because in theory there may be PCIe
devices using out-of-band PME signaling under root ports handled
by the native PME code or devices requiring wakeup power setup to be
carried out by AML. For such devices, ACPI wakeup should be invoked
regardless of whether or not native PME signaling is used in general.
For this reason, drop the pme_interrupt flag and rework the code
using it which then allows the ACPI-based device wakeup handling
in PCI to be consolidated to use one code path for both "runtime
remote wakeup" and system wakeup (from sleep states).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Currently pcie_port_enable_irq_vec() only allocates MSI/MSI-X vectors for
PME, hotplug, and AER.
The Downstream Port Containment feature also supports MSI/MSI-X interrupts,
so allocate a vector for it, too.
Signed-off-by: Liudongdong <liudongdong3@huawei.com>
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@huawei.com>
[bhelgaas: changelog, comment]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Root Ports can generate several different interrupts using either MSI or
MSI-X, but we only support that for MSI-X. Ports that support MSI but not
MSI-X are currently limited to sharing a single interrupt.
Rename pcie_port_enable_msix() to pcie_port_enable_irq_vec() and extend it
to support multiple interrupts using either MSI-X (preferred) or MSI.
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@huawei.com>
[bhelgaas: changelog, reword comments, simplify PME/hotplug no-MSI logic]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
This driver was OR'ing desired bits from the existing control setting.
That could create an invalid DPC Trigger Enabled configuration if the
platform previously set this to "ERR_FATAL", 01b. The driver currently
wants to set this to ERR_NONFATAL/ERR_FATAL, 10b, and the logical OR of
this gets 11b, which is reserved. Fix that by masking off the fields it is
setting.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The DPC interupt may be executed on a device that is being removed. Skip
queuing event handling if the status is all 1's, which should be seen only
if the device is not present.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add a new state to pci_dev to be set when it is unexpectedly disconnected.
The PCI driver tear down functions can observe this new device state so
they may skip operations that will fail.
The pciehp and pcie-dpc drivers are aware when the link is down, so these
set the flag when their handlers detect the device is disconnected.
Tested-by: Krishna Dhulipala <krishnad@fb.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Wei Zhang <wzhang@fb.com>
We call pcie_aspm_exit_link_state() when we remove a device. If the device
is the last PCIe function to be removed below a bridge and the bridge has
an ASPM link_state struct, we disable ASPM on the link. Disabling ASPM
requires link->downstream (used in pcie_config_aspm_link()).
We previously set link->downstream in pcie_aspm_cap_init(), but only if the
device was not blacklisted. Removing the blacklisted device caused a NULL
pointer dereference in the pcie_aspm_exit_link_state() ->
pcie_config_aspm_link() path:
# echo 1 > /sys/bus/pci/devices/0000\:0b\:00.0/remove
...
BUG: unable to handle kernel NULL pointer dereference at 0000000000000080
IP: pcie_config_aspm_link+0x5d/0x2b0
Call Trace:
pcie_aspm_exit_link_state+0x75/0x130
pci_stop_bus_device+0xa4/0xb0
pci_stop_and_remove_bus_device_locked+0x1a/0x30
remove_store+0x50/0x70
dev_attr_store+0x18/0x30
sysfs_kf_write+0x44/0x60
kernfs_fop_write+0x10e/0x190
__vfs_write+0x28/0x110
? rcu_read_lock_sched_held+0x5d/0x80
? rcu_sync_lockdep_assert+0x2c/0x60
? __sb_start_write+0x173/0x1a0
? vfs_write+0xb3/0x180
vfs_write+0xc4/0x180
SyS_write+0x49/0xa0
do_syscall_64+0xa6/0x1c0
entry_SYSCALL64_slow_path+0x25/0x25
---[ end trace bd187ee0267df5d9 ]---
To avoid this, set link->downstream in alloc_pcie_link_state(), so every
pcie_link_state structure has a valid link->downstream pointer.
[bhelgaas: changelog]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rajat Jain <rajatja@google.com>
CC: stable@vger.kernel.org
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=4Owc
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.11-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- add ASPM L1 substate support
- enable PCIe Extended Tags when supported
- configure PCIe MPS settings on iProc, Versatile, X-Gene, and Xilinx
- increase VPD access timeout
- add ACS quirks for Intel Union Point, Qualcomm QDF2400 and QDF2432
- use new pci_irq_alloc_vectors() in more drivers
- fix MSI affinity memory leak
- remove unused MSI interfaces and update documentation
- remove unused AER .link_reset() callback
- avoid pci_lock / p->pi_lock deadlock seen with perf
- serialize sysfs enable/disable num_vfs operations
- move DesignWare IP from drivers/pci/host/ to drivers/pci/dwc/ and
refactor so we can support both hosts and endpoints
- add DT ECAM-like support for HiSilicon Hip06/Hip07 controllers
- add Rockchip system power management support
- add Thunder-X cn81xx and cn83xx support
- add Exynos 5440 PCIe PHY support
* tag 'pci-v4.11-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (93 commits)
PCI: dwc: Remove dependency of designware on CONFIG_PCI
PCI: dwc: Add CONFIG_PCIE_DW_HOST to enable PCI dwc host
PCI: dwc: Split pcie-designware.c into host and core files
PCI: dwc: designware: Fix style errors in pcie-designware.c
PCI: dwc: designware: Parse "num-lanes" property in dw_pcie_setup_rc()
PCI: dwc: all: Split struct pcie_port into host-only and core structures
PCI: dwc: designware: Get device pointer at the start of dw_pcie_host_init()
PCI: dwc: all: Rename cfg_read/cfg_write to read/write
PCI: dwc: all: Use platform_set_drvdata() to save private data
PCI: dwc: designware: Move register defines to designware header file
PCI: dwc: Use PTR_ERR_OR_ZERO to simplify code
PCI: dra7xx: Group PHY API invocations
PCI: dra7xx: Enable MSI and legacy interrupts simultaneously
PCI: dra7xx: Add support to force RC to work in GEN1 mode
PCI: dra7xx: Simplify probe code with devm_gpiod_get_optional()
PCI: Move DesignWare IP support to new drivers/pci/dwc/ directory
PCI: exynos: Support the PHY generic framework
Documentation: binding: Modify the exynos5440 PCIe binding
phy: phy-exynos-pcie: Add support for Exynos PCIe PHY
Documentation: samsung-phy: Add exynos-pcie-phy binding
...
* pci/msi:
PCI/MSI: Update MSI/MSI-X bits in PCIEBUS-HOWTO
PCI/MSI: Document pci_alloc_irq_vectors(), deprecate pci_enable_msi()
PCI/MSI: Return -ENOSPC if pci_enable_msi_range() can't get enough vectors
PCI/portdrv: Use pci_irq_alloc_vectors()
PCI/MSI: Check that we have a legacy interrupt line before using it
PCI/MSI: Remove pci_msi_domain_{alloc,free}_irqs()
PCI/MSI: Remove unused pci_msi_create_default_irq_domain()
PCI/MSI: Return failure when msix_setup_entries() fails
PCI/MSI: Remove pci_enable_msi_{exact,range}()
amd-xgbe: Update PCI support to use new IRQ functions
[media] cobalt: use pci_irq_allocate_vectors()
PCI/MSI: Fix msi_capability_init() kernel-doc warnings
Since the exit latencies for L1 substates are not advertised by a device,
it is not clear in spec how to do a L1 substate exit latency check. We
assume that the L1 exit latencies advertised by a device include L1
substate latencies (and hence do not do any check). If that is not true,
we should do some sort of check here.
(I'm not clear about what that check should like currently. I'd be glad to
take up any suggestions).
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Configure the L1 substate settings on the upstream and downstream devices,
while taking care of the rules dictated by the PCIe spec.
[bhelgaas: drop "inline"]
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCIe spec (r3.1, sec 7.33) says the L1 PM Substates Capability may be
implemented only in function 0.
Read the L1 substate capability structures of upstream and downstream
components of the link and set it up in the device structure.
[bhelgaas: add specific spec reference]
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add support for ASPM L1 substates. For details about L1 substates, see the
PCIe r3.1 spec, which includes the ECN below in secs 5.5 and 7.33.
Add macros for the 4 new L1 substates, and add a new ASPM "POWER_SUPERSAVE"
policy that can be used to enable L1 substates on a system if desired. The
new policy is in a sense, a superset of the existing POWERSAVE policy. The
4 policies are now:
DEFAULT: Reads and uses whatever ASPM states BIOS enabled
PERFORMANCE: Everything except L0 disabled.
POWERSAVE: L0s and L1 enabled (but not L1 substates)
POWER_SUPERSAVE: L0s + L1 + L1 substates also enabled
[bhelgaas: add PCIe r3.1 spec reference]
Link: https://pcisig.com/sites/default/files/specification_documents/ECN_L1_PM_Substates_with_CLKREQ_31_May_2013_Rev10a.pdf
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use pci_irq_alloc_vectors() and greatly simplify the code by managing the
vector number for the subservices directly.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Per PCIe r3.1, sec 6.2.10 and sec 7.13.4, on Root Ports that support "RP
Extensions for DPC",
When the DPC Trigger Status bit is Set and the DPC RP Busy bit is Set,
software must leave the Root Port in DPC until the DPC RP Busy bit reads
0b.
Wait up to 1 second for the Root Port to become non-busy.
[bhelgaas: changelog, spec references]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Decode the currently defined extended event reasons rather than just using
the generic "extended" explanation.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
In a struct pcie_link_state, link->root points to the pcie_link_state of
the root of the PCIe hierarchy. For the topmost link, this points to
itself (link->root = link). For others, we copy the pointer from the
parent (link->root = link->parent->root).
Previously we recognized that Root Ports originated PCIe hierarchies, but
we treated PCI/PCI-X to PCIe Bridges as being in the middle of the
hierarchy, and when we tried to copy the pointer from link->parent->root,
there was no parent, and we dereferenced a NULL pointer:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000090
IP: [<ffffffff9e424350>] pcie_aspm_init_link_state+0x170/0x820
Recognize that PCI/PCI-X to PCIe Bridges originate PCIe hierarchies just
like Root Ports do, so link->root for these devices should also point to
itself.
Fixes: 51ebfc92b7 ("PCI: Enumerate switches below PCI-to-PCIe bridges")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=193411
Link: https://bugzilla.opensuse.org/show_bug.cgi?id=1022181
Tested-by: lists@ssl-mail.com
Tested-by: Jayachandran C. <jnair@caviumnetworks.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v4.2+
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ut0k
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.10-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"PCI changes:
- add support for PCI on ARM64 boxes with ACPI. We already had this
for theoretical spec-compliant hardware; now we're adding quirks
for the actual hardware (Cavium, HiSilicon, Qualcomm, X-Gene)
- add runtime PM support for hotplug ports
- enable runtime suspend for Intel UHCI that uses platform-specific
wakeup signaling
- add yet another host bridge registration interface. We hope this is
extensible enough to subsume the others
- expose device revision in sysfs for DRM
- to avoid device conflicts, make sure any VF BAR updates are done
before enabling the VF
- avoid unnecessary link retrains for ASPM
- allow INTx masking on Mellanox devices that support it
- allow access to non-standard VPD for Chelsio devices
- update Broadcom iProc support for PAXB v2, PAXC v2, inbound DMA,
etc
- update Rockchip support for max-link-speed
- add NVIDIA Tegra210 support
- add Layerscape LS1046a support
- update R-Car compatibility strings
- add Qualcomm MSM8996 support
- remove some uninformative bootup messages"
* tag 'pci-v4.10-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (115 commits)
PCI: Enable access to non-standard VPD for Chelsio devices (cxgb3)
PCI: Expand "VPD access disabled" quirk message
PCI: pciehp: Remove loading message
PCI: hotplug: Remove hotplug core message
PCI: Remove service driver load/unload messages
PCI/AER: Log AER IRQ when claiming Root Port
PCI/AER: Log errors with PCI device, not PCIe service device
PCI/AER: Remove unused version macros
PCI/PME: Log PME IRQ when claiming Root Port
PCI/PME: Drop unused support for PMEs from Root Complex Event Collectors
PCI: Move config space size macros to pci_regs.h
x86/platform/intel-mid: Constify mid_pci_platform_pm
PCI/ASPM: Don't retrain link if ASPM not possible
PCI: iproc: Skip check for legacy IRQ on PAXC buses
PCI: pciehp: Leave power indicator on when enabling already-enabled slot
PCI: pciehp: Prioritize data-link event over presence detect
PCI: rcar: Add gen3 fallback compatibility string for pcie-rcar
PCI: rcar: Use gen2 fallback compatibility last
PCI: rcar-gen2: Use gen2 fallback compatibility last
PCI: rockchip: Move the deassert of pm/aclk/pclk after phy_init()
..
* pci/pm:
x86/platform/intel-mid: Constify mid_pci_platform_pm
PCI: pciehp: Add runtime PM support for PCIe hotplug ports
ACPI / hotplug / PCI: Make device_is_managed_by_native_pciehp() public
ACPI / hotplug / PCI: Use cached copy of PCI_EXP_SLTCAP_HPC bit
PCI: Unfold conditions to block runtime PM on PCIe ports
PCI: Consolidate conditions to allow runtime PM on PCIe ports
PCI: Activate runtime PM on a PCIe port only if it can suspend
PCI: Speed up algorithm in pci_bridge_d3_update()
PCI: Autosense device removal in pci_bridge_d3_update()
PCI: Don't acquire ref on parent in pci_bridge_d3_update()
USB: UHCI: report non-PME wakeup signalling for Intel hardware
PCI: Check for PME in targeted sleep state
Remove the "service driver %s loaded" and unloaded messages. All service
drivers already log something in their probe functions, where they can log
more useful details.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
All other AER-related log messages use the PCI device, e.g.,
"pci 0000:00:1c.0", not the PCIe service device, e.g.,
"aer 0000:00:1c.0:pcie02".
Change the probe error messages to match the rest and include a little
context.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Remove the unused DRIVER_VERSION, DRIVER_AUTHOR, and DRIVER_DESC macros.
The author information is already included in a comment above.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We already log a "Signaling PME" whenever the PME service driver claims a
Root Port. In fact, we also log the same message for every device in the
hierarchy below the Root Port.
Log the "Signaling PME" once (only for the Root Port, since we can
trivially find out which devices are below the Root Port), and include the
IRQ number in the message to help connect the dots with /proc/interrupts.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since we register pcie_pme_driver only for PCI_EXP_TYPE_ROOT_PORT, the PME
driver never claims Root Complex Event Collectors.
Remove unused code related to Root Complex Event Collectors.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some (defective) PCIe devices are not able to reliably do link retraining.
Check to see if ASPM is possible between link partners before configuring
common clocking, and doing the resulting link retraining. If ASPM is not
possible, there is no reason to risk losing access to a device due to an
unnecessary link retraining.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Export pcie_find_root_port() so we can use it outside of PCIe-AER error
injection.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The conditions to allow runtime PM on PCIe ports are currently spread
across two different files: The condition relating to hotplug ports is
located in portdrv_pci.c whereas all other conditions are located in pci.c.
Consolidate all conditions in a single place in pci.c, thus making it
easier to follow the logic and amend conditions down the road.
Note that the condition relating to hotplug ports is inserted *before* the
condition relating to the "pcie_port_pm=force" command line option, so
runtime PM is not afforded to hotplug ports even if this option is given.
That's exactly how the code behaved up until now. If this is not desired,
the ordering of the conditions can simply be reversed.
No functional change intended.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently pcie_portdrv_probe() activates runtime PM on a PCIe port even
if it will never actually suspend because the BIOS is too old or the
"pcie_port_pm=off" option was specified on the kernel command line.
A few CPU cycles can be saved by not activating runtime PM at all in these
cases, because rpm_idle() and rpm_suspend() will bail out right at the
beginning when calling rpm_check_suspend_allowed(), instead of carrying out
various locking and assignments, invoking rpm_callback(), getting back
-EBUSY and rolling everything back.
The conditions checked in pci_bridge_d3_possible() are all static, they
never change during uptime of the system, hence it's safe to call this to
determine if runtime PM should be activated.
No functional change intended.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use DEVICE_ATTR_RW for read-write attributes. This simplifies the source
code, improves readability, and reduces the chance of inconsistencies.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@rw@
declarer name DEVICE_ATTR;
identifier x,x_show,x_store;
@@
DEVICE_ATTR(x, \(0644\|S_IRUGO|S_IWUSR\), x_show, x_store);
@script:ocaml@
x << rw.x;
x_show << rw.x_show;
x_store << rw.x_store;
@@
if not (x^"_show" = x_show && x^"_store" = x_store)
then Coccilib.include_match false
@@
declarer name DEVICE_ATTR_RW;
identifier rw.x,rw.x_show,rw.x_store;
@@
- DEVICE_ATTR(x, \(0644\|S_IRUGO|S_IWUSR\), x_show, x_store);
+ DEVICE_ATTR_RW(x);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
0516c8bcd2 ("PCI: PCIe portdrv: Simplily probe callback of service
drivers") removed the "id" argument of aer_probe() but neglected to remove
the kernel-doc comment. Update the comment.
[bhelgaas: changelog]
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Save the position of the error reporting capability so it doesn't need to
be rediscovered during error handling.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Lukas Wunner <lukas@wunner.de>
When handling AER events, we previously allocated a struct aer_err_info,
processed the error, and freed the struct. But aer_isr_one_error() is
serialized by rpc_mutex, so we never need more than one copy of the struct,
and the struct is only about 70 bytes, so we're not saving much by
allocating it dynamically.
Embed a struct aer_err_info directly in struct aer_rpc, which is allocated
at probe-time by aer_probe().
[bhelgaas: changelog]
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Currently the AER severity is being translated twice in the code flow for
PCIe errors. It is first translated in ghes_do_proc() before calling into
the AER driver. Then it is translated again when the AER driver calls
cper_print_aer(). This causes the severity that is used in
cper_print_aer() to be incorrect.
Remove the second translation that is in cper_print_aer() since this
function is already receiving the correct AER severity.
Signed-off-by: Tyler Baicar <tbaicar@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Borislav Petkov <bp@suse.de>
Per the PCI Firmware spec, r3.0, sec 4.5.1, on ACPI systems, the OS must
not use AER unless _OSC is present and _OSC grants AER control to the OS.
The aerdriver.forceload kernel parameter was a way to enable Linux AER
support on ACPI systems that lack _OSC or fail to grant control the the OS.
Enabling Linux AER support when the firmware doesn't want us to is a recipe
for problems, e.g., the firmware might be handling AER itself.
Remove the aerdriver.forceload kernel parameter and related supporting
code.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The aerdriver.nosourceid kernel parameter was intended for working around
broken chipsets don't supply the source ID for AER events. We recently
added PCI_BUS_FLAGS_NO_AERSID, which can be set by quirks for the same
purpose.
Remove the aerdriver.nosourceid kernel parameter. For anything other than
debugging, asking users to find and use kernel parameters is a poor user
experience. Instead, we should add PCI_BUS_FLAGS_NO_AERSID quirks for any
hardware that needs it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Allow root port buses to choose to skip source id matching when finding the
faulting device. Certain root port devices may return an incorrect source
ID and recommend to scan child device registers for AER notifications.
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/ptm:
PCI: Add PTM clock granularity information
PCI: Add pci_enable_ptm() for drivers to enable PTM on endpoints
PCI: Add Precision Time Measurement (PTM) support
The PTM Control register (PCIe r3.1, sec 7.32.3) contains an Effective
Granularity field:
This provides information relating to the expected accuracy of the PTM
clock, but does not otherwise affect the PTM mechanism.
Set the Effective Granularity based on the PTM Root and any intervening PTM
Time Sources.
This does not set Effective Granularity for Root Complex Integrated
Endpoints because I don't know how to figure out clock granularity for
them. The spec says:
... system software must set [Effective Granularity] to the value
reported in the Local Clock Granularity field by the associated PTM
Time Source.
but I don't know how to identify the associated PTM Time Source. Normally
it's the upstream bridge, but an integrated endpoint has no upstream
bridge.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This code is not being built as a module by anyone:
obj-$(CONFIG_PCIEAER) += aerdriver.o
aerdriver-objs := aerdrv_errprint.o aerdrv_core.o aerdrv.o
drivers/pci/pcie/aer/Kconfig:config PCIEAER
drivers/pci/pcie/aer/Kconfig: bool "Root Port Advanced Error Reporting support"
Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.
Note that for non-modular code, module_init() translates to
device_initcall().
[bhelgaas: changelog]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Tom Long Nguyen <tom.l.nguyen@intel.com>
This code is not being built as a module by anyone:
config PCIE_PME
def_bool y
depends on PCIEPORTBUS && PM
Remove traces of modularity so that when reading the driver there is no
doubt it is builtin-only.
Also delete the .remove function, since that doesn't seem to have a
sensible use case. With "normal" endpoint drivers, we have in the past set
the suppress_bind_attrs bit to make it clear that the use of ".remove" in a
builtin driver was deleted, but here for PCI, it seems overkill to jump
through the pcie_port_service_driver and into the struct device_driver in
order to finally try and do something similar with the bind setting.
Note that for non-modular code, module_init() translates to
device_initcall().
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This code is not being built as a module by anyone:
drivers/pci/pcie/Kconfig:config PCIE_DPC
drivers/pci/pcie/Kconfig: bool "PCIe Downstream Port Containment support"
Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.
Note that for non-modular code, module_init() translates to
device_initcall().
[bhelgaas: changelog]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Keith Busch <keith.busch@intel.com>
CC: Mika Westerberg <mika.westerberg@linux.intel.com>
This code is not being built as a module by anyone:
pcieportdrv-y := portdrv_core.o portdrv_pci.o portdrv_bus.o
obj-$(CONFIG_PCIEPORTBUS) += pcieportdrv.o
drivers/pci/pcie/Kconfig:config PCIEPORTBUS
drivers/pci/pcie/Kconfig: bool "PCI Express Port Bus support"
Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.
Note that for non-modular code, MODULE_DEVICE_TABLE is a no-op and
module_init() translates to device_initcall().
[bhelgaas: changelog, remove unused DRIVER_* macros]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Tom Long Nguyen <tom.l.nguyen@intel.com>
Add an pci_enable_ptm() interface so drivers can enable PTM.
The PCI core enables PTM on PTM Roots and switches automatically, but we
don't enable PTM on endpoints unless a driver requests it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add Precision Time Measurement (PTM) support (see PCIe r3.1, sec 6.22).
Enable PTM on PTM Root devices and switch ports. This does not enable PTM
on endpoints.
There currently are no PTM-capable devices on the market, but it is
expected to be supported by the Intel Apollo Lake platform.
[bhelgaas: complete rework]
Signed-off-by: Jonathan Yong <jonathan.yong@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/aspm:
PCI/ASPM: Remove redundant check of pcie_set_clkpm
* pci/dpc:
PCI: Remove DPC tristate module option
PCI: Bind DPC to Root Ports as well as Downstream Ports
PCI: Fix whitespace in struct dpc_dev
PCI: Convert Downstream Port Containment driver to use devm_* functions
* pci/hotplug:
PCI: Allow additional bus numbers for hotplug bridges
* pci/misc:
PCI: Include <asm/dma.h> for isa_dma_bridge_buggy
PCI: Make bus_attr_resource_alignment static
MAINTAINERS: Add file patterns for PCI device tree bindings
PCI: Fix comment typo
* pci/msi:
PCI/MSI: irqchip: Fix PCI_MSI dependencies
* pci/pm:
PCI: pciehp: Ignore interrupts during D3cold
PCI: Document connection between pci_power_t and hardware PM capability
PCI: Add runtime PM support for PCIe ports
ACPI / hotplug / PCI: Runtime resume bridge before rescan
PCI: Power on bridges before scanning new devices
PCI: Put PCIe ports into D3 during suspend
PCI: Don't clear d3cold_allowed for PCIe ports
PCI / PM: Enforce type casting for pci_power_t
* pci/virtualization:
PCI: Add ACS quirk for Solarflare SFC9220
PCI: Add DMA alias quirk for Adaptec 3805
PCI: Mark Atheros AR9485 and QCA9882 to avoid bus reset
PCI: Add function 1 DMA alias quirk for Marvell 88SE9182
Change the Downstream Port Containment config type from tristate to bool.
The driver doesn't automatically load based on any rules, so it needs to be
built-in in order to bind to devices it needs to drive.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
PCIe port type values are not flags, so OR'ing them is not correct.
Previously the result was equivalent to PCIe Downstream Ports, so we were
missing binding to DPC-capable Root Ports.
Change the type to 'any' so we can bind to both port types. While this
will cause the code to check Upstream Ports, the driver won't claim them
since they are not DPC-capable.
Reported-by: Alexander Antonov <alexanderx.v.antonov@intel.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Mika Westerberg <mika.westerberg@linux.intel.com>
Use the device resource management (devm) interfaces so we don't need to
explicitly release resources on failure paths or when the driver is
removed.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Keith Busch <keith.busch@intel.com>
Add back runtime PM support for PCIe ports that was removed by
fe9a743a26 ("PCI/PM: Drop unused runtime PM support code for PCIe
ports").
We cannot enable it automatically for all ports since there have been
problems previously [1]. In summary suspended PCIe ports were not able
to deal with ACPI-based hotplug reliably. One reason why this might happen
is the fact that when a PCIe port is powered down, config space access to
the devices behind the port is not possible. If the BIOS hotplug SMI
handler assumes the port is always in D0 it will not be able to find the
hotplugged devices. To be on the safe side only enable runtime PM if the
port does not claim to support hotplug.
For PCIe ports not using hotplug, we enable and allow runtime PM
automatically. Since 'bridge_d3' can be changed any time we check this in
driver ->runtime_idle() and ->runtime_suspend() and only allow runtime
suspend if the flag is still set. Use autosuspend with default of 100ms
idle time to prevent the port from repeatedly suspending and resuming on
continuous configuration space access of devices behind the port.
The actual power transition to D3 and back is handled in the PCI core.
Idea to automatically unblock (allow) runtime PM for PCIe ports came from
Dave Airlie.
[1] https://bugzilla.kernel.org/show_bug.cgi?id=53811
This includes a fix for lockdep issue reported by Valdis Kletnieks.
Tested-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The PCI core skips bridges and ports when the system is suspended. The PCI
core checks return value of pci_has_subordinate() in pci_pm_suspend_noirq()
to skip all devices where it is non-zero (which means PCI bridges and PCIe
ports).
Since PCIe ports are never suspended in the first place, there is no need
to set d3cold_allowed for them.
Tested-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Without supporting clock PM capable, if we want to disable clkpm, we don't
need this extra check as it must already be zero for the enable argument.
And it's the same for enabling clkpm here. So let's remove this check.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/hotplug:
PCI: Use cached copy of PCI_EXP_SLTCAP_HPC bit
* pci/resource:
PCI: Disable all BAR sizing for devices with non-compliant BARs
x86/PCI: Mark Broadwell-EP Home Agent 1 as having non-compliant BARs
PCI: Identify Enhanced Allocation (EA) BAR Equivalent resources in sysfs
We cache the PCI_EXP_SLTCAP_HPC bit in pci_dev->is_hotplug_bridge on device
probe, so there's no need to read it again on allocation of port service
devices.
No functional change intended.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/dpc:
PCI: Add Downstream Port Containment driver
PCI: Add Downstream Port Containment portdrv service type
PCI: Widen portdrv service type from 4 bits to 8 bits
* pci/resource:
alpha/PCI: Call iomem_is_exclusive() for IORESOURCE_MEM, but not IORESOURCE_IO
PCI: Supply CPU physical address (not bus address) to iomem_is_exclusive()
* pci/thunderbolt:
thunderbolt: Fix double free of drom buffer
Add driver for the PCI Express Downstream Port Containment extended
capability. DPC is an optional capability to contain uncorrectable errors
below a port.
For more information on DPC, please see PCI Express Base Specification
Revision 4, section 7.31, or view the PCI-SIG DPC ECN here:
https://pcisig.com/sites/default/files/specification_documents/ECN_DPC_2012-02-09_finalized.pdf
When a DPC event is triggered, the hardware disables downstream links, so
the DPC driver schedules removal for all devices below this port. This may
happen concurrently with a PCIe hotplug driver if enabled. When all
downstream devices are removed and the link state transitions to disabled,
the DPC driver clears the DPC status and interrupt bits so the link may
retrain for a newly connected device.
[bhelgaas: clear (not set) DPC_CTL bits on remove, whitespace cleanup]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lukas Wunner <lukas@wunner.de>
Add the Downstream Port Containment (PCIE_PORT_SERVICE_DPC) portdrv service
type, available if the device has the DPC extended capability.
[bhelgaas: split to separate patch, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The names of port service devices previously used one nibble to encode the
port type and another nibble to encode the service type. We're about to
add a fifth service type, so change device names to use one *byte* to
encode the service type.
For example, a hotplug port service on a downstream bridge was previously
called "pcie24" and is now called "pcie204". The "2" encodes the device
type (PCI_EXP_TYPE_DOWNSTREAM - 4), and the "4" (now "04") encodes the
service (PCIE_PORT_SERVICE_HP).
Based on Lukas Wunner's patch:
b688d6e487
[bhelgaas: split to separate patch, expand changelog]
Based-on-patch-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Now that pcie_port_acpi_setup() always returns 0, make it and its callers
void functions and stop checking the return values.
[bhelgaas: changelog]
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Host bridges we discover via ACPI, i.e., PNP0A03 and PNP0A08 devices, may
have an _OSC method by which the OS can ask the platform for control of
PCIe features like native hotplug, power management events, AER, etc.
Previously, if we found a bridge without an ACPI device, we assumed we did
not have permission to use any of these PCIe features. That seems
unreasonably restrictive.
If we find no ACPI device, assume we can take control of all PCIe features.
The Intel Volume Management Device (VMD) is one such bridge with no ACPI
device. Prior to this change, users had to boot with "pcie_ports=native"
to get hotplug and other services to work below the VMD Root Port.
[bhelgaas: changelog]
Suggested-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/aer:
PCI/AER: Log aer_inject error injections
PCI/AER: Log actual error causes in aer_inject
PCI/AER: Use dev_warn() in aer_inject
PCI/AER: Fix aer_inject error codes
* pci/enumeration:
PCI: Fix broken URL for Dell biosdevname
* pci/kconfig:
PCI: Cleanup pci/pcie/Kconfig whitespace
PCI: Include pci/hotplug Kconfig directly from pci/Kconfig
PCI: Include pci/pcie/Kconfig directly from pci/Kconfig
* pci/misc:
PCI: Add PCI_CLASS_SERIAL_USB_DEVICE definition
PCI: Add QEMU top-level IDs for (sub)vendor & device
unicore32: Remove unused HAVE_ARCH_PCI_SET_DMA_MASK definition
PCI: Consolidate PCI DMA constants and interfaces in linux/pci-dma-compat.h
PCI: Move pci_dma_* helpers to common code
frv/PCI: Remove stray pci_{alloc,free}_consistent() declaration
* pci/virtualization:
PCI: Wait for up to 1000ms after FLR reset
PCI: Support SR-IOV on any function type
* pci/vpd:
PCI: Prevent VPD access for buggy devices
PCI: Sleep rather than busy-wait for VPD access completion
PCI: Fold struct pci_vpd_pci22 into struct pci_vpd
PCI: Rename VPD symbols to remove unnecessary "pci22"
PCI: Remove struct pci_vpd_ops.release function pointer
PCI: Move pci_vpd_release() from header file to pci/access.c
PCI: Move pci_read_vpd() and pci_write_vpd() close to other VPD code
PCI: Determine actual VPD size on first access
PCI: Use bitfield instead of bool for struct pci_vpd_pci22.busy
PCI: Allow access to VPD attributes with size 0
PCI: Update VPD definitions
Clean up style issues in drivers/pci/pcie/Kconfig, in particular all
indentation is now done using tabs, not spaces, and the definition of
PCIEASPM_DEBUG is now separated from the definition of PCIEASPM with a
newline.
Signed-off-by: Andreas Ziegler <andreas.ziegler@fau.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Log successful error injections so that injected errors can be
differentiated from real errors.
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Borislav Petkov <bp@suse.de>
The aer_inject driver is very quiet. In most cases, it merely returns an
error code to user-space, leaving the user with little clue about the
actual reason for the failure.
So, log error messages for 4 of the most frequent causes of failure:
* Can't find the root port of the specified device.
* Device doesn't support AER.
* Root port doesn't support AER.
* AER device not found.
This gives the user a chance to understand why aer-inject failed.
Based on a preliminary patch by Thomas Renninger.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Borislav Petkov <bp@suse.de>
CC: Thomas Renninger <trenn@suse.de>
dev_warn() is better than printk(LOG_WARNING...) as it records which device
the message relates to. Also add a prefix "aer_inject:" to help
differentiate real errors from injected errors.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Borislav Petkov <bp@suse.de>
EPERM means "Operation not permitted", which doesn't reflect the lack of
support for AER. EPROTONOSUPPORT (Protocol not supported) is a better
choice of error code if the device or its root port lack support for AER.
Likewise, EINVAL means "Invalid argument", which is not suitable for cases
where the AER error device is missing or unusable. ENODEV and
EPROTONOSUPPORT, respectively, fit better.
Suggested-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Borislav Petkov <bp@suse.de>
CC: Prarit Bhargava <prarit@redhat.com>
* pci/aer:
PCI/AER: Use list_first_entry_or_null() to simplify code
PCI/AER: Restore pci_ops pointer while calling original pci_ops
PCI/AER: Rename pci_ops_aer to aer_inj_pci_ops
* pci/misc:
PCI: Remove includes of asm/pci-bridge.h
PCI: Remove empty asm-generic/pci-bridge.h
ARM64: PCI: Remove generated include of asm-generic/pci-bridge.h
PCI: Remove includes of empty asm-generic/pci-bridge.h
PCI: Move pci_set_flags() from asm-generic/pci-bridge.h to linux/pci.h
PCI/PME: Restructure pcie_pme_suspend() to prevent compiler warning
PCI/PME: Remove redundant port lookup
PCI: Check device_attach() return value always
* pci/virtualization:
PCI: Add ACS quirk for all Cavium devices
Previously we had this:
if (wakeup)
ret = enable_irq_wake(...);
if (!wakeup || ret)
...
"ret" is only evaluated when "wakeup" is true, and it is always initialized
in that case, but gcc isn't smart enough to figure that out and warns:
drivers/pci/pcie/pme.c:414:14: warning: 'ret' may be used uninitialized in this function [-Wmaybe-uninitialized]
Restructure the code slightly to make it easier for gcc (and maybe for
humans as well).
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com
We've already looked up srv->port a few lines earlier, and there's no need
to do it again. Remove the redundant lookup.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com
Bjorn Helgaas