Make banner const while we're at it
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Simon Horman <horms@verge.net.au>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When unbinding a serial driver that's being used as a serial console,
the kernel may crash with a NULL pointer dereference in a uart_*() function
called from uart_close () (e.g. uart_flush_buffer() or
uart_chars_in_buffer()).
To fix this, let uart_close() check for port->count == 0. If this is the
case, bail out early. Else tty_port_close_start() will make the port
counts inconsistent, printing out warnings like
tty_port_close_start: tty->count = 1 port count = 0.
and
tty_port_close_start: count = -1
and once uport == NULL, it will also crash.
Also fix the related crash in pr_debug() by checking for a non-NULL uport
first.
Detailed description:
On driver unbind, uart_remove_one_port() is called. Basically it;
- marks the port dead,
- calls tty_vhangup(),
- sets state->uart_port = NULL.
What will happen depends on whether the port is just in use by e.g. getty,
or was also opened as a console.
A. If the tty was not opened as a console:
- tty_vhangup() will (in __tty_hangup()):
- mark all file descriptors for this tty hung up by pointing them to
hung_up_tty_fops,
- call uart_hangup(), which sets port->count to 0.
- A subsequent uart_open() (this may be through /dev/ttyS*, or through
/dev/console if this is a serial console) will fail with -ENXIO as the
port was marked dead,
- uart_close() after the failed uart_open() will return early, as
tty_hung_up_p() (called from tty_port_close_start()) will notice it was
hung up.
B. If the tty was also opened as a console:
- tty_vhangup() will (in __tty_hangup()):
- mark non-console file descriptors for this tty hung up by pointing
them to hung_up_tty_fops,
- NOT call uart_hangup(), but instead call uart_close() for every
non-console file descriptor, so port->count will still have a
non-zero value afterwards.
- A subsequent uart_open() will fail with -ENXIO as the port was
marked dead,
- uart_close() after the failed uart_open() starts to misbehave:
- tty_hung_up_p() will not notice it was hung up,
- As port->count is non-zero, tty_port_close_start() will decrease
port->count, making the tty and port counts inconsistent. Later,
warnings like these will be printed:
tty_port_close_start: tty->count = 1 port count = 0.
and
tty_port_close_start: count = -1
- If all of this happens after state->uart_port was set to zero, a
NULL pointer dereference will happen.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds cond_sched() calls during wait loop to perform
other tasks.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While reviewing an i2c driver for efm32 that needs a similar property
Wolfram Sang pointed out that "location" is a too generic name for something
that is efm32 specific. So add an appropriate namespace and fall back to the
generic name in case of failure.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cris allmodconfig:
drivers/tty/serial/max310x.c: In function 'max310x_ioctl':
drivers/tty/serial/max310x.c:885:3: error: implicit declaration of function 'copy_from_user' [-Werror=implicit-function-declaration]
drivers/tty/serial/max310x.c:916:3: error: implicit declaration of function 'copy_to_user' [-Werror=implicit-function-declaration]
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hdlcdev_ioctl() code fails to initialize the two padding bytes of
struct sync_serial_settings after the ->loopback member. Add an explicit
memset(0) before filling the structure to avoid the info leak.
Signed-off-by: Salva Peiró <speiro@ai2.upv.es>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In -RT the spin_lock_irqsave() does not spin but sleep if the lock is
taken. Before that, local_irq_save() is invoked which disables
interrupts even on -RT. Therefore local_irq_save() + spin_lock() does not
work.
In the ->sysrq and oops_in_progress case it is save to trylock the lock
i.e. this is what we do now anyway except for ->sysrq where we assume
that the lock is already taken.
The spin_lock_irqsave() grabs the lock and disables the interrupts on
vanilla (the same behavior) and on -RT it won't disable interrupts.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[bigeasy: add a patch description]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Support the following additional baud rates with 0% error:
500000, 1500000, 2500000, 3500000
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJS3IyXAAoJEHm+PkMAQRiGplAH/ilCikBrCHyZ2938NHNLm+j1
yhfYnEJHLNg7T69KEj3p0cNagO3v9RPWM6UYFBQ6uFIYNN1MBKO7U+mCZuMWzeO8
+tGMV3mn5wx+oYn1RnWCCweQx5AESEl6rYn8udPDKh7LfW5fCLV60jguUjVSQ9IQ
cvtKlWknbiHyM7t1GoYgzN7jlPrRQvcNQZ+Aogzz7uSnJAgwINglBAHS7WP2tiEM
HAU2FoE4b3MbfGaid1vypaYQPBbFebx7Bw2WxAuZhkBbRiUBKlgF0/SYhOTvH38a
Sjpj1EHKfjcuCBt9tht6KP6H56R25vNloGR2+FB+fuQBdujd/SPa9xDflEMcdG4=
=iXnG
-----END PGP SIGNATURE-----
Merge tag 'v3.13' into for-3.15
Linux 3.13
Conflicts:
include/net/xfrm.h
Simple merge where v3.13 removed 'extern' from definitions and the audit
tree did s/u32/unsigned int/ to the same definitions.
If cpufreq_register_notifier() fails, we have to remove the port added by
sci_probe_single(), which is not done by sci_cleanup_single().
Else the serial port stays active from the point of view of the serial
subsystem, and it may crash when userspace getty is started, or when the
loadable driver module is unloaded.
This was introduced by commit 6dae14216c
("serial: sh-sci: Fix probe error paths").
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the serial port being removed is used as a console, it must also be
unregistered from the console subsystem using unregister_console().
uart_ops.release_port() will release resources (e.g. iounmap() the serial
port registers), causing a crash on subsequent kernel output if the console
is still registered.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 95e629b761 removed the use of board
specific hooks in serial_at91.h, so now, the open/close hook are just
dead code.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'active' sysfs attribute should refer to the currently active tty
devices the console is running on, not the currently active console. The
console structure doesn't refer to any device in sysfs, only the tty the
console is running on has. So we need to print out the tty names in
'active', not the console names.
There is one special-case, which is tty0. If the console is directed to
it, we want 'tty0' to show up in the file, so user-space knows that the
messages get forwarded to the active VT. The ->device() callback would
resolve tty0, though. Hence, treat it special and don't call into the VT
layer to resolve it (plymouth is known to depend on it).
Cc: Lennart Poettering <lennart@poettering.net>
Cc: Kay Sievers <kay@vrfy.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Werner Fink <werner@suse.de>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use devm_ioremap_resource() in order to make the code simpler and
it gives proper codes on errors.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The user-settable knob, low_latency, has been the source of
several BUG reports which stem from flush_to_ldisc() running
in interrupt context. Since 3.12, which added several sleeping
locks (termios_rwsem and buf->lock) to the input processing path,
the frequency of these BUG reports has increased.
Note that changes in 3.12 did not introduce this regression;
sleeping locks were first added to the input processing path
with the removal of the BKL from N_TTY in commit
a88a69c912,
'n_tty: Fix loss of echoed characters and remove bkl from n_tty'
and later in commit 38db89799b,
'tty: throttling race fix'. Since those changes, executing
flush_to_ldisc() in interrupt_context (ie, low_latency set), is unsafe.
However, since most devices do not validate if the low_latency
setting is appropriate for the context (process or interrupt) in
which they receive data, some reports are due to misconfiguration.
Further, serial dma devices for which dma fails, resort to
interrupt receiving as a backup without resetting low_latency.
Historically, low_latency was used to force wake-up the reading
process rather than wait for the next scheduler tick. The
effect was to trim multiple milliseconds of latency from
when the process would receive new data.
Recent tests [1] have shown that the reading process now receives
data with only 10's of microseconds latency without low_latency set.
Remove the low_latency rx steering from tty_flip_buffer_push();
however, leave the knob as an optional hint to drivers that can
tune their rx fifos and such like. Cleanup stale code comments
regarding low_latency.
[1] https://lkml.org/lkml/2014/2/20/434
"Yay.. thats an annoying historical pain in the butt gone."
-- Alan Cox
Reported-by: Beat Bolli <bbolli@ewanet.ch>
Reported-by: Pavel Roskin <proski@gnu.org>
Acked-by: David Sterba <dsterba@suse.cz>
Cc: Grant Edwards <grant.b.edwards@gmail.com>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Hal Murray <murray+fedora@ip-64-139-1-69.sjc.megapath.net>
Cc: <stable@vger.kernel.org> # 3.12.x+
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a matching table for the the bcm63xx_uart driver on the compatible
string "brcm,bcm6345-uart" which covers all BCM63xx implementations and
reflects the fact that this block was first introduced with the BCM6345
SoC. Also make sure that we convert the id based on the uart aliases
provided by the relevant Device Tree.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bcm63xx_uart driver uses RSET_UART_SIZE which is a constant defined
for MIPS-based BCM63xx platforms, pull this constant value from the
MIPS-specific header and put it in include/linux/serial_bcm63xx.h to
make the driver platform agnostic.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Include linux/io.h which provides the definition for
__raw_{readl,writel}, this is not necessary on MIPS since there is an
implicit inclusion, but it is on ARM for instance.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These can be used to send commands consisting of an arbitrary string to the
terminal, most often used to set a terminal's window title or to redefine
the colour palette. Our console doesn't use OSC, unlike everything else,
which can lead to junk being displayed if a process sends such a code
unconditionally.
The rules for termination follow established practice rather than Ecma-48.
Ecma-48 requires the string to use only byte values 0x08..0x0D and
0x20..0x7E, terminated with either ESC \ or 0x9C. This would disallow using
8-bit characters, which are reasonable for example in window titles.
A widespread idiom is to terminate with 0x07. The behaviour for other
control characters differs between terminal emulators, I followed libvte and
xterm:
* 0x07 and ESC anything terminate
* nothing else terminates, all 8-bit values including 0x9C are considered a
part of the string
Signed-off-by: Adam Borowski <kilobyte@angband.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Every couple of months, someone sends a patch to fix:
drivers/tty/serial/8250/8250_core.c: In function 'serial_unlink_irq_chain':
drivers/tty/serial/8250/8250_core.c:1712:2: warning: 'i' may be used uninitialized in this function [-Wuninitialized]
and they in turn get a NACK for their efforts, and are told that
their compiler is broken. This has been going on since at least
the year 2008: https://lkml.org/lkml/2008/11/24/433
Lets add a comment, so that subsequent patches don't get as far as
the maintainers or the mailing lists.
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Merge "qcom driver changes for v3.15" from Kumar Gala:
We've split Qualcomm MSM support into legacy and multiplatform. These
drivers are only relevant on the multiplatform supported SoCs so switch the
Kconfig depends to ARCH_QCOM.
* tag 'qcom-drivers-for-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom:
gpio: msm: switch Kconfig to ARCH_QCOM depends
hwrng: msm: switch Kconfig to ARCH_QCOM depends
power: reset: msm - switch Kconfig to ARCH_QCOM depends
drm/msm: drop ARCH_MSM Kconfig depend
tty: serial: msm: Enable building msm_serial for ARCH_QCOM
This reverts commit d8a5dc3033.
This breaks plymouth installs, either because plymouth is using the file
"incorrectly" or because the patch is incorrect. Either way, this needs
to be reverted until it is all figured out.
Reported-by: Josh Boyer <jwboyer@fedoraproject.org>
Reported-by: Ray Strode <halfline@gmail.com>
Cc: Lennart Poettering <lennart@poettering.net>
Cc: Kay Sievers <kay@vrfy.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: David Herrmann <dh.herrmann@gmail.com>
Cc: Werner Fink <werner@suse.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ARCH_MULTIPLATFORM. (For multi-platform code it's already unused since
387798b (ARM: initial multiplatform support).)
To make this work some code out of arch/arm needed to be adapted. The
respective changes got acks by their maintainers to be taken via armsoc
(with Andrew Morton substituting for Alessandro Zummo as rtc maintainer).
Compared to the previous pull request there was another patch added that
fixes a (non-critical) regression on ixp4xx. Olof Johansson asked to not
squash this fix into the original commit to save him from the need to
reverify the series.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=g6PN
-----END PGP SIGNATURE-----
Merge tag 'dropmachtimexh-v2' of git://git.pengutronix.de/git/ukl/linux into next/cleanup
This cleanup series gets rid of <mach/timex.h> for platforms not using
ARCH_MULTIPLATFORM. (For multi-platform code it's already unused since
387798b (ARM: initial multiplatform support).)
To make this work some code out of arch/arm needed to be adapted. The
respective changes got acks by their maintainers to be taken via armsoc
(with Andrew Morton substituting for Alessandro Zummo as rtc maintainer).
Compared to the previous pull request there was another patch added that
fixes a (non-critical) regression on ixp4xx. Olof Johansson asked to not
squash this fix into the original commit to save him from the need to
reverify the series.
* tag 'dropmachtimexh-v2' of git://git.pengutronix.de/git/ukl/linux:
ARM: ixp4xx: fix timer latch calculation
ARM: drop <mach/timex.h> for !ARCH_MULTIPLATFORM, too
ARM: rpc: stop using <mach/timex.h>
ARM: ixp4xx: stop using <mach/timex.h>
input: ixp4xx-beeper: don't use symbols from <mach/timex.h>
ARM: at91: don't use <mach/timex.h>
ARM: ep93xx: stop using mach/timex.h
ARM: mmp: stop using mach/timex.h
ARM: netx: stop using mach/timex.h
ARM: sa1100: stop using mach/timex.h
clocksource: sirf/marco+prima2: drop usage of CLOCK_TICK_RATE
rtc: pxa: drop unused #define TIMER_FREQ
rtc: at91sam9: include <mach/hardware.h> explicitly
ARM/serial: at91: switch atmel serial to use gpiolib
Signed-off-by: Olof Johansson <olof@lixom.net>
Add dma support for lpuart. This function depend on DMA driver.
You can turn on it by write both the dmas and dma-name properties in dts node.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kconfig symbol SVINTO_SIM got dropped in commit e269a86941 ("Drop
code for CRISv10 CPU simulator"). Now drop the remaining code for that
simulator.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a temporary solution to fix following issue:
config: make ARCH=alpha allyesconfig
All error/warnings:
drivers/tty/serial/max310x.c: In function 'max310x_ioctl':
>> drivers/tty/serial/max310x.c:905:7: error: 'TIOCSRS485' undeclared (first use in this function)
drivers/tty/serial/max310x.c:905:7: note: each undeclared identifier is reported only once for each function it appears in
>> drivers/tty/serial/max310x.c:906:3: error: implicit declaration of function 'copy_from_user' [-Werror=implicit-function-declaration]
>> drivers/tty/serial/max310x.c:929:7: error: 'TIOCGRS485' undeclared (first use in this function)
>> drivers/tty/serial/max310x.c:938:3: error: implicit declaration of function 'copy_to_user' [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit e3c6ea9b1b as it
didn't help anything, and caused more problems than expected.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
\E[3J console code (secure clear screen) needs to update_screen(vc)
in order to write-through blanks into off-screen video memory.
This has been removed accidentally in 3.6 by:
commit 81732c3b2f
Author: Jean-François Moine <moinejf@free.fr>
Date: Thu Sep 6 19:24:13 2012 +0200
tty vt: Fix line garbage in virtual console on command line edition
Signed-off-by: Petr Písař <petr.pisar@atlas.cz>
Cc: stable <stable@vger.kernel.org> # 3.6
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 3e6c6f630a ("Delay creation of
khcvd thread") moved the call of hvc_init from being a device_initcall
into hvc_alloc, and used a non-null hvc_driver as indication of whether
hvc_init had already been called.
The problem with this is that hvc_driver is only assigned a value
at the bottom of hvc_init, and so there is a window where multiple
hvc_alloc calls can be in progress at the same time and hence try
and call hvc_init multiple times. Previously the use of device_init
guaranteed that hvc_init was only called once.
This manifests itself as sporadic instances of two hvc_init calls
racing each other, and with the loser of the race getting -EBUSY
from tty_register_driver() and hence that virtual console fails:
Couldn't register hvc console driver
virtio-ports vport0p1: error -16 allocating hvc for port
Here we add an atomic_t to guarantee we'll never run hvc_init twice.
Cc: stable@vger.kernel.org # v2.6.24+
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: 3e6c6f630a ("Delay creation of khcvd thread")
Reported-by: Jim Somerville <Jim.Somerville@windriver.com>
Tested-by: Jim Somerville <Jim.Somerville@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
instead of using sirf specific dma channel property like "sirf,uart-dma-rx-channel"
and "sirf,uart-dma-tx-channel", here we move to use generic dma dt-binding to get
the channel like:
- sirf,uart-dma-rx-channel = <21>;
- sirf,uart-dma-tx-channel = <2>;
+ dmas = <&dmac1 5>, <&dmac0 2>;
+ dma-names = "rx", "tx";
and we move dma_request_channel() to dma_request_slave_channel(), we don't need to
call sirfsoc dma filter function sirfsoc_dma_filter_id() again.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_register_driver call binds the driver to a specific device
node through tty_register_driver call. This should typically happen
during device probe call.
In a multiplatform scenario, it is possible that multiple serial
drivers are part of the kernel. Currently the driver registration fails
if multiple serial drivers with same default major/minor numbers are
included in the kernel.
A typical case is observed with amba-pl011 and samsung-uart drivers.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_register_driver call binds the driver to a specific device
node through tty_register_driver call. This should typically happen
during device probe call.
In a multiplatform scenario, it is possible that multiple serial
drivers are part of the kernel. Currently the driver registration fails
if multiple serial drivers with same default major/minor numbers are
included in the kernel.
A typical case is observed with amba-pl011 and samsung-uart drivers.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
config: x86_64-randconfig-x006 (attached as .config)
All warnings:
drivers/tty/serial/max310x.c: In function 'max310x_probe':
>> drivers/tty/serial/max310x.c:1240:1: warning: label 'out_uart' defined but not used [-Wunused-label]
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
config: make ARCH=alpha allyesconfig
All error/warnings:
drivers/tty/serial/max310x.c: In function 'max310x_ioctl':
>> drivers/tty/serial/max310x.c:905:7: error: 'TIOCSRS485' undeclared (first use in this function)
drivers/tty/serial/max310x.c:905:7: note: each undeclared identifier is reported only once for each function it appears in
>> drivers/tty/serial/max310x.c:906:3: error: implicit declaration of function 'copy_from_user' [-Werror=implicit-function-declaration]
>> drivers/tty/serial/max310x.c:929:7: error: 'TIOCGRS485' undeclared (first use in this function)
>> drivers/tty/serial/max310x.c:938:3: error: implicit declaration of function 'copy_to_user' [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current code only wakes up the processes when the circle
buffer has less data then the WAKEUP_CHARS.
But sometimes, the circle buffer may has data more then the WAKEUP_CHARS,
in such case, the processes will hang.
This patch makes it always wakes up the processes in the TX callback.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes a driver bug which stopped the whole system (in case
of serial console).
This log message is not useful anyway as this information is
printed elsewhere.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Exar XR17V35x family of UARTs have an additional fractional divisor
register (DLD) which was not being used. Calculate and set this
register for these devices to reduce their baud rate error.
Signed-off-by: Joe Schultz <jschultz@xes-inc.com>
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When echoes cannot be flushed to output (usually because the tty
has no more write room) and L_ECHO is subsequently turned off, then
when L_ECHO is turned back on, stale echoes are output.
Output completed echoes regardless of the L_ECHO setting:
1. before normal writes to that tty
2. if the tty was stopped by soft flow control and is being
restarted
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: <stable@vger.kernel.org> # 3.13.x
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8b9ade9f74 coming from Viresh Kumar "tty: serial: sirfsoc: drop
uart_port->lock before calling tty_flip_buffer_push()" broke sirfsoc uart
driver by knic:
[ 5.129122] BUG: spinlock already unlocked on CPU#0, ip6tables/1331
[ 5.132554] lock: sirfsoc_uart_ports+0x4/0x8a0, .magic: dead4ead,
.owner: <none>/-1, .owner_cpu: -1
[ 5.141651] CPU: 0 PID: 1331 Comm: ip6tables Tainted: G
W O 3.10.16 #3
[ 5.148866] [<c0013528>] (unwind_backtrace+0x0/0xe0) from
[<c0010e70>] (show_stack+0x10/0x14)
[ 5.157362] [<c0010e70>] (show_stack+0x10/0x14) from
[<c01a5e68>] (do_raw_spin_unlock+0x40/0xc8)
[ 5.166125] [<c01a5e68>] (do_raw_spin_unlock+0x40/0xc8) from
[<c03ff8b4>] (_raw_spin_unlock+0x8/0x40)
[ 5.175322] [<c03ff8b4>] (_raw_spin_unlock+0x8/0x40) from
[<c0203fcc>] (sirfsoc_uart_pio_rx_chars+0xa4/0xc0)
[ 5.185120] [<c0203fcc>]
(sirfsoc_uart_pio_rx_chars+0xa4/0xc0) from [<c0204fb8>]
(sirfsoc_rx_tmo_process_tl+0xdc/0x1e0)
[ 5.195875] [<c0204fb8>]
(sirfsoc_rx_tmo_process_tl+0xdc/0x1e0) from [<c0024b50>]
(tasklet_action+0x8c/0xec)
[ 5.205673] [<c0024b50>] (tasklet_action+0x8c/0xec) from
[<c00242a8>] (__do_softirq+0xec/0x1d4)
[ 5.214347] [<c00242a8>] (__do_softirq+0xec/0x1d4) from
[<c0024428>] (do_softirq+0x48/0x54)
[ 5.222674] [<c0024428>] (do_softirq+0x48/0x54) from
[<c0024690>] (irq_exit+0x74/0xc0)
[ 5.230573] [<c0024690>] (irq_exit+0x74/0xc0) from
[<c000e1e8>] (handle_IRQ+0x6c/0x90)
[ 5.238465] [<c000e1e8>] (handle_IRQ+0x6c/0x90) from
[<c000d500>] (__irq_svc+0x40/0x70)
[ 5.246446] [<c000d500>] (__irq_svc+0x40/0x70) from
[<c0092e7c>] (mark_page_accessed+0xc/0x68)
[ 5.255034] [<c0092e7c>] (mark_page_accessed+0xc/0x68) from
[<c00a2a4c>] (unmap_single_vma+0x3bc/0x550)
[ 5.264402] [<c00a2a4c>] (unmap_single_vma+0x3bc/0x550) from
[<c00a3b4c>] (unmap_vmas+0x44/0x54)
[ 5.273164] [<c00a3b4c>] (unmap_vmas+0x44/0x54) from
[<c00a81a8>] (exit_mmap+0xc4/0x1e0)
[ 5.281233] [<c00a81a8>] (exit_mmap+0xc4/0x1e0) from
[<c001bb78>] (mmput+0x3c/0xdc)
[ 5.288868] [<c001bb78>] (mmput+0x3c/0xdc) from [<c0021b0c>]
(do_exit+0x30c/0x828)
[ 5.296413] [<c0021b0c>] (do_exit+0x30c/0x828) from
[<c0022dac>] (do_group_exit+0x4c/0xb0)
[ 5.304653] [<c0022dac>] (do_group_exit+0x4c/0xb0) from
[<c0022e20>] (__wake_up_parent+0x0/0x18)
Root cause:
the commit dropped uart_port->lock before calling tty_flip_buffer_push(), but in sirfsoc-uart,
sirfsoc_uart_pio_rx_chars() can be called by sirfsoc_rx_tmo_process_tl(). here uart_port->lock
has not been taken yet. so that caused unpaired lock/unlock.
Solution:
This patch is doing a quick fix for that, it adds spin_lock/unlock(&port->lock) protect to
sirfsoc_uart_pio_rx_chars() in sirfsoc_rx_tmo_process_tl() to keep spin_lock/unlock in pair.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Cc: stable <stable@vger.kernel.org> # 3.12
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Aparently 9865 uses standard BAR encoding scheme (unlike 99xx cards).
Current pci_netmos_9900_setup() uses wrong BAR indices for the 9865 PCI
device, function 2. Using standard BAR indices makes all 6 ports work
for me. Thus disable the NetMos 9900 quirk for NetMos 9865 pci device.
For the reference, here is the relevant part of lspci for my device:
02:07.0 Serial controller: MosChip Semiconductor Technology Ltd. PCI
9865 Multi-I/O Controller (prog-if 02 [16550])
Subsystem: Device a000:1000
Flags: bus master, medium devsel, latency 32, IRQ 17
I/O ports at ac00 [size=8]
Memory at fcfff000 (32-bit, non-prefetchable) [size=4K]
Memory at fcffe000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [48] Power Management version 2
Kernel driver in use: serial
02:07.1 Serial controller: MosChip Semiconductor Technology Ltd. PCI
9865 Multi-I/O Controller (prog-if 02 [16550])
Subsystem: Device a000:1000
Flags: bus master, medium devsel, latency 32, IRQ 18
I/O ports at a800 [size=8]
Memory at fcffd000 (32-bit, non-prefetchable) [size=4K]
Memory at fcffc000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [48] Power Management version 2
Kernel driver in use: serial
02:07.2 Communication controller: MosChip Semiconductor Technology Ltd.
PCI 9865 Multi-I/O Controller
Subsystem: Device a000:3004
Flags: bus master, medium devsel, latency 32, IRQ 19
I/O ports at a400 [size=8]
I/O ports at a000 [size=8]
I/O ports at 9c00 [size=8]
I/O ports at 9800 [size=8]
Memory at fcffb000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [48] Power Management version 2
Kernel driver in use: serial
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit eafbe67f84,
n_tty: Refactor input_available_p() by call site
broke poll() when TIME_CHAR(tty) and MIN_CHAR(tty) are both 0.
When TIME_CHAR and MIN_CHAR are both 0, input is available if the
read_cnt is 1 (not 0).
Reported-by: Eric Dumazet <edumazet@google.com>
Tested-by: Eric Dumazet <edumazet@google.com>
Reported-by: Stephane Eranian <eranian@google.com>
Tested-by: David Ahern <dsahern@gmail.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the gpio is not yet available we better also
defer the probing in the rs485 case.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_PM will be set if either or both CONFIG_PM_SLEEP and
CONFIG_PM_RUNTIME is set. Compiling the driver with !CONFIG_PM_SLEEP causes
following compilation warnings:
drivers/tty/serial/8250/8250_dw.c:404:12: warning: ‘dw8250_suspend’ defined but not used [-Wunused-function]
drivers/tty/serial/8250/8250_dw.c:413:12: warning: ‘dw8250_resume’ defined but not used [-Wunused-function]
Fix this by using CONFIG_PM_SLEEP instead.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the info message about a missing wakeirq for uart is printed
every time the serial driver's startup function is called. This happens
multiple times and not just once.
This can cause lots of extra messages at boot time, slowing things down. It is
caused by commit 2a0b965cfb (serial: omap: Add support for optional wake-up)
which was applied for v3.13-rc1.
This patch moves the infomessage to the probe function to display it
only once.
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: stable <stable@vger.kernel.org> # 3.13
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds devicetree support for the MAX310X serial driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes some unused definitions from driver code and
sort #includes alphabetically.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for RS-485 (TIOCSRS485/TIOCGRS485) IOCTLs.
As a result this patch eliminate private driver header.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Always register GPIOs and use dynamic GPIO ID assignment.
This is no much worth if GPIOs is not used, but helps remove
private driver header and add DT support in the future.
Additionally, patch adds missing uart_unregister_driver()
call if probe() fails.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes "frequency" parameter from MAX310X platform_data
and uses CLK API for getting clock. Clock type (XTAL/OSC) is
determined by clk name.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patch move all SPI-dependent stuff in one place. This include move
PM-function definitions out of CONFIG_SPI_MASTER and move regmap
initialization out of common probe into CONFIG_SPI_MASTER which
may help to add I2C support in the future for this driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since 93abe8e4 (clk: add non CONFIG_HAVE_CLK routines) code using clk.h
like this driver needs not depend on HAVE_CLK.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes excess IRQ checks at driver probe().
IRQ validation is already provided by request_threaded_irq().
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch replaces loopback mode support from platform data to
dynamic setup with TIOCMSET ioctl.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Serial core calls set_termios() after port startup, so there are
no reason to setup port twice.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These callbacks were previously used for the IC power initialization.
If this initialization will be needed in the future, it should be
implemented with the regulator API.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch provide more precisely setup of baud rate generator.
If the result of division has a remainder, we use the multiplier
for the base frequency. Additionally, we report result baud rate
back to serial core.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hardware supported by the driver is only found on SUPERH or
ARCH_SHMOBILE platforms. Restrict non-COMPILE_TEST compilation to them.
Cc: linux-serial@vger.kernel.org
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add CONFIG_DEBUG_FS to 'char name' in order to fix the following
build warning, because 'char name' is used only when CONFIG_DEBUG_FS
is enabled.
drivers/tty/serial/pch_uart.c:1765:7: warning: unused variable 'name' [-Wunused-variable]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the following compile warning about cast to pointer from
integer of different size.
drivers/tty/serial/sh-sci.c:2021:19: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the info message about a missing wakeirq for uart is printed
every time the serial driver's startup function is called. This happens
multiple times and not just once.
This patch moves the infomessage to the probe function to display it
only once.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement the polling functionality for the MSM serial driver.
This allows us to use KGDB on this hardware.
Cc: David Brown <davidb@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "int check" argument of lock_acquire() and held_lock->check are
misleading. This is actually a boolean: 2 means "true", everything
else is "false".
And there is no need to pass 1 or 0 to lock_acquire() depending on
CONFIG_PROVE_LOCKING, __lock_acquire() checks prove_locking at the
start and clears "check" if !CONFIG_PROVE_LOCKING.
Note: probably we can simply kill this member/arg. The only explicit
user of check => 0 is rcu_lock_acquire(), perhaps we can change it to
use lock_acquire(trylock =>, read => 2). __lockdep_no_validate means
check => 0 implicitly, but we can change validate_chain() to check
hlock->instance->key instead. Not to mention it would be nice to get
rid of lockdep_set_novalidate_class().
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Dave Jones <davej@redhat.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20140120182006.GA26495@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The 'active' sysfs attribute should refer to the currently active tty
devices the console is running on, not the currently active console.
The console structure doesn't refer to any device in sysfs, only the tty
the console is running on has. So we need to print out the tty names in
'active', not the console names.
This resolves an issue on s390 platforms in determining the correct
console device to use.
Cc: Lennart Poettering <lennart@poettering.net>
Cc: Kay Sievers <kay@vrfy.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Werner Fink <werner@suse.de>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
3GPP TS 07.10 states in section 5.4.6.3.7:
"The length byte contains the value 2 or 3 ... depending on the break
signal." The break byte is optional and if it is sent, the length is
3. In fact the driver was not able to work with modems that send this
break byte in their modem status control message. If the modem just
sends the break byte if it is really set, then weird things might
happen.
The code for deconding the modem status to the internal linux
presentation in gsm_process_modem has already a big comment about
this 2 or 3 byte length thing and it is already able to decode the
brk, but the code calling the gsm_process_modem function in
gsm_control_modem does not encode it and hand it over the right way.
This patch fixes this.
Without this fix if the modem sends the brk byte in it's modem status
control message the driver will hang when opening a muxed channel.
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The HVC_OPAL/RTAS/UDBG/XEN options are all bool, and hence their support
is either present or absent. It will never be modular, so using
module_init as an alias for __initcall is rather misleading.
Fix this up now, so that we can relocate module_init from
init.h into module.h in the future. If we don't do this, we'd
have to add module.h to obviously non-modular code, and that
would be a worse thing.
Note that direct use of __initcall is discouraged, vs. one
of the priority categorized subgroups. As __initcall gets
mapped onto device_initcall, our use of device_initcall
directly in this change means that the runtime impact is
zero -- it will remain at level 6 in initcall ordering.
Also the __exitcall functions have been outright deleted since
they are only ever of interest to UML, and UML will never be
using any of this code.
Cc: Richard Weinberger <richard@nod.at>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We've split Qualcomm MSM support into legacy and multiplatform. So add
the ability to build the serial driver on the newer ARCH_QCOM
multiplatform.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Pull MIPS updates from Ralf Baechle:
"The most notable new addition inside this pull request is the support
for MIPS's latest and greatest core called "inter/proAptiv". The
patch series describes this core as follows.
"The interAptiv is a power-efficient multi-core microprocessor
for use in system-on-chip (SoC) applications. The interAptiv combines
a multi-threading pipeline with a coherence manager to deliver improved
computational throughput and power efficiency. The interAptiv can
contain one to four MIPS32R3 interAptiv cores, system level
coherence manager with L2 cache, optional coherent I/O port,
and optional floating point unit."
The platform specific patches touch all 3 Broadcom families. It adds
support for the new Broadcom/Netlogix XLP9xx Soc, building a common
BCM63XX SMP kernel for all BCM63XX SoCs regardless of core type/count
and full gpio button/led descriptions for BCM47xx.
The rest of the series are cleanups and bug fixes that are MIPS
generic and consist largely of changes that Imgtec/MIPS had published
in their linux-mti-3.10.git stable tree. Random other cleanups and
patches preparing code to be merged in 3.15"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (139 commits)
mips: select ARCH_MIGHT_HAVE_PC_SERIO
mips: delete non-required instances of include <linux/init.h>
MIPS: KVM: remove shadow_tlb code
MIPS: KVM: use common EHINV aware UNIQUE_ENTRYHI
mips/ide: flush dcache also if icache does not snoop dcache
MIPS: BCM47XX: fix position of cpu_wait disabling
MIPS: BCM63XX: select correct MIPS_L1_CACHE_SHIFT value
MIPS: update MIPS_L1_CACHE_SHIFT based on MIPS_L1_CACHE_SHIFT_<N>
MIPS: introduce MIPS_L1_CACHE_SHIFT_<N>
MIPS: ZBOOT: gather string functions into string.c
arch/mips/pci: don't check resource with devm_ioremap_resource
arch/mips/lantiq/xway: don't check resource with devm_ioremap_resource
bcma: gpio: don't cast u32 to unsigned long
ssb: gpio: add own IRQ domain
MIPS: BCM47XX: fix sparse warnings in board.c
MIPS: BCM47XX: add board detection for Linksys WRT54GS V1
MIPS: BCM47XX: fix detection for some boards
MIPS: BCM47XX: Enable buttons support on SSB
MIPS: BCM47XX: Convert WNDR4500 to new syntax
MIPS: BCM47XX: Use "timer" trigger for status LEDs
...
Pull more powerpc bits from Ben Herrenschmidt:
"Here are a few more powerpc bits for this merge window. The bulk is
made of two pull requests from Scott and Anatolij that I had missed
previously (they arrived while I was away). Since both their branches
are in -next independently, and the content has been around for a
little while, they can still go in.
The rest is mostly bug and regression fixes, a small series of
cleanups to our pseries cpuidle code (including moving it to the right
place), and one new cpuidle bakend for the powernv platform. I also
wired up the new sched_attr syscalls"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (37 commits)
powerpc: Wire up sched_setattr and sched_getattr syscalls
powerpc/hugetlb: Replace __get_cpu_var with get_cpu_var
powerpc: Make sure "cache" directory is removed when offlining cpu
powerpc/mm: Fix mmap errno when MAP_FIXED is set and mapping exceeds the allowed address space
powerpc/powernv/cpuidle: Back-end cpuidle driver for powernv platform.
powerpc/pseries/cpuidle: smt-snooze-delay cleanup.
powerpc/pseries/cpuidle: Remove MAX_IDLE_STATE macro.
powerpc/pseries/cpuidle: Make cpuidle-pseries backend driver a non-module.
powerpc/pseries/cpuidle: Use cpuidle_register() for initialisation.
powerpc/pseries/cpuidle: Move processor_idle.c to drivers/cpuidle.
powerpc: Fix 32-bit frames for signals delivered when transactional
powerpc/iommu: Fix initialisation of DART iommu table
powerpc/numa: Fix decimal permissions
powerpc/mm: Fix compile error of pgtable-ppc64.h
powerpc: Fix hw breakpoints on !HAVE_HW_BREAKPOINT configurations
clk: corenet: Adds the clock binding
powerpc/booke64: Guard e6500 tlb handler with CONFIG_PPC_FSL_BOOK3E
powerpc/512x: dts: add MPC5125 clock specs
powerpc/512x: clk: support MPC5121/5123/5125 SoC variants
powerpc/512x: clk: enforce even SDHC divider values
...
<<
Switch mpc512x to the common clock framework and adapt mpc512x
drivers to use the new clock driver. Old PPC_CLOCK code is
removed entirely since there are no users any more.
>>
Here are tiny and assorted serial driver fixes that have been in a
branch in my tree for a while and somehow did not get properly merged
into my big TTY / Serial pull request for 3.14-rc1. Sorry about that.
All have been in linux-next for a while with no issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlLm74UACgkQMUfUDdst+ylviACcC4eubO3yOgJzG5A69+Ncl7t6
sy0An2Kb3x0evfvmR6O+fT67rFrvBijA
=Iv/6
-----END PGP SIGNATURE-----
Merge tag 'tty-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull serial fixes from Greg KH:
"Here are tiny and assorted serial driver fixes that have been in a
branch in my tree for a while and somehow did not get properly merged
into my big TTY / Serial pull request for 3.14-rc1. Sorry about that.
All have been in linux-next for a while with no issues"
* tag 'tty-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: xuartps: Properly guard sysrq specific code
serial: 8250: Fix initialisation of Quatech cards with the AMCC PCI chip
serial: icom: dereference after free in load_code()
serial: 8250_dw: add new ACPI IDs
tty: serial: pch: don't crash if DMA enabled but not loaded
serial: samsung: move clock deactivation below uart registration
Pull s390 patches from Martin Schwidefsky:
"A new binary interface to be able to query and modify the LPAR
scheduler weight and cap settings. Some improvements for the hvc
terminal over iucv and a couple of bux fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/hypfs: add interface for diagnose 0x304
s390: wire up sys_sched_setattr/sys_sched_getattr
s390/uapi: fix struct statfs64 definition
s390/uaccess: remove dead extern declarations, make functions static
s390/uaccess: test if current->mm is set before walking page tables
s390/zfcpdump: make zfcpdump depend on 64BIT
s390/32bit: fix cmpxchg64
s390/xpram: don't modify module parameters
s390/zcrypt: remove zcrypt kmsg documentation again
s390/hvc_iucv: Automatically assign free HVC terminal devices
s390/hvc_iucv: Display connection details through device attributes
s390/hvc_iucv: fix sparse warning
s390/vmur: Link parent CCW device during UR device creation
Pull powerpc updates from Ben Herrenschmidt:
"So here's my next branch for powerpc. A bit late as I was on vacation
last week. It's mostly the same stuff that was in next already, I
just added two patches today which are the wiring up of lockref for
powerpc, which for some reason fell through the cracks last time and
is trivial.
The highlights are, in addition to a bunch of bug fixes:
- Reworked Machine Check handling on kernels running without a
hypervisor (or acting as a hypervisor). Provides hooks to handle
some errors in real mode such as TLB errors, handle SLB errors,
etc...
- Support for retrieving memory error information from the service
processor on IBM servers running without a hypervisor and routing
them to the memory poison infrastructure.
- _PAGE_NUMA support on server processors
- 32-bit BookE relocatable kernel support
- FSL e6500 hardware tablewalk support
- A bunch of new/revived board support
- FSL e6500 deeper idle states and altivec powerdown support
You'll notice a generic mm change here, it has been acked by the
relevant authorities and is a pre-req for our _PAGE_NUMA support"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (121 commits)
powerpc: Implement arch_spin_is_locked() using arch_spin_value_unlocked()
powerpc: Add support for the optimised lockref implementation
powerpc/powernv: Call OPAL sync before kexec'ing
powerpc/eeh: Escalate error on non-existing PE
powerpc/eeh: Handle multiple EEH errors
powerpc: Fix transactional FP/VMX/VSX unavailable handlers
powerpc: Don't corrupt transactional state when using FP/VMX in kernel
powerpc: Reclaim two unused thread_info flag bits
powerpc: Fix races with irq_work
Move precessing of MCE queued event out from syscall exit path.
pseries/cpuidle: Remove redundant call to ppc64_runlatch_off() in cpu idle routines
powerpc: Make add_system_ram_resources() __init
powerpc: add SATA_MV to ppc64_defconfig
powerpc/powernv: Increase candidate fw image size
powerpc: Add debug checks to catch invalid cpu-to-node mappings
powerpc: Fix the setup of CPU-to-Node mappings during CPU online
powerpc/iommu: Don't detach device without IOMMU group
powerpc/eeh: Hotplug improvement
powerpc/eeh: Call opal_pci_reinit() on powernv for restoring config space
powerpc/eeh: Add restore_config operation
...
Updates of SoC-near drivers and other driver updates that makes more sense to
take through our tree.
The largest part of this is a conversion of device registration for some
renesas shmobile/sh devices over to use resources. This has required
coordination with the corresponding arch/sh changes, and we've agreed
to merge the arch/sh changes through our tree.
Added in this branch is support for Trusted Foundations secure firmware,
which is what is used on many of the commercial Nvidia Tegra products
that are in the market, including the Nvidia Shield. The code is local
to arch/arm at this time since it's uncertain whether it will be shared
with arm64 longer-term, if needed we will refactor later.
A couple of new RTC drivers used on ARM boards, merged through our tree
on request by the RTC maintainer.
... plus a bunch of smaller updates across the board, gpio conversions
for davinci, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=JJlw
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM driver updates from Olof Johansson:
"Updates of SoC-near drivers and other driver updates that makes more
sense to take through our tree.
The largest part of this is a conversion of device registration for
some renesas shmobile/sh devices over to use resources. This has
required coordination with the corresponding arch/sh changes, and
we've agreed to merge the arch/sh changes through our tree.
Added in this branch is support for Trusted Foundations secure
firmware, which is what is used on many of the commercial Nvidia Tegra
products that are in the market, including the Nvidia Shield. The
code is local to arch/arm at this time since it's uncertain whether it
will be shared with arm64 longer-term, if needed we will refactor
later.
A couple of new RTC drivers used on ARM boards, merged through our
tree on request by the RTC maintainer.
... plus a bunch of smaller updates across the board, gpio conversions
for davinci, etc"
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (45 commits)
watchdog: davinci: rename platform driver to davinci-wdt
tty: serial: Limit msm_serial_hs driver to platforms that use it
mmc: msm_sdcc: Limit driver to platforms that use it
usb: phy: msm: Move mach dependent code to platform data
clk: versatile: fixup IM-PD1 clock implementation
clk: versatile: pass a name to ICST clock provider
ARM: integrator: pass parent IRQ to the SIC
irqchip: versatile FPGA: support cascaded interrupts from DT
gpio: davinci: don't create irq_domain in case of unbanked irqs
gpio: davinci: use chained_irq_enter/chained_irq_exit API
gpio: davinci: add OF support
gpio: davinci: remove unused variable intc_irq_num
gpio: davinci: convert to use irqdomain support.
gpio: introduce GPIO_DAVINCI kconfig option
gpio: davinci: get rid of DAVINCI_N_GPIO
gpio: davinci: use {readl|writel}_relaxed() instead of __raw_*
serial: sh-sci: Add OF support
serial: sh-sci: Add device tree bindings documentation
serial: sh-sci: Remove platform data mapbase and irqs fields
serial: sh-sci: Remove platform data scbrr_algo_id field
...
This is the branch where we usually queue up cleanup efforts, moving
drivers out of the architecture directory, header file restructuring,
etc. Sometimes they tangle with new development so it's hard to keep it
strictly to cleanups.
Some of the things included in this branch are:
* Atmel SAMA5 conversion to common clock
* Reset framework conversion for tegra platforms
- Some of this depends on tegra clock driver reworks that are shared with Mike
Turquette's clk tree.
* Tegra DMA refactoring, which are shared branches with the DMA tree.
* Removal of some header files on exynos to prepare for multiplatform
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=3CcT
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This is the branch where we usually queue up cleanup efforts, moving
drivers out of the architecture directory, header file restructuring,
etc. Sometimes they tangle with new development so it's hard to keep
it strictly to cleanups.
Some of the things included in this branch are:
* Atmel SAMA5 conversion to common clock
* Reset framework conversion for tegra platforms
- Some of this depends on tegra clock driver reworks that are shared
with Mike Turquette's clk tree.
* Tegra DMA refactoring, which are shared branches with the DMA tree.
* Removal of some header files on exynos to prepare for
multiplatform"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (169 commits)
ARM: mvebu: move Armada 370/XP specific definitions to armada-370-xp.h
ARM: mvebu: remove prototypes of non-existing functions from common.h
ARM: mvebu: move ARMADA_XP_MAX_CPUS to armada-370-xp.h
serial: sh-sci: Rework baud rate calculation
serial: sh-sci: Compute overrun_bit without using baud rate algo
serial: sh-sci: Remove unused GPIO request code
serial: sh-sci: Move overrun_bit and error_mask fields out of pdata
serial: sh-sci: Support resources passed through platform resources
serial: sh-sci: Don't check IRQ in verify port operation
serial: sh-sci: Set the UPF_FIXED_PORT flag
serial: sh-sci: Remove duplicate interrupt check in verify port op
serial: sh-sci: Simplify baud rate calculation algorithms
serial: sh-sci: Remove baud rate calculation algorithm 5
serial: sh-sci: Sort headers alphabetically
ARM: EXYNOS: Kill exynos_pm_late_initcall()
ARM: EXYNOS: Consolidate selection of PM_GENERIC_DOMAINS for Exynos4
ARM: at91: switch Calao QIL-A9260 board to DT
clk: at91: fix pmc_clk_ids data type attriubte
PM / devfreq: use inclusion <mach/map.h> instead of <plat/map-s5p.h>
ARM: EXYNOS: remove <mach/regs-clock.h> for exynos
...
Pull audit update from Eric Paris:
"Again we stayed pretty well contained inside the audit system.
Venturing out was fixing a couple of function prototypes which were
inconsistent (didn't hurt anything, but we used the same value as an
int, uint, u32, and I think even a long in a couple of places).
We also made a couple of minor changes to when a couple of LSMs called
the audit system. We hoped to add aarch64 audit support this go
round, but it wasn't ready.
I'm disappearing on vacation on Thursday. I should have internet
access, but it'll be spotty. If anything goes wrong please be sure to
cc rgb@redhat.com. He'll make fixing things his top priority"
* git://git.infradead.org/users/eparis/audit: (50 commits)
audit: whitespace fix in kernel-parameters.txt
audit: fix location of __net_initdata for audit_net_ops
audit: remove pr_info for every network namespace
audit: Modify a set of system calls in audit class definitions
audit: Convert int limit uses to u32
audit: Use more current logging style
audit: Use hex_byte_pack_upper
audit: correct a type mismatch in audit_syscall_exit()
audit: reorder AUDIT_TTY_SET arguments
audit: rework AUDIT_TTY_SET to only grab spin_lock once
audit: remove needless switch in AUDIT_SET
audit: use define's for audit version
audit: documentation of audit= kernel parameter
audit: wait_for_auditd rework for readability
audit: update MAINTAINERS
audit: log task info on feature change
audit: fix incorrect set of audit_sock
audit: print error message when fail to create audit socket
audit: fix dangling keywords in audit_log_set_loginuid() output
audit: log on errors from filter user rules
...
Now that the UART block defines have been moved to a separate file,
include that one and do not longer rely on the MIPS-specific
bcm63xx_regs.h header file.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6204/
bcm_{readl,writel} macros expand to __raw_{readl,writel}, use these
directly such that we do not rely on the platform to provide these for
us. As a result, we no longer use bcm63xx_io.h, so remove that inclusion
too.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6201/
bcm63xx_irqs.h is included but we are not using anything from it, drop
that include.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6205/
Pull trivial tree updates from Jiri Kosina:
"Usual rocket science stuff from trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
neighbour.h: fix comment
sched: Fix warning on make htmldocs caused by wait.h
slab: struct kmem_cache is protected by slab_mutex
doc: Fix typo in USB Gadget Documentation
of/Kconfig: Spelling s/one/once/
mkregtable: Fix sscanf handling
lp5523, lp8501: comment improvements
thermal: rcar: comment spelling
treewide: fix comments and printk msgs
IXP4xx: remove '1 &&' from a condition check in ixp4xx_restart()
Documentation: update /proc/uptime field description
Documentation: Fix size parameter for snprintf
arm: fix comment header and macro name
asm-generic: uaccess: Spelling s/a ny/any/
mtd: onenand: fix comment header
doc: driver-model/platform.txt: fix a typo
drivers: fix typo in DEVTMPFS_MOUNT Kconfig help text
doc: Fix typo (acces_process_vm -> access_process_vm)
treewide: Fix typos in printk
drivers/gpu/drm/qxl/Kconfig: reformat the help text
...
This was a "forgotten" branch of tty fixes that somehow didn't make it
into my "main" branches, my fault.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the generic "lnxhvc" terminal ID to automatically assign a HVC terminal when
connecting to the HVC IUCV terminal device driver. The terminal device driver
tries to find a free (not connected) HVC terminal to satisfy the incoming
connection request.
With this improvement, you do not longer need to guess which HVC terminal is
free, that is, not connected. Also you can still connect to a particular HVC
terminal by using its associated terminal ID.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add device attributes to display details about the connection status
of HVC IUCV terminals.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
drivers/tty/hvc/hvc_iucv.c:131:25: warning: symbol 'hvc_iucv_get_private' was not
declared. Should it be static?
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Right now the sessionid value in the kernel is a combination of u32,
int, and unsigned int. Just use unsigned int throughout.
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
The uart timer will schedule a tasklet when it fires. It is possible that it
can fire inside _shutdown before it is killed in the dma and pdc cleanup
routines. This causes a tasklet that exists after the port is shutdown, so when
the kernel finally executes it, it panics as the tty port is NULL.
This is a somewhat rare condition but its possible if a program keeps on
opening/closing the port. It has been observed in particular with systemd
boot messages that were causing a kernel panic because of this behavior.
Moving the timer deletion to the beginning of the function stops a tasklet from
being scheduled unexpectedly.
Signed-off-by: Marek Roszko <mark.roszko@gmail.com>
Cc: stable <stable@vger.kernel.org> # v3.12
[nicolas.ferre@atmel.com: modify commit message, call setup_timer() in any case]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
prepare and enable the FIFO clock upon PSC FIFO initialization,
check for and propagage errors when enabling the PSC FIFO clock,
disable and unprepare the FIFO clock upon PSC FIFO uninitialization
devm_{get,put}_clk() doesn't apply here, as the SoC provides a
single FIFO component which is shared among several PSC components,
thus the FIFO isn't associated with a device (while the PSCs are)
provide a fallback clock lookup approach in case the OF based clock
lookup for the PSC FIFO fails, this allows for successful operation in
the presence of an outdated device tree which lacks clock specs
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
after device tree based clock lookup became available, the peripheral
driver need no longer construct clock names which include the PSC index,
remove the "psc%d_mclk" template and unconditionally use 'mclk'
acquire and release the "ipg" clock item for register access as well
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
ehv_bytechan is marked tristate but fails to build as a module:
drivers/tty/ehv_bytechan.c:363:1: error: type defaults to ‘int’ in declaration of ‘console_initcall’ [-Werror=implicit-int]
It doesn't make much sense for a console driver to be built as
a module, so change it to a bool.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Scott Wood <scottwood@freescale.com>
* qcom/drivers:
tty: serial: Limit msm_serial_hs driver to platforms that use it
mmc: msm_sdcc: Limit driver to platforms that use it
usb: phy: msm: Move mach dependent code to platform data
Signed-off-by: Olof Johansson <olof@lixom.net>
The msm_serial_hs driver uses mach specific dma APIs. This is not
compatible with the multi-platform ARM effort. Let's only compile
this driver on MSM devices that are prepared to support it;
allowing the DT based MSM devices to enter the multi-platform ARM
build.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Tegra chips have 4 or 5 identical UART modules embedded. UARTs C..E have
their MODEM-control signals tied off to a static state. However UARTs A
and B can optionally route those signals to/from package pins, depending
on the exact pinmux configuration.
When these signals are not routed to package pins, false interrupts may
trigger either temporarily, or permanently, all while not showing up in
the IIR; it will read as NO_INT. This will eventually lead to the UART
IRQ being disabled due to unhandled interrupts. When this happens, the
kernel may print e.g.:
irq 68: nobody cared (try booting with the "irqpoll" option)
In order to prevent this, enable UART_BUG_NOMSR. This prevents
UART_IER_MSI from being enabled, which prevents the false interrupts
from triggering.
In practice, this is not needed under any of the following conditions:
* On Tegra chips after Tegra30, since the HW bug has apparently been
fixed.
* On UARTs C..E since their MODEM control signals are tied to the correct
static state which doesn't trigger the issue.
* On UARTs A..B if the MODEM control signals are routed out to package
pins, since they will then carry valid signals.
However, we ignore these exceptions for now, since they are only relevant
if a board actually hooks up more than a 4-wire UART, and no currently
supported board does this. If we ever support a board that does, we can
refine the algorithm that enables UART_BUG_NOMSR to take those exceptions
into account, and/or read a flag from DT/... that indicates that the
board has hooked up and pinmux'd more than a 4-wire UART.
Reported-by: Olof Johansson <olof@lixom.net> # autotester
Cc: <stable@vger.kernel.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using RX DMA, the driver won't pass any data to the uart layer
until the buffer is flipped. When the port is shutdown, the dma buffers
are unmapped, but the head and tail of the ring buffer are not reseted.
Since the serial console will keep the port open, this will only
present itself when the uart is not shared.
To reproduce the issue, with an unpatched driver, run a getty on /dev/ttyS0
with no serial console and exit. Getty will exit, and when the new one returns
you will be unable to log in. If you hold down a key long enough to fill the
DMA buffer and flip it, you can then log in.
Signed-off-by: Mark Deneen <mdeneen@gmail.com>
Acked-by: Leilei Zhao <leilei.zhao@atmel.com>
[nicolas.ferre@atmel.com: adapt to mainline kernel, handle !DMA case]
Cc: <stable@vger.kernel.org> # v3.12
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The _remove callback could be called when a tasklet is scheduled. tasklet_kill
was called inside the function in order to free up any scheduled tasklets.
However it was called after uart_remove_one_port which destroys tty references
needed in the port for atmel_tasklet_func.
Simply putting the tasklet_kill at the start of the function will prevent this
conflict.
Signed-off-by: Marek Roszko <mark.roszko@gmail.com>
Acked-by: Leilei Zhao <leilei.zhao@atmel.com>
Cc: <stable@vger.kernel.org> # v3.12
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Interrupts were being cleaned up late in the shutdown handler, it is possible
that an interrupt can occur and schedule a tasklet that runs after the port is
cleaned up. There is a null dereference due to this race condition with the
following stacktrace:
[<c02092b0>] (atmel_tasklet_func+0x514/0x814) from [<c001fd34>] (tasklet_action+0x70/0xa8)
[<c001fd34>] (tasklet_action+0x70/0xa8) from [<c001f60c>] (__do_softirq+0x90/0x144)
[<c001f60c>] (__do_softirq+0x90/0x144) from [<c001fa18>] (irq_exit+0x40/0x4c)
[<c001fa18>] (irq_exit+0x40/0x4c) from [<c000e298>] (handle_IRQ+0x64/0x84)
[<c000e298>] (handle_IRQ+0x64/0x84) from [<c000d6c0>] (__irq_svc+0x40/0x50)
[<c000d6c0>] (__irq_svc+0x40/0x50) from [<c0208060>] (atmel_rx_dma_release+0x88/0xb8)
[<c0208060>] (atmel_rx_dma_release+0x88/0xb8) from [<c0209740>] (atmel_shutdown+0x104/0x160)
[<c0209740>] (atmel_shutdown+0x104/0x160) from [<c0205e8c>] (uart_port_shutdown+0x2c/0x38)
Signed-off-by: Marek Roszko <mark.roszko@gmail.com>
Acked-by: Leilei Zhao <leilei.zhao@atmel.com>
Cc: <stable@vger.kernel.org> # v3.12
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In rx dma-callback it calls tasklet_schedule, if the tasklet
be scheduled after all the dma-callback in the rx dma channel,
current check condition in the tasklet will not do fetch dma
buffer into tty because tx_issued is equal with tx_completed,
so as timeout tasklet does.
so we check whether we should fetch the whole dma buffer into
tty according to the status of transactions in rx dma channel.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
this patch provides PM entry of uart_ops, then drop clk enable and
disable because serial core will do it.
the patch also fixes the issue that uart hang in resume caused by
not-enabled clock.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
use SET_SYSTEM_SLEEP_PM_OPS to initialize suspend/resume functions
instead of legacy suspend and resume entries of platform_driver.
this will add hibernation support automatically as suspend to disk
entries are also set.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This helps increasing build testing coverage.
To do this, read{write}_relaxed() functions was be replaced with
simple read{write}() variants. Potential "uninitialized variable"
warnings was be fixed if driver compiled without MFD_SYSCON.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch replace custom handling of IrDA feature with N_IRDA
line discipline, so IrDA mode can be used with irtty driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The four variants of the synclink driver use the same code in their
open() callback to wait for a port in process of being closed,
using interruptible_sleep_on, which is racy and going away soon.
Making things worse, these functions hold the BTM while doing so,
which means that if we ever enter this code path, we cannot actually
continue since the other thread that is in process of closing the
port can no longer get the BTM.
This addresses both issues by using wait_event_interruptible_tty()
instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
interruptible_sleep_on is generally problematic and we want to get
rid of it. In case of TIOCMIWAIT, that race is actually in user
space and does not get fixed since we can only detect changes after
entering the ioctl handler, but it removes one more caller.
This instance can not be trivially replaced with wait_event, so
I chose to open-code the wait loop using prepare_to_wait/finish_wait.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixed several typo in printk from various
part of kernel source.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
---------------------------
This pull request contains updates
to DaVinci GPIO driver and the
resultant platform code changes. The
updates include DT-conversion and
changes to make the driver cross-platform
ready.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=DxLt
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v3.14/gpio' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/drivers
From Sekhar Nori:
DaVinci GPIO driver updates
---------------------------
This pull request contains updates to DaVinci GPIO driver and the
resultant platform code changes. The updates include DT-conversion and
changes to make the driver cross-platform ready.
* tag 'davinci-for-v3.14/gpio' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
gpio: davinci: don't create irq_domain in case of unbanked irqs
gpio: davinci: use chained_irq_enter/chained_irq_exit API
gpio: davinci: add OF support
gpio: davinci: remove unused variable intc_irq_num
gpio: davinci: convert to use irqdomain support.
gpio: introduce GPIO_DAVINCI kconfig option
gpio: davinci: get rid of DAVINCI_N_GPIO
gpio: davinci: use {readl|writel}_relaxed() instead of __raw_*
Signed-off-by: Olof Johansson <olof@lixom.net>
* Add Device Tree Support
* Remove platform data mapbase and irqs fields
* Remove platform data scbrr_algo_id field
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=IZCI
-----END PGP SIGNATURE-----
Merge tag 'renesas-sh-sci3-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/drivers
From Simon Horman:
Third Round of Renesas SH SCI Updates for v3.14
* Add Device Tree Support
* Remove platform data mapbase and irqs fields
* Remove platform data scbrr_algo_id field
* tag 'renesas-sh-sci3-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
serial: sh-sci: Add OF support
serial: sh-sci: Add device tree bindings documentation
serial: sh-sci: Remove platform data mapbase and irqs fields
serial: sh-sci: Remove platform data scbrr_algo_id field
Signed-off-by: Olof Johansson <olof@lixom.net>
* Rework baud rate calculation
* Compute overrun_bit without using baud rate algo
* Remove unused GPIO request code
* Move overrun_bit and error_mask fields out of pdata
* Support resources passed through platform resources
* Don't check IRQ in verify port operation
* Set the UPF_FIXED_PORT flag
* Remove duplicate interrupt check in verify port op
* Simplify baud rate calculation algorithms
* Remove baud rate calculation algorithm 5
* Sort headers alphabetically
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=BQSn
-----END PGP SIGNATURE-----
Merge tag 'renesas-sh-sci2-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/cleanup
From Simon Horman:
Second Round of Renesas SH SCI updates for v3.14
* Rework baud rate calculation
* Compute overrun_bit without using baud rate algo
* Remove unused GPIO request code
* Move overrun_bit and error_mask fields out of pdata
* Support resources passed through platform resources
* Don't check IRQ in verify port operation
* Set the UPF_FIXED_PORT flag
* Remove duplicate interrupt check in verify port op
* Simplify baud rate calculation algorithms
* Remove baud rate calculation algorithm 5
* Sort headers alphabetically
* tag 'renesas-sh-sci2-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
serial: sh-sci: Rework baud rate calculation
serial: sh-sci: Compute overrun_bit without using baud rate algo
serial: sh-sci: Remove unused GPIO request code
serial: sh-sci: Move overrun_bit and error_mask fields out of pdata
serial: sh-sci: Support resources passed through platform resources
serial: sh-sci: Don't check IRQ in verify port operation
serial: sh-sci: Set the UPF_FIXED_PORT flag
serial: sh-sci: Remove duplicate interrupt check in verify port op
serial: sh-sci: Simplify baud rate calculation algorithms
serial: sh-sci: Remove baud rate calculation algorithm 5
serial: sh-sci: Sort headers alphabetically
Signed-off-by: Olof Johansson <olof@lixom.net>
Updates for the SH SCI serial driver
* Convert to clk_prepare/unprepare
* Fix warnings due to improper casts and printk formats
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=pxvs
-----END PGP SIGNATURE-----
Merge tag 'renesas-sh-sci-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/cleanup
From Simon Horman:
Renesas SH SCI updates for v3.14
Updates for the SH SCI serial driver
* Convert to clk_prepare/unprepare
* Fix warnings due to improper casts and printk formats
* tag 'renesas-sh-sci-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
serial: sh-sci: Convert to clk_prepare/unprepare
serial: sh-sci: Don't enable/disable port from within break timer
serial: sh-sci: Fix warnings due to improper casts and printk formats
Signed-off-by: Olof Johansson <olof@lixom.net>
This series converts the Tegra DTs and drivers to use the common/
standard DMA and reset bindings, rather than custom bindings. It also
adds complete documentation for the Tegra clock bindings without
actually changing any binding definitions.
This conversion relies on a few sets of patches in branches from outside
the Tegra tree:
1) A patch to add an DMA channel request API which allows deferred probe
to be implemented.
2) A patch to implement a common part of the of_xlate function for DMA
controllers.
3) Some ASoC patches (which in turn rely on (1) above), which support
deferred probe during DMA channel allocation.
4) The Tegra clock driver changes for 3.14.
Consequently, this branch is based on a merge of all of those external
branches.
In turn, this branch is or will be pulled into a few places that either
rely on features introduced here, or would otherwise conflict with the
patches:
a) Tegra's own for-3.14/powergate and for-4.14/dt branches, to avoid
conflicts.
b) The DRM tree, which introduces new code that relies on the reset
controller framework introduced in this branch, and to avoid
conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=8T7+
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.14-dmas-resets-rework' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/cleanup
From Stephen Warren:
ARM: tegra: implement common DMA and resets DT bindings
This series converts the Tegra DTs and drivers to use the common/
standard DMA and reset bindings, rather than custom bindings. It also
adds complete documentation for the Tegra clock bindings without
actually changing any binding definitions.
This conversion relies on a few sets of patches in branches from outside
the Tegra tree:
1) A patch to add an DMA channel request API which allows deferred probe
to be implemented.
2) A patch to implement a common part of the of_xlate function for DMA
controllers.
3) Some ASoC patches (which in turn rely on (1) above), which support
deferred probe during DMA channel allocation.
4) The Tegra clock driver changes for 3.14.
Consequently, this branch is based on a merge of all of those external
branches.
In turn, this branch is or will be pulled into a few places that either
rely on features introduced here, or would otherwise conflict with the
patches:
a) Tegra's own for-3.14/powergate and for-4.14/dt branches, to avoid
conflicts.
b) The DRM tree, which introduces new code that relies on the reset
controller framework introduced in this branch, and to avoid
conflicts.
* tag 'tegra-for-3.14-dmas-resets-rework' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: (30 commits)
spi: tegra: checking for ERR_PTR instead of NULL
ASoC: tegra: update module reset list for Tegra124
clk: tegra: remove bogus PCIE_XCLK
clk: tegra: remove legacy reset APIs
ARM: tegra: remove legacy DMA entries from DT
ARM: tegra: remove legacy clock entries from DT
USB: EHCI: tegra: use reset framework
Input: tegra-kbc - use reset framework
serial: tegra: convert to standard DMA DT bindings
serial: tegra: use reset framework
spi: tegra: convert to standard DMA DT bindings
spi: tegra: use reset framework
staging: nvec: use reset framework
i2c: tegra: use reset framework
ASoC: tegra: convert to standard DMA DT bindings
ASoC: tegra: allocate AHUB FIFO during probe() not startup()
ASoC: tegra: call pm_runtime APIs around register accesses
ASoC: tegra: use reset framework
dma: tegra: register as an OF DMA controller
dma: tegra: use reset framework
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Extend the driver to with support for SCIx device tree bindings. A
minimal set of features is supported, additional properties can be added
later should the need to describe more device features arise.
Signed-off-by: Bastian Hecht <hechtb+renesas@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The fields are not used anymore by board files, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The field isn't set by any board, remote it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Computing the baud rate register value requires knowledge of the
hardware sampling rate. This information is currently encoded in a baud
rate calculation algorithm ID passed through platform data. However, it
can be derived from the port type directly in most cases.
Compute the sampling rate internally in the driver if the baud rate
calculation algorithm ID isn't specified, and allow platforms to
override the sampling rate through platform data in special cases (this
is only required for SCIFA ports on sh7723 and sh7724, the reason needs
to be investigated).
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The overrun bit index is a property of the hardware. It's currently
computed based on a different and unrelated hardware property, the baud
rate calculation algorithm. Compute it using hardware identification
information only.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The driver requests at initialization time GPIOs passed through platform
data. No platform makes use of this feature, remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
None of the fields is ever set by board code, and both of them are set
in the driver at probe time. Move them out of struct plat_sci_port to
struct sci_port.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Memory and IRQ resources are currently passed to the driver through
platform data. Support passing them through the standard platform
resources mechanism instead. This deprecates platform data resources.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The IRQ number can't be modified by the user as the port is fixed.
There's no need to check the new IRQ number as it will be ignored by the
core.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The base address, IRQ and baud rate generator parent clock rate can't be
changed by userspace. Mark the port as fixed.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The driver checks if the interrupt number is greater than nr_irqs and
returns an error in that case. The same check is already performed by
the caller, remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Rewrite the baud rate register value calculations in easier to read
forms. The computed value isn't modified.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
there is an overflow in the code :
cyz_polling_cycle = (arg * HZ) / 1000,
the multiplicator arg comes from user, so it may be an overflow if
arg is a big number. And the value of cyc_polling_cycle will be
wrong when it is used next time.
Reported-by: Qixue Xiao <xiaoqixue_1@163.com>
Suggested-by: Yongjian Xu <xuyongjiande@gmail.com>
Suggested-by: Yu Chen <chyyuu@gmail.com>
Signed-off-by: Qixue Xiao <xiaoqixue_1@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This passes the errata fix using a GPIO to control the RTS pin
on one of the AT91 chips to use gpiolib instead of the
AT91-specific interfaces. Also remove the reliance on
compile-time #defines and the cpu_* check and rely on the
platform passing down the proper GPIO pin through platform
data.
This is a prerequisite for getting rid of the local GPIO
implementation in the AT91 platform and move toward
multiplatform.
The patch also adds device tree support for getting the
RTS GPIO pin from the device tree on DT boot paths.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
New driver for NXP (Philips) UART ICs was introduced in September 2012.
Old driver no longer used anywhere, this patch removes it.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the initialisation of older Quatech serial cards which are fitted with
the AMCC PCI Matchmaker interface chip.
Signed-off-by: Jonathan Woithe (jwoithe@just42.net)
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 'tty: xuartps: Implement BREAK detection, add SYSRQ support'
(0c0c47bc40) introduced sysrq support
without properly guarding sysrq specific code which results in build
errors when sysrq is disabled:
DNAME=KBUILD_STR(xilinx_uartps)" -c -o
drivers/tty/serial/.tmp_xilinx_uartps.o
drivers/tty/serial/xilinx_uartps.c
drivers/tty/serial/xilinx_uartps.c: In function 'xuartps_isr':
drivers/tty/serial/xilinx_uartps.c:247:5: error: 'struct uart_port'
has no member named 'sysrq'
drivers/tty/serial/xilinx_uartps.c:247:5: error: 'struct uart_port'
has no member named 'sysrq'
drivers/tty/serial/xilinx_uartps.c:247:5: error: 'struct uart_port'
has no member named 'sysrq'
make[3]: *** [drivers/tty/serial/xilinx_uartps.o] Error 1
Reported-by: Masanari Iida <standby24x7@gmail.com>
Cc: Vlad Lungu <vlad.lungu@windriver.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With block processing of echoed output, observed output order is still
required. Push completed echoes and echo commands prior to output.
Introduce echo_mark echo buffer index, which tracks completed echo
commands; ie., those submitted via commit_echoes but which may not
have been committed. Ensure that completed echoes are output prior
to subsequent terminal writes in process_echoes().
Fixes newline/prompt output order in cooked mode shell.
Cc: <stable@vger.kernel.org> # 3.12.x : 39434ab n_tty: Fix missing newline echo
Reported-by: Karl Dahlke <eklhad@comcast.net>
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-by: Karl Dahlke <eklhad@comcast.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Newer Intel PCHs with LPSS have the same Designware controllers than
Haswell but ACPI IDs are different. Add these IDs to the driver list.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mark the function hvc_poll_init() as static in hvc/hvc_console.c because
it is not used outside this file.
This eliminates the following warning in hvc/hvc_console.c:
drivers/tty/hvc/hvc_console.c:791:5: warning: no previous prototype for ‘hvc_poll_init’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Marks the functions gsm_cleanup_mux(), gsm_activate_mux(),
gsm_free_mux(), gsm_alloc_mux() and gsm_change_mtu() as static in
n_gsm.c because they are not used outside this file.
Also, drop the EXPORT_SYMBOL_GPL for the above mentioned functions
because nothing else in the kernel calls them.
This eliminates the following warnings in n_gsm.c:
drivers/tty/n_gsm.c:2022:6: warning: no previous prototype for ‘gsm_cleanup_mux’ [-Wmissing-prototypes]
drivers/tty/n_gsm.c:2076:5: warning: no previous prototype for ‘gsm_activate_mux’ [-Wmissing-prototypes]
drivers/tty/n_gsm.c:2120:6: warning: no previous prototype for ‘gsm_free_mux’ [-Wmissing-prototypes]
drivers/tty/n_gsm.c:2156:17: warning: no previous prototype for ‘gsm_alloc_mux’ [-Wmissing-prototypes]
drivers/tty/n_gsm.c:2714:5: warning: no previous prototype for ‘gsm_change_mtu’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When falling back from DMA to interrupt mode the receive interrupt has to
be re-enabled to catch new incoming data.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In pl011_rx_chars() if pl011_dma_rx_trigger_dma() succeeds it will disable
the receive interrupt, no need to do this again.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During initialisation, a UART may already be in use for a console, so
take care to preserve things like baud rate and data format to avoid
corrupting console output.
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code to cope with a split tx/rx LCR_H register is non-trivial
so put it into it's own function to avoid duplication.
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the pl011 is being used for a console, pl011_console_write forces
the control register (CR) to enable the UART for transmission and then
restores this to the original value afterwards. It does this while
holding the port lock.
Unfortunately, when the uart is started or shutdown - say in response to
userland using the serial device for a terminal - then this updates the
control register without any locking.
This means we can have
pl011_console_write Save CR
pl011_startup Initialise CR, e.g. enable receive
pl011_console_write Restore old CR with receive not enabled
this result is a serial port which doesn't respond to any input.
A similar race in reverse could happen when the device is shutdown.
We can fix these problems by taking the port lock when updating CR.
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 17438217a6 on request
of Linus Walleij:
Greg can you please drop or revert
commit 17438217a6
"serial: pl011: use DMA RX polling by default"
from the TTY tree until this has been sorted out?
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
readline() inadvertently triggers an error recovery path when
pastes larger than 4k overrun the line discipline buffer. The
error recovery path discards input when the line discipline buffer
is full and operating in canonical mode and no newline has been
received. Because readline() changes the termios to non-canonical
mode to read the line char-by-char, the line discipline buffer
can become full, and then when readline() restores termios back
to canonical mode for the caller, the now-full line discipline
buffer triggers the error recovery.
When changing termios from non-canon to canon mode and the read
buffer contains data, simulate an EOF push _without_ the
DISABLED_CHAR in the read buffer.
Importantly for the readline() problem, the termios can be
changed back to non-canonical mode without changes to the read
buffer occurring; ie., as if the previous termios change had not
happened (as long as no intervening read took place).
Preserve existing userspace behavior which allows '\0's already
received in non-canon mode to be read as '\0's in canon mode
(rather than trigger add'l EOF pushes or an actual EOF).
Patch based on original proposal and discussion here
https://bugzilla.kernel.org/show_bug.cgi?id=55991
by Stas Sergeev <stsp@users.sourceforge.net>
Reported-by: Margarita Manterola <margamanterola@gmail.com>
Cc: Maximiliano Curia <maxy@gnuservers.com.ar>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Arkadiusz Miskiewicz <a.miskiewicz@gmail.com>
Acked-by: Stas Sergeev <stsp@users.sourceforge.net>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a complex patch for refactoring CLPS711X serial driver.
Major changes:
- Eliminate <mach/hardware.h> usage.
- Devicetree support.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit c49436b657 (serial: 8250_dw: Improve unwritable LCR workaround)
caused a regression. It added a check that the LCR was written properly
to detect and workaround the busy quirk, but the behaviour of bit 5
(UART_LCR_SPAR) differs between IP versions 3.00a and 3.14c per the
docs. On older versions this caused the check to fail and it would
repeatedly force idle and rewrite the LCR register, causing delays and
preventing any input from serial being received.
This is fixed by masking out UART_LCR_SPAR before making the comparison.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Tim Kryger <tim.kryger@linaro.org>
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Cc: Matt Porter <matt.porter@linaro.org>
Cc: Markus Mayer <markus.mayer@linaro.org>
Tested-by: Tim Kryger <tim.kryger@linaro.org>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a controlling tty is being hung up and the hang up is
waiting for a just-signalled tty reader or writer to exit, and a new tty
reader/writer tries to acquire an ldisc reference concurrently with the
ldisc reference release from the signalled reader/writer, the hangup
can hang. The new reader/writer is sleeping in ldsem_down_read() and the
hangup is sleeping in ldsem_down_write() [1].
The new reader/writer fails to wakeup the waiting hangup because the
wrong lock count value is checked (the old lock count rather than the new
lock count) to see if the lock is unowned.
Change helper function to return the new lock count if the cmpxchg was
successful; document this behavior.
[1] edited dmesg log from reporter
SysRq : Show Blocked State
task PC stack pid father
systemd D ffff88040c4f0000 0 1 0 0x00000000
ffff88040c49fbe0 0000000000000046 ffff88040c4a0000 ffff88040c49ffd8
00000000001d3980 00000000001d3980 ffff88040c4a0000 ffff88040593d840
ffff88040c49fb40 ffffffff810a4cc0 0000000000000006 0000000000000023
Call Trace:
[<ffffffff810a4cc0>] ? sched_clock_cpu+0x9f/0xe4
[<ffffffff810a4cc0>] ? sched_clock_cpu+0x9f/0xe4
[<ffffffff810a4cc0>] ? sched_clock_cpu+0x9f/0xe4
[<ffffffff810a4cc0>] ? sched_clock_cpu+0x9f/0xe4
[<ffffffff817a6649>] schedule+0x24/0x5e
[<ffffffff817a588b>] schedule_timeout+0x15b/0x1ec
[<ffffffff810a4cc0>] ? sched_clock_cpu+0x9f/0xe4
[<ffffffff817aa691>] ? _raw_spin_unlock_irq+0x24/0x26
[<ffffffff817aa10c>] down_read_failed+0xe3/0x1b9
[<ffffffff817aa26d>] ldsem_down_read+0x8b/0xa5
[<ffffffff8142b5ca>] ? tty_ldisc_ref_wait+0x1b/0x44
[<ffffffff8142b5ca>] tty_ldisc_ref_wait+0x1b/0x44
[<ffffffff81423f5b>] tty_write+0x7d/0x28a
[<ffffffff814241f5>] redirected_tty_write+0x8d/0x98
[<ffffffff81424168>] ? tty_write+0x28a/0x28a
[<ffffffff8115d03f>] do_loop_readv_writev+0x56/0x79
[<ffffffff8115e604>] do_readv_writev+0x1b0/0x1ff
[<ffffffff8116ea0b>] ? do_vfs_ioctl+0x32a/0x489
[<ffffffff81167d9d>] ? final_putname+0x1d/0x3a
[<ffffffff8115e6c7>] vfs_writev+0x2e/0x49
[<ffffffff8115e7d3>] SyS_writev+0x47/0xaa
[<ffffffff817ab822>] system_call_fastpath+0x16/0x1b
bash D ffffffff81c104c0 0 5469 5302 0x00000082
ffff8800cf817ac0 0000000000000046 ffff8804086b22a0 ffff8800cf817fd8
00000000001d3980 00000000001d3980 ffff8804086b22a0 ffff8800cf817a48
000000000000b9a0 ffff8800cf817a78 ffffffff81004675 ffff8800cf817a44
Call Trace:
[<ffffffff81004675>] ? dump_trace+0x165/0x29c
[<ffffffff810a4cc0>] ? sched_clock_cpu+0x9f/0xe4
[<ffffffff8100edda>] ? save_stack_trace+0x26/0x41
[<ffffffff817a6649>] schedule+0x24/0x5e
[<ffffffff817a588b>] schedule_timeout+0x15b/0x1ec
[<ffffffff810a4cc0>] ? sched_clock_cpu+0x9f/0xe4
[<ffffffff817a9f03>] ? down_write_failed+0xa3/0x1c9
[<ffffffff817aa691>] ? _raw_spin_unlock_irq+0x24/0x26
[<ffffffff817a9f0b>] down_write_failed+0xab/0x1c9
[<ffffffff817aa300>] ldsem_down_write+0x79/0xb1
[<ffffffff817aada3>] ? tty_ldisc_lock_pair_timeout+0xa5/0xd9
[<ffffffff817aada3>] tty_ldisc_lock_pair_timeout+0xa5/0xd9
[<ffffffff8142bf33>] tty_ldisc_hangup+0xc4/0x218
[<ffffffff81423ab3>] __tty_hangup+0x2e2/0x3ed
[<ffffffff81424a76>] disassociate_ctty+0x63/0x226
[<ffffffff81078aa7>] do_exit+0x79f/0xa11
[<ffffffff81086bdb>] ? get_signal_to_deliver+0x206/0x62f
[<ffffffff810b4bfb>] ? lock_release_holdtime.part.8+0xf/0x16e
[<ffffffff81079b05>] do_group_exit+0x47/0xb5
[<ffffffff81086c16>] get_signal_to_deliver+0x241/0x62f
[<ffffffff810020a7>] do_signal+0x43/0x59d
[<ffffffff810f2af7>] ? __audit_syscall_exit+0x21a/0x2a8
[<ffffffff810b4bfb>] ? lock_release_holdtime.part.8+0xf/0x16e
[<ffffffff81002655>] do_notify_resume+0x54/0x6c
[<ffffffff817abaf8>] int_signal+0x12/0x17
Reported-by: Sami Farin <sami.farin@gmail.com>
Cc: <stable@vger.kernel.org> # 3.12.x
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Turn clk_enable() and clk_disable() calls into clk_prepare_enable() and
clk_disable_unprepare() to get ready for the migration to the common
clock framework.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The break timer accesses hardware registers and thus requires the port
to be enabled. It currently ensures this by enabling the port at the
beginning of the timer handler, and disabling it at the end. However,
the enable/disable operations call the runtime PM sync functions, which
are not allowed in atomic context. The current situation is thus broken.
This change relies on non-atomic code to enable/disable the port. The
break timer will only be started from the IRQ handler, which already
runs with the port enabled. We just need to ensure that the port won't
be disabled with the timer running, and that's easily done by just
cancelling the timer in the port disable function.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Use the %zu and %pad printk specifiers to print size_t and dma_addr_t
variables, and cast pointers to uintptr_t instead of unsigned int where
applicable. This fixes warnings on platforms where pointers and/or
dma_addr_t have a different size than int.
Cc: linux-serial@vger.kernel.org
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
By using dma_request_slave_channel_or_err(), the DMA slave ID can be
looked up from standard DT properties, and squirrelled away during
channel allocation. Hence, there's no need to use a custom DT property
to store the slave ID.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tegra's clock driver now provides an implementation of the common
reset API (include/linux/reset.h). Use this instead of the old Tegra-
specific API; that will soon be removed.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Thierry Reding <treding@nvidia.com>
tty flip buffers use GFP_ATOMIC allocations for received data
which is to be processed by the line discipline. For each byte
received, an extra byte is used to indicate the error status of
that byte.
Instead, if the received data is error-free, encode the entire
buffer without status bytes.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 'tty: xuartps: Implement BREAK detection, add SYSRQ support'
(0c0c47bc40) introduced sysrq support
without properly guarding sysrq specific code which results in build
errors when sysrq is disabled:
DNAME=KBUILD_STR(xilinx_uartps)" -c -o
drivers/tty/serial/.tmp_xilinx_uartps.o
drivers/tty/serial/xilinx_uartps.c
drivers/tty/serial/xilinx_uartps.c: In function 'xuartps_isr':
drivers/tty/serial/xilinx_uartps.c:247:5: error: 'struct uart_port'
has no member named 'sysrq'
drivers/tty/serial/xilinx_uartps.c:247:5: error: 'struct uart_port'
has no member named 'sysrq'
drivers/tty/serial/xilinx_uartps.c:247:5: error: 'struct uart_port'
has no member named 'sysrq'
make[3]: *** [drivers/tty/serial/xilinx_uartps.o] Error 1
Reported-by: Masanari Iida <standby24x7@gmail.com>
Cc: Vlad Lungu <vlad.lungu@windriver.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the initialisation of older Quatech serial cards which are fitted with
the AMCC PCI Matchmaker interface chip.
Signed-off-by: Jonathan Woithe (jwoithe@just42.net)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We use "fw" in the next line after we release it. I've shifted the call
to release_firmware() down a couple lines to fix this.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Newer Intel PCHs with LPSS have the same Designware controllers than
Haswell but ACPI IDs are different. Add these IDs to the driver list.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
if the DMA driver isn't loaded "on time" then we crash in the irq handler:
| pch_uart 0000:02:0a.4: pch_request_dma:dma_request_channel FAILS(Tx)
| BUG: unable to handle kernel NULL pointer dereference at (null)
| IP: [<c0676ed9>] pch_uart_interrupt+0x739/0x940
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 60e9357547 (serial: samsung: enable clock before clearing pending
interrupts during init) added handling of the controller clock during init.
On most systems this clock is also one of the baud_clock sources and
possibly used by the earlycon and thus already enabled by the bootloader.
Therefore a gap exists between s3c24xx_serial_init_port disabling the
clock and an attached console reenabling it, making the transition from
earlycon to regular console possibly hang the system - as seen on my
S3C2442 based Freerunner today.
Therefore move the disabling of the clock from s3c24xx_serial_init_port
below the uart port registration, effectively creating an overlap and
keeping the clock running non-stop if the console wants to grab this port.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
clk_prepare_enable() may fail, so let's check its return value and propagate it
in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit d7a68be4f2,
'tty: Only perform flip buffer flush from tty_buffer_flush()',
removed buffer flushing from flush_to_ldisc().
Fix function header comment which describes the former behavior.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert to modern PM ops and use the SIMPLE_DEV_PM_OPS macro to set up
the PM callbacks.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't use DEFINE_PCI_DEVICE_TABLE macro, because this macro
is not preferred.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Making DMA RX polling optional when DMA is on was just
over-cautious: there is one single system in the kernel tree
using this facility, Ux500 and after some testing I turned
this on also for Ux500, which means it should simply be on
by default if DMA is enabled.
Cc: Jongsung Kim <neidhard.kim@lge.com>
Cc: Chanho Min <chanho.min@lge.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert to modern PM ops and use the SIMPLE_DEV_PM_OPS macro to set up
the PM callbacks.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ttyA has ld associated to n_gsm, when ttyA is closing, it triggers
to release gsmttyB's ld data dlci[B], then race would happen if gsmttyB
is opening in parallel.
(Note: This patch set differs from previous set in that it uses mutex
instead of spin lock to avoid race, so that it avoids sleeping in automic
context)
Here are race cases we found recently in test:
CASE #1
====================================================================
releasing dlci[B] race with gsmtty_install(gsmttyB), then panic
in gsmtty_open(gsmttyB), as below:
tty_release(ttyA) tty_open(gsmttyB)
| |
----- gsmtty_install(gsmttyB)
| |
----- gsm_dlci_alloc(gsmttyB) => alloc dlci[B]
tty_ldisc_release(ttyA) -----
| |
gsm_dlci_release(dlci[B]) -----
| |
gsm_dlci_free(dlci[B]) -----
| |
----- gsmtty_open(gsmttyB)
gsmtty_open()
{
struct gsm_dlci *dlci = tty->driver_data; => here it uses dlci[B]
...
}
In gsmtty_open(gsmttyA), it uses dlci[B] which was release, so hit a panic.
=====================================================================
CASE #2
=====================================================================
releasing dlci[0] race with gsmtty_install(gsmttyB), then panic
in gsmtty_open(), as below:
tty_release(ttyA) tty_open(gsmttyB)
| |
----- gsmtty_install(gsmttyB)
| |
----- gsm_dlci_alloc(gsmttyB) => alloc dlci[B]
| |
----- gsmtty_open(gsmttyB) fail
| |
----- tty_release(gsmttyB)
| |
----- gsmtty_close(gsmttyB)
| |
----- gsmtty_detach_dlci(dlci[B])
| |
----- dlci_put(dlci[B])
| |
tty_ldisc_release(ttyA) -----
| |
gsm_dlci_release(dlci[0]) -----
| |
gsm_dlci_free(dlci[0]) -----
| |
----- dlci_put(dlci[0])
In gsmtty_detach_dlci(dlci[B]), it tries to use dlci[0] which was released,
then hit panic.
=====================================================================
IMHO, n_gsm tty operations would refer released ldisc, as long as
gsm_dlci_release() has chance to release ldisc data when some gsmtty operations
are ongoing..
This patch is try to avoid it by:
1) in n_gsm driver, use a global gsm mutex lock to avoid gsm_dlci_release() run in
parallel with gsmtty_install();
2) Increase dlci's ref count in gsmtty_install() instead of in gsmtty_open(), the
purpose is to prevent gsm_dlci_release() releasing dlci after gsmtty_install()
allocats dlci but before gsmtty_open increases dlci's ref count;
3) Decrease dlci's ref count in gsmtty_remove(), a tty framework API, this is the
opposite process of step 2).
Signed-off-by: Chao Bi <chao.bi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no in-tree user of tty_prepare_flip_string_flags(); remove.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trim up the memory_used field name to mem_used.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allow driver to configure its maximum flip buffer memory
consumption/limit. This is necessary for very-high speed line
rates (in excess of 10MB/sec) because the flip buffers can
be saturated before the line discipline has a chance to
throttle the input.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Most line disciplines already handle the undocumented NULL flag
ptr in their .receive_buf method; however, several don't.
Document the NULL flag ptr, and correct handling in the
N_MOUSE, N_GSM0710 and N_R394 line disciplines.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Distinguish if caller is n_tty_poll() or n_tty_read(), and
set the read/wakeup threshold accordingly.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Although n_tty_receive_char_closing() only has one call-site,
let the compiler inline instead.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e60d27c4d8,
n_tty: Factor LNEXT processing from per-char i/o path,
mistakenly inlined the non-inline alias, n_tty_receive_char(),
for the inline function, n_tty_receive_char_inline().
As n_tty_receive_char() is intended for slow-path char
processing only, un-inline it.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
N_TTY's direct and flow-controlled flavors of the .receive_buf()
method are nearly identical; fold together.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This early amba_ports declaration was introduced by commit c16d51a32 (amba
pl011: workaround for uart registers lockup) for use in the pl011_lockup_wa()
routine. This routine was later removed by commit 4fd0690bb (serial: pl011:
implement workaround for CTS clear event issue).
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ACPI now provides stubs for the functions the driver uses.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The uart_set_options() code unconditionally initalizes the spinlock
on the port. This can cause a deadlock in some situations.
One instance that exposed the problem, was when writing to
/sys/module/kgdboc/parameters/kgdboc to use ttyS0 when the console
is already running on ttyS0. If the spinlock is re-initialized
while the lock is held due to output to the console, there
is a deadlock.
Assume the spinlock is initialized if the port is a console.
Signed-off-by: Randy Witt <rewitt@declaratino.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When L_ECHONL is on, newlines are echoed regardless of the L_ECHO
state; if set, ensure accumulated echoes are flushed before finishing
the current input processing and before more output.
Cc: <stable@vger.kernel.org> # 3.12.x
Reported-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit c284ee2cf1. Turns out
the locking was incorrect.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: Chao Bi <chao.bi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With multiple, concurrent readers (each waiting to acquire the
atomic_read_lock mutex), a departing reader may mistakenly reset
minimum_to_wake after a new reader has already set a new value.
Protect the minimum_to_wake reset with the atomic_read_lock critical
section.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A common security idiom is to hangup the current tty (via vhangup())
after forking but before execing a root shell. This hangs up any
existing opens which other processes may have and ensures subsequent
opens have the necessary permissions to open the root shell tty/pty.
Reset the TTY_HUPPED state after the driver has successfully
returned the opened tty (perform the reset while the tty is locked
to avoid racing with concurrent hangups).
Reported-by: Heorhi Valakhanovich <valahanovich@tut.by>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Cc: stable <stable@vger.kernel.org> # 3.12
Tested-by: Heorhi Valakhanovich <valahanovich@tut.by>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When booting a multi-platform m68k kernel on a non-Amiga with
"console=ttyS0" on the kernel command line, it crashes with:
Unable to handle kernel access at virtual address 81dff01c
Oops: 00000000
PC: [<001e09a8>] serial_console_write+0xc/0x70
Add the missing platform check to amiserial_console_init() to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When booting a multi-platform m68k kernel on a non-Mac with "console=ttyS0"
on the kernel command line, it crashes with:
Unable to handle kernel NULL pointer dereference at virtual address (null)
Oops: 00000000
PC: [<0013ad28>] __pmz_startup+0x32/0x2a0
...
Call Trace: [<002c5d3e>] pmz_console_setup+0x64/0xe4
The normal tty driver doesn't crash, because init_pmz() checks
pmz_ports_count again after calling pmz_probe().
In the serial console initialization path, pmz_console_init() doesn't do
this, causing the driver to crash later.
Add a check for pmz_ports_count to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ttyA has ld associated to n_gsm, when ttyA is closing, it triggers
to release gsmttyB's ld data dlci[B], then race would happen if gsmttyB
is opening in parallel.
Here are race cases we found recently in test:
CASE #1
====================================================================
releasing dlci[B] race with gsmtty_install(gsmttyB), then panic
in gsmtty_open(gsmttyB), as below:
tty_release(ttyA) tty_open(gsmttyB)
| |
----- gsmtty_install(gsmttyB)
| |
----- gsm_dlci_alloc(gsmttyB) => alloc dlci[B]
tty_ldisc_release(ttyA) -----
| |
gsm_dlci_release(dlci[B]) -----
| |
gsm_dlci_free(dlci[B]) -----
| |
----- gsmtty_open(gsmttyB)
gsmtty_open()
{
struct gsm_dlci *dlci = tty->driver_data; => here it uses dlci[B]
...
}
In gsmtty_open(gsmttyA), it uses dlci[B] which was release, so hit a panic.
=====================================================================
CASE #2
=====================================================================
releasing dlci[0] race with gsmtty_install(gsmttyB), then panic
in gsmtty_open(), as below:
tty_release(ttyA) tty_open(gsmttyB)
| |
----- gsmtty_install(gsmttyB)
| |
----- gsm_dlci_alloc(gsmttyB) => alloc dlci[B]
| |
----- gsmtty_open(gsmttyB) fail
| |
----- tty_release(gsmttyB)
| |
----- gsmtty_close(gsmttyB)
| |
----- gsmtty_detach_dlci(dlci[B])
| |
----- dlci_put(dlci[B])
| |
tty_ldisc_release(ttyA) -----
| |
gsm_dlci_release(dlci[0]) -----
| |
gsm_dlci_free(dlci[0]) -----
| |
----- dlci_put(dlci[0])
In gsmtty_detach_dlci(dlci[B]), it tries to use dlci[0] which was released,
then hit panic.
=====================================================================
IMHO, n_gsm tty operations would refer released ldisc, as long as
gsm_dlci_release() has chance to release ldisc data when some gsmtty operations
are not completed..
This patch is try to avoid it by:
1) in n_gsm driver, use a global gsm spin lock to avoid gsm_dlci_release() run in
parallel with gsmtty_install();
2) Increase dlci's ref count in gsmtty_install() instead of in gsmtty_open(), the
purpose is to prevent gsm_dlci_release() releasing dlci after gsmtty_install()
allocats dlci but before gsmtty_open increases dlci's ref count;
3) Decrease dlci's ref count in gsmtty_remove(), which is a tty framework api, and
this is the opposite process of step 2).
Signed-off-by: Chao Bi <chao.bi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 9326b047e4 includes a typo
of "8350_core" instead of "8250_core", so correct it.
Fixes kernel bugzilla #60724:
https://bugzilla.kernel.org/show_bug.cgi?id=60724
Reported-by: Christoph Biedl <bugzilla.kernel.bpeb@manchmal.in-ulm.de>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Although the maximum allowable canonical line is specified to
be 255 bytes (MAX_CANON), the practical limit has actually been
the size of the line discipline read buffer (N_TTY_BUF_SIZE == 4096).
Commit 32f13521ca,
n_tty: Line copy to user buffer in canonical mode, limited the
line copy to 4095 bytes. With a completely full line discipline
read buffer and a userspace buffer > 4095, _no_ data was copied,
and the read() syscall returned 0, indicating EOF.
Fix the interval arithmetic to compute the correct number of bytes
to copy to userspace in the range [1..4096].
Cc: <stable@vger.kernel.org> # 3.12.x
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit cbfd0340ae,
'n_tty: Process echoes in blocks', introduced an error when
consuming the echo buffer tail to prevent buffer overrun, where
the incorrect operation code byte is checked to determine how
far to advance the tail to the next echo byte.
Check the correct byte for the echo operation code byte.
Cc: <stable@vger.kernel.org> # 3.12.x : c476f65 tty: incorrect test of echo_buf() result for ECHO_OP_START
Cc: <stable@vger.kernel.org> # 3.12.x
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A departing reader must restart a flush_to_ldisc() worker _before_
the next reader enters the read loop; this is to avoid the new reader
concluding no more i/o is available and prematurely exiting, when the
old reader simply hasn't re-started the worker yet.
Cc: stable <stable@vger.kernel.org> # 3.12
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull slave-dmaengine changes from Vinod Koul:
"This brings for slave dmaengine:
- Change dma notification flag to DMA_COMPLETE from DMA_SUCCESS as
dmaengine can only transfer and not verify validaty of dma
transfers
- Bunch of fixes across drivers:
- cppi41 driver fixes from Daniel
- 8 channel freescale dma engine support and updated bindings from
Hongbo
- msx-dma fixes and cleanup by Markus
- DMAengine updates from Dan:
- Bartlomiej and Dan finalized a rework of the dma address unmap
implementation.
- In the course of testing 1/ a collection of enhancements to
dmatest fell out. Notably basic performance statistics, and
fixed / enhanced test control through new module parameters
'run', 'wait', 'noverify', and 'verbose'. Thanks to Andriy and
Linus [Walleij] for their review.
- Testing the raid related corner cases of 1/ triggered bugs in
the recently added 16-source operation support in the ioatdma
driver.
- Some minor fixes / cleanups to mv_xor and ioatdma"
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (99 commits)
dma: mv_xor: Fix mis-usage of mmio 'base' and 'high_base' registers
dma: mv_xor: Remove unneeded NULL address check
ioat: fix ioat3_irq_reinit
ioat: kill msix_single_vector support
raid6test: add new corner case for ioatdma driver
ioatdma: clean up sed pool kmem_cache
ioatdma: fix selection of 16 vs 8 source path
ioatdma: fix sed pool selection
ioatdma: Fix bug in selftest after removal of DMA_MEMSET.
dmatest: verbose mode
dmatest: convert to dmaengine_unmap_data
dmatest: add a 'wait' parameter
dmatest: add basic performance metrics
dmatest: add support for skipping verification and random data setup
dmatest: use pseudo random numbers
dmatest: support xor-only, or pq-only channels in tests
dmatest: restore ability to start test at module load and init
dmatest: cleanup redundant "dmatest: " prefixes
dmatest: replace stored results mechanism, with uniform messages
Revert "dmatest: append verify result to results"
...
- SWIOTLB has tracing added when doing bounce buffer.
- Xen ARM/ARM64 can use Xen-SWIOTLB. This work allows Linux to
safely program real devices for DMA operations when running as
a guest on Xen on ARM, without IOMMU support.*1
- xen_raw_printk works with PVHVM guests if needed.
Bug-fixes:
- Make memory ballooning work under HVM with large MMIO region.
- Inform hypervisor of MCFG regions found in ACPI DSDT.
- Remove deprecated IRQF_DISABLED.
- Remove deprecated __cpuinit.
[*1]:
"On arm and arm64 all Xen guests, including dom0, run with second stage
translation enabled. As a consequence when dom0 programs a device for a
DMA operation is going to use (pseudo) physical addresses instead
machine addresses. This work introduces two trees to track physical to
machine and machine to physical mappings of foreign pages. Local pages
are assumed mapped 1:1 (physical address == machine address). It
enables the SWIOTLB-Xen driver on ARM and ARM64, so that Linux can
translate physical addresses to machine addresses for dma operations
when necessary. " (Stefano).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQEcBAABAgAGBQJSgS86AAoJEFjIrFwIi8fJpY4H/R2gke1A1p9UvTwbkaDhgPs/
u/mkI6aH+ktgvu5QZNprki660uydtc4Ck7y8leeLGYw+ed1Ys559SJhRc/x8jBYZ
Hh2chnplld0LAjSpdIDTTePArE1xBo4Gz+fT0zc5cVh0leJwOXn92Kx8N5AWD/T3
gwH4Ok4K1dzZBIls7imM2AM/L1xcApcx3Dl/QpNcoePQtR4yLuPWMUbb3LM8pbUY
0B6ZVN4GOhtJ84z8HRKnh4uMnBYmhmky6laTlHVa6L+j1fv7aAPCdNbePjIt/Pvj
HVYB1O/ht73yHw0zGfK6lhoGG8zlu+Q7sgiut9UsGZZfh34+BRKzNTypqJ3ezQo=
=xc43
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.13-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen updates from Konrad Rzeszutek Wilk:
"This has tons of fixes and two major features which are concentrated
around the Xen SWIOTLB library.
The short <blurb> is that the tracing facility (just one function) has
been added to SWIOTLB to make it easier to track I/O progress.
Additionally under Xen and ARM (32 & 64) the Xen-SWIOTLB driver
"is used to translate physical to machine and machine to physical
addresses of foreign[guest] pages for DMA operations" (Stefano) when
booting under hardware without proper IOMMU.
There are also bug-fixes, cleanups, compile warning fixes, etc.
The commit times for some of the commits is a bit fresh - that is b/c
we wanted to make sure we have the Ack's from the ARM folks - which
with the string of back-to-back conferences took a bit of time. Rest
assured - the code has been stewing in #linux-next for some time.
Features:
- SWIOTLB has tracing added when doing bounce buffer.
- Xen ARM/ARM64 can use Xen-SWIOTLB. This work allows Linux to
safely program real devices for DMA operations when running as a
guest on Xen on ARM, without IOMMU support. [*1]
- xen_raw_printk works with PVHVM guests if needed.
Bug-fixes:
- Make memory ballooning work under HVM with large MMIO region.
- Inform hypervisor of MCFG regions found in ACPI DSDT.
- Remove deprecated IRQF_DISABLED.
- Remove deprecated __cpuinit.
[*1]:
"On arm and arm64 all Xen guests, including dom0, run with second
stage translation enabled. As a consequence when dom0 programs a
device for a DMA operation is going to use (pseudo) physical
addresses instead machine addresses. This work introduces two trees
to track physical to machine and machine to physical mappings of
foreign pages. Local pages are assumed mapped 1:1 (physical address
== machine address). It enables the SWIOTLB-Xen driver on ARM and
ARM64, so that Linux can translate physical addresses to machine
addresses for dma operations when necessary. " (Stefano)"
* tag 'stable/for-linus-3.13-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: (32 commits)
xen/arm: pfn_to_mfn and mfn_to_pfn return the argument if nothing is in the p2m
arm,arm64/include/asm/io.h: define struct bio_vec
swiotlb-xen: missing include dma-direction.h
pci-swiotlb-xen: call pci_request_acs only ifdef CONFIG_PCI
arm: make SWIOTLB available
xen: delete new instances of added __cpuinit
xen/balloon: Set balloon's initial state to number of existing RAM pages
xen/mcfg: Call PHYSDEVOP_pci_mmcfg_reserved for MCFG areas.
xen: remove deprecated IRQF_DISABLED
x86/xen: remove deprecated IRQF_DISABLED
swiotlb-xen: fix error code returned by xen_swiotlb_map_sg_attrs
swiotlb-xen: static inline xen_phys_to_bus, xen_bus_to_phys, xen_virt_to_bus and range_straddles_page_boundary
grant-table: call set_phys_to_machine after mapping grant refs
arm,arm64: do not always merge biovec if we are running on Xen
swiotlb: print a warning when the swiotlb is full
swiotlb-xen: use xen_dma_map/unmap_page, xen_dma_sync_single_for_cpu/device
xen: introduce xen_dma_map/unmap_page and xen_dma_sync_single_for_cpu/device
tracing/events: Fix swiotlb tracepoint creation
swiotlb-xen: use xen_alloc/free_coherent_pages
xen: introduce xen_alloc/free_coherent_pages
...
Use this new function to make code more comprehensible, since we are
reinitialzing the completion, not initializing.
[akpm@linux-foundation.org: linux-next resyncs]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for deferred
probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJSgPQ4AAoJEMhvYp4jgsXif28H/1WkrXq5+lCFQZF8nbYdE2h0
R8PsfiJJmAl6/wFgQTsRel+ScMk2hiP08uTyqf2RLnB1v87gCF7MKVaLOdONfUDi
huXbcQGWCmZv0tbBIklxJe3+X3FIJch4gnyUvPudD1m8a0R0LxWXH/NhdTSFyB20
PNjhN/IzoN40X1PSAhfB5ndWnoxXBoehV/IVHVDU42vkPVbVTyGAw5qJzHW8CLyN
2oGTOalOO4ffQ7dIkBEQfj0mrgGcODToPdDvUQyyGZjYK2FY2sGrjyquir6SDcNa
Q4gwatHTu0ygXpyphjtQf5tc3ZCejJ/F0s3olOAS1ahKGfe01fehtwPRROQnCK8=
=GCbY
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
"DeviceTree updates for 3.13. This is a bit larger pull request than
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for
deferred probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates"
* tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (82 commits)
powerpc: add missing explicit OF includes for ppc
dt/irq: add empty of_irq_count for !OF_IRQ
dt: disable self-tests for !OF_IRQ
of: irq: Fix interrupt-map entry matching
MIPS: Netlogic: replace early_init_devtree() call
of: Add Panasonic Corporation vendor prefix
of: Add Chunghwa Picture Tubes Ltd. vendor prefix
of: Add AU Optronics Corporation vendor prefix
of/irq: Fix potential buffer overflow
of/irq: Fix bug in interrupt parsing refactor.
of: set dma_mask to point to coherent_dma_mask
of: add vendor prefix for PHYTEC Messtechnik GmbH
DT: sort vendor-prefixes.txt
of: Add vendor prefix for Cadence
of: Add empty for_each_available_child_of_node() macro definition
arm/versatile: Fix versatile irq specifications.
of/irq: create interrupts-extended property
microblaze/pci: Drop PowerPC-ism from irq parsing
of/irq: Create of_irq_parse_and_map_pci() to consolidate arch code.
of/irq: Use irq_of_parse_and_map()
...
Pull powerpc updates from Benjamin Herrenschmidt:
"The bulk of this is LE updates. One should now be able to build an LE
kernel and even run some things in it.
I'm still sitting on a handful of patches to enable the new ABI that I
*might* still send this merge window around, but due to the
incertainty (they are pretty fresh) I want to keep them separate.
Other notable changes are some infrastructure bits to better handle
PCI pass-through under KVM, some bits and pieces added to the new
PowerNV platform support such as access to the CPU SCOM bus via sysfs,
and support for EEH error handling on PHB3 (Power8 PCIe).
We also grew arch_get_random_long() for both pseries and powernv when
running on P7+ and P8, exploiting the HW rng.
And finally various embedded updates from freescale"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (154 commits)
powerpc: Fix fatal SLB miss when restoring PPR
powerpc/powernv: Reserve the correct PE number
powerpc/powernv: Add PE to its own PELTV
powerpc/powernv: Add support for indirect XSCOM via debugfs
powerpc/scom: Improve debugfs interface
powerpc/scom: Enable 64-bit addresses
powerpc/boot: Properly handle the base "of" boot wrapper
powerpc/bpf: Support MOD operation
powerpc/bpf: Fix DIVWU instruction opcode
of: Move definition of of_find_next_cache_node into common code.
powerpc: Remove big endianness assumption in of_find_next_cache_node
powerpc/tm: Remove interrupt disable in __switch_to()
powerpc: word-at-a-time optimization for 64-bit Little Endian
powerpc/bpf: BPF JIT compiler for 64-bit Little Endian
powerpc: Only save/restore SDR1 if in hypervisor mode
powerpc/pmu: Fix ADB_PMU_LED_IDE dependencies
powerpc/nvram: Fix endian issue when using the partition length
powerpc/nvram: Fix endian issue when reading the NVRAM size
powerpc/nvram: Scan partitions only once
powerpc/mpc512x: remove unnecessary #if
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQEcBAABAgAGBQJSWyGgAAoJEHm+PkMAQRiGA8MH/35upHXImoRCsI5uC1qvHJtI
QvQAhDFxoEXbFUKeaYgTfcM8q9FgnqnfjhLf8eYa4Q7tDZeqLXOE8bkI807mSZMl
yECr3jcwlV+zyhV2MP/HdwTjzy25bwxLM3Zy43S7QROrYoMHZYznil/QPfyMATCJ
XLPuXZC1FtuUen89n4BoDIuL8QaVrIR/zLqFklAQcdTcGpLHSOwFtH8gb2WaRLhv
+4IikFRFgTNZiMR5tP0GPc6UH6TVTvRb4QKSqqa7J8OmfAIvOzAUdhqWSPOIwWwt
Z/+JFxFDczAcNmpv4gE6jkgc2vR8CVeHsvh0j61RDSFObBWspwk337CSyUZxYSA=
=w4VQ
-----END PGP SIGNATURE-----
Merge tag 'v3.12-rc5' into stable/for-linus-3.13
Linux 3.12-rc5
Because the Stefano branch (for SWIOTLB ARM changes) is based on that.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
* tag 'v3.12-rc5': (550 commits)
Linux 3.12-rc5
watchdog: sunxi: Fix section mismatch
watchdog: kempld_wdt: Fix bit mask definition
watchdog: ts72xx_wdt: locking bug in ioctl
ARM: exynos: dts: Update 5250 arch timer node with clock frequency
parisc: let probe_kernel_read() capture access to page zero
parisc: optimize variable initialization in do_page_fault
parisc: fix interruption handler to respect pagefault_disable()
parisc: mark parisc_terminate() noreturn and cold.
parisc: remove unused syscall_ipi() function.
parisc: kill SMP single function call interrupt
parisc: Export flush_cache_page() (needed by lustre)
vfs: allow O_PATH file descriptors for fstatfs()
ext4: fix memory leak in xattr
ARC: Ignore ptrace SETREGSET request for synthetic register "stop_pc"
ALSA: hda - Sony VAIO Pro 13 (haswell) now has a working headset jack
ALSA: hda - Add a headset mic model for ALC269 and friends
ALSA: hda - Fix microphone for Sony VAIO Pro 13 (Haswell model)
compiler/gcc4: Add quirk for 'asm goto' miscompilation bug
Revert "i915: Update VGA arbiter support for newer devices"
...
Pull s390 updates from Martin Schwidefsky:
"The bulk of the patches for the 3.13 merge window.
Heiko spent quite a bit of work to improve the code generation for the
kernel. That includes the exploitation of the interlocked-access
facility for the atomics and bitops implementation and the improvement
for the -march and -mtune compiler settings.
Another important change is the removal of the user_mode=home option,
user processes now always run in primary space. The storage keys are
not initialized at system startup any more, with that the storage key
removal work is complete. For the PCI support the hibernation hooks
have been implemented.
And as usual cleanup and fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (62 commits)
s390/scm_blk: fix endless loop for requests != REQ_TYPE_FS
s390/mm,tlb: correct tlb flush on page table upgrade
s390/mm: page_table_realloc returns failure
s390: allow to set gcc -mtune flag
s390/percpu: remove this_cpu_xor() implementation
s390/vtime: correct idle time calculation
s390/time: fix get_tod_clock_ext inline assembly
tty/hvc_iucv: remove redundant NULL check
s390/dasd: Write to profile data area only if it is available
s390: convert use of typedef ctl_table to struct ctl_table
s390/pci: cleanup function information block
s390/pci: remove CONFIG_PCI_DEBUG dependancy
s390/pci: message cleanup
Update default configuration
s390: add a couple of useful defconfigs
s390/percpu: make use of interlocked-access facility 1 instructions
s390/percpu: use generic percpu ops for CONFIG_32BIT
s390/compat: make psw32_user_bits a constant value again
s390: fix handling of runtime instrumentation psw bit
s390: fix save and restore of the floating-point-control register
...
Here's the big tty/serial driver update for 3.13-rc1.
There's some more minor n_tty work here, but nothing like previous
kernel releases. Also some new driver ids, driver updates for new
hardware, and other small things.
All of this has been in linux-next for a while with no issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlJ6xnEACgkQMUfUDdst+ylj1QCfaIzUNuFfzTmyB6K6iZrRNhCc
WPgAnRLkkEpI/3rRo7jKwGQsuIuyybUu
=r149
-----END PGP SIGNATURE-----
Merge tag 'tty-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here's the big tty/serial driver update for 3.13-rc1.
There's some more minor n_tty work here, but nothing like previous
kernel releases. Also some new driver ids, driver updates for new
hardware, and other small things.
All of this has been in linux-next for a while with no issues"
* tag 'tty-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (84 commits)
serial: omap: fix missing comma
serial: sh-sci: Enable the driver on all ARM platforms
serial: mfd: Staticize local symbols
serial: omap: fix a few checkpatch warnings
serial: omap: improve RS-485 performance
mrst_max3110: fix unbalanced IRQ issue during resume
serial: omap: Add support for optional wake-up
serial: sirf: remove duplicate defines
tty: xuartps: Fix build error when COMMON_CLK is not set
tty: xuartps: Fix build error due to missing forward declaration
tty: xuartps: Fix "may be used uninitialized" build warning
serial: 8250_pci: add Pericom PCIe Serial board Support (12d8:7952/4/8) - Chip PI7C9X7952/4/8
tty: xuartps: Update copyright information
tty: xuartps: Implement suspend/resume callbacks
tty: xuartps: Dynamically adjust to input frequency changes
tty: xuartps: Updating set_baud_rate()
tty: xuartps: Force enable the UART in xuartps_console_write
tty: xuartps: support 64 byte FIFO size
tty: xuartps: Add polled mode support for xuartps
tty: xuartps: Implement BREAK detection, add SYSRQ support
...
Renesas ARM platforms are transitioning from single-platform to
multi-platform kernels using the new ARCH_SHMOBILE_MULTI. Make the
driver available on all ARM platforms to enable it on both ARCH_SHMOBILE
and ARCH_SHMOBILE_MULTI, and increase build testing coverage with
COMPILE_TEST.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These local symbols are used only in this file.
Fix the following sparse warnings:
drivers/tty/serial/mfd.c:296:6: warning: symbol 'hsu_dma_tx' was not declared. Should it be static?
drivers/tty/serial/mfd.c:343:6: warning: symbol 'hsu_dma_start_rx_chan' was not declared. Should it be static?
drivers/tty/serial/mfd.c:389:6: warning: symbol 'hsu_dma_rx' was not declared. Should it be static?
drivers/tty/serial/mfd.c:1186:17: warning: symbol 'serial_hsu_pops' was not declared. Should it be static?
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If RS-485 is enabled, make the OMAP UART fire THR interrupts when both
TX FIFO and TX shift register are empty instead of polling the
equivalent status bit. This removes the burst of interrupt requests
seen at every end of transmission.
Also: the comment said that the TX FIFO trigger level was set at 16
characters when it's 32 in reality.
Signed-off-by: Philippe Proulx <philippe.proulx@savoirfairelinux.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During resume, a startup will request_irq again, meantime resume function's
enable_irq will cause unbalanced IRQ issue.
Fix this issue by moving request_irq to probe function.
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Chen, Jie <jie.d.chen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the recent pinctrl-single changes, omaps can treat
wake-up events from deeper idle states as interrupts.
There's a separate "io chain" controller on most omaps
that stays enabled when the device hits off-idle and the
regular interrupt controller is powered off.
Let's add support for the optional second interrupt for
wake-up events. And then serial-omap can manage the
wake-up interrupt from it's runtime PM calls to avoid
spurious interrupts during runtime.
Note that the wake interrupt is board specific as it
uses the UART RX pin, and for omap3, there are six pin
options for UART3 RX pin.
Also Note that the legacy platform based booting handles
the wake-ups in the legacy mux driver and does not need to
pass the wake-up interrupt to the driver.
And finally, to pass the wake-up interrupt in the dts file,
either interrupt-map or the pending interrupts-extended
property needs to be passed. It's probably best to use
interrupts-extended when it's available.
Cc: Felipe Balbi <balbi@ti.com>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes duplicate defines in drivers/tty/serial/sirfsoc_uart.h
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clock notifiers are only available when CONFIG_COMMON_CLK is enabled.
Hence all notifier related code has to be protected by corresponsing
ifdefs.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If CONFIG_PM_SLEEP is enabled and CONFIG_SERIAL_XILINX_PS_UART_CONSOLE
is not, a forward declaration of the uart_driver struct is not
included, leading to a build error due to an undeclared variable.
Fixing this by moving the definition of the struct uart_driver before
the definition of the suspend/resume callbacks.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Initialize varibles for which a 'may be used uninitalized' warning is
issued.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make smatch happy and remove this warning:
drivers/tty/hvc/hvc_iucv.c:1320 hvc_iucv_init() info: redundant null check on
hvc_iucv_filter calling kfree()
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Replace some instances of of_irq_map_one()/irq_create_of_mapping() and
of_irq_to_resource() by the simpler equivalent irq_of_parse_and_map().
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
[grant.likely: resolved conflicts with core code renames]
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Implement suspend and resume callbacks in order to support system
suspend/hibernation.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a clock notifier to dynamically handle frequency changes of the
input clock by reprogramming the UART in order to keep the baud rate
constant.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The original algorithm to find the best baud rate dividers does not necessarily
find the best set of dividers. And in the worst case may even write illegal
values to the hardware.
The new function should make better use of the hardware capabilities and be able
to provide valid settings for a wider range of baud rates and also input clocks.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is possible that under certain circumstances xuartps_console_write is entered
while the UART disabled. When this happens the code will busy loop in
xuartps_console_putchar, since the character is never written and the TXEMPTY
flag is never set. The result is a system lockup. This patch force enables the
UART for the duration of xuartps_console_write to avoid this.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: John Linn <john.linn@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Changes to use the 64 byte FIFO depth and fix the issue
by clearing the txempty interrupt in isr status for tx
after filling in data in start_tx function
Signed-off-by: Suneel Garapati <suneelg@xilinx.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Cadence UART does not do break detection, even if the
datasheet says it does. This patch adds break detection in
software (tested in 8N1 mode only) and enables SYSRQ,
allowing for Break-g to enter KDB and all the other goodies.
Signed-off-by: Vlad Lungu <vlad.lungu@windriver.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On older SoC, the "name" field is not filled in the register map.
Fix the way to figure out if the serial port is an uart or an usart for these
older products (with corresponding properties).
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 055560b04a (serial: at91:
distinguish usart and uart) the older products which do not have a
name field in their register map are unable to use their serial output.
As the main console output is usually the serial interface (aka DBGU) it
is pretty unfortunate.
So, instead of failing during probe() we just silently configure the serial
peripheral as an uart. It allows us to use these serial outputs.
The proper solution is proposed in another patch.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 055560b04a (serial: at91:
distinguish usart and uart) the older products which do not have a
name field in their register map are unable to use their serial output.
As the main console output is usually the serial interface (aka DBGU) it
is pretty unfortunate.
So, instead of failing during probe() we just silently configure the serial
peripheral as an uart. It allows us to use these serial outputs.
The proper solution is proposed in another patch.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds support for Fintek's 4, 8, and 12 port PCIE serial cards.
Thanks to Fintek for the sample devices, and the spec needed in order to
implement this.
Cc: Amanda Ying <amanda_ying@fintek.com.tw>
Cc: Felix Shih <felix_shih@fintek.com.tw>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I worried that the delay of the sdma_run_channel0() maybe too long for
interrupt context, so I added the workqueues for RX/TX DMA.
But tested with bluetooth device, I find that the delay of sdma_run_channel0()
is about 8us (tested in imx6dl sabreauto board). I think the delay
is acceptable.
This patch removes the RX/TX workqueues for DMA, it makes the
code more clear.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to missing braces on an if statement, in presence of a device_node a
port was always assigned -1, regardless of any alias entries in the
device tree. Conversely, if device_node was NULL, an unitialized port
ended up being used.
This patch adds the missing braces, fixing the issues.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Tony Prisk <linux@prisktech.co.nz>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the dmaengine_tx_status to simplify the code, do not change any logic.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the (xmit->tail > xmit->head) is true and the xmit->head is 0,
we only need one DMA scatterlist in actually. Current code uses two DMA
scatterlists in this case, this is obviously wrong.
This patch fixes it.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Assume the following situation:
If the DMA is enabled, and the a TX DMA operation is working,
But we have not issued the TX DMA operation (or we have issued the
TX DMA operation with dma_async_issue_pending(), but the DMA has not
started to move the data from the memory to the TXFIFO).
At this time, we may get the wrong status of the transmitter when we
call the imx_tx_empty. In such situation, only check the USR2_TXDC
does not enough for us.
This patch checks the DMA's situation, and return 0 when the TX DMA is
working.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current driver does not implement the flush_buffer hook for
uart_ops. When we enable the DMA for the driver, and test it with Bluetooth,
we may meet the following bug for TX:
[1] User application may call the flush operation at any time.
The uart_flush_buffer() calls the uart_circ_clear() to set
the xmit->head and xmit->tail with 0.
[2] The TX DMA callback can be called at any time too.
The dma_tx_call() will update the xmit->tail.
If [2] occurs just after the [1], we will get the wrong xmit->tail.
This patch implements the flush_buffer hook to fix this issue.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This callback is gone and not coming back, so will not be
supported later.
Cc: Johan Hovold <jhovold@gmail.com>
Acked-by: Darren Hart <dvhart@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This callback is gone and not coming back, so will not be
supported later.
Cc: Gerhard Sittig <gsi@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This callback is unused by the serial core since pre-git days
and is not coming back. Delete it. Enabling wakeup on the
SA1100 platforms should be done in the suspend() callback
so the platform hook is left in the serial port struct for
later enablement.
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This callback is unused by the serial core since pre-git days
and is not coming back. Delete it. Enabling wakeup on the
OMAP serial driver is done through other runpaths these days.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
test echo_buf() result for ECHO_OP_START
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These aren't necessary after switch and while blocks.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a race between termios configuration and xmit that can cause the
intel_mid_ssp_spi driver to stall.
Serializing spi transactions fixes the problem.
Signed-off-by: Bin Gao <bin.gao@intel.com>
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should check the validity of the irq number before calling
disable_irq() and enable_irq() in the suspend/resume function,
as "max->irq == 0" means the irq is not enabled for max3110
device, otherwise it will hurt device whose irq number is really 0.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add calls to clk_prepare and unprepare so that EMMA Mobile EV2 can
migrate to the common clock framework.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
[takashi.yoshii.ze@renesas.com: edited for conflicts]
Signed-off-by: Takashi Yoshii <takashi.yoshii.zj@renesas.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Turn the initial value of sysctl kernel.sysrq (SYSRQ_DEFAULT_ENABLE)
into a Kconfig variable.
Original version by Bastian Blank <waldi@debian.org>.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Powerpc is a mess of implicit includes by prom.h. Add the necessary
explicit includes to drivers in preparation of prom.h cleanup.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
This reverts commit f7d2c0bbdb, as it
causes build errors when the driver is built as a module.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When DMA is enabled (with hardware flow control enabled) the FIFO size
must be set to the size of the DMA buffer, as this is the size the tty
subsystem can use.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit d0380e6c3c (early_printk:
consolidate random copies of identical code) added in 3.10 introduced
a check for con->index == -1 in early_console_register().
Initialize index to -1 for the xenboot console so earlyprintk=xen
works again.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Driver core clears the driver data to NULL after device_release
or on probe failure, so just remove it from here.
Driver core change:
"device-core: Ensure drvdata = NULL when no driver is bound"
(sha1: 0998d06310)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When configured with UART_16550_COMPATIBLE=NO or in versions prior to
the introduction of this option, the Designware UART will ignore writes
to the LCR if the UART is busy. The current workaround saves a copy of
the last written LCR and re-writes it in the ISR for a special interrupt
that is raised when a write was ignored.
Unfortunately, interrupts are typically disabled prior to performing a
sequence of register writes that include the LCR so the point at which
the retry occurs is too late. An example is serial8250_do_set_termios()
where an ignored LCR write results in the baud divisor not being set and
instead a garbage character is sent out the transmitter.
Furthermore, since serial_port_out() offers no way to indicate failure,
a serious effort must be made to ensure that the LCR is actually updated
before returning back to the caller. This is difficult, however, as a
UART that was busy during the first attempt is likely to still be busy
when a subsequent attempt is made unless some extra action is taken.
This updated workaround reads back the LCR after each write to confirm
that the new value was accepted by the hardware. Should the hardware
ignore a write, the TX/RX FIFOs are cleared and the receive buffer read
before attempting to rewrite the LCR out of the hope that doing so will
force the UART into an idle state. While this may seem unnecessarily
aggressive, writes to the LCR are used to change the baud rate, parity,
stop bit, or data length so the data that may be lost is likely not
important. Admittedly, this is far from ideal but it seems to be the
best that can be done given the hardware limitations.
Lastly, the revised workaround doesn't touch the LCR in the ISR, so it
avoids the possibility of a "serial8250: too much work for irq" lock up.
This problem is rare in real situations but can be reproduced easily by
wiring up two UARTs and running the following commands.
# stty -F /dev/ttyS1 echo
# stty -F /dev/ttyS2 echo
# cat /dev/ttyS1 &
[1] 375
# echo asdf > /dev/ttyS1
asdf
[ 27.700000] serial8250: too much work for irq96
[ 27.700000] serial8250: too much work for irq96
[ 27.710000] serial8250: too much work for irq96
[ 27.710000] serial8250: too much work for irq96
[ 27.720000] serial8250: too much work for irq96
[ 27.720000] serial8250: too much work for irq96
[ 27.730000] serial8250: too much work for irq96
[ 27.730000] serial8250: too much work for irq96
[ 27.740000] serial8250: too much work for irq96
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Reviewed-by: Markus Mayer <markus.mayer@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the printk() calls to to dev_*() instead, to tie into the dynamic
debugging infrastructure.
Also change some "raw" printk() calls to dev_err() to provide a better
error message to userspace so it can properly identify the device and
not just have to guess.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__initdata tag should be placed between the variable name and equal
sign for the variable to be placed in the intended .init.data section.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit f95499c303,
n_tty: Don't wait for buffer work in read() loop
creates a race window which can cause a pty master read()
to miss the last pty slave write(s) and return -EIO instead,
thus signalling the pty slave is closed. This can happen when
the pty slave is written and immediately closed but before the
tty buffer i/o loop receives the new input; the pty master
read() is scheduled, sees its read buffer is empty and the
pty slave has been closed, and exits.
Because tty_flush_to_ldisc() has significant performance impact
for parallel i/o, rather than revert the commit, special case this
condition (ie., when the read buffer is empty and the 'other' pty
has been closed) and, only then, wait for buffer work to complete
before re-testing if the read buffer is still empty.
As before, subsequent pty master reads return any available data
until no more data is available, and then returns -EIO to
indicate the pty slave has closed.
Reported-by: Mikael Pettersson <mikpelinux@gmail.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-by: Mikael Pettersson <mikpelinux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xen_raw_printk works great for debugging purposes. We use
for PV guests and we can also use it for HVM guests.
However, for HVM guests we have a fallback of using the 0xe9
port in case the hypervisor does not support an HVM guest of
using the console_io hypercall. As such lets use 0xe9 during
early bootup, and once the hyper-page is setup and if the
console_io hypercall is supported - use that. Otherwise we
will fallback to using the 0xe9 after early bootup.
We also alter the return value for dom0_write_console to return
an error value instead of zero. The HVC API has been supporting
returning error values for quite some time.
P.S.
To use (and to see the output in the Xen ring buffer) one has to build
the hypervisor with 'debug=y'.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
[v1: ifdef xen_cpuid_base as it is X86 specific]
Here are some serial at tty driver fixes for 3.12-rc3
The serial driver fixes some kref leaks, documentation is moved to the proper
places, and the tty and n_tty fixes resolve some reported regressions. There
is still one outstanding tty regression fix that isn't in here yet, as I want
to test it out some more, it will be sent for 3.12-rc4 if it checks out.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.21 (GNU/Linux)
iEYEABECAAYFAlJIhfAACgkQMUfUDdst+yl+ywCdEKd9jfuZhU0RZ+j3wJIHXwBM
WFwAoIUPOI0CqKM1cLC/YIZwyn/pKjfY
=zkas
-----END PGP SIGNATURE-----
Merge tag 'tty-3.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some serial at tty driver fixes for 3.12-rc3
The serial driver fixes some kref leaks, documentation is moved to the
proper places, and the tty and n_tty fixes resolve some reported
regressions. There is still one outstanding tty regression fix that
isn't in here yet, as I want to test it out some more, it will be sent
for 3.12-rc4 if it checks out"
* tag 'tty-3.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: ar933x_uart: move devicetree binding documentation
tty: Fix SIGTTOU not sent with tcflush()
n_tty: Fix EOF push index when termios changes
serial: pch_uart: remove unnecessary tty_port_tty_get
serial: pch_uart: fix tty-kref leak in dma-rx path
serial: pch_uart: fix tty-kref leak in rx-error path
serial: tegra: fix tty-kref leak
The stub for dw8250_probe_acpi() is missing an argument.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel BayTrail has two HS-UARTs with 64 byte fifo, support
for DMA and support for 16750 compatible Auto Flow Control.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is not a bug on our side, but a misdesign in ITU T.416, yet with
all popular terminals supporting these codes, people consider this to
be a bug in Linux. By breaking the design principles behind SGR codes
(gracefully ignoring unsupported ones should not require knowing about
them), 256 colour ones tend to turn blinking on before invoking an
arbitrary unrelated command.
This commit doesn't add such support, merely skips such codes without
ill effects.
Signed-off-by: Adam Borowski <kilobyte@angband.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No modern terminal supports them, and SGR 38 conflicts with detecting
xterm-256 colours. This also makes SGR 39 consistent with other popular
terminals. Neither are used by ncurses' terminfo.
Signed-off-by: Adam Borowski <kilobyte@angband.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The original version of this was done by Bastian Blank, who wrote:
> The problem is the following:
> - Architecture specific code sets preferred console to something bogus.
> - Command line handling tries to set preferred console but is overruled
> by the old setting.
>
> The udbg0 console is a boot console and independant.
References: http://bugs.debian.org/492703
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The nice thing about devm_* is that the driver doesn't need to free the
resources but the driver core takes care about that.
These calls were introduced in commit c08f015 (serial: clps711x: Using
CPU clock subsystem for getting base UART speed).
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the missing uart_unregister_driver() before return
from sccnxp_probe() in the error handling case.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make Mode16 more preferred than Mode13, to match TRM baudrates table.
Signed-off-by: Alexey Pelykh <alexey.pelykh@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In rx timeout ISR and tasklet, we don't issue new dma desc as rx_done ISR
will do that.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This resolves a warning where resource_size_t is larger than void *:
drivers/tty/serial/imx.c:1542:6: warning: cast to pointer from integer
of different size [-Wint-to-pointer-cast]
Since iomem_base is a void *, casting to unsigned long is safe.
It's unclear to me that this comparison is truly needed, but it's there
on several other drivers as well.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Samsung serial driver currently does not support setting the
RTS pin with an ioctl(TIOCMSET) call. This patch adds this support.
Changes in v2:
- Preserve the RTS pin's manual setting in set_termios() also when
enabling CRTSCTS.
Signed-off-by: José Miguel Gonçalves <jose.goncalves@inov.pt>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Casting the return value which is a void pointer is redundant.
The conversion from void pointer to any other pointer type is
guaranteed by the C programming language.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Casting the return value which is a void pointer is redundant.
The conversion from void pointer to any other pointer type is
guaranteed by the C programming language.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Casting the return value which is a void pointer is redundant.
The conversion from void pointer to any other pointer type is
guaranteed by the C programming language.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Casting the return value which is a void pointer is redundant.
The conversion from void pointer to any other pointer type is
guaranteed by the C programming language.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Casting the return value which is a void pointer is redundant.
The conversion from void pointer to any other pointer type is
guaranteed by the C programming language.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Sonic Zhang <sonic.zhang@analog.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Casting the return value which is a void pointer is redundant.
The conversion from void pointer to any other pointer type is
guaranteed by the C programming language.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Casting the return value which is a void pointer is redundant.
The conversion from void pointer to any other pointer type is
guaranteed by the C programming language.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The channel IDs are set to -1 by default. It will prevent
dmaengine from trying to provide the first free channel if
it fails to allocate exclusive channel. This will fix an
issue with ACPI enumerated UARTs that do not support DMA
but still end up getting a DMA channel incorrectly.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It should be available for DT users as well. This does not
enable DMA by default except with ACPI. DT users can enable
DMA based on a property.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DMA engines usually expect the fifo trigger level to be
aligned with the burst size. It should not be changed even
with small baud rates. This will fix an issue with
Designware DMA engine where the data can not be transferred
over UART with lower baud rates then 2400.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pch_uart currently isn't auto-loaded if built as a module.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a PCI driver and should be auto-loaded based on PCI ID.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kconfig for this option suggests it's only relevant on STi SoCs,
so add depends to have it not show up on archs that won't ever run it.
Signed-off-by: Dave Jones <davej@fedoraproject.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit f7d2c0bbd (serial: i.MX: evaluate linux,stdout-path property) introduced
the following sparse warning:
drivers/tty/serial/imx.c:1916:77: warning: Using plain integer as NULL pointer
Pass NULL as the last argument of add_preferred_console() instead of zero.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enabling the ARM DCC console and using without a JTAG connection will
simply hang the system. Since distros like to turn on all options, this
is a reoccurring problem to debug. We can do better by checking if
anything is attached and handling characters. There is no way to probe
this, so send a newline and check that it is handled.
Cc: Paolo Pisati <paolo.pisati@canonical.com>
Cc: Tim Gardner <tim.gardner@canonical.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Although originally conceived as a hook for port drivers to know
when a port reference is dropped, no driver uses this method.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the tty driver mistakenly drops the last port reference
before the tty has been released, issue a diagnostic and
abort the port destruction.
This will leak memory and may zombify the port, but might
otherwise keep the machine in runnable state.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove braces from single-statement conditional in
n_tty_set_termios.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 'e7f3880cd9b98c5bf9391ae7acdec82b75403776'
tty: Fix recursive deadlock in tty_perform_flush()
introduced a regression where tcflush() does not generate
SIGTTOU for background process groups.
Make sure ioctl(TCFLSH) calls tty_check_change() when
invoked from the line discipline.
Cc: stable@vger.kernel.org # v3.10+
Reported-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Starting from v3.10 (probably commit f91e2590410b: "tty: Signal
foreground group processes in hangup") disassociate_ctty() sends SIGCONT
if tty && on_exit. This breaks LSB test-suite, in particular test8 in
_exit.c and test40 in sigcon5.c.
Put the "!on_exit" check back to restore the old behaviour.
Review by Peter Hurley:
"Yes, this regression was introduced by me in that commit. The effect
of the regression is that ptys will receive a SIGCONT when, in similar
circumstances, ttys would not.
The fact that two test vectors accidentally tripped over this
regression suggests that some other apps may as well.
Thanks for catching this"
Cc: stable@vger.kernel.org # v3.10+
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reported-by: Karel Srot <ksrot@redhat.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 40d5e0905a,
'n_tty: Fix EOF push handling' introduced a subtle state
change error wrt EOF push handling when the termios is
changed from non-canonical to canonical mode.
Reset line_start to the current read_tail index, not 0.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove unused tty-reference from dma-rx path which was left after the
recent tty-port conversions.
Also remove a redundant port initialisation while at it.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix tty_kref leak when tty_buffer_request room fails in dma-rx path.
Note that the tty ref isn't really needed anymore, but as the leak has
always been there, fixing it before removing should makes it easier to
backport the fix.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix tty-kref leak introduced by commit 384e301e ("pch_uart: fix a
deadlock when pch_uart as console") which never put its tty reference.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After the last architecture switched to generic hard irqs the config
options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
for !CONFIG_GENERIC_HARDIRQS can be removed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pull input updates from Dmitry Torokhov:
"A new driver for slidebar on Ideapad laptops and a bunch of assorted
driver fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (32 commits)
Input: add SYN_MAX and SYN_CNT constants
Input: max11801_ts - convert to devm
Input: egalax-ts - fix typo and improve text
Input: MAINTAINERS - change maintainer for cyttsp driver
Input: cyttsp4 - kill 'defined but not used' compiler warnings
Input: add driver for slidebar on Lenovo IdeaPad laptops
Input: omap-keypad - set up irq type from DT
Input: omap-keypad - enable wakeup capability for keypad.
Input: omap-keypad - clear interrupts on open
Input: omap-keypad - convert to threaded IRQ
Input: omap-keypad - use bitfiled instead of hardcoded values
Input: cyttsp4 - remove useless NULL test from cyttsp4_watchdog_timer()
Input: wacom - fix error return code in wacom_probe()
Input: as5011 - fix error return code in as5011_probe()
Input: keyboard, serio - simplify use of devm_ioremap_resource
Input: tegra-kbc - simplify use of devm_ioremap_resource
Input: htcpen - fix incorrect placement of __initdata
Input: qt1070 - add power management ops
Input: wistron_btns - add MODULE_DEVICE_TABLE
Input: wistron_btns - mark the Medion MD96500 keymap as tested
...
Device tree and bindings updates for 3.12.
General additions of various on-chip and on-board peripherals on various
platforms as support gets added. Some of the bigger changes are:
- Addition of (new) PCI-e support on Tegra.
- More Tegra4 support, including PMC configuration for Dalmore.
- Addition of a new board for Exynos4 (trats2) and more bindings for 4x12 IP.
- Addition of Allwinner A20 and A31 SoC and board files.
- Move of the ST Ericsson device tree files to now use ste-* prefix.
- More move of hardware description of shmobile platforms to DT.
- Two new board dts files for Freescale MXs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=1GuI
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Olof Johansson:
"Device tree and bindings updates for 3.12.
General additions of various on-chip and on-board peripherals on
various platforms as support gets added. Some of the bigger changes
are:
- Addition of (new) PCI-e support on Tegra.
- More Tegra4 support, including PMC configuration for Dalmore.
- Addition of a new board for Exynos4 (trats2) and more bindings for
4x12 IP.
- Addition of Allwinner A20 and A31 SoC and board files.
- Move of the ST Ericsson device tree files to now use ste-* prefix.
- More move of hardware description of shmobile platforms to DT.
- Two new board dts files for Freescale MXs"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (177 commits)
dts: Rename DW APB timer compatible strings
dts: Deprecate ALTR as a vendor prefix
of: add vendor prefix for Altera Corp.
ARM: at91/dt: sam9x5ek: add sound configuration
ARM: at91/dt: sam9x5ek: enable SSC
ARM: at91/dt: sam9x5ek: add WM8731 codec
ARM: at91/dt: sam9x5: add SSC DMA parameters
ARM: at91/dt: add at91rm9200 PQFP package version
ARM: at91: at91rm9200: set default mmc0 pinctrl-names
ARM: at91: at91sam9n12: correct pin number of gpio-key
ARM: at91: at91sam9n12: add qt1070 support
ARM: at91: at91sam9n12: add pinctrl of TWI
ARM: at91: Add PMU support for sama5d3
ARM: at91: at91sam9260: add missing pinctrl-names on mmc
ARM: tegra: configure power off for Dalmore
ARM: DT: binding fixup to align with vendor-prefixes.txt (DT)
ARM: dts: add sdio blocks to bcm28155-ap board
ARM: dts: align sdio numbers to HW definition
ARM: sun7i: Add Olimex A20-Olinuxino-Micro support
ARM: sun7i: Add Allwinner A20 DTSI
...
Pull Tile arch updates from Chris Metcalf:
"These changes bring in a bunch of new functionality that has been
maintained internally at Tilera over the last year, plus other stray
bits of work that I've taken into the tile tree from other folks.
The changes include some PCI root complex work, interrupt-driven
console support, support for performing fast-path unaligned data
fixups by kernel-based JIT code generation, CONFIG_PREEMPT support,
vDSO support for gettimeofday(), a serial driver for the tilegx
on-chip UART, KGDB support, more optimized string routines, support
for ftrace and kprobes, improved ASLR, and many bug fixes.
We also remove support for the old TILE64 chip, which is no longer
buildable"
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile: (85 commits)
tile: refresh tile defconfig files
tile: rework <asm/cmpxchg.h>
tile PCI RC: make default consistent DMA mask 32-bit
tile: add null check for kzalloc in tile/kernel/setup.c
tile: make __write_once a synonym for __read_mostly
tile: remove support for TILE64
tile: use asm-generic/bitops/builtin-*.h
tile: eliminate no-op "noatomichash" boot argument
tile: use standard tile_bundle_bits type in traps.c
tile: simplify code referencing hypervisor API addresses
tile: change <asm/system.h> to <asm/switch_to.h> in comments
tile: mark pcibios_init() as __init
tile: check for correct compiler earlier in asm-offsets.c
tile: use standard 'generic-y' model for <asm/hw_irq.h>
tile: use asm-generic version of <asm/local64.h>
tile PCI RC: add comment about "PCI hole" problem
tile: remove DEBUG_EXTRA_FLAGS kernel config option
tile: add virt_to_kpte() API and clean up and document behavior
tile: support FRAME_POINTER
tile: support reporting Tilera hypervisor statistics
...
Pull powerpc updates from Ben Herrenschmidt:
"Here's the powerpc batch for this merge window. Some of the
highlights are:
- A bunch of endian fixes ! We don't have full LE support yet in that
release but this contains a lot of fixes all over arch/powerpc to
use the proper accessors, call the firmware with the right endian
mode, etc...
- A few updates to our "powernv" platform (non-virtualized, the one
to run KVM on), among other, support for bridging the P8 LPC bus
for UARTs, support and some EEH fixes.
- Some mpc51xx clock API cleanups in preparation for a clock API
overhaul
- A pile of cleanups of our old math emulation code, including better
support for using it to emulate optional FP instructions on
embedded chips that otherwise have a HW FPU.
- Some infrastructure in selftest, for powerpc now, but could be
generalized, initially used by some tests for our perf instruction
counting code.
- A pile of fixes for hotplug on pseries (that was seriously
bitrotting)
- The usual slew of freescale embedded updates, new boards, 64-bit
hiberation support, e6500 core PMU support, etc..."
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (146 commits)
powerpc: Correct FSCR bit definitions
powerpc/xmon: Fix printing of set of CPUs in xmon
powerpc/pseries: Move lparcfg.c to platforms/pseries
powerpc/powernv: Return secondary CPUs to firmware on kexec
powerpc/btext: Fix CONFIG_PPC_EARLY_DEBUG_BOOTX on ppc32
powerpc: Cleanup handling of the DSCR bit in the FSCR register
powerpc/pseries: Child nodes are not detached by dlpar_detach_node
powerpc/pseries: Add mising of_node_put in delete_dt_node
powerpc/pseries: Make dlpar_configure_connector parent node aware
powerpc/pseries: Do all node initialization in dlpar_parse_cc_node
powerpc/pseries: Fix parsing of initial node path in update_dt_node
powerpc/pseries: Pack update_props_workarea to map correctly to rtas buffer header
powerpc/pseries: Fix over writing of rtas return code in update_dt_node
powerpc/pseries: Fix creation of loop in device node property list
powerpc: Skip emulating & leave interrupts off for kernel program checks
powerpc: Add more exception trampolines for hypervisor exceptions
powerpc: Fix location and rename exception trampolines
powerpc: Add more trap names to xmon
powerpc/pseries: Add a warning in the case of cross-cpu VPA registration
powerpc: Update the 00-Index in Documentation/powerpc
...
Pull trivial tree from Jiri Kosina:
"The usual trivial updates all over the tree -- mostly typo fixes and
documentation updates"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (52 commits)
doc: Documentation/cputopology.txt fix typo
treewide: Convert retrun typos to return
Fix comment typo for init_cma_reserved_pageblock
Documentation/trace: Correcting and extending tracepoint documentation
mm/hotplug: fix a typo in Documentation/memory-hotplug.txt
power: Documentation: Update s2ram link
doc: fix a typo in Documentation/00-INDEX
Documentation/printk-formats.txt: No casts needed for u64/s64
doc: Fix typo "is is" in Documentations
treewide: Fix printks with 0x%#
zram: doc fixes
Documentation/kmemcheck: update kmemcheck documentation
doc: documentation/hwspinlock.txt fix typo
PM / Hibernate: add section for resume options
doc: filesystems : Fix typo in Documentations/filesystems
scsi/megaraid fixed several typos in comments
ppc: init_32: Fix error typo "CONFIG_START_KERNEL"
treewide: Add __GFP_NOWARN to k.alloc calls with v.alloc fallbacks
page_isolation: Fix a comment typo in test_pages_isolated()
doc: fix a typo about irq affinity
...
From Anatolij:
<<
There are cleanups for some mpc5121 specific drivers and DTS files
in preparation to switch mpc5121 clock support to a clock driver
based on common clock framework. Additionally Sebastian fixed the
mpc52xx PIC driver so that it builds when using older gcc versions.
>>
Here's the big tty/serial driver pull request for 3.12-rc1.
Lots of n_tty reworks to resolve some very long-standing issues, removing the
3-4 different locks that were taken for every character. This code has been
beaten on for a long time in linux-next with no reported regressions.
Other than that, a range of serial and tty driver updates and revisions. Full
details in the shortlog.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.21 (GNU/Linux)
iEYEABECAAYFAlIlI6UACgkQMUfUDdst+ym7kgCgmysv/TVeqsdvmkiO2eEB4+xs
ddwAoMqkJ/enCJ2f+fC8y2Wz+5+kDrU7
=CiCp
-----END PGP SIGNATURE-----
Merge tag 'tty-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver patches from Greg KH:
"Here's the big tty/serial driver pull request for 3.12-rc1.
Lots of n_tty reworks to resolve some very long-standing issues,
removing the 3-4 different locks that were taken for every character.
This code has been beaten on for a long time in linux-next with no
reported regressions.
Other than that, a range of serial and tty driver updates and
revisions. Full details in the shortlog"
* tag 'tty-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (226 commits)
hvc_xen: Remove unnecessary __GFP_ZERO from kzalloc
serial: imx: initialize the local variable
tty: ar933x_uart: add device tree support and binding documentation
tty: ar933x_uart: allow to build the driver as a module
ARM: dts: msm: Update uartdm compatible strings
devicetree: serial: Document msm_serial bindings
serial: unify serial bindings into a single dir
serial: fsl-imx-uart: Cleanup duplicate device tree binding
tty: ar933x_uart: use config_enabled() macro to clean up ifdefs
tty: ar933x_uart: remove superfluous assignment of ar933x_uart_driver.nr
tty: ar933x_uart: use the clk API to get the uart clock
tty: serial: cpm_uart: Adding proper request of GPIO used by cpm_uart driver
serial: sirf: fix the amount of serial ports
serial: sirf: define macro for some magic numbers of USP
serial: icom: move array overflow checks earlier
TTY: amiserial, remove unnecessary platform_set_drvdata()
serial: st-asc: remove unnecessary platform_set_drvdata()
msm_serial: Send more than 1 character on the console w/ UARTDM
msm_serial: Add support for non-GSBI UARTDM devices
msm_serial: Switch clock consumer strings and simplify code
...
The slave_config is not initialized, so some of its fields may
be set with random data which may causes the failure in the following
dmaengine_prep_slave_sg().
This patch fixes this issue.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Modify the probe routine to get the port line number
from device tree if the 'of_node' is populated in the
platform device. The driver can be built as module,
thus add an OF specific module device table as well
to support module auto loading.
This makes it possible to use the driver for AR9330
UART devices specified in device tree.
Cc: devicetree@vger.kernel.org
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Change the SERIAL_AR933X Kconfig option from
'bool' to 'tristate' in order to allow to build
the driver as a module. Also extend the help text
of the option to reflect that.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because most of the vendor prefixes are lower case, deprecate
the vendor prefix "ALTR" in place of "altr" for Altera Corp..
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
Add a new ar933x_uart_console_enabled() helper function
which uses the config_enable(CONFIG_SERIAL_AR933X_CONSOLE)
macro to decide if the console support is enabled or not.
Remove the 'ifdef CONFIG_SERIAL_AR933X_CONSOLE' statements
and use the new helper function to conditionally enable
console support instead.
If CONFIG_SERIAL_AR933X_CONSOLE is not enabled, the new
helper function will become a null stub which allows the
compiler to optimize out the unused console specific
functions/variables.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'nr' field of the 'ar933x_uart_driver' structure
is already initialized with the same value in the static
declaration. Remove the superfluous assignment in the
module init routine.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The AR933x UARTs are only used on the Atheros AR933x
SoCs. The base clock frequency of the UART is passed
to the driver via platform data. The SoC support code
implements the generic clock API, and the clock rate
can be retrieved via that.
Update the code to get the clock rate via the generic
clock API instead of using the platform data.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cpm_uart serial driver uses GPIO for control signals. In order to be used
properly, GPIOs have to be reserved. Comment in gpiolib.c considers illegal
the use of GPIOs without requesting them. In addition, the direction of the
GPIO has to be set properly.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SiRFprimaII has three uart ports and three USP-based ports, so there
are totally six lines instead of five.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
this patch clears some magic numbers for offset and bitshift
of USP registers.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This code does an annoying thing where it writes to the array and then
checks later for array overflows. I don't know if it's actually
possible to overflow but let's check before using the array index.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We recently added support to send more than one character at a
time for UARTDM hardware but we didn't add the same support in
the console code path. Add support here to speed up console
messages on UARTDM hardware.
Cc: David Brown <davidb@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Not all UARTDM hardware is part of a GSBI complex. Add support
for these devices and fix a bug where we assumed uartdm meant the
hardware was part of a GSBI complex.
Cc: David Brown <davidb@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In downstream kernel we've standardized the clock consumer names
that MSM device drivers use. Replace the uart specific clock
names in this driver with the more standard 'core' and 'iface'
names. Also simplify the code by assuming that clk_prepare_enable
and clk_disable_unprepare() will properly check for NULL pointers
(it will because MSM uses the common clock framework).
Cc: David Brown <davidb@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current driver triggers a lockdep warning for if tty_flip_buffer_push() is
called with uart_port->lock locked. This never shows up on UP kernels and comes
up only on SMP kernels.
Crash looks like this (produced with samsung.c driver):
-----
[<c0014d58>] (unwind_backtrace+0x0/0xf8) from [<c0011908>] (show_stack+0x10/0x14)
[<c0011908>] (show_stack+0x10/0x14) from [<c035da34>] (dump_stack+0x6c/0xac)
[<c035da34>] (dump_stack+0x6c/0xac) from [<c01b59ac>] (do_raw_spin_unlock+0xc4/0xd8)
[<c01b59ac>] (do_raw_spin_unlock+0xc4/0xd8) from [<c03627e4>] (_raw_spin_unlock_irqrestore+0xc/0)
[<c03627e4>] (_raw_spin_unlock_irqrestore+0xc/0x38) from [<c020a1a8>] (s3c24xx_serial_rx_chars+0)
[<c020a1a8>] (s3c24xx_serial_rx_chars+0x12c/0x260) from [<c020aae8>] (s3c64xx_serial_handle_irq+)
[<c020aae8>] (s3c64xx_serial_handle_irq+0x48/0x60) from [<c006aaa0>] (handle_irq_event_percpu+0x)
[<c006aaa0>] (handle_irq_event_percpu+0x50/0x194) from [<c006ac20>] (handle_irq_event+0x3c/0x5c)
[<c006ac20>] (handle_irq_event+0x3c/0x5c) from [<c006d864>] (handle_fasteoi_irq+0x80/0x13c)
[<c006d864>] (handle_fasteoi_irq+0x80/0x13c) from [<c006a4a4>] (generic_handle_irq+0x20/0x30)
[<c006a4a4>] (generic_handle_irq+0x20/0x30) from [<c000f454>] (handle_IRQ+0x38/0x94)
[<c000f454>] (handle_IRQ+0x38/0x94) from [<c0008538>] (gic_handle_irq+0x34/0x68)
[<c0008538>] (gic_handle_irq+0x34/0x68) from [<c00123c0>] (__irq_svc+0x40/0x70)
Exception stack(0xc04cdf70 to 0xc04cdfb8)
df60: 00000000 00000000 0000166e 00000000
df80: c04cc000 c050278f c050278f 00000001 c04d444c 410fc0f4 c03649b0 00000000
dfa0: 00000001 c04cdfb8 c000f758 c000f75c 60070013 ffffffff
[<c00123c0>] (__irq_svc+0x40/0x70) from [<c000f75c>] (arch_cpu_idle+0x28/0x30)
[<c000f75c>] (arch_cpu_idle+0x28/0x30) from [<c0054888>] (cpu_startup_entry+0x5c/0x148)
[<c0054888>] (cpu_startup_entry+0x5c/0x148) from [<c0497aa4>] (start_kernel+0x334/0x38c)
BUG: spinlock lockup suspected on CPU#0, kworker/0:1/360
lock: s3c24xx_serial_ports+0x1d8/0x370, .magic: dead4ead, .owner: <none>/-1, .owner_cpu: -1
CPU: 0 PID: 360 Comm: kworker/0:1 Not tainted 3.11.0-rc6-next-20130819-00003-g75485f1 #2
Workqueue: events flush_to_ldisc
[<c0014d58>] (unwind_backtrace+0x0/0xf8) from [<c0011908>] (show_stack+0x10/0x14)
[<c0011908>] (show_stack+0x10/0x14) from [<c035da34>] (dump_stack+0x6c/0xac)
[<c035da34>] (dump_stack+0x6c/0xac) from [<c01b581c>] (do_raw_spin_lock+0x100/0x17c)
[<c01b581c>] (do_raw_spin_lock+0x100/0x17c) from [<c03628a0>] (_raw_spin_lock_irqsave+0x20/0x28)
[<c03628a0>] (_raw_spin_lock_irqsave+0x20/0x28) from [<c0203224>] (uart_start+0x18/0x34)
[<c0203224>] (uart_start+0x18/0x34) from [<c01ef890>] (__receive_buf+0x4b4/0x738)
[<c01ef890>] (__receive_buf+0x4b4/0x738) from [<c01efb44>] (n_tty_receive_buf2+0x30/0x98)
[<c01efb44>] (n_tty_receive_buf2+0x30/0x98) from [<c01f2ba8>] (flush_to_ldisc+0xec/0x138)
[<c01f2ba8>] (flush_to_ldisc+0xec/0x138) from [<c0031af0>] (process_one_work+0xfc/0x348)
[<c0031af0>] (process_one_work+0xfc/0x348) from [<c0032138>] (worker_thread+0x138/0x37c)
[<c0032138>] (worker_thread+0x138/0x37c) from [<c0037a7c>] (kthread+0xa4/0xb0)
[<c0037a7c>] (kthread+0xa4/0xb0) from [<c000e5f8>] (ret_from_fork+0x14/0x3c)
-----
Release the port lock before calling tty_flip_buffer_push() and reacquire it
after the call.
Similar stuff was already done for few other drivers in the past, like:
commit 2389b27216
Author: Thomas Gleixner <tglx@linutronix.de>
Date: Tue May 29 21:53:50 2007 +0100
[ARM] 4417/1: Serial: Fix AMBA drivers locking
Cc: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current driver triggers a lockdep warning for if tty_flip_buffer_push() is
called with uart_port->lock locked. This never shows up on UP kernels and comes
up only on SMP kernels.
Crash looks like this (produced with samsung.c driver):
-----
[<c0014d58>] (unwind_backtrace+0x0/0xf8) from [<c0011908>] (show_stack+0x10/0x14)
[<c0011908>] (show_stack+0x10/0x14) from [<c035da34>] (dump_stack+0x6c/0xac)
[<c035da34>] (dump_stack+0x6c/0xac) from [<c01b59ac>] (do_raw_spin_unlock+0xc4/0xd8)
[<c01b59ac>] (do_raw_spin_unlock+0xc4/0xd8) from [<c03627e4>] (_raw_spin_unlock_irqrestore+0xc/0)
[<c03627e4>] (_raw_spin_unlock_irqrestore+0xc/0x38) from [<c020a1a8>] (s3c24xx_serial_rx_chars+0)
[<c020a1a8>] (s3c24xx_serial_rx_chars+0x12c/0x260) from [<c020aae8>] (s3c64xx_serial_handle_irq+)
[<c020aae8>] (s3c64xx_serial_handle_irq+0x48/0x60) from [<c006aaa0>] (handle_irq_event_percpu+0x)
[<c006aaa0>] (handle_irq_event_percpu+0x50/0x194) from [<c006ac20>] (handle_irq_event+0x3c/0x5c)
[<c006ac20>] (handle_irq_event+0x3c/0x5c) from [<c006d864>] (handle_fasteoi_irq+0x80/0x13c)
[<c006d864>] (handle_fasteoi_irq+0x80/0x13c) from [<c006a4a4>] (generic_handle_irq+0x20/0x30)
[<c006a4a4>] (generic_handle_irq+0x20/0x30) from [<c000f454>] (handle_IRQ+0x38/0x94)
[<c000f454>] (handle_IRQ+0x38/0x94) from [<c0008538>] (gic_handle_irq+0x34/0x68)
[<c0008538>] (gic_handle_irq+0x34/0x68) from [<c00123c0>] (__irq_svc+0x40/0x70)
Exception stack(0xc04cdf70 to 0xc04cdfb8)
df60: 00000000 00000000 0000166e 00000000
df80: c04cc000 c050278f c050278f 00000001 c04d444c 410fc0f4 c03649b0 00000000
dfa0: 00000001 c04cdfb8 c000f758 c000f75c 60070013 ffffffff
[<c00123c0>] (__irq_svc+0x40/0x70) from [<c000f75c>] (arch_cpu_idle+0x28/0x30)
[<c000f75c>] (arch_cpu_idle+0x28/0x30) from [<c0054888>] (cpu_startup_entry+0x5c/0x148)
[<c0054888>] (cpu_startup_entry+0x5c/0x148) from [<c0497aa4>] (start_kernel+0x334/0x38c)
BUG: spinlock lockup suspected on CPU#0, kworker/0:1/360
lock: s3c24xx_serial_ports+0x1d8/0x370, .magic: dead4ead, .owner: <none>/-1, .owner_cpu: -1
CPU: 0 PID: 360 Comm: kworker/0:1 Not tainted 3.11.0-rc6-next-20130819-00003-g75485f1 #2
Workqueue: events flush_to_ldisc
[<c0014d58>] (unwind_backtrace+0x0/0xf8) from [<c0011908>] (show_stack+0x10/0x14)
[<c0011908>] (show_stack+0x10/0x14) from [<c035da34>] (dump_stack+0x6c/0xac)
[<c035da34>] (dump_stack+0x6c/0xac) from [<c01b581c>] (do_raw_spin_lock+0x100/0x17c)
[<c01b581c>] (do_raw_spin_lock+0x100/0x17c) from [<c03628a0>] (_raw_spin_lock_irqsave+0x20/0x28)
[<c03628a0>] (_raw_spin_lock_irqsave+0x20/0x28) from [<c0203224>] (uart_start+0x18/0x34)
[<c0203224>] (uart_start+0x18/0x34) from [<c01ef890>] (__receive_buf+0x4b4/0x738)
[<c01ef890>] (__receive_buf+0x4b4/0x738) from [<c01efb44>] (n_tty_receive_buf2+0x30/0x98)
[<c01efb44>] (n_tty_receive_buf2+0x30/0x98) from [<c01f2ba8>] (flush_to_ldisc+0xec/0x138)
[<c01f2ba8>] (flush_to_ldisc+0xec/0x138) from [<c0031af0>] (process_one_work+0xfc/0x348)
[<c0031af0>] (process_one_work+0xfc/0x348) from [<c0032138>] (worker_thread+0x138/0x37c)
[<c0032138>] (worker_thread+0x138/0x37c) from [<c0037a7c>] (kthread+0xa4/0xb0)
[<c0037a7c>] (kthread+0xa4/0xb0) from [<c000e5f8>] (ret_from_fork+0x14/0x3c)
-----
Release the port lock before calling tty_flip_buffer_push() and reacquire it
after the call.
Similar stuff was already done for few other drivers in the past, like:
commit 2389b27216
Author: Thomas Gleixner <tglx@linutronix.de>
Date: Tue May 29 21:53:50 2007 +0100
[ARM] 4417/1: Serial: Fix AMBA drivers locking
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current driver triggers a lockdep warning for if tty_flip_buffer_push() is
called with uart_port->lock locked. This never shows up on UP kernels and comes
up only on SMP kernels.
Crash looks like this (produced with samsung.c driver):
-----
[<c0014d58>] (unwind_backtrace+0x0/0xf8) from [<c0011908>] (show_stack+0x10/0x14)
[<c0011908>] (show_stack+0x10/0x14) from [<c035da34>] (dump_stack+0x6c/0xac)
[<c035da34>] (dump_stack+0x6c/0xac) from [<c01b59ac>] (do_raw_spin_unlock+0xc4/0xd8)
[<c01b59ac>] (do_raw_spin_unlock+0xc4/0xd8) from [<c03627e4>] (_raw_spin_unlock_irqrestore+0xc/0)
[<c03627e4>] (_raw_spin_unlock_irqrestore+0xc/0x38) from [<c020a1a8>] (s3c24xx_serial_rx_chars+0)
[<c020a1a8>] (s3c24xx_serial_rx_chars+0x12c/0x260) from [<c020aae8>] (s3c64xx_serial_handle_irq+)
[<c020aae8>] (s3c64xx_serial_handle_irq+0x48/0x60) from [<c006aaa0>] (handle_irq_event_percpu+0x)
[<c006aaa0>] (handle_irq_event_percpu+0x50/0x194) from [<c006ac20>] (handle_irq_event+0x3c/0x5c)
[<c006ac20>] (handle_irq_event+0x3c/0x5c) from [<c006d864>] (handle_fasteoi_irq+0x80/0x13c)
[<c006d864>] (handle_fasteoi_irq+0x80/0x13c) from [<c006a4a4>] (generic_handle_irq+0x20/0x30)
[<c006a4a4>] (generic_handle_irq+0x20/0x30) from [<c000f454>] (handle_IRQ+0x38/0x94)
[<c000f454>] (handle_IRQ+0x38/0x94) from [<c0008538>] (gic_handle_irq+0x34/0x68)
[<c0008538>] (gic_handle_irq+0x34/0x68) from [<c00123c0>] (__irq_svc+0x40/0x70)
Exception stack(0xc04cdf70 to 0xc04cdfb8)
df60: 00000000 00000000 0000166e 00000000
df80: c04cc000 c050278f c050278f 00000001 c04d444c 410fc0f4 c03649b0 00000000
dfa0: 00000001 c04cdfb8 c000f758 c000f75c 60070013 ffffffff
[<c00123c0>] (__irq_svc+0x40/0x70) from [<c000f75c>] (arch_cpu_idle+0x28/0x30)
[<c000f75c>] (arch_cpu_idle+0x28/0x30) from [<c0054888>] (cpu_startup_entry+0x5c/0x148)
[<c0054888>] (cpu_startup_entry+0x5c/0x148) from [<c0497aa4>] (start_kernel+0x334/0x38c)
BUG: spinlock lockup suspected on CPU#0, kworker/0:1/360
lock: s3c24xx_serial_ports+0x1d8/0x370, .magic: dead4ead, .owner: <none>/-1, .owner_cpu: -1
CPU: 0 PID: 360 Comm: kworker/0:1 Not tainted 3.11.0-rc6-next-20130819-00003-g75485f1 #2
Workqueue: events flush_to_ldisc
[<c0014d58>] (unwind_backtrace+0x0/0xf8) from [<c0011908>] (show_stack+0x10/0x14)
[<c0011908>] (show_stack+0x10/0x14) from [<c035da34>] (dump_stack+0x6c/0xac)
[<c035da34>] (dump_stack+0x6c/0xac) from [<c01b581c>] (do_raw_spin_lock+0x100/0x17c)
[<c01b581c>] (do_raw_spin_lock+0x100/0x17c) from [<c03628a0>] (_raw_spin_lock_irqsave+0x20/0x28)
[<c03628a0>] (_raw_spin_lock_irqsave+0x20/0x28) from [<c0203224>] (uart_start+0x18/0x34)
[<c0203224>] (uart_start+0x18/0x34) from [<c01ef890>] (__receive_buf+0x4b4/0x738)
[<c01ef890>] (__receive_buf+0x4b4/0x738) from [<c01efb44>] (n_tty_receive_buf2+0x30/0x98)
[<c01efb44>] (n_tty_receive_buf2+0x30/0x98) from [<c01f2ba8>] (flush_to_ldisc+0xec/0x138)
[<c01f2ba8>] (flush_to_ldisc+0xec/0x138) from [<c0031af0>] (process_one_work+0xfc/0x348)
[<c0031af0>] (process_one_work+0xfc/0x348) from [<c0032138>] (worker_thread+0x138/0x37c)
[<c0032138>] (worker_thread+0x138/0x37c) from [<c0037a7c>] (kthread+0xa4/0xb0)
[<c0037a7c>] (kthread+0xa4/0xb0) from [<c000e5f8>] (ret_from_fork+0x14/0x3c)
-----
Release the port lock before calling tty_flip_buffer_push() and reacquire it
after the call.
Similar stuff was already done for few other drivers in the past, like:
commit 2389b27216
Author: Thomas Gleixner <tglx@linutronix.de>
Date: Tue May 29 21:53:50 2007 +0100
[ARM] 4417/1: Serial: Fix AMBA drivers locking
Cc: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current driver triggers a lockdep warning for if tty_flip_buffer_push() is
called with uart_port->lock locked. This never shows up on UP kernels and comes
up only on SMP kernels.
Crash looks like this (produced with samsung.c driver):
-----
[<c0014d58>] (unwind_backtrace+0x0/0xf8) from [<c0011908>] (show_stack+0x10/0x14)
[<c0011908>] (show_stack+0x10/0x14) from [<c035da34>] (dump_stack+0x6c/0xac)
[<c035da34>] (dump_stack+0x6c/0xac) from [<c01b59ac>] (do_raw_spin_unlock+0xc4/0xd8)
[<c01b59ac>] (do_raw_spin_unlock+0xc4/0xd8) from [<c03627e4>] (_raw_spin_unlock_irqrestore+0xc/0)
[<c03627e4>] (_raw_spin_unlock_irqrestore+0xc/0x38) from [<c020a1a8>] (s3c24xx_serial_rx_chars+0)
[<c020a1a8>] (s3c24xx_serial_rx_chars+0x12c/0x260) from [<c020aae8>] (s3c64xx_serial_handle_irq+)
[<c020aae8>] (s3c64xx_serial_handle_irq+0x48/0x60) from [<c006aaa0>] (handle_irq_event_percpu+0x)
[<c006aaa0>] (handle_irq_event_percpu+0x50/0x194) from [<c006ac20>] (handle_irq_event+0x3c/0x5c)
[<c006ac20>] (handle_irq_event+0x3c/0x5c) from [<c006d864>] (handle_fasteoi_irq+0x80/0x13c)
[<c006d864>] (handle_fasteoi_irq+0x80/0x13c) from [<c006a4a4>] (generic_handle_irq+0x20/0x30)
[<c006a4a4>] (generic_handle_irq+0x20/0x30) from [<c000f454>] (handle_IRQ+0x38/0x94)
[<c000f454>] (handle_IRQ+0x38/0x94) from [<c0008538>] (gic_handle_irq+0x34/0x68)
[<c0008538>] (gic_handle_irq+0x34/0x68) from [<c00123c0>] (__irq_svc+0x40/0x70)
Exception stack(0xc04cdf70 to 0xc04cdfb8)
df60: 00000000 00000000 0000166e 00000000
df80: c04cc000 c050278f c050278f 00000001 c04d444c 410fc0f4 c03649b0 00000000
dfa0: 00000001 c04cdfb8 c000f758 c000f75c 60070013 ffffffff
[<c00123c0>] (__irq_svc+0x40/0x70) from [<c000f75c>] (arch_cpu_idle+0x28/0x30)
[<c000f75c>] (arch_cpu_idle+0x28/0x30) from [<c0054888>] (cpu_startup_entry+0x5c/0x148)
[<c0054888>] (cpu_startup_entry+0x5c/0x148) from [<c0497aa4>] (start_kernel+0x334/0x38c)
BUG: spinlock lockup suspected on CPU#0, kworker/0:1/360
lock: s3c24xx_serial_ports+0x1d8/0x370, .magic: dead4ead, .owner: <none>/-1, .owner_cpu: -1
CPU: 0 PID: 360 Comm: kworker/0:1 Not tainted 3.11.0-rc6-next-20130819-00003-g75485f1 #2
Workqueue: events flush_to_ldisc
[<c0014d58>] (unwind_backtrace+0x0/0xf8) from [<c0011908>] (show_stack+0x10/0x14)
[<c0011908>] (show_stack+0x10/0x14) from [<c035da34>] (dump_stack+0x6c/0xac)
[<c035da34>] (dump_stack+0x6c/0xac) from [<c01b581c>] (do_raw_spin_lock+0x100/0x17c)
[<c01b581c>] (do_raw_spin_lock+0x100/0x17c) from [<c03628a0>] (_raw_spin_lock_irqsave+0x20/0x28)
[<c03628a0>] (_raw_spin_lock_irqsave+0x20/0x28) from [<c0203224>] (uart_start+0x18/0x34)
[<c0203224>] (uart_start+0x18/0x34) from [<c01ef890>] (__receive_buf+0x4b4/0x738)
[<c01ef890>] (__receive_buf+0x4b4/0x738) from [<c01efb44>] (n_tty_receive_buf2+0x30/0x98)
[<c01efb44>] (n_tty_receive_buf2+0x30/0x98) from [<c01f2ba8>] (flush_to_ldisc+0xec/0x138)
[<c01f2ba8>] (flush_to_ldisc+0xec/0x138) from [<c0031af0>] (process_one_work+0xfc/0x348)
[<c0031af0>] (process_one_work+0xfc/0x348) from [<c0032138>] (worker_thread+0x138/0x37c)
[<c0032138>] (worker_thread+0x138/0x37c) from [<c0037a7c>] (kthread+0xa4/0xb0)
[<c0037a7c>] (kthread+0xa4/0xb0) from [<c000e5f8>] (ret_from_fork+0x14/0x3c)
-----
Release the port lock before calling tty_flip_buffer_push() and reacquire it
after the call.
Similar stuff was already done for few other drivers in the past, like:
commit 2389b27216
Author: Thomas Gleixner <tglx@linutronix.de>
Date: Tue May 29 21:53:50 2007 +0100
[ARM] 4417/1: Serial: Fix AMBA drivers locking
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current driver triggers a lockdep warning for if tty_flip_buffer_push() is
called with uart_port->lock locked. This never shows up on UP kernels and comes
up only on SMP kernels.
Crash looks like this (produced with samsung.c driver):
-----
[<c0014d58>] (unwind_backtrace+0x0/0xf8) from [<c0011908>] (show_stack+0x10/0x14)
[<c0011908>] (show_stack+0x10/0x14) from [<c035da34>] (dump_stack+0x6c/0xac)
[<c035da34>] (dump_stack+0x6c/0xac) from [<c01b59ac>] (do_raw_spin_unlock+0xc4/0xd8)
[<c01b59ac>] (do_raw_spin_unlock+0xc4/0xd8) from [<c03627e4>] (_raw_spin_unlock_irqrestore+0xc/0)
[<c03627e4>] (_raw_spin_unlock_irqrestore+0xc/0x38) from [<c020a1a8>] (s3c24xx_serial_rx_chars+0)
[<c020a1a8>] (s3c24xx_serial_rx_chars+0x12c/0x260) from [<c020aae8>] (s3c64xx_serial_handle_irq+)
[<c020aae8>] (s3c64xx_serial_handle_irq+0x48/0x60) from [<c006aaa0>] (handle_irq_event_percpu+0x)
[<c006aaa0>] (handle_irq_event_percpu+0x50/0x194) from [<c006ac20>] (handle_irq_event+0x3c/0x5c)
[<c006ac20>] (handle_irq_event+0x3c/0x5c) from [<c006d864>] (handle_fasteoi_irq+0x80/0x13c)
[<c006d864>] (handle_fasteoi_irq+0x80/0x13c) from [<c006a4a4>] (generic_handle_irq+0x20/0x30)
[<c006a4a4>] (generic_handle_irq+0x20/0x30) from [<c000f454>] (handle_IRQ+0x38/0x94)
[<c000f454>] (handle_IRQ+0x38/0x94) from [<c0008538>] (gic_handle_irq+0x34/0x68)
[<c0008538>] (gic_handle_irq+0x34/0x68) from [<c00123c0>] (__irq_svc+0x40/0x70)
Exception stack(0xc04cdf70 to 0xc04cdfb8)
df60: 00000000 00000000 0000166e 00000000
df80: c04cc000 c050278f c050278f 00000001 c04d444c 410fc0f4 c03649b0 00000000
dfa0: 00000001 c04cdfb8 c000f758 c000f75c 60070013 ffffffff
[<c00123c0>] (__irq_svc+0x40/0x70) from [<c000f75c>] (arch_cpu_idle+0x28/0x30)
[<c000f75c>] (arch_cpu_idle+0x28/0x30) from [<c0054888>] (cpu_startup_entry+0x5c/0x148)
[<c0054888>] (cpu_startup_entry+0x5c/0x148) from [<c0497aa4>] (start_kernel+0x334/0x38c)
BUG: spinlock lockup suspected on CPU#0, kworker/0:1/360
lock: s3c24xx_serial_ports+0x1d8/0x370, .magic: dead4ead, .owner: <none>/-1, .owner_cpu: -1
CPU: 0 PID: 360 Comm: kworker/0:1 Not tainted 3.11.0-rc6-next-20130819-00003-g75485f1 #2
Workqueue: events flush_to_ldisc
[<c0014d58>] (unwind_backtrace+0x0/0xf8) from [<c0011908>] (show_stack+0x10/0x14)
[<c0011908>] (show_stack+0x10/0x14) from [<c035da34>] (dump_stack+0x6c/0xac)
[<c035da34>] (dump_stack+0x6c/0xac) from [<c01b581c>] (do_raw_spin_lock+0x100/0x17c)
[<c01b581c>] (do_raw_spin_lock+0x100/0x17c) from [<c03628a0>] (_raw_spin_lock_irqsave+0x20/0x28)
[<c03628a0>] (_raw_spin_lock_irqsave+0x20/0x28) from [<c0203224>] (uart_start+0x18/0x34)
[<c0203224>] (uart_start+0x18/0x34) from [<c01ef890>] (__receive_buf+0x4b4/0x738)
[<c01ef890>] (__receive_buf+0x4b4/0x738) from [<c01efb44>] (n_tty_receive_buf2+0x30/0x98)
[<c01efb44>] (n_tty_receive_buf2+0x30/0x98) from [<c01f2ba8>] (flush_to_ldisc+0xec/0x138)
[<c01f2ba8>] (flush_to_ldisc+0xec/0x138) from [<c0031af0>] (process_one_work+0xfc/0x348)
[<c0031af0>] (process_one_work+0xfc/0x348) from [<c0032138>] (worker_thread+0x138/0x37c)
[<c0032138>] (worker_thread+0x138/0x37c) from [<c0037a7c>] (kthread+0xa4/0xb0)
[<c0037a7c>] (kthread+0xa4/0xb0) from [<c000e5f8>] (ret_from_fork+0x14/0x3c)
-----
Release the port lock before calling tty_flip_buffer_push() and reacquire it
after the call.
Similar stuff was already done for few other drivers in the past, like:
commit 2389b27216
Author: Thomas Gleixner <tglx@linutronix.de>
Date: Tue May 29 21:53:50 2007 +0100
[ARM] 4417/1: Serial: Fix AMBA drivers locking
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current driver triggers a lockdep warning for if tty_flip_buffer_push() is
called with uart_port->lock locked. This never shows up on UP kernels and comes
up only on SMP kernels.
Crash looks like this (produced with samsung.c driver):
-----
[<c0014d58>] (unwind_backtrace+0x0/0xf8) from [<c0011908>] (show_stack+0x10/0x14)
[<c0011908>] (show_stack+0x10/0x14) from [<c035da34>] (dump_stack+0x6c/0xac)
[<c035da34>] (dump_stack+0x6c/0xac) from [<c01b59ac>] (do_raw_spin_unlock+0xc4/0xd8)
[<c01b59ac>] (do_raw_spin_unlock+0xc4/0xd8) from [<c03627e4>] (_raw_spin_unlock_irqrestore+0xc/0)
[<c03627e4>] (_raw_spin_unlock_irqrestore+0xc/0x38) from [<c020a1a8>] (s3c24xx_serial_rx_chars+0)
[<c020a1a8>] (s3c24xx_serial_rx_chars+0x12c/0x260) from [<c020aae8>] (s3c64xx_serial_handle_irq+)
[<c020aae8>] (s3c64xx_serial_handle_irq+0x48/0x60) from [<c006aaa0>] (handle_irq_event_percpu+0x)
[<c006aaa0>] (handle_irq_event_percpu+0x50/0x194) from [<c006ac20>] (handle_irq_event+0x3c/0x5c)
[<c006ac20>] (handle_irq_event+0x3c/0x5c) from [<c006d864>] (handle_fasteoi_irq+0x80/0x13c)
[<c006d864>] (handle_fasteoi_irq+0x80/0x13c) from [<c006a4a4>] (generic_handle_irq+0x20/0x30)
[<c006a4a4>] (generic_handle_irq+0x20/0x30) from [<c000f454>] (handle_IRQ+0x38/0x94)
[<c000f454>] (handle_IRQ+0x38/0x94) from [<c0008538>] (gic_handle_irq+0x34/0x68)
[<c0008538>] (gic_handle_irq+0x34/0x68) from [<c00123c0>] (__irq_svc+0x40/0x70)
Exception stack(0xc04cdf70 to 0xc04cdfb8)
df60: 00000000 00000000 0000166e 00000000
df80: c04cc000 c050278f c050278f 00000001 c04d444c 410fc0f4 c03649b0 00000000
dfa0: 00000001 c04cdfb8 c000f758 c000f75c 60070013 ffffffff
[<c00123c0>] (__irq_svc+0x40/0x70) from [<c000f75c>] (arch_cpu_idle+0x28/0x30)
[<c000f75c>] (arch_cpu_idle+0x28/0x30) from [<c0054888>] (cpu_startup_entry+0x5c/0x148)
[<c0054888>] (cpu_startup_entry+0x5c/0x148) from [<c0497aa4>] (start_kernel+0x334/0x38c)
BUG: spinlock lockup suspected on CPU#0, kworker/0:1/360
lock: s3c24xx_serial_ports+0x1d8/0x370, .magic: dead4ead, .owner: <none>/-1, .owner_cpu: -1
CPU: 0 PID: 360 Comm: kworker/0:1 Not tainted 3.11.0-rc6-next-20130819-00003-g75485f1 #2
Workqueue: events flush_to_ldisc
[<c0014d58>] (unwind_backtrace+0x0/0xf8) from [<c0011908>] (show_stack+0x10/0x14)
[<c0011908>] (show_stack+0x10/0x14) from [<c035da34>] (dump_stack+0x6c/0xac)
[<c035da34>] (dump_stack+0x6c/0xac) from [<c01b581c>] (do_raw_spin_lock+0x100/0x17c)
[<c01b581c>] (do_raw_spin_lock+0x100/0x17c) from [<c03628a0>] (_raw_spin_lock_irqsave+0x20/0x28)
[<c03628a0>] (_raw_spin_lock_irqsave+0x20/0x28) from [<c0203224>] (uart_start+0x18/0x34)
[<c0203224>] (uart_start+0x18/0x34) from [<c01ef890>] (__receive_buf+0x4b4/0x738)
[<c01ef890>] (__receive_buf+0x4b4/0x738) from [<c01efb44>] (n_tty_receive_buf2+0x30/0x98)
[<c01efb44>] (n_tty_receive_buf2+0x30/0x98) from [<c01f2ba8>] (flush_to_ldisc+0xec/0x138)
[<c01f2ba8>] (flush_to_ldisc+0xec/0x138) from [<c0031af0>] (process_one_work+0xfc/0x348)
[<c0031af0>] (process_one_work+0xfc/0x348) from [<c0032138>] (worker_thread+0x138/0x37c)
[<c0032138>] (worker_thread+0x138/0x37c) from [<c0037a7c>] (kthread+0xa4/0xb0)
[<c0037a7c>] (kthread+0xa4/0xb0) from [<c000e5f8>] (ret_from_fork+0x14/0x3c)
-----
Release the port lock before calling tty_flip_buffer_push() and reacquire it
after the call.
Similar stuff was already done for few other drivers in the past, like:
commit 2389b27216
Author: Thomas Gleixner <tglx@linutronix.de>
Date: Tue May 29 21:53:50 2007 +0100
[ARM] 4417/1: Serial: Fix AMBA drivers locking
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current driver triggers a lockdep warning for if tty_flip_buffer_push() is
called with uart_port->lock locked. This never shows up on UP kernels and comes
up only on SMP kernels.
Crash looks like this (produced with samsung.c driver):
-----
[<c0014d58>] (unwind_backtrace+0x0/0xf8) from [<c0011908>] (show_stack+0x10/0x14)
[<c0011908>] (show_stack+0x10/0x14) from [<c035da34>] (dump_stack+0x6c/0xac)
[<c035da34>] (dump_stack+0x6c/0xac) from [<c01b59ac>] (do_raw_spin_unlock+0xc4/0xd8)
[<c01b59ac>] (do_raw_spin_unlock+0xc4/0xd8) from [<c03627e4>] (_raw_spin_unlock_irqrestore+0xc/0)
[<c03627e4>] (_raw_spin_unlock_irqrestore+0xc/0x38) from [<c020a1a8>] (s3c24xx_serial_rx_chars+0)
[<c020a1a8>] (s3c24xx_serial_rx_chars+0x12c/0x260) from [<c020aae8>] (s3c64xx_serial_handle_irq+)
[<c020aae8>] (s3c64xx_serial_handle_irq+0x48/0x60) from [<c006aaa0>] (handle_irq_event_percpu+0x)
[<c006aaa0>] (handle_irq_event_percpu+0x50/0x194) from [<c006ac20>] (handle_irq_event+0x3c/0x5c)
[<c006ac20>] (handle_irq_event+0x3c/0x5c) from [<c006d864>] (handle_fasteoi_irq+0x80/0x13c)
[<c006d864>] (handle_fasteoi_irq+0x80/0x13c) from [<c006a4a4>] (generic_handle_irq+0x20/0x30)
[<c006a4a4>] (generic_handle_irq+0x20/0x30) from [<c000f454>] (handle_IRQ+0x38/0x94)
[<c000f454>] (handle_IRQ+0x38/0x94) from [<c0008538>] (gic_handle_irq+0x34/0x68)
[<c0008538>] (gic_handle_irq+0x34/0x68) from [<c00123c0>] (__irq_svc+0x40/0x70)
Exception stack(0xc04cdf70 to 0xc04cdfb8)
df60: 00000000 00000000 0000166e 00000000
df80: c04cc000 c050278f c050278f 00000001 c04d444c 410fc0f4 c03649b0 00000000
dfa0: 00000001 c04cdfb8 c000f758 c000f75c 60070013 ffffffff
[<c00123c0>] (__irq_svc+0x40/0x70) from [<c000f75c>] (arch_cpu_idle+0x28/0x30)
[<c000f75c>] (arch_cpu_idle+0x28/0x30) from [<c0054888>] (cpu_startup_entry+0x5c/0x148)
[<c0054888>] (cpu_startup_entry+0x5c/0x148) from [<c0497aa4>] (start_kernel+0x334/0x38c)
BUG: spinlock lockup suspected on CPU#0, kworker/0:1/360
lock: s3c24xx_serial_ports+0x1d8/0x370, .magic: dead4ead, .owner: <none>/-1, .owner_cpu: -1
CPU: 0 PID: 360 Comm: kworker/0:1 Not tainted 3.11.0-rc6-next-20130819-00003-g75485f1 #2
Workqueue: events flush_to_ldisc
[<c0014d58>] (unwind_backtrace+0x0/0xf8) from [<c0011908>] (show_stack+0x10/0x14)
[<c0011908>] (show_stack+0x10/0x14) from [<c035da34>] (dump_stack+0x6c/0xac)
[<c035da34>] (dump_stack+0x6c/0xac) from [<c01b581c>] (do_raw_spin_lock+0x100/0x17c)
[<c01b581c>] (do_raw_spin_lock+0x100/0x17c) from [<c03628a0>] (_raw_spin_lock_irqsave+0x20/0x28)
[<c03628a0>] (_raw_spin_lock_irqsave+0x20/0x28) from [<c0203224>] (uart_start+0x18/0x34)
[<c0203224>] (uart_start+0x18/0x34) from [<c01ef890>] (__receive_buf+0x4b4/0x738)
[<c01ef890>] (__receive_buf+0x4b4/0x738) from [<c01efb44>] (n_tty_receive_buf2+0x30/0x98)
[<c01efb44>] (n_tty_receive_buf2+0x30/0x98) from [<c01f2ba8>] (flush_to_ldisc+0xec/0x138)
[<c01f2ba8>] (flush_to_ldisc+0xec/0x138) from [<c0031af0>] (process_one_work+0xfc/0x348)
[<c0031af0>] (process_one_work+0xfc/0x348) from [<c0032138>] (worker_thread+0x138/0x37c)
[<c0032138>] (worker_thread+0x138/0x37c) from [<c0037a7c>] (kthread+0xa4/0xb0)
[<c0037a7c>] (kthread+0xa4/0xb0) from [<c000e5f8>] (ret_from_fork+0x14/0x3c)
-----
Release the port lock before calling tty_flip_buffer_push() and reacquire it
after the call.
Similar stuff was already done for few other drivers in the past, like:
commit 2389b27216
Author: Thomas Gleixner <tglx@linutronix.de>
Date: Tue May 29 21:53:50 2007 +0100
[ARM] 4417/1: Serial: Fix AMBA drivers locking
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current driver triggers a lockdep warning for if tty_flip_buffer_push() is
called with uart_port->lock locked. This never shows up on UP kernels and comes
up only on SMP kernels.
Crash looks like this (produced with samsung.c driver):
-----
[<c0014d58>] (unwind_backtrace+0x0/0xf8) from [<c0011908>] (show_stack+0x10/0x14)
[<c0011908>] (show_stack+0x10/0x14) from [<c035da34>] (dump_stack+0x6c/0xac)
[<c035da34>] (dump_stack+0x6c/0xac) from [<c01b59ac>] (do_raw_spin_unlock+0xc4/0xd8)
[<c01b59ac>] (do_raw_spin_unlock+0xc4/0xd8) from [<c03627e4>] (_raw_spin_unlock_irqrestore+0xc/0)
[<c03627e4>] (_raw_spin_unlock_irqrestore+0xc/0x38) from [<c020a1a8>] (s3c24xx_serial_rx_chars+0)
[<c020a1a8>] (s3c24xx_serial_rx_chars+0x12c/0x260) from [<c020aae8>] (s3c64xx_serial_handle_irq+)
[<c020aae8>] (s3c64xx_serial_handle_irq+0x48/0x60) from [<c006aaa0>] (handle_irq_event_percpu+0x)
[<c006aaa0>] (handle_irq_event_percpu+0x50/0x194) from [<c006ac20>] (handle_irq_event+0x3c/0x5c)
[<c006ac20>] (handle_irq_event+0x3c/0x5c) from [<c006d864>] (handle_fasteoi_irq+0x80/0x13c)
[<c006d864>] (handle_fasteoi_irq+0x80/0x13c) from [<c006a4a4>] (generic_handle_irq+0x20/0x30)
[<c006a4a4>] (generic_handle_irq+0x20/0x30) from [<c000f454>] (handle_IRQ+0x38/0x94)
[<c000f454>] (handle_IRQ+0x38/0x94) from [<c0008538>] (gic_handle_irq+0x34/0x68)
[<c0008538>] (gic_handle_irq+0x34/0x68) from [<c00123c0>] (__irq_svc+0x40/0x70)
Exception stack(0xc04cdf70 to 0xc04cdfb8)
df60: 00000000 00000000 0000166e 00000000
df80: c04cc000 c050278f c050278f 00000001 c04d444c 410fc0f4 c03649b0 00000000
dfa0: 00000001 c04cdfb8 c000f758 c000f75c 60070013 ffffffff
[<c00123c0>] (__irq_svc+0x40/0x70) from [<c000f75c>] (arch_cpu_idle+0x28/0x30)
[<c000f75c>] (arch_cpu_idle+0x28/0x30) from [<c0054888>] (cpu_startup_entry+0x5c/0x148)
[<c0054888>] (cpu_startup_entry+0x5c/0x148) from [<c0497aa4>] (start_kernel+0x334/0x38c)
BUG: spinlock lockup suspected on CPU#0, kworker/0:1/360
lock: s3c24xx_serial_ports+0x1d8/0x370, .magic: dead4ead, .owner: <none>/-1, .owner_cpu: -1
CPU: 0 PID: 360 Comm: kworker/0:1 Not tainted 3.11.0-rc6-next-20130819-00003-g75485f1 #2
Workqueue: events flush_to_ldisc
[<c0014d58>] (unwind_backtrace+0x0/0xf8) from [<c0011908>] (show_stack+0x10/0x14)
[<c0011908>] (show_stack+0x10/0x14) from [<c035da34>] (dump_stack+0x6c/0xac)
[<c035da34>] (dump_stack+0x6c/0xac) from [<c01b581c>] (do_raw_spin_lock+0x100/0x17c)
[<c01b581c>] (do_raw_spin_lock+0x100/0x17c) from [<c03628a0>] (_raw_spin_lock_irqsave+0x20/0x28)
[<c03628a0>] (_raw_spin_lock_irqsave+0x20/0x28) from [<c0203224>] (uart_start+0x18/0x34)
[<c0203224>] (uart_start+0x18/0x34) from [<c01ef890>] (__receive_buf+0x4b4/0x738)
[<c01ef890>] (__receive_buf+0x4b4/0x738) from [<c01efb44>] (n_tty_receive_buf2+0x30/0x98)
[<c01efb44>] (n_tty_receive_buf2+0x30/0x98) from [<c01f2ba8>] (flush_to_ldisc+0xec/0x138)
[<c01f2ba8>] (flush_to_ldisc+0xec/0x138) from [<c0031af0>] (process_one_work+0xfc/0x348)
[<c0031af0>] (process_one_work+0xfc/0x348) from [<c0032138>] (worker_thread+0x138/0x37c)
[<c0032138>] (worker_thread+0x138/0x37c) from [<c0037a7c>] (kthread+0xa4/0xb0)
[<c0037a7c>] (kthread+0xa4/0xb0) from [<c000e5f8>] (ret_from_fork+0x14/0x3c)
-----
Release the port lock before calling tty_flip_buffer_push() and reacquire it
after the call.
Similar stuff was already done for few other drivers in the past, like:
commit 2389b27216
Author: Thomas Gleixner <tglx@linutronix.de>
Date: Tue May 29 21:53:50 2007 +0100
[ARM] 4417/1: Serial: Fix AMBA drivers locking
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current driver triggers a lockdep warning for if tty_flip_buffer_push() is
called with uart_port->lock locked. This never shows up on UP kernels and comes
up only on SMP kernels.
Crash looks like this (produced with samsung.c driver):
-----
[<c0014d58>] (unwind_backtrace+0x0/0xf8) from [<c0011908>] (show_stack+0x10/0x14)
[<c0011908>] (show_stack+0x10/0x14) from [<c035da34>] (dump_stack+0x6c/0xac)
[<c035da34>] (dump_stack+0x6c/0xac) from [<c01b59ac>] (do_raw_spin_unlock+0xc4/0xd8)
[<c01b59ac>] (do_raw_spin_unlock+0xc4/0xd8) from [<c03627e4>] (_raw_spin_unlock_irqrestore+0xc/0)
[<c03627e4>] (_raw_spin_unlock_irqrestore+0xc/0x38) from [<c020a1a8>] (s3c24xx_serial_rx_chars+0)
[<c020a1a8>] (s3c24xx_serial_rx_chars+0x12c/0x260) from [<c020aae8>] (s3c64xx_serial_handle_irq+)
[<c020aae8>] (s3c64xx_serial_handle_irq+0x48/0x60) from [<c006aaa0>] (handle_irq_event_percpu+0x)
[<c006aaa0>] (handle_irq_event_percpu+0x50/0x194) from [<c006ac20>] (handle_irq_event+0x3c/0x5c)
[<c006ac20>] (handle_irq_event+0x3c/0x5c) from [<c006d864>] (handle_fasteoi_irq+0x80/0x13c)
[<c006d864>] (handle_fasteoi_irq+0x80/0x13c) from [<c006a4a4>] (generic_handle_irq+0x20/0x30)
[<c006a4a4>] (generic_handle_irq+0x20/0x30) from [<c000f454>] (handle_IRQ+0x38/0x94)
[<c000f454>] (handle_IRQ+0x38/0x94) from [<c0008538>] (gic_handle_irq+0x34/0x68)
[<c0008538>] (gic_handle_irq+0x34/0x68) from [<c00123c0>] (__irq_svc+0x40/0x70)
Exception stack(0xc04cdf70 to 0xc04cdfb8)
df60: 00000000 00000000 0000166e 00000000
df80: c04cc000 c050278f c050278f 00000001 c04d444c 410fc0f4 c03649b0 00000000
dfa0: 00000001 c04cdfb8 c000f758 c000f75c 60070013 ffffffff
[<c00123c0>] (__irq_svc+0x40/0x70) from [<c000f75c>] (arch_cpu_idle+0x28/0x30)
[<c000f75c>] (arch_cpu_idle+0x28/0x30) from [<c0054888>] (cpu_startup_entry+0x5c/0x148)
[<c0054888>] (cpu_startup_entry+0x5c/0x148) from [<c0497aa4>] (start_kernel+0x334/0x38c)
BUG: spinlock lockup suspected on CPU#0, kworker/0:1/360
lock: s3c24xx_serial_ports+0x1d8/0x370, .magic: dead4ead, .owner: <none>/-1, .owner_cpu: -1
CPU: 0 PID: 360 Comm: kworker/0:1 Not tainted 3.11.0-rc6-next-20130819-00003-g75485f1 #2
Workqueue: events flush_to_ldisc
[<c0014d58>] (unwind_backtrace+0x0/0xf8) from [<c0011908>] (show_stack+0x10/0x14)
[<c0011908>] (show_stack+0x10/0x14) from [<c035da34>] (dump_stack+0x6c/0xac)
[<c035da34>] (dump_stack+0x6c/0xac) from [<c01b581c>] (do_raw_spin_lock+0x100/0x17c)
[<c01b581c>] (do_raw_spin_lock+0x100/0x17c) from [<c03628a0>] (_raw_spin_lock_irqsave+0x20/0x28)
[<c03628a0>] (_raw_spin_lock_irqsave+0x20/0x28) from [<c0203224>] (uart_start+0x18/0x34)
[<c0203224>] (uart_start+0x18/0x34) from [<c01ef890>] (__receive_buf+0x4b4/0x738)
[<c01ef890>] (__receive_buf+0x4b4/0x738) from [<c01efb44>] (n_tty_receive_buf2+0x30/0x98)
[<c01efb44>] (n_tty_receive_buf2+0x30/0x98) from [<c01f2ba8>] (flush_to_ldisc+0xec/0x138)
[<c01f2ba8>] (flush_to_ldisc+0xec/0x138) from [<c0031af0>] (process_one_work+0xfc/0x348)
[<c0031af0>] (process_one_work+0xfc/0x348) from [<c0032138>] (worker_thread+0x138/0x37c)
[<c0032138>] (worker_thread+0x138/0x37c) from [<c0037a7c>] (kthread+0xa4/0xb0)
[<c0037a7c>] (kthread+0xa4/0xb0) from [<c000e5f8>] (ret_from_fork+0x14/0x3c)
-----
Release the port lock before calling tty_flip_buffer_push() and reacquire it
after the call.
Similar stuff was already done for few other drivers in the past, like:
commit 2389b27216
Author: Thomas Gleixner <tglx@linutronix.de>
Date: Tue May 29 21:53:50 2007 +0100
[ARM] 4417/1: Serial: Fix AMBA drivers locking
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current driver triggers a lockdep warning for if tty_flip_buffer_push() is
called with uart_port->lock locked. This never shows up on UP kernels and comes
up only on SMP kernels.
Crash looks like this (produced with samsung.c driver):
-----
[<c0014d58>] (unwind_backtrace+0x0/0xf8) from [<c0011908>] (show_stack+0x10/0x14)
[<c0011908>] (show_stack+0x10/0x14) from [<c035da34>] (dump_stack+0x6c/0xac)
[<c035da34>] (dump_stack+0x6c/0xac) from [<c01b59ac>] (do_raw_spin_unlock+0xc4/0xd8)
[<c01b59ac>] (do_raw_spin_unlock+0xc4/0xd8) from [<c03627e4>] (_raw_spin_unlock_irqrestore+0xc/0)
[<c03627e4>] (_raw_spin_unlock_irqrestore+0xc/0x38) from [<c020a1a8>] (s3c24xx_serial_rx_chars+0)
[<c020a1a8>] (s3c24xx_serial_rx_chars+0x12c/0x260) from [<c020aae8>] (s3c64xx_serial_handle_irq+)
[<c020aae8>] (s3c64xx_serial_handle_irq+0x48/0x60) from [<c006aaa0>] (handle_irq_event_percpu+0x)
[<c006aaa0>] (handle_irq_event_percpu+0x50/0x194) from [<c006ac20>] (handle_irq_event+0x3c/0x5c)
[<c006ac20>] (handle_irq_event+0x3c/0x5c) from [<c006d864>] (handle_fasteoi_irq+0x80/0x13c)
[<c006d864>] (handle_fasteoi_irq+0x80/0x13c) from [<c006a4a4>] (generic_handle_irq+0x20/0x30)
[<c006a4a4>] (generic_handle_irq+0x20/0x30) from [<c000f454>] (handle_IRQ+0x38/0x94)
[<c000f454>] (handle_IRQ+0x38/0x94) from [<c0008538>] (gic_handle_irq+0x34/0x68)
[<c0008538>] (gic_handle_irq+0x34/0x68) from [<c00123c0>] (__irq_svc+0x40/0x70)
Exception stack(0xc04cdf70 to 0xc04cdfb8)
df60: 00000000 00000000 0000166e 00000000
df80: c04cc000 c050278f c050278f 00000001 c04d444c 410fc0f4 c03649b0 00000000
dfa0: 00000001 c04cdfb8 c000f758 c000f75c 60070013 ffffffff
[<c00123c0>] (__irq_svc+0x40/0x70) from [<c000f75c>] (arch_cpu_idle+0x28/0x30)
[<c000f75c>] (arch_cpu_idle+0x28/0x30) from [<c0054888>] (cpu_startup_entry+0x5c/0x148)
[<c0054888>] (cpu_startup_entry+0x5c/0x148) from [<c0497aa4>] (start_kernel+0x334/0x38c)
BUG: spinlock lockup suspected on CPU#0, kworker/0:1/360
lock: s3c24xx_serial_ports+0x1d8/0x370, .magic: dead4ead, .owner: <none>/-1, .owner_cpu: -1
CPU: 0 PID: 360 Comm: kworker/0:1 Not tainted 3.11.0-rc6-next-20130819-00003-g75485f1 #2
Workqueue: events flush_to_ldisc
[<c0014d58>] (unwind_backtrace+0x0/0xf8) from [<c0011908>] (show_stack+0x10/0x14)
[<c0011908>] (show_stack+0x10/0x14) from [<c035da34>] (dump_stack+0x6c/0xac)
[<c035da34>] (dump_stack+0x6c/0xac) from [<c01b581c>] (do_raw_spin_lock+0x100/0x17c)
[<c01b581c>] (do_raw_spin_lock+0x100/0x17c) from [<c03628a0>] (_raw_spin_lock_irqsave+0x20/0x28)
[<c03628a0>] (_raw_spin_lock_irqsave+0x20/0x28) from [<c0203224>] (uart_start+0x18/0x34)
[<c0203224>] (uart_start+0x18/0x34) from [<c01ef890>] (__receive_buf+0x4b4/0x738)
[<c01ef890>] (__receive_buf+0x4b4/0x738) from [<c01efb44>] (n_tty_receive_buf2+0x30/0x98)
[<c01efb44>] (n_tty_receive_buf2+0x30/0x98) from [<c01f2ba8>] (flush_to_ldisc+0xec/0x138)
[<c01f2ba8>] (flush_to_ldisc+0xec/0x138) from [<c0031af0>] (process_one_work+0xfc/0x348)
[<c0031af0>] (process_one_work+0xfc/0x348) from [<c0032138>] (worker_thread+0x138/0x37c)
[<c0032138>] (worker_thread+0x138/0x37c) from [<c0037a7c>] (kthread+0xa4/0xb0)
[<c0037a7c>] (kthread+0xa4/0xb0) from [<c000e5f8>] (ret_from_fork+0x14/0x3c)
-----
Release the port lock before calling tty_flip_buffer_push() and reacquire it
after the call.
Similar stuff was already done for few other drivers in the past, like:
commit 2389b27216
Author: Thomas Gleixner <tglx@linutronix.de>
Date: Tue May 29 21:53:50 2007 +0100
[ARM] 4417/1: Serial: Fix AMBA drivers locking
Cc: David Brown <davidb@codeaurora.org> (maintainer:ARM/QUALCOMM MSM...)
Cc: Daniel Walker <dwalker@fifo99.com> (maintainer:ARM/QUALCOMM MSM...)
Cc: Bryan Huntsman <bryanh@codeaurora.org> (maintainer:ARM/QUALCOMM MSM...)
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current driver triggers a lockdep warning for if tty_flip_buffer_push() is
called with uart_port->lock locked. This never shows up on UP kernels and comes
up only on SMP kernels.
Crash looks like this (produced with samsung.c driver):
-----
[<c0014d58>] (unwind_backtrace+0x0/0xf8) from [<c0011908>] (show_stack+0x10/0x14)
[<c0011908>] (show_stack+0x10/0x14) from [<c035da34>] (dump_stack+0x6c/0xac)
[<c035da34>] (dump_stack+0x6c/0xac) from [<c01b59ac>] (do_raw_spin_unlock+0xc4/0xd8)
[<c01b59ac>] (do_raw_spin_unlock+0xc4/0xd8) from [<c03627e4>] (_raw_spin_unlock_irqrestore+0xc/0)
[<c03627e4>] (_raw_spin_unlock_irqrestore+0xc/0x38) from [<c020a1a8>] (s3c24xx_serial_rx_chars+0)
[<c020a1a8>] (s3c24xx_serial_rx_chars+0x12c/0x260) from [<c020aae8>] (s3c64xx_serial_handle_irq+)
[<c020aae8>] (s3c64xx_serial_handle_irq+0x48/0x60) from [<c006aaa0>] (handle_irq_event_percpu+0x)
[<c006aaa0>] (handle_irq_event_percpu+0x50/0x194) from [<c006ac20>] (handle_irq_event+0x3c/0x5c)
[<c006ac20>] (handle_irq_event+0x3c/0x5c) from [<c006d864>] (handle_fasteoi_irq+0x80/0x13c)
[<c006d864>] (handle_fasteoi_irq+0x80/0x13c) from [<c006a4a4>] (generic_handle_irq+0x20/0x30)
[<c006a4a4>] (generic_handle_irq+0x20/0x30) from [<c000f454>] (handle_IRQ+0x38/0x94)
[<c000f454>] (handle_IRQ+0x38/0x94) from [<c0008538>] (gic_handle_irq+0x34/0x68)
[<c0008538>] (gic_handle_irq+0x34/0x68) from [<c00123c0>] (__irq_svc+0x40/0x70)
Exception stack(0xc04cdf70 to 0xc04cdfb8)
df60: 00000000 00000000 0000166e 00000000
df80: c04cc000 c050278f c050278f 00000001 c04d444c 410fc0f4 c03649b0 00000000
dfa0: 00000001 c04cdfb8 c000f758 c000f75c 60070013 ffffffff
[<c00123c0>] (__irq_svc+0x40/0x70) from [<c000f75c>] (arch_cpu_idle+0x28/0x30)
[<c000f75c>] (arch_cpu_idle+0x28/0x30) from [<c0054888>] (cpu_startup_entry+0x5c/0x148)
[<c0054888>] (cpu_startup_entry+0x5c/0x148) from [<c0497aa4>] (start_kernel+0x334/0x38c)
BUG: spinlock lockup suspected on CPU#0, kworker/0:1/360
lock: s3c24xx_serial_ports+0x1d8/0x370, .magic: dead4ead, .owner: <none>/-1, .owner_cpu: -1
CPU: 0 PID: 360 Comm: kworker/0:1 Not tainted 3.11.0-rc6-next-20130819-00003-g75485f1 #2
Workqueue: events flush_to_ldisc
[<c0014d58>] (unwind_backtrace+0x0/0xf8) from [<c0011908>] (show_stack+0x10/0x14)
[<c0011908>] (show_stack+0x10/0x14) from [<c035da34>] (dump_stack+0x6c/0xac)
[<c035da34>] (dump_stack+0x6c/0xac) from [<c01b581c>] (do_raw_spin_lock+0x100/0x17c)
[<c01b581c>] (do_raw_spin_lock+0x100/0x17c) from [<c03628a0>] (_raw_spin_lock_irqsave+0x20/0x28)
[<c03628a0>] (_raw_spin_lock_irqsave+0x20/0x28) from [<c0203224>] (uart_start+0x18/0x34)
[<c0203224>] (uart_start+0x18/0x34) from [<c01ef890>] (__receive_buf+0x4b4/0x738)
[<c01ef890>] (__receive_buf+0x4b4/0x738) from [<c01efb44>] (n_tty_receive_buf2+0x30/0x98)
[<c01efb44>] (n_tty_receive_buf2+0x30/0x98) from [<c01f2ba8>] (flush_to_ldisc+0xec/0x138)
[<c01f2ba8>] (flush_to_ldisc+0xec/0x138) from [<c0031af0>] (process_one_work+0xfc/0x348)
[<c0031af0>] (process_one_work+0xfc/0x348) from [<c0032138>] (worker_thread+0x138/0x37c)
[<c0032138>] (worker_thread+0x138/0x37c) from [<c0037a7c>] (kthread+0xa4/0xb0)
[<c0037a7c>] (kthread+0xa4/0xb0) from [<c000e5f8>] (ret_from_fork+0x14/0x3c)
-----
Release the port lock before calling tty_flip_buffer_push() and reacquire it
after the call.
Similar stuff was already done for few other drivers in the past, like:
commit 2389b27216
Author: Thomas Gleixner <tglx@linutronix.de>
Date: Tue May 29 21:53:50 2007 +0100
[ARM] 4417/1: Serial: Fix AMBA drivers locking
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current driver triggers a lockdep warning for if tty_flip_buffer_push() is
called with uart_port->lock locked. This never shows up on UP kernels and comes
up only on SMP kernels.
Crash looks like this (produced with samsung.c driver):
-----
[<c0014d58>] (unwind_backtrace+0x0/0xf8) from [<c0011908>] (show_stack+0x10/0x14)
[<c0011908>] (show_stack+0x10/0x14) from [<c035da34>] (dump_stack+0x6c/0xac)
[<c035da34>] (dump_stack+0x6c/0xac) from [<c01b59ac>] (do_raw_spin_unlock+0xc4/0xd8)
[<c01b59ac>] (do_raw_spin_unlock+0xc4/0xd8) from [<c03627e4>] (_raw_spin_unlock_irqrestore+0xc/0)
[<c03627e4>] (_raw_spin_unlock_irqrestore+0xc/0x38) from [<c020a1a8>] (s3c24xx_serial_rx_chars+0)
[<c020a1a8>] (s3c24xx_serial_rx_chars+0x12c/0x260) from [<c020aae8>] (s3c64xx_serial_handle_irq+)
[<c020aae8>] (s3c64xx_serial_handle_irq+0x48/0x60) from [<c006aaa0>] (handle_irq_event_percpu+0x)
[<c006aaa0>] (handle_irq_event_percpu+0x50/0x194) from [<c006ac20>] (handle_irq_event+0x3c/0x5c)
[<c006ac20>] (handle_irq_event+0x3c/0x5c) from [<c006d864>] (handle_fasteoi_irq+0x80/0x13c)
[<c006d864>] (handle_fasteoi_irq+0x80/0x13c) from [<c006a4a4>] (generic_handle_irq+0x20/0x30)
[<c006a4a4>] (generic_handle_irq+0x20/0x30) from [<c000f454>] (handle_IRQ+0x38/0x94)
[<c000f454>] (handle_IRQ+0x38/0x94) from [<c0008538>] (gic_handle_irq+0x34/0x68)
[<c0008538>] (gic_handle_irq+0x34/0x68) from [<c00123c0>] (__irq_svc+0x40/0x70)
Exception stack(0xc04cdf70 to 0xc04cdfb8)
df60: 00000000 00000000 0000166e 00000000
df80: c04cc000 c050278f c050278f 00000001 c04d444c 410fc0f4 c03649b0 00000000
dfa0: 00000001 c04cdfb8 c000f758 c000f75c 60070013 ffffffff
[<c00123c0>] (__irq_svc+0x40/0x70) from [<c000f75c>] (arch_cpu_idle+0x28/0x30)
[<c000f75c>] (arch_cpu_idle+0x28/0x30) from [<c0054888>] (cpu_startup_entry+0x5c/0x148)
[<c0054888>] (cpu_startup_entry+0x5c/0x148) from [<c0497aa4>] (start_kernel+0x334/0x38c)
BUG: spinlock lockup suspected on CPU#0, kworker/0:1/360
lock: s3c24xx_serial_ports+0x1d8/0x370, .magic: dead4ead, .owner: <none>/-1, .owner_cpu: -1
CPU: 0 PID: 360 Comm: kworker/0:1 Not tainted 3.11.0-rc6-next-20130819-00003-g75485f1 #2
Workqueue: events flush_to_ldisc
[<c0014d58>] (unwind_backtrace+0x0/0xf8) from [<c0011908>] (show_stack+0x10/0x14)
[<c0011908>] (show_stack+0x10/0x14) from [<c035da34>] (dump_stack+0x6c/0xac)
[<c035da34>] (dump_stack+0x6c/0xac) from [<c01b581c>] (do_raw_spin_lock+0x100/0x17c)
[<c01b581c>] (do_raw_spin_lock+0x100/0x17c) from [<c03628a0>] (_raw_spin_lock_irqsave+0x20/0x28)
[<c03628a0>] (_raw_spin_lock_irqsave+0x20/0x28) from [<c0203224>] (uart_start+0x18/0x34)
[<c0203224>] (uart_start+0x18/0x34) from [<c01ef890>] (__receive_buf+0x4b4/0x738)
[<c01ef890>] (__receive_buf+0x4b4/0x738) from [<c01efb44>] (n_tty_receive_buf2+0x30/0x98)
[<c01efb44>] (n_tty_receive_buf2+0x30/0x98) from [<c01f2ba8>] (flush_to_ldisc+0xec/0x138)
[<c01f2ba8>] (flush_to_ldisc+0xec/0x138) from [<c0031af0>] (process_one_work+0xfc/0x348)
[<c0031af0>] (process_one_work+0xfc/0x348) from [<c0032138>] (worker_thread+0x138/0x37c)
[<c0032138>] (worker_thread+0x138/0x37c) from [<c0037a7c>] (kthread+0xa4/0xb0)
[<c0037a7c>] (kthread+0xa4/0xb0) from [<c000e5f8>] (ret_from_fork+0x14/0x3c)
-----
Release the port lock before calling tty_flip_buffer_push() and reacquire it
after the call.
Similar stuff was already done for few other drivers in the past, like:
commit 2389b27216
Author: Thomas Gleixner <tglx@linutronix.de>
Date: Tue May 29 21:53:50 2007 +0100
[ARM] 4417/1: Serial: Fix AMBA drivers locking
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current driver triggers a lockdep warning for if tty_flip_buffer_push() is
called with uart_port->lock locked. This never shows up on UP kernels and comes
up only on SMP kernels.
Crash looks like this (produced with samsung.c driver):
-----
[<c0014d58>] (unwind_backtrace+0x0/0xf8) from [<c0011908>] (show_stack+0x10/0x14)
[<c0011908>] (show_stack+0x10/0x14) from [<c035da34>] (dump_stack+0x6c/0xac)
[<c035da34>] (dump_stack+0x6c/0xac) from [<c01b59ac>] (do_raw_spin_unlock+0xc4/0xd8)
[<c01b59ac>] (do_raw_spin_unlock+0xc4/0xd8) from [<c03627e4>] (_raw_spin_unlock_irqrestore+0xc/0)
[<c03627e4>] (_raw_spin_unlock_irqrestore+0xc/0x38) from [<c020a1a8>] (s3c24xx_serial_rx_chars+0)
[<c020a1a8>] (s3c24xx_serial_rx_chars+0x12c/0x260) from [<c020aae8>] (s3c64xx_serial_handle_irq+)
[<c020aae8>] (s3c64xx_serial_handle_irq+0x48/0x60) from [<c006aaa0>] (handle_irq_event_percpu+0x)
[<c006aaa0>] (handle_irq_event_percpu+0x50/0x194) from [<c006ac20>] (handle_irq_event+0x3c/0x5c)
[<c006ac20>] (handle_irq_event+0x3c/0x5c) from [<c006d864>] (handle_fasteoi_irq+0x80/0x13c)
[<c006d864>] (handle_fasteoi_irq+0x80/0x13c) from [<c006a4a4>] (generic_handle_irq+0x20/0x30)
[<c006a4a4>] (generic_handle_irq+0x20/0x30) from [<c000f454>] (handle_IRQ+0x38/0x94)
[<c000f454>] (handle_IRQ+0x38/0x94) from [<c0008538>] (gic_handle_irq+0x34/0x68)
[<c0008538>] (gic_handle_irq+0x34/0x68) from [<c00123c0>] (__irq_svc+0x40/0x70)
Exception stack(0xc04cdf70 to 0xc04cdfb8)
df60: 00000000 00000000 0000166e 00000000
df80: c04cc000 c050278f c050278f 00000001 c04d444c 410fc0f4 c03649b0 00000000
dfa0: 00000001 c04cdfb8 c000f758 c000f75c 60070013 ffffffff
[<c00123c0>] (__irq_svc+0x40/0x70) from [<c000f75c>] (arch_cpu_idle+0x28/0x30)
[<c000f75c>] (arch_cpu_idle+0x28/0x30) from [<c0054888>] (cpu_startup_entry+0x5c/0x148)
[<c0054888>] (cpu_startup_entry+0x5c/0x148) from [<c0497aa4>] (start_kernel+0x334/0x38c)
BUG: spinlock lockup suspected on CPU#0, kworker/0:1/360
lock: s3c24xx_serial_ports+0x1d8/0x370, .magic: dead4ead, .owner: <none>/-1, .owner_cpu: -1
CPU: 0 PID: 360 Comm: kworker/0:1 Not tainted 3.11.0-rc6-next-20130819-00003-g75485f1 #2
Workqueue: events flush_to_ldisc
[<c0014d58>] (unwind_backtrace+0x0/0xf8) from [<c0011908>] (show_stack+0x10/0x14)
[<c0011908>] (show_stack+0x10/0x14) from [<c035da34>] (dump_stack+0x6c/0xac)
[<c035da34>] (dump_stack+0x6c/0xac) from [<c01b581c>] (do_raw_spin_lock+0x100/0x17c)
[<c01b581c>] (do_raw_spin_lock+0x100/0x17c) from [<c03628a0>] (_raw_spin_lock_irqsave+0x20/0x28)
[<c03628a0>] (_raw_spin_lock_irqsave+0x20/0x28) from [<c0203224>] (uart_start+0x18/0x34)
[<c0203224>] (uart_start+0x18/0x34) from [<c01ef890>] (__receive_buf+0x4b4/0x738)
[<c01ef890>] (__receive_buf+0x4b4/0x738) from [<c01efb44>] (n_tty_receive_buf2+0x30/0x98)
[<c01efb44>] (n_tty_receive_buf2+0x30/0x98) from [<c01f2ba8>] (flush_to_ldisc+0xec/0x138)
[<c01f2ba8>] (flush_to_ldisc+0xec/0x138) from [<c0031af0>] (process_one_work+0xfc/0x348)
[<c0031af0>] (process_one_work+0xfc/0x348) from [<c0032138>] (worker_thread+0x138/0x37c)
[<c0032138>] (worker_thread+0x138/0x37c) from [<c0037a7c>] (kthread+0xa4/0xb0)
[<c0037a7c>] (kthread+0xa4/0xb0) from [<c000e5f8>] (ret_from_fork+0x14/0x3c)
-----
Release the port lock before calling tty_flip_buffer_push() and reacquire it
after the call.
Similar stuff was already done for few other drivers in the past, like:
commit 2389b27216
Author: Thomas Gleixner <tglx@linutronix.de>
Date: Tue May 29 21:53:50 2007 +0100
[ARM] 4417/1: Serial: Fix AMBA drivers locking
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current driver triggers a lockdep warning for if tty_flip_buffer_push() is
called with uart_port->lock locked. This never shows up on UP kernels and comes
up only on SMP kernels.
Crash looks like this (produced with samsung.c driver):
-----
[<c0014d58>] (unwind_backtrace+0x0/0xf8) from [<c0011908>] (show_stack+0x10/0x14)
[<c0011908>] (show_stack+0x10/0x14) from [<c035da34>] (dump_stack+0x6c/0xac)
[<c035da34>] (dump_stack+0x6c/0xac) from [<c01b59ac>] (do_raw_spin_unlock+0xc4/0xd8)
[<c01b59ac>] (do_raw_spin_unlock+0xc4/0xd8) from [<c03627e4>] (_raw_spin_unlock_irqrestore+0xc/0)
[<c03627e4>] (_raw_spin_unlock_irqrestore+0xc/0x38) from [<c020a1a8>] (s3c24xx_serial_rx_chars+0)
[<c020a1a8>] (s3c24xx_serial_rx_chars+0x12c/0x260) from [<c020aae8>] (s3c64xx_serial_handle_irq+)
[<c020aae8>] (s3c64xx_serial_handle_irq+0x48/0x60) from [<c006aaa0>] (handle_irq_event_percpu+0x)
[<c006aaa0>] (handle_irq_event_percpu+0x50/0x194) from [<c006ac20>] (handle_irq_event+0x3c/0x5c)
[<c006ac20>] (handle_irq_event+0x3c/0x5c) from [<c006d864>] (handle_fasteoi_irq+0x80/0x13c)
[<c006d864>] (handle_fasteoi_irq+0x80/0x13c) from [<c006a4a4>] (generic_handle_irq+0x20/0x30)
[<c006a4a4>] (generic_handle_irq+0x20/0x30) from [<c000f454>] (handle_IRQ+0x38/0x94)
[<c000f454>] (handle_IRQ+0x38/0x94) from [<c0008538>] (gic_handle_irq+0x34/0x68)
[<c0008538>] (gic_handle_irq+0x34/0x68) from [<c00123c0>] (__irq_svc+0x40/0x70)
Exception stack(0xc04cdf70 to 0xc04cdfb8)
df60: 00000000 00000000 0000166e 00000000
df80: c04cc000 c050278f c050278f 00000001 c04d444c 410fc0f4 c03649b0 00000000
dfa0: 00000001 c04cdfb8 c000f758 c000f75c 60070013 ffffffff
[<c00123c0>] (__irq_svc+0x40/0x70) from [<c000f75c>] (arch_cpu_idle+0x28/0x30)
[<c000f75c>] (arch_cpu_idle+0x28/0x30) from [<c0054888>] (cpu_startup_entry+0x5c/0x148)
[<c0054888>] (cpu_startup_entry+0x5c/0x148) from [<c0497aa4>] (start_kernel+0x334/0x38c)
BUG: spinlock lockup suspected on CPU#0, kworker/0:1/360
lock: s3c24xx_serial_ports+0x1d8/0x370, .magic: dead4ead, .owner: <none>/-1, .owner_cpu: -1
CPU: 0 PID: 360 Comm: kworker/0:1 Not tainted 3.11.0-rc6-next-20130819-00003-g75485f1 #2
Workqueue: events flush_to_ldisc
[<c0014d58>] (unwind_backtrace+0x0/0xf8) from [<c0011908>] (show_stack+0x10/0x14)
[<c0011908>] (show_stack+0x10/0x14) from [<c035da34>] (dump_stack+0x6c/0xac)
[<c035da34>] (dump_stack+0x6c/0xac) from [<c01b581c>] (do_raw_spin_lock+0x100/0x17c)
[<c01b581c>] (do_raw_spin_lock+0x100/0x17c) from [<c03628a0>] (_raw_spin_lock_irqsave+0x20/0x28)
[<c03628a0>] (_raw_spin_lock_irqsave+0x20/0x28) from [<c0203224>] (uart_start+0x18/0x34)
[<c0203224>] (uart_start+0x18/0x34) from [<c01ef890>] (__receive_buf+0x4b4/0x738)
[<c01ef890>] (__receive_buf+0x4b4/0x738) from [<c01efb44>] (n_tty_receive_buf2+0x30/0x98)
[<c01efb44>] (n_tty_receive_buf2+0x30/0x98) from [<c01f2ba8>] (flush_to_ldisc+0xec/0x138)
[<c01f2ba8>] (flush_to_ldisc+0xec/0x138) from [<c0031af0>] (process_one_work+0xfc/0x348)
[<c0031af0>] (process_one_work+0xfc/0x348) from [<c0032138>] (worker_thread+0x138/0x37c)
[<c0032138>] (worker_thread+0x138/0x37c) from [<c0037a7c>] (kthread+0xa4/0xb0)
[<c0037a7c>] (kthread+0xa4/0xb0) from [<c000e5f8>] (ret_from_fork+0x14/0x3c)
-----
Release the port lock before calling tty_flip_buffer_push() and reacquire it
after the call.
Similar stuff was already done for few other drivers in the past, like:
commit 2389b27216
Author: Thomas Gleixner <tglx@linutronix.de>
Date: Tue May 29 21:53:50 2007 +0100
[ARM] 4417/1: Serial: Fix AMBA drivers locking
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current driver triggers a lockdep warning for if tty_flip_buffer_push() is
called with uart_port->lock locked. This never shows up on UP kernels and comes
up only on SMP kernels.
Crash looks like this (produced with samsung.c driver):
-----
[<c0014d58>] (unwind_backtrace+0x0/0xf8) from [<c0011908>] (show_stack+0x10/0x14)
[<c0011908>] (show_stack+0x10/0x14) from [<c035da34>] (dump_stack+0x6c/0xac)
[<c035da34>] (dump_stack+0x6c/0xac) from [<c01b59ac>] (do_raw_spin_unlock+0xc4/0xd8)
[<c01b59ac>] (do_raw_spin_unlock+0xc4/0xd8) from [<c03627e4>] (_raw_spin_unlock_irqrestore+0xc/0)
[<c03627e4>] (_raw_spin_unlock_irqrestore+0xc/0x38) from [<c020a1a8>] (s3c24xx_serial_rx_chars+0)
[<c020a1a8>] (s3c24xx_serial_rx_chars+0x12c/0x260) from [<c020aae8>] (s3c64xx_serial_handle_irq+)
[<c020aae8>] (s3c64xx_serial_handle_irq+0x48/0x60) from [<c006aaa0>] (handle_irq_event_percpu+0x)
[<c006aaa0>] (handle_irq_event_percpu+0x50/0x194) from [<c006ac20>] (handle_irq_event+0x3c/0x5c)
[<c006ac20>] (handle_irq_event+0x3c/0x5c) from [<c006d864>] (handle_fasteoi_irq+0x80/0x13c)
[<c006d864>] (handle_fasteoi_irq+0x80/0x13c) from [<c006a4a4>] (generic_handle_irq+0x20/0x30)
[<c006a4a4>] (generic_handle_irq+0x20/0x30) from [<c000f454>] (handle_IRQ+0x38/0x94)
[<c000f454>] (handle_IRQ+0x38/0x94) from [<c0008538>] (gic_handle_irq+0x34/0x68)
[<c0008538>] (gic_handle_irq+0x34/0x68) from [<c00123c0>] (__irq_svc+0x40/0x70)
Exception stack(0xc04cdf70 to 0xc04cdfb8)
df60: 00000000 00000000 0000166e 00000000
df80: c04cc000 c050278f c050278f 00000001 c04d444c 410fc0f4 c03649b0 00000000
dfa0: 00000001 c04cdfb8 c000f758 c000f75c 60070013 ffffffff
[<c00123c0>] (__irq_svc+0x40/0x70) from [<c000f75c>] (arch_cpu_idle+0x28/0x30)
[<c000f75c>] (arch_cpu_idle+0x28/0x30) from [<c0054888>] (cpu_startup_entry+0x5c/0x148)
[<c0054888>] (cpu_startup_entry+0x5c/0x148) from [<c0497aa4>] (start_kernel+0x334/0x38c)
BUG: spinlock lockup suspected on CPU#0, kworker/0:1/360
lock: s3c24xx_serial_ports+0x1d8/0x370, .magic: dead4ead, .owner: <none>/-1, .owner_cpu: -1
CPU: 0 PID: 360 Comm: kworker/0:1 Not tainted 3.11.0-rc6-next-20130819-00003-g75485f1 #2
Workqueue: events flush_to_ldisc
[<c0014d58>] (unwind_backtrace+0x0/0xf8) from [<c0011908>] (show_stack+0x10/0x14)
[<c0011908>] (show_stack+0x10/0x14) from [<c035da34>] (dump_stack+0x6c/0xac)
[<c035da34>] (dump_stack+0x6c/0xac) from [<c01b581c>] (do_raw_spin_lock+0x100/0x17c)
[<c01b581c>] (do_raw_spin_lock+0x100/0x17c) from [<c03628a0>] (_raw_spin_lock_irqsave+0x20/0x28)
[<c03628a0>] (_raw_spin_lock_irqsave+0x20/0x28) from [<c0203224>] (uart_start+0x18/0x34)
[<c0203224>] (uart_start+0x18/0x34) from [<c01ef890>] (__receive_buf+0x4b4/0x738)
[<c01ef890>] (__receive_buf+0x4b4/0x738) from [<c01efb44>] (n_tty_receive_buf2+0x30/0x98)
[<c01efb44>] (n_tty_receive_buf2+0x30/0x98) from [<c01f2ba8>] (flush_to_ldisc+0xec/0x138)
[<c01f2ba8>] (flush_to_ldisc+0xec/0x138) from [<c0031af0>] (process_one_work+0xfc/0x348)
[<c0031af0>] (process_one_work+0xfc/0x348) from [<c0032138>] (worker_thread+0x138/0x37c)
[<c0032138>] (worker_thread+0x138/0x37c) from [<c0037a7c>] (kthread+0xa4/0xb0)
[<c0037a7c>] (kthread+0xa4/0xb0) from [<c000e5f8>] (ret_from_fork+0x14/0x3c)
-----
Release the port lock before calling tty_flip_buffer_push() and reacquire it
after the call.
Similar stuff was already done for few other drivers in the past, like:
commit 2389b27216
Author: Thomas Gleixner <tglx@linutronix.de>
Date: Tue May 29 21:53:50 2007 +0100
[ARM] 4417/1: Serial: Fix AMBA drivers locking
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial_lpc32xx_interrupt() calls __serial_lpc32xx_rx() first and then
tty_flip_buffer_push() immediately after that. But last statement of
__serial_lpc32xx_rx() already called tty_flip_buffer_push()..
So, probably its not required to be called twice. Lets remove one of them.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current driver triggers a lockdep warning for if tty_flip_buffer_push() is
called with uart_port->lock locked. This never shows up on UP kernels and comes
up only on SMP kernels.
Crash looks like this (produced with samsung.c driver):
-----
[<c0014d58>] (unwind_backtrace+0x0/0xf8) from [<c0011908>] (show_stack+0x10/0x14)
[<c0011908>] (show_stack+0x10/0x14) from [<c035da34>] (dump_stack+0x6c/0xac)
[<c035da34>] (dump_stack+0x6c/0xac) from [<c01b59ac>] (do_raw_spin_unlock+0xc4/0xd8)
[<c01b59ac>] (do_raw_spin_unlock+0xc4/0xd8) from [<c03627e4>] (_raw_spin_unlock_irqrestore+0xc/0)
[<c03627e4>] (_raw_spin_unlock_irqrestore+0xc/0x38) from [<c020a1a8>] (s3c24xx_serial_rx_chars+0)
[<c020a1a8>] (s3c24xx_serial_rx_chars+0x12c/0x260) from [<c020aae8>] (s3c64xx_serial_handle_irq+)
[<c020aae8>] (s3c64xx_serial_handle_irq+0x48/0x60) from [<c006aaa0>] (handle_irq_event_percpu+0x)
[<c006aaa0>] (handle_irq_event_percpu+0x50/0x194) from [<c006ac20>] (handle_irq_event+0x3c/0x5c)
[<c006ac20>] (handle_irq_event+0x3c/0x5c) from [<c006d864>] (handle_fasteoi_irq+0x80/0x13c)
[<c006d864>] (handle_fasteoi_irq+0x80/0x13c) from [<c006a4a4>] (generic_handle_irq+0x20/0x30)
[<c006a4a4>] (generic_handle_irq+0x20/0x30) from [<c000f454>] (handle_IRQ+0x38/0x94)
[<c000f454>] (handle_IRQ+0x38/0x94) from [<c0008538>] (gic_handle_irq+0x34/0x68)
[<c0008538>] (gic_handle_irq+0x34/0x68) from [<c00123c0>] (__irq_svc+0x40/0x70)
Exception stack(0xc04cdf70 to 0xc04cdfb8)
df60: 00000000 00000000 0000166e 00000000
df80: c04cc000 c050278f c050278f 00000001 c04d444c 410fc0f4 c03649b0 00000000
dfa0: 00000001 c04cdfb8 c000f758 c000f75c 60070013 ffffffff
[<c00123c0>] (__irq_svc+0x40/0x70) from [<c000f75c>] (arch_cpu_idle+0x28/0x30)
[<c000f75c>] (arch_cpu_idle+0x28/0x30) from [<c0054888>] (cpu_startup_entry+0x5c/0x148)
[<c0054888>] (cpu_startup_entry+0x5c/0x148) from [<c0497aa4>] (start_kernel+0x334/0x38c)
BUG: spinlock lockup suspected on CPU#0, kworker/0:1/360
lock: s3c24xx_serial_ports+0x1d8/0x370, .magic: dead4ead, .owner: <none>/-1, .owner_cpu: -1
CPU: 0 PID: 360 Comm: kworker/0:1 Not tainted 3.11.0-rc6-next-20130819-00003-g75485f1 #2
Workqueue: events flush_to_ldisc
[<c0014d58>] (unwind_backtrace+0x0/0xf8) from [<c0011908>] (show_stack+0x10/0x14)
[<c0011908>] (show_stack+0x10/0x14) from [<c035da34>] (dump_stack+0x6c/0xac)
[<c035da34>] (dump_stack+0x6c/0xac) from [<c01b581c>] (do_raw_spin_lock+0x100/0x17c)
[<c01b581c>] (do_raw_spin_lock+0x100/0x17c) from [<c03628a0>] (_raw_spin_lock_irqsave+0x20/0x28)
[<c03628a0>] (_raw_spin_lock_irqsave+0x20/0x28) from [<c0203224>] (uart_start+0x18/0x34)
[<c0203224>] (uart_start+0x18/0x34) from [<c01ef890>] (__receive_buf+0x4b4/0x738)
[<c01ef890>] (__receive_buf+0x4b4/0x738) from [<c01efb44>] (n_tty_receive_buf2+0x30/0x98)
[<c01efb44>] (n_tty_receive_buf2+0x30/0x98) from [<c01f2ba8>] (flush_to_ldisc+0xec/0x138)
[<c01f2ba8>] (flush_to_ldisc+0xec/0x138) from [<c0031af0>] (process_one_work+0xfc/0x348)
[<c0031af0>] (process_one_work+0xfc/0x348) from [<c0032138>] (worker_thread+0x138/0x37c)
[<c0032138>] (worker_thread+0x138/0x37c) from [<c0037a7c>] (kthread+0xa4/0xb0)
[<c0037a7c>] (kthread+0xa4/0xb0) from [<c000e5f8>] (ret_from_fork+0x14/0x3c)
-----
Release the port lock before calling tty_flip_buffer_push() and reacquire it
after the call.
Similar stuff was already done for few other drivers in the past, like:
commit 2389b27216
Author: Thomas Gleixner <tglx@linutronix.de>
Date: Tue May 29 21:53:50 2007 +0100
[ARM] 4417/1: Serial: Fix AMBA drivers locking
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current driver triggers a lockdep warning for if tty_flip_buffer_push() is
called with uart_port->lock locked. This never shows up on UP kernels and comes
up only on SMP kernels.
Crash looks like this (produced with samsung.c driver):
-----
[<c0014d58>] (unwind_backtrace+0x0/0xf8) from [<c0011908>] (show_stack+0x10/0x14)
[<c0011908>] (show_stack+0x10/0x14) from [<c035da34>] (dump_stack+0x6c/0xac)
[<c035da34>] (dump_stack+0x6c/0xac) from [<c01b59ac>] (do_raw_spin_unlock+0xc4/0xd8)
[<c01b59ac>] (do_raw_spin_unlock+0xc4/0xd8) from [<c03627e4>] (_raw_spin_unlock_irqrestore+0xc/0)
[<c03627e4>] (_raw_spin_unlock_irqrestore+0xc/0x38) from [<c020a1a8>] (s3c24xx_serial_rx_chars+0)
[<c020a1a8>] (s3c24xx_serial_rx_chars+0x12c/0x260) from [<c020aae8>] (s3c64xx_serial_handle_irq+)
[<c020aae8>] (s3c64xx_serial_handle_irq+0x48/0x60) from [<c006aaa0>] (handle_irq_event_percpu+0x)
[<c006aaa0>] (handle_irq_event_percpu+0x50/0x194) from [<c006ac20>] (handle_irq_event+0x3c/0x5c)
[<c006ac20>] (handle_irq_event+0x3c/0x5c) from [<c006d864>] (handle_fasteoi_irq+0x80/0x13c)
[<c006d864>] (handle_fasteoi_irq+0x80/0x13c) from [<c006a4a4>] (generic_handle_irq+0x20/0x30)
[<c006a4a4>] (generic_handle_irq+0x20/0x30) from [<c000f454>] (handle_IRQ+0x38/0x94)
[<c000f454>] (handle_IRQ+0x38/0x94) from [<c0008538>] (gic_handle_irq+0x34/0x68)
[<c0008538>] (gic_handle_irq+0x34/0x68) from [<c00123c0>] (__irq_svc+0x40/0x70)
Exception stack(0xc04cdf70 to 0xc04cdfb8)
df60: 00000000 00000000 0000166e 00000000
df80: c04cc000 c050278f c050278f 00000001 c04d444c 410fc0f4 c03649b0 00000000
dfa0: 00000001 c04cdfb8 c000f758 c000f75c 60070013 ffffffff
[<c00123c0>] (__irq_svc+0x40/0x70) from [<c000f75c>] (arch_cpu_idle+0x28/0x30)
[<c000f75c>] (arch_cpu_idle+0x28/0x30) from [<c0054888>] (cpu_startup_entry+0x5c/0x148)
[<c0054888>] (cpu_startup_entry+0x5c/0x148) from [<c0497aa4>] (start_kernel+0x334/0x38c)
BUG: spinlock lockup suspected on CPU#0, kworker/0:1/360
lock: s3c24xx_serial_ports+0x1d8/0x370, .magic: dead4ead, .owner: <none>/-1, .owner_cpu: -1
CPU: 0 PID: 360 Comm: kworker/0:1 Not tainted 3.11.0-rc6-next-20130819-00003-g75485f1 #2
Workqueue: events flush_to_ldisc
[<c0014d58>] (unwind_backtrace+0x0/0xf8) from [<c0011908>] (show_stack+0x10/0x14)
[<c0011908>] (show_stack+0x10/0x14) from [<c035da34>] (dump_stack+0x6c/0xac)
[<c035da34>] (dump_stack+0x6c/0xac) from [<c01b581c>] (do_raw_spin_lock+0x100/0x17c)
[<c01b581c>] (do_raw_spin_lock+0x100/0x17c) from [<c03628a0>] (_raw_spin_lock_irqsave+0x20/0x28)
[<c03628a0>] (_raw_spin_lock_irqsave+0x20/0x28) from [<c0203224>] (uart_start+0x18/0x34)
[<c0203224>] (uart_start+0x18/0x34) from [<c01ef890>] (__receive_buf+0x4b4/0x738)
[<c01ef890>] (__receive_buf+0x4b4/0x738) from [<c01efb44>] (n_tty_receive_buf2+0x30/0x98)
[<c01efb44>] (n_tty_receive_buf2+0x30/0x98) from [<c01f2ba8>] (flush_to_ldisc+0xec/0x138)
[<c01f2ba8>] (flush_to_ldisc+0xec/0x138) from [<c0031af0>] (process_one_work+0xfc/0x348)
[<c0031af0>] (process_one_work+0xfc/0x348) from [<c0032138>] (worker_thread+0x138/0x37c)
[<c0032138>] (worker_thread+0x138/0x37c) from [<c0037a7c>] (kthread+0xa4/0xb0)
[<c0037a7c>] (kthread+0xa4/0xb0) from [<c000e5f8>] (ret_from_fork+0x14/0x3c)
-----
Release the port lock before calling tty_flip_buffer_push() and reacquire it
after the call.
Similar stuff was already done for few other drivers in the past, like:
commit 2389b27216
Author: Thomas Gleixner <tglx@linutronix.de>
Date: Tue May 29 21:53:50 2007 +0100
[ARM] 4417/1: Serial: Fix AMBA drivers locking
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current driver triggers a lockdep warning for if tty_flip_buffer_push() is
called with uart_port->lock locked. This never shows up on UP kernels and comes
up only on SMP kernels.
Crash looks like this (produced with samsung.c driver):
-----
[<c0014d58>] (unwind_backtrace+0x0/0xf8) from [<c0011908>] (show_stack+0x10/0x14)
[<c0011908>] (show_stack+0x10/0x14) from [<c035da34>] (dump_stack+0x6c/0xac)
[<c035da34>] (dump_stack+0x6c/0xac) from [<c01b59ac>] (do_raw_spin_unlock+0xc4/0xd8)
[<c01b59ac>] (do_raw_spin_unlock+0xc4/0xd8) from [<c03627e4>] (_raw_spin_unlock_irqrestore+0xc/0)
[<c03627e4>] (_raw_spin_unlock_irqrestore+0xc/0x38) from [<c020a1a8>] (s3c24xx_serial_rx_chars+0)
[<c020a1a8>] (s3c24xx_serial_rx_chars+0x12c/0x260) from [<c020aae8>] (s3c64xx_serial_handle_irq+)
[<c020aae8>] (s3c64xx_serial_handle_irq+0x48/0x60) from [<c006aaa0>] (handle_irq_event_percpu+0x)
[<c006aaa0>] (handle_irq_event_percpu+0x50/0x194) from [<c006ac20>] (handle_irq_event+0x3c/0x5c)
[<c006ac20>] (handle_irq_event+0x3c/0x5c) from [<c006d864>] (handle_fasteoi_irq+0x80/0x13c)
[<c006d864>] (handle_fasteoi_irq+0x80/0x13c) from [<c006a4a4>] (generic_handle_irq+0x20/0x30)
[<c006a4a4>] (generic_handle_irq+0x20/0x30) from [<c000f454>] (handle_IRQ+0x38/0x94)
[<c000f454>] (handle_IRQ+0x38/0x94) from [<c0008538>] (gic_handle_irq+0x34/0x68)
[<c0008538>] (gic_handle_irq+0x34/0x68) from [<c00123c0>] (__irq_svc+0x40/0x70)
Exception stack(0xc04cdf70 to 0xc04cdfb8)
df60: 00000000 00000000 0000166e 00000000
df80: c04cc000 c050278f c050278f 00000001 c04d444c 410fc0f4 c03649b0 00000000
dfa0: 00000001 c04cdfb8 c000f758 c000f75c 60070013 ffffffff
[<c00123c0>] (__irq_svc+0x40/0x70) from [<c000f75c>] (arch_cpu_idle+0x28/0x30)
[<c000f75c>] (arch_cpu_idle+0x28/0x30) from [<c0054888>] (cpu_startup_entry+0x5c/0x148)
[<c0054888>] (cpu_startup_entry+0x5c/0x148) from [<c0497aa4>] (start_kernel+0x334/0x38c)
BUG: spinlock lockup suspected on CPU#0, kworker/0:1/360
lock: s3c24xx_serial_ports+0x1d8/0x370, .magic: dead4ead, .owner: <none>/-1, .owner_cpu: -1
CPU: 0 PID: 360 Comm: kworker/0:1 Not tainted 3.11.0-rc6-next-20130819-00003-g75485f1 #2
Workqueue: events flush_to_ldisc
[<c0014d58>] (unwind_backtrace+0x0/0xf8) from [<c0011908>] (show_stack+0x10/0x14)
[<c0011908>] (show_stack+0x10/0x14) from [<c035da34>] (dump_stack+0x6c/0xac)
[<c035da34>] (dump_stack+0x6c/0xac) from [<c01b581c>] (do_raw_spin_lock+0x100/0x17c)
[<c01b581c>] (do_raw_spin_lock+0x100/0x17c) from [<c03628a0>] (_raw_spin_lock_irqsave+0x20/0x28)
[<c03628a0>] (_raw_spin_lock_irqsave+0x20/0x28) from [<c0203224>] (uart_start+0x18/0x34)
[<c0203224>] (uart_start+0x18/0x34) from [<c01ef890>] (__receive_buf+0x4b4/0x738)
[<c01ef890>] (__receive_buf+0x4b4/0x738) from [<c01efb44>] (n_tty_receive_buf2+0x30/0x98)
[<c01efb44>] (n_tty_receive_buf2+0x30/0x98) from [<c01f2ba8>] (flush_to_ldisc+0xec/0x138)
[<c01f2ba8>] (flush_to_ldisc+0xec/0x138) from [<c0031af0>] (process_one_work+0xfc/0x348)
[<c0031af0>] (process_one_work+0xfc/0x348) from [<c0032138>] (worker_thread+0x138/0x37c)
[<c0032138>] (worker_thread+0x138/0x37c) from [<c0037a7c>] (kthread+0xa4/0xb0)
[<c0037a7c>] (kthread+0xa4/0xb0) from [<c000e5f8>] (ret_from_fork+0x14/0x3c)
-----
Release the port lock before calling tty_flip_buffer_push() and reacquire it
after the call.
Similar stuff was already done for few other drivers in the past, like:
commit 2389b27216
Author: Thomas Gleixner <tglx@linutronix.de>
Date: Tue May 29 21:53:50 2007 +0100
[ARM] 4417/1: Serial: Fix AMBA drivers locking
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current driver triggers a lockdep warning for if tty_flip_buffer_push() is
called with uart_port->lock locked. This never shows up on UP kernels and comes
up only on SMP kernels.
Crash looks like this (produced with samsung.c driver):
-----
[<c0014d58>] (unwind_backtrace+0x0/0xf8) from [<c0011908>] (show_stack+0x10/0x14)
[<c0011908>] (show_stack+0x10/0x14) from [<c035da34>] (dump_stack+0x6c/0xac)
[<c035da34>] (dump_stack+0x6c/0xac) from [<c01b59ac>] (do_raw_spin_unlock+0xc4/0xd8)
[<c01b59ac>] (do_raw_spin_unlock+0xc4/0xd8) from [<c03627e4>] (_raw_spin_unlock_irqrestore+0xc/0)
[<c03627e4>] (_raw_spin_unlock_irqrestore+0xc/0x38) from [<c020a1a8>] (s3c24xx_serial_rx_chars+0)
[<c020a1a8>] (s3c24xx_serial_rx_chars+0x12c/0x260) from [<c020aae8>] (s3c64xx_serial_handle_irq+)
[<c020aae8>] (s3c64xx_serial_handle_irq+0x48/0x60) from [<c006aaa0>] (handle_irq_event_percpu+0x)
[<c006aaa0>] (handle_irq_event_percpu+0x50/0x194) from [<c006ac20>] (handle_irq_event+0x3c/0x5c)
[<c006ac20>] (handle_irq_event+0x3c/0x5c) from [<c006d864>] (handle_fasteoi_irq+0x80/0x13c)
[<c006d864>] (handle_fasteoi_irq+0x80/0x13c) from [<c006a4a4>] (generic_handle_irq+0x20/0x30)
[<c006a4a4>] (generic_handle_irq+0x20/0x30) from [<c000f454>] (handle_IRQ+0x38/0x94)
[<c000f454>] (handle_IRQ+0x38/0x94) from [<c0008538>] (gic_handle_irq+0x34/0x68)
[<c0008538>] (gic_handle_irq+0x34/0x68) from [<c00123c0>] (__irq_svc+0x40/0x70)
Exception stack(0xc04cdf70 to 0xc04cdfb8)
df60: 00000000 00000000 0000166e 00000000
df80: c04cc000 c050278f c050278f 00000001 c04d444c 410fc0f4 c03649b0 00000000
dfa0: 00000001 c04cdfb8 c000f758 c000f75c 60070013 ffffffff
[<c00123c0>] (__irq_svc+0x40/0x70) from [<c000f75c>] (arch_cpu_idle+0x28/0x30)
[<c000f75c>] (arch_cpu_idle+0x28/0x30) from [<c0054888>] (cpu_startup_entry+0x5c/0x148)
[<c0054888>] (cpu_startup_entry+0x5c/0x148) from [<c0497aa4>] (start_kernel+0x334/0x38c)
BUG: spinlock lockup suspected on CPU#0, kworker/0:1/360
lock: s3c24xx_serial_ports+0x1d8/0x370, .magic: dead4ead, .owner: <none>/-1, .owner_cpu: -1
CPU: 0 PID: 360 Comm: kworker/0:1 Not tainted 3.11.0-rc6-next-20130819-00003-g75485f1 #2
Workqueue: events flush_to_ldisc
[<c0014d58>] (unwind_backtrace+0x0/0xf8) from [<c0011908>] (show_stack+0x10/0x14)
[<c0011908>] (show_stack+0x10/0x14) from [<c035da34>] (dump_stack+0x6c/0xac)
[<c035da34>] (dump_stack+0x6c/0xac) from [<c01b581c>] (do_raw_spin_lock+0x100/0x17c)
[<c01b581c>] (do_raw_spin_lock+0x100/0x17c) from [<c03628a0>] (_raw_spin_lock_irqsave+0x20/0x28)
[<c03628a0>] (_raw_spin_lock_irqsave+0x20/0x28) from [<c0203224>] (uart_start+0x18/0x34)
[<c0203224>] (uart_start+0x18/0x34) from [<c01ef890>] (__receive_buf+0x4b4/0x738)
[<c01ef890>] (__receive_buf+0x4b4/0x738) from [<c01efb44>] (n_tty_receive_buf2+0x30/0x98)
[<c01efb44>] (n_tty_receive_buf2+0x30/0x98) from [<c01f2ba8>] (flush_to_ldisc+0xec/0x138)
[<c01f2ba8>] (flush_to_ldisc+0xec/0x138) from [<c0031af0>] (process_one_work+0xfc/0x348)
[<c0031af0>] (process_one_work+0xfc/0x348) from [<c0032138>] (worker_thread+0x138/0x37c)
[<c0032138>] (worker_thread+0x138/0x37c) from [<c0037a7c>] (kthread+0xa4/0xb0)
[<c0037a7c>] (kthread+0xa4/0xb0) from [<c000e5f8>] (ret_from_fork+0x14/0x3c)
-----
Release the port lock before calling tty_flip_buffer_push() and reacquire it
after the call.
Similar stuff was already done for few other drivers in the past, like:
commit 2389b27216
Author: Thomas Gleixner <tglx@linutronix.de>
Date: Tue May 29 21:53:50 2007 +0100
[ARM] 4417/1: Serial: Fix AMBA drivers locking
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current driver triggers a lockdep warning for if tty_flip_buffer_push() is
called with uart_port->lock locked. This never shows up on UP kernels and comes
up only on SMP kernels.
Crash looks like this (produced with samsung.c driver):
-----
[<c0014d58>] (unwind_backtrace+0x0/0xf8) from [<c0011908>] (show_stack+0x10/0x14)
[<c0011908>] (show_stack+0x10/0x14) from [<c035da34>] (dump_stack+0x6c/0xac)
[<c035da34>] (dump_stack+0x6c/0xac) from [<c01b59ac>] (do_raw_spin_unlock+0xc4/0xd8)
[<c01b59ac>] (do_raw_spin_unlock+0xc4/0xd8) from [<c03627e4>] (_raw_spin_unlock_irqrestore+0xc/0)
[<c03627e4>] (_raw_spin_unlock_irqrestore+0xc/0x38) from [<c020a1a8>] (s3c24xx_serial_rx_chars+0)
[<c020a1a8>] (s3c24xx_serial_rx_chars+0x12c/0x260) from [<c020aae8>] (s3c64xx_serial_handle_irq+)
[<c020aae8>] (s3c64xx_serial_handle_irq+0x48/0x60) from [<c006aaa0>] (handle_irq_event_percpu+0x)
[<c006aaa0>] (handle_irq_event_percpu+0x50/0x194) from [<c006ac20>] (handle_irq_event+0x3c/0x5c)
[<c006ac20>] (handle_irq_event+0x3c/0x5c) from [<c006d864>] (handle_fasteoi_irq+0x80/0x13c)
[<c006d864>] (handle_fasteoi_irq+0x80/0x13c) from [<c006a4a4>] (generic_handle_irq+0x20/0x30)
[<c006a4a4>] (generic_handle_irq+0x20/0x30) from [<c000f454>] (handle_IRQ+0x38/0x94)
[<c000f454>] (handle_IRQ+0x38/0x94) from [<c0008538>] (gic_handle_irq+0x34/0x68)
[<c0008538>] (gic_handle_irq+0x34/0x68) from [<c00123c0>] (__irq_svc+0x40/0x70)
Exception stack(0xc04cdf70 to 0xc04cdfb8)
df60: 00000000 00000000 0000166e 00000000
df80: c04cc000 c050278f c050278f 00000001 c04d444c 410fc0f4 c03649b0 00000000
dfa0: 00000001 c04cdfb8 c000f758 c000f75c 60070013 ffffffff
[<c00123c0>] (__irq_svc+0x40/0x70) from [<c000f75c>] (arch_cpu_idle+0x28/0x30)
[<c000f75c>] (arch_cpu_idle+0x28/0x30) from [<c0054888>] (cpu_startup_entry+0x5c/0x148)
[<c0054888>] (cpu_startup_entry+0x5c/0x148) from [<c0497aa4>] (start_kernel+0x334/0x38c)
BUG: spinlock lockup suspected on CPU#0, kworker/0:1/360
lock: s3c24xx_serial_ports+0x1d8/0x370, .magic: dead4ead, .owner: <none>/-1, .owner_cpu: -1
CPU: 0 PID: 360 Comm: kworker/0:1 Not tainted 3.11.0-rc6-next-20130819-00003-g75485f1 #2
Workqueue: events flush_to_ldisc
[<c0014d58>] (unwind_backtrace+0x0/0xf8) from [<c0011908>] (show_stack+0x10/0x14)
[<c0011908>] (show_stack+0x10/0x14) from [<c035da34>] (dump_stack+0x6c/0xac)
[<c035da34>] (dump_stack+0x6c/0xac) from [<c01b581c>] (do_raw_spin_lock+0x100/0x17c)
[<c01b581c>] (do_raw_spin_lock+0x100/0x17c) from [<c03628a0>] (_raw_spin_lock_irqsave+0x20/0x28)
[<c03628a0>] (_raw_spin_lock_irqsave+0x20/0x28) from [<c0203224>] (uart_start+0x18/0x34)
[<c0203224>] (uart_start+0x18/0x34) from [<c01ef890>] (__receive_buf+0x4b4/0x738)
[<c01ef890>] (__receive_buf+0x4b4/0x738) from [<c01efb44>] (n_tty_receive_buf2+0x30/0x98)
[<c01efb44>] (n_tty_receive_buf2+0x30/0x98) from [<c01f2ba8>] (flush_to_ldisc+0xec/0x138)
[<c01f2ba8>] (flush_to_ldisc+0xec/0x138) from [<c0031af0>] (process_one_work+0xfc/0x348)
[<c0031af0>] (process_one_work+0xfc/0x348) from [<c0032138>] (worker_thread+0x138/0x37c)
[<c0032138>] (worker_thread+0x138/0x37c) from [<c0037a7c>] (kthread+0xa4/0xb0)
[<c0037a7c>] (kthread+0xa4/0xb0) from [<c000e5f8>] (ret_from_fork+0x14/0x3c)
-----
Release the port lock before calling tty_flip_buffer_push() and reacquire it
after the call.
Similar stuff was already done for few other drivers in the past, like:
commit 2389b27216
Author: Thomas Gleixner <tglx@linutronix.de>
Date: Tue May 29 21:53:50 2007 +0100
[ARM] 4417/1: Serial: Fix AMBA drivers locking
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current driver triggers a lockdep warning for if tty_flip_buffer_push() is
called with uart_port->lock locked. This never shows up on UP kernels and comes
up only on SMP kernels.
Crash looks like this (produced with samsung.c driver):
-----
[<c0014d58>] (unwind_backtrace+0x0/0xf8) from [<c0011908>] (show_stack+0x10/0x14)
[<c0011908>] (show_stack+0x10/0x14) from [<c035da34>] (dump_stack+0x6c/0xac)
[<c035da34>] (dump_stack+0x6c/0xac) from [<c01b59ac>] (do_raw_spin_unlock+0xc4/0xd8)
[<c01b59ac>] (do_raw_spin_unlock+0xc4/0xd8) from [<c03627e4>] (_raw_spin_unlock_irqrestore+0xc/0)
[<c03627e4>] (_raw_spin_unlock_irqrestore+0xc/0x38) from [<c020a1a8>] (s3c24xx_serial_rx_chars+0)
[<c020a1a8>] (s3c24xx_serial_rx_chars+0x12c/0x260) from [<c020aae8>] (s3c64xx_serial_handle_irq+)
[<c020aae8>] (s3c64xx_serial_handle_irq+0x48/0x60) from [<c006aaa0>] (handle_irq_event_percpu+0x)
[<c006aaa0>] (handle_irq_event_percpu+0x50/0x194) from [<c006ac20>] (handle_irq_event+0x3c/0x5c)
[<c006ac20>] (handle_irq_event+0x3c/0x5c) from [<c006d864>] (handle_fasteoi_irq+0x80/0x13c)
[<c006d864>] (handle_fasteoi_irq+0x80/0x13c) from [<c006a4a4>] (generic_handle_irq+0x20/0x30)
[<c006a4a4>] (generic_handle_irq+0x20/0x30) from [<c000f454>] (handle_IRQ+0x38/0x94)
[<c000f454>] (handle_IRQ+0x38/0x94) from [<c0008538>] (gic_handle_irq+0x34/0x68)
[<c0008538>] (gic_handle_irq+0x34/0x68) from [<c00123c0>] (__irq_svc+0x40/0x70)
Exception stack(0xc04cdf70 to 0xc04cdfb8)
df60: 00000000 00000000 0000166e 00000000
df80: c04cc000 c050278f c050278f 00000001 c04d444c 410fc0f4 c03649b0 00000000
dfa0: 00000001 c04cdfb8 c000f758 c000f75c 60070013 ffffffff
[<c00123c0>] (__irq_svc+0x40/0x70) from [<c000f75c>] (arch_cpu_idle+0x28/0x30)
[<c000f75c>] (arch_cpu_idle+0x28/0x30) from [<c0054888>] (cpu_startup_entry+0x5c/0x148)
[<c0054888>] (cpu_startup_entry+0x5c/0x148) from [<c0497aa4>] (start_kernel+0x334/0x38c)
BUG: spinlock lockup suspected on CPU#0, kworker/0:1/360
lock: s3c24xx_serial_ports+0x1d8/0x370, .magic: dead4ead, .owner: <none>/-1, .owner_cpu: -1
CPU: 0 PID: 360 Comm: kworker/0:1 Not tainted 3.11.0-rc6-next-20130819-00003-g75485f1 #2
Workqueue: events flush_to_ldisc
[<c0014d58>] (unwind_backtrace+0x0/0xf8) from [<c0011908>] (show_stack+0x10/0x14)
[<c0011908>] (show_stack+0x10/0x14) from [<c035da34>] (dump_stack+0x6c/0xac)
[<c035da34>] (dump_stack+0x6c/0xac) from [<c01b581c>] (do_raw_spin_lock+0x100/0x17c)
[<c01b581c>] (do_raw_spin_lock+0x100/0x17c) from [<c03628a0>] (_raw_spin_lock_irqsave+0x20/0x28)
[<c03628a0>] (_raw_spin_lock_irqsave+0x20/0x28) from [<c0203224>] (uart_start+0x18/0x34)
[<c0203224>] (uart_start+0x18/0x34) from [<c01ef890>] (__receive_buf+0x4b4/0x738)
[<c01ef890>] (__receive_buf+0x4b4/0x738) from [<c01efb44>] (n_tty_receive_buf2+0x30/0x98)
[<c01efb44>] (n_tty_receive_buf2+0x30/0x98) from [<c01f2ba8>] (flush_to_ldisc+0xec/0x138)
[<c01f2ba8>] (flush_to_ldisc+0xec/0x138) from [<c0031af0>] (process_one_work+0xfc/0x348)
[<c0031af0>] (process_one_work+0xfc/0x348) from [<c0032138>] (worker_thread+0x138/0x37c)
[<c0032138>] (worker_thread+0x138/0x37c) from [<c0037a7c>] (kthread+0xa4/0xb0)
[<c0037a7c>] (kthread+0xa4/0xb0) from [<c000e5f8>] (ret_from_fork+0x14/0x3c)
-----
Release the port lock before calling tty_flip_buffer_push() and reacquire it
after the call.
Similar stuff was already done for few other drivers in the past, like:
commit 2389b27216
Author: Thomas Gleixner <tglx@linutronix.de>
Date: Tue May 29 21:53:50 2007 +0100
[ARM] 4417/1: Serial: Fix AMBA drivers locking
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current driver triggers a lockdep warning for if tty_flip_buffer_push() is
called with uart_port->lock locked. This never shows up on UP kernels and comes
up only on SMP kernels.
Crash looks like this (produced with samsung.c driver):
-----
[<c0014d58>] (unwind_backtrace+0x0/0xf8) from [<c0011908>] (show_stack+0x10/0x14)
[<c0011908>] (show_stack+0x10/0x14) from [<c035da34>] (dump_stack+0x6c/0xac)
[<c035da34>] (dump_stack+0x6c/0xac) from [<c01b59ac>] (do_raw_spin_unlock+0xc4/0xd8)
[<c01b59ac>] (do_raw_spin_unlock+0xc4/0xd8) from [<c03627e4>] (_raw_spin_unlock_irqrestore+0xc/0)
[<c03627e4>] (_raw_spin_unlock_irqrestore+0xc/0x38) from [<c020a1a8>] (s3c24xx_serial_rx_chars+0)
[<c020a1a8>] (s3c24xx_serial_rx_chars+0x12c/0x260) from [<c020aae8>] (s3c64xx_serial_handle_irq+)
[<c020aae8>] (s3c64xx_serial_handle_irq+0x48/0x60) from [<c006aaa0>] (handle_irq_event_percpu+0x)
[<c006aaa0>] (handle_irq_event_percpu+0x50/0x194) from [<c006ac20>] (handle_irq_event+0x3c/0x5c)
[<c006ac20>] (handle_irq_event+0x3c/0x5c) from [<c006d864>] (handle_fasteoi_irq+0x80/0x13c)
[<c006d864>] (handle_fasteoi_irq+0x80/0x13c) from [<c006a4a4>] (generic_handle_irq+0x20/0x30)
[<c006a4a4>] (generic_handle_irq+0x20/0x30) from [<c000f454>] (handle_IRQ+0x38/0x94)
[<c000f454>] (handle_IRQ+0x38/0x94) from [<c0008538>] (gic_handle_irq+0x34/0x68)
[<c0008538>] (gic_handle_irq+0x34/0x68) from [<c00123c0>] (__irq_svc+0x40/0x70)
Exception stack(0xc04cdf70 to 0xc04cdfb8)
df60: 00000000 00000000 0000166e 00000000
df80: c04cc000 c050278f c050278f 00000001 c04d444c 410fc0f4 c03649b0 00000000
dfa0: 00000001 c04cdfb8 c000f758 c000f75c 60070013 ffffffff
[<c00123c0>] (__irq_svc+0x40/0x70) from [<c000f75c>] (arch_cpu_idle+0x28/0x30)
[<c000f75c>] (arch_cpu_idle+0x28/0x30) from [<c0054888>] (cpu_startup_entry+0x5c/0x148)
[<c0054888>] (cpu_startup_entry+0x5c/0x148) from [<c0497aa4>] (start_kernel+0x334/0x38c)
BUG: spinlock lockup suspected on CPU#0, kworker/0:1/360
lock: s3c24xx_serial_ports+0x1d8/0x370, .magic: dead4ead, .owner: <none>/-1, .owner_cpu: -1
CPU: 0 PID: 360 Comm: kworker/0:1 Not tainted 3.11.0-rc6-next-20130819-00003-g75485f1 #2
Workqueue: events flush_to_ldisc
[<c0014d58>] (unwind_backtrace+0x0/0xf8) from [<c0011908>] (show_stack+0x10/0x14)
[<c0011908>] (show_stack+0x10/0x14) from [<c035da34>] (dump_stack+0x6c/0xac)
[<c035da34>] (dump_stack+0x6c/0xac) from [<c01b581c>] (do_raw_spin_lock+0x100/0x17c)
[<c01b581c>] (do_raw_spin_lock+0x100/0x17c) from [<c03628a0>] (_raw_spin_lock_irqsave+0x20/0x28)
[<c03628a0>] (_raw_spin_lock_irqsave+0x20/0x28) from [<c0203224>] (uart_start+0x18/0x34)
[<c0203224>] (uart_start+0x18/0x34) from [<c01ef890>] (__receive_buf+0x4b4/0x738)
[<c01ef890>] (__receive_buf+0x4b4/0x738) from [<c01efb44>] (n_tty_receive_buf2+0x30/0x98)
[<c01efb44>] (n_tty_receive_buf2+0x30/0x98) from [<c01f2ba8>] (flush_to_ldisc+0xec/0x138)
[<c01f2ba8>] (flush_to_ldisc+0xec/0x138) from [<c0031af0>] (process_one_work+0xfc/0x348)
[<c0031af0>] (process_one_work+0xfc/0x348) from [<c0032138>] (worker_thread+0x138/0x37c)
[<c0032138>] (worker_thread+0x138/0x37c) from [<c0037a7c>] (kthread+0xa4/0xb0)
[<c0037a7c>] (kthread+0xa4/0xb0) from [<c000e5f8>] (ret_from_fork+0x14/0x3c)
-----
Release the port lock before calling tty_flip_buffer_push() and reacquire it
after the call.
Similar stuff was already done for few other drivers in the past, like:
commit 2389b27216
Author: Thomas Gleixner <tglx@linutronix.de>
Date: Tue May 29 21:53:50 2007 +0100
[ARM] 4417/1: Serial: Fix AMBA drivers locking
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current driver triggers a lockdep warning for if tty_flip_buffer_push() is
called with uart_port->lock locked. This never shows up on UP kernels and comes
up only on SMP kernels.
Crash looks like this (produced with samsung.c driver):
-----
[<c0014d58>] (unwind_backtrace+0x0/0xf8) from [<c0011908>] (show_stack+0x10/0x14)
[<c0011908>] (show_stack+0x10/0x14) from [<c035da34>] (dump_stack+0x6c/0xac)
[<c035da34>] (dump_stack+0x6c/0xac) from [<c01b59ac>] (do_raw_spin_unlock+0xc4/0xd8)
[<c01b59ac>] (do_raw_spin_unlock+0xc4/0xd8) from [<c03627e4>] (_raw_spin_unlock_irqrestore+0xc/0)
[<c03627e4>] (_raw_spin_unlock_irqrestore+0xc/0x38) from [<c020a1a8>] (s3c24xx_serial_rx_chars+0)
[<c020a1a8>] (s3c24xx_serial_rx_chars+0x12c/0x260) from [<c020aae8>] (s3c64xx_serial_handle_irq+)
[<c020aae8>] (s3c64xx_serial_handle_irq+0x48/0x60) from [<c006aaa0>] (handle_irq_event_percpu+0x)
[<c006aaa0>] (handle_irq_event_percpu+0x50/0x194) from [<c006ac20>] (handle_irq_event+0x3c/0x5c)
[<c006ac20>] (handle_irq_event+0x3c/0x5c) from [<c006d864>] (handle_fasteoi_irq+0x80/0x13c)
[<c006d864>] (handle_fasteoi_irq+0x80/0x13c) from [<c006a4a4>] (generic_handle_irq+0x20/0x30)
[<c006a4a4>] (generic_handle_irq+0x20/0x30) from [<c000f454>] (handle_IRQ+0x38/0x94)
[<c000f454>] (handle_IRQ+0x38/0x94) from [<c0008538>] (gic_handle_irq+0x34/0x68)
[<c0008538>] (gic_handle_irq+0x34/0x68) from [<c00123c0>] (__irq_svc+0x40/0x70)
Exception stack(0xc04cdf70 to 0xc04cdfb8)
df60: 00000000 00000000 0000166e 00000000
df80: c04cc000 c050278f c050278f 00000001 c04d444c 410fc0f4 c03649b0 00000000
dfa0: 00000001 c04cdfb8 c000f758 c000f75c 60070013 ffffffff
[<c00123c0>] (__irq_svc+0x40/0x70) from [<c000f75c>] (arch_cpu_idle+0x28/0x30)
[<c000f75c>] (arch_cpu_idle+0x28/0x30) from [<c0054888>] (cpu_startup_entry+0x5c/0x148)
[<c0054888>] (cpu_startup_entry+0x5c/0x148) from [<c0497aa4>] (start_kernel+0x334/0x38c)
BUG: spinlock lockup suspected on CPU#0, kworker/0:1/360
lock: s3c24xx_serial_ports+0x1d8/0x370, .magic: dead4ead, .owner: <none>/-1, .owner_cpu: -1
CPU: 0 PID: 360 Comm: kworker/0:1 Not tainted 3.11.0-rc6-next-20130819-00003-g75485f1 #2
Workqueue: events flush_to_ldisc
[<c0014d58>] (unwind_backtrace+0x0/0xf8) from [<c0011908>] (show_stack+0x10/0x14)
[<c0011908>] (show_stack+0x10/0x14) from [<c035da34>] (dump_stack+0x6c/0xac)
[<c035da34>] (dump_stack+0x6c/0xac) from [<c01b581c>] (do_raw_spin_lock+0x100/0x17c)
[<c01b581c>] (do_raw_spin_lock+0x100/0x17c) from [<c03628a0>] (_raw_spin_lock_irqsave+0x20/0x28)
[<c03628a0>] (_raw_spin_lock_irqsave+0x20/0x28) from [<c0203224>] (uart_start+0x18/0x34)
[<c0203224>] (uart_start+0x18/0x34) from [<c01ef890>] (__receive_buf+0x4b4/0x738)
[<c01ef890>] (__receive_buf+0x4b4/0x738) from [<c01efb44>] (n_tty_receive_buf2+0x30/0x98)
[<c01efb44>] (n_tty_receive_buf2+0x30/0x98) from [<c01f2ba8>] (flush_to_ldisc+0xec/0x138)
[<c01f2ba8>] (flush_to_ldisc+0xec/0x138) from [<c0031af0>] (process_one_work+0xfc/0x348)
[<c0031af0>] (process_one_work+0xfc/0x348) from [<c0032138>] (worker_thread+0x138/0x37c)
[<c0032138>] (worker_thread+0x138/0x37c) from [<c0037a7c>] (kthread+0xa4/0xb0)
[<c0037a7c>] (kthread+0xa4/0xb0) from [<c000e5f8>] (ret_from_fork+0x14/0x3c)
-----
Release the port lock before calling tty_flip_buffer_push() and reacquire it
after the call.
Similar stuff was already done for few other drivers in the past, like:
commit 2389b27216
Author: Thomas Gleixner <tglx@linutronix.de>
Date: Tue May 29 21:53:50 2007 +0100
[ARM] 4417/1: Serial: Fix AMBA drivers locking
Cc: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current driver triggers a lockdep warning for if tty_flip_buffer_push() is
called with uart_port->lock locked. This never shows up on UP kernels and comes
up only on SMP kernels.
Crash looks like this (produced with samsung.c driver):
-----
[<c0014d58>] (unwind_backtrace+0x0/0xf8) from [<c0011908>] (show_stack+0x10/0x14)
[<c0011908>] (show_stack+0x10/0x14) from [<c035da34>] (dump_stack+0x6c/0xac)
[<c035da34>] (dump_stack+0x6c/0xac) from [<c01b59ac>] (do_raw_spin_unlock+0xc4/0xd8)
[<c01b59ac>] (do_raw_spin_unlock+0xc4/0xd8) from [<c03627e4>] (_raw_spin_unlock_irqrestore+0xc/0)
[<c03627e4>] (_raw_spin_unlock_irqrestore+0xc/0x38) from [<c020a1a8>] (s3c24xx_serial_rx_chars+0)
[<c020a1a8>] (s3c24xx_serial_rx_chars+0x12c/0x260) from [<c020aae8>] (s3c64xx_serial_handle_irq+)
[<c020aae8>] (s3c64xx_serial_handle_irq+0x48/0x60) from [<c006aaa0>] (handle_irq_event_percpu+0x)
[<c006aaa0>] (handle_irq_event_percpu+0x50/0x194) from [<c006ac20>] (handle_irq_event+0x3c/0x5c)
[<c006ac20>] (handle_irq_event+0x3c/0x5c) from [<c006d864>] (handle_fasteoi_irq+0x80/0x13c)
[<c006d864>] (handle_fasteoi_irq+0x80/0x13c) from [<c006a4a4>] (generic_handle_irq+0x20/0x30)
[<c006a4a4>] (generic_handle_irq+0x20/0x30) from [<c000f454>] (handle_IRQ+0x38/0x94)
[<c000f454>] (handle_IRQ+0x38/0x94) from [<c0008538>] (gic_handle_irq+0x34/0x68)
[<c0008538>] (gic_handle_irq+0x34/0x68) from [<c00123c0>] (__irq_svc+0x40/0x70)
Exception stack(0xc04cdf70 to 0xc04cdfb8)
df60: 00000000 00000000 0000166e 00000000
df80: c04cc000 c050278f c050278f 00000001 c04d444c 410fc0f4 c03649b0 00000000
dfa0: 00000001 c04cdfb8 c000f758 c000f75c 60070013 ffffffff
[<c00123c0>] (__irq_svc+0x40/0x70) from [<c000f75c>] (arch_cpu_idle+0x28/0x30)
[<c000f75c>] (arch_cpu_idle+0x28/0x30) from [<c0054888>] (cpu_startup_entry+0x5c/0x148)
[<c0054888>] (cpu_startup_entry+0x5c/0x148) from [<c0497aa4>] (start_kernel+0x334/0x38c)
BUG: spinlock lockup suspected on CPU#0, kworker/0:1/360
lock: s3c24xx_serial_ports+0x1d8/0x370, .magic: dead4ead, .owner: <none>/-1, .owner_cpu: -1
CPU: 0 PID: 360 Comm: kworker/0:1 Not tainted 3.11.0-rc6-next-20130819-00003-g75485f1 #2
Workqueue: events flush_to_ldisc
[<c0014d58>] (unwind_backtrace+0x0/0xf8) from [<c0011908>] (show_stack+0x10/0x14)
[<c0011908>] (show_stack+0x10/0x14) from [<c035da34>] (dump_stack+0x6c/0xac)
[<c035da34>] (dump_stack+0x6c/0xac) from [<c01b581c>] (do_raw_spin_lock+0x100/0x17c)
[<c01b581c>] (do_raw_spin_lock+0x100/0x17c) from [<c03628a0>] (_raw_spin_lock_irqsave+0x20/0x28)
[<c03628a0>] (_raw_spin_lock_irqsave+0x20/0x28) from [<c0203224>] (uart_start+0x18/0x34)
[<c0203224>] (uart_start+0x18/0x34) from [<c01ef890>] (__receive_buf+0x4b4/0x738)
[<c01ef890>] (__receive_buf+0x4b4/0x738) from [<c01efb44>] (n_tty_receive_buf2+0x30/0x98)
[<c01efb44>] (n_tty_receive_buf2+0x30/0x98) from [<c01f2ba8>] (flush_to_ldisc+0xec/0x138)
[<c01f2ba8>] (flush_to_ldisc+0xec/0x138) from [<c0031af0>] (process_one_work+0xfc/0x348)
[<c0031af0>] (process_one_work+0xfc/0x348) from [<c0032138>] (worker_thread+0x138/0x37c)
[<c0032138>] (worker_thread+0x138/0x37c) from [<c0037a7c>] (kthread+0xa4/0xb0)
[<c0037a7c>] (kthread+0xa4/0xb0) from [<c000e5f8>] (ret_from_fork+0x14/0x3c)
-----
Release the port lock before calling tty_flip_buffer_push() and reacquire it
after the call.
Similar stuff was already done for few other drivers in the past, like:
commit 2389b27216
Author: Thomas Gleixner <tglx@linutronix.de>
Date: Tue May 29 21:53:50 2007 +0100
[ARM] 4417/1: Serial: Fix AMBA drivers locking
Cc: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit c441508421.
Kevin writes:
Hmm, another OMAP serial patch that wasn't Cc'd to linux-omap
where OMAP users might have seen it. :(
I just bisected a strange problem in linux-next on OMAP3 down to
this patch. Reverting it fixes the problem.
On OMAP3530 Beagle and Overo, after boot, doing a 'cat
/proc/cpuinfo' was not returning to a prompt, suggesting
something strange with the FIFO. Hitting return gets me back to
a prompt.
Greg, this one should also be dropped from tty-next until it can
be further investgated and the problem solved.
Reported-by: Kevin Hilman <khilman@linaro.org>
Cc: Dmitry Fink <finik@ti.com>
Cc: Alexander Savchenko <oleksandr.savchenko@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 908fd7e566.
Kevin writes:
Greg, without a better justification in the changelog, I think
this patch should be dropped from tty-next.
Reported-by: Kevin Hilman <khilman@linaro.org>
Cc: Ruchika Kharwar <ruchika@ti.com>
Cc: Alexander Savchenko <oleksandr.savchenko@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This solves a problem observed in kexec'ed kernel where 200ms timeout is
too short and bootconsole fails to initialize. Console did eventually
become workable but much later into the boot process.
Observed timeout was around 260ms, but I decided to make it a little bigger
for more reliability.
This has been tested on Power7 machine with Petitboot as a primary
bootloader and PowerNV firmware.
CC: <stable@vger.kernel.org>
Signed-off-by: Eugene Surovegin <surovegin@google.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
cleanup the clock API use of the UART driver which is shared among the
MPC512x and the MPC5200 platforms
- get, prepare, and enable the MCLK during port allocation; disable,
unprepare and put the MCLK upon port release; hold a reference to the
clock over the period of use; check for and propagate enable errors
- fix a buffer overflow for clock names with two digit PSC index numbers
- stick with the PPC_CLOCK 'psc%d_mclk' name for clock lookup, only
switch to a fixed string later after device tree based clock lookup
will have become available
to achieve support for MPC512x which is neutral to MPC5200, the
modification was done as follows
- introduce "clock alloc" and "clock release" routines in addition to
the previous "clock enable/disable" routine in the psc_ops struct
- make the clock allocation a part of the port request (resource
allocation), and make clock release a part of the port release, such
that essential resources get allocated early
- just enable/disable the clock from within the .clock() callback
without any allocation or preparation as the former implementation
did, since this routine is called from within the startup and shutdown
callbacks
- all of the above remains a NOP for the MPC5200 platform (no callbacks
are provided on that platform)
- implementation note: the clock gets enabled upon allocation already
just in case the clock is not only required for bitrate generation but
for register access as well
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
if we get the valid dma channels from dts, move to use dmaengine to do
rx/tx. because the dma hardware requires dma address and length to be
4bytes aligned, in this driver, we will still use PIO for non-aligned
bytes, and use dma for aligned bytes.
for rx, to keep the dmaengine always active, we use double-buffer, so
we issue two dma_desc at first, and maintain the status of both
1. dma transfer done: update in rx dma finish callback
2. dma buffer is inserted into tty: update in rx dma finish tasklet and
rx timeout tasklet
so we re-issue the dma_desc only if both 1&2 are finished.
for tx, as we know the actual length for every transfer, we don't need
the above double buffering.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
startup_uart_controller() loses namespace, this patch
drops the function directly and move the content into
sirfsoc_uart_startup().
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
fix the typo in commit 2eb5618de8 which uses two
gpios for rts/cts.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use devm_ioremap_resource instead of devm_request_and_ioremap.
This was done using the semantic patch
scripts/coccinelle/api/devm_ioremap_resource.cocci
and various manual modifications to move associated calls to
platform_get_resource closer to the resulting call to devm_ioremap_resource
and to remove the associated error handling code.
The initialization of port->mapbase is also moved lower, to take advantage
of the NULL test on res performed by devm_ioremap_resource.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is configured for RTS/CTS flow control, serial core
will disable the transmitter if it observes CTS is de-asserted. This is
perfectly reasonable and appropriate when the UART lacks the ability to
automatically perform CTS flow control.
However, if the UART hardware can manage flow control automatically, it
is important that software not get involved. When the DesignWare UART
enables 16C750 style auto-RTS/CTS it stops generating interrupts for
changes in CTS state so software mostly stays out of the way. However,
it does report the true state of CTS in the MSR so software may notice
it is de-asserted and respond by improperly disabling the transmitter.
Once this happens the transmitter will be blocked forever.
To avoid this situation, we simply lie to the 8250 and serial core by
reporting that CTS is asserted whenever auto-RTS/CTS mode is enabled.
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Reviewed-by: Markus Mayer <markus.mayer@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The recent patch to add RS485 contained a bug whereby the IER
interrupt was cleared down incorrectly.
This patch fixes the problem.
Signed-off-by: Mark Jackson <mpfj@newflow.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Function wait_for_xmitr is invoked only on functions that either depend
on CONFIG_CONSOLE_POLL or CONFIG_SERIAL_PCH_UART_CONSOLE.
This patch fixes the following warning:
drivers/tty/serial/pch_uart.c:1504:13: warning: ‘wait_for_xmitr’ defined but not used [-Wunused-function]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
for USP-based UART, we use two gpios as RTS and CST pins.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pinctrl core will get default pinmux, so drop it in the sirfsoc serial driver.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds RS485 support to the OMAP serial driver, as
defined in:-
Documentation/devicetree/bindings/serial/rs485.txt
When a UART transmitter is connected to (eg) a RS485 driver, it is
necessary to turn the driver on/off as quickly as possible. This is
best achieved in the serial driver itself (rather than in userspace
where the latency can be quite large).
This patch allows a GPIO pin to be defined (via DT) that controls
the enabling of the driver at the start of a message, and disables
the driver when the message has been completed.
When RS485 is disabled, the RTS pin is set to on.
Signed-off-by: Mark Jackson <mpfj@newflow.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove unneeded error handling on the result of a call to
platform_get_resource when the value is passed to devm_ioremap_resource.
Move the call to platform_get_resource adjacent to the call to
devm_ioremap_resource to make the connection between them more clear.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression pdev,res,n,e,e1;
expression ret != 0;
identifier l;
@@
- res = platform_get_resource(pdev, IORESOURCE_MEM, n);
... when != res
- if (res == NULL) { ... \(goto l;\|return ret;\) }
... when != res
+ res = platform_get_resource(pdev, IORESOURCE_MEM, n);
e = devm_ioremap_resource(e1, res);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adding a simple device tree binding for the specification of key
sequences. Definition of the keys found in the sequence are located in
'include/uapi/linux/input.h'.
For the sysrq driver, holding the sequence of keys down for a specific
amount of time will reset the system.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This change improves and cleans up the tile console.
- We enable HVC_IRQ support on tilegx, with the addition of a new
Tilera hypervisor API for tilegx to allow a console IPI. If IPI
support is not available we fall back to the previous polling mode.
- We simplify the earlyprintk code to use CON_BOOT and eliminate some
of the other supporting earlyprintk code.
- A new tile_console_write() primitive is used to send output to
the console and is factored out of the hvc_tile driver.
This lets us support a "sim_console" boot argument to allow using
simulator hooks to send output to the "console" as a slightly
faster alternative to emulating the hardware more directly.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The clock should be checked with the proper IS_ERR() api before using it.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable the clock if one is present when setting up the console.
Signed-off-by: Thomas Langer <thomas.langer@lantiq.com>
Acked-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__initdata should be placed between the variable name and equal
sign for the variable to be placed in the intended section.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__initdata should be placed between the variable name and equal
sign for the variable to be placed in the intended section.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'cons' is a pointer; thus NULL should be used instead of 0.
Also, local symbols are staticized.
Fix the following sparse warnings:
drivers/tty/serial/serial-tegra.c:1209:27: warning: Using plain integer as NULL pointer
drivers/tty/serial/serial-tegra.c:1240:29: warning: symbol 'tegra20_uart_chip_data' was not declared. Should it be static?
drivers/tty/serial/serial-tegra.c:1246:29: warning: symbol 'tegra30_uart_chip_data' was not declared. Should it be static?
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the following sparse warning:
drivers/tty/serial/msm_serial.c:237:37: error: incompatible types in comparison expression (different type sizes)
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Geert Uytterhoeven