Enable RPA timeout during bluetooth initialization.
The RPA timeout value is used from hdev, which initialized from
debug_fs
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When using controller based address resolution, then the new address
types 0x02 and 0x03 are used. These types need to be converted back into
either public address or random address types.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sathish Narsimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The original return is NOTIFY_STOP, but notifier_call_chain would stop
the future call for register_pm_notifier even registered on other Kernel
modules with the same priority which value is zero.
Signed-off-by: Max Chou <max.chou@realtek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
For some reason they tend to squat on the very first CSR/
Cambridge Silicon Radio VID/PID instead of paying fees.
This is an extremely common problem; the issue goes as back as 2013
and these devices are only getting more popular, even rebranded by
reputable vendors and sold by retailers everywhere.
So, at this point in time there are hundreds of modern dongles reusing
the ID of what originally was an early Bluetooth 1.1 controller.
Linux is the only place where they don't work due to spotty checks
in our detection code. It only covered a minimum subset.
So what's the big idea? Take advantage of the fact that all CSR
chips report the same internal version as both the LMP sub-version and
HCI revision number. It always matches, couple that with the manufacturer
code, that rarely lies, and we now have a good idea of who is who.
Additionally, by compiling a list of user-reported HCI/lsusb dumps, and
searching around for legit CSR dongles in similar product ranges we can
find what CSR BlueCore firmware supported which Bluetooth versions.
That way we can narrow down ranges of fakes for each of them.
e.g. Real CSR dongles with LMP subversion 0x73 are old enough that
support BT 1.1 only; so it's a dead giveaway when some
third-party BT 4.0 dongle reuses it.
So, to sum things up; there are multiple classes of fake controllers
reusing the same 0A12:0001 VID/PID. This has been broken for a while.
Known 'fake' bcdDevices: 0x0100, 0x0134, 0x1915, 0x2520, 0x7558, 0x8891
IC markings on 0x7558: FR3191AHAL 749H15143 (???)
https://bugzilla.kernel.org/show_bug.cgi?id=60824
Fixes: 81cac64ba2 (Deal with USB devices that are faking CSR vendor)
Reported-by: Michał Wiśniewski <brylozketrzyn@gmail.com>
Tested-by: Mike Johnson <yuyuyak@gmail.com>
Tested-by: Ricardo Rodrigues <ekatonb@gmail.com>
Tested-by: M.Hanny Sabbagh <mhsabbagh@outlook.com>
Tested-by: Oussama BEN BRAHIM <b.brahim.oussama@gmail.com>
Tested-by: Ismael Ferreras Morezuelas <swyterzone@gmail.com>
Signed-off-by: Ismael Ferreras Morezuelas <swyterzone@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This fixes the kernel oops by removing unnecessary background scan
update from hci_adv_monitors_clear() which shouldn't invoke any work
queue.
The following test was performed.
- Run "rmmod btusb" and verify that no kernel oops is triggered.
Signed-off-by: Miao-chen Chou <mcchou@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This calls hci_update_background_scan() when there is any update on the
advertisement monitors. If there is at least one advertisement monitor,
the filtering policy of scan parameters should be 0x00. This also reports
device found mgmt events if there is at least one monitor.
The following cases were tested with btmgmt advmon-* commands.
(1) add a ADV monitor and observe that the passive scanning is
triggered.
(2) remove the last ADV monitor and observe that the passive scanning is
terminated.
(3) with a LE peripheral paired, repeat (1) and observe the passive
scanning continues.
(4) with a LE peripheral paired, repeat (2) and observe the passive
scanning continues.
(5) with a ADV monitor, suspend/resume the host and observe the passive
scanning continues.
Signed-off-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This adds the request handler of MGMT_OP_REMOVE_ADV_MONITOR command.
Note that the controller-based monitoring is not yet in place. This
removes the internal monitor(s) without sending HCI traffic, so the
request returns immediately.
The following test was performed.
- Issue btmgmt advmon-remove with valid and invalid handles.
Signed-off-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This adds the request handler of MGMT_OP_ADD_ADV_PATTERNS_MONITOR command.
Note that the controller-based monitoring is not yet in place. This tracks
the content of the monitor without sending HCI traffic, so the request
returns immediately.
The following manual test was performed.
- Issue btmgmt advmon-add with valid and invalid inputs.
- Issue btmgmt advmon-add more the allowed number of monitors.
Signed-off-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This adds the request handler of MGMT_OP_READ_ADV_MONITOR_FEATURES
command. Since the controller-based monitoring is not yet in place, this
report only the supported features but not the enabled features.
The following test was performed.
- Issuing btmgmt advmon-features.
Signed-off-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Since the classic device list now supports flags, convert the wakeable
list into a flag on the existing device list.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
In order to more easily add device flags to classic devices, create
a new type of bdaddr_list that supports setting flags.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch centralized the initialization of default parameters. This
is required to allow clients to more easily customize the default
system parameters.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This change adds support for reporting the BT_PKT_STATUS to the socket
CMSG data to allow the implementation of a packet loss correction on
erroneous data received on the SCO socket.
The patch was partially developed by Marcel Holtmann and validated by
Hsin-yu Chao.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
It is preferable to allow suspend even when Bluetooth has problems
preparing for sleep. When Bluetooth fails to finish preparing for
suspend, log the error and allow the suspend notifier to continue
instead.
To also make it clearer why suspend failed, change bt_dev_dbg to
bt_dev_err when handling the suspend timeout.
Fixes: dd522a7429 ("Bluetooth: Handle LE devices during suspend")
Reported-by: Len Brown <len.brown@intel.com>
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Let drivers have a hook to disable configuring scanning during suspend.
Drivers should use the device_may_wakeup function call to determine
whether hci should be configured for wakeup.
For example, an implementation for btusb may look like the following:
bool btusb_prevent_wake(struct hci_dev *hdev)
{
struct btusb_data *data = hci_get_drvdata(hdev);
return !device_may_wakeup(&data->udev->dev);
}
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Renamed BT_SUSPEND_COMPLETE to BT_SUSPEND_CONFIGURE_WAKE since it sets
up the event filter and whitelist for wake-up.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Enhanced Connection Complete event is use in conjunction with LL
Privacy and not Extended Advertising.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
In case LL Privacy is supported by the controller, it is also a good
idea to use the LE Enhanced Connection Complete event for getting all
information about the new connection and its addresses.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
With the Read Local Simple Pairing Options command it is possible to
retrieve the support for max encryption key size supported by the
controller and also if the controller correctly verifies the ECDH public
key during pairing.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Micrsoft defined a set for HCI vendor extensions. Check the following
link for details:
https://docs.microsoft.com/en-us/windows-hardware/drivers/bluetooth/microsoft-defined-bluetooth-hci-commands-and-events
This provides the basic framework to enable the extension and read its
supported features. Drivers still have to declare support for this
extension before it can be utilized by the host stack.
Signed-off-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When scheduling TX packets, send all SCO/eSCO packets first, check for
pending SCO/eSCO packets after every ACL/LE packet and send them if any
are pending. This is done to make sure that we can meet SCO deadlines
on slow interfaces like UART.
If we were to queue up multiple ACL packets without checking for a SCO
packet, we might miss the SCO timing. For example:
The time it takes to send a maximum size ACL packet (1024 bytes):
t = 10/8 * 1024 bytes * 8 bits/byte * 1 packet / baudrate
where 10/8 is uart overhead due to start/stop bits per byte
Replace t = 3.75ms (SCO deadline), which gives us a baudrate of 2730666.
At a baudrate of 3000000, if we didn't check for SCO packets within 1024
bytes, we would miss the 3.75ms timing window.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If Bluetooth fails to enter the suspended state correctly, restore the
state to running (re-enabling scans). PM_POST_SUSPEND is only sent to
notifiers that successfully return from PM_PREPARE_SUSPEND notification
so we should recover gracefully if it fails.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To handle BR/EDR devices, we first disable page scan and disconnect all
connected devices. Once that is complete, we add event filters (for
devices that can wake the system) and re-enable page scan.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Register for PM_SUSPEND_PREPARE and PM_POST_SUSPEND to make sure the
Bluetooth controller is prepared correctly for suspend/resume. Implement
the registration, scheduling and task handling portions only in this
patch.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This change fixes the off by one error in the erroneous command bit
masks which can lead to the erroneous data commands being sent to a
controller that doesn't support them.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This change introduces a wide band speech setting which allows higher
level clients to query the local controller support for wide band speech
as well as set the setting state when the radio is powered off.
Internally, this setting controls if erroneous data reporting is enabled
on the controller.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When processing SCO packets, the handle is wrongly assumed as 16-bit
value. The actual size is 12-bits and the other 4-bits are used for
packet flags.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
In function hci_is_blocked_key() RCU list is traversed with
list_for_each_entry() in RCU read-side CS.
Use list_for_each_entry_rcu() instead.
Signed-off-by: Madhuparna Bhowmik <madhuparnabhowmik10@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The checks for HCI_ISODATA_PKT packet type are required in a few
additional locations to allow sending/receiving of this new packet type.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This reuse __check_timeout on hci_sched_le following the same logic
used hci_sched_acl.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
MGMT command is added to receive the list of blocked keys from
user-space.
The list is used to:
1) Block keys from being distributed by the device during
the ke distribution phase of SMP.
2) Filter out any keys that were previously saved so
they are no longer used.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When utilizing BDADDR_PROPERTY and INVALID_BDADDR quirks together it
results in an unconfigured controller even if the bootloader provides
a valid address. Fix this by allowing a bootloader provided address
to mark the controller as configured.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Tested-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
During the setup() stage, HCI device drivers expect the chip to
acknowledge its setup() completion via vendor specific frames.
If userspace opens() such HCI device in HCI_USER_CHANNEL [1] mode,
the vendor specific frames are never tranmitted to the driver, as
they are filtered in hci_rx_work().
Allow HCI devices which operate in HCI_USER_CHANNEL mode to receive
frames if the HCI device is is HCI_INIT state.
[1] https://www.spinics.net/lists/linux-bluetooth/msg37345.html
Fixes: 23500189d7 ("Bluetooth: Introduce new HCI socket channel for user operation")
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
It looks like in hci_init4_req() the request is being
initialised from cpu-endian data but the packet is specified
to be little-endian. This causes an warning from sparse due
to __le16 to u16 conversion.
Fix this by using cpu_to_le16() on the two fields in the packet.
net/bluetooth/hci_core.c:845:27: warning: incorrect type in assignment (different base types)
net/bluetooth/hci_core.c:845:27: expected restricted __le16 [usertype] tx_len
net/bluetooth/hci_core.c:845:27: got unsigned short [usertype] le_max_tx_len
net/bluetooth/hci_core.c:846:28: warning: incorrect type in assignment (different base types)
net/bluetooth/hci_core.c:846:28: expected restricted __le16 [usertype] tx_time
net/bluetooth/hci_core.c:846:28: got unsigned short [usertype] le_max_tx_time
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
For testing and qualification purposes it is useful to allow changing
the minimum encryption key size value that the host stack is going to
enforce. This adds a new debugfs setting min_encrypt_key_size to achieve
this functionality.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This makes use of controller sets when using Extended Advertising
feature thus offloading the scheduling to the controller.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Changes made to add HCI Write Authenticated Payload timeout
command for LE Ping feature.
As per the Core Specification 5.0 Volume 2 Part E Section 7.3.94,
the following code changes implements
HCI Write Authenticated Payload timeout command for LE Ping feature.
Signed-off-by: Spoorthi Ravishankar Koppad <spoorthix.k@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This commit makes the kernel not send the next queued HCI command until
a command complete arrives for the last HCI command sent to the
controller. This change avoids a problem with some buggy controllers
(seen on two SKUs of QCA9377) that send an extra command complete event
for the previous command after the kernel had already sent a new HCI
command to the controller.
The problem was reproduced when starting an active scanning procedure,
where an extra command complete event arrives for the LE_SET_RANDOM_ADDR
command. When this happends the kernel ends up not processing the
command complete for the following commmand, LE_SET_SCAN_PARAM, and
ultimately behaving as if a passive scanning procedure was being
performed, when in fact controller is performing an active scanning
procedure. This makes it impossible to discover BLE devices as no device
found events are sent to userspace.
This problem is reproducible on 100% of the attempts on the affected
controllers. The extra command complete event can be seen at timestamp
27.420131 on the btmon logs bellow.
Bluetooth monitor ver 5.50
= Note: Linux version 5.0.0+ (x86_64) 0.352340
= Note: Bluetooth subsystem version 2.22 0.352343
= New Index: 80:C5:F2:8F:87:84 (Primary,USB,hci0) [hci0] 0.352344
= Open Index: 80:C5:F2:8F:87:84 [hci0] 0.352345
= Index Info: 80:C5:F2:8F:87:84 (Qualcomm) [hci0] 0.352346
@ MGMT Open: bluetoothd (privileged) version 1.14 {0x0001} 0.352347
@ MGMT Open: btmon (privileged) version 1.14 {0x0002} 0.352366
@ MGMT Open: btmgmt (privileged) version 1.14 {0x0003} 27.302164
@ MGMT Command: Start Discovery (0x0023) plen 1 {0x0003} [hci0] 27.302310
Address type: 0x06
LE Public
LE Random
< HCI Command: LE Set Random Address (0x08|0x0005) plen 6 #1 [hci0] 27.302496
Address: 15:60:F2:91:B2:24 (Non-Resolvable)
> HCI Event: Command Complete (0x0e) plen 4 #2 [hci0] 27.419117
LE Set Random Address (0x08|0x0005) ncmd 1
Status: Success (0x00)
< HCI Command: LE Set Scan Parameters (0x08|0x000b) plen 7 #3 [hci0] 27.419244
Type: Active (0x01)
Interval: 11.250 msec (0x0012)
Window: 11.250 msec (0x0012)
Own address type: Random (0x01)
Filter policy: Accept all advertisement (0x00)
> HCI Event: Command Complete (0x0e) plen 4 #4 [hci0] 27.420131
LE Set Random Address (0x08|0x0005) ncmd 1
Status: Success (0x00)
< HCI Command: LE Set Scan Enable (0x08|0x000c) plen 2 #5 [hci0] 27.420259
Scanning: Enabled (0x01)
Filter duplicates: Enabled (0x01)
> HCI Event: Command Complete (0x0e) plen 4 #6 [hci0] 27.420969
LE Set Scan Parameters (0x08|0x000b) ncmd 1
Status: Success (0x00)
> HCI Event: Command Complete (0x0e) plen 4 #7 [hci0] 27.421983
LE Set Scan Enable (0x08|0x000c) ncmd 1
Status: Success (0x00)
@ MGMT Event: Command Complete (0x0001) plen 4 {0x0003} [hci0] 27.422059
Start Discovery (0x0023) plen 1
Status: Success (0x00)
Address type: 0x06
LE Public
LE Random
@ MGMT Event: Discovering (0x0013) plen 2 {0x0003} [hci0] 27.422067
Address type: 0x06
LE Public
LE Random
Discovery: Enabled (0x01)
@ MGMT Event: Discovering (0x0013) plen 2 {0x0002} [hci0] 27.422067
Address type: 0x06
LE Public
LE Random
Discovery: Enabled (0x01)
@ MGMT Event: Discovering (0x0013) plen 2 {0x0001} [hci0] 27.422067
Address type: 0x06
LE Public
LE Random
Discovery: Enabled (0x01)
Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When flag HCI_QUIRK_USE_BDADDR_PROPERTY is set, we will read the
bluetooth address from dts. If the bluetooth address node is missing
from the dts we will enable it controller UNCONFIGURED state.
This patch enables the normal flow even if the BD address is missing
from the dts tree.
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Tested-by: Harish Bandi <c-hbandi@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add HCI_QUIRK_USE_BDADDR_PROPERTY to allow controllers to retrieve
the public Bluetooth address from the firmware node property
'local-bd-address'. If quirk is set and the property does not exist
or is invalid the controller is marked as unconfigured.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Tested-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Don't populate the const array hw_err on the stack but instead make
it static. Makes the object code smaller by 45 bytes:
Before:
text data bss dec hex filename
100880 21090 1088 123058 1e0b2 linux/net/bluetooth/hci_core.o
After:
text data bss dec hex filename
100739 21186 1088 123013 1e085 linux/net/bluetooth/hci_core.o
(gcc version 8.2.0 x86_64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add a hook to allow the BT driver to do device or command specific
handling in case of timeouts. This is to be used by Intel driver to
reset the device after certain number of timeouts.
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add the definitions for adding entries to the LE resolve list and
removing entries from the LE resolve list. When the LE resolve list
gets changed via HCI commands make sure that the internal storage of
the resolve list entries gets updated.
Signed-off-by: Ankit Navik <ankit.p.navik@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add a new quirk HCI_QUIRK_NON_PERSISTENT_SETUP allowing that a quirk that
runs setup() after every open() and not just after the first open().
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This event comes after connection complete event for incoming
connections. Since we now have different random address for
each instance, conn resp address is assigned from this event.
As of now only connection part is handled as we are not
enabling duration or max num of events while starting ext adv.
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This basically sets the random address for the adv instance
Random address can be set only if the instance is created which
is done in Set ext adv param.
Random address and rpa expire timer and flags have been added
to adv instance which will be used when the respective
instance is scheduled.
This introduces a hci_get_random_address() which returns the
own address type and random address (rpa or nrpa) based
on the instance flags and hdev flags. New function is required
since own address type should be known before setting adv params
but address can be set only after setting params.
< HCI Command: LE Set Advertising Set Random Address (0x08|0x0035) plen 7
Advertising handle: 0x00
Advertising random address: 3C:8E:56:9B:77:84 (OUI 3C-8E-56)
> HCI Event: Command Complete (0x0e) plen 4
LE Set Advertising Set Random Address (0x08|0x0035) ncmd 1
Status: Success (0x00)
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Sathish Narasimman