[ Upstream commit 24cfd86433c920188ac3f02df8aba6bc4c792f4b ]
Commits 0077a504e1a4 ("ahci: asm1166: correct count of reported ports")
and 9815e3961754 ("ahci: asm1064: correct count of reported ports")
attempted to limit the ports of the ASM1166 and ASM1064 AHCI controllers
to avoid long boot times caused by the fact that these adapters report
a port map larger than the number of physical ports. The excess ports
are "virtual" to hide port multiplier devices and probing these ports
takes time. However, these commits caused a regression for users that do
use PMP devices, as the ATA devices connected to the PMP cannot be
scanned. These commits have thus been reverted by commit 6cd8adc3e18
("ahci: asm1064: asm1166: don't limit reported ports") to allow the
discovery of devices connected through a port multiplier. But this
revert re-introduced the long boot times for users that do not use a
port multiplier setup.
This patch adds the mask_port_map ahci module parameter to allow users
to manually specify port map masks for controllers. In the case of the
ASMedia 1166 and 1064 controllers, users that do not have port
multiplier devices can mask the excess virtual ports exposed by the
controller to speedup port scanning, thus reducing boot time.
The mask_port_map parameter accepts 2 different formats:
- mask_port_map=<mask>
This applies the same mask to all AHCI controllers
present in the system. This format is convenient for small systems
that have only a single AHCI controller.
- mask_port_map=<pci_dev>=<mask>,<pci_dev>=mask,...
This applies the specified masks only to the PCI device listed. The
<pci_dev> field is a regular PCI device ID (domain🚌dev.func).
This ID can be seen following "ahci" in the kernel messages. E.g.
for "ahci 0000:01:00.0: 2/2 ports implemented (port mask 0x3)", the
<pci_dev> field is "0000:01:00.0".
When used, the function ahci_save_initial_config() indicates that a
port map mask was applied with the message "masking port_map ...".
E.g.: without a mask:
modprobe ahci
dmesg | grep ahci
...
ahci 0000:00:17.0: AHCI vers 0001.0301, 32 command slots, 6 Gbps, SATA mode
ahci 0000:00:17.0: (0000:00:17.0) 8/8 ports implemented (port mask 0xff)
With a mask:
modprobe ahci mask_port_map=0000:00:17.0=0x1
dmesg | grep ahci
...
ahci 0000:00:17.0: masking port_map 0xff -> 0x1
ahci 0000:00:17.0: AHCI vers 0001.0301, 32 command slots, 6 Gbps, SATA mode
ahci 0000:00:17.0: (0000:00:17.0) 1/8 ports implemented (port mask 0x1)
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit eeb25a09c5e0805d92e4ebd12c4b0ad0df1b0295 upstream.
.probe() (ahci_init_one()) calls sysfs_add_file_to_group(), however,
if probe() fails after this call, we currently never call
sysfs_remove_file_from_group().
(The sysfs_remove_file_from_group() call in .remove() (ahci_remove_one())
does not help, as .remove() is not called on .probe() error.)
Thus, if probe() fails after the sysfs_add_file_to_group() call, the next
time we insmod the module we will get:
sysfs: cannot create duplicate filename '/devices/pci0000:00/0000:00:04.0/remapped_nvme'
CPU: 11 PID: 954 Comm: modprobe Not tainted 6.10.0-rc5 #43
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-2.fc40 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0x5d/0x80
sysfs_warn_dup.cold+0x17/0x23
sysfs_add_file_mode_ns+0x11a/0x130
sysfs_add_file_to_group+0x7e/0xc0
ahci_init_one+0x31f/0xd40 [ahci]
Fixes: 894fba7f43 ("ata: ahci: Add sysfs attribute to show remapped NVMe device count")
Cc: stable@vger.kernel.org
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20240629124210.181537-10-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6cd8adc3e18960f6e59d797285ed34ef473cc896 ]
Previously, patches have been added to limit the reported count of SATA
ports for asm1064 and asm1166 SATA controllers, as those controllers do
report more ports than physically having.
While it is allowed to report more ports than physically having in CAP.NP,
it is not allowed to report more ports than physically having in the PI
(Ports Implemented) register, which is what these HBAs do.
(This is a AHCI spec violation.)
Unfortunately, it seems that the PMP implementation in these ASMedia HBAs
is also violating the AHCI and SATA-IO PMP specification.
What these HBAs do is that they do not report that they support PMP
(CAP.SPM (Supports Port Multiplier) is not set).
Instead, they have decided to add extra "virtual" ports in the PI register
that is used if a port multiplier is connected to any of the physical
ports of the HBA.
Enumerating the devices behind the PMP as specified in the AHCI and
SATA-IO specifications, by using PMP READ and PMP WRITE commands to the
physical ports of the HBA is not possible, you have to use the "virtual"
ports.
This is of course bad, because this gives us no way to detect the device
and vendor ID of the PMP actually connected to the HBA, which means that
we can not apply the proper PMP quirks for the PMP that is connected to
the HBA.
Limiting the port map will thus stop these controllers from working with
SATA Port Multipliers.
This patch reverts both patches for asm1064 and asm1166, so old behavior
is restored and SATA PMP will work again, but it will also reintroduce the
(minutes long) extra boot time for the ASMedia controllers that do not
have a PMP connected (either on the PCIe card itself, or an external PMP).
However, a longer boot time for some, is the lesser evil compared to some
other users not being able to detect their drives at all.
Fixes: 0077a504e1a4 ("ahci: asm1166: correct count of reported ports")
Fixes: 9815e3961754 ("ahci: asm1064: correct count of reported ports")
Cc: stable@vger.kernel.org
Reported-by: Matt <cryptearth@googlemail.com>
Signed-off-by: Conrad Kostecki <conikost@gentoo.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
[cassel: rewrote commit message]
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 51af8f255bdaca6d501afc0d085b808f67b44d91 upstream.
ASMedia have confirmed that all ASM106x parts currently listed in
ahci_pci_tbl[] suffer from the 43-bit DMA address limitation that we ran
into on the ASM1061, and therefore, we need to apply the quirk added by
commit 20730e9b2778 ("ahci: add 43-bit DMA address quirk for ASMedia
ASM1061 controllers") to the other supported ASM106x parts as well.
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/linux-ide/ZbopwKZJAKQRA4Xv@x1-carbon/
Signed-off-by: Lennert Buytenhek <kernel@wantstofly.org>
[cassel: add link to ASMedia confirmation email]
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3bf6141060948e27b62b13beb216887f2e54591e upstream.
Add support for PCIe SATA adapter cards based on Asmedia 2116 controllers.
These cards can provide up to 10 SATA ports on PCIe card.
Signed-off-by: Szuying Chen <Chloe_Chen@asmedia.com.tw>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 20730e9b277873deeb6637339edcba64468f3da3 ]
With one of the on-board ASM1061 AHCI controllers (1b21:0612) on an
ASUSTeK Pro WS WRX80E-SAGE SE WIFI mainboard, a controller hang was
observed that was immediately preceded by the following kernel
messages:
ahci 0000:28:00.0: Using 64-bit DMA addresses
ahci 0000:28:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0035 address=0x7fffff00000 flags=0x0000]
ahci 0000:28:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0035 address=0x7fffff00300 flags=0x0000]
ahci 0000:28:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0035 address=0x7fffff00380 flags=0x0000]
ahci 0000:28:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0035 address=0x7fffff00400 flags=0x0000]
ahci 0000:28:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0035 address=0x7fffff00680 flags=0x0000]
ahci 0000:28:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0035 address=0x7fffff00700 flags=0x0000]
The first message is produced by code in drivers/iommu/dma-iommu.c
which is accompanied by the following comment that seems to apply:
/*
* Try to use all the 32-bit PCI addresses first. The original SAC vs.
* DAC reasoning loses relevance with PCIe, but enough hardware and
* firmware bugs are still lurking out there that it's safest not to
* venture into the 64-bit space until necessary.
*
* If your device goes wrong after seeing the notice then likely either
* its driver is not setting DMA masks accurately, the hardware has
* some inherent bug in handling >32-bit addresses, or not all the
* expected address bits are wired up between the device and the IOMMU.
*/
Asking the ASM1061 on a discrete PCIe card to DMA from I/O virtual
address 0xffffffff00000000 produces the following I/O page faults:
vfio-pci 0000:07:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0021 address=0x7ff00000000 flags=0x0010]
vfio-pci 0000:07:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0021 address=0x7ff00000500 flags=0x0010]
Note that the upper 21 bits of the logged DMA address are zero. (When
asking a different PCIe device in the same PCIe slot to DMA to the
same I/O virtual address, we do see all the upper 32 bits of the DMA
address as 1, so this is not an issue with the chipset or IOMMU
configuration on the test system.)
Also, hacking libahci to always set the upper 21 bits of all DMA
addresses to 1 produces no discernible effect on the behavior of the
ASM1061, and mkfs/mount/scrub/etc work as without this hack.
This all strongly suggests that the ASM1061 has a 43 bit DMA address
limit, and this commit therefore adds a quirk to deal with this limit.
This issue probably applies to (some of) the other supported ASMedia
parts as well, but we limit it to the PCI IDs known to refer to
ASM1061 parts, as that's the only part we know for sure to be affected
by this issue at this point.
Link: https://lore.kernel.org/linux-ide/ZaZ2PIpEId-rl6jv@wantstofly.org/
Signed-off-by: Lennert Buytenhek <kernel@wantstofly.org>
[cassel: drop date from error messages in commit log]
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0077a504e1a4468669fd2e011108db49133db56e ]
The ASM1166 SATA host controller always reports wrongly,
that it has 32 ports. But in reality, it only has six ports.
This seems to be a hardware issue, as all tested ASM1166
SATA host controllers reports such high count of ports.
Example output: ahci 0000:09:00.0: AHCI 0001.0301
32 slots 32 ports 6 Gbps 0xffffff3f impl SATA mode.
By adjusting the port_map, the count is limited to six ports.
New output: ahci 0000:09:00.0: AHCI 0001.0301
32 slots 32 ports 6 Gbps 0x3f impl SATA mode.
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=211873
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218346
Signed-off-by: Conrad Kostecki <conikost@gentoo.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
In AHCI 1.3.1, the register description for CAP.SSC:
"When cleared to ‘0’, software must not allow the HBA to initiate
transitions to the Slumber state via agressive link power management nor
the PxCMD.ICC field in each port, and the PxSCTL.IPM field in each port
must be programmed to disallow device initiated Slumber requests."
In AHCI 1.3.1, the register description for CAP.PSC:
"When cleared to ‘0’, software must not allow the HBA to initiate
transitions to the Partial state via agressive link power management nor
the PxCMD.ICC field in each port, and the PxSCTL.IPM field in each port
must be programmed to disallow device initiated Partial requests."
Ensure that we always set the corresponding bits in PxSCTL.IPM, such that
a device is not allowed to initiate transitions to power states which are
unsupported by the HBA.
DevSleep is always initiated by the HBA, however, for completeness, set the
corresponding bit in PxSCTL.IPM such that agressive link power management
cannot transition to DevSleep if DevSleep is not supported.
sata_link_scr_lpm() is used by libahci, ata_piix and libata-pmp.
However, only libahci has the ability to read the CAP/CAP2 register to see
if these features are supported. Therefore, in order to not introduce any
regressions on ata_piix or libata-pmp, create flags that indicate that the
respective feature is NOT supported. This way, the behavior for ata_piix
and libata-pmp should remain unchanged.
This change is based on a patch originally submitted by Runa Guo-oc.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Fixes: 1152b2617a ("libata: implement sata_link_scr_lpm() and make ata_dev_set_feature() global")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Elkhart Lake is the successor of Apollo Lake and Gemini Lake. These
CPUs and their PCHs are used in mobile and embedded environments.
With this patch I suggest that Elkhart Lake SATA controllers [1] should
use the default LPM policy for mobile chipsets.
The disadvantage of missing hot-plug support with this setting should
not be an issue, as those CPUs are used in embedded environments and
not in servers with hot-plug backplanes.
We discovered that the Elkhart Lake SATA controllers have been missing
in ahci.c after a customer reported the throttling of his SATA SSD
after a short period of higher I/O. We determined the high temperature
of the SSD controller in idle mode as the root cause for that.
Depending on the used SSD, we have seen up to 1.8 Watt lower system
idle power usage and up to 30°C lower SSD controller temperatures in
our tests, when we set med_power_with_dipm manually. I have provided a
table showing seven different SATA SSDs from ATP, Intel/Solidigm and
Samsung [2].
Intel lists a total of 3 SATA controller IDs (4B60, 4B62, 4B63) in [1]
for those mobile PCHs.
This commit just adds 0x4b63 as I do not have test systems with 0x4b60
and 0x4b62 SATA controllers.
I have tested this patch with a system which uses 0x4b63 as SATA
controller.
[1] https://sata-io.org/product/8803
[2] https://www.thomas-krenn.com/en/wiki/SATA_Link_Power_Management#Example_LES_v4
Signed-off-by: Werner Fischer <devlists@wefi.net>
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
sata_deb_timing_{hotplug|long|normal}[] store 'unsigned long' debounce
timeouts in ms, while sata_link_debounce() eventually uses those timeouts
by calling ata_{deadline|msleep}( which take just 'unsigned int'. Change
the debounce timeout table element's type to 'unsigned int' -- all these
timeouts happily fit into 'unsigned int'...
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Make it explicit that ATA host templates are not modified.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com> (for DWC AHCI SATA)
Reviewed-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com> (for Tegra)
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: John Garry <john.g.garry@oracle.com>
Cc: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20230322195515.1267197-5-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 104ff59af7 ("ata: ahci: Add Tiger Lake UP{3,4} AHCI
controller") enabled low power mode for the Tiger Lake AHIC adapter in
the author system but created regressions for others. Revert this patch
for now until a better solution is found to make this adapter
eco-friendly.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217114
CC: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Mark the Tiger Lake UP{3,4} AHCI controller as "low_power". This enables
S0ix to work out of the box. Otherwise this isn't working unless the
user manually sets /sys/class/scsi_host/*/link_power_management_policy.
Intel lists a total of 4 SATA controller IDs in [1] for those mobile
PCHs. This commit just adds the "AHCI" variant since I only tested
those.
[1]: https://cdrdv2.intel.com/v1/dl/getContent/631119
Signed-off-by: Simon Gaiser <simon@invisiblethingslab.com>
CC: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Since kernel 5.3.4 my laptop (ICH8M controller) does not see Kingston
SV300S37A60G SSD disk connected into a SATA connector on wake from
suspend. The problem was introduced in c312ef1763 ("libata/ahci: Drop
PCS quirk for Denverton and beyond"): the quirk is not applied on wake
from suspend as it originally was.
It is worth to mention the commit contained another bug: the quirk is
not applied at all to controllers which require it. The fix commit
09d6ac8dc5 ("libata/ahci: Fix PCS quirk application") landed in 5.3.8.
So testing my patch anywhere between commits c312ef1763 and
09d6ac8dc5 is pointless.
Not all disks trigger the problem. For example nothing bad happens with
Western Digital WD5000LPCX HDD.
Test hardware:
- Acer 5920G with ICH8M SATA controller
- sda: some SATA HDD connnected into the DVD drive IDE port with a
SATA-IDE caddy. It is a boot disk
- sdb: Kingston SV300S37A60G SSD connected into the only SATA port
Sample "dmesg --notime | grep -E '^(sd |ata)'" output on wake:
sd 0:0:0:0: [sda] Starting disk
sd 2:0:0:0: [sdb] Starting disk
ata4: SATA link down (SStatus 4 SControl 300)
ata3: SATA link down (SStatus 4 SControl 300)
ata1.00: ACPI cmd ef/03:0c:00:00:00:a0 (SET FEATURES) filtered out
ata1.00: ACPI cmd ef/03:42:00:00:00:a0 (SET FEATURES) filtered out
ata1: FORCE: cable set to 80c
ata5: SATA link down (SStatus 0 SControl 300)
ata3: SATA link down (SStatus 4 SControl 300)
ata3: SATA link down (SStatus 4 SControl 300)
ata3.00: disabled
sd 2:0:0:0: rejecting I/O to offline device
ata3.00: detaching (SCSI 2:0:0:0)
sd 2:0:0:0: [sdb] Start/Stop Unit failed: Result: hostbyte=DID_NO_CONNECT
driverbyte=DRIVER_OK
sd 2:0:0:0: [sdb] Synchronizing SCSI cache
sd 2:0:0:0: [sdb] Synchronize Cache(10) failed: Result:
hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
sd 2:0:0:0: [sdb] Stopping disk
sd 2:0:0:0: [sdb] Start/Stop Unit failed: Result: hostbyte=DID_BAD_TARGET
driverbyte=DRIVER_OK
Commit c312ef1763 dropped ahci_pci_reset_controller() which internally
calls ahci_reset_controller() and applies the PCS quirk if needed after
that. It was called each time a reset was required instead of just
ahci_reset_controller(). This patch puts the function back in place.
Fixes: c312ef1763 ("libata/ahci: Drop PCS quirk for Denverton and beyond")
Signed-off-by: Adam Vodopjan <grozzly@protonmail.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Nothing in this file needs anything from linux/msi.h
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Cc: linux-ide@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
The port base address may be required even before the ata_host instance is
initialized and activated, for instance in the ahci_save_initial_config()
method which we are about to update (consider this modification as a
preparation for that one). Seeing the __ahci_port_base() function isn't
used much it's the best candidate to provide the required functionality.
So let's convert it to accepting the ahci_host_priv structure pointer.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Currently there are four port-map-related fields declared in the
ahci_host_priv structure and used to setup the HBA ports mapping. First
the ports-mapping is read from the PI register and immediately stored in
the saved_port_map field. If forced_port_map is initialized with non-zero
value then its value will have greater priority over the value read from
PI, thus it will override the saved_port_map field. That value will be
then masked by a non-zero mask_port_map field and after some sanity checks
it will be stored in the ahci_host_priv.port_map field as a final port
mapping.
As you can see the logic is a bit too complicated for such a simple task.
We can freely get rid from at least one of the fields with no change to
the implemented semantic. The force_port_map field can be replaced with
taking non-zero saved_port_map value into account. So if saved_port_map is
pre-initialized by the low level drivers (platform drivers) then it will
have greater priority over the value read from PI register and will be
used as actual HBA ports mapping later on. Thus the ports map forcing task
will be just transferred from force_port_map to the saved_port_map field.
This modification will perfectly fit into the feature of having OF-based
initialization of the HW-init HBA CSR fields we are about to introduce in
the next commit.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
The ACPI_FADT_LOW_POWER_S0 flag merely means that it is better to
use low-power S0 idle on the given platform than S3 (provided that
the latter is supported) and it doesn't preclude using either of
them (which of them will be used depends on the choices made by user
space).
For this reason, there is no benefit from checking that flag in
ahci_update_initial_lpm_policy().
First off, it cannot be a bug to do S3 with policy set to either
ATA_LPM_MIN_POWER_WITH_PARTIAL or ATA_LPM_MIN_POWER, because S3 can be
used on systems with ACPI_FADT_LOW_POWER_S0 set and it must work if
really supported, so the ACPI_FADT_LOW_POWER_S0 check is not needed to
protect the S3-capable systems from failing.
Second, suspend-to-idle can be carried out on a system with
ACPI_FADT_LOW_POWER_S0 unset and it is expected to work, so if setting
policy to either ATA_LPM_MIN_POWER_WITH_PARTIAL or ATA_LPM_MIN_POWER is
needed to handle that case correctly, it should be done regardless of
the ACPI_FADT_LOW_POWER_S0 value.
Accordingly, replace the ACPI_FADT_LOW_POWER_S0 check in
ahci_update_initial_lpm_policy() with pm_suspend_default_s2idle()
which is more general and also takes the user's preference into
account and drop the CONFIG_ACPI #ifdef around it that is not necessary
any more.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Intel server platforms that support 'RAID', i.e. have platform firmware
support for software-RAID metadata + features that the kernel also
understands, maintain the same device-ids for RAID from generation to
generation. This is in contrast to client platforms that have tended to
roll new device-ids every platform generation. However, even though
server platform keep the ids there are still unique device-ids per
controller instance. To date there have only been 2 controllers on these
platforms, but platforms code named Emmitsburg add a third controller.
Add the device-id for this third controller and collect it with the
other generic server RAID ids.
As mentioned here [1], the pain of continuing add new and different
device-ids for RAID mode to this file [2] has been heard. Ideally this
device-id would not matter and the class code would remain
PCI_CLASS_STORAGE_SATA_AHCI regardless of the RAID mode, but other
operating systems depend on the class code *not* being AHCI when the
device is in RAID mode. That said, going forward there is little reason
for new server RAID ids to be added as they can simply reuse one of the
existing ids even for a new controller. Server software RAID features
continue to be supported on Linux. Client software RAID features
continue to be not supported and the recommendation there remains to set
the device to AHCI mode in platform firmware.
Link: https://lore.kernel.org/all/8e61fb0104422e8d70701e2ddc7b1ca53f009797.camel@intel.com [1]
Link: https://lore.kernel.org/all/20201119165022.GA3582@infradead.org/ [2]
Cc: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
CONFIG_SATA_LPM_MOBILE_POLICY was renamed to CONFIG_SATA_LPM_POLICY in
commit 4dd4d3deb5 ("ata: ahci: Rename CONFIG_SATA_LPM_MOBILE_POLICY
configuration item").
This can potentially cause problems as users would invisibly lose
configuration policy defaults when they built the new kernel. To
avoid such problems, switch back to the old name (even if it's wrong).
Suggested-by: Christoph Hellwig <hch@infradead.org>
Suggested-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
`CONFIG_SATA_LPM_MOBILE_POLICY` reflects a configuration to apply only to
mobile chipsets. As some desktop boards may want to use this policy by
default as well, rename the configuration item to `SATA_LPM_POLICY`.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
`AHCI_HFLAG_IS_MOBILE` designates that a chipset should be using the
default link power management policy from a kernel configuration item.
As desktop chipsets may also be interested in this default policy
configuration, rename the flag to `AHCI_HFLAG_USE_LPM_POLICY` to more
accurately reflect that a chipset doesn't have to be mobile to adopt it.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
This board definition was originally created for mobile devices to
designate default link power managmeent policy to influence runtime
power consumption.
As this is interesting for more than just mobile designs, rename the
board to `board_ahci_low_power` to make it clear it is about default
policy.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Add the explicit error and status register fields to 'struct ata_taskfile'
using the anonymous *union*s ('struct ide_taskfile' had that for ages!) and
update the libata taskfile code accordingly. There should be no object code
changes resulting from that...
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
ata_host_suspend() always returns 0, so the result checks in many drivers
look pointless. Let's make this function return *void* instead of *int*.
Found by Linux Verification Center (linuxtesting.org) with the SVACE static
analysis tool.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
The 200 ms delay before debouncing the PHY in `sata_link_resume()` is
not needed for the Marvell 88SE9235.
$ lspci -nn -s 0021:0e:00.0
0021:0e:00.0 SATA controller [0106]: Marvell Technology Group Ltd. 88SE9235 PCIe 2.0 x2 4-port SATA 6 Gb/s Controller [1b4b:9235] (rev 11)
So, remove it using the board_ahci_no_debounce_delay board definition.
Tested on IBM S822LC with current Linux 5.17-rc1:
Currently, without this patch (with 200 ms delay), device probe for ata1
takes 485 ms:
[ 3.358158] ata1: SATA max UDMA/133 abar m2048@0x3fe881000000 port 0x3fe881000100 irq 39
[ 3.358175] ata2: SATA max UDMA/133 abar m2048@0x3fe881000000 port 0x3fe881000180 irq 39
[ 3.358191] ata3: SATA max UDMA/133 abar m2048@0x3fe881000000 port 0x3fe881000200 irq 39
[ 3.358207] ata4: SATA max UDMA/133 abar m2048@0x3fe881000000 port 0x3fe881000280 irq 39
[…]
[ 3.677542] ata3: SATA link down (SStatus 0 SControl 300)
[ 3.677719] ata4: SATA link down (SStatus 0 SControl 300)
[ 3.839242] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 3.839828] ata2.00: ATA-10: ST1000NX0313 00LY266 00LY265IBM, BE33, max UDMA/133
[ 3.840029] ata2.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 32), AA
[ 3.841796] ata2.00: configured for UDMA/133
[ 3.843231] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 3.844083] ata1.00: ATA-10: ST1000NX0313 00LY266 00LY265IBM, BE33, max UDMA/133
[ 3.844313] ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 32), AA
[ 3.846043] ata1.00: configured for UDMA/133
With this patch (no delay) device probe for ata1 takes 273 ms:
[ 3.624259] ata1: SATA max UDMA/133 abar m2048@0x3fe881000000 port 0x3f e881000100 irq 39
[ 3.624436] ata2: SATA max UDMA/133 abar m2048@0x3fe881000000 port 0x3f e881000180 irq 39
[ 3.624452] ata3: SATA max UDMA/133 abar m2048@0x3fe881000000 port 0x3f e881000200 irq 39
[ 3.624468] ata4: SATA max UDMA/133 abar m2048@0x3fe881000000 port 0x3f e881000280 irq 39
[…]
[ 3.731966] ata3: SATA link down (SStatus 0 SControl 300)
[ 3.732069] ata4: SATA link down (SStatus 0 SControl 300)
[ 3.897448] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 3.897678] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 3.898140] ata1.00: ATA-10: ST1000NX0313 00LY266 00LY265IBM, BE33, max UDMA/133
[ 3.898175] ata2.00: ATA-10: ST1000NX0313 00LY266 00LY265IBM, BE33, max UDMA/133
[ 3.898287] ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 32), AA
[ 3.898349] ata2.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 32), AA
[ 3.900070] ata1.00: configured for UDMA/133
[ 3.900166] ata2.00: configured for UDMA/133
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Add support for the AMD A85 FCH (Hudson D4) AHCI adapter.
Since this adapter does not require the default 200 ms debounce delay
in sata_link_resume(), create a new board board_ahci_no_debounce_delay
with the link flag ATA_LFLAG_NO_DEBOUNCE_DELAY, and, for now, configure
the AMD A85 FCH (Hudson D4) to use it. On the ASUS F2A85-M PRO it
reduces the Linux kernel boot time by the expected 200 ms from 787 ms
to 585 ms.
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Drop pointless VPRINTK() calls for entering and existing interrupt
routines and convert the remaining calls to dev_dbg().
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
To follow the flow of control we should be using tracepoints, as
they will tie in with the actual I/O flow and deliver a better
overview about what it happening.
This patch adds tracepoints for hard reset, soft reset, and postreset
and adds them in the libata-eh control flow.
With that we can drop the reset DPRINTK calls in the various drivers.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Debugging messages in pci init functions or sg setup are pretty
much pointless, as the workflow pretty much decides what happened.
So drop them.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
AMD requires that the SATA controller be configured for devsleep in order
for S0i3 entry to work properly.
commit b1a9585cc3 ("ata: ahci: Enable DEVSLP by default on x86 with
SLP_S0") sets up a kernel policy to enable devsleep on Intel mobile
platforms that are using s0ix. Add the PCI ID for the SATA controller in
Green Sardine platforms to extend this policy by default for AMD based
systems using s0i3 as well.
Cc: Nehal-bakulchandra Shah <Nehal-bakulchandra.Shah@amd.com>
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=214091
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Add support for PCIe SATA expander cards based on ASMedia 1062 + JBM575
controllers.
These cards can provide up to 10 or more SATA ports on one PCIe card.
Signed-off-by: István Pongrácz <pongracz.istvan@gmail.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Intel devices 0x2822, 0x2823, 0x2826 and 0x2827 are already on the list
as Lewisburg AHCI/RAID. They use same configuration except 0x2822 which
has board_ahci_nosntf (for ICH8).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
This patch enables support for Dell S140 and later controllers
that use Intel's PCHs configured as PCI_CLASS_STORAGE_RAID.
Reviewed-by: Mika Westerberg <mika.westerberg@intel.com>
Signed-off-by: Charles Rose <charles.rose@dell.com>
Link: https://lore.kernel.org/r/20210615190801.1744466-1-charles.rose@dell.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
On Hisilicon Kunpeng920, ESP is set to 1 by default for all ports of
SATA controller. In some scenarios, some ports are not external SATA ports,
and it cause disks connected to these ports to be identified as removable
disks. So disable the SXS capability on the software side to prevent users
from mistakenly considering non-removable disks as removable disks and
performing related operations.
Signed-off-by: Xingui Yang <yangxingui@huawei.com>
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Link: https://lore.kernel.org/r/1615544676-61926-1-git-send-email-luojiaxing@huawei.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add Intel Rocket Lake PCH-H RAID PCI IDs to the list of supported
controllers.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add Intel Comet Lake PCH-U PCI ID to the list of supported controllers.
Set default SATA LPM so the SoC can enter S0ix.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Intel Comet Lake should use the default LPM policy for mobile chipsets.
So, add the PCI ID to the driver list of supported devices.
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add a new sysfs attribute to show how many NVMe devices are remapped.
Userspace like distro installer can use this info to ask user to change
the BIOS setting.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add Intel Comet Lake PCH-V PCI ID to the list of supported controllers.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add Intel Comet Lake PCH-H PCI ID to the list of supported controllers.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add the PCI ID to the driver list to support this new device.
Cc: stable@vger.kernel.org
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Loongson 7A1000 SATA controller uses BAR0 as the base address register.
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
device_shutdown() called from reboot or power_shutdown expect
all devices to be shutdown. Same is true for even ahci pci driver.
As no ahci shutdown function is implemented, the ata subsystem
always remains alive with DMA & interrupt support. File system
related calls should not be honored after device_shutdown().
So defining ahci pci driver shutdown to freeze hardware (mask
interrupt, stop DMA engine and free DMA resources).
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
- improve dma-debug scalability (Eric Dumazet)
- tiny dma-debug cleanup (Dan Carpenter)
- check for vmap memory in dma_map_single (Kees Cook)
- check for dma_addr_t overflows in dma-direct when using
DMA offsets (Nicolas Saenz Julienne)
- switch the x86 sta2x11 SOC to use more generic DMA code
(Nicolas Saenz Julienne)
- fix arm-nommu dma-ranges handling (Vladimir Murzin)
- use __initdata in CMA (Shyam Saini)
- replace the bus dma mask with a limit (Nicolas Saenz Julienne)
- merge the remapping helpers into the main dma-direct flow (me)
- switch xtensa to the generic dma remap handling (me)
- various cleanups around dma_capable (me)
- remove unused dev arguments to various dma-noncoherent helpers (me)
-----BEGIN PGP SIGNATURE-----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=e5wO
-----END PGP SIGNATURE-----
Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux; tag 'dma-mapping-5.5' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- improve dma-debug scalability (Eric Dumazet)
- tiny dma-debug cleanup (Dan Carpenter)
- check for vmap memory in dma_map_single (Kees Cook)
- check for dma_addr_t overflows in dma-direct when using DMA offsets
(Nicolas Saenz Julienne)
- switch the x86 sta2x11 SOC to use more generic DMA code (Nicolas
Saenz Julienne)
- fix arm-nommu dma-ranges handling (Vladimir Murzin)
- use __initdata in CMA (Shyam Saini)
- replace the bus dma mask with a limit (Nicolas Saenz Julienne)
- merge the remapping helpers into the main dma-direct flow (me)
- switch xtensa to the generic dma remap handling (me)
- various cleanups around dma_capable (me)
- remove unused dev arguments to various dma-noncoherent helpers (me)
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux:
* tag 'dma-mapping-5.5' of git://git.infradead.org/users/hch/dma-mapping: (22 commits)
dma-mapping: treat dev->bus_dma_mask as a DMA limit
dma-direct: exclude dma_direct_map_resource from the min_low_pfn check
dma-direct: don't check swiotlb=force in dma_direct_map_resource
dma-debug: clean up put_hash_bucket()
powerpc: remove support for NULL dev in __phys_to_dma / __dma_to_phys
dma-direct: avoid a forward declaration for phys_to_dma
dma-direct: unify the dma_capable definitions
dma-mapping: drop the dev argument to arch_sync_dma_for_*
x86/PCI: sta2x11: use default DMA address translation
dma-direct: check for overflows on 32 bit DMA addresses
dma-debug: increase HASH_SIZE
dma-debug: reorder struct dma_debug_entry fields
xtensa: use the generic uncached segment support
dma-mapping: merge the generic remapping helpers into dma-direct
dma-direct: provide mmap and get_sgtable method overrides
dma-direct: remove the dma_handle argument to __dma_direct_alloc_pages
dma-direct: remove __dma_direct_free_pages
usb: core: Remove redundant vmap checks
kernel: dma-contiguous: mark CMA parameters __initdata/__initconst
dma-debug: add a schedule point in debug_dma_dump_mappings()
...
Using a mask to represent bus DMA constraints has a set of limitations.
The biggest one being it can only hold a power of two (minus one). The
DMA mapping code is already aware of this and treats dev->bus_dma_mask
as a limit. This quirk is already used by some architectures although
still rare.
With the introduction of the Raspberry Pi 4 we've found a new contender
for the use of bus DMA limits, as its PCIe bus can only address the
lower 3GB of memory (of a total of 4GB). This is impossible to represent
with a mask. To make things worse the device-tree code rounds non power
of two bus DMA limits to the next power of two, which is unacceptable in
this case.
In the light of this, rename dev->bus_dma_mask to dev->bus_dma_limit all
over the tree and treat it as such. Note that dev->bus_dma_limit should
contain the higher accessible DMA address.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch adds basic support for Amazon's Annapurna Labs SATA
controller.
Signed-off-by: Hanna Hawa <hhhawa@amazon.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Damien Le Moal