PCIe native PME detection mechanism is based on interrupts generated
by root ports or event collectors every time a PCIe device sends a
PME message upstream.
Once a PME message has been sent by an endpoint device and received
by its root port (or event collector in the case of root complex
integrated endpoints), the Requester ID from the message header is
registered in the root port's Root Status register. At the same
time, the PME Status bit of the Root Status register is set to
indicate that there's a PME to handle. If PCIe PME interrupt is
enabled for the root port, it generates an interrupt once the PME
Status has been set. After receiving the interrupt, the kernel can
identify the PCIe device that generated the PME using the Requester
ID from the root port's Root Status register. [For details, see PCI
Express Base Specification, Rev. 2.0.]
Implement a driver for the PCIe PME root port service working in
accordance with the above description.
Based on a patch from Shaohua Li <shaohua.li@intel.com>.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The aer_inject module hangs in aer_inject() when checking the device's
error masks. The hang is due to a recursive use of the aer_inject lock.
The aer_inject() routine grabs the lock while processing the error and then
calls pci_read_config_dword to read the masks. The pci_read_config_dword
routine is earlier overridden by pci_read_aer, which among other things,
grabs the aer_inject lock.
Fixed by moving the pci_read_config_dword calls to read the masks to before
the lock is taken.
Acked-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The Correcteable/Uncorrectable Error Mask Registers are used by PCIe AER
driver which will controls the reporting of individual errors to PCIe RC
via PCIe error messages.
If hardware masks special error reporting to RC, the aer_inject driver
should not inject aer error.
Acked-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Youquan, Song <youquan.song@intel.com>
Acked-by: Ying, Huang <ying.huang@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Changing occurrences of variants of PCI-X and PCIe to the PCI-SIG
terms listed in the "Trademark and Logo Usage Guidelines".
http://www.pcisig.com/developers/procedures/logos/Trademark_and_Logo_Usage_Guidelines_updated_112206.pdf
Patch is limited to drivers/pci/ and changes concern non-comment parts or
anything that might be visible to the user.
Signed-off-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This problem happened when removing PCIe root port using PCI logical
hotplug operation.
The immediate cause of this problem is that the pointer to invalid
data structure is passed to pcie_update_aspm_capable() by
pcie_aspm_exit_link_state(). When pcie_aspm_exit_link_state() received
a pointer to root port link, it unconfigures the root port link and
frees its data structure at first. At this point, there are not links
to configure under the root port and the data structure for root port
link is already freed. So pcie_aspm_exit_link_state() must not call
pcie_update_aspm_capable() and pcie_config_aspm_path().
This patch fixes the problem by changing pcie_aspm_exit_link_state()
not to call pcie_update_aspm_capable() and pcie_config_aspm_path() if
the specified link is root port link.
------------[ cut here ]------------
kernel BUG at drivers/pci/pcie/aspm.c:606!
invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC
last sysfs file: /sys/devices/pci0000:40/0000:40:13.0/remove
CPU 1
Modules linked in: shpchp
Pid: 9345, comm: sysfsd Not tainted 2.6.32-rc5 #98 ProLiant DL785 G6
RIP: 0010:[<ffffffff811df69b>] [<ffffffff811df69b>] pcie_update_aspm_capable+0x15/0xbe
RSP: 0018:ffff88082a2f5ca0 EFLAGS: 00010202
RAX: 0000000000000e77 RBX: ffff88182cc3e000 RCX: ffff88082a33d006
RDX: 0000000000000001 RSI: ffffffff811dff4a RDI: ffff88182cc3e000
RBP: ffff88082a2f5cc0 R08: ffff88182cc3e000 R09: 0000000000000000
R10: ffff88182fc00180 R11: ffff88182fc00198 R12: ffff88182cc3e000
R13: 0000000000000000 R14: ffff88182cc3e000 R15: ffff88082a2f5e20
FS: 00007f259a64b6f0(0000) GS:ffff880864600000(0000) knlGS:0000000000000000
CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: 00007feb53f73da0 CR3: 000000102cc94000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process sysfsd (pid: 9345, threadinfo ffff88082a2f4000, task ffff88082a33cf00)
Stack:
ffff88182cc3e000 ffff88182cc3e000 0000000000000000 ffff88082a33cf00
<0> ffff88082a2f5cf0 ffffffff811dff52 ffff88082a2f5cf0 ffff88082c525168
<0> ffff88402c9fd2f8 ffff88402c9fd2f8 ffff88082a2f5d20 ffffffff811d7db2
Call Trace:
[<ffffffff811dff52>] pcie_aspm_exit_link_state+0xf5/0x11e
[<ffffffff811d7db2>] pci_stop_bus_device+0x76/0x7e
[<ffffffff811d7d67>] pci_stop_bus_device+0x2b/0x7e
[<ffffffff811d7e4f>] pci_remove_bus_device+0x15/0xb9
[<ffffffff811dcb8c>] remove_callback+0x29/0x3a
[<ffffffff81135aeb>] sysfs_schedule_callback_work+0x15/0x6d
[<ffffffff81072790>] worker_thread+0x19d/0x298
[<ffffffff8107273b>] ? worker_thread+0x148/0x298
[<ffffffff81135ad6>] ? sysfs_schedule_callback_work+0x0/0x6d
[<ffffffff810765c0>] ? autoremove_wake_function+0x0/0x38
[<ffffffff810725f3>] ? worker_thread+0x0/0x298
[<ffffffff8107629e>] kthread+0x7d/0x85
[<ffffffff8102eafa>] child_rip+0xa/0x20
[<ffffffff8102e4bc>] ? restore_args+0x0/0x30
[<ffffffff81076221>] ? kthread+0x0/0x85
[<ffffffff8102eaf0>] ? child_rip+0x0/0x20
Code: 89 e5 8a 50 48 31 c0 c0 ea 03 83 e2 07 e8 b2 de fe ff c9 48 98 c3 55 48 89 e5 41 56 49 89 fe 41 55 41 54 53 48 83 7f 10 00 74 04 <0f> 0b eb fe 48 8b 05 da 7d 63 00 4c 8d 60 e8 4c 89 e1 eb 24 4c
RIP [<ffffffff811df69b>] pcie_update_aspm_capable+0x15/0xbe
RSP <ffff88082a2f5ca0>
---[ end trace 6ae0f65bdeab8555 ]---
Reported-by: Alex Chiang <achiang@hp.com>
Tested-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The pci_cleanup_aer_correct_error_status() function has been
#if 0'd out since 2.6.25. Time to remove the dead code.
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The current implementation of pci_cleanup_aer_uncorrect_error_status
only clears either fatal or non-fatal error status bits depending
on the state of the I/O channel. This implementation will then often
leave some bits set after PCI error recovery completes. The uncleared bit
settings will then be falsely reported the next time an AER interrupt is
generated for that hierarchy. An easy way to illustrate this issue is to
use the aer-inject module to simultaneously inject both an uncorrectable
non-fatal and uncorrectable fatal error. One of the errors will not be
cleared.
This patch resolves this issue by unconditionally clearing all bits in
the AER uncorrectable status register. All settings and corrective action
strategies are saved and determined before
pci_cleanup_aer_uncorrect_error_status is called, so this change should not
affect errory handling functionality.
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Remove 'port_type' field in struct pcie_port_data(), because we can
get port type information from struct pci_dev. With this change, this
patch also does followings:
- Remove struct pcie_port_data because it no longer has any field.
- Remove portdrv private definitions about port type (PCIE_RC_PORT,
PCIE_SW_UPSTREAM_PORT and PCIE_SW_DOWNSTREAM_PORT), and use generic
definitions instead.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Add missing service irqs cleanup in the error code path of
pcie_port_device_register().
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Call pci_enable_device() before initializing service irqs, because
legacy interrupt is initialized in pci_enable_device() on some
architectures.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch cleans up the service irqs initialization as follows:
- Remove 'irq_mode' field in pcie_port_data and related definitions,
which is not needed because we can get the same information from
'is_msix', 'is_msi' and 'pin' fields in struct pci_dev.
- Change the name of 'vectors' argument of assign_interrupt_mode() to
'irqs' because it holds irq numbers actually. People might confuse
it with CPU vector or MSI/MSI-X vector.
- Change function name assign_interrupt_mode() to init_service_irqs()
becasuse we no longer have 'irq_mode' data structure, and new name
is more straightforward (IMO).
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
No reason to check PME capability outside get_port_device_capability().
Do it in get_port_device_capability().
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
PCIe port type is already stored in 'pcie_type' field of struct
pci_dev. So we don't need to get it from pci configuration space.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
In the current port bus driver implementation, pcie_device allocation,
initialization and registration are done in separated functions. Doing
those in one function make the code simple and easier to read.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We don't need pcie_port_device_probe() because we can get pci
device/port type using pci_is_pcie() and 'pcie_type' fields in struct
pci_dev. Remove pcie_port_device_probe().
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Changes for PCIe AER driver to use pci_is_pcie() instead of checking
pci_dev->is_pcie.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Change for PCIe ASPM driver to use pci_is_pcie() instead of checking
pci_dev->is_pcie.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use pci_pcie_cap() instead of pci_find_capability() to get PCIe capability
offset in PCIe ASPM driver. This avoids unnecessary search in PCI
configuration space.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use pci_pcie_cap() instead of pci_find_capability() to get PCIe capability
offset in PCI Express Port Bus driver. This avoids unnecessary serarch
in PCI configuration space.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use pcie_cap() instead of pci_find_capability() to get PCIe capability
offset in PCIe AER driver. This avoids unnecessary search in PCI
configuration space.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Replaced some error return values in aer_inject. Use -ENODEV when we
can't find a device and -ENOTTY when the device does not support PCIe AER.
Acked-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Add support for PCI domains (segments) to aer_inject.
Acked-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Feedback from Hidetoshi Seto and Kenji Kaneshige incorporated. This
correctly handles PCI-X bridges, PCIe root ports and endpoints, and
prints debug messages when invalid/reserved types are found in the
HEST. PCI devices not in domain/segment 0 are not represented in
HEST, thus will be ignored.
Today, the PCIe Advanced Error Reporting (AER) driver attaches itself
to every PCIe root port for which BIOS reports it should, via ACPI
_OSC.
However, _OSC alone is insufficient for newer BIOSes. Part of ACPI
4.0 is the new APEI (ACPI Platform Error Interfaces) which is a way
for OS and BIOS to handshake over which errors for which components
each will handle. One table in ACPI 4.0 is the Hardware Error Source
Table (HEST), where BIOS can define that errors for certain PCIe
devices (or all devices), should be handled by BIOS ("Firmware First
mode"), rather than be handled by the OS.
Dell PowerEdge 11G server BIOS defines Firmware First mode in HEST, so
that it may manage such errors, log them to the System Event Log, and
possibly take other actions. The aer driver should honor this, and
not attach itself to devices noted as such.
Furthermore, Kenji Kaneshige reminded us to disallow changing the AER
registers when respecting Firmware First mode. Platform firmware is
expected to manage these, and if changes to them are allowed, it could
break that firmware's behavior.
The HEST parsing code may be replaced in the future by a more
feature-rich implementation. This patch provides the minimum needed
to prevent breakage until that implementation is available.
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Reviewed-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: Prevent AER driver from being loaded on non-root port PCIE devices
PCI: get larger bridge ranges when space is available
PCI: pci.c: fix kernel-doc notation
PCI quirk: TI XIO200a erroneously reports support for fast b2b transfers
PCI PM: Read device power state from register after updating it
PCI: remove pci_assign_resource_fixed()
PCI: PCIe portdrv: remove "-driver" from driver name
After m68k's task_thread_info() doesn't refer to current,
it's possible to remove sched.h from interrupt.h and not break m68k!
Many thanks to Heiko Carstens for allowing this.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
A bug was seen on boards using a PLX 8518 switch device which advertises
AER on each of it's transparent bridges. The AER driver was loaded for
each bridge and this driver tried to access the AER source ID register
whenever an interrupt occured on the shared PCI INTX lines. The source
ID register does not exist on non root port PCIE device's which
advertise AER and trying to access this register causes a unsupported
request error on the bridge. Thus, when the next interrupt occurs,
another error is found and the non existent source ID register is
accessed again, and so it goes on.
The result is a spammed dmesg with unsupported request PCI express
errors on the bridge device that the AER driver is loaded against.
Reported-by: Malcolm Crossley <malcolm.crossley2@gefanuc.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Tested-by: Malcolm Crossley <malcolm.crossley2@gefanuc.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
No need to include "-driver" in the driver name.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
CC: Tom Long Nguyen <tom.l.nguyen@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
When booting with pci=nomsi aer causes lost interrupts and
lockdep inversions.
So check if MSIs are not disabled before initializing the aer
driver.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The definition of the ASPM support field in the Link Capabilities
Register had been changed by the "ASPM optionality ECN" as follows:
<Before>
00b Reserved
01b L0s Supported
10b Reserved
11b L0s and L1 Supported
<After>
00b No ASPM Support
01b L0s Supported
10b L1 Supported
11b L0s and L1 Supported
Current linux ASPM driver doesn't enable ASPM if the support field is
00b or 10b. So there is no impact about 00b. But current linux ASPM
driver doesn't enable L1 if the support field is 10b. With this patch,
10b (L1 support) is handled properly.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
After commit c82f63e411
(PCI: check saved state before restore) pcie_portdrv_slot_reset()
may not work correctly if dev->error_state is equal to
pci_channel_io_frozen, because dev->state_saved need not be set at
that time. Fix this issue by setting dev->state_saved before
pci_restore_state() is called in pcie_portdrv_slot_reset().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
There is a very old quirk for the intel E7502 E7320 and E7525 memory
controller hubs that disables usage of msi interrupts on pcie hotplug
bridges of those devices, and disables changing the affinity of irqs.
Today all we have to do to disable msi on a specific device is to set
dev->no_msi, which is much more straightforward than the previous
logic.
The re-running of this fixup after pci hotplug happens below these
devices is totally bogus. All of the state we change is pure software
state and we don't change the hardware at all. Which means hotplug on
the lower devices doesn't have a chance to change this state. So we
can safely remove the special case from the pciehp driver and the pcie
portdriver.
I suspect the special case was someone's expermental debug code that
slipped in. Certainly it isn't mentioned in commit
6fb8880a61510295aece04a542767161f624dffe aka BKrev:
41966101LJ_ogfOU0m2aE6teZfQnuQ where the code first appears.
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Multiple bits might be set in the Uncorrectable Error Status
register. But aer_print_error_source() only report a error of
the lowest bit set in the error status register.
So print strings for all bits unmasked and set.
And check First Error Pointer to mark the error occured first.
This FEP is not valid when the corresponing bit of the Uncorrectable
Error Status register is not set, or unimplemented or undefined.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
ERR_{,UN}CORRECTABLE_ERROR_MASK are set of error bits which linux know,
set of PCI_ERR_COR_* and PCI_ERR_UNC_* defined in linux/pci_regs.h.
This masks make aerdrv not to report errors of unknown bit, while aerdrv
have ability to report such undefined errors as "Unknown Error Bit %2d".
OTOH aerdrv_errprint does not have any check of setting in mask register.
So it could report masked wrong error by finding bit in status without
knowing that the bit is masked in the mask register.
This patch changes aerdrv to use mask state in mask register propely
instead of defined/hardcoded ERR_{,UN}CORRECTABLE_ERROR_MASK.
This change prevents aerdrv from reporting masked error, and also enable
reporting unknown errors.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The static buffer errmsg_buff[] is used only for building error
message in fixed format, and is protected by a spinlock.
This patch removes this buffer and the spinlock.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The flag AER_MULTI_ERROR_VALID_FLAG in info->flag does mean that the
root port receives multiple error messages. Error messages can be
posted from different devices, so it does not mean that each reported
device has multiple errors.
If there are multiple error devices and the root port has valid error
source ID, it would be nice to report which device is the error source
reported first.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
In case of multiple errors, struct aer_err_info would be reused among
all reported devices. So the info->status should be initialized before
recycled. Otherwise error of one device might be reported as the error
of another device. Also info->flags has similar problem on reporting
TLP header.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Definitions of MASK macros in aerdrv_errprint.c are tricky and unsafe.
For example, AER_AGENT_TRANSMITTER_MASK(_sev, _stat) does work like:
static inline func(int _sev, int _stat)
{
if (_sev == AER_CORRECTABLE)
return (_stat & (PCI_ERR_COR_REP_ROLL|PCI_ERR_COR_REP_TIMER));
else
return (_stat & PCI_ERR_COR_REP_ROLL);
}
In case of else path here, for uncorrectable errors, testing bits in
_stat by PCI_ERR_COR_* does not make sense because _stat should have only
PCI_ERR_UNC_* bits originated in uncorrectable error status register.
But at this time this is safe because uncorrectable error using bit
position same to PCI_ERR_COR_REP_ROLL(= bit position 8) is not defined.
Likewise, AER_AGENT_COMPLETER_MASK is always PCI_ERR_UNC_COMP_ABORT but
it works because bit 15 of correctable error status is not defined.
It means that these MASK macros will turn to be wrong once if new error
is defined. (In fact, bit 15 of correctable is now defined in PCIe 2.1)
This patch changes these MASK macros to be more strict, not to return
PCI_ERR_COR_* bits for uncorrectable error status and vise versa.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The L0s state can be managed separately for each direction (upstream
direction and downstream direction) of the link. But in the current
implementation, those are mixed up. With this patch, L0s for each
direction are managed separately.
To maintain three states (upstream direction L0s, downstream L0s and
L1), 'aspm_support', 'aspm_enabled', 'aspm_capable', 'aspm_disable'
and 'aspm_default' fields in struct pcie_link_state are changed to
3-bit from 2-bit. The 'latency' field is separated to two 'latency_up'
and 'latency_dw' fields to maintain exit latencies for each direction
of the link. For L0, 'latency_up.l0' and 'latency_dw.l0' are used to
configure upstream direction L0s and downstream direction L0s
respectively. For L1, larger value of 'latency_up.l1' and
'latency_dw.l1' is considered as L1 exit latency.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
In the current implementation, ASPM L0s/L1 is disabled for all links
in the hierarchy if one of the link doesn't meet latency requirement.
But we can partially enable ASPM L0s/L1 on sub-tree in the hierarchy.
This patch allows partial L0s/L1 enablement in the hierarchy. And it
also reduce the calculation cost of ASPM configuration very much.
In the previous implementation, all links were enabled with the same
state. With this patch, enabled state for each link is determined
simply as follows (the 'requested' is from policy_to_aspm_state()).
enabled = requested & (link->aspm_capable & link->aspm_disable)
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Introduce 'aspm_capable' field to maintain the capable ASPM setting of
the link. By the 'aspm_capable', we don't need to recheck latency
every time ASPM policy is changed.
Each bit in 'aspm_capable' is associated to ASPM state (L0S/L1). The
bit is set if the associated ASPM state is supported by the link and
it satisfies the latency requirement (i.e. exit latency < endpoint
acceptable latency). The 'aspm_capable' is updated when
- an endpoint device is added (boot time or hot-plug time)
- an endpoint device is removed (hot-unplug time)
- PCI power state is changed.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Introduce 'aspm_disable' flag to manage disabled ASPM state more
robust way.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Fix possible NULL dereference in pcie_aspm_exit_link_state(). This
patch also cleanup some code.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Remove the following check in __pcie_aspm_config_link() because it
nerver be true.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We must not clear bits in 'aspm_enabled' using 'aspm_support', or
'aspm_enabled' and 'aspm_default' might be different from the actual
state. In addtion, 'aspm_default' should be intialized even if
'aspm_support' is 0.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
By having a pointer to the root port link, we can remove loops in
get_root_port_link() to search the root port link.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We don't need the 'has_switch' field in the struct pcie_link_state.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cleanup for calc_L0S_latency() and calc_L1_latency().
- Separate exit latency and acceptable latency calculation.
- Some minor cleanups.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
In the current ASPM implementation, callers of pcie_set_clock_pm() check
Clock PM capability of the link or current Clock PM state of the link.
This check should be done in pcie_set_clock_pm() itself.
This patch moves those checks into pcie_set_clock_pm(). It also
introduces pcie_set_clkpm_nocheck() that is equivalent to old
pcie_set_clock_pm(), for the caller who wants to change Clocl PM state
regardless of the Clock PM capability or current Clock PM state. In
addition, this patch changes the function name from
pcie_set_clock_pm() to pcie_set_clkpm() for consistency.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Clean up ASPM initialization by refactoring some functionality, renaming
functions, and moving things around.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
In the current ASPM implementation, there are many functions that
take a pointer to struct pci_dev corresponding to the upstream component
of the link as a parameter. But, since those functions handle PCI
express link state, a pointer to struct pcie_link_state is more
suitable than a pointer to struct pci_dev. Changing a parameter to a
pointer to struct pcie_link_state makes ASPM code much simpler and
easier to read. This patch also contains some minor cleanups. This patch
doesn't have any functional change.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cleanup for some fields in pcie_link_state.
- Add comments.
- make "downstream_has_switch" field 1-bit.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The "clk_pm_capable", "clk_pm_enable" and "bios_clk_state" fields in
the struct pcie_link_state only take 1-bit value. So those fields
don't need to be defined as unsigned int. This patch makes those
fields 1-bit, and cleans up some related code.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Clean up latency related data structures for ASPM.
- Introduce struct acpi_latency for exit latency and acceptable
latency management. With this change, struct endpoint_state is no
longer needed.
- We don't need to hold both upstream latency and downstream latency
in the current implementation.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The "support_state", "enabled_state" and "bios_aspm_state" fields in
the struct pcie_link_state take 2-bit value. So those fields don't
need to be defined as unsigned int. This patch makes those fields
2-bit, and cleans up some related code.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Fix a typo in struct pcie_link_state.
The "sibiling" field in the struct pcie_link_state should be
"sibling".
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Debugging PCIE AER code can be very difficult because it is hard
to trigger various real hardware errors. This patch provide a
software based error injection tool, which can fake various PCIE
errors with a user space helper tool named "aer-inject". Which
can be gotten from:
http://www.kernel.org/pub/linux/kernel/people/yhuang/
The patch fakes AER error by faking some PCIE AER related
registers and an AER interrupt for specified the PCIE device.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
When a root port receives the same errors more than once before the
kernel process them, the Multiple Error Messages Received flags are set
by hardware. Because the root port could only save one kind of
correctable error source id and another uncorrectable error source id at
the same time, the second message sender id is lost if the 2 messages
are sent from 2 different devices. This patch makes the kernel search
all devices under the root port when multiple messages are received.
Reviewed-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Zhang Yanmin <yanmin_zhang@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
When the bus id part of error source id is equal to 0 or nosourceid=1,
make the kernel probe the AER status registers of all devices under the
root port to find the initial error reporter.
Reviewed-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Zhang Yanmin <yanmin_zhang@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Based on PCI Express AER specs, a root port might receive multiple
TLP errors while it could only save a correctable error source id
and an uncorrectable error source id at the same time. In addition,
some root port hardware might be unable to provide a correct source
id, i.e., the source id, or the bus id part of the source id provided
by root port might be equal to 0.
The patchset implements the support in kernel by searching the device
tree under the root port.
Patch 1 changes parameter cb of function pci_walk_bus to return a value.
When cb return non-zero, pci_walk_bus stops more searching on the
device tree.
Reviewed-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Zhang Yanmin <yanmin_zhang@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This is used by PCIE AER error injection to fake an PCI AER interrupt.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Adds support for PCI Express transaction layer end-to-end CRC checking
(ECRC). This patch will enable/disable ECRC checking by setting/clearing
the ECRC Check Enable and/or ECRC Generation Enable bits for devices that
support ECRC.
The ECRC setting is controlled by the "pci=ecrc=<policy>" command-line
option. If this option is not set or is set to 'bios", the enable and
generation bits are left in whatever state that firmware/BIOS set them to.
The "off" setting turns them off, and the "on" option turns them on (if the
device supports it).
Turning ECRC on or off can be a data integrity versus performance
tradeoff. In theory, turning it on will catch more data errors, turning
it off means possibly better performance since CRC does not need to be
calculated by the PCIe hardware and packet sizes are reduced.
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
VIA has a strange chipset, it has root port under a bridge. Disable ASPM
for such strange chipset.
Cc: stable@kernel.org
Tested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device. Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used. These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
When an upstream port reports an AER error to root port, kernel
starts error recovery procedures. The default return value of
function pcie_portdrv_slot_reset is PCI_ERS_RESULT_NONE. If all
port service drivers of the downstream port under the upstream
port have no slot_reset method in pci_error_handlers, AER recovery
would stop without resume. Below patch against 2.6.30-rc3 fixes it.
Signed-off-by: Zhang Yanmin <yanmin.zhang@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The PCIe port driver calls pci_enable_device when registering
ports, but never calls pci_disable_device during removal.
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Commit 55633af3 (PCIe portdrv: Use driver data to simplify code)
added a kfree of the driver private data in pcie_port_device_remove
but forgot to remove the old kfree from pcie_portdrv_remove.
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Implement pm object for the PCI Express port driver in order to use
the new power management framework and reduce the code size.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
pcie_port_device_remove currently calls the remove method of port
drivers twice. Ouch!
We are calling device_for_each_child multiple times for no apparent
reason.
So make it simple. Place put_device and device_unregister into
remove_iter, and throw out the rest. Only call device_for_each_child
once.
The code is simpler and actually works!
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
- Rename pci_osc_control_set() to acpi_pci_osc_control_set() according
to the other API names in drivers/acpi/pci_root.c.
- Move _OSC related definitions to include/linux/acpi.h because _OSC
related API is implemented in drivers/acpi/pci_root.c now.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Reviewed-by: Andrew Patterson <andrew.patterson@hp.com>
Tested-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
If MSI-X interrupt mode is used by the PCI Express port driver, too
many vectors are allocated and it is not ensured that the right
vectors will be used for the right services. Namely, the PCI Express
specification states that both PCI Express native PME and PCI Express
hotplug will always use the same MSI or MSI-X message for signalling
interrupts, which implies that the same vector will be used by both
of them. Also, the VC service does not use interrupts at all.
Moreover, is not clear which of the vectors allocated by
pci_enable_msix() in the current code will be used for PME and
hotplug and which of them will be used for AER if all of these
services are configured.
For these reasons, rework the allocation of interrupts for PCI
Express ports so that if MSI-X are enabled, the right vectors will be
used for the right purposes.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The PCI Express port driver uses 'struct pcie_port_service_id' for
matching port service devices and drivers, but this structure
contains fields that duplicate information from the port device
itself (vendor, device, subvendor, subdevice) and fields that are not
used by any existing port service driver (class, class_mask,
drvier_data). Also, both existing port service drivers (AER and
PCIe HP) don't even use the vendor and device fields for device
matching. Therefore 'struct pcie_port_service_id' can be removed
altogether and the only useful members of it (port_type, service) can
be introduced directly into the port service device and port service
driver structures. That simplifies the code quite a bit and reduces
its size.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The second argument of the ->probe() callback in
struct pcie_port_service_driver is unnecessary and never used.
Remove it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The function pcie_portdrv_save_config() in portdrv_pci.c is not
necessary. Remove it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The PCI Express port driver calls pci_enable_device() before setting
up interrupts, which is wrong, because if there is an interrupt pin
configured for the port, pci_enable_device() will likely set up an
interrupt link for it. However, this shouldn't be done if either
MSI or MSI-X interrupt mode is chosen for the port.
The solution is to call pci_enable_device() after setting up
interrupts, because in that case the interrupt link won't be set up
if MSI or MSI-X are enabled.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The PCI Express port driver should not attempt to register service
devices that require the ability to generate interrupts if generating
interrupts is not possible. Namely, if the port has no interrupt pin
configured and we cannot set up MSI or MSI-X for it, there is no way
it can generate interrupts and in such a case the port services that
rely on interrupts (PME, PCIe HP, AER) should not be enabled for it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
PCI Express port driver extension, as defined by struct
pcie_port_device_ext in portdrv.h, is allocated and initialized, but
never used (it also is never freed). Extend it to hold the PCI Express
port type as well as the port interrupt mode, change its name and use it
to simplify the code in portdrv_core.c .
Additionally, remove the redundant interrupt_mode member of struct
pcie_device defined in include/linux/pcieport_if.h .
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The PCIe port driver calls pci_enable_device() during probe but
never calls pci_disable_device() during remove.
Cc: stable@kernel.org
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Commit 47a8b0cc (Enable PCIe AER only after checking firmware
support) wants to walk the PCI bus in the remove path to disable
AER, and calls pci_walk_bus for downstream bridges.
Unfortunately, in the remove path, we remove devices and bridges
in a depth-first manner, starting with the furthest downstream
bridge and working our way backwards.
The furthest downstream bridges will not have a dev->subordinate,
and we hit a NULL deref in pci_walk_bus.
Check for dev->subordinate first before attempting to walk the
PCI hierarchy below us.
Acked-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
The PCIe port driver currently sets the PCIe AER error reporting bits for
any root or switch port without first checking to see if firmware will grant
control. This patch moves setting these bits to the AER service driver
aer_enable_port routine. The bits are then set for the root port and any
downstream switch ports after the check for firmware support (aer_osc_setup)
is made. The patch also unsets the bits in a similar fashion when the AER
service driver is unloaded.
Reviewed-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@hobbes.lan>
Simplify suspend and resume of the PCI Express port driver. It no
longer needs to save and restore the standard configuration space of the
device; this is now done by the PCI PM core layer.
This patch is reported to fix the regression tracked as
http://bugzilla.kernel.org/show_bug.cgi?id=12598
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-and-tested-by: Parag Warudkar <parag.lkml@gmail.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We only want to disable ASPM when the last function is removed from
the parent's device list. We determine this by checking to see if
the parent's device list is completely empty.
Unfortunately, we never hit that code because the parent is considered
an upstream port, and never had an ASPM link_state associated with it.
The early check for !link_state causes us to return early, we never
discover that our device list is empty, and thus we never remove the
downstream ports' link_state nodes.
Instead of checking to see if the parent's device list is empty, we can
check to see if we are the last device on the list, and if so, then we
know that we can clean up properly.
Cc: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The cpu_relax() function can be a noop on certain architectures like
IA-64 when CPU threads are disabled, so use msleep instead during link
retraining busy/wait loop.
Introduce define LINK_RETRAIN_TIMEOUT instead of hard-coding timeout in
pcie_aspm_configure_common_clock.
Use time_after() to avoid jiffy wraparound when checking for expired
timeout.
After timeout expires, recheck link status register link training bit
instead of checking for expired timeout to avoid possible false
positive.
Note that Matthew Wilcox came up with the first rough version of this
patch.
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Add kerneldoc comments to the reamining functions in
drivers/pci/pcie/portdrv_core.c .
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Rearrange code in drivers/pci/pcie/portdrv_bus.c and
drivers/pci/pcie/portdrv_core.c so that related functions and data
structures are closer together.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
There is a problem with the suspend and resume of PCI Express port
service devices that the ->suspend() and ->resume() routines of each
service device are called twice in each suspend-resume cycle, which
is obviously wrong.
The scenario is that first, the PCI Express port driver calls
suspend and resume routines of each port service driver from its
pcie_portdrv_suspend() and pcie_portdrv_resume() callbacks,
respectively (which is correct), and second, the pcie_port_bus_type
driver calls them from its ->suspend() and ->resume() callbacks
(which is not correct, because it doesn't happen at the right time).
The solution is to remove the ->suspend() and ->resume() callbacks
from pcie_port_bus_type and the associated functions.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Add kerneldoc comments to some functions in
drivers/pci/pcie/portdrv_core.c, since the code in there is not
easy to follow without any additional description.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
In a PCIe hierarchy with a switch present, if the link state of an
endpoint device is changed, we must check the whole hierarchy from the
endpoint device to root port, and for each link in the hierarchy, the new
link state should be configured. Previously, the implementation checked
the state but forgot to configure the links between root port to switch.
Fixes Novell bz #448987.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Tested-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Suspend-resume of PCI Express ports has recently been moved into
_suspend_late() and _resume_early() callbacks, but some functions
executed from there should not be called with interrupts disabled,
eg. pci_enable_device(). For this reason, split the suspend-resume
of PCI Express ports into parts to be executed with interrupts
disabled and with interrupts enabled.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
These printks don't contain enough information to be useful. I think it
would be more useful to have a message when a service driver binds to a
root port. That could contain the service type, the interrupt mode and
IRQ, etc.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
I don't see why the suspend and resume of PCI Express ports should be
handled with interrupts enabled and it may even lead to problems in
some situations. For this reason, move the suspending and resuming
of PCI Express ports into ->suspend_late() and ->resume_early()
callbacks executed with interrupts disabled.
This patch addresses the regression from 2.6.26 tracked as
http://bugzilla.kernel.org/show_bug.cgi?id=12121 .
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The _OSC capability OSC_EXT_PCI_CONFIG_SUPPORT is set when the root
bridge is added with pci_acpi_osc_support(), so we no longer need to do
it in the PCIe AER driver.
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The _OSC capabilities OSC_ACTIVE_STATE_PWR_SUPPORT and
OSC_CLOCK_PWR_CAPABILITY_SUPPORT are set when the root bridge is added
with pci_acpi_osc_support(), so we no longer need to do it in the ASPM
driver. Also add the function pcie_aspm_enabled, which returns true if
pcie_aspm=off is not on the kernel command-line.
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch is part of a larger patch series which will remove
the "char bus_id[20]" name string from struct device. The device
name is managed in the kobject anyway, and without any size
limitation, and just needlessly copied into "struct device".
To set and read the device name dev_name(dev) and dev_set_name(dev)
must be used. If your code uses static kobjects, which it shouldn't
do, "const char *init_name" can be used to statically provide the
name the registered device should have. At registration time, the
init_name field is cleared, to enforce the use of dev_name(dev) to
access the device name at a later time.
We need to get rid of all occurrences of bus_id in the entire tree
to be able to enable the new interface. Please apply this patch,
and possibly convert any remaining remaining occurrences of bus_id.
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-Off-By: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
What we have to check here before calling is err_handler->resume, not
->slot_reset. Looks like a copy & paste error from report_slot_reset.
Acked-by: Yanmin Zhang <yanmin.zhang@intel.com>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Makes a Compaq 6735s boot reliably again. It used to hang in the loop
on some boots. Give the link one second to train, otherwise break out
of the loop and reset the previously set clock bits.
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The 'use pci_find_ext_capability everywhere' cleanup brought a new bug,
which makes the AER stop working. Fix it by actually using find_ext_cap
instead of just find_cap. Drop the unused config space size define while
we're at it.
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Remove some open coded (and buggy) versions of pci_find_ext_capability
in favor of the real routine in the PCI core.
Tested-by: Tomasz Czernecki <czernecki@gmail.com>
Acked-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch uniformizes PCI probing debug boot messages with dev_printk()
intead of manual printk()
It changes adress range output from [%llx, %llx] to [%#llx-%#llx], like
in pci_request_region().
For example, it goes from the mixed-style:
PCI: 0000:00:1b.0 reg 10 64bit mmio: [f4280000, f4283fff]
pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
to uniform:
pci 0000:00:1b.0: reg 10 64bit mmio: [0xf4280000-0xf4283fff]
pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
This patch has been runtime tested, boot log messages diffed, everything
looks OK.
Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Vincent Legoll <vincent.legoll@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use "[%04x:%04x]" for PCI vendor/device IDs to follow the format
used by lspci(8).
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
pcie_aspm=force did not work because aspm_force was being double negated
leading to the sanity check failing. Moving a bracket should fix this.
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Consolidate finding of a root bridge and getting its handle to the one
inline function. It's cut & pasted on multiple places. Use this new
inline in those.
Cc: kristen.c.accardi@intel.com
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
A new option, pcie_aspm=force, will force ASPM to be enabled, even on system
with PCIe 1.0 devices.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Disable ASPM on pre-1.1 PCIe devices, as many of them don't implement it
correctly.
Tested-by: Jack Howarth <howarth@bromo.msbb.uc.edu>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The ACPI FADT table includes an ASPM control bit. If the bit is set, do
not enable ASPM since it may indicate that the platform doesn't actually
support the feature.
Tested-by: Jack Howarth <howarth@bromo.msbb.uc.edu>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
While refreshing my physical PCI slot series against upstream, I
noticed a few simple sparse/compile warnings that were easy to
fix.
Fix the following sparse warnings in PCIe:
drivers/pci/pcie/aer/aerdrv.c:86:6: warning: symbol 'pci_no_aer'
was not declared. Should it be static?
drivers/pci/pcie/portdrv_bus.c:21:17: warning: symbol
'pcie_port_bus_type' was not declared. Should it be static?
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The Slot 03:00.* of JMicron controller has two functions, but one is
PCIE endpoint the other isn't PCIE device, very strange. PCIE spec
defines all functions should have the same config for ASPM, so disable
ASPM for the whole slot in this case.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (21 commits)
pciehp: fix error message about getting hotplug control
pci/irq: let pci_device_shutdown to call pci_msi_shutdown v2
pci/irq: restore mask_bits in msi shutdown -v3
doc: replace yet another dev with pdev for consistency in DMA-mapping.txt
PCI: don't expose struct pci_vpd to userspace
doc: fix an incorrect suggestion to pass NULL for PCI like buses
Consistently use pdev as the variable of type struct pci_dev *.
pciehp: Fix command write
shpchp: fix slot name
make pciehp_acpi_get_hp_hw_control_from_firmware()
pciehp: Clean up pcie_init()
pciehp: Mask hotplug interrupt at controller release
pciehp: Remove useless hotplug interrupt enabling
pciehp: Fix wrong slot capability check
pciehp: Fix wrong slot control register access
pciehp: Add missing memory barrier
pciehp: Fix interrupt event handlig
pciehp: fix slot name
Update MAINTAINERS with location of PCI tree
PCI: Add Intel SCH PCI IDs
...
Running 'make oldconfig' I just noticed that PCIEASPM defaults to
'y' in Kconfig even though the feature is both experimental and the
help text recommends that if you are unsure you say 'n'.
It seems to me that this really should default to 'n', not 'y' at the
moment.
The following patch makes that change. Please consider applying.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There's no reason for checking pdev->bus for being NULL here (and we'd
anyway Oops 3 lines below if it was).
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
PCI Express ASPM defines a protocol for PCI Express components in the D0
state to reduce Link power by placing their Links into a low power state
and instructing the other end of the Link to do likewise. This
capability allows hardware-autonomous, dynamic Link power reduction
beyond what is achievable by software-only controlled power management.
However, The device should be configured by software appropriately.
Enabling ASPM will save power, but will introduce device latency.
This patch adds ASPM support in Linux. It introduces a global policy for
ASPM, a sysfs file /sys/module/pcie_aspm/parameters/policy can control
it. The interface can be used as a boot option too. Currently we have
below setting:
-default, BIOS default setting
-powersave, highest power saving mode, enable all available ASPM
state and clock power management
-performance, highest performance, disable ASPM and clock power
management
By default, the 'default' policy is used currently.
In my test, power difference between powersave mode and performance mode
is about 1.3w in a system with 3 PCIE links.
Note: some devices might not work well with aspm, either because chipset
issue or device issue. The patch provide API (pci_disable_link_state),
driver can disable ASPM for specific device.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
#if 0 the no longer used pci_cleanup_aer_correct_error_status().
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[PATCH] pcie AER: don't check _OSC when acpi is disabled
when acpi=off or pci=noacpi, get warning
AER service couldn't init device 0000:00:0a.0:pcie01 - no _OSC support
AER service couldn't init device 0000:00:0e.0:pcie01 - no _OSC support
AER service couldn't init device 0000:00:0f.0:pcie01 - no _OSC support
AER service couldn't init device 0000:80:0b.0:pcie01 - no _OSC support
AER service couldn't init device 0000:80:0e.0:pcie01 - no _OSC support
AER service couldn't init device 0000:80:0f.0:pcie01 - no _OSC support
so don't check _OSC in aer_osc_setup
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts commit 6c723d5bd8.
It caused build errors on non-x86 platforms, config file confusion, and
even some boot errors on some x86-64 boxes. All around, not quite ready
for prime-time :(
Cc: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
PCI Express ASPM defines a protocol for PCI Express components in the D0
state to reduce Link power by placing their Links into a low power state
and instructing the other end of the Link to do likewise. This
capability allows hardware-autonomous, dynamic Link power reduction
beyond what is achievable by software-only controlled power management.
However, The device should be configured by software appropriately.
Enabling ASPM will save power, but will introduce device latency.
This patch adds ASPM support in Linux. It introduces a global policy for
ASPM, a sysfs file /sys/module/pcie_aspm/parameters/policy can control
it. The interface can be used as a boot option too. Currently we have
below setting:
-default, BIOS default setting
-powersave, highest power saving mode, enable all available ASPM
state
and clock power management
-performance, highest performance, disable ASPM and clock power
management
By default, the 'default' policy is used currently.
In my test, power difference between powersave mode and performance mode
is about 1.3w in a system with 3 PCIE links.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
According to the PCI Firmware Specification Revision 3.0 section 4.5, _OSC
should only be called on a root brdige. Here is the relevant passage: "The
_OSC interface defined in this section applies only to Host Bridge ACPI
devices that originate PCI, PCI-X, or PCI Express hierarchies". Changed the
code to find the parent root bridge of the device and call _OSC on that.
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
AER is only used with PCIe devices so we should only check PCIe devices for
_OSC support.
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Native PME is capability of root port or root complex event collector.
It's not determined by PCI PME capability.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The pcie protdrv status can be returned uninitialized,
if there are no children under a device. This leads to
bad responses downstream. Fix this.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For cases in which CONFIG_PCIEAER=y (such as distro kernels), allow users
to disable PCIE Advanced Error Reporting by using "pci=noaer" on the
kernel command line.
This can be used to work around hardware or (kernel) software problems.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove unnecessary CONFIG_HOTPLUG_PCI_PCIE_EVENT_MODE.
The CONFIG_HOTPLUG_PCI_PCIE_POLL_EVENT_MODE option is not needed
because polling mechanism can be enabled through 'pciehp_poll_mode'
module option.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Transform some calls to kmalloc/memset to a single kzalloc (or kcalloc).
Here is a short excerpt of the semantic patch performing
this transformation:
@@
type T2;
expression x;
identifier f,fld;
expression E;
expression E1,E2;
expression e1,e2,e3,y;
statement S;
@@
x =
- kmalloc
+ kzalloc
(E1,E2)
... when != \(x->fld=E;\|y=f(...,x,...);\|f(...,x,...);\|x=E;\|while(...) S\|for(e1;e2;e3) S\)
- memset((T2)x,0,E1);
@@
expression E1,E2,E3;
@@
- kzalloc(E1 * E2,E3)
+ kcalloc(E1,E2,E3)
[akpm@linux-foundation.org: get kcalloc args the right way around]
Signed-off-by: Yoann Padioleau <padator@wanadoo.fr>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Bryan Wu <bryan.wu@analog.com>
Acked-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Dave Airlie <airlied@linux.ie>
Acked-by: Roland Dreier <rolandd@cisco.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Acked-by: Pierre Ossman <drzeus-list@drzeus.cx>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: "David S. Miller" <davem@davemloft.net>
Acked-by: Greg KH <greg@kroah.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Function to clear bogus correctable errors. Analog to pci_aer_uncorrect_are_status.
The Marvell chips seem to start out with a bogus value that needs to be
cleared.
Yanmin ported it to 2.6.22-rc4 by fixing a fuzz patch applying info.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Acked-by: Zhang Yanmin <yanmin.zhang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Below patch fixes aer driver error information and enables aer driver
although CONFIG_ACPI=n.
As a matter of fact, the new patch is created from below 2 patches plus
a minor patch apply fuzz fixing. Because the second patch fixed a compilation
error introduced by the first patch, I merge them to facilitate bisect.
1) http://marc.info/?l=linux-kernel&m=117783233918191&w=2;
2) http://marc.info/?l=linux-mm-commits&m=118046936720790&w=2
Signed-off-by: Zhang Yanmin <yanmin.zhang@intel.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
First thing mm.h does is including sched.h solely for can_do_mlock() inline
function which has "current" dereference inside. By dealing with can_do_mlock()
mm.h can be detached from sched.h which is good. See below, why.
This patch
a) removes unconditional inclusion of sched.h from mm.h
b) makes can_do_mlock() normal function in mm/mlock.c
c) exports can_do_mlock() to not break compilation
d) adds sched.h inclusions back to files that were getting it indirectly.
e) adds less bloated headers to some files (asm/signal.h, jiffies.h) that were
getting them indirectly
Net result is:
a) mm.h users would get less code to open, read, preprocess, parse, ... if
they don't need sched.h
b) sched.h stops being dependency for significant number of files:
on x86_64 allmodconfig touching sched.h results in recompile of 4083 files,
after patch it's only 3744 (-8.3%).
Cross-compile tested on
all arm defconfigs, all mips defconfigs, all powerpc defconfigs,
alpha alpha-up
arm
i386 i386-up i386-defconfig i386-allnoconfig
ia64 ia64-up
m68k
mips
parisc parisc-up
powerpc powerpc-up
s390 s390-up
sparc sparc-up
sparc64 sparc64-up
um-x86_64
x86_64 x86_64-up x86_64-defconfig x86_64-allnoconfig
as well as my two usual configs.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PCIE error output should conform to vendor_id:device_id.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix following section mismatch warning (when compiled with CONFIG_HOTPLUG=n):
WARNING: drivers/pci/built-in.o - Section mismatch: reference to .init.text:aer_probe from .data between 'aerdrv' (at offset 0x1608) and 'aer_error_handlers'
Warning was fixed by renaming aerdrv to aerdriver so we pass the whitelist.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix following section mismatch warning (when compiled with CONFIG_HOTPLUG=n):
WARNING: drivers/pci/built-in.o - Section mismatch: reference to .init.text:pcie_portdrv_probe from .data between 'pcie_portdrv' (at offset 0xe40) and 'pcie_portdrv_err_handler'
This warning was fixed by renaming pcie_portdrv to pcie_portdriver so we pass
the whitelist.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The following warning message should not be displayed for devices
which don't use an interrupt pin.
pcie_portdrv_probe->Dev[XXXX:XXXX] has invalid IRQ. Check vendor BIOS
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Run this:
#!/bin/sh
for f in $(grep -Erl "\([^\)]*\) *k[cmz]alloc" *) ; do
echo "De-casting $f..."
perl -pi -e "s/ ?= ?\([^\)]*\) *(k[cmz]alloc) *\(/ = \1\(/" $f
done
And then go through and reinstate those cases where code is casting pointers
to non-pointers.
And then drop a few hunks which conflicted with outstanding work.
Cc: Russell King <rmk@arm.linux.org.uk>, Ian Molton <spyro@f2s.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Greg KH <greg@kroah.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Paul Fulghum <paulkf@microgate.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Karsten Keil <kkeil@suse.de>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Ian Kent <raven@themaw.net>
Cc: Steven French <sfrench@us.ibm.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Pass the work_struct pointer to the work function rather than context data.
The work function can use container_of() to work out the data.
For the cases where the container of the work_struct may go away the moment the
pending bit is cleared, it is made possible to defer the release of the
structure by deferring the clearing of the pending bit.
To make this work, an extra flag is introduced into the management side of the
work_struct. This governs auto-release of the structure upon execution.
Ordinarily, the work queue executor would release the work_struct for further
scheduling or deallocation by clearing the pending bit prior to jumping to the
work function. This means that, unless the driver makes some guarantee itself
that the work_struct won't go away, the work function may not access anything
else in the work_struct or its container lest they be deallocated.. This is a
problem if the auxiliary data is taken away (as done by the last patch).
However, if the pending bit is *not* cleared before jumping to the work
function, then the work function *may* access the work_struct and its container
with no problems. But then the work function must itself release the
work_struct by calling work_release().
In most cases, automatic release is fine, so this is the default. Special
initiators exist for the non-auto-release case (ending in _NAR).
Signed-Off-By: David Howells <dhowells@redhat.com>
On Thu, 2006-09-28 at 03:42, Olaf Hering wrote:
> PCI-Express AER implemetation: pcie_portdrv error handler
>
> This patch breaks if CONFIG_PM is not enabled,
> pcie_portdrv_restore_config() will be undefined.
I move the definition of pcie_portdrv_restore_config
out of CONFIG_PM.
Below patch is against 2.6.18-mm1. Could you try it?
Signed-off-by: Zhang Yanmin <yanmin.zhang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
__must_check goes on the declaration, not the definition.
Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
Patch 3 implements the core part of PCI-Express AER and aerdrv
port service driver.
When a root port service device is probed, the aerdrv will call
request_irq to register irq handler for AER error interrupt.
When a device sends an PCI-Express error message to the root port,
the root port will trigger an interrupt, by either MSI or IO-APIC,
then kernel would run the irq handler. The handler collects root
error status register and schedules a work. The work will call
the core part to process the error based on its type
(Correctable/non-fatal/fatal).
As for Correctable errors, the patch chooses to just clear the correctable
error status register of the device.
As for the non-fatal error, the patch follows generic PCI error handler
rules to call the error callback functions of the endpoint's driver. If
the device is a bridge, the patch chooses to broadcast the error to
downstream devices.
As for the fatal error, the patch resets the pci-express link and
follows generic PCI error handler rules to call the error callback
functions of the endpoint's driver. If the device is a bridge, the patch
chooses to broadcast the error to downstream devices.
Signed-off-by: Zhang Yanmin <yanmin.zhang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Have pcie_port_bus_register() notice and return errors.
Mark it __must_check so that its caller(s) must check its return value.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If pcie_portdrv_probe() fails but it had already called
pci_enable_device(), then call pci_disable_device() when
returning error.
Is there some reason that this isn't being done?
or was it just missed?
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this patch converts drivers/pci to kzalloc usage.
Compile tested with allyes config.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The bus_id string must be unique for all devices of that bus in the
system, not just for devices with the same parent - otherwise multiple
symlinks with identical names appear in /sys/bus/pci_express/devices.
Signed-off-by: Sergey Vlasov <vsu@altlinux.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I recently picked up my older work to remove unnecessary #includes of
sched.h, starting from a patch by Dave Jones to not include sched.h
from module.h. This reduces the number of indirect includes of sched.h
by ~300. Another ~400 pointless direct includes can be removed after
this disentangling (patch to follow later).
However, quite a few indirect includes need to be fixed up for this.
In order to feed the patches through -mm with as little disturbance as
possible, I've split out the fixes I accumulated up to now (complete for
i386 and x86_64, more archs to follow later) and post them before the real
patch. This way this large part of the patch is kept simple with only
adding #includes, and all hunks are independent of each other. So if any
hunk rejects or gets in the way of other patches, just drop it. My scripts
will pick it up again in the next round.
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In PM v1, all devices were called at SUSPEND_DISABLE level. Then
all devices were called at SUSPEND_SAVE_STATE level, and finally
SUSPEND_POWER_DOWN level. However, with PM v2, to maintain
compatibility for platform devices, I arranged for the PM v2
suspend/resume callbacks to call the old PM v1 suspend/resume
callbacks three times with each level in order so that existing
drivers continued to work.
Since this is obsolete infrastructure which is no longer necessary,
we can remove it. Here's an (untested) patch to do exactly that.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Few more u32 vs. pm_message_t fixes.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch, is based on kernel 2.6.12, provides a fix for PCIe
port bus driver suspend/resume.
Signed-off-by: T. Long Nguyen <tom.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On Friday, March 25, 2005 8:47 PM Greg KH wrote:
>Here's a fix for pci express. For some reason I don't think they are
>using the driver model properly here, but I could be wrong...
Thanks for making the changes. However, changes in functions:
void pcie_port_device_remove(struct pci_dev *dev) and
static int remove_iter(struct device *dev, void *data)
are not correct. Please use the patch, which is based on kernel
2.6.12-rc1, below for a fix for these.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here is the updated patch to get pciehp driver to work for downstream
port of a switch and handle the difference in the offset value of PCI
Express capability list item of different ports.
Signed-off-by: Dely Sy <dely.l.sy@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!