The logic responsible for processing the event is
no different across different firmware binaries.
The difference that needs to be dealt with is the
ABI of data structures.
The intermediate structure uses __le32 to avoid
extra memory allocations to byteswap
variable-length substructures (i.e. host mem
chunks).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Makes it more readable and fixes checkpatch warnings:
drivers/net/wireless/ath/ath10k/debug.c:593: WARNING: quoted string split across lines
drivers/net/wireless/ath/ath10k/debug.c:594: WARNING: quoted string split across lines
drivers/net/wireless/ath/ath10k/debug.c:595: WARNING: quoted string split across lines
drivers/net/wireless/ath/ath10k/debug.c:596: WARNING: quoted string split across lines
drivers/net/wireless/ath/ath10k/debug.c:597: WARNING: quoted string split across lines
drivers/net/wireless/ath/ath10k/debug.c:599: WARNING: quoted string split across lines
drivers/net/wireless/ath/ath10k/debug.c:600: WARNING: quoted string split across lines
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The function may return an -ENODEV if debugfs is
disabled in kernel. This should originally be
guarded by ath10k's Kconfig but it still makes
sense to check for the non-NULL errno return
value.
Reported-by: Matteo Croce <matteo@openwrt.org>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
10.1 firmware does not have an official way to
cause assert on purpose, but it can be done with
carefully crafted WMI command. This is a different
kind of crash from the 'hard' crash, which is
a bad memory dereference.
Different crashes decode in different manners, so
this will help the crash-report testing as well as
offer better ways to test firmware failure and
recovery.
kvalo: move the wmi command creation to debug.c, modify
the info print
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add testmode interface for starting and using UTF firmware which is used to run
factory tests. This is implemented by adding new state ATH10K_STATE_UTF and user
space can enable this state with ATH10K_TM_CMD_UTF_START command. To go back to
normal mode user space can send ATH10K_TM_CMD_UTF_STOP.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
On 32bit systems the bitmap was too small and it
was overwritten partially by the stat completion
structure. This was visible with 10.2 firmware
only due to it using a few of the last service
ids.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This makes it easier to log and debug via tracing
with more than 1 ath10k device on a system.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This makes it a lot easier to log and debug
messages if there's more than 1 ath10k device on a
system.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Sometimes users forget to include important info like firmware version,
so better to print all the info.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Store the firmware registers and other relevant data to a firmware crash dump
file and provide it to user-space via debugfs. Should help with figuring out
why the firmware crashed.
kvalo: remove dbglog support, rework and refactor the code to avoid ifdefs and
otherwise simplify it as well
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The 10.x and main firmware branches have
conflicting WMI service bitmap definitions.
This also fixes WMI services parsing on big-endian
hosts and changes debugfs output to be more human
friendly.
kvalo: remove braces and the last semicolon from SVCSTR()
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Different firmware may support different numbers of
vdevs. Use value that is always out of range for all
firmware.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Allow to setup maximum subframes for AMSDU and AMPDU aggregation
via debugfs htt_max_amsdu_ampdu file.
Eg.
echo "2 64" > htt_max_amsdu_ampdu
will setup maximum amsdu subframes equal 2 and
maximum ampdu subframes equal to 64.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
As pointed out by Michal Kazior, add extra pdev stats
for 10.1 firmware.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
FW stats does provide the Rx rate information. Add this.
Tested with firmware 10x firmware.
Increase buffer size so more peers can be shown.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Using the macro to convert the MAC address from WMI word
format to char array has lead to the wrong peer mac
address printed out while retrieving the peer stats from
FW. Fix this.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Reviewed-By: Michał Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Command WMI_FORCE_FW_HANG_CMDID is not supported in firmware 10.1.
In order to have firmware crash simulation functionality also
in firmware 10.1 driver can force firmware crash by performing not allowed
operation. Driver can deliberately crash firmware when setting vdev param for
vdev id out of range. This patch introduces two keywords to simulate_fw_crash:
'soft' which will cause firmware crash that is recoverable
by warm firmware reset but supported only in main firmware.
'hard' which will cause firmware crash recoverable by cold
firmware reset, this option works for both firmwares.
Commands to trigger firmware soft/hard crash:
echo 'soft' > /sys/kernel/debug/ieee80211/phyX/ath10k/simulate_fw_crash
echo 'hard' > /sys/kernel/debug/ieee80211/phyX/ath10k/simulate_fw_crash
kvalo: remove '\n' before checking the command and simplify how buf is null
terminated
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware dbglogs can be now enabled through fw_dbglog file. To enable all
possible log messages run:
echo 0xffffffff > /sys/kernel/debug/ieee80211/phy0/ath10k/fw_dbglog
And to put back firmare defaults use 0x0:
echo 0x0 > /sys/kernel/debug/ieee80211/phy0/ath10k/fw_dbglog
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Sometimes for DFS testing is required to stay on current channel even after
radar detected. This patch allows to enable/disable radar detected event to be
passed to mac80211.
By default radar detected event in not blocked.
To block it:
echo 1 > /sys/kernel/debug/ieee80211/phyX/ath10k/dfs_block_radar_events
To unblock again:
echo 0 > /sys/kernel/debug/ieee80211/phyX/ath10k/dfs_block_radar_events
Inform about blocking radar detected event even when logs are disabled
for throughput/performance reasons.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Handle phyerr, dfs event, radar_report and fft_report.
Add also debugfs dfs_simulate_radar and dfs_stats files.
Use ath dfs pattern detector.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath10k_debug_start() was not called with conf_mutex, fix that. Also there was a
deadlock in ath10k_debug_stop(), rename it to ath10k_debug_destroy() and call
it only when the device is destroyed.
Reported-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This can be useful for testing. To perform a
forced firmware crash write 'crash' to
'simulate_fw_crash' debugfs file. E.g.
echo crash > /sys/kernel/debug/ieee80211/phy1/ath10k/simulate_fw_crash
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If the device is not running then there may be no
FW at all to send the query to. If the FW is
already there it might still trigger a crash if
the command is sent before the device is fully
initialized.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Here's a new mac80211 driver for Qualcomm Atheros 802.11ac QCA98xx devices.
A major difference from ath9k is that there's now a firmware and
that's why we had to implement a new driver.
The wiki page for the driver is:
http://wireless.kernel.org/en/users/Drivers/ath10k
The driver has had many authors, they are listed here alphabetically:
Bartosz Markowski <bartosz.markowski@tieto.com>
Janusz Dziedzic <janusz.dziedzic@tieto.com>
Kalle Valo <kvalo@qca.qualcomm.com>
Marek Kwaczynski <marek.kwaczynski@tieto.com>
Marek Puzyniak <marek.puzyniak@tieto.com>
Michal Kazior <michal.kazior@tieto.com>
Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Michal Kazior