Write, Write Zeroes, Zone append and a Zone Reset through
Zone Management Send modify the logical block content of a namespace,
so make sure the LBCC bit is reported for them.
Fixes: b5d0b38c0475 ("nvmet: add Command Set Identifier support")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Kanchan Joshi <joshi.k@samsung.com>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Use NVME_CMD_EFFECTS_CSUPP instead of open coding it and assign a
single value to multiple array entries instead of repeated assignments.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Kanchan Joshi <joshi.k@samsung.com>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
3 << 16 does not generate the correct mask for bits 16, 17 and 18.
Use the GENMASK macro to generate the correct mask instead.
Fixes: 84fef62d13 ("nvme: check admin passthru command effects")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Kanchan Joshi <joshi.k@samsung.com>
This adds a document about what specification features are supported by
the Linux NVMe driver, and what qualifies for a quirk if an implementation
has problems following the specification.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
The recent code refactoring for HD-audio HDMI codec driver caused a
regression on AMD/ATI HDMI codecs; namely, PulseAudioand pipewire
don't recognize HDMI outputs any longer while the direct output via
ALSA raw access still works.
The problem turned out that, after the code refactoring, the driver
assumes only the dynamic PCM assignment, and when a PCM stream that
still isn't assigned to any pin gets opened, the driver tries to
assign any free converter to the PCM stream. This behavior is OK for
Intel and other codecs, as they have arbitrary connections between
pins and converters. OTOH, on AMD chips that have a 1:1 mapping
between pins and converters, this may end up with blocking the open of
the next PCM stream for the pin that is tied with the formerly taken
converter.
Also, with the code refactoring, more PCM streams are exposed than
necessary as we assume all converters can be used, while this isn't
true for AMD case. This may change the PCM stream assignment and
confuse users as well.
This patch fixes those problems by:
- Introducing a flag spec->static_pcm_mapping, and if it's set, the
driver applies the static mapping between pins and converters at the
probe time
- Limiting the number of PCM streams per pins, too; this avoids the
superfluous PCM streams
Fixes: ef6f5494fa ("ALSA: hda/hdmi: Use only dynamic PCM device allocation")
Cc: <stable@vger.kernel.org>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216836
Co-developed-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20221228125714.16329-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
x86:
* several fixes to nested VMX execution controls
* fixes and clarification to the documentation for Xen emulation
* do not unnecessarily release a pmu event with zero period
* MMU fixes
* fix Coverity warning in kvm_hv_flush_tlb()
selftests:
* fixes for the ucall mechanism in selftests
* other fixes mostly related to compilation with clang
Commit 8fda37cf3d ("KVM: selftests: Stuff RAX/RCX with 'safe' values
in vmmcall()/vmcall()", 2022-11-21) broke the svm_nested_soft_inject_test
because it placed a "pop rbp" instruction after vmmcall. While this is
correct and mimics what is done in the VMX case, this particular test
expects a ud2 instruction right after the vmmcall, so that it can skip
over it in the L1 part of the test.
Inline a suitably-modified version of vmmcall() to restore the
functionality of the test.
Fixes: 8fda37cf3d ("KVM: selftests: Stuff RAX/RCX with 'safe' values in vmmcall()/vmcall()"
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20221130181147.9911-1-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Rudi reports a compilation failure on x86_64 when CONFIG_NET_CLS or
CONFIG_NET_CLS_ACT is not set but CONFIG_RETPOLINE is set.
A misplaced '#endif' was causing the issue.
Fixes: 7f0e810220 ("net/sched: add retpoline wrapper for tc")
Tested-by: Rudi Heitbaum <rudi@heitbaum.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Follow the advice of the Documentation/filesystems/sysfs.rst
and show() should only use sysfs_emit() or sysfs_emit_at()
when formatting the value to be returned to user space.
Signed-off-by: Xuezhi Zhang <zhangxuezhi1@coolpad.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chunhao Lin says:
====================
r8169: fix dmar pte write access is not set error
This series fixes dmar pte write access is not set error.
Chunhao Lin (2):
r8169: move rtl_wol_enable_rx() and rtl_prepare_power_down()
r8169: fix dmar pte write access is not set error
v2:
-update commit message
-adjust the code according to current kernel code
v3:
-update title and commit message
-split the patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When close device, if wol is enabled, rx will be enabled. When open
device it will cause rx packet to be dma to the wrong memory address
after pci_set_master() and system log will show blow messages.
DMAR: DRHD: handling fault status reg 3
DMAR: [DMA Write] Request device [02:00.0] PASID ffffffff fault addr
ffdd4000 [fault reason 05] PTE Write access is not set
In this patch, driver disable tx/rx when close device. If wol is
enabled, only enable rx filter and disable rxdv_gate(if support) to
let hardware only receive packet to fifo but not to dma it.
Signed-off-by: Chunhao Lin <hau@realtek.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no functional change. Moving these two functions for following
patch "r8169: fix dmar pte write access is not set error".
Signed-off-by: Chunhao Lin <hau@realtek.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniil Tatianin says:
====================
net/ethtool/ioctl: split ethtool_get_phy_stats into multiple helpers
This series fixes a potential NULL dereference in ethtool_get_phy_stats
while also attempting to refactor/split said function into multiple
helpers so that it's easier to reason about what's going on.
I've taken Andrew Lunn's suggestions on the previous version of this
patch and added a bit of my own.
Changes since v1:
- Remove an extra newline in the first patch
- Move WARN_ON_ONCE into the if check as it already returns the
result of the comparison
- Actually split ethtool_get_phy_stats instead of attempting to
refactor it
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
So that it's easier to follow and make sense of the branching and
various conditions.
Stats retrieval has been split into two separate functions
ethtool_get_phy_stats_phydev & ethtool_get_phy_stats_ethtool.
The former attempts to retrieve the stats using phydev & phy_ops, while
the latter uses ethtool_ops.
Actual n_stats validation & array allocation has been moved into a new
ethtool_vzalloc_stats_array helper.
This also fixes a potential NULL dereference of
ops->get_ethtool_phy_stats where it was getting called in an else branch
unconditionally without making sure it was actually present.
Found by Linux Verification Center (linuxtesting.org) with the SVACE
static analysis tool.
Signed-off-by: Daniil Tatianin <d-tatianin@yandex-team.ru>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we always early return if we don't have any stats we can remove
these checks as they're no longer necessary.
Signed-off-by: Daniil Tatianin <d-tatianin@yandex-team.ru>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's not very useful to copy back an empty ethtool_stats struct and
return 0 if we didn't actually have any stats. This also allows for
further simplification of this function in the future commits.
Signed-off-by: Daniil Tatianin <d-tatianin@yandex-team.ru>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently only the locking order of SRCU vs kvm->slots_arch_lock
and kvm->slots_lock is documented. Extend this to kvm->lock
since Xen emulation got it terribly wrong.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
While KVM_XEN_EVTCHN_RESET is usually called with no vCPUs running,
if that happened it could cause a deadlock. This is due to
kvm_xen_eventfd_reset() doing a synchronize_srcu() inside
a kvm->lock critical section.
To avoid this, first collect all the evtchnfd objects in an
array and free all of them once the kvm->lock critical section
is over and th SRCU grace period has expired.
Reported-by: Michal Luczaj <mhal@rbox.co>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The virtblk_map_data() function returns negative error codes, however, the
'nents' field of vbr->sg_table is an unsigned int, which causes the error
handling not to work correctly.
Cc: stable@vger.kernel.org
Fixes: 0e9911fa76 ("virtio-blk: support mq_ops->queue_rqs()")
Signed-off-by: Rafael Mendonca <rafaelmendsr@gmail.com>
Message-Id: <20221021204126.927603-1-rafaelmendsr@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Suwan Kim <suwan.kim027@gmail.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
In the receive_filter(), should not drop the packet with the
broadcast/multicast address. Add the check for this
Signed-off-by: Cindy Lu <lulu@redhat.com>
Message-Id: <20221214054306.24145-1-lulu@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
After commit bda324fd03 ("vdpasim: control virtqueue support"),
vdpasim->iommu became an array of IOTLB, so we should clean the
mappings of each free one by one instead of just deleting the ranges
in the first IOTLB which may leak maps.
Fixes: bda324fd03 ("vdpasim: control virtqueue support")
Cc: Gautam Dawar <gautam.dawar@xilinx.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20221213090717.61529-1-jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Gautam Dawar <gautam.dawar@amd.com>
For the device without multiqueue feature, we will read 0 as
max_virtqueue_pairs from the config. So if we fill
VDPA_ATTR_DEV_NET_CFG_MAX_VQP with the value we read from the config
we will confuse the user.
Fixing this by only filling the value when multiqueue is offered by
the device so userspace can assume 1 when the attr is not provided.
Fixes: 13b00b135665c("vdpa: Add support for querying vendor statistics")
Cc: Eli Cohen <elic@nvidia.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20220907060110.4511-1-jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eli Cohen <elic@nvidia.com>
In vp_vdpa_remove(), the code kfree(&vp_vdpa_mgtdev->mgtdev.id_table) uses
a reference of pointer as the argument of kfree, which is the wrong pointer
and then may hit crash like this:
Unable to handle kernel paging request at virtual address 00ffff003363e30c
Internal error: Oops: 96000004 [#1] SMP
Call trace:
rb_next+0x20/0x5c
ext4_readdir+0x494/0x5c4 [ext4]
iterate_dir+0x168/0x1b4
__se_sys_getdents64+0x68/0x170
__arm64_sys_getdents64+0x24/0x30
el0_svc_common.constprop.0+0x7c/0x1bc
do_el0_svc+0x2c/0x94
el0_svc+0x20/0x30
el0_sync_handler+0xb0/0xb4
el0_sync+0x160/0x180
Code: 54000220 f9400441 b4000161 aa0103e0 (f9400821)
SMP: stopping secondary CPUs
Starting crashdump kernel...
Fixes: ffbda8e9df ("vdpa/vp_vdpa : add vdpa tool support in vp_vdpa")
Signed-off-by: Rong Wang <wangrong68@huawei.com>
Signed-off-by: Nanyong Sun <sunnanyong@huawei.com>
Message-Id: <20221207120813.2837529-1-sunnanyong@huawei.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cindy Lu <lulu@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Add a limit to 'config->vq_num' which is user controlled data which
comes from an vduse_ioctl to prevent large memory allocations.
Micheal says - This limit is somewhat arbitrary.
However, currently virtio pci and ccw are limited to a 16 bit vq number.
While MMIO isn't it is also isn't used with lots of VQs due to
current lack of support for per-vq interrupts.
Thus, the 0xffff limit on number of VQs corresponding
to a 16-bit VQ number seems sufficient for now.
This is found using static analysis with smatch.
Suggested-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Message-Id: <20221128155717.2579992-1-harshit.m.mogalapalli@oracle.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
This gets rid of the last references to smp_read_barrier_depends()
which for the kernel side was removed in v5.9. The serialization
required for Alpha is done inside READ_ONCE() instead of having
users deal with it. Simply use a full barrier, the architecture
does not have rmb in the first place.
Signed-off-by: Davidlohr Bueso <dave@stgolabs.net>
Message-Id: <20221128034347.990-3-dave@stgolabs.net>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
__read_once_size() is not a macro, remove those '/'s.
Signed-off-by: Davidlohr Bueso <dave@stgolabs.net>
Message-Id: <20221128034347.990-2-dave@stgolabs.net>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Replace sprintf with sysfs_emit or its variants for their
built-in PAGE_SIZE awareness.
Signed-off-by: Dawei Li <set_pte_at@outlook.com>
Message-Id: <TYCP286MB23232A999FE7DBDF50BA0FAACA0F9@TYCP286MB2323.JPNP286.PROD.OUTLOOK.COM>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
'vc_ctrl_req' is alloced in virtio_crypto_alg_skcipher_close_session(),
and should be freed in the invalid ctrl_status->status error handling
case. Otherwise there is a memory leak.
Fixes: 0756ad15b1 ("virtio-crypto: use private buffer for control request")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Message-Id: <20221114110740.537276-1-weiyongjun@huaweicloud.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Gonglei <arei.gonglei@huawei.com>
Acked-by: zhenwei pi<pizhenwei@bytedance.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Replace "unsigned" with "unsigned int"
Signed-off-by: wangjianli <wangjianli@cdjrlc.com>
Message-Id: <20221113070742.48271-1-wangjianli@cdjrlc.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When we initialize vringh, we should pass the features and the
number of elements in the virtqueue negotiated with the driver,
otherwise operations with vringh may fail.
This was discovered in a case where the driver sets a number of
elements in the virtqueue different from the value returned by
.get_vq_num_max().
In vdpasim_vq_reset() is safe to initialize the vringh with
default values, since the virtqueue will not be used until
vdpasim_queue_ready() is called again.
Fixes: 2c53d0f64c ("vdpasim: vDPA device simulator")
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <20221110141335.62171-1-sgarzare@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Eugenio Pérez <eperezma@redhat.com>
We use UINT_MAX to limit max_discard_sectors in virtblk_probe,
we can use UINT_MAX to limit max_hw_sectors for consistencies.
No functional change intended.
Signed-off-by: Angus Chen <angus.chen@jaguarmicro.com>
Message-Id: <20221110030124.1986-1-angus.chen@jaguarmicro.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Before commit 3d56987938 ("vhost-vdpa: introduce asid based IOTLB")
we called vhost_vdpa_iotlb_unmap(v, iotlb, 0ULL, 0ULL - 1) during
release to free all the resources allocated when processing user IOTLB
messages through vhost_vdpa_process_iotlb_update().
That commit changed the handling of IOTLB a bit, and we accidentally
removed some code called during the release.
We partially fixed this with commit 037d430556 ("vhost-vdpa: call
vhost_vdpa_cleanup during the release") but a potential memory leak is
still there as showed by kmemleak if the application does not send
VHOST_IOTLB_INVALIDATE or crashes:
unreferenced object 0xffff888007fbaa30 (size 16):
comm "blkio-bench", pid 914, jiffies 4294993521 (age 885.500s)
hex dump (first 16 bytes):
40 73 41 07 80 88 ff ff 00 00 00 00 00 00 00 00 @sA.............
backtrace:
[<0000000087736d2a>] kmem_cache_alloc_trace+0x142/0x1c0
[<0000000060740f50>] vhost_vdpa_process_iotlb_msg+0x68c/0x901 [vhost_vdpa]
[<0000000083e8e205>] vhost_chr_write_iter+0xc0/0x4a0 [vhost]
[<000000008f2f414a>] vhost_vdpa_chr_write_iter+0x18/0x20 [vhost_vdpa]
[<00000000de1cd4a0>] vfs_write+0x216/0x4b0
[<00000000a2850200>] ksys_write+0x71/0xf0
[<00000000de8e720b>] __x64_sys_write+0x19/0x20
[<0000000018b12cbb>] do_syscall_64+0x3f/0x90
[<00000000986ec465>] entry_SYSCALL_64_after_hwframe+0x63/0xcd
Let's fix this calling vhost_vdpa_iotlb_unmap() on the whole range in
vhost_vdpa_remove_as(). We move that call before vhost_dev_cleanup()
since we need a valid v->vdev.mm in vhost_vdpa_pa_unmap().
vhost_iotlb_reset() call can be removed, since vhost_vdpa_iotlb_unmap()
on the whole range removes all the entries.
The kmemleak log reported was observed with a vDPA device that has `use_va`
set to true (e.g. VDUSE). This patch has been tested with both types of
devices.
Fixes: 037d430556 ("vhost-vdpa: call vhost_vdpa_cleanup during the release")
Fixes: 3d56987938 ("vhost-vdpa: introduce asid based IOTLB")
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <20221109154213.146789-1-sgarzare@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
vhost_iotlb_itree_first() requires `start` and `last` parameters
to search for a mapping that overlaps the range.
In translate_desc() we cyclically call vhost_iotlb_itree_first(),
incrementing `addr` by the amount already translated, so rightly
we move the `start` parameter passed to vhost_iotlb_itree_first(),
but we should hold the `last` parameter constant.
Let's fix it by saving the `last` parameter value before incrementing
`addr` in the loop.
Fixes: a9709d6874 ("vhost: convert pre sorted vhost memory array to interval tree")
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <20221109102503.18816-3-sgarzare@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
vhost_iotlb_itree_first() requires `start` and `last` parameters
to search for a mapping that overlaps the range.
In iotlb_translate() we cyclically call vhost_iotlb_itree_first(),
incrementing `addr` by the amount already translated, so rightly
we move the `start` parameter passed to vhost_iotlb_itree_first(),
but we should hold the `last` parameter constant.
Let's fix it by saving the `last` parameter value before incrementing
`addr` in the loop.
Fixes: 9ad9c49cfe ("vringh: IOTLB support")
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <20221109102503.18816-2-sgarzare@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
A problem about modprobe vhost_vsock failed is triggered with the
following log given:
modprobe: ERROR: could not insert 'vhost_vsock': Device or resource busy
The reason is that vhost_vsock_init() returns misc_register() directly
without checking its return value, if misc_register() failed, it returns
without calling vsock_core_unregister() on vhost_transport, resulting the
vhost_vsock can never be installed later.
A simple call graph is shown as below:
vhost_vsock_init()
vsock_core_register() # register vhost_transport
misc_register()
device_create_with_groups()
device_create_groups_vargs()
dev = kzalloc(...) # OOM happened
# return without unregister vhost_transport
Fix by calling vsock_core_unregister() when misc_register() returns error.
Fixes: 433fc58e6b ("VSOCK: Introduce vhost_vsock.ko")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Message-Id: <20221108101705.45981-1-yuancan@huawei.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Unneeded semicolon after curly braces, so delete it.
Signed-off-by: Shaomin Deng <dengshaomin@cdjrlc.com>
Message-Id: <20221105155151.12155-1-dengshaomin@cdjrlc.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Virtio_crypto use max_data_queues+1 to setup vqs,
we use vp_modern_get_num_queues to protect the vq range in setup_vq.
We could enter index >= vp_modern_get_num_queues(mdev) in setup_vq
if common->num_queues is not set well,and it return -ENOENT.
It is better to use -EINVAL instead.
Signed-off-by: Angus Chen <angus.chen@jaguarmicro.com>
Message-Id: <20221101111655.1947-1-angus.chen@jaguarmicro.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Variable i is just being incremented and it's never used
anywhere else. The variable and the increment are redundant so
remove it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Message-Id: <20221024133756.2158497-1-colin.i.king@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Use helper function is_power_of_2() to check if num is power of two.
Minor readability improvement.
Signed-off-by: Shaoqin Huang <shaoqin.huang@intel.com>
Message-Id: <20221021062734.228881-3-shaoqin.huang@intel.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Use helper function is_power_of_2() to check if num is power of two.
Minor readability improvement.
Signed-off-by: Shaoqin Huang <shaoqin.huang@intel.com>
Message-Id: <20221021062734.228881-2-shaoqin.huang@intel.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
When qemu uses different address spaces for data and control virtqueues,
the current code would overwrite the control virtqueue iotlb through the
dup_iotlb call. Fix this by referring to the address space identifier
and the group to asid mapping to determine which mapping needs to be
updated. We also move the address space logic from mlx5 net to core
directory.
Reported-by: Eugenio Pérez <eperezma@redhat.com>
Signed-off-by: Eli Cohen <elic@nvidia.com>
Message-Id: <20221114131759.57883-6-elic@nvidia.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Eugenio Pérez <eperezma@redhat.com>
event_handler runs under atomic context and may not acquire reslock. We
can still guarantee that the handler won't be called after suspend by
clearing nb_registered, unregistering the handler and flushing the
workqueue.
Signed-off-by: Eli Cohen <elic@nvidia.com>
Message-Id: <20221114131759.57883-5-elic@nvidia.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Delete the old MAC from the table and not the new one which is not there
yet.
Fixes: baf2ad3f6a ("vdpa/mlx5: Add RX MAC VLAN filter support")
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Eli Cohen <elic@nvidia.com>
Message-Id: <20221114131759.57883-4-elic@nvidia.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Check if VIRTIO_NET_F_CTRL_VLAN is negotiated and return error if
control VQ command is received.
Signed-off-by: Eli Cohen <elic@nvidia.com>
Message-Id: <20221114131759.57883-3-elic@nvidia.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Eugenio Pérez <eperezma@redhat.com>
Set the VLAN id to the header values field instead of overwriting the
headers criteria field.
Before this fix, VLAN filtering would not really work and tagged packets
would be forwarded unfiltered to the TIR.
Fixes: baf2ad3f6a ("vdpa/mlx5: Add RX MAC VLAN filter support")
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Eli Cohen <elic@nvidia.com>
Message-Id: <20221114131759.57883-2-elic@nvidia.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The fotg210 module combines the HCD and OTG drivers, which then
fails to build when only the USB gadget support is enabled
in the kernel but host support is not:
aarch64-linux-ld: drivers/usb/fotg210/fotg210-core.o: in function `fotg210_init':
fotg210-core.c:(.init.text+0xc): undefined reference to `usb_disabled'
Move the check for usb_disabled() after the check for the HCD module,
and let the OTG driver still be probed in this configuration.
A nicer approach might be to have the common portion built as a
library module, with the two platform other files registering
their own platform_driver instances separately.
Fixes: ddacd6ef44 ("usb: fotg210: Fix Kconfig for USB host modules")
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20221215165728.2062984-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michael Chan says:
====================
bnxt_en: Bug fixes
This series fixes a devlink bug and several XDP related bugs. The
devlink bug causes a kernel crash on VF devices. The XDP driver
patches fix and clean up the RX XDP path and re-enable header-data
split that was disabled by mistake when adding the XDP multi-buffer
support.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Christoph Hellwig