The reference manuals of both the RX8803 and RV8803 dictate that
"[On V2F/VLF = ] all registers must be initialized".
The RV-8803 application manual (rev. 1.6) further specifies that crossing
V_LOW2 threshold enables flag V2F and triggers a Power-On reset.
According to table 3.11 in the document, all control registers are
defined to sensible values.
However, The Epson RX-8803 doesn't offer the same guarantees.
It explicitly states:
During the initial power-up, the TEST bit is reset to "0" and the VLF
bit is set to "1".
∗ At this point, all other register values are _undefined_, so be sure to
perform a reset before using the module.
Commit d3700b6b64 ("rtc: rv8803: Stop the clock while setting the time")
also had this rationale:
Indeed, all the registers must be initialized if the voltage has been
lower than VLOW2 (triggering V2F), but not low enough to trigger a POR.
We should follow the advice and initialize all applicable registers.
We can group the registers into 3 groups:
A) Already correctly handled registers:
* 0B-0Ch | Timer Counter | unused and disabled by clearing TE in 0Dh
* 0Dh | Extension Reg | already initialized in rv8803_regs_configure
* 0Eh | Flag Reg | handled in IRQ handler, except for VLF, VDET
* 0Eh | VLF, VDET | cleared in ->set_time
* 10h | 100th Seconds | Already reset via RESET bit
* 20-21h | Capture Buffer | holds timestamp unused by driver
* 2Fh | Event Control | resets automatically
B) Registers that are hardware initialized on POR, but not on VLF:
* 0Fh | Control Reg
* 2Ch | OSC Offset
C) RAM that is undefined on voltage loss:
* 00-06h | Date/Time
* 07h | RAM
* 08-0Ah | Alarm
This means we should initialize after VLF the registers in group B
(RV8803_CTRL and RV8803_OSC_OFFSET).
Group C is all-zero after voltage loss on the RV-8803, but undefined on
the RX-8803. This is ok for Date/Time because ->get_time returns an
error code for as long as the voltage loss flag is active. It's cleared
on ->set_time however. Zeroing both RAM and alarm ensures a fixed value
is read afterwards.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220426071056.1187235-4-s.hauer@pengutronix.de
The driver probe currently initializes some registers to non-POR
values. These values are not reinstated if the RTC experiences voltage
loss later on. Fix this.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220426071056.1187235-3-s.hauer@pengutronix.de
The driver probe currently initializes some registers to non-POR
values. These values are not reinstated if the RTC experiences voltage
loss later on. Prepare for fixing this by factoring out the
initialization to a separate function.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220426071056.1187235-2-s.hauer@pengutronix.de
Waiting 1ms every time is not necessary, for example on some AMD boxes
the RTC_UIP bit is documented as being high for around 270 microseconds
in some cases [1], which agreed with experiments on an SB710
southbridge. So 100us seems optimal.
This in preparation for mach_get_cmos_time() refactoring.
The functions mc146818_get_time() and mach_get_cmos_time() in
arch/x86/kernel/rtc.c perform the same function and the code is
duplicated. mach_get_cmos_time() is busy waiting for the RTC_UIP
bit to clear, so make mc146818_get_time() more similar to it by reducing
the polling period.
[1] AMD SB700/710/750 Register Reference Guide, page 307,
https://developer.amd.com/wordpress/media/2012/10/43009_sb7xx_rrg_pub_1.00.pdf
"SB700 A12: The UIP high pulse is 270 μS Typical when SS on SRC
clock is OFF and 100μ min when SRC SS is ON." [sic]
Signed-off-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: x86@kernel.org
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220225215011.861477-2-mat.jonczyk@o2.pl
The second part of the multiplatform changes now converts the
Intel/Marvell PXA platform along with the rest. The patches went through
several rebases before the merge window as bugs were found, so they
remained separate.
This has to touch a lot of drivers, in particular the touchscreen,
pcmcia, sound and clk bits, to detach the driver files from the
platform and board specific header files.
-----BEGIN PGP SIGNATURE-----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=cnSb
-----END PGP SIGNATURE-----
Merge tag 'arm-multiplatform-5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull more ARM multiplatform updates from Arnd Bergmann:
"The second part of the multiplatform changes now converts the
Intel/Marvell PXA platform along with the rest. The patches went
through several rebases before the merge window as bugs were found, so
they remained separate.
This has to touch a lot of drivers, in particular the touchscreen,
pcmcia, sound and clk bits, to detach the driver files from the
platform and board specific header files"
* tag 'arm-multiplatform-5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (48 commits)
ARM: pxa/mmp: remove traces of plat-pxa
ARM: pxa: convert to multiplatform
ARM: pxa/sa1100: move I/O space to PCI_IOBASE
ARM: pxa: remove support for MTD_XIP
ARM: pxa: move mach/*.h to mach-pxa/
ARM: PXA: fix multi-cpu build of xsc3
ARM: pxa: move plat-pxa to drivers/soc/
ARM: mmp: rename pxa_register_device
ARM: mmp: remove tavorevb board support
ARM: pxa: remove unused mach/bitfield.h
ARM: pxa: move clk register definitions to driver
ARM: pxa: move smemc register access from clk to platform
cpufreq: pxa3: move clk register access to clk driver
ARM: pxa: remove get_clk_frequency_khz()
ARM: pxa: pcmcia: move smemc configuration back to arch
ASoC: pxa: i2s: use normal MMIO accessors
ASoC: pxa: ac97: use normal MMIO accessors
ASoC: pxa: use pdev resource for FIFO regs
Input: wm97xx - get rid of irq_enable method in wm97xx_mach_ops
Input: wm97xx - switch to using threaded IRQ
...
New driver:
- Renesas RZN1 rtc
Drivers:
- sun6i: Add nvmem support
-----BEGIN PGP SIGNATURE-----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=D9z8
-----END PGP SIGNATURE-----
Merge tag 'rtc-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"A new driver represents the bulk of the changes and then we get the
usual small fixes.
New driver:
- Renesas RZN1 rtc
Drivers:
- sun6i: Add nvmem support"
* tag 'rtc-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
rtc: mxc: Silence a clang warning
rtc: rzn1: Fix a variable type
rtc: rzn1: Fix error code in probe
rtc: rzn1: Avoid mixing variables
rtc: ftrtc010: Fix error handling in ftrtc010_rtc_probe
rtc: mt6397: check return value after calling platform_get_resource()
rtc: rzn1: fix platform_no_drv_owner.cocci warning
rtc: gamecube: Add missing iounmap in gamecube_rtc_read_offset_from_sram
rtc: meson: Fix email address in MODULE_AUTHOR
rtc: simplify the return expression of rx8025_set_offset()
rtc: pcf85063: Add a compatible entry for pca85073a
dt-binding: pcf85063: Add an entry for pca85073a
MAINTAINERS: Add myself as maintainer of the RZN1 RTC driver
rtc: rzn1: Add oscillator offset support
rtc: rzn1: Add alarm support
rtc: rzn1: Add new RTC driver
dt-bindings: rtc: rzn1: Describe the RZN1 RTC
rtc: sun6i: Add NVMEM provider
Change the of_device_get_match_data() cast to (uintptr_t)
to silence the following clang warning:
drivers/rtc/rtc-mxc.c:315:19: warning: cast to smaller integer type 'enum imx_rtc_type' from 'const void *' [-Wvoid-pointer-to-enum-cast]
Reported-by: kernel test robot <lkp@intel.com>
Fixes: ba7aa63000 ("rtc: mxc: use of_device_get_match_data")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220526011459.1167197-1-festevam@gmail.com
The calculation in ->set_offset() handles both negative and positive
offsets. The 'steps' variable will be checked to be in a specific [-x;
+x] range, which means it must be a signed integer rather than
unsigned.
This also fixes the following smatch warning:
warn: 'steps' 'true' implies 'steps > 0' is 'true'
Fixes: be4a11cf98 ("rtc: rzn1: Add oscillator offset support")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220520082500.489248-1-miquel.raynal@bootlin.com
There is a copy and paste error so this code returns the wrong variable.
Fixes: deeb4b5393 ("rtc: rzn1: Add new RTC driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/YoZMg1dmHHSJEfE9@kili
In the ->set_offset() callback, the 'val' variable is used for two
different purposes at the same time, which is oviously wrong:
- It contains the intermediate value of the SUBU register that must be
written at the end of ->set_offset().
- It is used in the middle of the above calculations to poll the CTL2
register for a specific value.
Let's introduce a 'ctl2' variable just for the readl_poll_timeout()
call and use it there in place of 'var'.
In order to avoid mixing those two variables again, let's rename the
remaining occurences of 'val' into 'subu' and initialize it to 0 to
avoid the uninitialized variable situation reported by Tom Rix and Colin
Ian King already.
Fixes: be4a11cf98 ("rtc: rzn1: Add oscillator offset support")
Reported-by: Tom Rix <trix@redhat.com>
Reported-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220520082221.488849-1-miquel.raynal@bootlin.com
- Introduce virtual m68k machine based on Android Goldfish devices,
- Defconfig updates,
- Minor fixes and improvements.
-----BEGIN PGP SIGNATURE-----
iIsEABYIADMWIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCYotRMhUcZ2VlcnRAbGlu
dXgtbTY4ay5vcmcACgkQisJQ/WRJ8XDFmgD/ZFTY4HashrodaQQLeRnwF1e2fDSY
yvpDfaJJf9vJY0kBAM/yflOMfPHeUOe1rLY0twevuZTgDUIv4f+Oi+9jtYUN
=ccFr
-----END PGP SIGNATURE-----
Merge tag 'm68k-for-v5.19-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
Pull m68k updates from Geert Uytterhoeven:
- Introduce virtual m68k machine based on Android Goldfish devices
- defconfig updates
- Minor fixes and improvements
* tag 'm68k-for-v5.19-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: atari: Make Atari ROM port I/O write macros return void
m68k: math-emu: Fix dependencies of math emulation support
m68k: math-emu: Fix typos in comments
m68k: Wire up syscall_trace_enter/leave for m68k
m68k: defconfig: Update defconfigs for v5.18-rc1
m68k: Introduce a virtual m68k machine
clocksource/drivers: Add a goldfish-timer clocksource
rtc: goldfish: Use gf_ioread32()/gf_iowrite32()
tty: goldfish: Introduce gf_ioread32()/gf_iowrite32()
In the error handling path, the clk_prepare_enable() function
call should be balanced by a corresponding 'clk_disable_unprepare()'
call , as already done in the remove function.
clk_disable_unprepare calls clk_disable() and clk_unprepare().
They will use IS_ERR_OR_NULL to check the argument.
Fixes: ac05fba39c ("rtc: gemini: Add optional clock handling")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220403054912.31739-1-linmq006@gmail.com
It will cause null-ptr-deref if platform_get_resource() returns NULL,
we need check the return value.
Fixes: fc2979118f ("rtc: mediatek: Add MT6397 RTC driver")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220505125043.1594771-1-yangyingliang@huawei.com
Remove .owner field if calls are used which set it automatically.
./drivers/rtc/rtc-rzn1.c:411:3-8: No need to set .owner here. The core
will do it.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220518232445.79156-1-yang.lee@linux.alibaba.com
The hw_srnprot needs to be unmapped when gamecube_rtc_read_offset_from_sram returns.
Fixs: 86559400b3 (rtc: gamecube: Add a RTC driver for the GameCube, Wii and Wii U)
Signed-off-by: Yuan Can <yuancan@huawei.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220511071354.46202-1-yuancan@huawei.com
The PCA85073A RTC has the same programming model as the PCF85063A.
Add a compatible entry for it.
Tested on a custom i.MX6SX based board.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220419014445.341444-2-festevam@gmail.com
The RZN1 RTC can compensate the imprecision of the oscillator up to
approximately 190ppm.
Seconds can last slightly shorter or longer depending on the
configuration.
Below ~65ppm of correction, we can change the time spent in a second
every minute, which is the most accurate compensation that the RTC can
offer. Above, the compensation will be active every 20s.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220516082504.33913-5-miquel.raynal@bootlin.com
The RZN1 RTC can trigger an interrupt when reaching a particular date up
to 7 days ahead. Bring support for this alarm.
One drawback though, the granularity is about a minute.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220516082504.33913-4-miquel.raynal@bootlin.com
The sun6i RTC provides 32 bytes of general-purpose data registers.
They can be used to save data in the always-on RTC power domain.
The registers are writable via 32-bit MMIO accesses only.
Expose them with a NVMEM provider so they can be used by other drivers.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220413231731.56709-1-samuel@sholland.org
The mach/hardware.h is included in lots of places, and it provides
three different things on pxa:
- the cpu_is_pxa* macros
- an indirect inclusion of mach/addr-map.h
- the __REG() and io_pv2() helper macros
Split it up into separate <linux/soc/pxa/cpu.h> and mach/pxa-regs.h
headers, then change all the files that use mach/hardware.h to
include the exact set of those three headers that they actually
need, allowing for further more targeted cleanup.
linux/soc/pxa/cpu.h can remain permanently exported and is now in
a global location along with similar headers. pxa-regs.h and
addr-map.h are only used in a very small number of drivers now
and can be moved to arch/arm/mach-pxa/ directly when those drivers
are to pass the necessary data as resources.
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Acked-by: Mark Brown <broonie@kernel.org>
Cc: linux-clk@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Cc: linux-input@vger.kernel.org
Cc: linux-leds@vger.kernel.org
Cc: linux-mmc@vger.kernel.org
Cc: linux-mtd@lists.infradead.org
Cc: linux-rtc@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: linux-fbdev@vger.kernel.org
Cc: linux-watchdog@vger.kernel.org
Cc: alsa-devel@alsa-project.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add a clocksource based on the goldfish-rtc device.
Move the timer register definition to <clocksource/timer-goldfish.h>
This kernel implementation is based on the QEMU upstream implementation:
https://git.qemu.org/?p=qemu.git;a=blob_plain;f=hw/rtc/goldfish_rtc.c
goldfish-timer is a high-precision signed 64-bit nanosecond timer.
It is part of the 'goldfish' virtual hardware platform used to run
some emulated Android systems under QEMU.
This timer only supports oneshot event.
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20220406201523.243733-4-laurent@vivier.eu
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Subsystem:
- remove uie_unsupported, all users have been converted to clear
RTC_FEATURE_UPDATE_INTERRUPT and provide a reason
- RTCs with an alarm with a resolution of a minute are now letting the core
handle rounding down the alarm time
- fix use-after-free on device removal
New driver:
- OP-TEE RTC PTA
Drivers:
- sun6i: Add H616 support
- cmos: Fix the AltCentury for AMD platforms
- spear: set range
-----BEGIN PGP SIGNATURE-----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=7E0a
-----END PGP SIGNATURE-----
Merge tag 'rtc-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"The bulk of the patches are about replacing the uie_unsupported struct
rtc_device member by a feature bit.
Subsystem:
- remove uie_unsupported, all users have been converted to clear
RTC_FEATURE_UPDATE_INTERRUPT and provide a reason
- RTCs with an alarm with a resolution of a minute are now letting
the core handle rounding down the alarm time
- fix use-after-free on device removal
New driver:
- OP-TEE RTC PTA
Drivers:
- sun6i: Add H616 support
- cmos: Fix the AltCentury for AMD platforms
- spear: set range"
* tag 'rtc-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (56 commits)
rtc: check if __rtc_read_time was successful
rtc: gamecube: Fix refcount leak in gamecube_rtc_read_offset_from_sram
rtc: mc146818-lib: Fix the AltCentury for AMD platforms
rtc: optee: add RTC driver for OP-TEE RTC PTA
rtc: pm8xxx: Return -ENODEV if set_time disallowed
rtc: pm8xxx: Attach wake irq to device
clk: sunxi-ng: sun6i-rtc: include clk/sunxi-ng.h
rtc: remove uie_unsupported
rtc: xgene: stop using uie_unsupported
rtc: hym8563: switch to RTC_FEATURE_UPDATE_INTERRUPT
rtc: hym8563: let the core handle the alarm resolution
rtc: hym8563: switch to devm_rtc_allocate_device
rtc: efi: switch to RTC_FEATURE_UPDATE_INTERRUPT
rtc: efi: switch to devm_rtc_allocate_device
rtc: add new RTC_FEATURE_ALARM_WAKEUP_ONLY feature
rtc: spear: fix spear_rtc_read_time
rtc: spear: drop uie_unsupported
rtc: spear: set range
rtc: spear: switch to devm_rtc_allocate_device
rtc: pcf8563: switch to RTC_FEATURE_UPDATE_INTERRUPT
...
Clang static analysis reports this issue
interface.c:810:8: warning: Passed-by-value struct
argument contains uninitialized data
now = rtc_tm_to_ktime(tm);
^~~~~~~~~~~~~~~~~~~
tm is set by a successful call to __rtc_read_time()
but its return status is not checked. Check if
it was successful before setting the enabled flag.
Move the decl of err to function scope.
Fixes: 2b2f5ff00f ("rtc: interface: ignore expired timers when enqueuing new timers")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220326194236.2916310-1-trix@redhat.com
The of_find_compatible_node() function returns a node pointer with
refcount incremented, We should use of_node_put() on it when done
Add the missing of_node_put() to release the refcount.
Fixes: 86559400b3 ("rtc: gamecube: Add a RTC driver for the GameCube, Wii and Wii U")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220309092225.6930-1-linmq006@gmail.com
Setting the century forward has been failing on AMD platforms.
There was a previous attempt at fixing this for family 0x17 as part of
commit 7ad295d519 ("rtc: Fix the AltCentury value on AMD/Hygon
platform") but this was later reverted due to some problems reported
that appeared to stem from an FW bug on a family 0x17 desktop system.
The same comments mentioned in the previous commit continue to apply
to the newer platforms as well.
```
MC146818 driver use function mc146818_set_time() to set register
RTC_FREQ_SELECT(RTC_REG_A)'s bit4-bit6 field which means divider stage
reset value on Intel platform to 0x7.
While AMD/Hygon RTC_REG_A(0Ah)'s bit4 is defined as DV0 [Reference]:
DV0 = 0 selects Bank 0, DV0 = 1 selects Bank 1. Bit5-bit6 is defined
as reserved.
DV0 is set to 1, it will select Bank 1, which will disable AltCentury
register(0x32) access. As UEFI pass acpi_gbl_FADT.century 0x32
(AltCentury), the CMOS write will be failed on code:
CMOS_WRITE(century, acpi_gbl_FADT.century).
Correct RTC_REG_A bank select bit(DV0) to 0 on AMD/Hygon CPUs, it will
enable AltCentury(0x32) register writing and finally setup century as
expected.
```
However in closer examination the change previously submitted was also
modifying bits 5 & 6 which are declared reserved in the AMD documentation.
So instead modify just the DV0 bank selection bit.
Being cognizant that there was a failure reported before, split the code
change out to a static function that can also be used for exclusions if
any regressions such as Mikhail's pop up again.
Cc: Jinke Fan <fanjinke@hygon.cn>
Cc: Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com>
Link: https://lore.kernel.org/all/CABXGCsMLob0DC25JS8wwAYydnDoHBSoMh2_YLPfqm3TTvDE-Zw@mail.gmail.com/
Link: https://www.amd.com/system/files/TechDocs/51192_Bolton_FCH_RRG.pdf
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220111225750.1699-1-mario.limonciello@amd.com
- Add support for Maxim MAX77714 PMIC
- Remove Drivers
- Remove support for ST-Ericsson AB8500 DebugFS
- New Device Support
- Add support for Silergy SY7636A to Simple MFD I2C
- Add support for MediaTek MT6366 PMIC to MT6358 IRQ
- Add support for Charger to Intel PMIC CRC
- Add support for Raptor Lake to Intel LPSS PCI
- New Functionality
- Add support for Reboot to Rockchip RK808
- Fix-ups
- Device Tree changes (inc. YAML conversion); silergy,sy7636a, maxim,max77843,
google,cros-ec, maxim,max14577, maxim,max77802,
maxim,max77714, qcom,tcsr, qcom,spmi-pmic,
stericsson,ab8500, stericsson,db8500-prcmu,
samsung,exynos5433-lpass, mt6397, syscon, brcm,cru
- Visible to menuconfig; simple-mfd-i2c
- Clean-up or clarify code; max77686, intel_soc_pmic_crc
- Improve error handling; mc13xxx-core, stmfx, asic3
- Pass device information to child devices; iqs62x, intel-lpss-acpi
- Individually identify IRQ domains; intel_soc_pmic_core
- Remove superfluous code; dbx500-prcmu, exynos-lpass
- Staticify and constify; arizona-i2c
- Mark sometimes used data as __maybe_unused; atmel-flexcom
- Account for different ACPI tables on AOSP/Windows platforms; arizona-spi
- Use provided (platform) APIs; ab8500-core
- Trivial (whitespace, spelling); rohm-bd9576
-----BEGIN PGP SIGNATURE-----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=1xnI
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Add support for Maxim MAX77714 PMIC
Removed Drivers:
- Remove support for ST-Ericsson AB8500 DebugFS
New Device Support:
- Add support for Silergy SY7636A to Simple MFD I2C
- Add support for MediaTek MT6366 PMIC to MT6358 IRQ
- Add support for Charger to Intel PMIC CRC
- Add support for Raptor Lake to Intel LPSS PCI
New Functionality:
- Add support for Reboot to Rockchip RK808
Fix-ups:
- Device Tree changes (includcing YAML conversion) for
silergy,sy7636a, maxim,max77843, google,cros-ec, maxim,max14577,
maxim,max77802, maxim,max77714, qcom,tcsr, qcom,spmi-pmic,
stericsson,ab8500, stericsson,db8500-prcmu,
samsung,exynos5433-lpass, mt6397, syscon, brcm,cru
- Visible to menuconfig; simple-mfd-i2c
- Clean-up or clarify code; max77686, intel_soc_pmic_crc
- Improve error handling; mc13xxx-core, stmfx, asic3
- Pass device information to child devices; iqs62x, intel-lpss-acpi
- Individually identify IRQ domains; intel_soc_pmic_core
- Remove superfluous code; dbx500-prcmu, exynos-lpass
- Staticify and constify; arizona-i2c
- Mark sometimes used data as __maybe_unused; atmel-flexcom
- Account for different ACPI tables on AOSP/Windows platforms; arizona-spi
- Use provided (platform) APIs; ab8500-core
- Trivial (whitespace, spelling); rohm-bd9576"
* tag 'mfd-next-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (50 commits)
dt-bindings: mfd: syscon: Add microchip,lan966x-cpu-syscon compatible
mfd: bd9576: fix typos in comments
mfd: Use platform_get_irq() to get the interrupt
mfd: db8500-prcmu: Remove unused inline function
mfd: arizona-spi: Add Android board ACPI table handling
mfd: arizona-spi: Split Windows ACPI init code into its own function
mfd: asic3: Add missing iounmap() on error asic3_mfd_probe
MAINTAINERS: Rectify entry for ROHM MULTIFUNCTION BD9571MWV-M PMIC DEVICE DRIVERS
mfd: intel-lpss: Provide an SSP type to the driver
dt-bindings: mfd: brcm,cru: Rename pinctrl node
dt-bindings: Add compatibles for undocumented trivial syscons
mfd: atmel-flexcom: Fix compilation warning
dt-bindings: mfd: Add compatible for the MediaTek MT6366 PMIC
dt-bindings: mfd: samsung,exynos5433-lpass: Convert to dtschema
mfd: exynos-lpass: Drop unneeded syscon.h include
mfd: intel-lpss: Add Intel Raptor Lake PCH-S PCI IDs
mfd: ab8500: Drop debugfs module
mfd: sta2x11: Use GFP_KERNEL instead of GFP_ATOMIC
mfd: ab8500: Rewrite bindings in YAML
mfd: qcom-spmi-pmic: Add pm8953 compatible
...
This drivers allows to communicate with a RTC PTA handled by OP-TEE [1].
This PTA allows to query RTC information, set/get time and set/get
offset depending on the supported features.
[1] https://github.com/OP-TEE/optee_os/pull/5179
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220308133505.471601-1-clement.leger@bootlin.com
Having !allow_set_time is equivalent to non-implemented set_time
function, which is normally represented with -ENODEV error in RTC
subsystem.
Today we are returning -EACCES error code, which is not considered
by RTC clients as a 'non implemented' feature, and which causes NTP
to retry hw clk sync (update_rtc) indefinitely.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/1645090578-20734-1-git-send-email-loic.poulain@linaro.org
Attach the interrupt as a wake-irq to the device, so that:
- A corresponding wakeup source is created (and reported in e.g
/sys/kernel/debug/wakeup_sources).
- The power subsystem take cares of arming/disarming
irq-wake automatically on suspend/resume.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/1645025082-6138-1-git-send-email-loic.poulain@linaro.org
Stop using uie_unsupported and clear RTC_FEATURE_UPDATE_INTERRUPT instead.
Also the driver doesn't supports UIE because it doesn't handle interrupts
so set RTC_FEATURE_ALARM_WAKEUP_ONLY,.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220309162301.61679-24-alexandre.belloni@bootlin.com
The reference manual doesn't specify whether the registers are latched and
they probably aren't, ensure the read time and date are consistent.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/20220309162301.61679-21-alexandre.belloni@bootlin.com
Since commitc9f5c7e7a84f ("rtc: rtc-spear: Provide flag for no support of
UIE mode") which was in 2012, the core changed a lot and UIE are now
supported using regular alarms. Drop uie_unsupported now to reflect that.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/20220309162301.61679-20-alexandre.belloni@bootlin.com
While the RTC can store dates from year 0000 to 9999, leap years where not
tested fro 2100. The driver currently stores tm_year directly which will
probably fail at that time or more probably in 2300.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/20220309162301.61679-19-alexandre.belloni@bootlin.com
No platforms are currently setting no_irq. Anyway, letting platform_get_irq
fail is fine as this means that there is no IRQ. In that case, clear
RTC_FEATURE_ALARM so the core knows there are no alarms.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220309162301.61679-2-alexandre.belloni@bootlin.com
H6 supports IOSC calibration and an ext-osc32k input. Unlike newer SoCs,
it has a single parent for its fanout clock.
Add support for H6 in the CCU driver, replacing the support in the
existing early OF clock provider.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220203021736.13434-7-samuel@sholland.org
The RTC power domain in sun6i and newer SoCs manages the 16 MHz RC
oscillator (called "IOSC" or "osc16M") and the optional 32 kHz crystal
oscillator (called "LOSC" or "osc32k"). Starting with the H6, this power
domain also handles the 24 MHz DCXO (called variously "HOSC", "dcxo24M",
or "osc24M") as well. The H6 also adds a calibration circuit for IOSC.
Later SoCs introduce further variations on the design:
- H616 adds an additional mux for the 32 kHz fanout source.
- R329 adds an additional mux for the RTC timekeeping clock, a clock
for the SPI bus between power domains inside the RTC, and removes the
IOSC calibration functionality.
Take advantage of the CCU framework to handle this increased complexity.
This driver is intended to be a drop-in replacement for the existing RTC
clock provider. So some runtime adjustment of the clock parents is
needed, both to handle hardware differences, and to support the old
binding which omitted some of the input clocks.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220203021736.13434-6-samuel@sholland.org
As the potential failure of the wm8350_register_irq(),
it should be better to check it and return error if fails.
Also, it need not free 'wm_rtc->rtc' since it will be freed
automatically.
Fixes: 077eaf5b40 ("rtc: rtc-wm8350: add support for WM8350 RTC")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220303085030.291793-1-jiasheng@iscas.ac.cn
The H616 RTC changes its day storage to the newly introduced linear day
scheme, so pair the new compatible string with this feature flag.
The RTC clock parts are handled in a separate driver now, so we skip
the clock parts in this driver completely.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220211122643.1343315-7-andre.przywara@arm.com
Newer versions of the Allwinner RTC, for instance as found in the H616
SoC, not only store the current day as a linear number, but also change
the way the alarm is handled: There are now two registers, that
explicitly store the wakeup time, in the same format as the current
time.
Add support for that variant by writing the requested wakeup time
directly into the registers, instead of programming the seconds left, as
the old SoCs required.
Reviewed by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220211122643.1343315-6-andre.przywara@arm.com
Newer versions of the Allwinner RTC, as for instance found in the H616
SoC, no longer store a broken-down day/month/year representation in the
RTC_DAY_REG, but just a linear day number.
The user manual does not give any indication about the expected epoch
time of this day count, but the BSP kernel uses the UNIX epoch, which
allows easy support due to existing conversion functions in the kernel.
Allow tagging a compatible string with a flag, and use that to mark
those new RTCs. Then convert between a UNIX day number (converted into
seconds) and the broken-down day representation using mktime64() and
time64_to_tm() in the set_time/get_time functions.
That enables support for the RTC in those new chips.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220211122643.1343315-5-andre.przywara@arm.com
Using "unsigned long" for UNIX timestamps is never a good idea, and
comparing the value of such a variable against U32_MAX does not do
anything useful on 32-bit systems.
Use the proper time64_t type when dealing with timestamps, and avoid
cutting down the time range unnecessarily. This also fixes the flawed
check for the alarm time being too far into the future.
The check for this condition is actually somewhat theoretical, as the
RTC counts till 2033 only anyways, and 2^32 seconds from now is not
before the year 2157 - at which point I hope nobody will be using this
hardware anymore.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220211122643.1343315-4-andre.przywara@arm.com
When there is no interrupt line, rtc alarm feature is disabled.
The clearing of the alarm feature bit was being done prior to allocations
of ldata->rtc device, resulting in a null pointer dereference.
Clear RTC_FEATURE_ALARM after the rtc device is allocated.
Fixes: d9b0dd54a1 ("rtc: pl031: use RTC_FEATURE_ALARM")
Cc: stable@vger.kernel.org
Signed-off-by: Ali Pouladi <quic_apouladi@quicinc.com>
Signed-off-by: Elliot Berman <quic_eberman@quicinc.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220225161924.274141-1-quic_eberman@quicinc.com
In mc146818_set_time(), CMOS_READ(RTC_CONTROL) was performed without the
rtc_lock taken, which is required for CMOS accesses. Fix this.
Nothing in kernel modifies RTC_DM_BINARY, so a separate critical section
is allowed here.
Fixes: dcf257e926 ("rtc: mc146818: Reduce spinlock section in mc146818_set_time()")
Signed-off-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220220090403.153928-1-mat.jonczyk@o2.pl
The RTC included in the MAX77714 PMIC is very similar to the one in the
MAX77686. Reuse the rtc-max77686.c driver with the minimum required changes
for the MAX77714 RTC.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The MAX77714 RTC chip is explicitly set to 24-hour mode in
max77686_rtc_probe() -> max77686_rtc_init_reg() and never changed back to
12-hour mode. Accordingly info->rtc_24hr_mode is set to 1 in the same place
and never modified later, so it is de facto a constant. Yet there is code
to read 12-hour time, which is unreachable.
Remove the unused variable, the unreachable code to manage 12-hour mode and
the defines that become unused due to the above changes.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
RTC_DATE and REG_RTC_DATE are used for the registers holding the day of
month. Rename these constants to mean what they mean.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Convert the comments documenting this struct to kernel-doc format for
standardization and readability.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The first bug is that reading the 5 alarm registers results in a read
operation of 20 bytes. The reason is because the destination buffer is
defined as an array of "unsigned int", and we use the sizeof()
operator on this array to define the bulk read count.
The second bug is that the read value is invalid, because we are
indexing the destination buffer as integers (4 bytes), instead of
indexing it as u8.
Changing the destination buffer type to u8 fixes both problems.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220208162908.3182581-1-hugo@hugovil.com
If the interrupt pin of the PCF2127 is routed to the input of a GPIO
expander using the pca953x driver, the later will only accept an IRQ
of type IRQ_TYPE_EDGE_FALLING or IRQ_TYPE_EDGE_RISING, and the IRQ
request will fail.
Therefore, allow the IRQ type to be passed from the device tree data
if available.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220117225742.1252362-1-hugo@hugovil.com
When building with automatic stack variable initialization, GCC 12
complains about variables defined outside of switch case statements.
Move variables outside the switch, which silences warnings:
./drivers/rtc/rtc-pcf8523.c:284:20: error: statement will never be executed [-Werror=switch-unreachable]
284 | u8 mode;
|
./drivers/rtc/rtc-pcf8523.c:245:21: error: statement will never be executed [-Werror=switch-unreachable]
245 | u32 value;
| ^~~~~
Signed-off-by: Victor Erminpour <victor.erminpour@oracle.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/1644453027-886-1-git-send-email-victor.erminpour@oracle.com
H6 and newer variants of the RTC hardware have a bus clock gate in the
PRCM CCU. This was not known at the time H6 support was added, so it was
not included in the H6 RTC binding, nor in the H6 PRCM CCU driver. Now
that this clock gate is documented, it is included in the A100 and D1
PRCM CCU drivers. Therefore, the RTC driver needs to have a consumer for
the clock gate to prevent Linux from disabling it.
Patch-changes: 3
- New patch for compatibility with new CCU drivers
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220203021736.13434-4-samuel@sholland.org
If the irqwork is still scheduled or running while the RTC device is
removed, a use-after-free occurs in rtc_timer_do_work(). Cleanup the
timerqueue and ensure the work is stopped to fix this.
BUG: KASAN: use-after-free in mutex_lock+0x94/0x110
Write of size 8 at addr ffffff801d846338 by task kworker/3:1/41
Workqueue: events rtc_timer_do_work
Call trace:
mutex_lock+0x94/0x110
rtc_timer_do_work+0xec/0x630
process_one_work+0x5fc/0x1344
...
Allocated by task 551:
kmem_cache_alloc_trace+0x384/0x6e0
devm_rtc_allocate_device+0xf0/0x574
devm_rtc_device_register+0x2c/0x12c
...
Freed by task 572:
kfree+0x114/0x4d0
rtc_device_release+0x64/0x80
device_release+0x8c/0x1f4
kobject_put+0x1c4/0x4b0
put_device+0x20/0x30
devm_rtc_release_device+0x1c/0x30
devm_action_release+0x54/0x90
release_nodes+0x124/0x310
devres_release_group+0x170/0x240
i2c_device_remove+0xd8/0x314
...
Last potentially related work creation:
insert_work+0x5c/0x330
queue_work_on+0xcc/0x154
rtc_set_time+0x188/0x5bc
rtc_dev_ioctl+0x2ac/0xbd0
...
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211210160951.7718-1-vincent.whitchurch@axis.com
The value returned by an spi driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)
So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Claudius Heine <ch@denx.de>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Acked-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Acked-by: Łukasz Stelmach <l.stelmach@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220123175201.34839-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
If devm_ioremap_resource() fails, it should return error
code from sp_rtc->reg_base in sp_rtc_probe().
Fixes: fad6cbe9b2 ("rtc: Add driver for RTC in Sunplus SP7021")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220106075711.3216468-1-yangyingliang@huawei.com
There's limiting the year to 2069. When setting the rtc year to 2070,
reading it returns 1970. Evaluate century starting from 19 to count the
correct year.
$ sudo date -s 20700106
Mon 06 Jan 2070 12:00:00 AM CST
$ sudo hwclock -w
$ sudo hwclock -r
1970-01-06 12:00:49.604968+08:00
Fixes: 2a4daadd4d ("rtc: cmos: ignore bogus century byte")
Signed-off-by: Riwen Lu <luriwen@kylinos.cn>
Acked-by: Eric Wong <e@80x24.org>
Reviewed-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220106084609.1223688-1-luriwen@kylinos.cn
The devm_kzalloc() function returns NULL on error, it doesn't return
error pointers.
Fixes: 86559400b3 ("rtc: gamecube: Add a RTC driver for the GameCube, Wii and Wii U")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Emmanuel Gil Peyrot <linkmauve@linkmauve.fr>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220107073340.GF22086@kili
The mc146818_get_time() function returns zero on success or negative
a error code on failure. It needs to be type int.
Fixes: d35786b3a2 ("rtc: mc146818-lib: change return values of mc146818_get_time()")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220111071922.GE11243@kili
With the latest stable kernel versions the rtc on the PXA based
Zaurus does not work, when booting I see the following kernel messages:
pxa-rtc pxa-rtc: failed to find rtc clock source
pxa-rtc pxa-rtc: Unable to init SA1100 RTC sub-device
pxa-rtc: probe of pxa-rtc failed with error -2
hctosys: unable to open rtc device (rtc0)
I think this is because commit f2997775b1 ("rtc: sa1100: fix possible
race condition") moved the allocation of the rtc_device struct out of
sa1100_rtc_init and into sa1100_rtc_probe. This means that pxa_rtc_probe
also needs to do allocation for the rtc_device struct, otherwise
sa1100_rtc_init will try to dereference a null pointer. This patch adds
that allocation by copying how sa1100_rtc_probe in
drivers/rtc/rtc-sa1100.c does it; after the IRQs are set up a managed
rtc_device is allocated.
I've tested this patch with `qemu-system-arm -machine akita` and with a
real Zaurus SL-C1000 applied to 4.19, 5.4, and 5.10.
Signed-off-by: Laurence de Bruxelles <lfdebrux@gmail.com>
Fixes: f2997775b1 ("rtc: sa1100: fix possible race condition")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220101154149.12026-1-lfdebrux@gmail.com
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211220011524.17206-1-prabhakar.mahadev-lad.rj@bp.renesas.com
When building with automatic stack variable initialization, GCC 12
complains about variables defined outside of switch case statements.
Move the variable into the case that uses it, which silences the warning:
drivers/rtc/dev.c: In function 'rtc_dev_ioctl':
drivers/rtc/dev.c:394:30: warning: statement will never be executed [-Wswitch-unreachable]
394 | long offset;
| ^~~~~~
Fixes: 6a8af1b656 ("rtc: add parameter ioctl")
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211209043915.1378393-1-keescook@chromium.org
The XSL bit only exists in RS5C372A/B. On other Ricoh RTC chips
supported in rs5c372, this bit has different meaning. For example, on
R2221x and R2223x, this bit of oscillation adjustment register
determines the operation frequency of oscillation adjustment circuit and
the oscillation is always 32768HZ. But rs5c372_get_trim gives 32000HZ to
osc when DEV is 1.
Signed-off-by: Camel Guo <camelg@axis.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211206125832.6461-1-camel.guo@axis.com
In order for linux userspace application to be able to adjust offset to
keep rtc precision as high as possible, this commit adds support of
offset correction by adjusting the time trimming register on
rs5c372[a|b] and oscilluation adjustment register on r2025x, r222[1|3]x,
rv5c38[6|7]a.
Signed-off-by: Camel Guo <camelg@axis.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211202152252.31264-1-camel.guo@axis.com
Some Intel chipsets disconnect the time and date RTC registers when the
clock update is in progress: during this time reads may return bogus
values and writes fail silently. This includes the RTC alarm registers.
[1]
cmos_set_alarm() did not take account for that, fix it.
[1] 7th Generation Intel ® Processor Family I/O for U/Y Platforms [...]
Datasheet, Volume 1 of 2 (Intel's Document Number: 334658-006)
Page 208
https://www.intel.com/content/dam/www/public/us/en/documents/datasheets/7th-and-8th-gen-core-family-mobile-u-y-processor-lines-i-o-datasheet-vol-1.pdf
"If a RAM read from the ten time and date bytes is attempted
during an update cycle, the value read do not necessarily
represent the true contents of those locations. Any RAM writes
under the same conditions are ignored."
Signed-off-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211210200131.153887-10-mat.jonczyk@o2.pl
Some Intel chipsets disconnect the time and date RTC registers when the
clock update is in progress: during this time reads may return bogus
values and writes fail silently. This includes the RTC alarm registers.
[1]
cmos_read_alarm() did not take account for that, which caused alarm time
reads to sometimes return bogus values. This can be shown with a test
patch that I am attaching to this patch series.
Fix this, by using mc146818_avoid_UIP().
[1] 7th Generation Intel ® Processor Family I/O for U/Y Platforms [...]
Datasheet, Volume 1 of 2 (Intel's Document Number: 334658-006)
Page 208
https://www.intel.com/content/dam/www/public/us/en/documents/datasheets/7th-and-8th-gen-core-family-mobile-u-y-processor-lines-i-o-datasheet-vol-1.pdf
"If a RAM read from the ten time and date bytes is attempted
during an update cycle, the value read do not necessarily
represent the true contents of those locations. Any RAM writes
under the same conditions are ignored."
Signed-off-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211210200131.153887-9-mat.jonczyk@o2.pl
Refactor mc146818_does_rtc_work() so that it uses mc146818_avoid_UIP().
It is enough to call mc146818_avoid_UIP() with no callback.
Signed-off-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211210200131.153887-8-mat.jonczyk@o2.pl
Function mc146818_get_time() contains an elaborate mechanism of reading
the RTC time while no RTC update is in progress. It turns out that
reading the RTC alarm clock also requires avoiding the RTC update.
Therefore, the mechanism in mc146818_get_time() should be reused - so
extract it into a separate function.
The logic in mc146818_avoid_UIP() is same as in mc146818_get_time()
except that after every
if (CMOS_READ(RTC_FREQ_SELECT) & RTC_UIP) {
there is now "mdelay(1)".
To avoid producing a very unreadable patch, mc146818_get_time() will be
refactored to use mc146818_avoid_UIP() in the next patch.
Signed-off-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211210200131.153887-6-mat.jonczyk@o2.pl
To prevent an infinite loop in mc146818_get_time(),
commit 211e5db19d ("rtc: mc146818: Detect and handle broken RTCs")
added a check for RTC availability. Together with a later fix, it
checked if bit 6 in register 0x0d is cleared.
This, however, caused a false negative on a motherboard with an AMD
SB710 southbridge; according to the specification [1], bit 6 of register
0x0d of this chipset is a scratchbit. This caused a regression in Linux
5.11 - the RTC was determined broken by the kernel and not used by
rtc-cmos.c [3]. This problem was also reported in Fedora [4].
As a better alternative, check whether the UIP ("Update-in-progress")
bit is set for longer then 10ms. If that is the case, then apparently
the RTC is either absent (and all register reads return 0xff) or broken.
Also limit the number of loop iterations in mc146818_get_time() to 10 to
prevent an infinite loop there.
The functions mc146818_get_time() and mc146818_does_rtc_work() will be
refactored later in this patch series, in order to fix a separate
problem with reading / setting the RTC alarm time. This is done so to
avoid a confusion about what is being fixed when.
In a previous approach to this problem, I implemented a check whether
the RTC_HOURS register contains a value <= 24. This, however, sometimes
did not work correctly on my Intel Kaby Lake laptop. According to
Intel's documentation [2], "the time and date RAM locations (0-9) are
disconnected from the external bus" during the update cycle so reading
this register without checking the UIP bit is incorrect.
[1] AMD SB700/710/750 Register Reference Guide, page 308,
https://developer.amd.com/wordpress/media/2012/10/43009_sb7xx_rrg_pub_1.00.pdf
[2] 7th Generation Intel ® Processor Family I/O for U/Y Platforms [...] Datasheet
Volume 1 of 2, page 209
Intel's Document Number: 334658-006,
https://www.intel.com/content/dam/www/public/us/en/documents/datasheets/7th-and-8th-gen-core-family-mobile-u-y-processor-lines-i-o-datasheet-vol-1.pdf
[3] Functions in arch/x86/kernel/rtc.c apparently were using it.
[4] https://bugzilla.redhat.com/show_bug.cgi?id=1936688
Fixes: 211e5db19d ("rtc: mc146818: Detect and handle broken RTCs")
Fixes: ebb22a0594 ("rtc: mc146818: Dont test for bit 0-5 in Register D")
Signed-off-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211210200131.153887-5-mat.jonczyk@o2.pl
There are 4 users of mc146818_get_time() and none of them was checking
the return value from this function. Change this.
Print the appropriate warnings in callers of mc146818_get_time() instead
of in the function mc146818_get_time() itself, in order not to add
strings to rtc-mc146818-lib.c, which is kind of a library.
The callers of alpha_rtc_read_time() and cmos_read_time() may use the
contents of (struct rtc_time *) even when the functions return a failure
code. Therefore, set the contents of (struct rtc_time *) to 0x00,
which looks more sensible then 0xff and aligns with the (possibly
stale?) comment in cmos_read_time:
/*
* If pm_trace abused the RTC for storage, set the timespec to 0,
* which tells the caller that this RTC value is unusable.
*/
For consistency, do this in mc146818_get_time().
Note: hpet_rtc_interrupt() may call mc146818_get_time() many times a
second. It is very unlikely, though, that the RTC suddenly stops
working and mc146818_get_time() would consistently fail.
Only compile-tested on alpha.
Signed-off-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: linux-alpha@vger.kernel.org
Cc: x86@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211210200131.153887-4-mat.jonczyk@o2.pl
No function is checking mc146818_get_time() return values yet, so
correct them to make them more customary.
Signed-off-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211210200131.153887-3-mat.jonczyk@o2.pl
Reading from the CMOS involves writing to the index register and then
reading from the data register. Therefore access to the CMOS has to be
serialized with rtc_lock. This invocation of CMOS_READ was not
serialized, which could cause trouble when other code is accessing CMOS
at the same time.
Use spin_lock_irq() like the rest of the function.
Nothing in kernel modifies the RTC_DM_BINARY bit, so there could be a
separate pair of spin_lock_irq() / spin_unlock_irq() before doing the
math.
Signed-off-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Reviewed-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211210200131.153887-2-mat.jonczyk@o2.pl
I haven’t been able to test this patch as all of my consoles have a
working RTC battery, but according to the documentation it should work
like that.
Signed-off-by: Emmanuel Gil Peyrot <linkmauve@linkmauve.fr>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211215175501.6761-3-linkmauve@linkmauve.fr
These three consoles share a device, the MX23L4005, which contains a
clock and 64 bytes of SRAM storage, and is exposed on the EXI bus
(similar to SPI) on channel 0, device 1. This driver allows it to be
used as a Linux RTC device, where time can be read and set.
The hardware also exposes two timers, one which shuts down the console
and one which powers it on, but these aren’t supported currently.
On the Wii U, the counter bias is stored in a XML file, /config/rtc.xml,
encrypted in the SLC (eMMC storage), using a proprietary filesystem. In
order to avoid having to implement all that, this driver assumes a
bootloader will parse this XML file and write the bias into the SRAM, at
the same location the other two consoles have it.
Signed-off-by: Emmanuel Gil Peyrot <linkmauve@linkmauve.fr>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211215175501.6761-2-linkmauve@linkmauve.fr
The Epson RX8804 RTC has the same programming model as RV8803.
Add support for it in the driver.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211130125830.1166194-2-festevam@gmail.com
As da9063 RTC is not a real I2C client, but relies on da9063 MFD
driver, we need to explicitly mark da9063 RTC as a wakeup source
to be able to access class/rtc/rtcN/wakealarm sysfs entry
to set alarms, so we can wakeup from SHUTDOWN/RTC/DELIVERY mode.
As da9063 driver refuses to load without irq, we simply add it
as a wakeup source before registering rtc device.
Signed-off-by: Nikita Shubin <nikita.shubin@maquefel.me>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211129072650.22686-1-nikita.shubin@maquefel.me
Stop using uie_unsupported and clear RTC_FEATURE_UPDATE_INTERRUPT instead.
Also, let the core know that the alarm will truncate seconds as it only has
a minute resolution.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Link: https://lore.kernel.org/r/20211109234750.107115-1-alexandre.belloni@bootlin.com
The pcf85063 driver regsitration currently supports the "compatible"
property type of matching (for DT).
This patch adds "matching by name" support to the driver by defining
an i2c_device_id table and setting the id_table parameter in the
i2c_driver struct.
This will, for example, make the driver easier to instantiate on
systems where CONFIG_OF is not enabled (x86 in my case).
Signed-off-by: Marc Ferland <ferlandm@amotus.ca>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211116164733.17149-1-ferlandm@amotus.ca
In order to make it possible to get battery voltage status, this commit
adds RTC_VL_READ, RTC_VL_CLR ioctl commands to rtc-rs5c372.
Signed-off-by: Camel Guo <camelg@axis.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211111083625.10216-1-camel.guo@axis.com
Subsystem:
- Add new ioctl to get and set extra RTC parameters, this includes backup
switch mode
- Expose available features to userspace, in particular, when alarmas have a
resolution of one minute instead of a second.
- Let the core handle those alarms with a minute resolution
New driver:
- MSTAR MSC313 RTC
Drivers:
- Add SPI ID table where necessary
- Add BSM support for rv3028, rv3032 and pcf8523
- s3c: set RTC range
- rx8025: set range, implement .set_offset and .read_offset
-----BEGIN PGP SIGNATURE-----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=pTlj
-----END PGP SIGNATURE-----
Merge tag 'rtc-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"This includes new ioctls to get and set parameters and in particular
the backup switch mode that is needed for some RTCs to actually enable
the backup voltage (and have a useful RTC).
The same interface can also be used to get the actual features
supported by the RTC so userspace has a better way than trying and
failing.
Summary:
Subsystem:
- Add new ioctl to get and set extra RTC parameters, this includes
backup switch mode
- Expose available features to userspace, in particular, when alarmas
have a resolution of one minute instead of a second.
- Let the core handle those alarms with a minute resolution
New driver:
- MSTAR MSC313 RTC
Drivers:
- Add SPI ID table where necessary
- Add BSM support for rv3028, rv3032 and pcf8523
- s3c: set RTC range
- rx8025: set range, implement .set_offset and .read_offset"
* tag 'rtc-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (50 commits)
rtc: rx8025: use .set_offset/.read_offset
rtc: rx8025: use rtc_add_group
rtc: rx8025: clear RTC_FEATURE_ALARM when alarm are not supported
rtc: rx8025: set range
rtc: rx8025: let the core handle the alarm resolution
rtc: rx8025: switch to devm_rtc_allocate_device
rtc: ab8500: let the core handle the alarm resolution
rtc: ab-eoz9: support UIE when available
rtc: ab-eoz9: use RTC_FEATURE_UPDATE_INTERRUPT
rtc: rv3032: let the core handle the alarm resolution
rtc: s35390a: let the core handle the alarm resolution
rtc: handle alarms with a minute resolution
rtc: pcf85063: silence cppcheck warning
rtc: rv8803: fix writing back ctrl in flag register
rtc: s3c: Add time range
rtc: s3c: Extract read/write IO into separate functions
rtc: s3c: Remove usage of devm_rtc_device_register()
rtc: tps80031: Remove driver
rtc: sun6i: Allow probing without an early clock provider
rtc: pcf8523: add BSM support
...
The driver has its own sysfs file to adjust the clock. Fortunately, it is
already in pbb, however, the sign it expects is the opposite of what the
RTC core does (which actually aligns with the RTC).
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211107225458.111068-12-alexandre.belloni@bootlin.com
Tell the RTC core UIE are not supported because the resolution of the alarm
is a minute.
Note that this is in fact also fixing how the resolution is reported as the
previous test was simply ensuring the alarm was more than a minute in the
future while the register has a minute resolution.
This would be ok if the alarm was a countdown but ab8500_rtc_read_alarm
suggests otherwise and the AB8500 datasheet states that the RTC
documentation is not public.
Finally, the comment is wrong and what makes the UIE emulation work is
uie_unsupported being set.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20211107225458.111068-6-alexandre.belloni@bootlin.com
Handle alarms with a minute resolution in the core. Until now drivers have
been open coding the seconds part removal and have been doing that wrongly.
Most of them are rounding up which means the allow the system to miss
deadlines. So, round down and let __rtc_set_alarm return immediately if the
time has already passed.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211107225458.111068-1-alexandre.belloni@bootlin.com
ctrl is set from read_regs(..FLAG, 2, ctrl), so ctrl[0] is FLAG
and ctrl[1] is the CTRL register.
Use ctrl[0] to write back to the FLAG register as appropriate.
Signed-off-by: Dominique Martinet <dominique.martinet@atmark-techno.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211101013400.325855-1-dominique.martinet@atmark-techno.com
1. Convert Exynos ChipID and ASV driver to a module and make it a
default, instead of selected. The driver is not essential, so it
could be disabled, if needed.
2. Add support for Exynos850 and Exynos Auto v9 to Exynos ChipID and ASV
driver.
3. Get rid of HAVE_S3C_RTC because it was adding just another layer
instead of direct dependencies.
4. Minor cleanups.
-----BEGIN PGP SIGNATURE-----
iQJEBAABCgAuFiEE3dJiKD0RGyM7briowTdm5oaLg9cFAmF3zFcQHGtyemtAa2Vy
bmVsLm9yZwAKCRDBN2bmhouD1wXED/9VSIwfegbhUkfa9yCetdt8dDrjINAUuZ89
FZsplj7BdFJVra7KxjZ6WSWqT5bBVF804mPQKi/filUvuZLr8oOVc/BCdARPMqxq
3rui2xiXvUgDWfJmqFEaVhTTChKAK2NKMgC+aGB0Ah3PK9QbO9fG+E1IcOBLIEUQ
bQH77+GH4rG8/INWdrqmL7LrJUkOyUsCgK3IxGh08m6nRgn8Xfwk1Y0UPpeGgQTs
66CnmIgBiN3+w0MeFClHpLXokBnSSFwrtITrwLILffAO18EEFaaErSZhSyge4tdu
WwH9no+mcp8gpV7mU/b4rAhNVqn6LIldGrk3O6H9Pm9RJj1ITsLYdTXEpUKErXma
g3ZloSyQ/zMUAM3K6rMHYg92Z8pUTnbkbYI6hoCgPGmrHIIRIhIjbjafBHuFZuhL
aeLUCcPxGv3tETjmDaSscHDJ+kVtCyArAoggDbPzWr8V7IO8OmMecxTfYJEKPelM
CH0uvIBHgXRtSF091XbrJ8vXy/GZSWZJH5CrQmeY/HqE+iJFAYXGj53fohGlOu7m
t0OsCnnX/eaCRFPtg6yUfGbiJ3xjdyTvA6ffn7c4Eel4tezy3HnGIaIjA/QI2KVa
J18YWZDMGxeQpofuTo8wpCZiUZo/6zlVb3zh9vyRvf1gR06Ln8y5Kb+SAna+EvTj
YDxiCGYwIg==
=ZJb8
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEo6/YBQwIrVS28WGKmmx57+YAGNkFAmF4G7MACgkQmmx57+YA
GNk7ug//Y69NRwLTxnZSY5mX88SegROm4oARW8+hZLA3XGmpZuZsNBzc709p/64B
Ba/AKIILWKzY4kp5gdT+u02JYoPNVYGuq0SQ1F/Owj7ojAQkBKpwlvDARCIWIFN0
4HohEU6eO1XOm3aUqKYsGfZxk53ECnx3IP5vxSVkTUGOSQKNQAsqIKG+bfYM3J/4
AsMFwm7aMHxgBqAxk3ZTPeqAl2JLH5+7uIcZHRWqt9wCiPMWXLSVbKpW79xPHCHC
eaRw6je+HI4MwZjNSqdmaiP/4WCnKGowiq0OGnkv9vcH4GykT9a6qS3pTL50rLom
lHov9WbNXGP+wFYMWLn9f8fyLwFmdNmOFvkQT6IX2H4a6VlceMqx6HfAKzeAr6fX
6ck6/t8gjF/s9rXpR08sBDpefXLxp7nYZSsFMNesVRCD+h+JciC3pnUw+YgUpcRb
GK4AoaxHbaIJy94OzARGECOP7fzXfVFBrMHgYucWOeVvX1W7JX0eyDKOAkWF4W+J
R+af/7HIcNtB1bXFpxL6Njeyyf2B4a8qncMlLTtJ7r5DX5oU7T8KRngzD4kCvnkP
gjkBzY1+41/K9RCII6L05miNc36ATf/07bQx4e1F2L9/1RzGnjIl8OxN5OVs89y0
CvplsgtlYgnGccNbpChO0r4IaR7UWYTDPulXkEdNE+jJxuTYvwI=
=y2Ab
-----END PGP SIGNATURE-----
Merge tag 'samsung-drivers-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/drivers
Samsung SoC drivers changes for v5.16
1. Convert Exynos ChipID and ASV driver to a module and make it a
default, instead of selected. The driver is not essential, so it
could be disabled, if needed.
2. Add support for Exynos850 and Exynos Auto v9 to Exynos ChipID and ASV
driver.
3. Get rid of HAVE_S3C_RTC because it was adding just another layer
instead of direct dependencies.
4. Minor cleanups.
* tag 'samsung-drivers-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
soc: samsung: exynos-chipid: add exynosautov9 SoC support
rtc: s3c: remove HAVE_S3C_RTC in favor of direct dependencies
soc: samsung: exynos-chipid: Add Exynos850 support
dt-bindings: samsung: exynos-chipid: Document Exynos850 compatible
soc: samsung: exynos-chipid: Pass revision reg offsets
soc: samsung: pm_domains: drop unused is_off field
arm64: exynos: don't have ARCH_EXYNOS select EXYNOS_CHIPID
soc: samsung: exynos-chipid: do not enforce built-in
soc: samsung: exynos-chipid: convert to a module
soc: samsung: exynos-chipid: avoid soc_device_to_device()
soc: samsung: exynos-pmu: Fix compilation when nothing selects CONFIG_MFD_CORE
Link: https://lore.kernel.org/r/20211026094709.75692-2-krzysztof.kozlowski@canonical.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This RTC driver starts counting from 2000 to avoid Y2K problem. Also it
only supports 100 years range for all RTCs. Provide that info to RTC
framework. Also remove check for 100 years range in s3c_rtc_settime(),
as RTC core won't pass any invalid values to the driver, now that
correct range is set.
Here is the rationale on 100 years range limitation. Info on different
Samsung RTCs (credit goes to Krzysztof Kozlowski):
- All S3C chips have only 8-bit wide year register (can store 100
years range in BCD format)
- S5Pv210 and Exynos chips have 12-bit year register (can store 1000
years range in BCD format)
But in reality we usually can't make use of those 12 bits either:
- RTCs might think that both 2000 and 2100 years are leap years. So
when the YEAR register is 0, RTC goes from 28 Feb to 29 Feb, and
when the YEAR register is 100, RTC also goes from 28 Feb to 29 Feb.
This is of course incorrect: RTC breaks leap year criteria, which
breaks the time contiguity, which leads to inability to use the RTC
after year of 2099. It was found for example on Exynos850 SoC.
- Despite having 12 bits for holding the year value, RTC might
overflow the year value internally much earlier. For example, on
Exynos850 the RTC overflows when YEAR=159, making the next YEAR=0.
This way RTC actually has range of 160 years, not 1000 as one may
think.
All that said, there is no sense in trying to increase the time range
for more than 100 years on RTCs that seem capable of that. It also
doesn't have too much practical value -- current hardware will be
probably obsolete by 2100.
Tested manually on Exynos850 RTC:
$ date -s "1999-12-31 23:59:50"
$ hwclock -w -f /dev/rtc0
$ date -s "2100-01-01 00:00:00"
$ hwclock -w -f /dev/rtc0
$ date -s "2000-01-01 00:00:00"
$ hwclock -w -f /dev/rtc0
$ hwclock -r -f /dev/rtc0
$ date -s "2099-12-31 23:59:50"
$ hwclock -w -f /dev/rtc0
$ hwclock -r -f /dev/rtc0
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211021202256.28517-4-semen.protsenko@linaro.org
Create dedicated functions for I/O operations and BCD conversion. It can
be useful to separate those from representation conversion and other
stuff found in RTC callbacks.
This patch does not introduce any functional changes, it's merely
refactoring change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211021202256.28517-3-semen.protsenko@linaro.org
devm_rtc_device_register() is deprecated. Use devm_rtc_allocate_device()
and devm_rtc_register_device() API instead. This change doesn't change
the behavior, but allows for further improvements.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211021202256.28517-2-semen.protsenko@linaro.org
Some SoCs have an RTC supported by this RTC driver, but do not have an
early clock provider declared here. Currently, this prevents the RTC
driver from probing, because it expects a global struct to already be
allocated. Fix probing the driver by copying the missing pieces from the
clock provider setup function, replacing them with the devm variants.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210928080335.36706-7-samuel@sholland.org
Backup Switch Mode allows to select the strategy to use to switch from the
main power supply to the backup power supply. As before, the driver will
switch from standby mode to level mode but now only when it has never been
set.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211018153651.82069-5-alexandre.belloni@bootlin.com
Compiling out pcf8523_rtc_ioctl saves about 5% of the generated machine
code. However, it certainly never happens as the RTC character device
interface is the most useful one and is probably always compiled in.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211018153651.82069-2-alexandre.belloni@bootlin.com
Use regmap to access the RTC registers, this is a huge reduction in code
lines and generated code. Values on ARMv7:
text data bss dec hex
5180 132 0 5312 14c0 before
3900 132 0 4032 fc0 after
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211018153651.82069-1-alexandre.belloni@bootlin.com
BLF, battery low doesn't mean the time is imprecise or invalid, it simply mean
the backup battery has to be replaced. This information can be read using the
VL_READ ioctl.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211015192400.818254-1-alexandre.belloni@bootlin.com
Backup Switch Mode is currently set properly when the trickle charger is
enabled. However, in the case of a non-rechargeable battery, it is
necessary to be able to enable it, only allow that when the trickle charger
is disabled.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211018151933.76865-8-alexandre.belloni@bootlin.com
Backup Switch Mode controls how the RTC decides when to switch to the
backup power supply. As it is disabled by default, provide a way to enable
and configure it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211018151933.76865-7-alexandre.belloni@bootlin.com
BSM or Backup Switch Mode is a common feature on RTCs, allowing to select
how the RTC will decide when to switch from its primary power supply to the
backup power supply. It is necessary to be able to set it from userspace as
there are uses cases where it has to be done dynamically.
Supported values are:
RTC_BSM_DISABLED: disabled
RTC_BSM_DIRECT: switching will happen as soon as Vbackup > Vdd
RTC_BSM_LEVEL: switching will happen around a threshold, usually with an
hysteresis
RTC_BSM_STANDBY: switching will not happen until Vdd > Vbackup, this is
useful to ensure the RTC doesn't draw any power until the device is first
powered on.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211018151933.76865-6-alexandre.belloni@bootlin.com
Add a new feature for RTCs able to correct the oscillator imprecision. This
is also called offset or trimming. Such drivers have a .set_offset callback,
use that to set the feature bit from the core.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211018151933.76865-4-alexandre.belloni@bootlin.com
The config HAVE_S3C_RTC is not really needed since we can simply just
add the dependencies directly to RTC_DRV_S3C. Also, one less config to
keep track of!
Signed-off-by: Will McVicker <willmcvicker@google.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211013212256.3425889-1-willmcvicker@google.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Power-on reset after the insertion of a battery does not always complete
successfully, leading to corrupted register content. The EXT_TEST bit
will stop the clock from running, but currently the driver will never
recover.
Safely handle the erroneous state by clearing EXT_TEST as part of the
usual set_time method.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211015111208.1757110-1-phil@raspberrypi.com
TQ-Systems' TQMa8Mx module (SoM) uses a pcf85063 as RTC. The default output
is 32768Hz. This is to provide the i.MX8M CKIL clock. Once the RTC driver
is probed, the clock is disabled and all i.MX8M functionality depending on
the 32 KHz clock will halt. In our case the whole system halts and a power
cycle is required.
Referencing the pcf85063 directly results in a deadlock. The kernel
will see, that i.MX8M system clock needs the RTC clock and do probe
deferral. But the i.MX8M I2C module never becomes usable without the
i.MX8M CKIL clock and thus the RTC's clock will not be probed. So
from the kernel's perspective this is a chicken-and-egg problem.
Technically everything is fine by not touching anything, since
the RTC clock correctly enables the clock on reset (i.e. on
battery backup power loss).
A workaround for this issue is describing the square wave pin
as fixed-clock, which is registered early and basically how
this pin is used on the i.MX8M.
This addresses the exact same issue as in commit f765e349c3 ("rtc:
m41t80: add support for fixed clock").
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
[Fixed return value 0 -> NULL]
Link: https://lore.kernel.org/r/20211013074954.997445-1-alexander.stein@ew.tq-group.com
Do not call rv3032_exit_eerd() if the enter function fails but don't
forget to call the exit when the enter succeeds.
Fixes: 2eeaa532ac ("rtc: rv3032: Add a driver for Microcrystal RV-3032")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211012101028.GT2083@kadam
I got a null-ptr-deref report when doing fault injection test:
BUG: kernel NULL pointer dereference, address: 0000000000000000
RIP: 0010:strcmp+0xc/0x20
Call Trace:
__devm_rtc_register_device.cold.7+0x16a/0x2df
rv3029_probe+0x4b1/0x770 [rtc_rv3029c2]
rv3029_i2c_probe+0x141/0x180 [rtc_rv3029c2]
i2c_device_probe+0xa07/0xbb0
really_probe+0x285/0xc30
If dev_set_name() fails, dev_name() is null, it causes null-ptr-deref,
we need check the return value of dev_set_name().
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211012041629.2504158-1-yangyingliang@huawei.com
I got a null-ptr-deref report when doing fault injection test:
general protection fault, probably for non-canonical address 0xdffffc0000000022: 0000 [#1] SMP KASAN PTI
KASAN: null-ptr-deref in range [0x0000000000000110-0x0000000000000117]
RIP: 0010:device_del+0x132/0xdc0
Call Trace:
cdev_device_del+0x1a/0x80
devm_rtc_unregister_device+0x37/0x80
release_nodes+0xc3/0x3b0
If cdev_device_add() fails, 'dev->p' is not set, it causes
null-ptr-deref when calling cdev_device_del(). Registering
character device is optional, we don't return error code
here, so introduce a new flag 'RTC_NO_CDEV' to indicate
if it has character device, cdev_device_del() is called
when this bit is not set.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211011132114.3663509-1-yangyingliang@huawei.com
Function m41t80_sqw_register_clk returns a pointer to struct clk,
so returning a plain 0 integer isn't good practice. Fix this by
returning a NULL instead.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210925223441.182673-1-colin.king@canonical.com
Shifting the u16 value returned by readw by 16 bits to the left
will be promoted to a 32 bit signed int and then sign-extended
to an unsigned long. If the top bit of the readw is set then
the shifted value will be sign extended and the top 32 bits of
the result will be set.
Fixes: be7d9c9161 ("rtc: Add support for the MSTAR MSC313 RTC")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210928134654.991923-1-colin.king@canonical.com
Currently autoloading for SPI devices does not use the DT ID table, it uses
SPI modalises. Supporting OF modalises is going to be difficult if not
impractical, an attempt was made but has been reverted, so ensure that
module autoloading works for this driver by adding an id_table listing the
SPI IDs for everything.
Fixes: 96c8395e21 ("spi: Revert modalias changes")
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210927130240.33693-1-broonie@kernel.org
This adds support for the RTC block on the Mstar MSC313e SoCs and newer.
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Co-developed-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Reviewed-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210823171613.18941-3-romain.perier@gmail.com
The MODULE_DEVICE_TABLE already creates proper alias for platform
driver. Having another MODULE_ALIAS causes the alias to be duplicated.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210916164604.134924-1-krzysztof.kozlowski@canonical.com
The MODULE_DEVICE_TABLE already creates proper alias for platform
driver. Having another MODULE_ALIAS causes the alias to be duplicated.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210916164513.134725-1-krzysztof.kozlowski@canonical.com
Currently autoloading for SPI devices does not use the DT ID table, it uses
SPI modalises. Supporting OF modalises is going to be difficult if not
impractical, an attempt was made but has been reverted, so ensure that
module autoloading works for this driver by adding an id_table listing the
SPI IDs for everything.
Fixes: 96c8395e21 ("spi: Revert modalias changes")
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210923194922.53386-4-broonie@kernel.org
Currently autoloading for SPI devices does not use the DT ID table, it uses
SPI modalises. Supporting OF modalises is going to be difficult if not
impractical, an attempt was made but has been reverted, so ensure that
module autoloading works for this driver by adding an id_table listing the
SPI IDs for everything.
Fixes: 96c8395e21 ("spi: Revert modalias changes")
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210923194922.53386-3-broonie@kernel.org
Currently autoloading for SPI devices does not use the DT ID table, it uses
SPI modalises. Supporting OF modalises is going to be difficult if not
impractical, an attempt was made but has been reverted, so ensure that
module autoloading works for this driver by adding an id_table listing the
SPI IDs for everything.
Fixes: 96c8395e21 ("spi: Revert modalias changes")
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210923194922.53386-2-broonie@kernel.org
The rtc-rx8010 uses the I2C regmap but doesn't select it in Kconfig so
depending on the configuration the build may fail. Fix it.
Signed-off-by: Yu-Tung Chang <mtwget@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210830052532.40356-1-mtwget@gmail.com
The RX-8035 is a newer RTC from EPSON that is very
similar to the RX-8025.
The key difference is in the oscillation stop (XSTP)
bit which is inverted on the RX-8035.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210709044518.28769-2-matt@traverse.com.au
It appears mc146818_get_time() and mc146818_set_time() now correctly
use the century register as specified in the ACPI FADT table. It is not
clear what else could be done here.
These comments were introduced by
commit 7be2c7c96a ("[PATCH] RTC framework driver for CMOS RTCs")
in 2007, which originally referenced function get_rtc_time() in
include/asm-generic/rtc.h .
Signed-off-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210716210437.29622-1-mat.jonczyk@o2.pl
The TPS65910 RTC driver module doesn't auto-load because of the wrong
module alias that doesn't match the device name, fix it.
Cc: stable@vger.kernel.org
Reported-by: Anton Bambura <jenneron@protonmail.com>
Tested-by: Anton Bambura <jenneron@protonmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210808160030.8556-1-digetx@gmail.com
As the documentation states, "The exact license information can only be
determined via the license information in the corresponding source files."
and the SPDX identifier has the proper information.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210810212008.631359-1-alexandre.belloni@bootlin.com
The current implementation of rtc_time64_to_tm() contains unnecessary
loops, branches and look-up tables. The new one uses an arithmetic-based
algorithm appeared in [1] and is approximately 4.3 times faster (YMMV).
The drawback is that the new code isn't intuitive and contains many 'magic
numbers' (not unusual for this type of algorithm). However, [1] justifies
all those numbers and, given this function's history, the code is unlikely
to need much maintenance, if any at all.
Add a KUnit test case that checks every day in a 160,000 years interval
starting on 1970-01-01 against the expected result. Add a new config
RTC_LIB_KUNIT_TEST symbol to give the option to run this test suite.
[1] Neri, Schneider, "Euclidean Affine Functions and Applications to
Calendar Algorithms". https://arxiv.org/abs/2102.06959
Signed-off-by: Cassio Neri <cassio.neri@gmail.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210624201343.85441-1-cassio.neri@gmail.com
The S5M8763X type seems to handles dates from year 0000 to 9999, there is
no info on leap year handling after 2099. The other models handles dates
from 2000 to 2099.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210804104133.5158-4-alexandre.belloni@bootlin.com
Call device_init_wakeup() only when alarms are available and the RTC is
actually able to wake up the system.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210804104133.5158-3-alexandre.belloni@bootlin.com
Clear the RTC_FEATURE_ALARM bit to signal to the core when alarms are not
available to ensure the alarm callbacks are never called and userspace is
aware alarms are not supported.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210804104133.5158-2-alexandre.belloni@bootlin.com
Switch to devm_rtc_allocate_device/devm_rtc_register_device, this allows
for further improvement of the driver.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210804104133.5158-1-alexandre.belloni@bootlin.com
arch/arm/mach-ixp4xx/include/mach/platform.h now gets included indirectly
and defines REG_OFFSET. Rename the register and bit definition to something
specific to the driver.
Fixes: 7fd70c65fa ("ARM: irqstat: Get rid of duplicated declaration")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210710211431.1393589-1-alexandre.belloni@bootlin.com
commit 03623b4b04 ("rtc: pcf2127: add tamper detection support")
added support for timestamp interrupts. However they are not being
handled in the irq handler. If a timestamp interrupt occurs it
results in kernel disabling the interrupt and displaying the call
trace:
[ 121.145580] irq 78: nobody cared (try booting with the "irqpoll" option)
...
[ 121.238087] [<00000000c4d69393>] irq_default_primary_handler threaded [<000000000a90d25b>] pcf2127_rtc_irq [rtc_pcf2127]
[ 121.248971] Disabling IRQ #78
Handle timestamp interrupts in pcf2127_rtc_irq(). Save time stamp
before clearing TSF1 and TSF2 flags so that it can't be overwritten.
Set a flag to mark if the timestamp is valid and only report to sysfs
if the flag is set. To mimic the hardware behavior, don’t save
another timestamp until the first one has been read by the userspace.
However, if the alarm irq is not configured, keep the old way of
handling timestamp interrupt in the timestamp0 sysfs calls.
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Tested-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210629150643.31551-1-ykaukab@suse.de
The offset variable is checked by at91_rtc_readalarm(), but this check
is unnecessary because the previous check knew that the value of this
variable was not 0.
This removes that unnecessary offset variable checks.
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210708051340.341345-1-nobuhiro1.iwamatsu@toshiba.co.jp
s5m_check_peding_alarm_interrupt() in s5m_rtc_read_alarm() gets the return
value, but doesn't use it.
This modifies using the s5m_check_peding_alarm_interrupt()"s return value
as the s5m_rtc_read_alarm()'s return value.
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: linux-samsung-soc@vger.kernel.org
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210708051304.341278-1-nobuhiro1.iwamatsu@toshiba.co.jp
For C files, use the C99 format (//).
Cc: Orson Zhai <orsonzhai@gmail.com>
Cc: Baolin Wang <baolin.wang7@gmail.com>
Cc: Chunyan Zhang <zhang.lyra@gmail.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210707075804.337458-6-nobuhiro1.iwamatsu@toshiba.co.jp
Here is the big set of IIO and staging driver patches for 5.14-rc1.
Loads of IIO driver updates and additions in here, the shortlog has the
full details.
For the staging side, we moved a few drivers out of staging, and deleted
the kpc2000 drivers as the original developer asked us to because no one
was working on them anymore.
Also in here are loads of coding style cleanups due to different intern
projects focusing on the staging tree to try to get experience doing
kernel development.
All of these have been in the linux-next tree for a while with no
reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYOM50w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykZ4wCeK/JreZijlAy0O5Gq1equvRx1jJoAoJmmt7UY
bx6qpcmUM7c53cMXr/kh
=6suo
-----END PGP SIGNATURE-----
Merge tag 'staging-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging / IIO driver updates from Greg KH:
"Here is the big set of IIO and staging driver patches for 5.14-rc1.
Loads of IIO driver updates and additions in here, the shortlog has
the full details.
For the staging side, we moved a few drivers out of staging, and
deleted the kpc2000 drivers as the original developer asked us to
because no one was working on them anymore.
Also in here are loads of coding style cleanups due to different
intern projects focusing on the staging tree to try to get experience
doing kernel development.
All of these have been in the linux-next tree for a while with no
reported problems"
* tag 'staging-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (744 commits)
staging: hi6421-spmi-pmic: cleanup some macros
staging: hi6421-spmi-pmic: change identation of a table
staging: hi6421-spmi-pmic: change a return code
staging: hi6421-spmi-pmic: better name IRQs
staging: hi6421-spmi-pmic: use devm_request_threaded_irq()
staging: hisilicon,hi6421-spmi-pmic.yaml: cleanup descriptions
spmi: hisi-spmi-controller: move driver from staging
phy: phy-hi3670-usb3: move driver from staging into phy
staging: rtl8188eu: remove include/rtw_debug.h header
staging: rtl8188eu: remove GlobalDebugLevel variable
staging: rtl8188eu: remove DRIVER_PREFIX preprocessor definition
staging: rtl8188eu: remove RT_TRACE macro
staging: rtl8188eu: remove all RT_TRACE calls from hal/rtl8188eu_recv.c
staging: rtl8188eu: remove all RT_TRACE calls from hal/hal_intf.c
staging: rtl8188eu: remove all RT_TRACE calls from hal/rtl8188eu_xmit.c
staging: rtl8188eu: remove all RT_TRACE calls from core/rtw_xmit.c
staging: rtl8188eu: remove all RT_TRACE calls from core/rtw_pwrctrl.c
staging: rtl8188eu: remove all RT_TRACE calls from core/rtw_recv.c
staging: rtl8188eu: remove all RT_TRACE calls from core/rtw_ioctl_set.c
staging: rtl8188eu: remove all RT_TRACE calls from core/rtw_ieee80211.c
...
The variable retval is being initialized with a value that is never read,
it is being updated later on. The assignment is redundant and can be
removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210609120050.185746-1-colin.king@canonical.com
The STM32MP1 RTC may have 2 clocks, the pclk and the rtc_ck.
If clk_prepare_enable() fails for the second clock (rtc_ck) we must only
call clk_disable_unprepare() for the first clock (pclk) but currently we
call it on both leading to a WARN:
[ 15.629568] WARNING: CPU: 0 PID: 146 at drivers/clk/clk.c:958 clk_core_disable+0xb0/0xc8
[ 15.637620] ck_rtc already disabled
[ 15.663322] CPU: 0 PID: 146 Comm: systemd-udevd Not tainted 5.4.77-pknbsp-svn5759-atag-v5.4.77-204-gea4235203137-dirty #2413
[ 15.674510] Hardware name: STM32 (Device Tree Support)
[ 15.679658] [<c0111148>] (unwind_backtrace) from [<c010c0b8>] (show_stack+0x10/0x14)
[ 15.687371] [<c010c0b8>] (show_stack) from [<c0ab3d28>] (dump_stack+0xc0/0xe0)
[ 15.694574] [<c0ab3d28>] (dump_stack) from [<c012360c>] (__warn+0xc8/0xf0)
[ 15.701428] [<c012360c>] (__warn) from [<c0123694>] (warn_slowpath_fmt+0x60/0x94)
[ 15.708894] [<c0123694>] (warn_slowpath_fmt) from [<c053b518>] (clk_core_disable+0xb0/0xc8)
[ 15.717230] [<c053b518>] (clk_core_disable) from [<c053c190>] (clk_core_disable_lock+0x18/0x24)
[ 15.725924] [<c053c190>] (clk_core_disable_lock) from [<bf0adc44>] (stm32_rtc_probe+0x124/0x5e4 [rtc_stm32])
[ 15.735739] [<bf0adc44>] (stm32_rtc_probe [rtc_stm32]) from [<c05f7d4c>] (platform_drv_probe+0x48/0x98)
[ 15.745095] [<c05f7d4c>] (platform_drv_probe) from [<c05f5cec>] (really_probe+0x1f0/0x458)
[ 15.753338] [<c05f5cec>] (really_probe) from [<c05f61c4>] (driver_probe_device+0x70/0x1c4)
[ 15.761584] [<c05f61c4>] (driver_probe_device) from [<c05f6580>] (device_driver_attach+0x58/0x60)
[ 15.770439] [<c05f6580>] (device_driver_attach) from [<c05f6654>] (__driver_attach+0xcc/0x170)
[ 15.779032] [<c05f6654>] (__driver_attach) from [<c05f40d8>] (bus_for_each_dev+0x58/0x7c)
[ 15.787191] [<c05f40d8>] (bus_for_each_dev) from [<c05f4ffc>] (bus_add_driver+0xdc/0x1f8)
[ 15.795352] [<c05f4ffc>] (bus_add_driver) from [<c05f6ed8>] (driver_register+0x7c/0x110)
[ 15.803425] [<c05f6ed8>] (driver_register) from [<c01027bc>] (do_one_initcall+0x70/0x1b8)
[ 15.811588] [<c01027bc>] (do_one_initcall) from [<c01a1094>] (do_init_module+0x58/0x1f8)
[ 15.819660] [<c01a1094>] (do_init_module) from [<c01a0074>] (load_module+0x1e58/0x23c8)
[ 15.827646] [<c01a0074>] (load_module) from [<c01a0860>] (sys_finit_module+0xa0/0xd4)
[ 15.835459] [<c01a0860>] (sys_finit_module) from [<c01011e0>] (__sys_trace_return+0x0/0x20)
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Fixes: 4e64350f42 ("rtc: add STM32 RTC driver")
Cc: stable@vger.kernel.org
Reviewed-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/1623087421-19722-1-git-send-email-martin.fuzzey@flowbird.group
The only known BD70528 use-cases are such that the PMIC is controlled
from separate MCU which is not running Linux. I am not aware of
any Linux driver users. Furthermore, it seems there is no demand for
this IC. Let's ease the maintenance burden and drop the driver. We can
always add it back if there is sudden need for it.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210527105819.GA3111334@localhost.localdomain
Interrupt line can be configured on different hardware in different way,
even inverted. Therefore driver should not enforce specific trigger
type - edge falling - but instead rely on Devicetree to configure it.
The Maxim 77686 datasheet describes the interrupt line as active low
with a requirement of acknowledge from the CPU therefore the edge
falling is not correct.
The interrupt line is shared between PMIC and RTC driver, so using level
sensitive interrupt is here especially important to avoid races. With
an edge configuration in case if first PMIC signals interrupt followed
shortly after by the RTC, the interrupt might not be yet cleared/acked
thus the second one would not be noticed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210526172036.183223-6-krzysztof.kozlowski@canonical.com
Fix the following make W=1 kernel build warnings:
drivers/rtc/rtc-m41t80.c:811: warning: expecting prototype for wdt_close(). Prototype was for wdt_release() instead
drivers/rtc/rtc-m41t80.c:830: warning: expecting prototype for notify_sys(). Prototype was for wdt_notify_sys() instead
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210517110641.473386-1-yangyingliang@huawei.com
Fix the following make W=1 kernel build warning:
drivers/rtc/sysfs.c:115: warning: expecting prototype for rtc_sysfs_show_hctosys(). Prototype was for hctosys_show() instead
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210517045901.3461800-1-yangyingliang@huawei.com
A namespace for exported symbols makes clear who is a provider
and who is a consumer of the certain resources. Besides that,
it doesn't pollute the common namespace.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20210614162447.5392-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch adds RTC_TC_MTH_MASK to support new chips.
Signed-off-by: Yuchen Huang <yuchen.huang@mediatek.com>
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The DryIce-based RTC supports alarms that trigger an interrupt.
Configure this interrupt as a wakeup source that wakes the system up
from standby mode.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210511161244.16111-1-martin@kaiser.cx
Ahmad Fatoum