In the mrecv() function the Cadence I2C driver has the following expression
in an if clause.
((id->p_msg->flags & I2C_M_RECV_LEN) != I2C_M_RECV_LEN) &&
(id->recv_count <= CDNS_I2C_FIFO_DEPTH))
Earlier in the same function when I2C_M_RECV_LEN is set the recv_count is
initialized to a value that is larger than CDNS_I2C_FIFO_DEPTH. This means
if the first expression is false the second expression is also false.
Checking the first expression is thus redundant and can be removed.
This slightly simplifies the logic.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The irq field of the driver state struct is only used in the probe
function. There is no need to keep it around. Remove it from the state
struct and use a on-stack variable instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The CDNS_I2C_DATA_INTR_DEPTH is not used in the Cadence I2C driver. Remove
it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Commit "i2c: cadence: Add standard bus recovery support" breaks for i2c
devices that have no pinctrl defined. There is no requirement for this
to exist in the DT. This has worked perfectly well without this before in
at least 1 real usage case on hardware (Mali Komeda DPU, Cadence i2c to
talk to a tda99xx phy). Adding the requirement to have pinctrl set up in
the device tree (or otherwise be found) is a regression where the whole
i2c device is lost entirely (in this case dropping entire devices which
then leads to the drm display stack unable to find the phy for display
output, thus having no drm display device and so on down the chain).
This converts the above commit to an enhancement if pinctrl can be found
for the i2c device, providing a timeout on read with recovery, but if not,
do what used to be done rather than a fatal loss of a device.
This restores the mentioned display devices to their working state again.
Fixes: 58b924241d ("i2c: cadence: Add standard bus recovery support")
Signed-off-by: Carsten Haitzler <carsten.haitzler@arm.com>
Reviewed-by: Shubhrajyoti Datta <shubhrajyoti.datta@amd.com>
Reviewed-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Acked-by: Michal Simek <michal.simek@amd.com>
[wsa: added braces to else-branch]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Hook up the standard GPIO/pinctrl-based recovery support.
We are doing the recovery at the beginning on a timeout.
Multiple people have contributed to the series.
Original patch from Cirag and another one from Robert.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
- quite some DT schema conversions and extensions
- and a bunch of driver updates and improvements
-----BEGIN PGP SIGNATURE-----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=6fXH
-----END PGP SIGNATURE-----
Merge tag 'i2c-for-5.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
- new drivers: Microchip CoreI2C, Renesas RZV2M
- quite some DT schema conversions and extensions
- and a bunch of driver updates and improvements
* tag 'i2c-for-5.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (37 commits)
i2c: extend documentation about retvals of master_xfer functions
i2c: mux-gpmux: Add of_node_put() when breaking out of loop
dt-bindings: i2c: i2c-rk3x: Document Rockchip RV1126
i2c: qcom-geni: Use the correct return value
i2c: cadence: Support PEC for SMBus block read
i2c: qcom-geni: Propagate GENI_ABORT_DONE to geni_i2c_abort_xfer()
i2c: brcmstb: Use dev_name() for adapter name
i2c: Add Renesas RZ/V2M controller
dt-bindings: i2c: Document RZ/V2M I2C controller
i2c: mlxcpld: Add callback to notify probing completion
i2c: scmi: Replace open coded device_get_match_data()
i2c: stm32: add support for the STM32MP13 soc
dt-bindings: i2c: st,stm32-i2c: add entry for stm32mp13
dt-bindings: i2c: i2c-rk3x: add rk3588 compatible
i2c: add support for microchip fpga i2c controllers
i2c: i801: Add support for Intel Meteor Lake-P
dt-bindings: i2c: nomadik: Add power domain to binding
dt-bindings: i2c: nomadik: Drop unused voltage supply from example
i2c: Fix a potential use after free
i2c: hisi: use HZ_PER_KHZ macro in units.h
...
SMBus packet error checking (PEC) is implemented by appending one
additional byte of checksum data at the end of the message. This provides
additional protection and allows to detect data corruption on the I2C bus.
SMBus block reads support variable length reads. The first byte in the read
message is the number of available data bytes.
The combination of PEC and block read is currently not supported by the
Cadence I2C driver.
* When PEC is enabled the maximum transfer length for block reads
increases from 33 to 34 bytes.
* The I2C core smbus emulation layer relies on the driver updating the
`i2c_msg` `len` field with the number of received bytes. The updated
length is used when checking the PEC.
Add support to the Cadence I2C driver for handling SMBus block reads with
PEC. To determine the maximum transfer length uses the initial `len` value
of the `i2c_msg`. When PEC is enabled this will be 2, when it is disabled
it will be 1.
Once a read transfer is done also increment the `len` field by the amount
of received data bytes.
This change has been tested with a UCM90320 PMBus power monitor, which
requires block reads to access certain data fields, but also has PEC
enabled by default.
Fixes: df8eb5691c ("i2c: Add driver for Cadence I2C controller")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Shubhrajyoti Datta <Shubhrajyoti.datta@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Problems were observed on the Xilinx ZynqMP platform with large I2C reads.
When a read of 277 bytes was performed, the controller NAKed the transfer
after only 252 bytes were transferred and returned an ENXIO error on the
transfer.
There is some code in cdns_i2c_master_isr to handle this case by resetting
the transfer count in the controller before it reaches 0, to allow larger
transfers to work, but it was conditional on the CDNS_I2C_BROKEN_HOLD_BIT
quirk being set on the controller, and ZynqMP uses the r1p14 version of
the core where this quirk is not being set. The requirement to do this to
support larger reads seems like an inherently required workaround due to
the core only having an 8-bit transfer size register, so it does not
appear that this should be conditional on the broken HOLD bit quirk which
is used elsewhere in the driver.
Remove the dependency on the CDNS_I2C_BROKEN_HOLD_BIT for this transfer
size reset logic to fix this problem.
Fixes: 63cab195bf ("i2c: removed work arounds in i2c driver for Zynq Ultrascale+ MPSoC")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Shubhrajyoti Datta <Shubhrajyoti.datta@amd.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
This patch ensures that the clock notifier is unregistered
when driver probe is returning error.
Fixes: df8eb5691c ("i2c: Add driver for Cadence I2C controller")
Signed-off-by: Satish Nagireddy <satish.nagireddy@getcruise.com>
Tested-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Timeout as 1 second sets an upper limit on the length
of the transfer executed, but there is no maximum length
of a write or read message set in i2c_adapter_quirks for
this controller.
This upper limit affects devices that require sending
large firmware blobs over I2C.
To remove that limitation, calculate the minimal time
necessary, plus some wiggle room, for every message and
use it instead of the default one second, if more than
one second.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The zynqmp platform now supports chip-off so the registers can
lose context.
Implement save restore for i2c module.
Since we have only a couple of registers
an unconditional restore is done.
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Pull i2c updates from Wolfram Sang:
- core supports now bus regulators controlling power for SCL/SDA
- quite some DT binding conversions to YAML
- added a seperate DT binding for the optional SMBus Alert feature
- documentation with examples how to deal with I2C sysfs files
- some bigger rework for the i801 driver
- and a few usual driver updates
* 'i2c/for-mergewindow' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (42 commits)
i2c: ali1535: mention that the device should not be disabled
i2c: mpc: Restore reread of I2C status register
i2c: core-smbus: Expose PEC calculate function for generic use
Documentation: i2c: Add doc for I2C sysfs
i2c: core: Disable client irq on reboot/shutdown
dt-bindings: i2c: update bindings for MT8195 SoC
i2c: imx: Fix some checkpatch warnings
i2c: davinci: Simplify with dev_err_probe()
i2c: cadence: Simplify with dev_err_probe()
i2c: xiic: Simplify with dev_err_probe()
i2c: cadence: Clear HOLD bit before xfer_size register rolls over
dt-bindings: i2c: ce4100: Replace "ti,pcf8575" by "nxp,pcf8575"
i2c: i801: Improve i801_setup_hstcfg
i2c: i801: Use driver name constant instead of function dev_driver_string
i2c: i801: Simplify initialization of i2c_board_info in i801_probe_optional_slaves
i2c: i801: Improve status polling
i2c: cht-wc: Replace of_node by NULL
i2c: riic: Add RZ/G2L support
dt-bindings: i2c: renesas,riic: Document RZ/G2L I2C controller
dt-bindings: i2c: renesas,iic: Convert to json-schema
...
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
On Xilinx zynq SOC if the delay between address register write and
control register write in cdns_mrecv function is more, the xfer size
register rolls over and controller is stuck. This is an IP bug and
is resolved in later versions of IP.
To avoid this scenario, disable the interrupts on the current processor
core between the two register writes and enable them later. This can
help achieve the timing constraint.
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/i2c/busses/i2c-cadence.c:157: warning: expecting prototype for enum cdns_i2c_slave_mode. Prototype was for enum cdns_i2c_slave_state instead
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to devm_request_irq() (which
takes *unsigned* IRQ #), causing it to fail with -EINVAL, overriding
an original error code. Stop calling devm_request_irq() with invalid
IRQ #s.
Fixes: df8eb5691c ("i2c: Add driver for Cadence I2C controller")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The PM reference count is not expected to be incremented on
return in functions cdns_i2c_master_xfer and cdns_reg_slave.
However, pm_runtime_get_sync will increment pm usage counter
even failed. Forgetting to putting operation will result in a
reference leak here.
Replace it with pm_runtime_resume_and_get to keep usage
counter balanced.
Fixes: 7fa32329ca ("i2c: cadence: Move to sensible power management")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
There are few issues on Zynq SOC observed in the stress tests causing
timeout errors. Even though all the data is received, timeout error
is thrown. This is due to an IP bug in which the COMP bit in ISR is
not set at end of transfer and completion interrupt is not generated.
This bug is seen on Zynq platforms when the following condition occurs:
Master read & HOLD bit set & Transfer size register reaches '0'.
One workaround is to clear the HOLD bit before the transfer size
register reaches '0'. The current implementation checks for this at
the start of the loop and also only for less than FIFO DEPTH case
(ignoring the equal to case).
So clear the HOLD bit when the data yet to receive is less than or
equal to the FIFO DEPTH. This avoids the IP bug condition.
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
This reverts commit d358def706.
There are two issues with "i2c: cadence: Fix the hold bit setting" commit.
1. In case of combined message request from user space, when the HOLD
bit is cleared in cdns_i2c_mrecv function, a STOP condition is sent
on the bus even before the last message is started. This is because when
the HOLD bit is cleared, the FIFOS are empty and there is no pending
transfer. The STOP condition should occur only after the last message
is completed.
2. The code added by the commit is redundant. Driver is handling the
setting/clearing of HOLD bit in right way before the commit.
The setting of HOLD bit based on 'bus_hold_flag' is taken care in
cdns_i2c_master_xfer function even before cdns_i2c_msend/cdns_i2c_recv
functions.
The clearing of HOLD bit is taken care at the end of cdns_i2c_msend and
cdns_i2c_recv functions based on bus_hold_flag and byte count.
Since clearing of HOLD bit is done after the slave address is written to
the register (writing to address register triggers the message transfer),
it is ensured that STOP condition occurs at the right time after
completion of the pending transfer (last message).
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Added support for I2C slave functionality
Signed-off-by: Chirag Parekh <chirag.parekh@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Radu Pirea <radu_nicolae.pirea@upb.ro>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
use devm_platform_get_and_ioremap_resource() to simplify code, which
contains platform_get_resource() and devm_ioremap_resource(), it also
get the resource for use by the following code.
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fix wording based on checkpatch.pl
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
E.g. pm_runtime_set_active must be called while the power
management system is disabled. Fixes extra hanging clk_enable.
Signed-off-by: Topi Kuutela <topi.kuutela@gmail.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Do not print error in case of EPROBE_DEFER.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Under certain conditions, Cadence's I2C controller's transfer_size
register will roll over and generate invalid read transactions. Before
this change, the ISR relied solely on the RXDV bit to determine when to
write more data to the user's buffer. The invalid read data would cause
overruns, smashing stacks and worse.
This change stops the buffer writes to the requested boundary and
reports the error. The controller will be reset so normal transactions
may resume.
Signed-off-by: Alex Williams <alex.williams@ni.com>
Reviewed-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com> # in a seperate mail
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case the hold bit is not needed we are carrying the old values.
Fix the same by resetting the bit when not needed.
Fixes the sporadic i2c bus lockups on National Instruments
Zynq-based devices.
Fixes: df8eb5691c ("i2c: Add driver for Cadence I2C controller")
Reported-by: Kyle Roeschley <kyle.roeschley@ni.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Tested-by: Kyle Roeschley <kyle.roeschley@ni.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Several drivers call to_platform_device() to get platform_device
and pass it to platform_get_drvdata(). In platform_get_drvdata(),
the platform_device is converted back to struct device again.
Use dev_get_drvdata() to avoid platform_device/device dance.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> (for DesignWare only)
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The driver was clearing the hold bit in the control register before
writing to the address register which resulted in a stop condition
being generated rather than a repeated start.
This issue was only observed when a system was running much
slower than a normal processor would execute. The IP data sheet
mentions a ordering of writing to the address register before
clearing the hold.
Fixes: df8eb5691c ("i2c: Add driver for Cadence I2C controller")
Signed-off-by: John Linn <john.linn@xilinx.com>
Signed-off-by: Paresh Chaudhary <paresh.chaudhary@rockwellcollins.com>
Signed-off-by: Matthew Weber <matthew.weber@rockwellcollins.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The cadence I2C driver calls cdns_i2c_writereg(..) to setup a workaround
in the controller, but did so after calling i2c_add_adapter() which starts
probing devices on the bus. Change the order so that the configuration is
completely finished before using the adapter.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
"Here is the 4.9 pull request from I2C including:
- centralized error messages when registering to the core
- improved lockdep annotations to prevent false positives
- DT support for muxes, gates, and arbitrators
- bus speeds can now be obtained from ACPI
- i2c-octeon got refactored and now supports ThunderX SoCs, too
- i2c-tegra and i2c-designware got a bigger bunch of updates
- a couple of standard driver fixes and improvements"
* 'i2c/for-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (71 commits)
i2c: axxia: disable clks in case of failure in probe
i2c: octeon: thunderx: Limit register access retries
i2c: uniphier-f: fix misdetection of incomplete STOP condition
gpio: pca953x: variable 'id' was used twice
i2c: i801: Add support for Kaby Lake PCH-H
gpio: pca953x: fix an incorrect lockdep warning
i2c: add a warning to i2c_adapter_depth()
lockdep: make MAX_LOCKDEP_SUBCLASSES unconditionally visible
i2c: export i2c_adapter_depth()
i2c: rk3x: Fix variable 'min_total_ns' unused warning
i2c: rk3x: Fix sparse warning
i2c / ACPI: Do not touch an I2C device if it belongs to another adapter
i2c: octeon: Fix high-level controller status check
i2c: octeon: Avoid sending STOP during recovery
i2c: octeon: Fix set SCL recovery function
i2c: rcar: add support for r8a7796 (R-Car M3-W)
i2c: imx: make bus recovery through pinctrl optional
i2c: meson: add gxbb compatible string
i2c: uniphier-f: set the adapter to master mode when probing
i2c: uniphier-f: avoid WARN_ON() of clk_disable() in failure path
...
The core will do this for us now.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This fixes the below warnings
drivers/i2c/busses/i2c-cadence.c:164: warning: No description found for parameter 'dev'
drivers/i2c/busses/i2c-cadence.c:826: warning: No description found for parameter 'dev'
drivers/i2c/busses/i2c-cadence.c:826: warning: Excess function parameter '_dev' description in 'cdns_i2c_runtime_suspend'
drivers/i2c/busses/i2c-cadence.c:844: warning: No description found for parameter 'dev'
drivers/i2c/busses/i2c-cadence.c:844: warning: Excess function parameter '_dev' description in 'cdns_i2c_runtime_resume'
while at it also update the cdns_i2c_clear_bus_hold
and the runtime function update.
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The suspended flag is a flag holding the device's PM status.
The runtime framework does that for us.
Use pm_runtime_suspended call instead.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently the clocks are enabled at probe and disabled at remove.
Which keeps the clocks enabled even if no transaction is going on.
This patch enables the clocks at the start of transfer and disables
after it.
Also adapts to runtime pm.
converts dev pm to const to silence a checkpatch warning.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The owner of the adapter is missing, while this driver is tristate.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cadence 1.0 version has bugs which have been fixed in the cadence 1.4 version.
This patch removes the quirks present in the driver for cadence 1.4 version.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
[wsa: fixed indentation issues in r1p10_i2c_def]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
return type of wait_for_completion_timeout is unsigned long not int. The
return variable is renamed to make the timeout condition clearly readable
and the type adjusted to unsigned long.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cadence I2C controller has the following bugs:
- completion indication is not given to the driver at the end of
a read/receive transfer with HOLD bit set.
- Invalid read transaction are generated on the bus when HW timeout
condition occurs with HOLD bit set.
As a result of the above, if a set of messages to be transferred with
repeated start includes any message following a read message,
completion is never indicated and timeout occurs.
Hence a check is implemented to return -EOPNOTSUPP for such sequences.
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: Vishnu Motghare <vishnum@xilinx.com>
[wsa: fixed some whitespaces]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The I2C controller sends a NACK to the slave when transfer size register
reaches zero, irrespective of the hold bit. So, in order to handle transfers
greater than 252 bytes, the transfer size register has to be maintained at a
value >= 1. This patch implements the same.
The interrupt status is cleared at the beginning of the isr instead of
the end, to avoid missing any interrupts.
Signed-off-by: Harini Katakam <harinik@xilinx.com>
[wsa: added braces around else branch]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
Cadence I2C controller has bug wherein it generates invalid read transactions
after timeout in master receiver mode. This driver does not use the HW
timeout and this interrupt is disabled but the feature itself cannot be
disabled. Hence, this patch writes the maximum value (0xFF) to this register.
This is one of the workarounds to this bug and it will not avoid the issue
completely but reduces the chances of error.
Signed-off-by: Vishnu Motghare <vishnum@xilinx.com>
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Add a driver for the Cadence I2C controller. This controller is for
example found in Xilinx Zynq.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Lars-Peter Clausen