Locking range start and locking range length
attributes may be require to satisfy restrictions
exposed by OPAL2 geometry feature reporting.
Geometry reporting feature is described in TCG OPAL SSC,
section 3.1.1.4 (ALIGN, LogicalBlockSize, AlignmentGranularity
and LowestAlignedLBA).
4.3.5.2.1.1 RangeStart Behavior:
[ StartAlignment = (RangeStart modulo AlignmentGranularity) - LowestAlignedLBA ]
When processing a Set method or CreateRow method on the Locking
table for a non-Global Range row, if:
a) the AlignmentRequired (ALIGN above) column in the LockingInfo
table is TRUE;
b) RangeStart is non-zero; and
c) StartAlignment is non-zero, then the method SHALL fail and
return an error status code INVALID_PARAMETER.
4.3.5.2.1.2 RangeLength Behavior:
If RangeStart is zero, then
[ LengthAlignment = (RangeLength modulo AlignmentGranularity) - LowestAlignedLBA ]
If RangeStart is non-zero, then
[ LengthAlignment = (RangeLength modulo AlignmentGranularity) ]
When processing a Set method or CreateRow method on the Locking
table for a non-Global Range row, if:
a) the AlignmentRequired (ALIGN above) column in the LockingInfo
table is TRUE;
b) RangeLength is non-zero; and
c) LengthAlignment is non-zero, then the method SHALL fail and
return an error status code INVALID_PARAMETER
In userspace we stuck to logical block size reported by general
block device (via sysfs or ioctl), but we can not read
'AlignmentGranularity' or 'LowestAlignedLBA' anywhere else and
we need to get those values from sed-opal interface otherwise
we will not be able to report or avoid locking range setup
INVALID_PARAMETER errors above.
Signed-off-by: Ondrej Kozina <okozina@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Christian Brauner <brauner@kernel.org>
Tested-by: Milan Broz <gmazyland@gmail.com>
Link: https://lore.kernel.org/r/20230411090931.9193-2-okozina@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
It returns following attributes:
locking range start
locking range length
read lock enabled
write lock enabled
lock state (RW, RO or LK)
It can be retrieved by user authority provided the authority
was added to locking range via prior IOC_OPAL_ADD_USR_TO_LR
ioctl command. The command was extended to add user in ACE that
allows to read attributes listed above.
Signed-off-by: Ondrej Kozina <okozina@redhat.com>
Tested-by: Luca Boccassi <bluca@debian.org>
Tested-by: Milan Broz <gmazyland@gmail.com>
Link: https://lore.kernel.org/r/20230405111223.272816-6-okozina@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Refactors current code querying single column to use the
new helper. Real multi column usage will be added later.
Signed-off-by: Ondrej Kozina <okozina@redhat.com>
Tested-by: Luca Boccassi <bluca@debian.org>
Tested-by: Milan Broz <gmazyland@gmail.com>
Acked-by: Christian Brauner <brauner@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20230405111223.272816-5-okozina@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Extend ACE set of locking range attributes accessible to user
authority. This patch allows user authority to get following
locking range attribues when user get added to locking range via
IOC_OPAL_ADD_USR_TO_LR:
locking range start
locking range end
read lock enabled
write lock enabled
read locked
write locked
lock on reset
active key
Note: Admin1 authority always remains in the ACE. Otherwise
it breaks current userspace expecting Admin1 in the ACE (sedutils).
See TCG OPAL2 s.4.3.1.7 "ACE_Locking_RangeNNNN_Get_RangeStartToActiveKey".
Signed-off-by: Ondrej Kozina <okozina@redhat.com>
Tested-by: Luca Boccassi <bluca@debian.org>
Tested-by: Milan Broz <gmazyland@gmail.com>
Acked-by: Christian Brauner <brauner@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20230405111223.272816-4-okozina@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Move ACE construction away from add_user_to_lr routine
and refactor it to be used also in later code.
Also adds boolean operators defines from TCG Core
specification.
Signed-off-by: Ondrej Kozina <okozina@redhat.com>
Tested-by: Luca Boccassi <bluca@debian.org>
Tested-by: Milan Broz <gmazyland@gmail.com>
Link: https://lore.kernel.org/r/20230405111223.272816-3-okozina@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
While adding user authority in boolean ace value
of uid OPAL_LOCKINGRANGE_ACE_WRLOCKED or
OPAL_LOCKINGRANGE_ACE_RDLOCKED, it was added twice.
It seemed redundant when only single authority was added
in the set method aka { authority1, authority1, OR }:
TCG Storage Architecture Core Specification, 5.1.3.3 ACE_expression
"This is an alternative type where the options are either a uidref to an
Authority object or one of the boolean_ACE (AND = 0 and OR = 1) options.
This type is used within the AC_element list to form a postfix Boolean
expression of Authorities."
Signed-off-by: Ondrej Kozina <okozina@redhat.com>
Tested-by: Luca Boccassi <bluca@debian.org>
Tested-by: Milan Broz <gmazyland@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Christian Brauner <brauner@kernel.org>
Link: https://lore.kernel.org/r/20230405111223.272816-2-okozina@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Not every OPAL drive supports SUM (Single User Mode), so report this
information to userspace via the get-status ioctl so that we can adjust
the formatting options accordingly.
Tested on a kingston drive (which supports it) and a samsung one
(which does not).
Signed-off-by: Luca Boccassi <bluca@debian.org>
Link: https://lore.kernel.org/r/20230210010612.28729-1-luca.boccassi@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----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=k/vv
-----END PGP SIGNATURE-----
Merge tag 'for-6.2/block-2022-12-08' of git://git.kernel.dk/linux
Pull block updates from Jens Axboe:
- NVMe pull requests via Christoph:
- Support some passthrough commands without CAP_SYS_ADMIN (Kanchan
Joshi)
- Refactor PCIe probing and reset (Christoph Hellwig)
- Various fabrics authentication fixes and improvements (Sagi
Grimberg)
- Avoid fallback to sequential scan due to transient issues (Uday
Shankar)
- Implement support for the DEAC bit in Write Zeroes (Christoph
Hellwig)
- Allow overriding the IEEE OUI and firmware revision in configfs
for nvmet (Aleksandr Miloserdov)
- Force reconnect when number of queue changes in nvmet (Daniel
Wagner)
- Minor fixes and improvements (Uros Bizjak, Joel Granados, Sagi
Grimberg, Christoph Hellwig, Christophe JAILLET)
- Fix and cleanup nvme-fc req allocation (Chaitanya Kulkarni)
- Use the common tagset helpers in nvme-pci driver (Christoph
Hellwig)
- Cleanup the nvme-pci removal path (Christoph Hellwig)
- Use kstrtobool() instead of strtobool (Christophe JAILLET)
- Allow unprivileged passthrough of Identify Controller (Joel
Granados)
- Support io stats on the mpath device (Sagi Grimberg)
- Minor nvmet cleanup (Sagi Grimberg)
- MD pull requests via Song:
- Code cleanups (Christoph)
- Various fixes
- Floppy pull request from Denis:
- Fix a memory leak in the init error path (Yuan)
- Series fixing some batch wakeup issues with sbitmap (Gabriel)
- Removal of the pktcdvd driver that was deprecated more than 5 years
ago, and subsequent removal of the devnode callback in struct
block_device_operations as no users are now left (Greg)
- Fix for partition read on an exclusively opened bdev (Jan)
- Series of elevator API cleanups (Jinlong, Christoph)
- Series of fixes and cleanups for blk-iocost (Kemeng)
- Series of fixes and cleanups for blk-throttle (Kemeng)
- Series adding concurrent support for sync queues in BFQ (Yu)
- Series bringing drbd a bit closer to the out-of-tree maintained
version (Christian, Joel, Lars, Philipp)
- Misc drbd fixes (Wang)
- blk-wbt fixes and tweaks for enable/disable (Yu)
- Fixes for mq-deadline for zoned devices (Damien)
- Add support for read-only and offline zones for null_blk
(Shin'ichiro)
- Series fixing the delayed holder tracking, as used by DM (Yu,
Christoph)
- Series enabling bio alloc caching for IRQ based IO (Pavel)
- Series enabling userspace peer-to-peer DMA (Logan)
- BFQ waker fixes (Khazhismel)
- Series fixing elevator refcount issues (Christoph, Jinlong)
- Series cleaning up references around queue destruction (Christoph)
- Series doing quiesce by tagset, enabling cleanups in drivers
(Christoph, Chao)
- Series untangling the queue kobject and queue references (Christoph)
- Misc fixes and cleanups (Bart, David, Dawei, Jinlong, Kemeng, Ye,
Yang, Waiman, Shin'ichiro, Randy, Pankaj, Christoph)
* tag 'for-6.2/block-2022-12-08' of git://git.kernel.dk/linux: (247 commits)
blktrace: Fix output non-blktrace event when blk_classic option enabled
block: sed-opal: Don't include <linux/kernel.h>
sed-opal: allow using IOC_OPAL_SAVE for locking too
blk-cgroup: Fix typo in comment
block: remove bio_set_op_attrs
nvmet: don't open-code NVME_NS_ATTR_RO enumeration
nvme-pci: use the tagset alloc/free helpers
nvme: add the Apple shared tag workaround to nvme_alloc_io_tag_set
nvme: only set reserved_tags in nvme_alloc_io_tag_set for fabrics controllers
nvme: consolidate setting the tagset flags
nvme: pass nr_maps explicitly to nvme_alloc_io_tag_set
block: bio_copy_data_iter
nvme-pci: split out a nvme_pci_ctrl_is_dead helper
nvme-pci: return early on ctrl state mismatch in nvme_reset_work
nvme-pci: rename nvme_disable_io_queues
nvme-pci: cleanup nvme_suspend_queue
nvme-pci: remove nvme_pci_disable
nvme-pci: remove nvme_disable_admin_queue
nvme: merge nvme_shutdown_ctrl into nvme_disable_ctrl
nvme: use nvme_wait_ready in nvme_shutdown_ctrl
...
Usually when closing a crypto device (eg: dm-crypt with LUKS) the
volume key is not required, as it requires root privileges anyway, and
root can deny access to a disk in many ways regardless. Requiring the
volume key to lock the device is a peculiarity of the OPAL
specification.
Given we might already have saved the key if the user requested it via
the 'IOC_OPAL_SAVE' ioctl, we can use that key to lock the device if no
key was provided here and the locking range matches, and the user sets
the appropriate flag with 'IOC_OPAL_SAVE'. This allows integrating OPAL
with tools and libraries that are used to the common behaviour and do
not ask for the volume key when closing a device.
Callers can always pass a non-zero key and it will be used regardless,
as before.
Suggested-by: Štěpán Horáček <stepan.horacek@gmail.com>
Signed-off-by: Luca Boccassi <bluca@debian.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Christian Brauner <brauner@kernel.org>
Link: https://lore.kernel.org/r/20221206092913.4625-1-luca.boccassi@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In accordance with [1] the DMA-able memory buffers must be
cacheline-aligned otherwise the cache writing-back and invalidation
performed during the mapping may cause the adjacent data being lost. It's
specifically required for the DMA-noncoherent platforms [2]. Seeing the
opal_dev.{cmd,resp} buffers are implicitly used for DMAs in the NVME and
SCSI/SD drivers in framework of the nvme_sec_submit() and sd_sec_submit()
methods respectively they must be cacheline-aligned to prevent the denoted
problem. One of the option to guarantee that is to kmalloc the buffers
[2]. Let's explicitly allocate them then instead of embedding into the
opal_dev structure instance.
Note this fix was inspired by the commit c94b7f9bab ("nvme-hwmon:
kmalloc the NVME SMART log buffer").
[1] Documentation/core-api/dma-api.rst
[2] Documentation/core-api/dma-api-howto.rst
Fixes: 455a7b238c ("block: Add Sed-opal library")
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20221107203944.31686-1-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Provide a mechanism to retrieve basic status information about
the device, including the "supported" flag indicating whether
SED-OPAL is supported. The information returned is from the various
feature descriptors received during the discovery0 step, and so
this ioctl does nothing more than perform the discovery0 step
and then save the information received. See "struct opal_status"
and OPAL_FL_* bits for the status information currently returned.
This is necessary to be able to check whether a device is OPAL
enabled, set up, locked or unlocked from userspace programs
like systemd-cryptsetup and libcryptsetup. Right now we just
have to assume the user 'knows' or blindly attempt setup/lock/unlock
operations.
Signed-off-by: Douglas Miller <dougmill@linux.vnet.ibm.com>
Tested-by: Luca Boccassi <bluca@debian.org>
Reviewed-by: Scott Bauer <sbauer@plzdonthack.me>
Acked-by: Christian Brauner (Microsoft) <brauner@kernel.org>
Link: https://lore.kernel.org/r/20220816140713.84893-1-luca.boccassi@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
There is no good reason to keep genhd.h separate from the main blkdev.h
header that includes it. So fold the contents of genhd.h into blkdev.h
and remove genhd.h entirely.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20220124093913.742411-4-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In function 'activate_lsp', rather than hard-coding the short atom
header(0x83), we need to let the function 'add_short_atom_header' append
the header based on the parameter being appended.
The parameter has been defined in Section 3.1.2.1 of
https://trustedcomputinggroup.org/wp-content/uploads/TCG_Storage-Opal_Feature_Set_Single_User_Mode_v1-00_r1-00-Final.pdf
Reviewed-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Revanth Rajashekar <revanth.rajashekar@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This patch introduces Opal Datastore UID.
The generic read/write table ioctl can use this UID
to access the Opal Datastore.
Reviewed-by: Scott Bauer <sbauer@plzdonthack.me>
Reviewed-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Revanth Rajashekar <revanth.rajashekar@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This feature gives the user RW access to any opal table with admin1
authority. The flags described in the new structure determines if the user
wants to read/write the data. Flags are checked for valid values in
order to allow future features to be added to the ioctl.
The user can provide the desired table's UID. Also, the ioctl provides a
size and offset field and internally will loop data accesses to return
the full data block. Read overrun is prevented by the initiator's
sec_send_recv() backend. The ioctl provides a private field with the
intention to accommodate any future expansions to the ioctl.
Reviewed-by: Scott Bauer <sbauer@plzdonthack.me>
Reviewed-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Revanth Rajashekar <revanth.rajashekar@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This patch refactors the existing "write_shadowmbr" func and
creates a new generalized function "generic_table_write_data",
to write data to any opal table. Also, a few cleanups are included
in this patch.
Reviewed-by: Scott Bauer <sbauer@plzdonthack.me>
Reviewed-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Revanth Rajashekar <revanth.rajashekar@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
sparse warns about incorrect type when using __be64 data.
It is not being converted to CPU-endian but it should be.
Fixes these sparse warnings:
../block/sed-opal.c:375:20: warning: incorrect type in assignment (different base types)
../block/sed-opal.c:375:20: expected unsigned long long [usertype] align
../block/sed-opal.c:375:20: got restricted __be64 const [usertype] alignment_granularity
../block/sed-opal.c:376:25: warning: incorrect type in assignment (different base types)
../block/sed-opal.c:376:25: expected unsigned long long [usertype] lowest_lba
../block/sed-opal.c:376:25: got restricted __be64 const [usertype] lowest_aligned_lba
Fixes: 455a7b238c ("block: Add Sed-opal library")
Cc: Scott Bauer <scott.bauer@intel.com>
Cc: Rafael Antognolli <rafael.antognolli@intel.com>
Cc: linux-block@vger.kernel.org
Reviewed-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In the function 'response_parse', num_entries will never be 0 as
slen is checked for 0. Hence, the condition 'if (num_entries == 0)'
can never be true.
Signed-off-by: Revanth Rajashekar <revanth.rajashekar@intel.com>
Reviewed-by: Scott Bauer <sbauer@plzdonthack.me>
Reviewed-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Check whether the shadow mbr does fit in the provided space on the
target. Also a proper firmware should handle this case and return an
error we may prevent problems or even damage with crappy firmwares.
Signed-off-by: Jonas Rabenstein <jonas.rabenstein@studium.uni-erlangen.de>
Signed-off-by: David Kozub <zub@linux.fjfi.cvut.cz>
Reviewed-by: Scott Bauer <sbauer@plzdonthack.me>
Reviewed-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Allow modification of the shadow mbr. If the shadow mbr is not marked as
done, this data will be presented read only as the device content. Only
after marking the shadow mbr as done and unlocking a locking range the
actual content is accessible.
Co-authored-by: David Kozub <zub@linux.fjfi.cvut.cz>
Signed-off-by: Jonas Rabenstein <jonas.rabenstein@studium.uni-erlangen.de>
Signed-off-by: David Kozub <zub@linux.fjfi.cvut.cz>
Reviewed-by: Scott Bauer <sbauer@plzdonthack.me>
Reviewed-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Enable users to mark the shadow mbr as done without completely
deactivating the shadow mbr feature. This may be useful on reboots,
when the power to the disk is not disconnected in between and the shadow
mbr stores the required boot files. Of course, this saves also the
(few) commands required to enable the feature if it is already enabled
and one only wants to mark the shadow mbr as done.
Co-authored-by: David Kozub <zub@linux.fjfi.cvut.cz>
Signed-off-by: Jonas Rabenstein <jonas.rabenstein@studium.uni-erlangen.de>
Signed-off-by: David Kozub <zub@linux.fjfi.cvut.cz>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed by: Scott Bauer <sbauer@plzdonthack.me>
Reviewed-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
'who' an unsigned variable in stucture opal_session_info
can never be lesser than zero. Hence, the condition
"who < OPAL_ADMIN1" can never be true.
Signed-off-by: Revanth Rajashekar <revanth.rajashekar@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
PSID is a 32 character password printed on the drive label,
to prove its physical access. This PSID reverttper function
is very useful to regain the control over the drive when it
is locked and the user can no longer access it because of some
failures. However, *all the data on the drive is completely
erased*. This method is advisable only when the user is exhausted
of all other recovery methods.
PSID capabilities are described in:
https://trustedcomputinggroup.org/wp-content/uploads/TCG_Storage-Opal_Feature_Set_PSID_v1.00_r1.00.pdf
Signed-off-by: Revanth Rajashekar <revanth.rajashekar@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
All these files have some form of the usual GPLv2 boilerplate. Switch
them to use SPDX tags instead.
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
As the function is responsible for executing the individual steps supplied
in the steps argument, execute_steps is a more descriptive name than the
rather generic next.
Signed-off-by: David Kozub <zub@linux.fjfi.cvut.cz>
Reviewed-by: Scott Bauer <sbauer@plzdonthack.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Originally each of the opal functions that call next include
opal_discovery0 in the array of steps. This is superfluous and
can be done always inside next.
Acked-by: Jon Derrick <jonathan.derrick@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Scott Bauer <sbauer@plzdonthack.me>
Signed-off-by: David Kozub <zub@linux.fjfi.cvut.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The steps argument is only read by the next function, so it can
be passed directly as an argument rather than via opal_dev.
Normally, the steps is an array on the stack, so the pointer stops
being valid then the function that set opal_dev.steps returns.
If opal_dev.steps was not set to NULL before return it would become
a dangling pointer. When the steps are passed as argument this
becomes easier to see and more difficult to misuse.
Acked-by: Jon Derrick <jonathan.derrick@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Scott Bauer <sbauer@plzdonthack.me>
Signed-off-by: David Kozub <zub@linux.fjfi.cvut.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Replace integer literals by Opal tokens defined in opal_proto.h where
possible.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jon Derrick <jonathan.derrick@intel.com>
Reviewed-by: Scott Bauer <sbauer@plzdonthack.me>
Signed-off-by: David Kozub <zub@linux.fjfi.cvut.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Instead of having multiple places defining the same argument list to get
a specific column of a sed-opal table, provide a generic version and
call it from those functions.
Co-authored-by: David Kozub <zub@linux.fjfi.cvut.cz>
Signed-off-by: Jonas Rabenstein <jonas.rabenstein@studium.uni-erlangen.de>
Signed-off-by: David Kozub <zub@linux.fjfi.cvut.cz>
Reviewed-by: Scott Bauer <sbauer@plzdonthack.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Define OPAL_LIFECYCLE token and use it instead of literals in
get_lsp_lifecycle.
Acked-by: Jon Derrick <jonathan.derrick@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Scott Bauer <sbauer@plzdonthack.me>
Signed-off-by: David Kozub <zub@linux.fjfi.cvut.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Split the header generation from the (normal) memcpy part if a
bytestring is copied into the command buffer. This allows in-place
generation of the bytestring content. For example, copy_from_user may be
used without an intermediate buffer.
Signed-off-by: Jonas Rabenstein <jonas.rabenstein@studium.uni-erlangen.de>
Signed-off-by: David Kozub <zub@linux.fjfi.cvut.cz>
Reviewed-by: Scott Bauer <sbauer@plzdonthack.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add function address (and if available its symbol) to the message if a
step function fails.
Signed-off-by: Jonas Rabenstein <jonas.rabenstein@studium.uni-erlangen.de>
Signed-off-by: David Kozub <zub@linux.fjfi.cvut.cz>
Reviewed-by: Scott Bauer <sbauer@plzdonthack.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jon Derrick <jonathan.derrick@intel.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
response_get_token had already been in place, its functionality had
been duplicated within response_get_{u64,bytestring} with the same error
handling. Unify the handling by reusing response_get_token within the
other functions.
Co-authored-by: Jonas Rabenstein <jonas.rabenstein@studium.uni-erlangen.de>
Signed-off-by: David Kozub <zub@linux.fjfi.cvut.cz>
Signed-off-by: Jonas Rabenstein <jonas.rabenstein@studium.uni-erlangen.de>
Reviewed-by: Scott Bauer <sbauer@plzdonthack.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
response_get_{string,u64} include error handling for argument resp being
NULL but response_get_token does not handle this.
Make all three of response_get_{string,u64,token} handle NULL resp in
the same way.
Co-authored-by: Jonas Rabenstein <jonas.rabenstein@studium.uni-erlangen.de>
Signed-off-by: David Kozub <zub@linux.fjfi.cvut.cz>
Signed-off-by: Jonas Rabenstein <jonas.rabenstein@studium.uni-erlangen.de>
Reviewed-by: Scott Bauer <sbauer@plzdonthack.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Every step starts with resetting the cmd buffer as well as the comid and
constructs the appropriate OPAL_CALL command. Consequently, those
actions may be combined into one generic function. On should take care
that the opening and closing tokens for the argument list are already
emitted by cmd_start and cmd_finalize respectively and thus must not be
additionally added.
Co-authored-by: Jonas Rabenstein <jonas.rabenstein@studium.uni-erlangen.de>
Signed-off-by: David Kozub <zub@linux.fjfi.cvut.cz>
Signed-off-by: Jonas Rabenstein <jonas.rabenstein@studium.uni-erlangen.de>
Reviewed-by: Scott Bauer <sbauer@plzdonthack.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Every step ends by calling cmd_finalize (via finalize_and_send)
yet every step adds the token OPAL_ENDLIST on its own. Moving
this into cmd_finalize decreases code duplication.
Co-authored-by: Jonas Rabenstein <jonas.rabenstein@studium.uni-erlangen.de>
Signed-off-by: David Kozub <zub@linux.fjfi.cvut.cz>
Signed-off-by: Jonas Rabenstein <jonas.rabenstein@studium.uni-erlangen.de>
Reviewed-by: Scott Bauer <sbauer@plzdonthack.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
All add_token_* functions have a common set of conditions that have to
be checked. Use a common function for those checks in order to avoid
different behaviour as well as code duplication.
Acked-by: Jon Derrick <jonathan.derrick@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Scott Bauer <sbauer@plzdonthack.me>
Co-authored-by: David Kozub <zub@linux.fjfi.cvut.cz>
Signed-off-by: Jonas Rabenstein <jonas.rabenstein@studium.uni-erlangen.de>
Signed-off-by: David Kozub <zub@linux.fjfi.cvut.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Also the values of OPAL_UID_LENGTH and OPAL_METHOD_LENGTH are the same,
it is weird to use OPAL_UID_LENGTH for the definition of the methods.
Signed-off-by: Jonas Rabenstein <jonas.rabenstein@studium.uni-erlangen.de>
Signed-off-by: David Kozub <zub@linux.fjfi.cvut.cz>
Reviewed-by: Scott Bauer <sbauer@plzdonthack.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This should make no change in functionality.
The formatting changes were triggered by checkpatch.pl.
Reviewed-by: Scott Bauer <sbauer@plzdonthack.me>
Reviewed-by: Jon Derrick <jonathan.derrick@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David Kozub <zub@linux.fjfi.cvut.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The implementation of IOC_OPAL_ENABLE_DISABLE_MBR handled the value
opal_mbr_data.enable_disable incorrectly: enable_disable is expected
to be one of OPAL_MBR_ENABLE(0) or OPAL_MBR_DISABLE(1). enable_disable
was passed directly to set_mbr_done and set_mbr_enable_disable where
is was interpreted as either OPAL_TRUE(1) or OPAL_FALSE(0). The end
result was that calling IOC_OPAL_ENABLE_DISABLE_MBR with OPAL_MBR_ENABLE
actually disabled the shadow MBR and vice versa.
This patch adds correct conversion from OPAL_MBR_DISABLE/ENABLE to
OPAL_FALSE/TRUE. The change affects existing programs using
IOC_OPAL_ENABLE_DISABLE_MBR but this is typically used only once when
setting up an Opal drive.
Acked-by: Jon Derrick <jonathan.derrick@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Scott Bauer <sbauer@plzdonthack.me>
Signed-off-by: David Kozub <zub@linux.fjfi.cvut.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
resp->num is the number of tokens in resp->tok[]. It gets set in
response_parse(). So if n == resp->num then we're reading beyond the
end of the data.
Fixes: 455a7b238c ("block: Add Sed-opal library")
Reviewed-by: Scott Bauer <scott.bauer@intel.com>
Tested-by: Scott Bauer <scott.bauer@intel.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=RVhK
-----END PGP SIGNATURE-----
Merge tag 'for-4.17/block-20180402' of git://git.kernel.dk/linux-block
Pull block layer updates from Jens Axboe:
"It's a pretty quiet round this time, which is nice. This contains:
- series from Bart, cleaning up the way we set/test/clear atomic
queue flags.
- series from Bart, fixing races between gendisk and queue
registration and removal.
- set of bcache fixes and improvements from various folks, by way of
Michael Lyle.
- set of lightnvm updates from Matias, most of it being the 1.2 to
2.0 transition.
- removal of unused DIO flags from Nikolay.
- blk-mq/sbitmap memory ordering fixes from Omar.
- divide-by-zero fix for BFQ from Paolo.
- minor documentation patches from Randy.
- timeout fix from Tejun.
- Alpha "can't write a char atomically" fix from Mikulas.
- set of NVMe fixes by way of Keith.
- bsg and bsg-lib improvements from Christoph.
- a few sed-opal fixes from Jonas.
- cdrom check-disk-change deadlock fix from Maurizio.
- various little fixes, comment fixes, etc from various folks"
* tag 'for-4.17/block-20180402' of git://git.kernel.dk/linux-block: (139 commits)
blk-mq: Directly schedule q->timeout_work when aborting a request
blktrace: fix comment in blktrace_api.h
lightnvm: remove function name in strings
lightnvm: pblk: remove some unnecessary NULL checks
lightnvm: pblk: don't recover unwritten lines
lightnvm: pblk: implement 2.0 support
lightnvm: pblk: implement get log report chunk
lightnvm: pblk: rename ppaf* to addrf*
lightnvm: pblk: check for supported version
lightnvm: implement get log report chunk helpers
lightnvm: make address conversions depend on generic device
lightnvm: add support for 2.0 address format
lightnvm: normalize geometry nomenclature
lightnvm: complete geo structure with maxoc*
lightnvm: add shorten OCSSD version in geo
lightnvm: add minor version to generic geometry
lightnvm: simplify geometry structure
lightnvm: pblk: refactor init/exit sequences
lightnvm: Avoid validation of default op value
lightnvm: centralize permission check for lightnvm ioctl
...
The length must be given as bytes and not as 4 bit tuples.
Reviewed-by: Scott Bauer <scott.bauer@intel.com>
Signed-off-by: Jonas Rabenstein <jonas.rabenstein@studium.uni-erlangen.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Tokens are prefixed by a variable length of bytes. If a bytestring is
not stored in an tiny or short atom, we have to skip more than one byte
in order to have the actual bytes not prefixed by the bytes describing
the actual length of the string.
Acked-by: Jonathan Derrick <jonathan.derrick@intel.com>
Signed-off-by: Jonas Rabenstein <jonas.rabenstein@studium.uni-erlangen.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
On lkml suggestions were made to split up such trivial typo fixes into per subsystem
patches:
--- a/arch/x86/boot/compressed/eboot.c
+++ b/arch/x86/boot/compressed/eboot.c
@@ -439,7 +439,7 @@ setup_uga32(void **uga_handle, unsigned long size, u32 *width, u32 *height)
struct efi_uga_draw_protocol *uga = NULL, *first_uga;
efi_guid_t uga_proto = EFI_UGA_PROTOCOL_GUID;
unsigned long nr_ugas;
- u32 *handles = (u32 *)uga_handle;;
+ u32 *handles = (u32 *)uga_handle;
efi_status_t status = EFI_INVALID_PARAMETER;
int i;
This patch is the result of the following script:
$ sed -i 's/;;$/;/g' $(git grep -E ';;$' | grep "\.[ch]:" | grep -vwE 'for|ia64' | cut -d: -f1 | sort | uniq)
... followed by manual review to make sure it's all good.
Splitting this up is just crazy talk, let's get over with this and just do it.
Reported-by: Pavel Machek <pavel@ucw.cz>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Users who are booting off their Opal enabled drives are having
issues when they have a shadow MBR set up after s3/resume cycle.
When the Drive has a shadow MBR setup the MBRDone flag is set to
false upon power loss (S3/S4/S5). When the MBRDone flag is false
I/O to LBA 0 -> LBA_END_MBR are remapped to the shadow mbr
of the drive. If the drive contains useful data in the 0 -> end_mbr
range upon s3 resume the user can never get to that data as the
drive will keep remapping it to the MBR. To fix this when we unlock
on S3 resume, we need to tell the drive that we're done with the
shadow mbr (even though we didnt use it) by setting true to MBRDone.
This way the drive will stop the remapping and the user can access
their data.
Acked-by Jon Derrick: <jonathan.derrick@intel.com>
Signed-off-by: Scott Bauer <scott.bauer@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Lets not flood the kernel log with messages unless
the user requests so.
Signed-off-by: Scott Bauer <scott.bauer@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Ondrej Kozina