When adjusting the link speed, the target frequency is determined by a
'swith (LINK_SPEED)' statement, that assigns the target rate only for
valid and expected LINK_SPEED values. This incomplete switch statement
leads to the following build warning:
drivers/net/ethernet/cadence/macb.c: In function 'macb_handle_link_change':
>> drivers/net/ethernet/cadence/macb.c:241:14: warning: 'rate' may be used uninitialized in this function [-Wmaybe-uninitialized]
netdev_warn(dev, "unable to generate target frequency: %ld Hz\n",
^
drivers/net/ethernet/cadence/macb.c:215:13: note: 'rate' was declared here
long ferr, rate, rate_rounded;
Fixing this by bailing out of that function in the switch's default case
before the rate variable is used.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adjust the ethernet clock according to the negotiated link speed.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the device managed interface to request the IRQ, simplifying error
paths.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the device managed version of ioremap to remap IO memory,
simplifying error paths.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Migrate to using the device managed interface for clocks and clean up
the associated error paths.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Migrate the suspend/resume functions to use the dev_pm_ops PM interface.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the last architecture switched to generic hard irqs the config
options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
for !CONFIG_GENERIC_HARDIRQS can be removed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace misleading -1 (-EPERM) by a more appropriate return code (-ENXIO)
in macb_mii_probe function.
Save macb_mii_probe return before branching to err_out_unregister to avoid
erronous 0 return.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macb driver only handle PHY description through platform_data
(macb_platform_data).
Thus, when using dt you cannot define phy properties like phy address or
phy irq pin.
This patch makes use of the of_mdiobus_register to add support for
phy device definition using dt.
A fallback to the autoscan procedure is added in case there is no phy
devices defined in dt.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit ab78029 (drivers/pinctrl: grab default handles from device core),
we can rely on device core for setting the default pins. Compile tested only.
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jongsung Kim <neidhard.kim@lge.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This has no dependency on any of the drivers under NET_CORE.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GEM is able to adapt its DMA buffer size, so change
the RX path to take advantage of this possibility and
remove all kind of memcpy in this path.
This modification introduces function pointers for managing
differences between MACB and GEM adapter type.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Macb Ethernet controller requires a RX buffer of 128 bytes. It is
highly sub-optimal for Gigabit-capable GEM that is able to use
a bigger DMA buffer. Change this constant and associated macros
with data stored in the private structure.
RX DMA buffer size has to be multiple of 64 bytes as indicated in
DMA Configuration Register specification.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d06310
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Roland Stigge <stigge@antcom.de>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Tested-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 749a2b6 (net/macb: clear tx/rx completion flags in ISR)
introduces clear-on-write on ISR register. This behavior is not always
implemented when using Cadence MACB/GEM and is breaking other platforms.
We are using the Design Configuration Register 1 information and a capability
property to actually activate this clear-on-write behavior on ISR.
Reported-by: Hein Tibosch <hein_tibosch@yahoo.es>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Hein Tibosch <hein_tibosch@yahoo.es>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If NO_DMA=y:
drivers/built-in.o: In function `macb_free_consistent':
drivers/net/ethernet/cadence/macb.c:878: undefined reference to `dma_free_coherent'
drivers/net/ethernet/cadence/macb.c:883: undefined reference to `dma_free_coherent'
drivers/net/ethernet/cadence/macb.c:888: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `macb_alloc_consistent':
drivers/net/ethernet/cadence/macb.c:905: undefined reference to `dma_alloc_coherent'
drivers/built-in.o: In function `macb_tx_interrupt':
drivers/net/ethernet/cadence/macb.c:515: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `macb_tx_error_task':
drivers/net/ethernet/cadence/macb.c:457: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `macb_start_xmit':
drivers/net/ethernet/cadence/macb.c:838: undefined reference to `dma_map_single'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If NO_DMA=y:
drivers/built-in.o: In function `at91ether_start':
drivers/net/ethernet/cadence/at91_ether.c:49: undefined reference to `dma_alloc_coherent'
drivers/net/ethernet/cadence/at91_ether.c:60: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `at91ether_interrupt':
drivers/net/ethernet/cadence/at91_ether.c:250: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `at91ether_start_xmit':
drivers/net/ethernet/cadence/at91_ether.c:169: undefined reference to `dma_map_single'
drivers/built-in.o: In function `at91ether_close':
drivers/net/ethernet/cadence/at91_ether.c:145: undefined reference to `dma_free_coherent'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return a negative error code from the error handling
case instead of 0, as returned elsewhere in this function.
Original-idea-by: <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return a negative error code from the error handling
case instead of 0, as returned elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
With of_get_mac_address() and of_get_phy_mode() now defined as dummy
functions if OF_NET is not configured, it is no longer necessary to
provide OF dependent functions as front-end. Also, the two functions
depend on OF_NET, not on OF, so the conditional code was not correct
anyway.
Drop the front-end functions and call of_get_mac_address() and
of_get_phy_mode() directly instead.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
With of_get_mac_address() and of_get_phy_mode() now defined as dummy
functions if OF_NET is not configured, it is no longer necessary to
provide OF dependent functions as front-end. Also, the two functions
depend on OF_NET, not on OF, so the conditional code was not correct
anyway.
Drop the front-end functions and call of_get_mac_address() and
of_get_phy_mode() directly instead.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use clk_prepare_enable/clk_disable_unprepare to be safe on SMP systems.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Fabio Estevam <festevam@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The core has a bit for swapping packet data endianism.
Reset default from Cadence is off. Xilinx however, who uses this core on the
Zynq SoCs, opted for on.
Force it to off. This shouldn't change the behaviour for current users of the
macb, but enables usage on Zynq devices.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At least in the cadence IP core on the Xilinx Zynq SoC the TCOMP/RCOMP flags
are not auto-cleaned. As these flags are evaluated, they need to be cleaned.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I believe these error messages are already logged
on allocation failure by warn_alloc_failed and so
get a dump_stack on OOM.
Remove the unnecessary additional error logging.
Around these deletions:
o Alignment neatening.
o Remove unnecessary casts of dma_alloc_coherent.
o Hoist assigns from ifs.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Emitting netdev_alloc_skb and netdev_alloc_skb_ip_align OOM
messages is unnecessary as there is already a dump_stack
after allocation failures.
Other trivial changes around these removals:
Convert a few comparisons of pointer to 0 to !pointer.
Change flow to remove unnecessary label.
Remove now unused variable.
Hoist assignment from if.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch uses module_platform_driver_probe() macro which makes
the code smaller and simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch uses module_platform_driver_probe() macro which makes
the code smaller and simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull s390 update from Martin Schwidefsky:
"The most prominent change in this patch set is the software dirty bit
patch for s390. It removes __HAVE_ARCH_PAGE_TEST_AND_CLEAR_DIRTY and
the page_test_and_clear_dirty primitive which makes the common memory
management code a bit less obscure.
Heiko fixed most of the PCI related fallout, more often than not
missing GENERIC_HARDIRQS dependencies. Notable is one of the 3270
patches which adds an export to tty_io to be able to resize a tty.
The rest is the usual bunch of cleanups and bug fixes."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (42 commits)
s390/module: Add missing R_390_NONE relocation type
drivers/gpio: add missing GENERIC_HARDIRQ dependency
drivers/input: add couple of missing GENERIC_HARDIRQS dependencies
s390/cleanup: rename SPP to LPP
s390/mm: implement software dirty bits
s390/mm: Fix crst upgrade of mmap with MAP_FIXED
s390/linker skript: discard exit.data at runtime
drivers/media: add missing GENERIC_HARDIRQS dependency
s390/bpf,jit: add vlan tag support
drivers/net,AT91RM9200: add missing GENERIC_HARDIRQS dependency
iucv: fix kernel panic at reboot
s390/Kconfig: sort list of arch selected config options
phylib: remove !S390 dependeny from Kconfig
uio: remove !S390 dependency from Kconfig
dasd: fix sysfs cleanup in dasd_generic_remove
s390/pci: fix hotplug module init
s390/pci: cleanup clp page allocation
s390/pci: cleanup clp inline assembly
s390/perf: cpum_cf: fallback to software sampling events
s390/mm: provide PAGE_SHARED define
...
Pull in 'net' to take in the bug fixes that didn't make it into
3.8-final.
Also, deal with the semantic conflict of the change made to
net/ipv6/xfrm6_policy.c A missing rt6->n neighbour release
was added to 'net', but in 'net-next' we no longer cache the
neighbour entries in the ipv6 routes so that change is not
appropriate there.
Signed-off-by: David S. Miller <davem@davemloft.net>
The AT91RM9200 driver call devm_request_irq() and therefore should
depend on GENERIC_HARDIRQS to prevent link/compile errors on plaforms
without GENERIC_HARDIRQS.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When interrupts are disabled, an RX condition can occur but
it is not reported when enabling interrupts again. We need to check
RSR and use napi_reschedule() if condition is met.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flags argument of the phy_{attach,connect,connect_direct} functions
is then used to assign a struct phy_device dev_flags with its value.
All callers but the tg3 driver pass the flag 0, which results in the
underlying PHY drivers in drivers/net/phy/ not being able to actually
use any of the flags they would set in dev_flags. This patch gets rid of
the flags argument, and passes phydev->dev_flags to the internal PHY
library call phy_attach_direct() such that drivers which actually modify
a phy device dev_flags get the value preserved for use by the underlying
phy driver.
Acked-by: Kosta Zertsekel <konszert@marvell.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add information to the DMA Configuration Register to
maximize system performance:
- rx/tx packet buffer full memory size
- allow possibility to use INCR16 if supported
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Joachim Eastwood <manabian@gmail.com
Signed-off-by: David S. Miller <davem@davemloft.net>
If ndo_validate_addr is set to the generic eth_validate_addr
function there is no point in calling is_valid_ether_addr
from driver ndo_open if ndo_open is not used elsewhere in
the driver.
With this change is_valid_ether_addr will be called from the
generic eth_validate_addr function. So there should be no change
in the actual behavior.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move to circular buffers management macro and correct an error
with circular buffer initial condition.
Without this patch, the macb_tx_ring_avail() function was
not reporting the proper ring availability at startup:
macb macb: eth0: BUG! Tx Ring full when queue awake!
macb macb: eth0: tx_head = 0, tx_tail = 0
And hanginig forever...
I remove the macb_tx_ring_avail() function and use the
proven macros from circ_buf.h. CIRC_CNT() is used in the
"consumer" part of the driver: macb_tx_interrupt() to match
advice from Documentation/circular-buffers.txt.
Reported-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the first register set is used for matching but
we support getting the initial hw addr from any of
the registers.
To prevent stale entries and false matches clear unused
register sets. This most important for the at91_ether
driver where u-boot always uses the 2nd register set.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert all printk's to netdev_ counterparts and fix up some
printed texts.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No longer used after gpio phy interrupt support was
removed from at91_ether.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is used on one AT91RM9200 board where a bootloader stores
the Ethernet address in the wrong order.
Support this on macb so address setting functions can be shared
with the at91_ether driver.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macb driver in u-boot uses the first register set while
the at91_ether driver in u-boot uses the second register set.
By checking all register set, like at91_ether does, this code
can be shared between the drivers.
This only changes behavior on macb if no vaild address
is found in the first register set.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Soren Brinkmann