CIO LDO status check seems to be broken on OMAP3630+ chips, and it's
also quite unclear what LDO status actually tells and when its status
changes.
This patch removes the whole check on the grounds that if there's a
problem with the LDO, we should anyway catch the problem as we check the
CIO power state and CIO reset status.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DSI_DSIPHY_CFG10 register can be used to override DSI lane state. Add
functions to configure and enable the override, and to disable the
override.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
OMAP4 has clocks set up in a bit interesting way, causing, for example,
the DSS's "ick" to be called "dss_fck".
This patch changes the debugfs output to show both the DSS's name for
the clock (ie. basically the clock alias), and the real name from the
clock struct.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Convert simple/strict_strto* functions to kstrto* functions. Only simple
cases are converted.
simple_strto* uses are still left to places where it is used to parse
numbers from a list of numbers. These need some other solution than
kstrto*.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The clock sources for DISPC_FCLK and LCD1_CLK are now specified in the board file.
There is no need for the hack config "CONFIG_OMAP2_DSS_USE_DSI_PLL" anymore.
Introduce function dpi_use_dsi_pll() which checks for the clock sources to decide
whether DSI PLL is to be used or not.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Move some of the configurable HDMI PLL parameters to dssdev.clock struct.
Cleanup the function hdmi_compute_pll() by using the parameters defined in the
board file and do some cosmetic modifications.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add enum dss_clock_source in dssdev.clocks struct so that the clock sources can
be specified in the board file.
Replace hard coded clock sources in dsi.c, dpi.c and replace them with the new
clock source members in dssdev.clocks. Modify the sdp4430_lcd_device struct in
board-4430sdp.c to specify clock sources for DISPC_FCLK, LCD1_CLK and DSI1_FCLK.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Change enum dss_clk_source to omap_dss_clock_source and move it to
'plat/display.h'. Change the enum members to attach "OMAP_" in the beginning.
These changes are done in order to specify the clock sources for DSS in the
board file.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We can use __exit for the driver remove function in plain dss panels
(ie. those that do not need i2c or spi).
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omap_dss_register_device and omap_dss_unregister_device can only be
called from core.c, so we can make it static.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
VENC code was missing omap_dss_start/stop_device calls. This didn't
cause any problems as VENC could not be compiled as a module, but
nevertheless it's better to add the calls.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Currently omapfb does an implicit display update (for manual update
displays) on unblank.
There is no guarantee that the framebuffer contains a valid image when
unblank is called. When using manual update displays it is the
responsibility of the user space to update the display, and so it should
be in this case also.
This patch removes the implicit display update on unblank.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
[tomi.valkeinen@ti.com: improved description]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Errors from the panel driver were ignored during panel initialization.
Handle the errors and fail accordingly.
Also move the display initialization to a separate function to make it
cleaner.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add get_dimensions() to struct omap_dss_driver. Use the call, if supported
by the driver, in OMAPFB.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
VENC code had 50ms sleep after enabling the output and 100ms sleep after
disabling the output. I don't see any reason for these sleeps.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
There's a 20ms sleep after VENC reset. It's unknown what bug this
circumvents and on what platforms. Add a Kconfig option to disable the
sleep.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
For some unknown reason we may get SYNC_LOST errors from the display
subsystem at initialization time if we don't sleep before resetting the
DSS. See the source (dss.c) for more comments.
However, 50ms is quite long time to sleep, and with some configurations
the SYNC_LOST may never happen, so this patch creates a Kconfig option
to disable the sleep.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The sleep workaround for the problem described in the comment doesn't
really work. This patch removes the workaround, and improves the comment
about the bug, and proposes an userspace workaround.
omap_dss_set_manager() is called 6 times when loading omapdss and
omapfb, which means that 40ms * 6 = 240ms was spent sleeping when
booting up.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Clock configuration was defined inside dssdev.phy.dsi struct. The clock
config doesn't really belong there, and so it's moved to dssdev.clock
struct.
Now the explicit clock configuration could also be used for other
interfaces than DSI, although there's no support for it currently.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The DSI protocol engine has no interrupt for signalling the end of a Frame
transfer. The present approach is to send a BTA after DISPC generates a
FRAMEDONE interrupt, and unlock the dsi bus only when the BTA Ack is received.
The assumption made with this approach was that OMAP will send a BTA only after
the long packet corresponding to the last line is sent. However, it is possible
that on the DISPC FRAMEDONE interrupt there are 2 (or more) lines of pixel data
in the DSI line buffer. Hence, the BTA Ack could be received for the long packet
corresponding to the second last line (or the third last and so on..).
Therefore, the current method doesn't ensure that the complete frame data is
sent before we start a new transfer. A similar explanation holds valid if we
send a BTA in between multiple short/long command packets from the slave port.
Introduce dsi_sync_vc functions, based on Tomi Valkeinen's idea, which ensure
that the DSI Virtual Channel in use(update_channel) completes its previous work
before proceeding to the next Frame/Command.
For a frame update, the DSI driver now sends a callback to the Panel Driver
on the FRAMEDONE interrupt itself. The callback in the panel driver then unlocks
the bus. dsi_sync_vc() functions are placed in dsi_vc_config_l4() and
dsi_vc_config_vp() to ensure that the previous task of the Virtual Channel is
completed.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The following changes have changed from OMAP3 to OMAP4 DSI:
-The register field DSI_PLL_FREQSEL in DSI_PLL_CONFIGURATION2 has been removed.
-DCS_CMD_ENABLE and DCS_CMD_CODE bits have been moved from DSI_CTRL to
DSI_VC_CTRLi, hence the control of the bits is available per VC.
-DSI LDO powergood notification doesn't work on OMAP4. This is mentioned in
OMAP4 errata revision 1.8(Errata 1.76).
-OCP_WIDTH register field is included in DSI_VC_CTRL.
-The SCP clock is also required to access DSI PLL registers
Introduce dss features for these changes so that DSI runs on both OMAP3 and
OMAP4.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
OMAP3630 has a HW bug causing DSI PLL power command POWER_ON_DIV (0x3)
to not work properly. The bug prevents us from enabling DSI PLL power
only to HS divider block.
This patch adds a dss feature for the bug and converts POWER_ON_DIV
requests to POWER_ON_ALL (0x2).
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dss.lcd_clk_source is set to the default value DSS_CLK_SRC_FCK at dss_init.
For OMAP2 and OMAP3, the dss.lcd_clk_source should always be the same as
dss.dispc_clk_source. The function dss_get_lcd_clk_source() always returns the
default value DSS_CLK_SRC_FCK for OMAP2/3. This leads to wrong clock dumps when
dispc_clk_source is not DSS_CLK_SRC_FCK.
Correct this function to always return dss.dispc_clk_source for OMAP2/3.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
On OMAP4, reading DSI_PLL_CONFIGURATION2 register requires the L3 clock
(CIO_CLK_ICG) to PLL. Currently dsi_dump_clocks() tries to read that
register without enabling the L3 clock, leading to crash if DSI is not
in use.
The status of the bit being read from DSI_PLL_CONFIGURATION2 is
available from dsi_clock_info->use_sys_clk, so we can avoid the whole
problem by just using that.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
use_sys_clk and highfreq fields in dsi.current_cinfo were never set.
Luckily they weren't used anywhere so it didn't cause any problems.
This patch fixes those fields and they are now set at the same time as
the rest of the fields.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
arch/arm/plat-omap/include/plat/nokia-dsi-panel.h is an include for the
OMAP DSS panel driver for Nokia's DSI displays. A more logical place for
it is in include/video.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
arch/arm/plat-omap/include/plat/panel-generic-dpi.h is an include for
the OMAP DSS panel driver for generic DPI displays. A more logical place
for it is in include/video.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
arch/arm/plat-omap/include/plat/display.h is an include for the OMAP DSS
driver. A more logical place for it is in include/video.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Currently, a long set of viafb options are needed to get the XO-1.5
laptop to output video (there is only 1 configuration that works, that
can't really be autodetected).
This patch automatically detects and configures viafb for the XO-1.5
laptop, meaning all that is required for working display is that
viafb is loaded.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
WARNING: drivers/video/built-in.o(.devinit.text+0x38): Section mismatch in reference from the function acornfb_probe() to the function .init.text:acornfb_setup()
The function __devinit acornfb_probe() references
a function __init acornfb_setup().
If acornfb_setup is only used by acornfb_probe then
annotate acornfb_setup with a matching annotation.
WARNING: drivers/video/built-in.o(.devinit.text+0x3c): Section mismatch in reference from the function acornfb_probe() to the function .init.text:acornfb_init_fbinfo()
The function __devinit acornfb_probe() references
a function __init acornfb_init_fbinfo().
If acornfb_init_fbinfo is only used by acornfb_probe then
annotate acornfb_init_fbinfo with a matching annotation.
WARNING: drivers/video/built-in.o(.devinit.text+0x4c0): Section mismatch in reference from the function acornfb_probe() to the (unknown reference) .init.data:(unknown)
The function __devinit acornfb_probe() references
a (unknown reference) __initdata (unknown).
If (unknown) is only used by acornfb_probe then
annotate (unknown) with a matching annotation.
WARNING: drivers/video/built-in.o(.devinit.text+0x4c8): Section mismatch in reference from the function acornfb_probe() to the (unknown reference) .init.data:(unknown)
The function __devinit acornfb_probe() references
a (unknown reference) __initdata (unknown).
If (unknown) is only used by acornfb_probe then
annotate (unknown) with a matching annotation.
WARNING: drivers/video/built-in.o(.devinit.text+0x4cc): Section mismatch in reference from the function acornfb_probe() to the (unknown reference) .init.data:(unknown)
The function __devinit acornfb_probe() references
a (unknown reference) __initdata (unknown).
If (unknown) is only used by acornfb_probe then
annotate (unknown) with a matching annotation.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The current code might result in trying to remap 512MB video ram on
a 32 bit system which is quite likely to fail.
This patch tries to map less of it down to 8MB as this should still
be enough to get a reasonably well working framebuffer. This should
make viafb work for many people without requiring them to manually
allocate more space.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch adds a config option to be compatible with X servers like
OpenChrome. This is required as for example the X server does not
handle things like disabled IGAs/PLLs resulting in a potential
freeze on X startup. With this option disabled we can provide some
nice features like power management and not reinitializing the
hardware on every mode switch (taking long time, causing flickering).
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
When allowing some PLL calculation we get a frequency that seems to
be a bit higher than what the OLPC DCON likes resulting in a still
readable but not so good image. We don't really know whether this is
a problem with the calculation formula or the OLPC but as other
displays seem to be happy with the other modes adjusting the OLPC
refresh looks like the better thing. This patch prevents a
regression when dynamic PLL calculation is allowed.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch fixes the devices connected on OLPC. The OLPC panel seems
to be connected to DVP1 and LVDS2 for some reasons and if not both
are handled correct the display does not work correct or not at all.
This patch prevents regressions on the OLPC where it worked by
accident but would break in future as the driver did not know the
correct devices connected. This might also fix hardware scaling.
Hopefully the OLPC is the only device with such a requirement but it
will be certainly better to actually know what devices are actually
connected and to not work by accident.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
drivers/video/s3fb.c: In function 's3_pci_remove':
drivers/video/s3fb.c:1388: error: 'par' undeclared (first use in this function)
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add I2C support for the DDC bus and also default mode initialization by
reading monitor EDID to the s3fb driver.
Tested on Trio64V+ (2 cards), Trio64V2/DX, Virge (3 cards),
Virge/DX (3 cards), Virge/GX2, Trio3D/2X (4 cards), Trio3D.
Will probably not work on Trio32 - my 2 cards have DDC support in BIOS that
looks different from the other cards but the DDC pins on the VGA connector
are not connected.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch fixes a regression introduced by
fd3cc69848b7e1873e5f12bbcdd572b20277ecf3a
"viafb: remove duplicated clock storage"
caused by an incosistent mode which pretended to have a higher
refresh rate than it actually had. The wrong refresh rate resulted
in a calculated higher pixclock which the OLPC DCON could not handle.
By reducing the refresh rate to 50Hz we get close to the old
pixclock which makes the OLPC display usable again.
Minor other adjustments are needed as 60Hz is assumed to be a safe
value which is not true for OLPC DCON. This is no problem as we only
support 1200x900 on the OLPC.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Reported-by: Daniel Drake <dsd@laptop.org>
OMAP3630 has a HW bug causing DSI PLL power command POWER_ON_DIV (0x3)
to not work properly. The bug prevents us from enabling DSI PLL power
only to HS divider block.
This patch adds a dss feature for the bug and converts POWER_ON_DIV
requests to POWER_ON_ALL (0x2).
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dss.lcd_clk_source is set to the default value DSS_CLK_SRC_FCK at dss_init.
For OMAP2 and OMAP3, the dss.lcd_clk_source should always be the same as
dss.dispc_clk_source. The function dss_get_lcd_clk_source() always returns the
default value DSS_CLK_SRC_FCK for OMAP2/3. This leads to wrong clock dumps when
dispc_clk_source is not DSS_CLK_SRC_FCK.
Correct this function to always return dss.dispc_clk_source for OMAP2/3.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
On OMAP4, reading DSI_PLL_CONFIGURATION2 register requires the L3 clock
(CIO_CLK_ICG) to PLL. Currently dsi_dump_clocks() tries to read that
register without enabling the L3 clock, leading to crash if DSI is not
in use.
The status of the bit being read from DSI_PLL_CONFIGURATION2 is
available from dsi_clock_info->use_sys_clk, so we can avoid the whole
problem by just using that.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
use_sys_clk and highfreq fields in dsi.current_cinfo were never set.
Luckily they weren't used anywhere so it didn't cause any problems.
This patch fixes those fields and they are now set at the same time as
the rest of the fields.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In case CONFIG_FB_PXA_OVERLAY is not defined, the pxafb_freq_transition()
function tests nonexistent member of pxafb_info (since the member is not
part of the structure).
Fix this by wraping the test in ifdef, even if I don't really like how the code
looks now. The check doesn't have to happen if overlays are disabled at all as
the check is always true then.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The spinlock is added to interrupt routine to ensure that the driver
is protected against multiple accesses.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'fbdev-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/fbdev-2.6:
efifb: Add override for 11" Macbook Air 3,1
efifb: Support overriding fields FW tells us with the DMI data.
fb: Reduce priority of resource conflict message
savagefb: Remove obsolete else clause in savage_setup_i2c_bus
savagefb: Set up I2C based on chip family instead of card id
savagefb: Replace magic register address with define
drivers/video/bfin-lq035q1-fb.c: introduce missing kfree
video: s3c-fb: fix checkpatch errors and warning
efifb: support AMD Radeon HD 6490
s3fb: fix Virge/GX2
fbcon: Remove unused 'display *p' variable from fb_flashcursor()
fbdev: sh_mobile_lcdcfb: fix module lock acquisition
fbdev: sh_mobile_lcdcfb: add blanking support
viafb: initialize margins correct
viafb: refresh rate bug collection
sh: mach-ap325rxa: move backlight control code
sh: mach-ecovec24: support for main lcd backlight
The 11" Macbook Air appears to claim that its stride is 1366, when it's
actually 2048. Override it.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Peter Jones <pjones@redhat.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Some machines apparently give us bogus linelength/stride/pitch data, so
we need to support letting the DMI table override the supplied data.
I bet you can't guess whose machines I'm talking about.
Signed-off-by: Peter Jones <pjones@redhat.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
It's expected that efifb will conflict with a native driver, so the
handover message should be informational rather than an error.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The else clause was not needed after the cleanup in commit
b8901b091d
Signed-off-by: Tormod Volden <debian.tormod@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
In practice this means enabling I2C (for DDC2) on all prosavage cards,
like the xorg ddx does. The savage4 and savage2000 families have only
one member each, so there is no change for those.
Tested on TwisterK.
Signed-off-by: Tormod Volden <debian.tormod@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Error handling code following a kmalloc should free the allocated data.
The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,f1,l;
position p1,p2;
expression *ptr != NULL;
@@
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
when != if (...) { <+...x...+> }
(
x->f1 = E
|
(x->f1 == NULL || ...)
|
f(...,x->f1,...)
)
...>
(
return \(0\|<+...x...+>\|ptr\);
|
return@p2 ...;
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch fixes the checkpatch errors listed below:
ERROR: space required before the open parenthesis '('
ERROR: need consistent spacing around '+' (ctx:WxV)
ERROR: space prohibited before that close parenthesis ')'
Also, following warning is fixed by adding 'platid' variable
which can reduce number of lines exceeding 80 characters.
WARNING: line over 80 characters
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* 'unicore32' of git://git.kernel.org/pub/scm/linux/kernel/git/epip/linux-2.6-unicore32:
unicore32 framebuffer fix: get videomemory by __get_free_pages() and make it floatable
unicore32 core architecture: remove duplicated #include
unicore32 rtc driver fix: cleanup irq_set_freq and irq_set_state
unicore32 fix: remove arch-specific futex support
unicore32 ldscript fix: add cacheline parameter to PERCPU() macro
We do this also in the real program code so there is no reason to
do it here too (and here it's hardly readable).
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch enables the framebuffer for the AMD Radeon 6490 found in the new MacBook Pro 8,2 generation.
The framebuffer's base is located at 0x90010000, the method for obtaining it was found in the same way mentioned in https://patchwork.kernel.org/patch/91704/
Signed-off-by: Davidlohr Bueso <dave@gnu.org>
Signed-off-by: Jonathan Gonzalez <zeus@gnu.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix Virge/GX2 support in s3fb:
- fix IDs: 86C357 is GX2, 86C359 is GX2+, 86C356 probably does not exist
- add memory size detection
- drive it the same way as Trio3D/2X
The original IDs most likely came from S3 website which claims that:
- 356 is Virge/GX2 with ID=8A10, driver included in Windows 2K, XP
- 357 is Virge/GX2+ with ID=8A11, driver included in Windows ME
- 359 is Virge/GX2+ with ID=8A12, driver included in Windows ME
but:
- google search for 86C356 only reveals references to Trio3D (probably
because of a typo - Trio3D is 86C365)
- my card is clearly marked as 86C357, Virge/GX2 and has ID=8A10
- there is no driver for IDs 8A11 and 8A12 in Windows ME
- there is a driver for ID 8A10 in Windows ME that says it's GX2 (357)
Tested with #9 Reality 334 (86C357 Virge/GX2, ID=0x8A10).
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Whenever the LCDC is to be started or stopped, a board callback is
checked for existence and invoked. Prior to the invokation, the
callback's module lock is also acquired, to be released once the
callback returns. However, the order of testing makes it possible for
the lock to be acquired and not released in case the callback does not
exist. This patch reorders the tests to prevent this particular case.
Signed-off-by: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add a blanking callback to the LCDC driver in order to support both
FBIOBLANK and TIOCLINUX blanking ioctls. LCDC clocks are also released
if the requested blanking level is superior to FB_BLANK_NORMAL, to allow
runtime PM to disable the clocks if possible.
Signed-off-by: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
We do not need viafb_second{,_virtual}_{xres,yres} outside of
viafbdev.c so move them there and eliminate the virtual ones where
the only sane usage is done during initalization.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch moves all unprotected VGA initialization in one table and
provides some documentation for those values.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch adds support for enabling and configuring the engine on
VIAs IGPs. This is the main clock used for everything but pixel
output.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch introduces dummy functions to execute when we don't know
what we should do (due to missing documentation). They do nothing
but print a nice message in the log explaining the situation.
To trigger this message initial power management support is
activated which might save a bit energy by disabling PLL and clock
if no device is configured to use them.
Note: The message is only shown for the oldest IGPs CLE266 and K400
as for the other platforms there are reasonable assumptions
how it does (hopefully) work.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (442 commits)
[media] videobuf2-dma-contig: make cookie() return a pointer to dma_addr_t
[media] sh_mobile_ceu_camera: Do not call vb2's mem_ops directly
[media] V4L: soc-camera: explicitly require V4L2_BUF_TYPE_VIDEO_CAPTURE
[media] v4l: soc-camera: Store negotiated buffer settings
[media] rc: interim support for 32-bit NEC-ish scancodes
[media] mceusb: topseed 0x0011 needs gen3 init for tx to work
[media] lirc_zilog: error out if buffer read bytes != chunk size
[media] lirc: silence some compile warnings
[media] hdpvr: use same polling interval as other OS
[media] ir-kbd-i2c: pass device code w/key in hauppauge case
[media] rc/keymaps: Remove the obsolete rc-rc5-tv keymap
[media] remove the old RC_MAP_HAUPPAUGE_NEW RC map
[media] rc/keymaps: Rename Hauppauge table as rc-hauppauge
[media] rc-rc5-hauppauge-new: Fix Hauppauge Grey mapping
[media] rc-rc5-hauppauge-new: Add support for the old Black RC
[media] rc-rc5-hauppauge-new: Add the old control to the table
[media] rc-winfast: Fix the keycode tables
[media] a800: Fix a few wrong IR key assignments
[media] opera1: Use multimedia keys instead of an app-specific mapping
[media] dw2102: Use multimedia keys instead of an app-specific mapping
...
Fix up trivial conflicts (remove/modify and some real conflicts) in:
arch/arm/mach-omap2/devices.c
drivers/staging/Kconfig
drivers/staging/Makefile
drivers/staging/dabusb/dabusb.c
drivers/staging/dabusb/dabusb.h
drivers/staging/easycap/easycap_ioctl.c
drivers/staging/usbvideo/usbvideo.c
drivers/staging/usbvideo/vicam.c
This patch is a huge move operation with some rename and introduces
an interface to still use the functions. This should be a step in
the right direction to reuse the code whenever possible but cleanly
separate code that differs on different platform and keeping the
complexity as low as possible.
pll_config was renamed to via_pll_config to keep the naming scheme.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (35 commits)
ARM: Update (and cut down) mach-types
ARM: 6771/1: vexpress: add support for multiple core tiles
ARM: 6797/1: hw_breakpoint: Fix newlines in WARNings
ARM: 6751/1: vexpress: select applicable errata workarounds in Kconfig
ARM: 6753/1: omap4: Enable ARM local timers with OMAP4430 es1.0 exception
ARM: 6759/1: smp: Select local timers vs broadcast timer support runtime
ARM: pgtable: add pud-level code
ARM: 6673/1: LPAE: use phys_addr_t instead of unsigned long for start of membanks
ARM: Use long long format when printing meminfo physical addresses
ARM: integrator: add Integrator/CP sched_clock support
ARM: realview/vexpress: consolidate SMP bringup code
ARM: realview/vexpress: consolidate localtimer support
ARM: integrator/versatile: consolidate FPGA IRQ handling code
ARM: rationalize versatile family Kconfig/Makefile
ARM: realview: remove old AMBA device DMA definitions
ARM: versatile: remove old AMBA device DMA definitions
ARM: vexpress: use new init_early for clock tree and sched_clock init
ARM: realview: use new init_early for clock tree and sched_clock init
ARM: versatile: use new init_early for clock tree and sched_clock init
ARM: integrator: use new init_early for clock tree init
...
This patch adds functions to enable/disable the display clocks.
It also fixes a tiny bug that slipped in with a previous commit but
could not yet have caused any problems.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch adds some support for clock source selection as well as
PLL power management. The code is unused at the moment but was
successfully tested as far as possible.
The implementation is according to the documentation for VX700,
VX800, VX855, VX900. Probably the source selection works like this
starting with K800 and the power managemennt at least since VX700.
(guessed based on the initialization in viamode.c)
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
As no caller is interested in the result call viafb_get_clk_value
directly from viafb_set_vclock to encapsulate the hardware dependend
stuff there.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch removes the max_hres and max_vres which are not used at
the moment. In general they could be useful but it would be better
to get them via any standard EDID implementation and not the buggy
incomplete one currently used which is also removed as far as
possible.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch allows calculating the pll multiplier within limits based
on the previous table. All available information supports that it
should be possible/sane to choose the multiplier free within some
ranges.
Storing the multiplier ranges instead of lots of pll configurations
reduces the memory needed and may as well improve the performance.
It is also expected to provide better pll values resulting in better
frequencies for the connected devices.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Copy 88pm860x platform data into different mfd_data structure for
backlight driver. So move the identification of device node from
backlight driver to mfd driver.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This silences warnings such as
drivers/video/tmiofb.c: In function 'tmiofb_hw_init':
drivers/video/tmiofb.c:270: warning: initialization discards qualifiers from pointer target type
These were added by me in commit 2a79bb1d.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Use mfd_data for passing information from mfd drivers to mfd
clients. The mfd_cell's driver_data field is being phased out.
Clients that were using driver_data now access .mfd_data
via mfd_get_data(). This changes tmio-fb only; mfd drivers with
other cells are not modified.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
No need to explicitly set the cell's platform_data/data_size.
Modify clients to use mfd_get_cell helper function instead of
accessing platform_data directly.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
1. simple_strto*() do not contain overflow checks and crufty,
libc way to indicate failure.
2. strict_strto*() also do not have overflow checks but the name and
comments pretend they do.
3. Both families have only "long long" and "long" variants,
but users want strtou8()
4. Both "simple" and "strict" prefixes are wrong:
Simple doesn't exactly say what's so simple, strict should not exist
because conversion should be strict by default.
The solution is to use "k" prefix and add convertors for more types.
Enter
kstrtoull()
kstrtoll()
kstrtoul()
kstrtol()
kstrtouint()
kstrtoint()
kstrtou64()
kstrtos64()
kstrtou32()
kstrtos32()
kstrtou16()
kstrtos16()
kstrtou8()
kstrtos8()
Include runtime testsuite (somewhat incomplete) as well.
strict_strto*() become deprecated, stubbed to kstrto*() and
eventually will be removed altogether.
Use kstrto*() in code today!
Note: on some archs _kstrtoul() and _kstrtol() are left in tree, even if
they'll be unused at runtime. This is temporarily solution,
because I don't want to hardcode list of archs where these
functions aren't needed. Current solution with sizeof() and
__alignof__ at least always works.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In systems with multiple framebuffer devices, one of the devices might be
blanked while another is unblanked. In order for the backlight blanking
logic to know whether to turn off the backlight for a particular
framebuffer's blanking notification, it needs to be able to check if a
given framebuffer device corresponds to the backlight.
This plumbs the check_fb hook from core backlight through the
pwm_backlight helper to allow platform code to plug in a check_fb hook.
Signed-off-by: Robert Morell <rmorell@nvidia.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Arun Murthy <arun.murthy@stericsson.com>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The following symbols are needlessly defined global: jornada_bl_init,
jornada_bl_exit, jornada_lcd_init, jornada_lcd_exit.
Make them static.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
apple_bl uses ACPI interfaces (data & code), so it should depend on ACPI.
drivers/video/backlight/apple_bl.c:142: warning: 'struct acpi_device' declared inside parameter list
drivers/video/backlight/apple_bl.c:142: warning: its scope is only this definition or declaration, which is probably not what you want
drivers/video/backlight/apple_bl.c:201: warning: 'struct acpi_device' declared inside parameter list
drivers/video/backlight/apple_bl.c:215: error: variable 'apple_bl_driver' has initializer but incomplete type
drivers/video/backlight/apple_bl.c:216: error: unknown field 'name' specified in initializer
...
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Matthew Garrett <mjg@redhat.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It works on hardware other than Macbook Pros, and it works on GPUs other
than Nvidia. It should even work on iMacs, so change the name to match
reality more precisely and include an alias so existing users don't get
confused.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Richard Purdie <richard.purdie@linuxfoundation.org>
Cc: Mourad De Clerck <mourad@aquazul.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The SMI-based backlight control functionality may fail to work if the
system is running under EFI rather than BIOS. Check that the hardware
responds as expected, and exit if it doesn't.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Richard Purdie <richard.purdie@linuxfoundation.org>
Cc: Mourad De Clerck <mourad@aquazul.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This driver only has to deal with two different classes of hardware, but
right now it needs new DMI entries for every new machine. It turns out
that there's an ACPI device that uniquely identifies Apples with backlights,
so this patch reworks the driver into an ACPI one, identifies the hardware
by checking the PCI vendor of the root bridge and strips out all the DMI
code. It also changes the config text to clarify that it works on devices
other than Macbook Pros and GPUs other than nvidia.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Richard Purdie <richard.purdie@linuxfoundation.org>
Cc: Mourad De Clerck <mourad@aquazul.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There may be multiple ways of controlling the backlight on a given
machine. Allow drivers to expose the type of interface they are
providing, making it possible for userspace to make appropriate policy
decisions.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: David Airlie <airlied@linux.ie>
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Situation as follow:
2 GPUs + vesafb + kms.
GPU 1 is primary, vesafb binds to it as fb0
radeon loads
GPU 0 loads as fb1
GPU 1 loads, vesafb gets kicked off which causes fb0 to unbind
console, which causes the dummy console to rebind.
this means fbcon_deinit gets called, which calls fbcon_exit
since the console isn't bound anymore and we set fbcon_has_exited.
GPU 1 creates a new fb0 which is primary and we want to be console.
fbcon_fb_registered gets called sets the primary up and calls set_con2fb_map,
however as fbcon_has_exited is set nothing further ever happens.
This patch bypasses the fbcon_has_exited and checks if the console is unbound,
if its unbound it calls the fbcon_takeover which calls the vt layer to
call the fbcon_startup method and everthing works.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
- add commandline options:
sm501fb.mode:
Specify resolution as "<xres>x<yres>[-<bpp>][@<refresh>]"
sm501fb.bpp:
Specify bit-per-pixel if not specified mode
- Add support for encoding display mode information
in the device tree using verbatim EDID block.
If the "edid" entry in the "smi,sm501" node is present,
the driver will build mode database using EDID data
and allow setting the display modes from this database.
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: linux-fbdev@vger.kernel.org
cc: devicetree-discuss@ozlabs.org
cc: Ben Dooks <ben@simtec.co.uk>
cc: Vincent Sanders <vince@simtec.co.uk>
cc: Samuel Ortiz <sameo@linux.intel.com>
cc: linux-kernel@vger.kernel.org
cc: Randy Dunlap <rdunlap@xenotime.net>
cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
- add read/write functions for using this driver
also on powerpc plattforms
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: linux-fbdev@vger.kernel.org
cc: devicetree-discuss@ozlabs.org
cc: Ben Dooks <ben@simtec.co.uk>
cc: Vincent Sanders <vince@simtec.co.uk>
cc: Samuel Ortiz <sameo@linux.intel.com>
cc: linux-kernel@vger.kernel.org
cc: Randy Dunlap <rdunlap@xenotime.net>
cc: Paul Mundt <lethal@linux-sh.org>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The macros for getting the values for horizontal sync width and offset
do not respect the EDID specification. Both these values are 10 bit
values according to [1], not 6 bit values. The lower 8 bits are stored
in byte 8 and byte 9 of the DTD respectively, while two additional bits
for each value are stored in byte 11. The original macros just slammed
the bits together.
Although the original macros usually worked fine because the higher two
bits are rarely used, it can cause severe problems on plasma panels
running at 1920x1080 @ 50 Hz with drivers that rely on the correct
parsing of the EDID data by fbmon.c (e.g. udlfb).
The patch should apply cleanly to both the fbdev-2.6.git branch and
linux-next.git branch.
[1] VESA Enhanced Extended Display Identification Data Standard,
Release A, Revision 2, page 34, notes 7 & 8, VESA, Sep 2006
Signed-off-by: Martin Decky <martin@decky.cz>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Use mask 0x10 for "soft cursor" detection on in function tile_cursor.
(Tile Blitting Operation in framebuffer console).
The old mask 0x01 for vc_cursor_type detects CUR_NONE, CUR_LOWER_THIRD
and every second mode value as "software cursor". This hides the cursor
for these modes (cursor.mode = 0). But, only CUR_NONE or "software cursor"
should hide the cursor.
See also 0x10 in functions add_softcursor, bit_cursor and cw_cursor.
Signed-off-by: Henry Nestler <henry.nestler@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch fixes a memory leak in the error path.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
metronomefb_remove is marked __devexit,
thus add __devexit_p around reference to metronomefb_remove.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
hecubafb_remove is marked __devexit,
thus add __devexit_p around reference to hecubafb_remove.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The below patch fixes a typo occationally to occasionally.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch introduces lcdc->lcdcon_pol_negative which set CONTRAST_CTR
register to inverted polarity.
Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Return PTR_ERR(sfb->bus_clk) instead of 0 if clk_get fails.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
with an PAT-enabled kernel, when using uvesafb or vesafb, these drivers will
create uncached-minus PAT entries for the framebuffer memory because they use
ioremap() (not the *_cache or *_wc variants). When the framebuffer memory
intersects with the video RAM used by Xorg, the complete video RAM will be
mapped uncached-minus what results in a serve performance penalty.
Here are the correct MTRR entries created by uvesafb:
schlicht@netbook:~$ cat /proc/mtrr
reg00: base=0x000000000 ( 0MB), size= 2048MB, count=1: write-back
reg01: base=0x06ff00000 ( 1791MB), size= 1MB, count=1: uncachable
reg02: base=0x070000000 ( 1792MB), size= 256MB, count=1: uncachable
reg03: base=0x0d0000000 ( 3328MB), size= 16MB, count=1: write-combining
And here are the problematic PAT entries:
schlicht@netbook:~$ sudo cat /sys/kernel/debug/x86/pat_memtype_list
PAT memtype list:
write-back @ 0x0-0x1000
uncached-minus @ 0x6fedd000-0x6fee3000
uncached-minus @ 0x6fee2000-0x6fee3000
uncached-minus @ 0x6fee2000-0x6fee3000
uncached-minus @ 0x6fee2000-0x6fee3000
uncached-minus @ 0x6fee2000-0x6fee3000
uncached-minus @ 0x6fee2000-0x6fee3000
uncached-minus @ 0x6fee2000-0x6fee3000
uncached-minus @ 0x6fee2000-0x6fee3000
uncached-minus @ 0x6fee3000-0x6fee4000
uncached-minus @ 0x6fee3000-0x6fee4000
uncached-minus @ 0x6fee3000-0x6fee4000
uncached-minus @ 0xd0000000-0xe0000000 <-- created by xserver-xorg
uncached-minus @ 0xd0000000-0xd1194000 <-- created by uvesafb
uncached-minus @ 0xf4000000-0xf4009000
uncached-minus @ 0xf4200000-0xf4400000
uncached-minus @ 0xf5000000-0xf5010000
uncached-minus @ 0xf5100000-0xf5104000
uncached-minus @ 0xf5400000-0xf5404000
uncached-minus @ 0xf5404000-0xf5405000
uncached-minus @ 0xf5404000-0xf5405000
uncached-minus @ 0xfed00000-0xfed01000
Therefore I created the attached patch for uvesafb which uses ioremap_wc() to
create the correct PAT entries, as shown below:
schlicht@netbook:~$ sudo cat /sys/kernel/debug/x86/pat_memtype_list
PAT memtype list:
write-back @ 0x0-0x1000
uncached-minus @ 0x6fedd000-0x6fee3000
uncached-minus @ 0x6fee2000-0x6fee3000
uncached-minus @ 0x6fee2000-0x6fee3000
uncached-minus @ 0x6fee2000-0x6fee3000
uncached-minus @ 0x6fee2000-0x6fee3000
uncached-minus @ 0x6fee2000-0x6fee3000
uncached-minus @ 0x6fee2000-0x6fee3000
uncached-minus @ 0x6fee2000-0x6fee3000
uncached-minus @ 0x6fee3000-0x6fee4000
uncached-minus @ 0x6fee3000-0x6fee4000
uncached-minus @ 0x6fee3000-0x6fee4000
write-combining @ 0xd0000000-0xe0000000
write-combining @ 0xd0000000-0xd1194000
uncached-minus @ 0xf4000000-0xf4009000
uncached-minus @ 0xf4200000-0xf4400000
uncached-minus @ 0xf5000000-0xf5010000
uncached-minus @ 0xf5100000-0xf5104000
uncached-minus @ 0xf5400000-0xf5404000
uncached-minus @ 0xf5404000-0xf5405000
uncached-minus @ 0xf5404000-0xf5405000
uncached-minus @ 0xfed00000-0xfed01000
This results in a performance gain, objectively measurable with e.g.
x11perf -comppixwin10 -comppixwin100 -comppixwin500:
1: x11perf_xaa.log
2: x11perf_xaa_patched.log
1 2 Operation
-------- ---------------- -----------------
124000.0 202000.0 ( 1.63) Composite 10x10 from pixmap to window
3340.0 24400.0 ( 7.31) Composite 100x100 from pixmap to window
131.0 1150.0 ( 8.78) Composite 500x500 from pixmap to window
You can see the serve performance gain when composing larger pixmaps to window.
The patches replace the ioremap() function with the variant matching the mtrr-
parameter. To create "write-back" PAT entries, the ioremap_cache() function
must be called after creating the MTRR entries, and the ioremap_cache() region
must completely fit into the MTRR region, this is why the MTRR region size is
now rounded up to the next power-of-two.
Signed-off-by: Thomas Schlichter <thomas.schlichter@web.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Current implementation calls of_iounmap for par->fbc twice in error path.
In the case of goto out_unmap_dac, we should call of_iounmap for par->dac.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Some Radeon cards have an I2C-based thermal sensor chip connected to
the "monid" I2C bus. Set the I2C probing class of this bus properly so
that hwmon drivers can detect devices on it and bind to them.
This closes kernel.org bug #26172.
We exclude PPC for the time being, as Benjamin doesn't want us to
mess up with them without explicit testing, and there is no evidence
that this change is needed for them either.
Reported-by: Alexander Goomenyuk <emerg.reanimator@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
backlight_device_register() returns an ERR_PTR. It doesn't return NULL.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The size calculation is done incorrectly in request_mem_region because
it should include both the start and end (end - start + 1).
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The size calculation is done incorrectly here because it should include
both the start and end (end - start + 1).
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Use "new" start address register 0x69 (bits 16-20) instead of "old" 0x31
(bits 16-17) and 0x51 (bits 18-19). This is needed for panning to work
correctly on Trio3D/2X cards (and does no harm on other ones).
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Ondrej Zajicek <santiago@crfreenet.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Enable Data Transfer Position Control (DTPC). This is needed at least on
Virge/DX to correctly display at higher pixclocks.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Ondrej Zajicek <santiago@crfreenet.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Enable pixel multiplexing in 15/16bpp modes when pixclock is over 115MHz
on Trio3D (86C365) cards to fix artifacts on the left side of screen.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Ondrej Zajicek <santiago@crfreenet.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add support for S3 Trio3D (86C365) cards to s3fb driver. Tested with one 4MB card.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Ondrej Zajicek <santiago@crfreenet.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Maximize virtual vertical framebuffer size during init to allow fast scrolling
(accelerated by panning).
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Ondrej Zajicek <santiago@crfreenet.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This allows the driver to work in multi-domain PCI
configurations.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This allows the driver to work in multi-domain PCI
configurations.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This allows the driver to work in multi-domain PCI
configurations.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add support for ZGI Z9 DDR2 POST. The init sequence is from XGI's
xgifb driver.
Tested with ARM board using a PCI card with XGI Z9s and 32 MB DDR2
memory. After a cold reset the POST succeeds.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Move DDR2 register setting code into separate subroutines. No changes
in functionality.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Detect the XGI Z9 RAM type as "documented" by the XGI's xgifb driver.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Z7 and Z9 have the same PCI ID, so additional checking is needed to
detect Z9. The method was "documented" in XGI's xgifb driver.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Move XGI POST RAM type detection into a separate subroutine to make
further code changes easier. No changes in functionality
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Currently there is no indication if R/W test fails during POST. This can
happen e.g. when user plugs in a card with unsupported type of memory.
Since the driver will be unusable, it's better to fail the whole POST
if the memory cannot be configured properly.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Kirill A. Shutemov <kirill@shutemov.name>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Those ioctls were produced by the wrong arguments for _IO macros,
and were replaced by fixed versions on an early 2.6 kernel.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove incorrect Matrox G200eV support that was previously added by
commit e3a1938805
A serious issue with the incorrect G200eV support that reproduces on the
Matrox G200eV equipped IBM x3650 M2 is the total lack of text (login
banner, login prompt, etc) on the console when X is not running and
total lack of text on all of the virtual consoles after X is started.
Any concerns that the incorrect code (upstream since October 2008) has
been successfully used on non-IBM G200eV equipped system(s) appear to be
unwarranted. In addition to the serious/non-intermittent nature of
issues that have been spotted on IBM systems, complete removal of the
incorrect code is clearly supported by the following Matrox (Yannick
Heneault) provided input:
"It impossible that this patch should have work on a system.
The patch only declare the G200eV as a regular G200 which is
not case. Many registers are different, including at least the
PLL programming sequence. If the G200eV is programmed like a
regular G200, it will not display anything."
v1 - Initial patch that removed the incorrect code for _all_
G200eV equipped systems.
v2 - Darrick Wong provided patch that blacklisted the incorrect
code on G200eV equipped IBM systems leaving it enabled on
all G200eV equipped non-IBM systems.
v3 - Same code changes included with v1 plus additional
justification for complete removal of the incorrect code.
Signed-off-by: Gary Hade <garyhade@us.ibm.com>
Cc: Darrick J. Wong <djwong@us.ibm.com>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Petr Vandrovec <vandrove@vc.cvut.cz>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Yannick Heneault <yannick_heneault@matrox.com>
Cc: Christian Toutant <ctoutant@matrox.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As the iga path is the only remaining information which is also
handled by the active devices there is no reason to keep it.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Later the correct values will be written so there is no need to
write early some values which might be wrong.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This moves some mode independend initialization code to the function
where the other parts of the initialization are.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch initializes the margins for the initial mode correct.
This is required to get the desired initial refresh rate. Also do
more verbose sanity checking to prevent misbehavior.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
* 'trivial' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6: (25 commits)
video: change to new flag variable
scsi: change to new flag variable
rtc: change to new flag variable
rapidio: change to new flag variable
pps: change to new flag variable
net: change to new flag variable
misc: change to new flag variable
message: change to new flag variable
memstick: change to new flag variable
isdn: change to new flag variable
ieee802154: change to new flag variable
ide: change to new flag variable
hwmon: change to new flag variable
dma: change to new flag variable
char: change to new flag variable
fs: change to new flag variable
xtensa: change to new flag variable
um: change to new flag variables
s390: change to new flag variable
mips: change to new flag variable
...
Fix up trivial conflict in drivers/hwmon/Makefile
Add dss.dpll4_m4_ck (DSS FCLK) initialization for OMAP4. This is used
to compute the pixel clock for DPI interface and also to reconfigure
the DSS FCLK to the desired rate, corresponding to the rate computed
for pixel clock.
Adding these cpu_is_44xx() checks are meant to be temporary, until a
cleaner implementation to manage these checks are added. Currently this
is needed to get DVI display running on OMAP4 PandaBoard
Signed-off-by: Raghuveer Murthy <raghuveer.murthy@ti.com>
[tomi.valkeinen@ti.com: minor changes due to conflicts]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
OMAP2 does not have dpll4_m4_ck source clock for dss functional clock,
but later OMAPs do. Currently we check for cpu type in multiple places
to find out if dpll4_m4_ck is available.
This patch cleans up dss.c by using the fact that dss.dpll4_m4_ck
pointer is NULL on OMAP2. This allows us to remove many of the cpu
checks.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
* 'for-linus' of git://codeaurora.org/quic/kernel/davidb/linux-msm: (46 commits)
msm: scm: Check for interruption immediately
msm: scm: Fix improper register assignment
msm: scm: Mark inline asm as volatile
msm: iommu: Enable HTW L2 redirection on MSM8960
msm: iommu: Don't read from write-only registers
msm: iommu: Remove dependency on IDR
msm: iommu: Use ASID tagging instead of VMID tagging
msm: iommu: Rework clock logic and add IOMMU bus clock control
msm: iommu: Clock control for the IOMMU driver
msm: mdp: Set the correct pack pattern for XRGB/ARGB
msm_fb: Fix framebuffer console
msm: mdp: Add support for RGBX 8888 image format.
video: msmfb: Put the partial update magic value into the fix_screen struct.
msm: clock: Migrate to clkdev
msm: clock: Remove references to clk_ops_pcom
msm: headsmp.S: Fix section mismatch
msm: Use explicit GPLv2 licenses
msm: iommu: Enable IOMMU support for MSM8960
msm: iommu: Generalize platform data for multiple targets
msm: iommu: Create a Kconfig item for the IOMMU driver
...
* 'devel-stable' of master.kernel.org:/home/rmk/linux-2.6-arm: (289 commits)
davinci: DM644x EVM: register MUSB device earlier
davinci: add spi devices on tnetv107x evm
davinci: add ssp config for tnetv107x evm board
davinci: add tnetv107x ssp platform device
spi: add ti-ssp spi master driver
mfd: add driver for sequencer serial port
ARM: EXYNOS4: Implement Clock gating for System MMU
ARM: EXYNOS4: Enhancement of System MMU driver
ARM: EXYNOS4: Add support for gpio interrupts
ARM: S5P: Add function to register gpio interrupt bank data
ARM: S5P: Cleanup S5P gpio interrupt code
ARM: EXYNOS4: Add missing GPYx banks
ARM: S3C64XX: Fix section mismatch from cpufreq init
ARM: EXYNOS4: Add keypad device to the SMDKV310
ARM: EXYNOS4: Update clocks for keypad
ARM: EXYNOS4: Update keypad base address
ARM: EXYNOS4: Add keypad device helpers
ARM: EXYNOS4: Add support for SATA on ARMLEX4210
plat-nomadik: make GPIO interrupts work with cpuidle ApSleep
mach-u300: define a dummy filter function for coh901318
...
Fix up various conflicts in
- arch/arm/mach-exynos4/cpufreq.c
- arch/arm/mach-mxs/gpio.c
- drivers/net/Kconfig
- drivers/tty/serial/Kconfig
- drivers/tty/serial/Makefile
- drivers/usb/gadget/fsl_mxc_udc.c
- drivers/video/Kconfig
* 'defcfg' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6647/1: add Versatile Express defconfig
ARM: 6644/1: mach-ux500: update the U8500 defconfig
* 'drivers' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6764/1: pl011: factor out FIFO to TTY code
ARM: 6763/1: pl011: add optional RX DMA to PL011 v2
ARM: 6758/1: amba: support pm ops
ARM: amba: make amba_driver id_table const
ARM: amba: make internal ID table handling const
ARM: amba: make probe() functions take const id tables
ARM: 6662/1: amba: make amba_bustype non-static
ARM: mmci: add dmaengine-based DMA support
ARM: mmci: no need for separate host->data_xfered
ARM: mmci: avoid unnecessary switch to data available PIO interrupts
ARM: mmci: no need to call flush_dcache_page() with sg_miter API
ARM: mmci: avoid reporting too many completed bytes on fifo overrun
ALSA: AACI: make fifo variables more explanitory
ALSA: AACI: no need to call snd_pcm_period_elapsed() for each period
ALSA: AACI: use snd_pcm_lib_period_bytes()
ALSA: AACI: clean up AACI announcement printk
ALSA: AACI: fix channel mask selection
ALSA: AACI: fix number of channels for record
ALSA: AACI: fix multiple IRQ claiming
* 'cyberpro-next' of master.kernel.org:/home/rmk/linux-2.6-arm:
VIDEO: cyberpro: remove unused cyber2000fb_get_fb_var()
VIDEO: cyberpro: remove useless function extreg pointers
VIDEO: cyberpro: update handling of device structures
VIDEO: cyberpro: add support for video capture I2C
VIDEO: cyberpro: make 'reg_b0_lock' always present
VIDEO: cyberpro: add I2C support
VIDEO: cyberpro: select lowest multipler/divisor for PLL
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/epip/linux-2.6-unicore32: (40 commits)
unicore32: rewrite arch-specific tlb.h to use asm-generic version
unicore32: modify io_p2v and io_v2p macros, and adjust PKUNITY_mmio_BASEs
unicore32: replace unicore32-specific iomap functions with generic lib implementation
unicore32 machine related: add frame buffer driver for pkunity-v3 soc
unicore32 machine related files: add i2c bus drivers for pkunity-v3 soc
unicore32 io: redefine __REG(x) and re-use readl/writel funcs
unicore32 i8042 upgrade and bugfix: adjust resource request region type
unicore32 upgrade to v2.6.38-rc5: add one more paramter for pte_alloc_map call
unicore32 i8042: adjust io funcs of i8042-unicore32io.h
unicore32: rename PKUNITY_IOSPACE_BASE to PKUNITY_MMIO_BASE
unicore32: modify function names and parameters for irq_chips
unicore32: remove unused lines in arch/unicore32/include/asm/irq.h
unicore32 time.c: change calculate method for clock_event_device
unicore32: ADD MAINTAINER for unicore32 architecture
unicore32 machine related files: ps2 driver
unicore32 machine related files: pci bus handling
unicore32 machine related files: hardware registers
unicore32 machine related files: core files
unicore32 additional architecture files: boot process
unicore32 additional architecture files: low-level lib: misc
...
Acked-by: Arnd Bergmann <arnd@arndb.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/fbdev-2.6:
fbdev: sh_mobile_lcdc: Add YUV framebuffer support
viafb: split pll configs up
viafb: remove duplicated clock storage
viafb: always return the best possible clock
viafb: remove duplicated clock information
fbdev: sh_mobile_lcdcfb: add backlight support
viafb: factor lcd scaling parameters out
viafb: strip some structures
viafb: remove unused data_mode and device_type
viafb: kill lcd_panel_id
video via: make local variables static
video via: fix iomem access
video/via: drop deprecated (and unused) i2c_adapter.id
Replace EXTRA_CFLAGS with ccflags-y.
Signed-off-by: matt mooney <mfm@muteddisk.com>
Acked-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
change from original version -- by advice of Paul Mundt
1. remove videomemorysize definitions
2. remove unifb_enable and unifb_setup
3. use dev_warn instead of printk in fb driver
4. remove judgement for FB_ACCEL_PUV3_UNIGFX
5. adjust clk_get and clk_set_rate calls
6. add resources definitions
7. remove unifb_option
8. adjust register for platform_device
9. adjust unifb_ops position and unifb_regs assignment position
Signed-off-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
Acked-by: Arnd Bergmann <arnd@arndb.de>
This patch fixes multiple issues with the handling of refresh rates
especially for multi-display setups. If you experienced problems
with wrong refresh rates this patch might fix them.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
It's not safe to disable controller if overlay(s) is enabled (results in
system hang). So we avoid to disable controller in this case. Userspace
should choose proper governor to avoid freq changing when overlay is in
use, otherwise LCD may blink.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Sascha Hauer <s.hauer@pengutronix.de> pointed that
ypos takes value of xpos due to typo.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
pxafb_overlay_init is not right place to change Z-ordering,
move it to main plane initialization.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
PXAFB overlay memory management is something messy:
- it allocates memory dynamically on open/release, and it results
in memory allocation failure after ~1h of uptime (system does not have
115k of physically contiguous memory)
- in release callback it tries to free memory even if it was not
allocated.
Also driver touches FDADR1 on main plane reconfiguration, and it can cause
problems if overlay1 is enabled.
This patch attempts to fix those issues.
Patch is based on Russell King's work.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Supports YCbCr420sp, YCbCr422sp, and YCbCr44sp, formats
(bpp = 12, 16, and 24) respectively.
When double-buffering both Y planes appear before the C planes (Y-Y-C-C),
as opposed to Y-C-Y-C.
Set .nonstd in struct sh_mobile_lcdc_chan_cfg to enable YUV mode, and use
.bpp to distiguish between the 3 modes.
The value of .nonstd is copied to bits 16-31 of LDDFR in the LCDC and
should be set accordingly.
.nonstd must be set to 0 for RGB mode.
Due to the encoding of YUV data, the framebuffer will clear to green
instead of black.
In YUV 420 mode, panning is only possible in 2 line increments.
Additionally in YUV 420 mode the vertical resolution of the framebuffer
must be an even number.
Signed-off-by: Damian Hobson-Garcia <dhobsong@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
calling the platform registration of HDMI driver from core
during initialization.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Adding kconfig and makefile changes to add support for HDMI in OMAP4.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The panel driver(hdmi_omap4_panel.c) in omap2/dss acts as a controller
to manage the enable and disable requests and synchronize audio and video.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Adding the hdmi interface driver(hdmi.c) to the dss driver. It configures
the audio and video portion of HDMI based on functionality called by the
panel driver.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Yong Zhi <y-zhi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Adding the hdmi interface driver header file (hdmi.h) to the dss driver.
Register and structure declaration done here.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Adding function to reset/set gamma table bit for TV interface, currently
only support for disabled is added.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Adding function to select between HDMI or VENC clock source.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Adding display type HDMI in dss_features, overlay and the manager so that
HDMI type of display will be recognized.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
print_irq_status functions can be called with empty irq status when full
irq debugging is enabled. This patch makes print_irq_status functions
return immediately when given an empty irq status to lessen the debug
spam slightly.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dsi_vc_send_bta_sync() waits for BTA interrupt with a 500ms timeout. If
a DSI error happens, no BTA is received and the timeout triggers. This
could be handled much faster by listening to DSI errors also.
This patch uses the ISR support to notice DSI errors while waiting for
the BTA, thus speeding up the fail-path considerably.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add generic ISR support for DSI interrupts. ISRs can be used instead of
custom hooks in the interrupt handler.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Clean up the IRQ handler a bit by separating collection of IRQ stats and
handling of IRQ errors to separate functions.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The DSI PLL parameters (regm, regn, regm_dispc, regm_dsi, fint) have different
fields and also different Max values on OMAP3 and OMAP4. Use dss features to
calculate the register fields and min/max values based on current OMAP revision.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Create 2 functions dss_feat_get_param_min() and dss_feat_get_param_max() which
return the minimum and maximum value of a parameter. Introduce a enum in
dss_features called dss_range_param which contains parameters whose ranges we
are interested in.
Replace this with dss_feat_get_max_dss_fck() which is specific to the parameter
DSS_FCK.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The structures dss_reg_field and dss_clk_source_name have enum members which
specify the register field and the clock source respectively. These members are
not used to choose the correct result in the corresponding feature functions.
Remove these members and change the features array declaration to incorporate
these enums.
The structure dss_clk_source_name without the enum member is just a pointer to
an string. Remove the structure and use a character pointer directly.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Something seems to be wrong with OMAP4 & VENC, and register access fails
in omap_venchw_probe().
This patch skips venc driver registration on OMAP4, thus circumventing
the problem for now.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This patch splits the pll configs up on pll versions. This allows
easy adding of other known good pll values. Additionally it made it
possible to remove invalid configurations resulting in better
behaviour for such cases. The resulting clocks are no longer stored
resulting in some computing overhead on each mode change.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The clocks can be easily recalculated by the timing and refresh value.
This brings us one step closer to removing VIAs modetable and use
generic ones and being easier extensible.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Before this patch only clocks that perfectly match were used and if
none existed this was not handled properly. This patch changes this
to always use the closest clock supported. This should behave like
before for clocks that have a perfect match but be much saner for
clocks which are slightly off.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch removes the direct lookup table for resolution+refresh and
pixclock by calculating this information from the mode table. Removes a
lot of dupllication and error potential by just doing a little more
calculations on each mode change.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
On OMAP3, the pixel clock for the LCD manager was derived through DISPC_FCLK as:
Lcd Pixel clock = DISPC_FCLK / lcd / pcd
Where lcd and pcd are divisors in the DISPC_DIVISOR register.
On OMAP4, the pixel clocks for LCD1 and LCD2 managers are derived from 2 new
clocks named LCD1_CLK and LCD2_CLK. The pixel clocks are calculated as:
Lcd_o Pixel clock = LCDo_CLK / lcdo /pcdo, o = 1, 2
Where lcdo and pcdo registers are divisors in DISPC_DIVISORo registers.
LCD1_CLK and LCD2_CLK can have DSS_FCLK, and the M4 divider clocks of DSI1 PLL
and DSI2 PLL as clock sources respectively. Introduce functions to select and
get the clock source for these new clocks. Modify DISPC functions get the
correct lck and pck rates based on the clock source of these clocks. Since
OMAP2/3 don't have these clocks, force OMAP2/3 to always have the LCD_CLK source
as DSS_CLK_SRC_FCK by introducing a dss feature.
Introduce clock source names for OMAP4 and some register field changes in
DSS_CTRL on OMAP4.
Currently, LCD2_CLK can only have DSS_FCLK as its clock source as DSI2 PLL
functionality hasn't been introduced yet. BUG for now if DSI2 PLL is selected as
clock.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Clean up some of the DSS functions which select/get clock sources, use switch
to select the clock source members since more clock sources will be introduced
later on.
Remove the use of macro CONFIG_OMAP2_DSS_DSI in dispc_fclk_rate, use a dummy
inline for function for dsi_get_pll_hsdiv_dispc_rate() instead for code clarity.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This patch adds support for the Gumstix Palo35 expansion board
which utilizes the 320 x 240 pixel LG.Philips LB035Q02 LCD Panel
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Fix handling of error in omap_dispc_register_isr() in case there are no
free isr slots available.
Reported-by: Ben Tucker <btucker@mpcdata.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Using dss_features to select independent core clock divider and setting
it. Added the register used, to DISPC context save and restore group
-----------------------------------------------------------------------
In OMAP4, the minimum DISPC_CORE_CLK required can be expressed as:
DISPC_CORE_CLK >= max(PCLK1*HSCALE1, PCLK2*HSCALE2, ...)
Where PCLKi is the pixel clock generated by MANAGERi and HSCALEi is the
maximum horizontal downscaling done through MANAGERi
Based on the usecase, core clk can be increased or decreased at runtime
to save power. Such mechanism are not yet implemented. Hence, we set the
core clock divisor to 1, to support maximum range of resolutions
------------------------------------------------------------------------
Signed-off-by: Raghuveer Murthy <raghuveer.murthy@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The OMAP4 DISPC_DIVISOR1 is backward compatible to OMAP3xxx DISPC_DIVISOR.
However DISPC_DIVISOR is also provided in OMAP4, to control DISPC_CORE_CLK
independent of Primary and Secondary display clocks.
Renamed DISPC_DIVISOR(ch) to DISPC_DIVISORo(ch), to facilitate introduction
of DISPC_DIVISOR register, which is specific for OMAP4. OMAP4 has 3 registers
DISPC_DIVISOR, DISPC_DIVISOR1 and DISPC_DIVISOR2.
Also updated, all the usages of DISPC_DIVISOR(ch) to DISPC_DIVISORo(ch).
Use DISPC_DIVISORo(ch) when DISPC_DIVISOR1 or DISPC_DIVISOR2 has to be
configured
OMAP4 TRM uses DISPC_DIVISORo generically to refer to DISPC_DIVISOR1 and
DISPC_DIVISOR2
Signed-off-by: Raghuveer Murthy <raghuveer.murthy@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In OMAP3xxx DISPC_DIVISOR register has a logical clock divisor (lcd_div)
field. The lcd_div is common, for deciding the DISPC core functional clock
frequency, and the final pixel clock frequency for LCD display.
In OMAP4, there are 2 LCD channels, hence two divisor registers, DISPC_DIVISOR1
and DISPC_DIVISOR2. Also, there is a third register DISPC_DIVISOR.
The DISPC_DIVISOR in OMAP4 is used to configure lcd_div exclusively for core
functional clock configuration. For pixel clock configuration of primary and
secondary LCDs, lcd_div of DISPC_DIVISOR1 and DISPC_DIVISOR2 are used
respectively
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Raghuveer Murthy <raghuveer.murthy@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
On omap4 the registers may not be accessible right after enabling the
clocks. At some point this will be handled by pm_runtime, but, for the
time begin, adding a small delay after clk_enable() should make things
work.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When using OMAP2_DSS_USE_DSI_PLL, which selects DSI PLL as source clock
for DISPC, the DSI needs the vdds_dsi regulator. Latest regulator
changes broke this, causing the the code to not acquire the regulator
when using OMAP2_DSS_USE_DSI_PLL.
This patch acquires the vdds_dsi regulator in dsi_pll_init(), fixing the
issue. This is is just a quick hack to get the OMAP2_DSS_USE_DSI_PLL
option working. There shouldn't be any other downside in this solution
than some extra lines of code.
OMAP2_DSS_USE_DSI_PLL is itself a big hack, and should be removed, and
the feature itself should be implemented in a more sane way. However,
the solution is not trivial, and people are using DSI PLL to get more
exact pixel clocks, so this hack is an acceptable temporary solution for
the time being.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Taal driver used to take a hard coded Macro for Virtual Channel and the VC_ID.
The Taal panel driver now requests for a Virtual channel through the
omap_dsi_request_vc() call in taal_probe().
The channel number returned by the request_vc() call is used for sending command
and data to the Panel. The DSI driver automatically configures the Virtual
Channel's source to either Video Port or L4 Slave port based on what the panel
driver is using it for.
The driver uses omap_dsi_release_vc() to free the VC specified by the panel.
taal_remove() or when a request_vc() call fails.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Introduce functions which request and release VC's. This will be used in panel
drivers in their probes.
omap_dsi_request_vc() takes in the pointer to the omap_dss_device, the VC_ID
parameter which goes into the header of the DSI packets, and returns a Virtual
channel number (or virtual channel register set) which it can use.
omap_dsi_set_vc_id() takes the omap_dss_device pointer, the Virtual Channel
number and the VC_ID that needs to be set for the specifed Virtual Channel.
omap_dsi_release_vc() takes the omap_dss_device pointer and the Virtual Channel
number that needs to be made free.
Initialisation of VC parameters is done in dsi_init().
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
cpu_is_omapxxx() was used previously to select the supported interfaces.
Now that the interfaces are platform devices, we no longer need to do
the check when registering the driver. Thus we can just remove the
checks.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DPI and SDI are different from the other interfaces as they are not
hwmods and there is not platform driver for them. They could be said to
be a part of DSS or DISPC modules, although it's not a clear definition.
This patch moves DPI and SDI initialization into DSS platform driver,
making the code more consistent: omap_dss_probe() only initializes
platform drivers now.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
FB_OMAP_BOOTLOADER_INIT does not work, and it was only partially
implemented for SDI.
This patch removes support for FB_OMAP_BOOTLOADER_INIT to clean up the
code and to remove any assumptions that FB_OMAP_BOOTLOADER_INIT would
work.
Proper implementation is much more complex, requiring early boot time
register and clock handling to keep the DSS running.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DSI PLL output clock names have been made more generic. The clock name
describes what the source of the clock and what clock is used for. Some of
DSI PLL parameters like dividers and DSI PLL source have also been made more
generic.
dsi1_pll_fclk and dsi2_pll_fclk have been changed as dsi_pll_hsdiv_dispc_clk
and dsi_pll_hsdiv_dsi_clk respectively. Also, the hsdividers are now named
regm_dispc and regm_dsi instead of regm3 and regm4.
Functions and macros named on the basis of these clock names have also been
made generic.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Clock source names vary across OMAP2/3 and OMAP4, the clock source enum
names have been made generic in the driver, but for purposes of debugging
and dumping clock sources, it is better to preserve the actual TRM name of
the clock.
Introduce a dss feature function 'dss_feat_get_clk_source_name()' which
returns a string with the TRM clock name for the current OMAP in use. The OMAP
specific name is printed along the generic name within brackets.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The enum members of 'dss_clk_source' have clock source names specific to
OMAP2/3. Change the names to more generic terms such that they now describe
where the clocks come from and what they are used for.
Also, change the enum member names to have "DSS_CLK_SRC" instead of "DSS_SRC"
for more clarity.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The maximum supported frequency for DSS has increased from 173 to 186 Mhz on
OMAP4.
Introduce a dss feature function to get the max_fck to replace DISPC_MAX_FCK
macro.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add dss_features and register fields to incorporate changes in DISPC pipelines
between OMAP3 and OMAP4.
Register fields added: FEAT_REG_HORIZONTALACCU, FEAT_REG_VERTICALACCU
DSS Features added: FEAT_LINEBUFFERSPLIT, FEAT_ROWREPEATENABLE, FEAT_RESIZECONF
_dispc_set_scaling() and _dispc_set_rotation_attrs() have been cleaned up.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
There is a linker error from lcd_2430sdp.c if CONFIG_TWL4030_CORE is not
set. This can be triggered on OMAP2 builds when OMAP3 or OMAP4 are not set.
drivers/built-in.o: In function `sdp2430_panel_disable':
drivers/video/omap/lcd_2430sdp.c:123: undefined reference to `twl_i2c_write_u8'
drivers/video/omap/lcd_2430sdp.c:124: undefined reference to `twl_i2c_write_u8'
drivers/built-in.o: In function `sdp2430_panel_enable':
drivers/video/omap/lcd_2430sdp.c:110: undefined reference to `twl_i2c_write_u8'
drivers/video/omap/lcd_2430sdp.c:112: undefined reference to `twl_i2c_write_u8'
Fix this by selecting the TWL4030_CORE for MACH_OMAP_2430SDP when building
with CONFIG_FB_OMAP as there is no own Kconfig entry for lcd_2430 and it is
compiled always when both MACH_OMAP_2430SDP and FB_OMAP are set.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
hwmod databases provide information about which optional clocks are available
for a given platform. This is available via a function pointer opt_clock_enable
in pdata.
Use this information during get/enable/disable/put of clocks.
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dsi_reset_tx_fifo() was not used. Furthermore, OMAP errata states that
TX FIFO flush is not functional, so the function wouldn't even have
worked.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
CONFIG_FB_OMAP_LCD_VGA option is present in drivers/video/omap
There is no explaination about what this flag does.
Lets add information about it.
FB_OMAP_LCD_VGA flag sets resolution of display to VGA (640 X 480).
The default resolution of 3430 LDP is 320 X 240.
Signed-off-by: Mayuresh Janorkar <mayur@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Only OMAP 3430 hardware has SDI support. The availability of SDI HW can
be found out by checking if the LCD channel supports SDI displays.
This patch checks for SDI HW support before accessing SDI registers,
which fixes a crash on OMAP4 when SDI SW support is compiled in.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
OMAP 3630 does not support SDI. Split omap3_dss_supported_displays into
3430 and 3630 entries, and remove the SDI from 3630 entry.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Support for the display interface was checked in a separate switch-case.
There's no reason for that, and this patch handles the fail code path in
the same switch-case where the display initialization is done.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Currently, the core DSS platform device requests for an irq line for OMAP2 and
OMAP3. Make DISPC and DSI platform devices request for a shared IRQ line.
On OMAP3, the logical OR of DSI and DISPC interrupt lines goes to the MPU. There
is a register DSS_IRQSTATUS which tells if the interrupt came from DISPC or DSI.
On OMAP2, there is no DSI, only DISPC interrupts goto the MPU. There is no
DSS_IRQSTATUS register.
Hence, it makes more sense to have separate irq handlers corresponding to the
DSS sub modules instead of having a common handler.
Since on OMAP3 the logical OR of the lines goes to MPU, the irq line is shared
among the IRQ handlers.
The hwmod irq info has been removed for DSS to DISPC and DSI for OMAP2 and OMAP3
hwmod databases. The Probes of DISPC and DSI now request for irq handlers.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When omapfb.mode is passed through bootargs, when omapfb is setting mode,
it would check if timings passed are fine for panel attached to it.
It makes use of check_timing API provided by the panel.
In current code if check_timing API is not available for attached panel,
OMAPFB would return -EINVAL and BPP sent via bootargs will not have any effect.
In case of panels like TAAL panel, omapfb or any other driver should not be allowed to
change the timings. So bpps sent via bootargs will not have an effect.
In such case we can check only the x_res and y_res with the panels resolution
and if they match go ahead and set the bpps.
The bpp value sent via bootarg would have an effect.
Signed-off-by: Mayuresh Janorkar <mayur@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DSS submodules DPI/SDI/DSI/VENC require a regulator to function.
However, if the board doesn't use, say, SDI, the board shouldn't need to
configure vdds_sdi regulator required by the SDI module.
Currently the regulators are acquired when the DSS driver is loaded.
This means that if the kernel is configured with SDI, vdds_sdi regulator
is needed for all boards.
This patch changes the DSS driver to acquire the regulators only when a
display of particular type is initialized. For example, vdds_sdi is
acquired when sdi_init_display() is called.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
MODULE_PARM_DESC() takes the name of the actual module parameter, not the
name of the variable, as input. Fix the module parameter description for
def_disp.
Signed-off-by: Jani Nikula <jani@nikula.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The dss struct in dss.c has omap2/3 specific clock names. Making them generic,
to increase readability and extendability.
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
enum dss_clock structure is replaced with generic names that
could be used across OMAP2420, 2430, 3xxx, 44xx platforms.
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tomi Valkeinen