When CONFIG_OF=n of_match_device() gets pre-processed out of existence
leaving qcom-smmu_client_of_match unused. Mark it as possibly unused to
keep the compiler from warning in that case.
Fixes: 0e764a0101 ("iommu/arm-smmu: Allow client devices to select direct mapping")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20200604203905.31964-1-jcrouse@codeaurora.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The modem remote processor has two access paths to DDR. One path is
directly connected to DDR and another path goes through an SMMU. The
SMMU path is configured to be a direct mapping because it's used by
various peripherals in the modem subsystem. Typically this direct
mapping is configured statically at EL2 by QHEE (Qualcomm's Hypervisor
Execution Environment) before the kernel is entered.
In certain firmware configuration, especially when the kernel is already
in full control of the SMMU, defer programming the modem SIDs to the
kernel. Let's add compatibles here so that we can have the kernel
program the SIDs for the modem in these cases.
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20200511175532.25874-1-sibis@codeaurora.org
Signed-off-by: Will Deacon <will@kernel.org>
Some client devices want to directly map the IOMMU themselves instead
of using the DMA domain. Allow those devices to opt in to direct
mapping by way of a list of compatible strings.
Co-developed-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/7cf1f64167b5545b7f42275395be1f1e2ea3a6ac.1587407458.git.saiprakash.ranjan@codeaurora.org
Signed-off-by: Will Deacon <will@kernel.org>
Currently the QCOM specific smmu reset implementation is very
specific to SDM845 SoC and has a wait-for-safe logic which
may not be required for other SoCs. So move the SDM845 specific
logic to its specific reset function. Also add SC7180 SMMU
compatible for calling into QCOM specific implementation.
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/d24a0278021bc0b2732636c5728efe55e7318a8b.1587407458.git.saiprakash.ranjan@codeaurora.org
Signed-off-by: Will Deacon <will@kernel.org>
Add reset hook for sdm845 based platforms to turn off
the wait-for-safe sequence.
Understanding how wait-for-safe logic affects USB and UFS performance
on MTP845 and DB845 boards:
Qcom's implementation of arm,mmu-500 adds a WAIT-FOR-SAFE logic
to address under-performance issues in real-time clients, such as
Display, and Camera.
On receiving an invalidation requests, the SMMU forwards SAFE request
to these clients and waits for SAFE ack signal from real-time clients.
The SAFE signal from such clients is used to qualify the start of
invalidation.
This logic is controlled by chicken bits, one for each - MDP (display),
IFE0, and IFE1 (camera), that can be accessed only from secure software
on sdm845.
This configuration, however, degrades the performance of non-real time
clients, such as USB, and UFS etc. This happens because, with wait-for-safe
logic enabled the hardware tries to throttle non-real time clients while
waiting for SAFE ack signals from real-time clients.
On mtp845 and db845 devices, with wait-for-safe logic enabled by the
bootloaders we see degraded performance of USB and UFS when kernel
enables the smmu stage-1 translations for these clients.
Turn off this wait-for-safe logic from the kernel gets us back the perf
of USB and UFS devices until we re-visit this when we start seeing perf
issues on display/camera on upstream supported SDM845 platforms.
The bootloaders on these boards implement secure monitor callbacks to
handle a specific command - QCOM_SCM_SVC_SMMU_PROGRAM with which the
logic can be toggled.
There are other boards such as cheza whose bootloaders don't enable this
logic. Such boards don't implement callbacks to handle the specific SCM
call so disabling this logic for such boards will be a no-op.
This change is inspired by the downstream change from Patrick Daly
to address performance issues with display and camera by handling
this wait-for-safe within separte io-pagetable ops to do TLB
maintenance. So a big thanks to him for the change and for all the
offline discussions.
Without this change the UFS reads are pretty slow:
$ time dd if=/dev/sda of=/dev/zero bs=1048576 count=10 conv=sync
10+0 records in
10+0 records out
10485760 bytes (10.0MB) copied, 22.394903 seconds, 457.2KB/s
real 0m 22.39s
user 0m 0.00s
sys 0m 0.01s
With this change they are back to rock!
$ time dd if=/dev/sda of=/dev/zero bs=1048576 count=300 conv=sync
300+0 records in
300+0 records out
314572800 bytes (300.0MB) copied, 1.030541 seconds, 291.1MB/s
real 0m 1.03s
user 0m 0.00s
sys 0m 0.54s
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Signed-off-by: Will Deacon <will@kernel.org>
Jordan Crouse