This mostly consolidates the Book3E and Book3S behaviour in boot WRT
executing from the physical or virtual address.
Book3E sets up kernel virtual linear map in start_initialization_book3e
and runs from the virtual linear alias after that. This change makes
Book3S begin to execute from the virtual alias at the same point. Book3S
can not use its MMU for that at this point, but when the MMU is disabled,
the virtual linear address correctly aliases to physical memory because
the top bits of the address are ignored with MMU disabled.
Secondaries execute from the virtual address similarly early.
This reduces the differences between subarchs, but the main motivation
was to enable the PC-relative addressing ABI for Book3S, where pointer
calculations must execute from the virtual address or the top bits of
the pointer will be lost. This is similar to the requirement the TOC
relative addressing already has that the TOC pointer use its virtual
address.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230408021752.862660-3-npiggin@gmail.com
A later change moves the non-prom case to run at the virtual address
earlier, which calls for virtual TOC and kernel base. Split these two
calculations for prom and non-prom to make that change simpler.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Retain relative_toc call for start_initialization_book3e]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230408021752.862660-2-npiggin@gmail.com
"fsl,P2020RDB-PC" compatible string was present in Turris 1.x DTS file just
because Linux kernel required it for proper detection of P2020 processor
during boot.
This was quite a hack as CZ.NIC Turris 1.x is not compatible with
Freescale P2020-RDB-PC board.
Now when kernel has generic unified support for boards with P2020
processors, there is no need to have this "hack" in turris1x.dts file.
So remove incorrect "fsl,P2020RDB-PC" compatible string from turris1x.dts.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230408140122.25293-14-pali@kernel.org
Generic unified P2020 machine description which supports all P2020-based
boards is now in separate file p2020.c. So create a separate config option
CONFIG_PPC_P2020 for it.
Previously machine descriptions for P2020 boards were enabled by
CONFIG_MPC85xx_DS or CONFIG_MPC85xx_RDB option. So set CONFIG_PPC_P2020 to
be enabled by default when one of those option is enabled.
This allows to compile support for P2020 boards without need to have
enabled support for older mpc85xx boards. And to compile kernel for old
mpc85xx boards without having enabled support for new P2020 boards.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230408140122.25293-13-pali@kernel.org
Combine machine descriptions and code of all P2020 boards into just one
generic unified P2020 machine description. This allows kernel to boot on
any P2020-based board with P2020 DTS file without need to patch kernel and
define a new machine description in 85xx powerpc platform directory.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230408140122.25293-12-pali@kernel.org
Make just one .setup_arch and one .init_IRQ callback implementation for all
P2020 board code. This deduplicate repeated and same code.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230408140122.25293-11-pali@kernel.org
In order to share mpc85xx i8259 code between DS and P2020.
Prefix i8259 debug and error messages by i8259 word.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
[mpe: Fix some coding style warnings in the moved code]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230408140122.25293-10-pali@kernel.org
This moves P2020 RDB machine descriptions into new p2020.c source file.
This is preparation for code de-duplication and providing one unified
machine description for all P2020 boards.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230408140122.25293-9-pali@kernel.org
This moves P2020 DS machine descriptions into new p2020.c source file.
This is preparation for code de-duplication and providing one unified
machine description for all P2020 boards.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230408140122.25293-8-pali@kernel.org
mpc85xx_qe_par_io_init() is a stub when CONFIG_QUICC_ENGINE is not set.
CONFIG_UCC_GETH and CONFIG_SERIAL_QE depend on CONFIG_QUICC_ENGINE.
Remove #ifdef CONFIG_QUICC_ENGINE
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230408140122.25293-7-pali@kernel.org
All necessary items are declared all the time, no need to use
a #ifdef CONFIG_PPC_I8259.
Refactor CONFIG_PPC_I8259 actions into a dedicated init function.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230408140122.25293-6-pali@kernel.org
Use pr_debug() instead of printk(KERN_DEBUG
Use pr_err() instead of printk(KERN_ERR
Use pr_info() instead of printk(KERN_INFO or printk("
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230408140122.25293-5-pali@kernel.org
No need to BUG() in case mpic_alloc() fails. Use WARN_ON().
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230408140122.25293-4-pali@kernel.org
Reduce number of lines in the call to mpic_alloc().
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230408140122.25293-3-pali@kernel.org
DBG() macro is defined at three places while used only
one time at one place.
Replace its only use by a pr_debug() and remove the macro.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230408140122.25293-2-pali@kernel.org
Function uli_exclude_device() is not used outside of the fsl_uli1575.c
source file anymore. So mark it as static and remove public prototype.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230409000812.18904-9-pali@kernel.org
After calling fsl_pci_assign_primary(), it is possible to use uli_init() to
conditionally initialize ppc_md.pci_exclude_device callback based on the
uli1575 detection.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230409000812.18904-8-pali@kernel.org
ULI1575 PCIe south bridge exists only on some Freescale boards. Allow to
disable CONFIG_FSL_ULI1575 symbol when it is not explicitly selected and
only implied. This is achieved by marking symbol as visible by providing
short description. Also adds dependency for this symbol to prevent enabling
it on platforms on which driver does not compile.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230409000812.18904-7-pali@kernel.org
Boards provided by CONFIG_MPC85xx_RDB option do not initialize
fsl_uli1575.c driver. So remove explicit select dependency on it.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230409000812.18904-6-pali@kernel.org
Move uli_init() function into existing driver fsl_uli1575.c file in order
to share its code between more platforms and board files.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230409000812.18904-5-pali@kernel.org
Function uli_exclude_device() is called only from mpc86xx_exclude_device()
and mpc85xx_exclude_device() functions. Both those functions are same, so
merge its logic directly into the uli_exclude_device() function.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230409000812.18904-4-pali@kernel.org
Function mpc85xx_exclude_device() is installed and used only when
pci_with_uli is fsl_pci_primary. So replace check for pci_with_uli by
fsl_pci_primary in mpc85xx_exclude_device() and move pci_with_uli variable
declaration into function mpc85xx_ds_uli_init() where it is used.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230409000812.18904-3-pali@kernel.org
Use a single line for uli_exclude_device().
Add uli_exclude_device() prototype in ppc-pci.h and guard it.
Remove that prototype from mpc85xx_ds.c and mpc86xx_hpcn.c files.
Make uli_pirq_to_irq[] static as it is used only in that file.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230409000812.18904-2-pali@kernel.org
-mcpu=power10 will generate prefixed and pcrel code by default, which
we do not support. The general kernel disables these with cflags, but
those were missed for the boot wrapper.
Fixes: 4b2a9315f2 ("powerpc/64s: POWER10 CPU Kconfig build option")
Cc: stable@vger.kernel.org # v6.1+
Reported-by: Danny Tsen <dtsen@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230407040909.230998-1-npiggin@gmail.com
Use the preferred form of branch-and-link for finding the current
address so objtool doesn't think it is an unannotated intra-function
call.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230407040924.231023-1-npiggin@gmail.com
When building with W=1 after commit 80b6093b55 ("kbuild: add -Wundef
to KBUILD_CPPFLAGS for W=1 builds"), the following warning occurs.
In file included from arch/powerpc/kvm/bookehv_interrupts.S:26:
arch/powerpc/kvm/../kernel/head_booke.h:20:6: warning: "THREAD_SHIFT" is not defined, evaluates to 0 [-Wundef]
20 | #if (THREAD_SHIFT < 15)
| ^~~~~~~~~~~~
THREAD_SHIFT is defined in thread_info.h but it is not directly included
in head_booke.h, so it is possible for THREAD_SHIFT to be undefined. Add
the include to ensure that THREAD_SHIFT is always defined.
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/202304050954.yskLdczH-lkp@intel.com/
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230406-wundef-thread_shift_booke-v1-1-8deffa4d84f9@kernel.org
syscalls do not set the PPR field in their interrupt frame and
return from syscall always sets the default PPR for userspace,
so setting the value in the ret_from_fork frame is not necessary
and mildly inconsistent. Remove it.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230325122904.2375060-9-npiggin@gmail.com
In the kernel user thread path, don't set _TIF_RESTOREALL because
the thread is required to call kernel_execve() before it returns,
which will set _TIF_RESTOREALL if necessary via start_thread().
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230325122904.2375060-8-npiggin@gmail.com
Kernel created user threads start similarly to kernel threads in that
they call a kernel function after first returning from _switch, so
they share ret_from_kernel_thread for this. Kernel threads never return
from that function though, whereas user threads often do (although some
don't, e.g., IO threads).
Split these startup functions in two, and catch kernel threads that
improperly return from their function. This is intended to make the
complicated code a little bit easier to understand.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230325122904.2375060-7-npiggin@gmail.com
When copy_thread is given a kernel function to run in arg->fn, this
does not necessarily mean it is a kernel thread. User threads can be
created this way (e.g., kernel_init, see also x86's copy_thread()).
These threads run a kernel function which may call kernel_execve()
and return, which returns like a userspace exec(2) syscall.
Kernel threads are to be differentiated with PF_KTHREAD, will always
have arg->fn set, and should never return from that function, instead
calling kthread_exit() to exit.
Create separate paths for the kthread and user kernel thread creation
logic. The kthread path will never exit and does not require a user
interrupt frame, so it gets a minimal stack frame.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230325122904.2375060-6-npiggin@gmail.com
If the system call return path always restores NVGPRs then there is no
need for ret_from_fork to do it. The HANDLER_RESTORE_NVGPRS does the
right thing for this.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230325122904.2375060-5-npiggin@gmail.com
The kernel thread path in copy_thread creates a user interrupt frame on
stack and stores the function and arg parameters there, and
ret_from_kernel_thread loads them. This is a slightly confusing way to
overload that frame. Non-volatile registers are loaded from the switch
frame, so the parameters can be stored there. The user interrupt frame
is now only used by user threads when they return to user.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230325122904.2375060-4-npiggin@gmail.com
The ret_from_fork code for 64e and 32-bit set r3 for
syscall_exit_prepare the same way that 64s does, so there should
be no need to special-case them in copy_thread.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230325122904.2375060-3-npiggin@gmail.com
The pkey registers (AMR, IAMR) do not get loaded from the switch frame
so it is pointless to save anything there. Remove the dead code.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230325122904.2375060-2-npiggin@gmail.com
The amdgpu driver builds some of its code with hard-float enabled,
whereas the rest of the kernel is built with soft-float.
When building with 64-bit long double, if soft-float and hard-float
objects are linked together, the build fails due to incompatible ABI
tags.
In the past there have been build errors in the amdgpu driver caused by
this, some of those were due to bad intermingling of soft & hard-float
code, but those issues have now all been fixed since commit 58ddbecb14
("drm/amd/display: move remaining FPU code to dml folder").
However it's still possible for soft & hard-float objects to end up
linked together, if the amdgpu driver is built-in to the kernel along
with the test_emulate_step.c code, which uses soft-float. That happens
in an allyesconfig build.
Currently those build errors are avoided because the amdgpu driver is
gated on 128-bit long double being enabled. But that's not a detail the
amdgpu driver should need to be aware of, and if another driver starts
using hard-float the same problem would occur.
All versions of the 64-bit ABI specify that long-double is 128-bits.
However some compilers, notably the kernel.org ones, are built to use
64-bit long double by default.
Apart from this issue of soft vs hard-float, the kernel doesn't care
what size long double is. In particular the kernel using 128-bit long
double doesn't impact userspace's ability to use 64-bit long double, as
musl does.
So always build the 64-bit kernel with 128-bit long double. That should
avoid any build errors due to the incompatible ABI tags. Excluding the
code that uses soft/hard-float, the vmlinux is identical with/without
the flag.
It does mean any code which is incorrectly intermingling soft &
hard-float code will build without error, so those bugs will need to be
caught by testing rather than at build time.
For more background see:
- commit d11219ad53 ("amdgpu: disable powerpc support for the newer display engine")
- commit c653c59178 ("drm/amdgpu: Re-enable DCN for 64-bit powerpc")
- https://lore.kernel.org/r/dab9cbd8-2626-4b99-8098-31fe76397d2d@app.fastmail.com
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Segher Boessenkool <segher@kernel.crashing.org>
Link: https://msgid.link/20230404102847.3303623-1-mpe@ellerman.id.au
Remove arch_atomic_try_cmpxchg_lock function as it is no longer used
since commit 9f61521c7a ("powerpc/qspinlock: powerpc qspinlock
implementation")
Signed-off-by: Nysal Jan K.A <nysal@linux.ibm.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230224103940.1328725-1-nysal@linux.ibm.com
Walks the stack when copy_{to,from}_user address is in the stack to
ensure that the object being copied is entirely a single stack frame and
does not contain stack metadata.
Substantially similar to the x86 implementation. The back chain is used
to traverse the stack and identify stack frame boundaries.
Signed-off-by: Nicholas Miehlbradt <nicholas@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230228054355.300628-1-nicholas@linux.ibm.com
Replace open coded reading of "reg" or of_get_address()/
of_translate_address() calls with a single call to
of_address_to_resource().
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230329220337.141295-1-robh@kernel.org
Replace of_get_property()+of_translate_address()+ioremap() with a call
to of_iomap() which does all those steps.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230327223109.820381-1-robh@kernel.org
Replace of_address_to_resource()+ioremap() with a call to of_iomap()
which does both of those steps.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230327223103.820229-1-robh@kernel.org
icp_native_init_one_node() only needs the number of entries in "reg".
Replace the open coded "reg" parsing with of_address_count() to get the
number of "reg" entries.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230327223056.820086-1-robh@kernel.org
"ranges" is a standard property with common parsing functions. Users
shouldn't be implementing their own parsing of it. Reimplement the
ISA brige "ranges" parsing using the common ranges iterator functions.
The common routines are flexible enough to work on PCI and non-PCI to
ISA bridges, so refactor pci_process_ISA_OF_ranges() and
isa_bridge_init_non_pci() into a single implementation.
Signed-off-by: Rob Herring <robh@kernel.org>
[mpe: Unsplit some strings and use pr_xxx()]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230327223045.819852-1-robh@kernel.org
Now that we can read prefixed instructions from a HV KVM guest and
emulate prefixed load/store instructions to emulated MMIO locations,
we can add HFSCR_PREFIXED into the set of bits that are set in the
HFSCR for a HV KVM guest on POWER10, allowing the guest to use
prefixed instructions.
PR KVM has not yet been extended to handle prefixed instructions in
all situations where we might need to emulate them, so prevent the
guest from enabling prefixed instructions in the FSCR for now.
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Tested-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Tested-by: Sachin Sant <sachinp@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/ZAgs25dCmLrVkBdU@cleo
In order to handle emulation of prefixed instructions in the guest,
this first makes vcpu->arch.last_inst be an unsigned long, i.e. 64
bits on 64-bit platforms. For prefixed instructions, the upper 32
bits are used for the prefix and the lower 32 bits for the suffix, and
both halves are byte-swapped if the guest endianness differs from the
host.
Next, vcpu->arch.emul_inst is now 64 bits wide, to match the HEIR
register on POWER10. Like HEIR, for a prefixed instruction it is
defined to have the prefix is in the top 32 bits and the suffix in the
bottom 32 bits, with both halves in the correct byte order.
kvmppc_get_last_inst is extended on 64-bit machines to put the prefix
and suffix in the right places in the ppc_inst_t being returned.
kvmppc_load_last_inst now returns the instruction in an unsigned long
in the same format as vcpu->arch.last_inst. It makes the decision
about whether to fetch a suffix based on the SRR1_PREFIXED bit in the
MSR image stored in the vcpu struct, which generally comes from SRR1
or HSRR1 on an interrupt. This bit is defined in Power ISA v3.1B to
be set if the interrupt occurred due to a prefixed instruction and
cleared otherwise for all interrupts except for instruction storage
interrupt, which does not come to the hypervisor. It is set to zero
for asynchronous interrupts such as external interrupts. In previous
ISA versions it was always set to 0 for all interrupts except
instruction storage interrupt.
The code in book3s_hv_rmhandlers.S that loads the faulting instruction
on a HDSI is only used on POWER8 and therefore doesn't ever need to
load a suffix.
[npiggin@gmail.com - check that the is-prefixed bit in SRR1 matches the
type of instruction that was fetched.]
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Tested-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/ZAgsq9h1CCzouQuV@cleo
This changes kvmppc_get_last_inst() so that the instruction it fetches
is returned in a ppc_inst_t variable rather than a u32. This will
allow us to return a 64-bit prefixed instruction on those 64-bit
machines that implement Power ISA v3.1 or later, such as POWER10.
On 32-bit platforms, ppc_inst_t is 32 bits wide, and is turned back
into a u32 by ppc_inst_val, which is an identity operation on those
platforms.
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Tested-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/ZAgsiPlL9O7KnlZZ@cleo
Pass the hypervisor (H)SRR1[PREFIX] indication through to synchronous
interrupts injected into the guest.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230330103224.3589928-3-npiggin@gmail.com
The prefix architecture in ISA v3.1 introduces a prefixed bit in SRR1
for many types of synchronous interrupts which is set when the interrupt
is caused by a prefixed instruction.
This requires KVM to be able to set this bit when injecting interrupts
into a guest. Plumb through the SRR1 "flags" argument to the core_queue
APIs where it's missing for this. For now they are set to 0, which is
no change.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Fixup kvmppc_core_queue_alignment() in booke.c]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230330103224.3589928-2-npiggin@gmail.com
Fix various W=1 warnings in booke.c:
arch/powerpc/kvm/booke.c:1008:5: error: no previous prototype for ‘kvmppc_handle_exit’ [-Werror=missing-prototypes]
1008 | int kvmppc_handle_exit(struct kvm_vcpu *vcpu, unsigned int exit_nr)
| ^~~~~~~~~~~~~~~~~~
arch/powerpc/kvm/booke.c:1009: warning: Function parameter or member 'vcpu' not described in 'kvmppc_handle_exit'
arch/powerpc/kvm/booke.c:1009: warning: Function parameter or member 'exit_nr' not described in 'kvmppc_handle_exit'
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/202304020827.3LEZ86WB-lkp@intel.com/
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230403045314.3095410-1-mpe@ellerman.id.au
It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties. As
part of this, convert of_get_property/of_find_property calls to the
recently added of_property_present() helper when we just want to test
for presence of a property and nothing more.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230310144735.1546817-1-robh@kernel.org
Nicholas Piggin