The driver include <linux/gpio.h> yet does not use any
of the symbols from the header, so drop the include.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The driver includes <linux/gpio.h> and <linux/of_gpio.h> yet
fails to use symbols from any of the include files, so drop
these includes.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This driver is using the GPIO descriptor API but yet includes
the legacy <linux/gpio.h> header for no reason. Drop the
surplus include.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The driver include <linux/gpio.h> yet does not use any
of the symbols from the header, so drop the include.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The driver includes <linux/gpio.h> and <linux/of_gpio.h> yet
fails to use symbols from any of the include files, so drop
these includes.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix following checkpatch warning:
CHECK: Alignment should match open parenthesis
+static int st_lsm6dsx_read_event(struct iio_dev *iio_dev,
+ const struct iio_chan_spec *chan,
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The end-of-conversion (EOC) GPIO line is better to grab using
a GPIO descriptor. We drop the pdata for this: clients using board
files can use machine descriptor tables to pass this GPIO from
static data.
Cc: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The device is always in a low-power state due to the hardware design. It
wakes up upon a conversion request and goes back into the low-power
state. The pm ops are added to disable the device completely and to free
the regulator. Disbaling the device completely should be not that
notable but freeing the regulator is important. Because if it is a shared
power-rail the regulator won't be disabled during suspend-to-ram/disk
and so all devices connected to that rail keeps on.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
commit f7072198f2 ("iio: imu: Fix inv_mpu6050 dependencies")
undid the explicit selection of I2C_MUX previously
done by the driver, because I2C_MUX implicitly depended
on HAS_IOMEM.
However commit 93d710a65e ("i2c: mux: fix up dependencies")
cleared up the situation properly and drivers that need
to select I2C_MUX can now do so again.
It makes a lot of sense for a driver to select the driver
infrastructure it needs so restore the natural order of
things.
Cc: Richard Weinberger <richard@nod.at>
Cc: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The channels specification assignment in chip info was simplified.
This patch makes supporting other devices by this driver easier.
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Mixture of old things people have just hit, and a few late breaking
issues with things that went in during the merge window.
Being sent promptly to resolve potential DT breakage causing
issues for binding test builds.
* ad7606
- Avoid reading extra data from the device over what was intended.
* ad7124
- Enable the internal reference when in use.
* ad7292
- Fix up license for newly added binding. Better to not have this go
out in a release with more limited header than intended.
- Fix a constraint on number of channels.
* ad7949
- Fix an issue which can result in readouts being from the wrong channel.
* hdc100x
- Fix wrong ABI usage (units) for relative humidity channel.
* intel mrfld
- Allocate right amount of private data (currently allocating too much).
* ltc2983
- Avoid a potential issue with machine endianness and wrong length device
tree read.
* max1027
- Clean up leak of an iio_trigger on probe failure.
* max9611
- Ensure we sleep long enough to successfully initialize the sensor.
* mpu6050
- Fix wrong ABI usage (units) for temperature channel.
* st_accel
- Fix an unused variable warning.
* st_lsm6dsx
- Fix decimation factor issue that can lead to missaligned datasets
(and hence garbage)
- Fix an issue with how we track enabled fifo channels.
- Avoid powering off the device if wake up events are enabled.
-----BEGIN PGP SIGNATURE-----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=vySY
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-5.5a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of fixes for IIO in the 5.5 cycle.
Mixture of old things people have just hit, and a few late breaking
issues with things that went in during the merge window.
Being sent promptly to resolve potential DT breakage causing
issues for binding test builds.
* ad7606
- Avoid reading extra data from the device over what was intended.
* ad7124
- Enable the internal reference when in use.
* ad7292
- Fix up license for newly added binding. Better to not have this go
out in a release with more limited header than intended.
- Fix a constraint on number of channels.
* ad7949
- Fix an issue which can result in readouts being from the wrong channel.
* hdc100x
- Fix wrong ABI usage (units) for relative humidity channel.
* intel mrfld
- Allocate right amount of private data (currently allocating too much).
* ltc2983
- Avoid a potential issue with machine endianness and wrong length device
tree read.
* max1027
- Clean up leak of an iio_trigger on probe failure.
* max9611
- Ensure we sleep long enough to successfully initialize the sensor.
* mpu6050
- Fix wrong ABI usage (units) for temperature channel.
* st_accel
- Fix an unused variable warning.
* st_lsm6dsx
- Fix decimation factor issue that can lead to missaligned datasets
(and hence garbage)
- Fix an issue with how we track enabled fifo channels.
- Avoid powering off the device if wake up events are enabled.
* tag 'iio-fixes-for-5.5a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio: adc: max9611: Fix too short conversion time delay
iio: ad7949: fix channels mixups
iio: imu: st_lsm6dsx: do not power-off accel if events are enabled
iio: imu: st_lsm6dsx: track hw FIFO buffering with fifo_mask
iio: imu: st_lsm6dsx: fix decimation factor estimation
iio: imu: inv_mpu6050: fix temperature reporting using bad unit
iio: humidity: hdc100x: fix IIO_HUMIDITYRELATIVE channel reporting
iio: adc: max1027: fix not unregistered iio trigger
iio: adc: intel_mrfld_adc: Allocating too much data in probe()
iio: adc: ad7124: Enable internal reference
dt-bindings: iio: adc: ad7292: fix constraint over channel quantity
dt-bindings: iio: adc: ad7292: Update SPDX identifier
iio: temperature: ltc2983: fix u32 read into a unsigned long long
iio: st_accel: Fix unused variable warning
iio: adc: ad7606: fix reading unnecessary data from device
As of commit b9ddd50911 ("iio: adc: max9611: Fix temperature
reading in probe"), max9611 initialization sometimes fails on the
Salvator-X(S) development board with:
max9611 4-007f: Invalid value received from ADC 0x8000: aborting
max9611: probe of 4-007f failed with error -5
The max9611 driver tests communications with the chip by reading the die
temperature during the probe function, which returns an invalid value.
According to the datasheet, the typical ADC conversion time is 2 ms, but
no minimum or maximum values are provided. Maxim Technical Support
confirmed this was tested with temperature Ta=25 degreeC, and promised
to inform me if a maximum/minimum value is available (they didn't get
back to me, so I assume it is not).
However, the driver assumes a 1 ms conversion time. Usually the
usleep_range() call returns after more than 1.8 ms, hence it succeeds.
When it returns earlier, the data register may be read too early, and
the previous measurement value will be returned. After boot, this is
the temperature POR (power-on reset) value, causing the failure above.
Fix this by increasing the delay from 1000-2000 µs to 3000-3300 µs.
Note that this issue has always been present, but it was exposed by the
aformentioned commit.
Fixes: 69780a3bbc ("iio: adc: Add Maxim max9611 ADC driver")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Each time we need to read a sample (from the sysfs interface, since the
driver supports only it) the driver writes the configuration register
with the proper settings needed to perform the said read, then it runs
another xfer to actually read the resulting value. Most notably the
configuration register is updated to set the ADC internal MUX depending by
which channel the read targets.
Unfortunately this seems not enough to ensure correct operation because
the ADC works in a pipelined-like fashion and the new configuration isn't
applied in time.
The ADC alternates two phases: acquisition and conversion. During the
acquisition phase the ADC samples the analog signal in an internal
capacitor; in the conversion phase the ADC performs the actual analog to
digital conversion of the stored voltage. Note that of course the MUX
needs to be set to the proper channel when the acquisition phase is
performed.
Once the conversion phase has been completed, the device automatically
switches back to a new acquisition; on the other hand the device switches
from acquisition to conversion on the rising edge of SPI cs signal (that
is when the xfer finishes).
Only after both two phases have been completed (with the proper settings
already written in the configuration register since the beginning) it is
possible to read the outcome from SPI bus.
With the current driver implementation, we end up in the following
situation:
_______ 1st xfer ____________ 2nd xfer ___________________
SPI cs.. \_________/ \_________/
SPI rd.. idle |(val N-2)+ idle | val N-1 + idle ...
SPI wr.. idle | cfg N + idle | (X) + idle ...
------------------------ + -------------------- + ------------------
AD .. acq N-1 + cnv N-1 | acq N + cnv N | acq N+1
As shown in the diagram above, the value we read in the Nth read belongs
to configuration setting N-1.
In case the configuration is not changed (config[N] == config[N-1]), then
we still get correct data, but in case the configuration changes (i.e.
switching the MUX on another channel), we get wrong data (data from the
previously selected channel).
This patch fixes this by performing one more "dummy" transfer in order to
ending up in reading the data when it's really ready, as per the following
timing diagram.
_______ 1st xfer ____________ 2nd xfer ___________ 3rd xfer ___
SPI cs.. \_________/ \_________/ \_________/
SPI rd.. idle |(val N-2)+ idle |(val N-1)+ idle | val N + ..
SPI wr.. idle | cfg N + idle | (X) + idle | (X) + ..
------------------------ + -------------------- + ------------------- + --
AD .. acq N-1 + cnv N-1 | acq N + cnv N | acq N+1 | ..
NOTE: in the latter case (cfg changes), the acquisition phase for the
value to be read begins after the 1st xfer, that is after the read request
has been issued on sysfs. On the other hand, if the cfg doesn't change,
then we can refer to the fist diagram assuming N == (N - 1); the
acquisition phase _begins_ before the 1st xfer (potentially a lot of time
before the read has been issued via sysfs, but it _ends_ after the 1st
xfer, that is _after_ the read has started. This should guarantee a
reasonably fresh data, which value represents the voltage that the sampled
signal has after the read start or maybe just around it.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Reviewed-by: Charles-Antoine Couret <charles-antoine.couret@essensium.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Do not power-off accel unconditionally if wake-up events are enabled
powering off the hw FIFO. At the same time do not power-off the accel
sensor if it is 'batched' in the hw FIFO disabling sensor events
Fixes: b5969abfa8 ("iio: imu: st_lsm6dsx: add motion events")
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Track hw FIFO state introducing fifo_mask since now the accel sensor
can be enabled during suspend/resume in order to trigger the wake-up
enabling the FIFO in st_lsm6dsx_resume even if it was disabled before
the suspend. Hence we must separately track the fifo state.
Fixes: 4c997dfa69 ("iio: imu: st_lsm6dsx: add wakeup-source option")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix decimation factor and sip estimation for LSM6DSM series
(max value for decimation factor is 32).
If gyro and accel sensors are enabled at 12.5Hz and 416Hz
respectively, decimation factor lookup will fail, producing
unaligned data.
Remove unused decimator filed in st_lsm6dsx_sensor structure.
Fixes: f8710f0357 ("iio: imu: st_lsm6dsx: express odr in mHZ")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Temperature should be reported in milli-degrees, not degrees. Fix
scale and offset values to use the correct unit.
This is a fix for an issue that has been present for a long time.
The fixes tag reflects the point at which the code last changed in a
fashion that would make this fix patch no longer apply. Backports
will be necessary to fix those elements that predate that patch.
Fixes: 1615fe41a1 ("iio: imu: mpu6050: Fix FIFO layout for ICM20602")
Cc: stable@vger.kernel.org
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The IIO_HUMIDITYRELATIVE channel was being incorrectly reported back
as percent when it should have been milli percent. This is via an
incorrect scale value being returned to userspace.
Signed-off-by: Chris Lesiak <chris.lesiak@licor.com>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The driver forgets to unregister the iio trigger in probe failure and
remove.
Use devm API to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This probe function is passing the wrong size to devm_iio_device_alloc().
It is supposed to be the size of the private data. Fortunately,
sizeof(*indio_dev) is larger than sizeof(struct mrfld_adc) so it doesn't
cause a runtime problem.
Fixes: a711866273 ("iio: adc: intel_mrfld_adc: Add Basin Cove ADC driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When the internal reference was selected by a channel it was not enabled.
This patch fixes that and enables it.
Fixes: b3af341bbd ("iio: adc: Add ad7124 support")
Signed-off-by: Mircea Caprioru <mircea.caprioru@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Currently the read of temp using of_property_read_u32_index is reading
a u32 value into a unsigned long long. This relies on machine endianness
to work correctly, so fix this by reading a u32 value and setting temp
to this value.
Addresses-Coverity: ("Reliance on integer endianness")
Fixes: f110f3188e ("iio: temperature: Add support for LTC2983")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
drivers/iio/accel/st_accel_core.c:1005:44: warning:
mount_matrix_ext_info defined but not used [-Wunused-const-variable=]
Using stub helper while CONFIG_ACPI is disabled to fix it.
Suggested-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When a conversion result is being read from ADC, the driver reads the
number of channels + 1 because it thinks that IIO_CHAN_SOFT_TIMESTAMP
is also a physical channel. This patch fixes this issue.
Fixes: 2985a5d884 ("staging: iio: adc: ad7606: Move out of staging")
Reported-by: Robert Wörle <rwoerle@mibtec.de>
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
* CrOS EC / MFD / IIO
- Contains tag-ib-chrome-mfd-iio-input-5.5, which is the first part of a
series from Gwendal to refactor sensor code between MFD, CrOS EC, iio
and input in order to add a new sensorhub driver and FIFO processing
* Wilco EC:
- Add support for Dell's USB PowerShare policy control, keyboard
backlight LED driver, and a new test_event file.
- Fixes use after free in wilco_ec's telemetry driver.
* Misc:
- bugfix in cros_usbpd_logger (missing destroy workqueue).
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQCtZK6p/AktxXfkOlzbaomhzOwwgUCXeaqtwAKCRBzbaomhzOw
wilIAQCQ3/dpAwg2skKYYf3RBLDJeDLA1id7rNSgMOXc2aKyTAD/fCQtNhwj+Hal
W//04WWngTCQF5fkE9OCJrDwbm5eRwc=
=uOGe
-----END PGP SIGNATURE-----
Merge tag 'tag-chrome-platform-for-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux
Pull chrome platform changes from Benson Leung:
"CrOS EC / MFD / IIO:
- Contains tag-ib-chrome-mfd-iio-input-5.5, which is the first part
of a series from Gwendal to refactor sensor code between MFD, CrOS
EC, iio and input in order to add a new sensorhub driver and FIFO
processing
Wilco EC:
- Add support for Dell's USB PowerShare policy control, keyboard
backlight LED driver, and a new test_event file.
- Fixes use after free in wilco_ec's telemetry driver.
Misc:
- bugfix in cros_usbpd_logger (missing destroy workqueue)"
* tag 'tag-chrome-platform-for-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux:
platform/chrome: wilco_ec: fix use after free issue
platform/chrome: cros_ec: Add Kconfig default for cros-ec-sensorhub
Revert "Input: cros_ec_keyb: mask out extra flags in event_type"
Revert "Input: cros_ec_keyb - add back missing mask for event_type"
platform/chrome: cros_ec: handle MKBP more events flag
platform/chrome: cros_ec: Do not attempt to register a non-positive IRQ number
platform/chrome: cros-ec: Record event timestamp in the hard irq
mfd / platform / iio: cros_ec: Register sensor through sensorhub
iio / platform: cros_ec: Add cros-ec-sensorhub driver
mfd / platform: cros_ec: Add sensor_count and make check_features public
platform/chrome: cros_ec: Put docs with the code
platform/chrome: cros_usbpd_logger: add missed destroy_workqueue in remove
platform/chrome: cros_ec: Fix Kconfig indentation
platform/chrome: wilco_ec: Add keyboard backlight LED support
platform/chrome: wilco_ec: Add charging config driver
platform/chrome: wilco_ec: Add Dell's USB PowerShare Policy control
platform/chrome: wilco_ec: Add debugfs test_event file
As part of the cleanup of some remaining y2038 issues, I came to
fs/compat_ioctl.c, which still has a couple of commands that need support
for time64_t.
In completely unrelated work, I spent time on cleaning up parts of this
file in the past, moving things out into drivers instead.
After Al Viro reviewed an earlier version of this series and did a lot
more of that cleanup, I decided to try to completely eliminate the rest
of it and move it all into drivers.
This series incorporates some of Al's work and many patches of my own,
but in the end stops short of actually removing the last part, which is
the scsi ioctl handlers. I have patches for those as well, but they need
more testing or possibly a rewrite.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=lgCl
-----END PGP SIGNATURE-----
Merge tag 'compat-ioctl-5.5' of git://git.kernel.org:/pub/scm/linux/kernel/git/arnd/playground
Pull removal of most of fs/compat_ioctl.c from Arnd Bergmann:
"As part of the cleanup of some remaining y2038 issues, I came to
fs/compat_ioctl.c, which still has a couple of commands that need
support for time64_t.
In completely unrelated work, I spent time on cleaning up parts of
this file in the past, moving things out into drivers instead.
After Al Viro reviewed an earlier version of this series and did a lot
more of that cleanup, I decided to try to completely eliminate the
rest of it and move it all into drivers.
This series incorporates some of Al's work and many patches of my own,
but in the end stops short of actually removing the last part, which
is the scsi ioctl handlers. I have patches for those as well, but they
need more testing or possibly a rewrite"
* tag 'compat-ioctl-5.5' of git://git.kernel.org:/pub/scm/linux/kernel/git/arnd/playground: (42 commits)
scsi: sd: enable compat ioctls for sed-opal
pktcdvd: add compat_ioctl handler
compat_ioctl: move SG_GET_REQUEST_TABLE handling
compat_ioctl: ppp: move simple commands into ppp_generic.c
compat_ioctl: handle PPPIOCGIDLE for 64-bit time_t
compat_ioctl: move PPPIOCSCOMPRESS to ppp_generic
compat_ioctl: unify copy-in of ppp filters
tty: handle compat PPP ioctls
compat_ioctl: move SIOCOUTQ out of compat_ioctl.c
compat_ioctl: handle SIOCOUTQNSD
af_unix: add compat_ioctl support
compat_ioctl: reimplement SG_IO handling
compat_ioctl: move WDIOC handling into wdt drivers
fs: compat_ioctl: move FITRIM emulation into file systems
gfs2: add compat_ioctl support
compat_ioctl: remove unused convert_in_user macro
compat_ioctl: remove last RAID handling code
compat_ioctl: remove /dev/raw ioctl translation
compat_ioctl: remove PCI ioctl translation
compat_ioctl: remove joystick ioctl translation
...
Add support for parallax ping and laser ping sensors with just one pin
for trigger and echo signal.
This driver is based on srf04. In contrast to it it's necessary to
change direction of the pin and to request the irq just for the period
when the echo is rising and falling. Because this adds a lot of cases
there is this individual driver for handling this type of sensors.
Add a new configuration variable CONFIG_PING to Kconfig and Makefile.
Julia reported an issue with failing to unlock a mutex in some error
paths.
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There is no need to explicitly generate update event to update
timer master mode.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Here is the big staging and iio set of patches for the 5.5-rc1 release.
It's the usual huge collection of cleanup patches all over the
drivers/staging/ area, along with a new staging driver, and a bunch of
new IIO drivers as well.
Full details are in the shortlog, but all of these have been in
linux-next for a long time with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXd6lVQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylFnwCgyvZ62uUyQTRey0zvNTe3I4fY9L4AnAnrz3ZC
U6ZA2+Uj3O6qhAr5frRu
=uv8S
-----END PGP SIGNATURE-----
Merge tag 'staging-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging / iio updates from Greg KH:
"Here is the big staging and iio set of patches for the 5.5-rc1
release.
It's the usual huge collection of cleanup patches all over the
drivers/staging/ area, along with a new staging driver, and a bunch of
new IIO drivers as well.
Full details are in the shortlog, but all of these have been in
linux-next for a long time with no reported issues"
* tag 'staging-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (548 commits)
staging: vchiq: Have vchiq_dump_* functions return an error code
staging: vchiq: Refactor indentation in vchiq_dump_* functions
staging: fwserial: Fix Kconfig indentation (seven spaces)
staging: vchiq_dump: Replace min with min_t
staging: vchiq: Fix block comment format in vchiq_dump()
staging: octeon: indent with tabs instead of spaces
staging: comedi: usbduxfast: usbduxfast_ai_cmdtest rounding error
staging: most: core: remove sysfs attr remove_link
staging: vc04: Fix Kconfig indentation
staging: pi433: Fix Kconfig indentation
staging: nvec: Fix Kconfig indentation
staging: most: Fix Kconfig indentation
staging: fwserial: Fix Kconfig indentation
staging: fbtft: Fix Kconfig indentation
fbtft: Drop OF dependency
fbtft: Make use of device property API
fbtft: Drop useless #ifdef CONFIG_OF and dead code
fbtft: Describe function parameters in kernel-doc
fbtft: Make sure string is NULL terminated
staging: rtl8723bs: remove set but not used variable 'change', 'pos'
...
Here is the big set of char/misc and other driver patches for 5.5-rc1
Loads of different things in here, this feels like the catch-all of
driver subsystems these days. Full details are in the shortlog, but
nothing major overall, just lots of driver updates and additions.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXd6ewA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymNXACfebVkDrFOH9EqDgFArPvZ1i9EmZ4AoLbE1Wki
ftJApk+Ov1BT2TvClOza
=cXqg
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big set of char/misc and other driver patches for 5.5-rc1
Loads of different things in here, this feels like the catch-all of
driver subsystems these days. Full details are in the shortlog, but
nothing major overall, just lots of driver updates and additions.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (198 commits)
char: Fix Kconfig indentation, continued
habanalabs: add more protection of device during reset
habanalabs: flush EQ workers in hard reset
habanalabs: make the reset code more consistent
habanalabs: expose reset counters via existing INFO IOCTL
habanalabs: make code more concise
habanalabs: use defines for F/W files
habanalabs: remove prints on successful device initialization
habanalabs: remove unnecessary checks
habanalabs: invalidate MMU cache only once
habanalabs: skip VA block list update in reset flow
habanalabs: optimize MMU unmap
habanalabs: prevent read/write from/to the device during hard reset
habanalabs: split MMU properties to PCI/DRAM
habanalabs: re-factor MMU masks and documentation
habanalabs: type specific MMU cache invalidation
habanalabs: re-factor memory module code
habanalabs: export uapi defines to user-space
habanalabs: don't print error when queues are full
habanalabs: increase max jobs number to 512
...
Drivers:
* test_power: add support for current and charge_counter
* cpcap-charger: improve charge calculation and limit default charge voltage
* ab8500: convert to IIO
* misc. small fixes all over drivers
-----BEGIN PGP SIGNATURE-----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=iHhO
-----END PGP SIGNATURE-----
Merge tag 'for-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
- test_power: add support for current and charge_counter
- cpcap-charger: improve charge calculation and limit default charge
voltage
- ab8500: convert to IIO
- misc small fixes all over drivers
* tag 'for-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (29 commits)
power: supply: bd70528: Add MODULE_ALIAS to allow module auto loading
power: supply: ab8500_charger: Fix inconsistent IS_ERR and PTR_ERR
power: supply: cpcap-charger: cpcap_charger_voltage_to_regval() can be static
power: supply: cpcap-battery: Add basic coulomb counter calibrate support
power: supply: cpcap-battery: Read and save integrator register CCI
power: supply: cpcap-battery: Simplify short term power average calculation
power: supply: cpcap-battery: Simplify coulomb counter calculation with div_s64
power: supply: cpcap-battery: Move coulomb counter units per lsb to ddata
power: supply: cpcap-charger: Allow changing constant charge voltage
power: supply: cpcap-battery: Fix handling of lowered charger voltage
power: supply: cpcap-charger: Improve battery detection
power: supply: cpcap-battery: Check voltage before orderly_poweroff
power: supply: cpcap-charger: Limit voltage to 4.2V for battery
power: supply: ab8500: Handle invalid IRQ from platform_get_irq_byname()
power: supply: ab8500_fg: Do not free non-requested IRQs in probe's error path
power: supply: ab8500: Cleanup probe in reverse order
power: reset: at91: fix __le32 cast in reset code
power: supply: abx500_chargalg: Fix code indentation
mfd: Switch the AB8500 GPADC to IIO
iio: adc: New driver for the AB8500 GPADC
...
Previously, the code was using the of_read_property_bool() to check if
an external regulator was provided. However, this is redundant, as it's
more simple/direct to just ask the regulator is provided, via a
`devm_regulator_get_optional()` call.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
We added a sysfs ABI for getting/setting the type of a thermocouple. This
driver supports chips that support specific fixed thermocouple types; we
cannot set it, but still we can add this sysfs attribute in RO mode to
read-back the thermocouple type.
This driver supports actually several chips:
- max6675
- max31855[k/j/n/s/t/e/r]asa family
Max6675 supports only K-type thermocouples, so we can just report that.
Each chip in max31855 family supports just one specific thermocouple type
(in the obvious way: i.e. max31855jasa supports J-type). This driver did
accept a generic SPI ID and OF compatible "max31855" which does not give
any clue about which chip is really involved (and unfortunately it seems
we have no way to detect it).
This patch introduces a new set of, more specific, SPI IDs and OF
compatible strings to better match the chip type.
The old, generic, "max31855" binding is kept for compatibility reasons, but
this patch aims to deprecate it, so, should we hit it, a warning is spit.
In such case the reported thermocouple type in sysfs is '?', because we
have no way to know.
Regarding the implementation: the thermocouple type information is stored
in the driver private data and I've kept only two maxim_thermocouple_chip
types in order to avoid a lot of duplications (seven chip types with just
a different thermocouple type).
RFT because I have no real HW to test this.
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Patrick Havelange <patrick.havelange@essensium.com>
Cc: Matt Weber <matthew.weber@rockwellcollins.com>
Cc: Matt Ranostay <matt.ranostay@konsulko.com>
Cc: Chuhong Yuan <hslester96@gmail.com>
Cc: Daniel Gomez <dagmcr@gmail.com>
Cc: linux-iio@vger.kernel.org
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The sensor support various thermocouple types (e.g. J, K, N, ...). The
driver allows to configure this parameter using a DT property.
This is useful when i.e. the thermocouple is physically tied to the sensor
and it is usually not removed, or when it is at least known in advance
which sensor will be connected to the circuit.
However, if the user can randomly connect any kind of thermocouples (i.e.
the device exposes a connector, and the user is free to connect its own
sensors), it would be more appropriate to provide a mechanism to
dynamically switch from one thermocouple type to another. This can be i.e.
handled in userspace by a GUI, a configuration file or a program that
detects the thermocouple type by reading a GPIO, or a eeprom on the probe,
or whatever.
This patch adds a IIO attribute that can be used to override, at run-time,
the DT-provided setting (which serves as default).
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Patrick Havelange <patrick.havelange@essensium.com>
Cc: Matt Weber <matthew.weber@rockwellcollins.com>
Cc: Matt Ranostay <matt.ranostay@konsulko.com>
Cc: Chuhong Yuan <hslester96@gmail.com>
Cc: Daniel Gomez <dagmcr@gmail.com>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
We have a couple of thermocouple IIO drivers, supporting several chips.
Some of them support only one specific thermocouple type (e.g. "K", "J"),
one of them can be configured to work with several different thermocouple
types.
In certain applications thermocouples could be externally connected to the
chip by the user.
This patch introduces a new IIO standard attribute to report the supported
thermocouple type and, where applicable, to allow it to be dynamically set
using sysfs.
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Patrick Havelange <patrick.havelange@essensium.com>
Cc: Matt Weber <matthew.weber@rockwellcollins.com>
Cc: Matt Ranostay <matt.ranostay@konsulko.com>
Cc: Chuhong Yuan <hslester96@gmail.com>
Cc: Daniel Gomez <dagmcr@gmail.com>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch introduces IIO_VAL_CHAR type for standard IIO attributes to
allow for attributes that needs to be represented by character rather
than a number. This is preparatory for introducing a new attribute whose
purpose is to describe thermocouple type, that can be i.e. "J", "K", etc..
The char-type value is stored in the first "value" integer that is passed
to the .[read/write]_raw() callbacks.
Note that in order to make it possible for the IIO core to correctly parse
this type (actually, to avoid integer parsing), it became mandatory for
any driver that wish to use IIO_VAL_CHAR on a writable attribute to
implement .write_raw_get_fmt().
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Patrick Havelange <patrick.havelange@essensium.com>
Cc: Matt Weber <matthew.weber@rockwellcollins.com>
Cc: Matt Ranostay <matt.ranostay@konsulko.com>
Cc: Chuhong Yuan <hslester96@gmail.com>
Cc: Daniel Gomez <dagmcr@gmail.com>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This sensor can perform samples averaging in hardware, but currently the
driver leaves this setting alone (default is no averaging).
This patch binds this HW setting to the "oversampling_ratio" IIO attribute
and allows the user to set the averaging as desired (the HW supports
averaging of 2, 5, 8 or 16 samples; in-between values are rounded up).
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Patrick Havelange <patrick.havelange@essensium.com>
Cc: Matt Weber <matthew.weber@rockwellcollins.com>
Cc: Matt Ranostay <matt.ranostay@konsulko.com>
Cc: Chuhong Yuan <hslester96@gmail.com>
Cc: Daniel Gomez <dagmcr@gmail.com>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This sensor has an embedded notch filter for reducing interferences caused
by the power mains. This filter can be tuned to reject either 50Hz or 60Hz
(and harmonics).
Currently the said setting is left alone (the sensor defaults to 60Hz).
This patch introduces a IIO attribute that allows the user to set the said
filter to the desired frequency.
NOTE: this has been intentionally not tied to any DT property to allow
the configuration of this setting from userspace, e.g. with a GUI or by
reading a configuration file, or maybe reading a GPIO tied to a physical
switch or accessing some device that can autodetect the line frequency.
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Patrick Havelange <patrick.havelange@essensium.com>
Cc: Matt Weber <matthew.weber@rockwellcollins.com>
Cc: Matt Ranostay <matt.ranostay@konsulko.com>
Cc: Chuhong Yuan <hslester96@gmail.com>
Cc: Daniel Gomez <dagmcr@gmail.com>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Reviewed-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change uses the ADIS library's state_lock to protect the state of the
`max_speed_hz` change that is done during the set of the sampling
frequency.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It's the only operation that does 2 operations (a read & a write), so the
unlocked functions can be used under a single state lock.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This replaces indio_dev's mlock with the state lock/mutex from the ADIS
library.
The __adis16136_get_freq() function has been prefixed to mark it as
unlocked. The adis16136_{set,get}_filter() functions now hold the state
lock for all the ops that they do.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change removes the use of indio_dev's mlock in favor using the state
lock from the ADIS library.
The set_freq() & get_freq() hooks are unlocked, so they require specific
locking. That is because in some cases the get_freq() hook is used in
combination with adis16400_set_filter().
In cases where only one read/write is done, the functions that hold the
state lock are used.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The single conversion function does a series of reads + writes. This change
extends the use of the state_lock for the entire set of operations.
Previously, indio_dev's mlock was used. This change also removes the use of
this lock.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The initial startup routine is called by some ADIS drivers during probe,
and before registering with IIO. Normally, userspace should not be able to
do any access to the device (as there shouldn't be any available).
This change extends the state lock to the entire initial-startup routine.
Behaviourally nothing should change, but this should make the library
function a bit more robust.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The reset routine may also be important to be protected by the state-lock
and grouped with other operations, so create an unlocked version, so that
this can be done.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This one also gets re-used in certain operations, so it makes sense to
have an unlocked version of this to group it with other
reads/writes/operations to have a single lock for the whole state change.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The adis_enable_irq() does a read & a write. This change keeps a lock for
the duration of both operations vs for each op.
The change is also needed in adis16480, since that has it's own
implementation for adis_enable_irq().
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This will allow more flexible control to group reads & writes into a single
lock (particularly the state_lock).
The end-goal is to remove the indio_dev->mlock usage, and the simplest fix
would have been to just add another lock, which would not be a good idea on
the long-run.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The lock can be extended a bit to protect other elements that are not
particular to just TX/RX. Another idea would have been to just add a new
`state_lock`, but that would mean 2 locks which would be redundant, and
probably cause more potential for dead-locks.
What will be done in the next patches, will be to add some unlocked
versions for read/write_reg functions.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Remove the duplicated code in MFD, since MFD just registers cros-ec-sensorhub
if at least one sensor is present.
Change IIO cros-ec driver to get the pointer to the cros-ec-dev through
cros-ec-sensorhub.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Similar to HID sensor stack, the new driver sits between cros-ec-dev
and the IIO device drivers:
The EC based IIO device topology would be:
iio:device1 ->
...0/0000:00:1f.0/PNP0C09:00/GOOG0004:00/cros-ec-dev.6.auto/
cros-ec-sensorhub.7.auto/
cros-ec-accel.15.auto/
iio:device1
It will be expanded to control EC sensor FIFO.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
[Fix "unknown type name 'uint32_t'" type errors]
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
The relations between enum values and array indices values are currently
not enforced by the code, which makes them fragile w.r.t. future
changes.
Fix this by:
1. Using designated array initializers, to make sure array indices and
enums values match,
2. Linking max9611_csa_gain enum values to the corresponding
max9611_conf_ids enum values, as the latter is cast to the former
in max9611_read_csa_voltage().
No change in generated code.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for driving MPU9150 magnetometer (AK8975) from mpu.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
MPU9150 is i2c only.
Update Kconfig to delete in description chips that are i2c or
spi only.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The scale can now be obtained with the "in_voltage_scale" file.
By default, the scale returned corresponds to the internal VREF of 2.5V.
It is possible to use an external VREF (through the REFIN/REFOUT pin of
the chip), by passing a regulator to the driver. The scale will then be
calculated according to the voltage reported by the regulator.
Signed-off-by: Paul Cercueil <paul.cercueil@analog.com>
Co-developed-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
AD7091R5 is 4-Channel, I2C, Ultra Low Power,12-Bit ADC.
This driver will also support AD7091R2/4/8 in the future.
Datasheet:
Link: https://www.analog.com/media/en/technical-documentation/data-sheets/ad7091r-5.pdf
Signed-off-by: Paul Cercueil <paul.cercueil@analog.com>
Co-developed-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
New device support
* ad5446
- Support the ad5600 DAC (id only needed).
* ad7292 ADC DAC etc
- New driver plus dt-bindings.
* veml6030 ambient light sensor
- New driver plus dt-bindings and sysfs docs.
Features
* mpu6050
- Explicit VDD control.
* stm32-adc
- Allow limiting of max clock frequency from devicetree to ensure it's
suitable for external circuitry.
yaml binding conversions
* ltc1660
* mcp3911
Fixes
* adis16480
- Fix wrong scale factors.
- Fix debugfs reg access by providing the callback.
* cros_ec_baro
- Fixing missing mask entry to make available sample frequencies visible
in sysfs.
* st_lsm6dsx
- Explicitly handle different ODR table sizes.
- Handle restrictions between slave ODR and accel ODR when
both are enabled.
- Allow ODR to be expressed more accurately by using miliHz.
* tools
- Fix an issue with parallel builds.
Cleanups and warning fixes
* adis16136, adis16400, adis16460, adis-lib
- Change some checks on return values to be for 0 rather than strictly
negative. Avoids some fiddly issues with the compiler concluding some
variables are initialized due to a mixture of error checks.
- Assign values only on success of 'read' operations - avoiding any
chance the compiler will falsly suggest they might be used uninitialized.
- Whitespace and simlar cleanups.
* aspeed adc
- devm_platfom_ioremap_resource to reduce boilerplate.
* bcm-iproc-adc
- Stray semicolon removal.
* cc10001
- devm_platfom_ioremap_resource to reduce boilerplate.
* dln2-adc
- Reorganise the buffered mode setup and tear down. Part of moving towards
being able to refactor this area of the IIO core.
* hdc100x
- Reorganise the buffered mode setup and tear down.
* ingenic-adc
- devm_platfom_ioremap_resource to reduce boilerplate.
* lpc18xx-adc
- devm_platfom_ioremap_resource to reduce boilerplate.
* lpc18xx-dac
- devm_platfom_ioremap_resource to reduce boilerplate.
* mt6577
- devm_platfom_ioremap_resource to reduce boilerplate.
* npcm
- devm_platfom_ioremap_resource to reduce boilerplate.
* rcar-gyroadc
- devm_platfom_ioremap_resource to reduce boilerplate.
* spear-adc
- devm_platfom_ioremap_resource to reduce boilerplate.
* vf610-adc
- devm_platfom_ioremap_resource to reduce boilerplate.
* vf610-dac
- devm_platfom_ioremap_resource to reduce boilerplate.
-----BEGIN PGP SIGNATURE-----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=ckQz
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.5c' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Third set of IIO new device support cleanups and fixes for the 5.5 cycle.
New device support
* ad5446
- Support the ad5600 DAC (id only needed).
* ad7292 ADC DAC etc
- New driver plus dt-bindings.
* veml6030 ambient light sensor
- New driver plus dt-bindings and sysfs docs.
Features
* mpu6050
- Explicit VDD control.
* stm32-adc
- Allow limiting of max clock frequency from devicetree to ensure it's
suitable for external circuitry.
yaml binding conversions
* ltc1660
* mcp3911
Fixes
* adis16480
- Fix wrong scale factors.
- Fix debugfs reg access by providing the callback.
* cros_ec_baro
- Fixing missing mask entry to make available sample frequencies visible
in sysfs.
* st_lsm6dsx
- Explicitly handle different ODR table sizes.
- Handle restrictions between slave ODR and accel ODR when
both are enabled.
- Allow ODR to be expressed more accurately by using miliHz.
* tools
- Fix an issue with parallel builds.
Cleanups and warning fixes
* adis16136, adis16400, adis16460, adis-lib
- Change some checks on return values to be for 0 rather than strictly
negative. Avoids some fiddly issues with the compiler concluding some
variables are initialized due to a mixture of error checks.
- Assign values only on success of 'read' operations - avoiding any
chance the compiler will falsly suggest they might be used uninitialized.
- Whitespace and simlar cleanups.
* aspeed adc
- devm_platfom_ioremap_resource to reduce boilerplate.
* bcm-iproc-adc
- Stray semicolon removal.
* cc10001
- devm_platfom_ioremap_resource to reduce boilerplate.
* dln2-adc
- Reorganise the buffered mode setup and tear down. Part of moving towards
being able to refactor this area of the IIO core.
* hdc100x
- Reorganise the buffered mode setup and tear down.
* ingenic-adc
- devm_platfom_ioremap_resource to reduce boilerplate.
* lpc18xx-adc
- devm_platfom_ioremap_resource to reduce boilerplate.
* lpc18xx-dac
- devm_platfom_ioremap_resource to reduce boilerplate.
* mt6577
- devm_platfom_ioremap_resource to reduce boilerplate.
* npcm
- devm_platfom_ioremap_resource to reduce boilerplate.
* rcar-gyroadc
- devm_platfom_ioremap_resource to reduce boilerplate.
* spear-adc
- devm_platfom_ioremap_resource to reduce boilerplate.
* vf610-adc
- devm_platfom_ioremap_resource to reduce boilerplate.
* vf610-dac
- devm_platfom_ioremap_resource to reduce boilerplate.
* tag 'iio-for-5.5c' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (43 commits)
iio: adis16480: Add debugfs_reg_access entry
iio: adis16480: Fix scales factors
tools: iio: Correctly add make dependency for iio_utils
iio: adc: Add driver support for AD7292
dt-bindings: iio: adc: Add dt-schema for AD7292
dt-bindings: iio: adc: Migrate MCP3911 documentation to yaml
iio: imu: mpu6050: Add support for vdd-supply regulator
dt-bindings: iio: imu: mpu6050: add vdd-supply
iio: cros_ec_baro: set info_mask_shared_by_all_available field
iio: dac: ad5446: Add support for new AD5600 DAC
dt-bindings: iio: dac: Migrate LTC1660 documentation to yaml
iio: documentation: light: Add veml6030 sysfs documentation
dt-bindings: iio: light: add veml6030 ALS bindings
iio: light: add driver for veml6030 ambient light sensor
iio: imu: st_lsm6dsx: express odr in mHZ
iio: imu: st_lsm6dsx: fix ODR check in st_lsm6dsx_write_raw
iio: imu: st_lsm6dsx: explicitly define odr table size
iio: adc: stm32: allow to tune analog clock
dt-bindings: iio: stm32-adc: add max clock rate property
iio: dac: vf610: Use devm_platform_ioremap_resource
...
The driver is defining debugfs entries by calling
`adis16480_debugfs_init()`. However, those entries are attached to the
iio_dev debugfs entry which won't exist if no debugfs_reg_access
callback is provided.
Fixes: 2f3abe6cbb ("iio:imu: Add support for the ADIS16480 and similar IMUs")
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch fixes the scales for the gyroscope, accelerometer and
barometer. The pressure scale was just wrong. For the others, the scale
factors were not taking into account that a 32bit word is being read
from the device.
Fixes: 7abad1063d ("iio: adis16480: Fix scale factors")
Fixes: 82e7a1b250 ("iio: imu: adis16480: Add support for ADIS1649x family of devices")
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The AD7292 is a 10-bit monitor and control system with ADC, DACs,
temperature sensor, and GPIOs.
Configure AD7292 devices in direct access mode, enabling single-ended
ADC readings.
Datasheet:
Link: https://www.analog.com/media/en/technical-documentation/data-sheets/ad7292.pdf
Signed-off-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
MPU6050 has two power supply pins: VDD and VLOGIC, but the
mpu6050 driver only supports enabling one of them at the moment.
In some cases, they may need to be enabled separately.
Add an additional "vdd-supply" that stays enabled for as long as
the driver is loaded. We cannot turn off the VDD regulator during
suspend as this would cause register settings (FSR, sampling rate, ...)
to be lost.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Field was already set for light/proximity and
accelerometer/gyroscope/magnetometer sensors.
Fixes: ae7b02ad2f ("iio: common: cros_ec_sensors: Expose cros_ec_sensors frequency range via iio sysfs")
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The AD5600 is a single channel, 16-bit resolution, voltage output digital
to analog converter (DAC). The AD5600 uses a 3-wire SPI interface. It is
part of the AD5541 family of DACs.
The ad5446 IIO driver implements support for some of these DACs (in the
AD5441 family), so the change is a simple entry in this driver.
Link: https://www.analog.com/media/en/technical-documentation/data-sheets/AD5600.pdf
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
veml6030 is an ambient light sensor from Vishay semiconductors.
It has 16-bit resolution, supports both ambient light measurement
and white channel which is more responsive to wider wavelength
spectrum. It has flexible power saving, integration time and
gain options. Communication with host is over I2C.
Signed-off-by: Rishi Gupta <gupt21@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Express available frequencies in mHZ in order to support even
rational ODRs. This patch is need to fix an Android CTS failure
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since st_lsm6dsx i2c master controller relies on accel device as trigger
and slave devices can run at different ODRs we must select an accel_odr >=
slave_odr. Report real accel ODR in st_lsm6dsx_check_odr() in order to
properly set sensor frequency in st_lsm6dsx_write_raw and avoid to
report unsupported frequency
Fixes: 6ffb55e500 ("iio: imu: st_lsm6dsx: introduce ST_LSM6DSX_ID_EXT sensor ids")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Introduce odr_len in st_lsm6dsx_odr_table_entry data structure in order
to explicitly define odr table size and support devices with different
odr table map
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add new optional dt property to tune analog clock prescaler.
Driver looks for optional "st,max-clk-rate-hz", then computes
best approximation below that rate, using ADC internal prescaler.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reduce local boilerplate.
Suggested by coccinelle
CHECK drivers/iio/dac/vf610_dac.c
drivers/iio/dac/vf610_dac.c:189:1-11: WARNING: Use devm_platform_ioremap_resource for info -> regs
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: Sanchayan Maity <maitysanchayan@gmail.com>
Reduce boilerplate.
Suggested by coccinelle
CHECK drivers/iio/dac/lpc18xx_dac.c
drivers/iio/dac/lpc18xx_dac.c:121:1-10: WARNING: Use devm_platform_ioremap_resource for dac -> base
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
CC: Joachim Eastwood <manabian@gmail.com>
Reduces boilerplate.
Suggested by coccinelle
CHECK drivers/iio/adc/vf610_adc.c
drivers/iio/adc/vf610_adc.c:819:1-11: WARNING: Use devm_platform_ioremap_resource for info -> regs
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: Fugang Duan <b38611@freescale.com>
Avoids local boilerplate doing the same thing.
Suggested by coccinelle
CHECK drivers/iio/adc/spear_adc.c
drivers/iio/adc/spear_adc.c:283:1-22: WARNING: Use devm_platform_ioremap_resource for st -> adc_base_spear6xx
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Avoids some local boilerplate.
Suggested by coccinelle.
CHECK drivers/iio/adc/rcar-gyroadc.c
drivers/iio/adc/rcar-gyroadc.c:495:1-11: WARNING: Use devm_platform_ioremap_resource for priv -> regs
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Reduces local boilerplate code.
Suggested by coccinelle via coccicheck.
CHECK drivers/iio/adc/npcm_adc.c
drivers/iio/adc/npcm_adc.c:200:1-11: WARNING: Use devm_platform_ioremap_resource for info -> regs
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: Tomer Maimon <tmaimon77@gmail.com>
Avoid local boilerplate.
Identified by coccinelle
CHECK drivers/iio/adc/lpc18xx_adc.c
drivers/iio/adc/lpc18xx_adc.c:137:1-10: WARNING: Use devm_platform_ioremap_resource for adc -> base
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: Joachim Eastwood <manabian@gmail.com>
Replaces local boilerplate. Identified by coccinelle.
CHECK drivers/iio/adc/ingenic-adc.c
drivers/iio/adc/ingenic-adc.c:449:1-10: WARNING: Use devm_platform_ioremap_resource for adc -> base
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: Artur Rojek <contact@artur-rojek.eu>
Reduces local boilerplate.
Found by coccinelle:
drivers/iio/adc/cc10001_adc.c:344:1-18: WARNING: Use devm_platform_ioremap_resource for adc_dev -> reg_base
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: Naidu Tellapati <naidu.tellapati@imgtec.com>
Reduces boilerplate. Identified by coccinelle
CHECK drivers/iio/adc/mt6577_auxadc.c
drivers/iio/adc/mt6577_auxadc.c:257:1-18: WARNING: Use devm_platform_ioremap_resource for adc_dev -> reg_base
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Zhiyong Tao <zhiyong.tao@mediatek.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reduces boilerplate.
Identified by: Coccinelle / coccicheck
CHECK drivers/iio/adc/aspeed_adc.c
drivers/iio/adc/aspeed_adc.c:189:1-11: WARNING: Use devm_platform_ioremap_resource for data -> base
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Rick Altherr <raltherr@google.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Now that we have symbol namespaces, use them in MCB to not pollute the
default namespace with MCB internals.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Jessica Yu <jeyu@kernel.org>
Reviewed-by: Michael Moese <mmoese@suse.de>
Link: https://lore.kernel.org/r/20191016100158.1400-1-jthumshirn@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This was also caught by the `-Wmaybe-uninitialized` warning, which
(ironically as-is) it makes quite a lot of sense to do for this.
The code that actually calls this function will fail to copy on
the uninitialized value. Hence, patch does not need to go into stable.
Fixes: 78026a6fde ("iio:imu:adis: Add debugfs register access support")
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This was found only after the whole thing with the inline functions, but
the compiler actually found something. The value of the `bias` (in
adis16480_get_calibbias()) should only be set if the read operation was
successful.
No actual known problem occurs as users of this function all
ultimately check the return value. Hence probably not stable material.
Fixes: 2f3abe6cbb ("iio:imu: Add support for the ADIS16480 and similar IMUs")
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This is a typical checkpatch warning. The change just renames the type of
the `freq` var to `unsigned int`.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This is just a minor indentation/alignment fix for the default case of a
switch statement.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADIS library functions return zero on success, and negative values for
error. Positive values aren't returned, but we only care about the success
value (which is zero).
This change is mostly needed so that the compiler won't make any inferences
about some about values being potentially un-initialized. This only
triggers after making some functions inline, because the compiler can
better follow return paths.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADIS library functions return zero on success, and negative values for
error. Positive values aren't returned, but we only care about the success
value (which is zero).
This change is mostly needed so that the compiler won't make any inferences
about some about values being potentially un-initialized. This only
triggers after making some functions inline, because the compiler can
better follow return paths.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADIS library functions return zero on success, and negative values for
error. Positive values aren't returned, but we only care about the success
value (which is zero).
This change is mostly needed so that the compiler won't make any inferences
about some about values being potentially un-initialized. This only
triggers after making some functions inline, because the compiler can
better follow return paths.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADIS library functions return zero on success, and negative values for
error. Positive values aren't returned, but we only care about the success
value (which is zero).
This change is mostly needed so that the compiler won't make any inferences
about some about values being potentially un-initialized. This only
triggers after making some functions inline, because the compiler can
better follow return paths.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADIS library functions return zero on success, and negative values for
error. Positive values aren't returned, but we only care about the success
value (which is zero).
This change is mostly needed so that the compiler won't make any inferences
about some about values being potentially un-initialized. This only
triggers after making some functions inline, because the compiler can
better follow return paths.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The iio_triggered_buffer_postenable() hook should be called first to
attach the poll function and the iio_triggered_buffer_predisable() hook
should be called last in the predisable hook.
This change updates the driver to attach/detach the poll func in the
correct order.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The iio_triggered_buffer_postenable() hook should be called first to
attach the poll function. The iio_triggered_buffer_predisable() hook is
called last (as is it should).
This change moves iio_triggered_buffer_postenable() to be called first. It
adds iio_triggered_buffer_predisable() on the error paths of the postenable
hook.
For the predisable hook, some code-paths have been changed to make sure
that the iio_triggered_buffer_predisable() hook gets called in case there
is an error before it.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support to STM LSM6DSRX 6-axis (acc + gyro) Mems sensor
https://www.st.com/resource/en/datasheet/lsm6dsrx.pdf
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There maybe a race when using dmaengine_terminate_all(). The predisable
routine may call iio_triggered_buffer_predisable() prior to a pending DMA
callback.
Adopt dmaengine_terminate_sync() to ensure there's no pending DMA request
before calling iio_triggered_buffer_predisable().
Fixes: 2763ea0585 ("iio: adc: stm32: add optional dma support")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
None of the ST sensor drivers use any symbols from
<linux/gpio.h>, just drop the include from all of them.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .ioctl and .compat_ioctl file operations have the same prototype so
they can both point to the same function, which works great almost all
the time when all the commands are compatible.
One exception is the s390 architecture, where a compat pointer is only
31 bit wide, and converting it into a 64-bit pointer requires calling
compat_ptr(). Most drivers here will never run in s390, but since we now
have a generic helper for it, it's easy enough to use it consistently.
I double-checked all these drivers to ensure that all ioctl arguments
are used as pointers or are ignored, but are not interpreted as integer
values.
Acked-by: Jason Gunthorpe <jgg@mellanox.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: David Sterba <dsterba@suse.com>
Acked-by: Darren Hart (VMware) <dvhart@infradead.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Set gain in hx711_reset() to its default value after a reset cycle. This
omits one precautionary read cycle, because the read is performed in
hx711_set_gain_for_channel() anyway if gain has changed.
Check for DOUT low and if its high wait some time if it goes down
instead of doing a blind reset cycle when DOUT is not down.
This is a performance optimization which allows to query the sensor with
a higher frequency.
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix the following warnings when documentation is built:
drivers/iio/adc/stm32-adc-core.c:62: warning: cannot understand function
prototype: 'struct stm32_adc_common_regs '
drivers/iio/adc/stm32-adc-core.c:78: warning: cannot understand function
prototype: 'struct stm32_adc_priv_cfg '
drivers/iio/adc/stm32-adc-core.c:123: warning: Function parameter or
member 'pdev' not described in 'stm32f4_adc_clk_sel'
drivers/iio/adc/stm32-adc.c:219: warning: cannot understand function
prototype: 'struct stm32_adc_regs '
drivers/iio/adc/stm32-adc.c:237: warning: cannot understand function
prototype: 'struct stm32_adc_regspec '
drivers/iio/adc/stm32-adc.c:264: warning: cannot understand function
prototype: 'struct stm32_adc_cfg '
drivers/iio/adc/stm32-adc.c:323: warning: Function parameter or member
'difsel' not described in 'N'
drivers/iio/adc/stm32-adc.c:323: warning: Function parameter or member
'pcsel' not described in 'stm32_adc'
drivers/iio/adc/stm32-adc.c:371: warning: cannot understand function
prototype: 'const struct stm32_adc_regs stm32f4_sq[STM32_ADC_MAX_SQ + 1]
drivers/iio/adc/stm32-adc.c:417: warning: cannot understand function
prototype: 'const struct stm32_adc_regs stm32f4_smp_bits[] = '
drivers/iio/adc/stm32-adc.c:508: warning: cannot understand function
prototype: 'const struct stm32_adc_regs stm32h7_smp_bits[] = '
drivers/iio/adc/stm32-adc.c:1112: warning: Function parameter or member
'indio_dev' not described in 'stm32_adc_get_trig_extsel'
drivers/iio/adc/stm32-adc.c:1420: warning: Function parameter or member
'indio_dev' not described in 'stm32_adc_debugfs_reg_access'
drivers/iio/adc/stm32-adc.c:1420: warning: Function parameter or member
'reg' not described in 'stm32_adc_debugfs_reg_access'
drivers/iio/adc/stm32-adc.c:1420: warning: Function parameter or member
'writeval' not described in 'stm32_adc_debugfs_reg_access'
drivers/iio/adc/stm32-adc.c:1420: warning: Function parameter or member
'readval' not described in 'stm32_adc_debugfs_reg_access'
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The iio_triggered_buffer_{predisable,postenable} functions attach/detach
the poll functions.
The iio_triggered_buffer_postenable() should be called before (to attach
the poll func) and then the
The iio_triggered_buffer_predisable() function is hooked directly without
anything, which is probably fine, as the postenable() version seems to also
do some reset/wake-up of the device.
This will mean it will be easier when removing it; i.e. it just gets
removed.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Some chips have a fifo overflow bit issue where the bit is always
set. The result is that every data is dropped.
Change fifo overflow management by checking fifo count against
a maximum value.
Add fifo size in chip hardware set of values.
Fixes: f5057e7b2d ("iio: imu: inv_mpu6050: better fifo overflow handling")
Cc: stable@vger.kernel.org
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Suggestion from coccinelle / coccicheck
CHECK drivers/iio/adc/twl4030-madc.c
drivers/iio/adc/twl4030-madc.c:524:6-15: WARNING: Comparison of 0/1 to bool variable
drivers/iio/adc/twl4030-madc.c:655:1-43: WARNING: Assignment of 0/1 to bool variable
drivers/iio/adc/twl4030-madc.c:659:2-44: WARNING: Assignment of 0/1 to bool variable
drivers/iio/adc/twl4030-madc.c:664:1-43: WARNING: Assignment of 0/1 to bool variable
drivers/iio/adc/twl4030-madc.c:498:2-34: WARNING: Assignment of 0/1 to bool variable
drivers/iio/adc/twl4030-madc.c:510:2-19: WARNING: Assignment of 0/1 to bool variable
drivers/iio/adc/twl4030-madc.c:511:2-11: WARNING: Assignment of 0/1 to bool variable
drivers/iio/adc/twl4030-madc.c:531:2-19: WARNING: Assignment of 0/1 to bool variable
drivers/iio/adc/twl4030-madc.c:532:2-11: WARNING: Assignment of 0/1 to bool variable
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
The LTC2983 is a Multi-Sensor High Accuracy Digital Temperature
Measurement System. It measures a wide variety of temperature sensors and
digitally outputs the result, in °C or °F, with 0.1°C accuracy and
0.001°C resolution. It can measure the temperature of all standard
thermocouples (type B,E,J,K,N,S,R,T), standard 2-,3-,4-wire RTDs,
thermistors and diodes.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
We can drop some duplicate code if we use devm_action for disabling
regulators and pm and the managed variant of iio_device_register().
This allows us to completely remove all remove() callbacks from both
i2c and spi code.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The vddd and vdda supplies are always operated on together. We can
shrink the code a bit by using the bulk regulator helpers.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
FXOS8700CQ is a small, low-power, 3-axis linear accelerometer and 3-axis
magnetometer combined into a single package. The device features a
selectable I2C or point-to-point SPI serial interface with 14-bit
accelerometer and 16-bit magnetometer ADC resolution along with
smart-embedded functions.
FXOS8700CQ has dynamically selectable accelerationfull-scale ranges of
±2 g/±4 g/±8 g and a fixed magnetic measurement range of ±1200 μT.
Output data rates (ODR) from 1.563 Hz to 800 Hz are selectable by the user
for each sensor. Interleaved magnetic and acceleration data is available
at ODR rates of up to 400 Hz. FXOS8700CQ is available in a plastic QFN
package and it is guaranteed to operate over the extended temperature
range of –40 °C to +85 °C.
TODO: Trigger and IRQ configuration support
Datasheet:
http://cache.freescale.com/files/sensors/doc/data_sheet/FXOS8700CQ.pdf
Signed-off-by: Robert Jones <rjones@gateworks.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reduces local boilerplate.
Suggested by coccinelle.
CHECK drivers/iio/adc/xilinx-xadc-core.c
drivers/iio/adc/xilinx-xadc-core.c:1184:1-11: WARNING: Use devm_platform_ioremap_resource for xadc -> base
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Manish Narani <manish.narani@xilinx.com>
Reviewed-by: Sven Van Asbroeck <TheSven73@gmail.com>
Coccinelle noticed:
CHECK drivers/iio/adc/cpcap-adc.c
drivers/iio/adc/cpcap-adc.c:1009:9-34: ERROR: Threaded IRQ with no primary handler requested without IRQF_ONESHOT
As far as I can see this is a simple case of it should be specified
but isn't.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Avoid local boilerplate.
Suggested by coccinelle via coccicheck.
CHECK drivers/iio/adc/meson_saradc.c
drivers/iio/adc/meson_saradc.c:1218:1-5: WARNING: Use devm_platform_ioremap_resource for base
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reduce local boilerplate.
Identified by coccinelle
drivers/iio/adc/exynos_adc.c:792:1-11: WARNING: Use devm_platform_ioremap_resource for info -> regs
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Sparse identified the following
CHECK drivers/iio/proximity/pulsedlight-lidar-lite-v2.c
drivers/iio/proximity/pulsedlight-lidar-lite-v2.c:144:24: warning: cast to restricted __be16
drivers/iio/proximity/pulsedlight-lidar-lite-v2.c:144:24: warning: cast to restricted __be16
drivers/iio/proximity/pulsedlight-lidar-lite-v2.c:144:24: warning: cast to restricted __be16
drivers/iio/proximity/pulsedlight-lidar-lite-v2.c:144:24: warning: cast to restricted __be16
This cleans up by adding a local variable to hold the value whilst
it is __be16 before applying endian converstion into eventual destination.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
There is a somewhat interesting mixture of be16 and le16 going on in
this one function. Changes here formalize that a little more.
CHECK drivers/iio/pressure/bmp280-core.c
drivers/iio/pressure/bmp280-core.c:215:35: warning: cast to restricted __le16
drivers/iio/pressure/bmp280-core.c:229:37: warning: cast to restricted __be16
drivers/iio/pressure/bmp280-core.c:229:37: warning: cast to restricted __be16
drivers/iio/pressure/bmp280-core.c:229:37: warning: cast to restricted __be16
drivers/iio/pressure/bmp280-core.c:229:37: warning: cast to restricted __be16
drivers/iio/pressure/bmp280-core.c:230:36: warning: cast to restricted __be16
drivers/iio/pressure/bmp280-core.c:230:36: warning: cast to restricted __be16
drivers/iio/pressure/bmp280-core.c:230:36: warning: cast to restricted __be16
drivers/iio/pressure/bmp280-core.c:230:36: warning: cast to restricted __be16
drivers/iio/pressure/bmp280-core.c:237:37: warning: cast to restricted __le16
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
This clearly has no actual affect but it does show sparse and similar
static analysers that we are doing this intentionally.
CHECK drivers/iio/gyro/mpu3050-core.c
drivers/iio/gyro/mpu3050-core.c:546:48: warning: incorrect type in assignment (different base types)
drivers/iio/gyro/mpu3050-core.c:546:48: expected restricted __be16 <noident>
drivers/iio/gyro/mpu3050-core.c:546:48: got int
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
When breaking up a constant to write to two 8 bit registers
it isn't obvious to sparse that it was intentional.
CHECK drivers/iio/chemical/sps30.c
drivers/iio/chemical/sps30.c:120:30: warning: cast truncates bits from constant value (8004 becomes 4)
So in the interests of minimising noisy warnings, let us add
a mask.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Tomasz Duszynski <tduszyns@gmail.com>
Nothing stops data being of type __be16, which fixes the warning:
CHECK drivers/iio/adc/stmpe-adc.c
drivers/iio/adc/stmpe-adc.c:202:29: warning: cast to restricted __be16
drivers/iio/adc/stmpe-adc.c:202:29: warning: cast to restricted __be16
drivers/iio/adc/stmpe-adc.c:202:29: warning: cast to restricted __be16
drivers/iio/adc/stmpe-adc.c:202:29: warning: cast to restricted __be16
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: <philippe.schenker@toradex.com>
Cleans up the sparse warning:
CHECK drivers/iio/adc/at91-sama5d2_adc.c
drivers/iio/adc/at91-sama5d2_adc.c:1486:31: warning: Using plain integer as NULL pointer
drivers/iio/adc/at91-sama5d2_adc.c:1509:31: warning: Using plain integer as NULL pointer
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Eugen Hristev <eugen.hristev@microchip.com>
This is a new driver for the ST-Ericsson AB8500 GPADC, which
replaces the old driver in drivers/mfd/ab8500-gpadc.c and
thus gets rid of another necessarily different custom driver
from the times before IIO existed.
The AB8500 GPADC can convert 10 different channels and these
are used for monitoring voltages in the U8500 chipset, some
are used for battery charging, some for temperature
monitoring.
As this is very core functionality that a lot of drivers
depend on and was formerly compiled in with the AB8500 core
driver, we deafault it to 'y' in Kconfig: it can be compiled
out but it is really not advisible: the platform can
for example overheat if we do.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Exposes the ADC device present on, at least, Intel Merrifield platform.
Based on work done by:
Yang Bin <bin.yang@intel.com>
Huiquan Zhong <huiquan.zhong@intel.com>
Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Pavan Kumar S <pavan.kumar.s@intel.com>
Though it has been heavily rewritten for upstream.
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support to STM LSM6DS0 6-axis (acc + gyro) Mems sensor
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix typos in gyro gain definitions for LSM9DS1 sensor
Fixes: 52f4b1f196 ("iio: imu: st_lsm6dsx: add support for accel/gyro unit of lsm9ds1")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change replaces indio_dev's mlock with the driver's own lock. The lock
is mostly needed to protect state when changing the `dac_cache` info.
The lock has been extended to `ad7303_read_raw()`, to make sure that the
cache is updated if an SPI-write is already in progress.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
On LSM6DSO/LSM6DSR/LSM6DSOX/ASM330LHH and ISH330DHCX
devices it is possible to trim the hardware timestamp
resolution through the FREQ_FINE[7:0] bits of the
INTERNAL_FREQ_FINE register, which contains the difference
in percentage of the effective ODR (and timestamp rate)
with respect to the typical value.
The formula for calculating the effective ODR reported
in the application notes has been linearized to the first
order to simplify the calculation (pls. see note on source
code).
This change may be useful in the outcome of CTS
tests regarding the SingleSensorTests and the
SensorTest#testSensorTimeStamps for high ODRs
Signed-off-by: Mario Tesi <mario.tesi@st.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Enable drdy mask if available in order to mark invalid samples during
sensor bootstrap phase
Tested-by: Mario Tesi <mario.tesi@st.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for runtime PM & sleep.
Provide pclk to regmap as registers access doesn't need full power
(e.g. regulator). Always restore HFSEL when resuming. It may get lost
depending on low power level that has been achieved.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add missing wake-up register info for LSM6DSO/LSM6DSOX sensor
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add missing kernel doc for st_lsm6dsx_hw data structure
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add the possibility to enable/disable wakeup source through
st_sensors_platform_data and not only through device tree
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix following checkpatch warnings:
CHECK: Alignment should match open parenthesis
+static int st_lsm6dsx_read_event(struct iio_dev *iio_dev,
+ const struct iio_chan_spec *chan,
CHECK: Alignment should match open parenthesis
+static int st_lsm6dsx_write_event(struct iio_dev *iio_dev,
+ const struct iio_chan_spec *chan,
CHECK: Alignment should match open parenthesis
+static int st_lsm6dsx_read_event_config(struct iio_dev *iio_dev,
+ const struct iio_chan_spec *chan,
CHECK: Alignment should match open parenthesis
+static int st_lsm6dsx_write_event_config(struct iio_dev *iio_dev,
+ const struct iio_chan_spec *chan,
WARNING: line over 80 characters
+ if (dev->of_node && of_property_read_bool(dev->of_node, "wakeup-source"))
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Always grub conf mutex in st_lsm6dsx_write_event_config since it can run
concurrently with FIFO configuration
Fixes: b5969abfa8 ("iio: imu: st_lsm6dsx: add motion events")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Rely on st_lsm6dsx_update_bits_locked in st_lsm6dsx_write_event and
st_lsm6dsx_event_setup routines since they can run concurrently with
sensor hub configuration
Fixes: b5969abfa8 ("iio: imu: st_lsm6dsx: add motion events")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Check if enable_reg of event_settings data structure is defined before
writing on it
Fixes: b5969abfa8 ("iio: imu: st_lsm6dsx: add motion events")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move bdu, boot and reset register definitions in hw_settings register
map since not all supported sensors (e.g lsm9ds1) rely on the same
definitions
Fixes: 52f4b1f196 ("iio: imu: st_lsm6dsx: add support for accel/gyro unit of lsm9ds1")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move active low and open drain register definitions in hw_settings
register map since not all supported sensors (e.g lsm9ds1) rely on the
same definitions
Fixes: 52f4b1f196 ("iio: imu: st_lsm6dsx: add support for accel/gyro unit of lsm9ds1")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Group irq related definition in irq_config structure in
st_lsm6dsx_settings. This is a preliminary patch to move
OpenDrain/Active low registers in st_lsm6dsx_settings.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Check read_fifo pointer before using it since we can't assume it
is always set adding new sensors. This patch fixes the following crash:
irq 277: nobody cared (try booting with the "irqpoll" option)
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.3.0-rc5-00322-g792b824-dirty #7
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
[<c0112750>] (unwind_backtrace) from [<c010d018>] (show_stack+0x10/0x14)
[<c010d018>] (show_stack) from [<c0c2bfc8>] (dump_stack+0xd8/0x10c)
[<c0c2bfc8>] (dump_stack) from [<c01923fc>] (__report_bad_irq+0x24/0xc0)
[<c01923fc>] (__report_bad_irq) from [<c0192820>] (note_interrupt+0x27c/0x2dc)
[<c0192820>] (note_interrupt) from [<c018f174>] (handle_irq_event_percpu+0x54/0x7c)
[<c018f174>] (handle_irq_event_percpu) from [<c018f1d4>] (handle_irq_event+0x38/0x5c)
[<c018f1d4>] (handle_irq_event) from [<c0193664>] (handle_level_irq+0xc8/0x154)
[<c0193664>] (handle_level_irq) from [<c018df58>] (generic_handle_irq+0x20/0x34)
[<c018df58>] (generic_handle_irq) from [<c053c348>] (mxc_gpio_irq_handler+0xc4/0xf8)
[<c053c348>] (mxc_gpio_irq_handler) from [<c053c3e0>] (mx3_gpio_irq_handler+0x64/0xb8)
[<c053c3e0>] (mx3_gpio_irq_handler) from [<c018df58>] (generic_handle_irq+0x20/0x34)
[<c018df58>] (generic_handle_irq) from [<c018e550>] (__handle_domain_irq+0x64/0xe0)
[<c018e550>] (__handle_domain_irq) from [<c0529610>] (gic_handle_irq+0x4c/0xa0)
[<c0529610>] (gic_handle_irq) from [<c0101a70>] (__irq_svc+0x70/0x98)
Exception stack(0xc1301f10 to 0xc1301f58
1f00: 00000001 00000006 00000000 c130c340
1f20: c1300000 c1308928 00000001 c1308960 00000000 c12b9db0 c1308908 00000000
1f40: 00000000 c1301f60 c0182010 c0109508 20000013 ffffffff
[<c0101a70>] (__irq_svc) from [<c0109508>] (arch_cpu_idle+0x20/0x3c)
[<c0109508>] (arch_cpu_idle) from [<c015ed70>] (do_idle+0x1bc/0x2bc)
[<c015ed70>] (do_idle) from [<c015f204>] (cpu_startup_entry+0x18/0x1c)
[<c015f204>] (cpu_startup_entry) from [<c1200e68>] (start_kernel+0x440/0x504)
[<c1200e68>] (start_kernel) from [<00000000>] (0x0)
handlers:
[<62052c0d>] st_lsm6dsx_handler_irq threaded
[<f2004b92>] st_lsm6dsx_handler_thread
Fixes: 52f4b1f196 ("iio: imu: st_lsm6dsx: add support for accel/gyro unit of lsm9ds1")
Tested-by: Bobby Jones <rjones@gateworks.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Rely on st_lsm6dsx_read_locked in st_lsm6dsx_report_motion_event since
it can run concurrently with sensor hub configuration. Move event
related code in st_lsm6dsx_report_motion_event
Fixes: 1aabad1fb5 ("iio: imu: st_lsm6dsx: add motion report function and call from interrupt")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Maxim's max12xx series is very similar to the max10xx series, with the
difference of the measurements depth which is upgraded from 10 to 12
bits per channel. Everything else looks the same.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Maxim's max1027/29/31 series returns the measured voltages with a
resolution of 10 bits. There is a very similar series, max1227/29/31
which works identically but uses a resolution of 12 bits. Prepare the
support for these chips by turning the 'depth' into a macro parameter
instead of hardcoding it everywhere. Also reorganize just a bit the
macros at the top to avoid repeating tens of lines when adding support
for a new chip.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
All the registers are configured by the driver, let's reset the chip
at probe time, avoiding any conflict with a possible earlier
configuration.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The chip has a 'start conversion' and a 'end of conversion' pair of
pins. They can be used but this is absolutely not mandatory as regular
polling of the value is totally fine with the current internal
clocking setup. Turn the interrupts optional and do not error out if
they are not inquired in the device tree. This has the effect to
prevent triggered buffers use though.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Until now, only write operations were supported. Force two bytes read
operation when reading, which should fit most of the development
purposes. Of course, extended operations like buffered reads on
multiple channels or even temperature + voltage reads will not be read
entirely. Usually, just starting a new operation will work but in any
case a software reset (done through the debufs interface too) will
return the device in a usable state.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add initial support for Analog Devices ADUX1020 Photometric sensor.
Only proximity mode has been enabled for now.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since the logic for `spi_delay` struct + `spi_delay_exec()` has been copied
from the `cs_change_delay` logic, it's natural to make this delay, the
first user.
The `cs_change_delay` logic requires that the default remain 10 uS, in case
it is unspecified/unconfigured. So, there is some special handling needed
to do that.
The ADIS library is one of the few users of the new `cs_change_delay`
parameter for an spi_transfer.
The introduction of the `spi_delay` struct, requires that the users of of
`cs_change_delay` get an update. This change also updates the ADIS library.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-4-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Third version with the adis rework set dropped as better to just have
a fresh version of that at some future date.
The usual mixed backs of new device support being added to drivers,
long term reworks continuing and little per driver cleanups and
features.
Also a few trivial counter subsystem tidy ups on behalf of William.
Core new feature
* Device label support. A long requested feature no one got around to
implementing before. Allows DT based provision of a 'label' that
identifies a device uniquely within a system. This differs from existing
'name' which is meant to be the part number.
New device support
* ingenic-adc
- Support for the JZ4770 SoC ADC including bindings.
* inv_mpu6050
- Add support for magnetometer in MPU925x parts.
Fiddly to do as this is actually a separate device sitting inside the
package, but with the master device being able to schedule reads etc.
Will only run if the auxiliary bus is not in use for any other devices.
Features
* ad7192
- Userspace calibration controls to do zero and full scale.
* st_lsm6dsx
- Enable latched interrupts by default for sensors events with related clear.
- Motion events and related wakeup source. This needed quite a bit of
refactoring as well.
Cleanups and minor features
* ad7192
- sysfs ABI docs
* ad7949
- Remove code to readback configuration word as driver never actually enabled
it.
- Fix incorrect xfer length. Not actually known to cause problems other
than wasted bus usage.
* adis16080
- Replace core mlock usage with local lock with more appropriate scope.
* adis16130
- Remove pointless mlock usage.
* adis16240
- Remove include of gpio.h as no gpio usage.
* atlas-ph-sensor
- Improve logical ordering of buffer predisable / postenable functions.
This is part of a longer term rework Alexandru is driving towards.
* bh1750
- Fix up a static compiler warning and make the code more readable.
- yaml conversion of binding + MAINTAINERS entry.
* bmp280
- Drop a stray newline.
* cm36651
- Drop a redundant assignment
* itg3200
- Alignment cleanup.
* max31856
- Add missing of_node and parent references, useful to identify the device.
* sc27xx_adc
- Use devm_hwspin_lock_request_specific rather than local rolled version.
* stm32-lptimer counter
- kernel-doc warning.
* stm32-timer counter
- kernel-doc warning.
- Alignment cleanup.
* sx9500
- Improve logical ordering of buffer predisable / postenable functions.
This is part of a longer term rework Alexandru is driving towards.
* tcs3414
- Improve logical ordering of buffer predisable / postenable functions.
This is part of a longer term rework Alexandru is driving towards.
-----BEGIN PGP SIGNATURE-----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=nIWU
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.5a-take3' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First set of IIO new device support, cleanups and features for the 5.5 cycle
Third version with the adis rework set dropped as better to just have
a fresh version of that at some future date.
The usual mixed backs of new device support being added to drivers,
long term reworks continuing and little per driver cleanups and
features.
Also a few trivial counter subsystem tidy ups on behalf of William.
Core new feature
* Device label support. A long requested feature no one got around to
implementing before. Allows DT based provision of a 'label' that
identifies a device uniquely within a system. This differs from existing
'name' which is meant to be the part number.
New device support
* ingenic-adc
- Support for the JZ4770 SoC ADC including bindings.
* inv_mpu6050
- Add support for magnetometer in MPU925x parts.
Fiddly to do as this is actually a separate device sitting inside the
package, but with the master device being able to schedule reads etc.
Will only run if the auxiliary bus is not in use for any other devices.
Features
* ad7192
- Userspace calibration controls to do zero and full scale.
* st_lsm6dsx
- Enable latched interrupts by default for sensors events with related clear.
- Motion events and related wakeup source. This needed quite a bit of
refactoring as well.
Cleanups and minor features
* ad7192
- sysfs ABI docs
* ad7949
- Remove code to readback configuration word as driver never actually enabled
it.
- Fix incorrect xfer length. Not actually known to cause problems other
than wasted bus usage.
* adis16080
- Replace core mlock usage with local lock with more appropriate scope.
* adis16130
- Remove pointless mlock usage.
* adis16240
- Remove include of gpio.h as no gpio usage.
* atlas-ph-sensor
- Improve logical ordering of buffer predisable / postenable functions.
This is part of a longer term rework Alexandru is driving towards.
* bh1750
- Fix up a static compiler warning and make the code more readable.
- yaml conversion of binding + MAINTAINERS entry.
* bmp280
- Drop a stray newline.
* cm36651
- Drop a redundant assignment
* itg3200
- Alignment cleanup.
* max31856
- Add missing of_node and parent references, useful to identify the device.
* sc27xx_adc
- Use devm_hwspin_lock_request_specific rather than local rolled version.
* stm32-lptimer counter
- kernel-doc warning.
* stm32-timer counter
- kernel-doc warning.
- Alignment cleanup.
* sx9500
- Improve logical ordering of buffer predisable / postenable functions.
This is part of a longer term rework Alexandru is driving towards.
* tcs3414
- Improve logical ordering of buffer predisable / postenable functions.
This is part of a longer term rework Alexandru is driving towards.
* tag 'iio-for-5.5a-take3' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (41 commits)
iio: pressure: bmp280: remove stray newline
iio: adc: sc27xx: Use devm_hwspin_lock_request_specific() to simplify code
iio: chemical: atlas-ph-sensor: fix iio_triggered_buffer_predisable() position
iio: gyro: clean up indentation issue
counter: stm32: clean up indentation issue
iio: proximity: sx9500: fix iio_triggered_buffer_{predisable,postenable} positions
iio: core: Add optional symbolic label to device attributes
dt-binding: iio: Add optional label property
iio: gyro: adis16080: replace mlock with own lock
counter: stm32-lptimer-cnt: fix a kernel-doc warning
counter: stm32-timer-cnt: fix a kernel-doc warning
iio: gyro: adis16130: remove mlock usage
MAINTAINERS: add entry for ROHM BH1750 driver
dt-bindings: iio: light: bh1750: convert bindings to yaml
iio: imu: st_lsm6dsx: add motion report function and call from interrupt
iio: imu: st_lsm6dsx: always enter interrupt thread
iio: imu: st_lsm6dsx: add wakeup-source option
iio: imu: st_lsm6dsx: add motion events
iio: imu: st_lsm6dsx: move interrupt thread to core
iio: imu: inv_mpu6050: add fifo support for magnetometer data
...
Remove a stray newline from the probe callback.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Change to use devm_hwspin_lock_request_specific() to help to simplify the
cleanup code for drivers requesting one hwlock.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The iio_triggered_buffer_{predisable,postenable} functions attach/detach
the poll functions.
The iio_triggered_buffer_predisable() should be called last, to detach the
poll func after the devices has been suspended.
The position of iio_triggered_buffer_postenable() is correct.
Note this is not stable material. It's a fix in the logical
model rather fixing an actual bug. These are being tidied up
throughout the subsystem to allow more substantial rework that
was blocked by variations in how things were done.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The measured time value in the driver is limited to the maximum distance
which can be read by the sensor. This limitation was wrong and is fixed
by this patch.
It also takes into account that we are supporting a variety of sensors
today and that the recently added sensors have a higher maximum
distance range.
Changes in v2:
- Added a Tested-by
Suggested-by: Zbyněk Kocur <zbynek.kocur@fel.cvut.cz>
Tested-by: Zbyněk Kocur <zbynek.kocur@fel.cvut.cz>
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Cc:<Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It could happen that either `val` or `val2` [provided from userspace] is
negative. In that case the computed frequency could get a weird value.
Fix this by checking that neither of the 2 variables is negative, and check
that the computed result is not-zero.
Fixes: e4f9593901 ("iio: imu: adis16480 switch sampling frequency attr to core support")
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
* adis16400
- Make sure to free memory on a few failure paths.
* adxl372
- Fix wrong fifo depth
- Fix wrong indexing of data from the fifo.
- Perform a reset at startup to avoid a problem with inconsistent state.
* axp288
- This is a fix for a fix. The original fix made sure we kept the
configuration from some firmwares to preserve a bias current.
Unfortunately it appears the previous behaviour was working around
a buggy firmware by overwriting the wrong value it had. Hence
a regression was seen.
* bmc150
- Fix the centre temperature. This was due to an error in one of the
datasheets.
* hx711
- Fix an issue where a badly timed interrupt could lead to a control
line being high long enough to put the device into a low power state.
* meson_sar_adc
- Fix a case where the irq was enabled before everything it uses was
allocated.
* st_lsm6dsx
- Ensure we don't set the sensor sensitivity to 0 as it will force
all readings to 0.
- Fix a wait time for the slave i2c controller when the accelerometer
is not enabled.
* stm32-adc
- Precursor for fix. Move a set of register definitions to a header.
- Fix a race when several ADCs are in use with some using interrupts
to control the dataflow and some using DMA.
* vcnl4000
- Fix a garbage of_match_table in which a string was passed instead
of the intended enum.
-----BEGIN PGP SIGNATURE-----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=s9EA
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-5.4a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes for the 5.4 cycle.
* adis16400
- Make sure to free memory on a few failure paths.
* adxl372
- Fix wrong fifo depth
- Fix wrong indexing of data from the fifo.
- Perform a reset at startup to avoid a problem with inconsistent state.
* axp288
- This is a fix for a fix. The original fix made sure we kept the
configuration from some firmwares to preserve a bias current.
Unfortunately it appears the previous behaviour was working around
a buggy firmware by overwriting the wrong value it had. Hence
a regression was seen.
* bmc150
- Fix the centre temperature. This was due to an error in one of the
datasheets.
* hx711
- Fix an issue where a badly timed interrupt could lead to a control
line being high long enough to put the device into a low power state.
* meson_sar_adc
- Fix a case where the irq was enabled before everything it uses was
allocated.
* st_lsm6dsx
- Ensure we don't set the sensor sensitivity to 0 as it will force
all readings to 0.
- Fix a wait time for the slave i2c controller when the accelerometer
is not enabled.
* stm32-adc
- Precursor for fix. Move a set of register definitions to a header.
- Fix a race when several ADCs are in use with some using interrupts
to control the dataflow and some using DMA.
* vcnl4000
- Fix a garbage of_match_table in which a string was passed instead
of the intended enum.
* tag 'iio-fixes-for-5.4a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio: Fix an undefied reference error in noa1305_probe
iio: light: opt3001: fix mutex unlock race
iio: adc: ad799x: fix probe error handling
iio: light: add missing vcnl4040 of_compatible
iio: light: fix vcnl4000 devicetree hooks
iio: imu: st_lsm6dsx: fix waitime for st_lsm6dsx i2c controller
iio: adc: axp288: Override TS pin bias current for some models
iio: imu: adis16400: fix memory leak
iio: imu: adis16400: release allocated memory on failure
iio: adc: stm32-adc: fix a race when using several adcs with dma and irq
iio: adc: stm32-adc: move registers definitions
iio: accel: adxl372: Perform a reset at start up
iio: accel: adxl372: Fix push to buffers lost samples
iio: accel: adxl372: Fix/remove limitation for FIFO samples
iio: adc: hx711: fix bug in sampling of data
iio: fix center temperature of bmc150-accel-core
iio: imu: st_lsm6dsx: forbid 0 sensor sensitivity
iio: adc: meson_saradc: Fix memory allocation order
I hit the following error when compile the kernel.
drivers/iio/light/noa1305.o: In function `noa1305_probe':
noa1305.c:(.text+0x65): undefined reference to `__devm_regmap_init_i2c'
make: *** [vmlinux] Error 1
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When an end-of-conversion interrupt is received after performing a
single-shot reading of the light sensor, the driver was waking up the
result ready queue before checking opt->ok_to_ignore_lock to determine
if it should unlock the mutex. The problem occurred in the case where
the other thread woke up and changed the value of opt->ok_to_ignore_lock
to false prior to the interrupt thread performing its read of the
variable. In this case, the mutex would be unlocked twice.
Signed-off-by: David Frey <dpfrey@gmail.com>
Reviewed-by: Andreas Dannenberg <dannenberg@ti.com>
Fixes: 94a9b7b180 ("iio: light: add support for TI's opt3001 light sensor")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since commit 0f7ddcc1bf ("iio:adc:ad799x: Write default config on probe
and reset alert status on probe") the error path is wrong since it
leaves the vref regulator on. Fix this by disabling both regulators.
Fixes: 0f7ddcc1bf ("iio:adc:ad799x: Write default config on probe and reset alert status on probe")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Commit 5a441aade5 ("iio: light: vcnl4000 add support for the VCNL4040
proximity and light sensor") added the support for the vcnl4040 but
forgot to add the of_compatible. Fix this by adding it now.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Fixes: 5a441aade5 ("iio: light: vcnl4000 add support for the VCNL4040 proximity and light sensor")
Reviewed-by: Angus Ainslie (Purism) angus@akkea.ca
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since commit ebd457d559 ("iio: light: vcnl4000 add devicetree hooks")
the of_match_table is supported but the data shouldn't be a string.
Instead it shall be one of 'enum vcnl4000_device_ids'. Also the matching
logic for the vcnl4020 was wrong. Since the data retrieve mechanism is
still based on the i2c_device_id no failures did appeared till now.
Fixes: ebd457d559 ("iio: light: vcnl4000 add devicetree hooks")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Angus Ainslie (Purism) angus@akkea.ca
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
i2c controller available in st_lsm6dsx series performs i2c slave
configuration using accel clock as trigger.
st_lsm6dsx_shub_wait_complete routine is used to wait the controller has
carried out the requested configuration. However if the accel sensor is not
enabled we should not use its configured odr to estimate a proper timeout
Fixes: c91c1c844e ("iio: imu: st_lsm6dsx: add i2c embedded controller support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since commit 9bcf15f75c ("iio: adc: axp288: Fix TS-pin handling") we
preserve the bias current set by the firmware at boot. This fixes issues
we were seeing on various models, but it seems our old hardcoded 80ųA bias
current was working around a firmware bug on at least one model laptop.
In order to both have our cake and eat it, this commit adds a dmi based
list of models where we need to override the firmware set bias current and
adds the one model we now know needs this to it: The Lenovo Ideapad 100S
(11 inch version).
Fixes: 9bcf15f75c ("iio: adc: axp288: Fix TS-pin handling")
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=203829
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In adis_update_scan_mode_burst, if adis->buffer allocation fails release
the adis->xfer.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In adis_update_scan_mode, if allocation for adis->buffer fails,
previously allocated adis->xfer needs to be released.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
End of conversion may be handled by using IRQ or DMA. There may be a
race when two conversions complete at the same time on several ADCs.
EOC can be read as 'set' for several ADCs, with:
- an ADC configured to use IRQs. EOCIE bit is set. The handler is normally
called in this case.
- an ADC configured to use DMA. EOCIE bit isn't set. EOC triggers the DMA
request instead. It's then automatically cleared by DMA read. But the
handler gets called due to status bit is temporarily set (IRQ triggered
by the other ADC).
So both EOC status bit in CSR and EOCIE control bit must be checked
before invoking the interrupt handler (e.g. call ISR only for
IRQ-enabled ADCs).
Fixes: 2763ea0585 ("iio: adc: stm32: add optional dma support")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move STM32 ADC registers definitions to common header.
This is precursor patch to:
- iio: adc: stm32-adc: fix a race when using several adcs with dma and irq
It keeps registers definitions as a whole block, to ease readability and
allow simple access path to EOC bits (readl) in stm32-adc-core driver.
Fixes: 2763ea0585 ("iio: adc: stm32: add optional dma support")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
We need to perform a reset a start up to make sure that the chip is in a
consistent state. This reset also disables all the interrupts which
should only be enabled together with the iio buffer. Not doing this, was
sometimes causing unwanted interrupts to trigger.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Fixes: f4f55ce38e ("iio:adxl372: Add FIFO and interrupts support")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
One in two sample sets was lost by multiplying fifo_set_size with
sizeof(u16). Also, the double number of available samples were pushed to
the iio buffers.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Fixes: f4f55ce38e ("iio:adxl372: Add FIFO and interrupts support")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Currently, the driver sets the FIFO_SAMPLES register with the number of
sample sets (maximum of 170 for 3 axis data, 256 for 2-axis and 512 for
single axis). However, the FIFO_SAMPLES register should store the number
of samples, regardless of how the FIFO format is configured.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Fixes: f4f55ce38e ("iio:adxl372: Add FIFO and interrupts support")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix bug in sampling function hx711_cycle() when interrupt occures while
PD_SCK is high. If PD_SCK is high for at least 60 us power down mode of
the sensor is entered which in turn leads to a wrong measurement.
Switch off interrupts during a PD_SCK high period and move query of DOUT
to the latest point of time which is at the end of PD_SCK low period.
This bug exists in the driver since it's initial addition. The more
interrupts on the system the higher is the probability that it happens.
Fixes: c3b2fdd0ea ("iio: adc: hx711: Add IIO driver for AVIA HX711")
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There is a return statement that is indented incorrectly, add in
the missing tab.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The iio_triggered_buffer_predisable() should be called last, to detach the
poll func after the devices has been suspended.
This change re-organizes things a bit so that the postenable & predisable
are symmetrical. It also converts the preenable() to a postenable().
Not stable material as there is no known problem with the current
code, it's just not consistent with the form we would like all the
IIO drivers to adopt so as to allow subsystem wide changes.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
If a label is defined in the device tree for this device add that
to the device specific attributes. This is useful for userspace to
be able to identify an individual device when multiple identical
chips are present in the system.
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The lock is used to protect the buffer during reads. Though the spi
routines have their own locks, it may be the case that the buffer needs to
be protected before it's stored and passed to the IIO read hooks.
indio_dev's mlock was used before.
This change replaces it with the driver's own lock.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The use of indio_dev's mlock is discouraged. The driver already defines
it's own `bus_lock` in `adis16130_spi_read()`, so using the mlock is
redundant.
The parts supported by this chip are obsoleted anyway, so for now we just
remove mlock as part of a general cleanup, until the driver gets removed.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Report iio motion events to iio subsystem and filter motion events.
Wakeup will still be on all channels as it's not possible to do the filtering
in hw.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Reviewed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The interrupt source can come from multiple sources,
fifo and wake interrupts.
Enter interrupt thread to check which interrupt that has fired.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Reviewed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This add ways for the SoC to wake from accelerometer wake events.
In the suspend function we skip disabling the sensor if wakeup-source
and events are activated.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Reviewed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add event channels that controls the creation of motion events.
Tested on ISM330DLC
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Reviewed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This prepares the interrupt to be used for other stuff than
fifo reading + event readings.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Put read magnetometer data by mpu inside the fifo.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support of driving MPU9250 magnetometer connected on i2c
auxiliary bus using the MPU i2c master.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add helper functions to use the i2c auxiliary bus with the MPU i2c
master block.
Support only register based chip, reading and 1 byte writing. These
will be useful for initializing magnetometers inside MPU9x50 chips.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use the correct syntax *-y for declaring object files.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Disable i2c mux for supported 9xxx chips. This is a
pre-requesite for controling 9xxx magnetometer using the
i2c master of the chip.
Check in device-tree that there is no i2c-gate device declared
for ensuring backward compatibility with existing setups.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This driver supports 14-bits and 16-bits devices. All of them have a 14-bit
configuration registers. All SPI trasfers, for reading AD conversion
results and for writing the configuration register, fit in two bytes.
The driver always uses 4-bytes xfers which seems at least pointless (maybe
even harmful). This patch trims the SPI xfer len and the buffer size to
two bytes.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The iio_triggered_buffer_{predisable,postenable} functions attach/detach
the poll functions.
For the predisable hook, the disable code should occur before detaching
the poll func, and for the postenable hook, the poll func should be
attached before the enable code.
The driver was slightly reworked. The preenable hook was moved to the
postenable, to add some symmetry to the postenable/predisable part.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Here is the big staging/iio driver update for 5.4-rc1.
Lots of churn here, with a few driver/filesystems moving out of staging
finally:
- erofs moved out of staging
- greybus core code moved out of staging
Along with that, a new filesytem has been added:
- extfat
to provide support for those devices requiring that filesystem (i.e.
transfer devices to/from windows systems or printers.)
Other than that, there a number of new IIO drivers, and lots and lots
and lots of staging driver cleanups and minor fixes as people continue
to dig into those for easy changes.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXYIW0g8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynJgwCgt22YQdsWRrOuJnZp3xpFq/ZSMWAAn0dAgFf5
SlSTI2nQhbW7jjdShrPR
=Ra09
-----END PGP SIGNATURE-----
Merge tag 'staging-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging and IIO driver updates from Greg KH:
"Here is the big staging/iio driver update for 5.4-rc1.
Lots of churn here, with a few driver/filesystems moving out of
staging finally:
- erofs moved out of staging
- greybus core code moved out of staging
Along with that, a new filesytem has been added:
- extfat
to provide support for those devices requiring that filesystem (i.e.
transfer devices to/from windows systems or printers)
Other than that, there a number of new IIO drivers, and lots and lots
and lots of staging driver cleanups and minor fixes as people continue
to dig into those for easy changes.
All of these have been in linux-next for a while with no reported
issues"
* tag 'staging-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (453 commits)
Staging: gasket: Use temporaries to reduce line length.
Staging: octeon: Avoid several usecases of strcpy
staging: vhciq_core: replace snprintf with scnprintf
staging: wilc1000: avoid twice IRQ handler execution for each single interrupt
staging: wilc1000: remove unused interrupt status handling code
staging: fbtft: make several arrays static const, makes object smaller
staging: rtl8188eu: make two arrays static const, makes object smaller
staging: rtl8723bs: core: Remove Macro "IS_MAC_ADDRESS_BROADCAST"
dt-bindings: anybus-controller: move to staging/ tree
staging: emxx_udc: remove local TRUE/FALSE definition
staging: wilc1000: look for rtc_clk clock
staging: dt-bindings: wilc1000: add optional rtc_clk property
staging: nvec: make use of devm_platform_ioremap_resource
staging: exfat: drop unused function parameter
Staging: exfat: Avoid use of strcpy
staging: exfat: use integer constants
staging: exfat: cleanup spacing for casts
staging: exfat: cleanup spacing for operators
staging: rtl8723bs: hal: remove redundant variable n
staging: pi433: Fix typo in documentation
...
RST conversion is happily mostly behind us.
- A new document on reproducible builds.
- We finally got around to zapping the documentation for hardware support
that was removed in 2004; one doesn't want to rush these things.
- The usual assortment of fixes, typo corrections, etc.
You'll still find a handful of annoying conflicts against other trees,
mostly tied to the last RST conversions; resolutions are straightforward
and the linux-next ones are good.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAl1/J4IACgkQF0NaE2wM
flhYogf9EgYozCe8RocSq+JjJpZOSFjIGDQv+GwTjOBIdqgO9tSIaY/p0wSkYKil
jYXyMDF+Xwr8podsUep2F7akBM7j9XJ+XBGJcfOna0ypC9xoejMgWt9fU3YvaWge
dQJxIQ/iwkDlKNx6uOYgKysLUWFS0EP/nzPhqBo4bZZzhugvrR46D/nQqFNmGihd
l9yLalJtP5mC0XRUv3hpdAFFFKxdC0R3BGOel2V+slSClp0LEgpdMAuMaKydEDI3
Ch9ZpIp8fB8kqONCs9/X6083WRsDOMe28KgeGrGHo4Jla6u51QBLQjSVKttFv7xk
051yNJwDWMxgl+A4gyNLDPXM7Gd7HQ==
=v4dp
-----END PGP SIGNATURE-----
Merge tag 'docs-5.4' of git://git.lwn.net/linux
Pull documentation updates from Jonathan Corbet:
"It's a somewhat calmer cycle for docs this time, as the churn of the
mass RST conversion is happily mostly behind us.
- A new document on reproducible builds.
- We finally got around to zapping the documentation for hardware
support that was removed in 2004; one doesn't want to rush these
things.
- The usual assortment of fixes, typo corrections, etc"
* tag 'docs-5.4' of git://git.lwn.net/linux: (67 commits)
Documentation: kbuild: Add document about reproducible builds
docs: printk-formats: Stop encouraging use of unnecessary %h[xudi] and %hh[xudi]
Documentation: Add "earlycon=sbi" to the admin guide
doc🔒 remove reference to clever use of read-write lock
devices.txt: improve entry for comedi (char major 98)
docs: mtd: Update spi nor reference driver
doc: arm64: fix grammar dtb placed in no attributes region
Documentation: sysrq: don't recommend 'S' 'U' before 'B'
mailmap: Update email address for Quentin Perret
docs: ftrace: clarify when tracing is disabled by the trace file
docs: process: fix broken link
Documentation/arm/samsung-s3c24xx: Remove stray U+FEFF character to fix title
Documentation/arm/sa1100/assabet: Fix 'make assabet_defconfig' command
Documentation/arm/sa1100: Remove some obsolete documentation
docs/zh_CN: update Chinese howto.rst for latexdocs making
Documentation: virt: Fix broken reference to virt tree's index
docs: Fix typo on pull requests guide
kernel-doc: Allow anonymous enum
Documentation: sphinx: Don't parse socket() as identifier reference
Documentation: sphinx: Add missing comma to list of strings
...
Adding missing indio_dev->dev.of_node references so that, in case multiple
max31856 are present, users can get some clues to being able to distinguish
each of them. While at it, add also the missing parent reference.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Enable clear on read feature for latched interrupts. This bit allows
immediately clearing the latched interrupts of an event detection upon
the read of the corresponding status register.
It must be set to 1 together with LIR.
This feature is available just on LSM6DS0/LSM6DSR/ASM330LHH
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Enable Latched interrupt by default for sensor events
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The device could be configured to spit out also the configuration word
while reading the AD result value (in the same SPI xfer) - this is called
"readback" in the device datasheet.
The driver checks if readback is enabled and it eventually adjusts the SPI
xfer length and it applies proper shifts to still get the data, discarding
the configuration word.
The readback option is actually never enabled (the driver disables it), so
the said checks do not serve for any purpose.
Since enabling the readback option seems not to provide any advantage (the
driver entirely sets the configuration word without relying on any default
value), just kill the said, unused, code.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Separate the declaration of struct bh1750_chip_info from definition
of bh1750_chip_info_tbl[] in a single statement as it makes the code
hard to read, and with the extra newline it makes it look as if the
bh1750_chip_info_tbl[] had no explicit type.
This change also resolves the following compiler warning about the
unusual position of the static keyword that can be seen when building
with warnings enabled (W=1):
drivers/iio/light/bh1750.c:64:1: warning:
‘static’ is not at beginning of declaration [-Wold-style-declaration]
Related to commit 3a11fbb037 ("iio: light: add support for ROHM
BH1710/BH1715/BH1721/BH1750/BH1751 ambient light sensors").
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for the ADC hardware present on Ingenic JZ4770 SoC.
Signed-off-by: Artur Rojek <contact@artur-rojek.eu>
Tested-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The center temperature of the supported devices stored in the constant
BMC150_ACCEL_TEMP_CENTER_VAL is not 24 degrees but 23 degrees.
It seems that some datasheets were inconsistent on this value leading
to the error. For most usecases will only make minor difference so
not queued for stable.
Signed-off-by: Pascal Bouwmann <bouwmann@tau-tec.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Variable ret is being assigned a value that is never read and
is being re-assigned a little later on. The assignment is redundant
and hence can be removed.
Addresses-Coverity: ("Ununsed value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Do not allow configuring null sensor gain since it will force to 0
device outputs
Fixes: c8d4066c7246 ("iio: imu: st_lsm6dsx: remove invalid gain value for LSM9DS1")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
meson_saradc's irq handler uses priv->regmap so make sure that it is
allocated before the irq get enabled.
This also fixes crash when CONFIG_DEBUG_SHIRQ is enabled, as device
managed resources are freed in the inverted order they had been
allocated, priv->regmap was freed before the spurious fake irq that
CONFIG_DEBUG_SHIRQ adds called the handler.
Fixes: 3af109131b ("iio: adc: meson-saradc: switch from polling to interrupt mode")
Reported-by: Elie Roudninski <xademax@gmail.com>
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Elie ROUDNINSKI <xademax@gmail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch exports the ad_sd_calibrate function in order to be able to
call it from outside ad_sigma_delta.
There are cases where the option to calibrate one channel at a time is
necessary (ex. system calibration for zero scale and full scale).
Signed-off-by: Mircea Caprioru <mircea.caprioru@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The commit 473d12f763
("iio: hid-sensor-attributes: Convert to use int_pow()")
converted to use generic int_pow() helper. Though, the generic one returns
64-bit value and, in cases when it is used as divisor, it compels 64-bit
division from compiler.
In order to fix this, introduce a temporary 32-bit variable to hold the result
of int_pow() and use it as divisor afterwards.
In couple of cases, replace int_pow() with a predefined unit factors for time
and frequency.
Fixes: 473d12f763 ("iio: hid-sensor-attributes: Convert to use int_pow()")
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20190905112759.13035-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Revised pull request to fix up a missing Signed-off-by and roll in
a fix in the lsm9ds1 support after I broke it when applying.
Revised again because the fix changed a hash meaning a fix
that previously followed it now had the wrong fixes tag.
A few fixes in here that could have gone a faster path but aren't quite
worth the rush for 5.3.
New device support
* ad7606
- Support the ad7606b which adds a software controlled mode alongside
the pin controlled only approach of the ad7606. Including dt-bindings.
* lsm6dsx
- Add support for the gyro and accelerometer part of the lsm9ds1 which is
a compound device also including a magnetometer (st_sensors driver).
Includes bindings and precursor rework of the driver.
Features
* ad7192
- Add support for low pass filter control.
- DT binding docs.
Cleanups and minor fixes
* MAINTAINERS
- Fix a typo in a path.
- Add entry for ad7606
* ad5380
- Fix a failure to dereference a pointer before atempting to assign the
value.
* ad7192
- Drop platform data as not used in mainline and we now have full DT bindings.
* ad7606
- YAML conversion for dt-bindings.
* adis16240
- Rework write_raw to make it more readable using GENMASK.
* adis16460
- Fix and issue with an unsigned variable holding potential negatives.
* cros_ec
- Fix missing default of calibration vector so that we get 'something'
before calibration is complete on a given axis.
* hid-sensors
- Use int_pow instead of opencoding.
* isl29501
- rename dt-binding docs to include renesas inline with other renesas parts
and general current convention.
* kxcjk1013
- Improve comments on the 'unusual' ACPI ids used to identify which sensor
is which in certain laptops.
* lsm6dsx
- Add one bit to the fifo status masks for a number of parts.
- Drop a reserved entry from the sensitivity values to tidy up interface.
- Use core conversion macro from G to m/s^2 for lsm9ds1 to make it easier
to relate to the datasheet and consistent with other parts supported.
* max1027
- Use device managed APIs to avoid manual error handling and cleanup.
* rfd77402
- Typo in Kconfig help.
* sc27xx
- Switch to polling mode from interrupts as interrupt handling typically
to slow for very short sleeps.
* st-sensors
- Fix some missing selects for regmap.
* tools
- Add a .gitignore containing the binary outputs.
-----BEGIN PGP SIGNATURE-----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=rPVR
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.4b-take3' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of new device support, cleanups and features for IIO in the 5.4 cycle
Revised pull request to fix up a missing Signed-off-by and roll in
a fix in the lsm9ds1 support after I broke it when applying.
Revised again because the fix changed a hash meaning a fix
that previously followed it now had the wrong fixes tag.
A few fixes in here that could have gone a faster path but aren't quite
worth the rush for 5.3.
New device support
* ad7606
- Support the ad7606b which adds a software controlled mode alongside
the pin controlled only approach of the ad7606. Including dt-bindings.
* lsm6dsx
- Add support for the gyro and accelerometer part of the lsm9ds1 which is
a compound device also including a magnetometer (st_sensors driver).
Includes bindings and precursor rework of the driver.
Features
* ad7192
- Add support for low pass filter control.
- DT binding docs.
Cleanups and minor fixes
* MAINTAINERS
- Fix a typo in a path.
- Add entry for ad7606
* ad5380
- Fix a failure to dereference a pointer before atempting to assign the
value.
* ad7192
- Drop platform data as not used in mainline and we now have full DT bindings.
* ad7606
- YAML conversion for dt-bindings.
* adis16240
- Rework write_raw to make it more readable using GENMASK.
* adis16460
- Fix and issue with an unsigned variable holding potential negatives.
* cros_ec
- Fix missing default of calibration vector so that we get 'something'
before calibration is complete on a given axis.
* hid-sensors
- Use int_pow instead of opencoding.
* isl29501
- rename dt-binding docs to include renesas inline with other renesas parts
and general current convention.
* kxcjk1013
- Improve comments on the 'unusual' ACPI ids used to identify which sensor
is which in certain laptops.
* lsm6dsx
- Add one bit to the fifo status masks for a number of parts.
- Drop a reserved entry from the sensitivity values to tidy up interface.
- Use core conversion macro from G to m/s^2 for lsm9ds1 to make it easier
to relate to the datasheet and consistent with other parts supported.
* max1027
- Use device managed APIs to avoid manual error handling and cleanup.
* rfd77402
- Typo in Kconfig help.
* sc27xx
- Switch to polling mode from interrupts as interrupt handling typically
to slow for very short sleeps.
* st-sensors
- Fix some missing selects for regmap.
* tools
- Add a .gitignore containing the binary outputs.
* tag 'iio-for-5.4b-take3' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (27 commits)
iio: imu: st_lsm6dsx: rely on IIO_G_TO_M_S_2 for gain definition for LSM9DS1
iio: imu: st_lsm6dsx: remove invalid gain value for LSM9DS1
iio: cros_ec: set calibscale for 3d MEMS to unit vector
iio: dac: ad5380: fix incorrect assignment to val
iio: imu: st_lsm6dsx: Fix FIFO diff mask for tagged fifo
dt-bindings: iio: imu: st_lsm6dsx: add lsm9ds1 device bindings
iio: imu: st_lsm6dsx: add support for accel/gyro unit of lsm9ds1
iio: imu: st_lsm6dsx: move register definitions to sensor_settings struct
iio: imu: st_lsm6dsx: introduce update_fifo function pointer
dt-bindings: iio: light: isl29501: Rename bindings documentation file
Kconfig: Fix the reference to the RFD77402 ToF sensor in the 'help' section
iio: st_sensors: Fix build error
dt-bindings: iio: adc: Add AD7606B ADC documentation
dt-bindings: iio: adc: Migrate AD7606 documentation to yaml
MAINTAINERS: Add Beniamin Bia for AD7606 driver
iio: adc: ad7606: Add support for AD7606B ADC
tools: iio: add .gitignore
iio: adc: sc27xx: Change to polling mode to read data
iio: hid-sensor-attributes: Convert to use int_pow()
iio: adc: max1027: Use device-managed APIs
...
Rely on IIO_G_TO_M_S_2 macro for LSM9DS1 accelerometer gain definitions
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Get rid of invalid sensitivity value for LSM9DS1 gyro sensor
Fixes: 52f4b1f196 ("iio: imu: st_lsm6dsx: add support for accel/gyro unit of lsm9ds1")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
A driver for ADS1015 with more functionality is available in the iio
subsystem.
Remove the hwmon driver as duplicate. If the chip is used for hardware
monitoring, the iio->hwmon bridge should be used.
Cc: Dirk Eibach <eibach@gdsys.de>
Link: https://lore.kernel.org/r/1562004758-13025-1-git-send-email-linux@roeck-us.net
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
By default, set the calibscale vector to unit vector.
When calibrating one axis, the other axis calibrations are sent as well.
If left to 0, sensor data from uncalibrated axis are zero'ed out until
all axis are calibrated.
Fixes: ed1f2e85da ("iio: cros_ec: Add calibscale for 3d MEMS ")
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Currently the pointer val is being incorrectly incremented
instead of the value pointed to by val. Fix this by adding
in the missing * indirection operator.
Addresses-Coverity: ("Unused value")
Fixes: c03f2c5368 ("staging:iio:dac: Add AD5380 driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
According to the latest version of datasheet the mask
for number of unread sensor data in FIFO_STATUS registers
has been extended to 10 bits
The devices involved are:
- LSM6DSO
- LSM6DSOX
- ASM330LHH
- LSM6DSR
- ISM330DHCX
Signed-off-by: mario tesi <mario.tesi@st.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The LSM9DS1's accelerometer / gyroscope unit and it's magnetometer (separately
supported in iio/magnetometer/st_magn*) are located on a separate i2c addresses
on the bus.
For the datasheet, see https://www.st.com/resource/en/datasheet/lsm9ds1.pdf
Treat it just like the LSM6* devices and, despite it's name, hook it up
to the st_lsm6dsx driver, using it's basic functionality.
accelerometer and gyroscope are not independently clocked. It runs at the gyro
frequencies if both are enabled, see chapter 7.12 of the datasheet.
We could have handled this as a single IIO device but we have split
it up to be more consistent with the other more flexible devices.
Despite supporting and testing the LSM9DS1, we call the gyro channels
iio_chan_spec struct "st_lsm6ds0_gyro_channels" because the register
description is equal. This suggests that supporting LSM6DS0 should be
trivial to do.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There is a bit of mess between cros-ec mfd includes and platform
includes. For example, we have a linux/mfd/cros_ec.h include that
exports the interface implemented in platform/chrome/cros_ec_proto.c. Or
we have a linux/mfd/cros_ec_commands.h file that is non related to the
multifunction device (in the sense that is not exporting any function of
the mfd device). This causes crossed includes between mfd and
platform/chrome subsystems and makes the code difficult to read, apart
from creating 'curious' situations where a platform/chrome driver includes
a linux/mfd/cros_ec.h file just to get the exported functions that are
implemented in another platform/chrome driver.
In order to have a better separation on what the cros-ec multifunction
driver does and what the cros-ec core provides move and rework the
affected includes doing:
- Move cros_ec_commands.h to include/linux/platform_data/cros_ec_commands.h
- Get rid of the parts that are implemented in the platform/chrome/cros_ec_proto.c
driver from include/linux/mfd/cros_ec.h to a new file
include/linux/platform_data/cros_ec_proto.h
- Update all the drivers with the new includes, so
- Drivers that only need to know about the protocol include
- linux/platform_data/cros_ec_proto.h
- linux/platform_data/cros_ec_commands.h
- Drivers that need to know about the cros-ec mfd device also include
- linux/mfd/cros_ec.h
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: Gwendal Grignou <gwendal@chromium.org>
Series changes: 3
- Fix dereferencing pointer to incomplete type 'struct cros_ec_dev' (lkp)
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Now, the ChromeOS EC core driver has nothing related to an MFD device, so
move that driver from the MFD subsystem to the platform/chrome subsystem.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Move some register definitions to the per-device array of struct
st_lsm6dsx_sensor_settings in order to simplify adding new sensor
devices to the driver.
Also, remove completely unused register definitions.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Introduce update_fifo routine pointer in st_lsm6dsx_fifo_ops data
structure since we will need a different update FIFO configuration
callback adding support for lsm6ds0/lsm9ds1 imu device
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Tested-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This should be RFD77402, not RFD77420.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
IIO_ST_SENSORS_CORE select IIO_ST_SENSORS_I2C
unconditionally, if REGMAP_I2C is not set, build fails
drivers/iio/common/st_sensors/st_sensors_i2c.o: In function `st_sensors_i2c_configure':
st_sensors_i2c.c:(.text+0x58): undefined reference to `__devm_regmap_init_i2c'
This patch selects REGMAP_I2C to fix it.
IIO_ST_SENSORS_SPI is similar to SPI issue.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 062809ef77 ("iio: make st_sensors drivers use regmap")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The AD7606B is a 16-bit ADC that supports simultaneous sampling of 8
channels. It is pin compatible to AD7606, but adds extra modes by
writing to the register map.
The AD7606B can be configured to work in software mode by setting all
oversampling pins to high. This mode is selected by default.
The oversampling ratio is configured from the OS_MODE register (address
0x08) with the addition of OS=128 and OS=256 that were not available in
hardware mode.
The device is configured to output data on a single spi channel, but this
configuration must be done right after restart. That is why the delay was
removed for devices which doesn't require it.
Moreover, in software mode, the range gpio has no longer its function.
Instead, the scale can be configured individually for each channel from
the RANGE_CH registers (address 0x03 to 0x06). Besides the already
supported ±10 V and ±5 V ranges, software mode can also accommodate the
±2.5 V range.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Co-developed-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
On Spreadtrum platform, the headphone will read one ADC channel multiple
times to identify the headphone type, and the headphone identification is
sensitive of the ADC reading time. And we found it will take longer time
to reading ADC data by using interrupt mode comparing with the polling
mode, thus we should change to polling mode to improve the efficiency
of reading data, which can identify the headphone type successfully.
Signed-off-by: Freeman Liu <freeman.liu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Instead of linear approach to calculate power of 10, use generic int_pow()
which does it better.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use device-managed APIs to simplify the code.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Caught via static-analysis checker:
```
drivers/iio/imu/adis16460.c
152 static int adis16460_set_freq(struct iio_dev *indio_dev, int val, int val2)
153 {
154 struct adis16460 *st = iio_priv(indio_dev);
155 unsigned int t;
^^^^^^^^^^^^^^
156
157 t = val * 1000 + val2 / 1000;
158 if (t <= 0)
^^^^^^
Unsigned is not less than zero.
```
The types of `val` && `val2` are obtained from the IIO `write_raw` hook, so
userspace can provide negative values, which can cause weird behavior after
conversion to unsigned.
This patch changes the sign of variable `t` so that -EINVAL will be
returned for negative values as well.
Fixes: db6ed4d23d ("iio: imu: Add support for the ADIS16460 IMU")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The KIOX010A and KIOX020A ACPI ids go hand in hand, they are used in
yoga style 2-in-1s, with KIOX010A indicating the KXCJ91008 sensor in the
display of the 2-in-1 and KIOX020A indicating the KXCJ91008 sensor in the
base.
Improve the existing comment on the "KIOX010A" kx_acpi_match table entry
to make clear we are talking about a yoga-style (360 degree hinges) device
here and add a similar comment to the "KIOX020A" entry.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This got caught by the implicit fall through detection but is
a bug rather than missing marking.
Reported-by: 0-DAY kernel test infrastructure
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fixes: 741172d18e ("iio: light: noa1305: Add support for NOA1305")
Link: https://lore.kernel.org/r/20190813133851.14345-1-Jonathan.Cameron@huawei.com
Cc: Gustavo Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Note includes a merge from i3c tree to get support needed for stm_lsm6dsx driver
support for l3c devices. Done from immutable branch.
A counter subsystem patche in here as well.
Alongside the new device support (which is always good), Chuhong's work
on using devres managed APIs has cleaned up a number of drivers.
New device support
* adis16460
- New driver based on ADIS framework which needed addition of support
for cs_change_delay. Includes device tree binding.
* cros_ec
- Support fo the veyron-minnie which uses an older interface.
* lsm6dsx
- Support for LSM6DSTR-C gyro + magnetometer sensor (new IDs mainly)
- Support for ISM330DHCX acc + gyro sensor (extensive rework needed!)
* Maxim 5432
- New driver support MAX5432-MAX5435 family of potentiometers.
* noa1305
- New driver for this ON Semiconductor Ambient light sensor.
Features and cleanups
* tree wide
- Drop error prints after platform_get_irq as already prints errors
internally if any occur.
* docs
- Document mounting matrix.
- Fix a missing newline at end of file.
* ad2s1210
- Switch to device managed APIs for all of probe and drop explicit remove.
* ad7192
- Add of_device_id array to explicity handling DT bindings.
* ad7606
- Lots of rework leading to support for software configure modes in ad7616
parts.
- Debugfs register access support.
* am2315
- Switch to device managed APIs for all of probe and drop explicit remove.
* apds9960
- Typo in module description.
* cm36651
- Convert to i2c_new_dummy_device.
- Swithc to device managed APIs for all of probe adn drop explicit remove.
* cros_ec
- Calibscale support for accel, gyro and magnetometer.
- Tidy up some error codes to return the error from the stack rather than
-EIO.
- Determine protocol version.
- Add a sign vector to the core to fix sensor rotation if necessary.
Cannot just be done with mount matrix as already in use in many devices.
- Tidy up INFO_SCALE being in both the separate and shared lists.
- Drop a lot of dplicate code from the cros-ec-accel-legacy driver
and use the core provided code instead.
- Make frequency range available to userspace.
* counter / ftm-quaddec
- Switch to device managed APIs for all of probe adn drop explicit remove.
* hdc100x
- Switch to device managed APIs for all of probe and drop explicit remove.
* hi8435
- Use gpiod_set_value_cansleep as we don't care here and there is a
board out there where it needs to sleep.
- Switch to device managed APIs for all of probe and drop explict remove.
* hp03
- Convert to i2c_new_dummy_device.
* maxim thermocouple
- Switch to device managed APIs for all of probe and drop explicit remove.
* mmc35240
- Fix typo in constant naming.
* mpu6050
- Use devm_add_action_or_reset in place of explicit error handling.
- Make text in Kconfig more explicit about which parts are supported.
* mxc4005
- Switch to device managed APIs for all of probe and drop explicit remove.
* pms7003
- Convert device tree bindings to yaml.
- Add a MAINTAINERS entry
* sc27xx
- Introduce a local struct device *dev pointer to avoid lots of deref.
- Use devm_add_action_or_reset in place of explicit error handling.
* sca3000
- Typo fix in naming.
* si1145
- Switch to device managed APIs for all of probe and drop explicit remove.
* st_sensors
- Lots of rework to enable switch to regmap.
- Regmap conversion at the end.
- Tidy up some inconsistencies in buffer setup ops.
- Tidy up an oddity by dropping get_irq_data_ready function in favour
of direct access.
- Stop allocating buffer in buffer enable in favour of just embedding
a large enough constant size buffer in the iio_priv accessed structure.
* st_lsm6dsx
- l3c device support (LSM6DSO and LSM6DSR)
- tidy up irq return logic which was strangely written.
- fix up an ABI quirk where this driver used separate scale
attributes, even though they were always shared by type.
* stk33xx
- Device tree bindings include manufacturer ID.
* stm32-adc
- Add control for supply to analog switches including DT bindings.
* stm32 timer
- Drop the quadrature mode support. Believed there were no users so
take this opportunity to drop this unwanted ABI.
* tsl2772
- Switch to device mangage APIs for all of probe and drop explicit remove.
- Use regulator_bulk_* APIs to reduce repitition.
* veml6070
- Convert to i2c_new_dummy_device.
-----BEGIN PGP SIGNATURE-----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=aez5
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.4a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First set of new device support, features and cleanups for IIO in the 5.4 cycle
Note includes a merge from i3c tree to get support needed for stm_lsm6dsx driver
support for l3c devices. Done from immutable branch.
A counter subsystem patche in here as well.
Alongside the new device support (which is always good), Chuhong's work
on using devres managed APIs has cleaned up a number of drivers.
New device support
* adis16460
- New driver based on ADIS framework which needed addition of support
for cs_change_delay. Includes device tree binding.
* cros_ec
- Support fo the veyron-minnie which uses an older interface.
* lsm6dsx
- Support for LSM6DSTR-C gyro + magnetometer sensor (new IDs mainly)
- Support for ISM330DHCX acc + gyro sensor (extensive rework needed!)
* Maxim 5432
- New driver support MAX5432-MAX5435 family of potentiometers.
* noa1305
- New driver for this ON Semiconductor Ambient light sensor.
Features and cleanups
* tree wide
- Drop error prints after platform_get_irq as already prints errors
internally if any occur.
* docs
- Document mounting matrix.
- Fix a missing newline at end of file.
* ad2s1210
- Switch to device managed APIs for all of probe and drop explicit remove.
* ad7192
- Add of_device_id array to explicity handling DT bindings.
* ad7606
- Lots of rework leading to support for software configure modes in ad7616
parts.
- Debugfs register access support.
* am2315
- Switch to device managed APIs for all of probe and drop explicit remove.
* apds9960
- Typo in module description.
* cm36651
- Convert to i2c_new_dummy_device.
- Swithc to device managed APIs for all of probe adn drop explicit remove.
* cros_ec
- Calibscale support for accel, gyro and magnetometer.
- Tidy up some error codes to return the error from the stack rather than
-EIO.
- Determine protocol version.
- Add a sign vector to the core to fix sensor rotation if necessary.
Cannot just be done with mount matrix as already in use in many devices.
- Tidy up INFO_SCALE being in both the separate and shared lists.
- Drop a lot of dplicate code from the cros-ec-accel-legacy driver
and use the core provided code instead.
- Make frequency range available to userspace.
* counter / ftm-quaddec
- Switch to device managed APIs for all of probe adn drop explicit remove.
* hdc100x
- Switch to device managed APIs for all of probe and drop explicit remove.
* hi8435
- Use gpiod_set_value_cansleep as we don't care here and there is a
board out there where it needs to sleep.
- Switch to device managed APIs for all of probe and drop explict remove.
* hp03
- Convert to i2c_new_dummy_device.
* maxim thermocouple
- Switch to device managed APIs for all of probe and drop explicit remove.
* mmc35240
- Fix typo in constant naming.
* mpu6050
- Use devm_add_action_or_reset in place of explicit error handling.
- Make text in Kconfig more explicit about which parts are supported.
* mxc4005
- Switch to device managed APIs for all of probe and drop explicit remove.
* pms7003
- Convert device tree bindings to yaml.
- Add a MAINTAINERS entry
* sc27xx
- Introduce a local struct device *dev pointer to avoid lots of deref.
- Use devm_add_action_or_reset in place of explicit error handling.
* sca3000
- Typo fix in naming.
* si1145
- Switch to device managed APIs for all of probe and drop explicit remove.
* st_sensors
- Lots of rework to enable switch to regmap.
- Regmap conversion at the end.
- Tidy up some inconsistencies in buffer setup ops.
- Tidy up an oddity by dropping get_irq_data_ready function in favour
of direct access.
- Stop allocating buffer in buffer enable in favour of just embedding
a large enough constant size buffer in the iio_priv accessed structure.
* st_lsm6dsx
- l3c device support (LSM6DSO and LSM6DSR)
- tidy up irq return logic which was strangely written.
- fix up an ABI quirk where this driver used separate scale
attributes, even though they were always shared by type.
* stk33xx
- Device tree bindings include manufacturer ID.
* stm32-adc
- Add control for supply to analog switches including DT bindings.
* stm32 timer
- Drop the quadrature mode support. Believed there were no users so
take this opportunity to drop this unwanted ABI.
* tsl2772
- Switch to device mangage APIs for all of probe and drop explicit remove.
- Use regulator_bulk_* APIs to reduce repitition.
* veml6070
- Convert to i2c_new_dummy_device.
* tag 'iio-for-5.4a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (84 commits)
iio: hi8435: Drop hi8435_remove() by using devres for remaining elements
iio: hi8435: Use gpiod_set_value_cansleep()
iio:st_sensors: remove buffer allocation at each buffer enable
iio: imu: inv_mpu6050: be more explicit on supported chips
iio: light: noa1305: Add support for NOA1305
dt-bindings: Add binding document for NOA1305
iio: remove get_irq_data_ready() function pointer and use IRQ number directly
iio: imu: st_lsm6dsx: make IIO_CHAN_INFO_SCALE shared by type
iio: tsl2772: Use regulator_bulk_() APIs
iio: tsl2772: Use devm_iio_device_register
iio: tsl2772: Use devm_add_action_or_reset for tsl2772_chip_off
iio: tsl2772: Use devm_add_action_or_reset
iio: Remove dev_err() usage after platform_get_irq()
iio: light: si1145: Use device-managed APIs
iio:pressure: preenable/postenable/predisable fixup for ST press buffer
iio:magn: preenable/postenable/predisable fixup for ST magn buffer
iio:gyro: preenable/postenable/predisable fixup for ST gyro buffer
iio:accel: preenable/postenable/predisable fixup for ST accel buffer
dt-bindings: iio: imu: st_lsm6dsx: add ism330dhcx device bindings
iio: imu: st_lsm6dsx: add support to ISM330DHCX
...
Convert the remainder of hi8435_probe() to use devres and get rid of
hi8435_remove().
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-iio@vger.kernel.org
Cc: Chris Healy <cphealy@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use gpiod_set_value_cansleep() instead of gpiod_set_value() to support
the case when reset pin is connected to a GPIO expander. See ZII VF610
SCU4 AIB for one such example.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-iio@vger.kernel.org
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch is removing the buffer allocation at each buffer enable.
We just allocate enough memory in the main structure during probe
to cover maximum size needed (that anyway is pretty small) [16bytes].
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The max9611 driver reads the die temperature at probe time to validate
the communication channel. Use the actual read value to perform the test
instead of the read function return value, which was mistakenly used so
far.
The temperature reading test was only successful because the 0 return
value is in the range of supported temperatures.
Fixes: 69780a3bbc ("iio: adc: Add Maxim max9611 ADC driver")
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The fract1 word was not being properly programmed on the device leading
to wrong output frequencies.
Fixes: 7f699bd149 (iio: frequency: adf4371: Add support for ADF4371 PLL)
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Stefan Popa <stefan.popa@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since every chip has a different whoami, we are not supporting all
existing variant of all chips. Add an explicit supported chips
list in Kconfig description.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This driver adds the initial support for the ON Semiconductor
NOA1305 Ambient Light Sensor.
Originally written by Sergei Miroshnichenko. Found here:
196d6cf897
Signed-off-by: Sergei M <fizik1@yandex.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Not even sure why it was there since the beginning. Just use IRQ
number in the sensor_data struct.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
in_accel_x_scale, in_accel_y_scale and in_accel_z_scale are always
the same. The scale is still defined to be in "info_mask_separate".
Userspace (iio-sensor-proxy and others) is not used to that and only
looks for "in_accel_scale" for the scaling factor to apply.
Change IIO_CHAN_INFO_SCALE from being separate in all channel to be
shared by type.
This removes in_accel_x_scale, in_accel_y_scale and in_accel_z_scale and
makes available in_accel_scale.
This is an ABI change, but hopefully in the 'no one will notice'
category. The cleanup in interface is worth the small risk that
there is a custom script out there somewhere that this will break.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use regulator_bulk_() APIs to shrink driver size.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Reviewed-by: Brian Masney <masneyb@onstation.org>
Tested-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use devm_iio_device_register, which removes the tsl2772_remove
function.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Reviewed-by: Brian Masney <masneyb@onstation.org>
Tested-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use devm_add_action_or_reset to call tsl2772_chip_off
when the device is removed.
This also fixes the issue that the chip is turned off
before the device is unregistered.
Not marked for stable as fairly hard to hit the bug and
this is in the middle of a set making other cleanups
to the driver. Hence will probably need explicit backporting.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Fixes: c06c4d7935 ("staging: iio: tsl2x7x/tsl2772: move out of staging")
Reviewed-by: Brian Masney <masneyb@onstation.org>
Tested-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use devm_add_action_or_reset to remove the call to
tsl2772_disable_regulators_action to simplify the error path.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Reviewed-by: Brian Masney <masneyb@onstation.org>
Tested-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: linux-iio@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use device-managed APIs to simplify the code.
The remove functions are redundant now and can
be deleted.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch is trying to cleanup for good the buffers operation functions.
There is no need of using preenable, all can be done into
postenable. Let's also use logical sequence of operations as
already done in accel driver.
Finally also rename the goto label using operation to perform and not
where it fails.
Not stable material as not fixing a 'bug' but rather bringing the
driver in line with general 'patterns' to allow a subsystem wide
cleanup.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch is trying to cleanup for good the buffers operation functions.
Let's rename the goto label using operation to perform and not
where it fails.
Not stable material as not fixing a 'bug' but rather bringing the
driver in line with general 'patterns' to allow a subsystem wide
cleanup.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch is trying to cleanup for good the buffers operation functions.
There is no need of using preenable, all can be done into
postenable. Let's also use logical sequence of operations as
already done in accel driver.
Finally also rename the goto label using operation to perform and not
where it fails.
Not stable material as not fixing a 'bug' but rather bringing the
driver in line with general 'patterns' to allow a subsystem wide
cleanup.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Linus Walleij