With the following commit:
4bc9f92e64 ("x86/efi-bgrt: Use efi_mem_reserve() to avoid copying image data")
... efi_bgrt_init() calls into the memblock allocator through
efi_mem_reserve() => efi_arch_mem_reserve() *after* mm_init() has been called.
Indeed, KASAN reports a bad read access later on in efi_free_boot_services():
BUG: KASAN: use-after-free in efi_free_boot_services+0xae/0x24c
at addr ffff88022de12740
Read of size 4 by task swapper/0/0
page:ffffea0008b78480 count:0 mapcount:-127
mapping: (null) index:0x1 flags: 0x5fff8000000000()
[...]
Call Trace:
dump_stack+0x68/0x9f
kasan_report_error+0x4c8/0x500
kasan_report+0x58/0x60
__asan_load4+0x61/0x80
efi_free_boot_services+0xae/0x24c
start_kernel+0x527/0x562
x86_64_start_reservations+0x24/0x26
x86_64_start_kernel+0x157/0x17a
start_cpu+0x5/0x14
The instruction at the given address is the first read from the memmap's
memory, i.e. the read of md->type in efi_free_boot_services().
Note that the writes earlier in efi_arch_mem_reserve() don't splat because
they're done through early_memremap()ed addresses.
So, after memblock is gone, allocations should be done through the "normal"
page allocator. Introduce a helper, efi_memmap_alloc() for this. Use
it from efi_arch_mem_reserve(), efi_free_boot_services() and, for the sake
of consistency, from efi_fake_memmap() as well.
Note that for the latter, the memmap allocations cease to be page aligned.
This isn't needed though.
Tested-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Nicolai Stange <nicstange@gmail.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: <stable@vger.kernel.org> # v4.9
Cc: Dave Young <dyoung@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Mika Penttilä <mika.penttila@nextfour.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Fixes: 4bc9f92e64 ("x86/efi-bgrt: Use efi_mem_reserve() to avoid copying image data")
Link: http://lkml.kernel.org/r/20170105125130.2815-1-nicstange@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
As reported by James Morse, the current libstub code involving the
annotated memory map only works somewhat correctly by accident, due
to the fact that a pool allocation happens to be reused immediately,
retaining its former contents on most implementations of the
UEFI boot services.
Instead of juggling memory maps, which makes the code more complex than
it needs to be, simply put placeholder values into the FDT for the memory
map parameters, and only write the actual values after ExitBootServices()
has been called.
Reported-by: James Morse <james.morse@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: <stable@vger.kernel.org>
Cc: Jeffrey Hugo <jhugo@codeaurora.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-efi@vger.kernel.org
Fixes: ed9cc156c4 ("efi/libstub: Use efi_exit_boot_services() in FDT")
Link: http://lkml.kernel.org/r/1482587963-20183-2-git-send-email-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit 4fd06960f1 ("Use the new x86 setup code for i386") introduced a
reference to the make variable LINUX_INCLUDE. That reference got moved
around a bit and copied twice and now there are three references to it.
There has never been a definition of that variable. (Presumably that is
because it started out as a mistyped reference to LINUXINCLUDE.) So this
reference has always been an empty string. Let's remove it before it
spreads any further.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
- struct thread_info moved off-stack (also touching
include/linux/thread_info.h and include/linux/restart_block.h)
- cpus_have_cap() reworked to avoid __builtin_constant_p() for static
key use (also touching drivers/irqchip/irq-gic-v3.c)
- Uprobes support (currently only for native 64-bit tasks)
- Emulation of kernel Privileged Access Never (PAN) using TTBR0_EL1
switching to a reserved page table
- CPU capacity information passing via DT or sysfs (used by the
scheduler)
- Support for systems without FP/SIMD (IOW, kernel avoids touching these
registers; there is no soft-float ABI, nor kernel emulation for
AArch64 FP/SIMD)
- Handling of hardware watchpoint with unaligned addresses, varied
lengths and offsets from base
- Use of the page table contiguous hint for kernel mappings
- Hugetlb fixes for sizes involving the contiguous hint
- Remove unnecessary I-cache invalidation in flush_cache_range()
- CNTHCTL_EL2 access fix for CPUs with VHE support (ARMv8.1)
- Boot-time checks for writable+executable kernel mappings
- Simplify asm/opcodes.h and avoid including the 32-bit ARM counterpart
and make the arm64 kernel headers self-consistent (Xen headers patch
merged separately)
- Workaround for broken .inst support in certain binutils versions
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8Uk9
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
- struct thread_info moved off-stack (also touching
include/linux/thread_info.h and include/linux/restart_block.h)
- cpus_have_cap() reworked to avoid __builtin_constant_p() for static
key use (also touching drivers/irqchip/irq-gic-v3.c)
- uprobes support (currently only for native 64-bit tasks)
- Emulation of kernel Privileged Access Never (PAN) using TTBR0_EL1
switching to a reserved page table
- CPU capacity information passing via DT or sysfs (used by the
scheduler)
- support for systems without FP/SIMD (IOW, kernel avoids touching
these registers; there is no soft-float ABI, nor kernel emulation for
AArch64 FP/SIMD)
- handling of hardware watchpoint with unaligned addresses, varied
lengths and offsets from base
- use of the page table contiguous hint for kernel mappings
- hugetlb fixes for sizes involving the contiguous hint
- remove unnecessary I-cache invalidation in flush_cache_range()
- CNTHCTL_EL2 access fix for CPUs with VHE support (ARMv8.1)
- boot-time checks for writable+executable kernel mappings
- simplify asm/opcodes.h and avoid including the 32-bit ARM counterpart
and make the arm64 kernel headers self-consistent (Xen headers patch
merged separately)
- Workaround for broken .inst support in certain binutils versions
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (60 commits)
arm64: Disable PAN on uaccess_enable()
arm64: Work around broken .inst when defective gas is detected
arm64: Add detection code for broken .inst support in binutils
arm64: Remove reference to asm/opcodes.h
arm64: Get rid of asm/opcodes.h
arm64: smp: Prevent raw_smp_processor_id() recursion
arm64: head.S: Fix CNTHCTL_EL2 access on VHE system
arm64: Remove I-cache invalidation from flush_cache_range()
arm64: Enable HIBERNATION in defconfig
arm64: Enable CONFIG_ARM64_SW_TTBR0_PAN
arm64: xen: Enable user access before a privcmd hvc call
arm64: Handle faults caused by inadvertent user access with PAN enabled
arm64: Disable TTBR0_EL1 during normal kernel execution
arm64: Introduce uaccess_{disable,enable} functionality based on TTBR0_EL1
arm64: Factor out TTBR0_EL1 post-update workaround into a specific asm macro
arm64: Factor out PAN enabling/disabling into separate uaccess_* macros
arm64: Update the synchronous external abort fault description
selftests: arm64: add test for unaligned/inexact watchpoint handling
arm64: Allow hw watchpoint of length 3,5,6 and 7
arm64: hw_breakpoint: Handle inexact watchpoint addresses
...
The UEFI stub executes in the context of the firmware, which identity
maps the available system RAM, which implies that only memory below
4 GB can be used for allocations on 32-bit architectures, even on [L]PAE
capable hardware.
So ignore any reported memory above 4 GB in efi_random_alloc(). This
also fixes a reported build problem on ARM under -Os, where the 64-bit
logical shift relies on a software routine that the ARM decompressor does
not provide.
A second [minor] issue is also fixed, where the '+ 1' is moved out of
the shift, where it belongs: the reason for its presence is that a
memory region where start == end should count as a single slot, given
that 'end' takes the desired size and alignment of the allocation into
account.
To clarify the code in this regard, rename start/end to 'first_slot' and
'last_slot', respectively, and introduce 'region_end' to describe the
last usable address of the current region.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/1480010543-25709-2-git-send-email-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Apple's EFI drivers supply device properties which are needed to support
Macs optimally. They contain vital information which cannot be obtained
any other way (e.g. Thunderbolt Device ROM). They're also used to convey
the current device state so that OS drivers can pick up where EFI
drivers left (e.g. GPU mode setting).
There's an EFI driver dubbed "AAPL,PathProperties" which implements a
per-device key/value store. Other EFI drivers populate it using a custom
protocol. The macOS bootloader /System/Library/CoreServices/boot.efi
retrieves the properties with the same protocol. The kernel extension
AppleACPIPlatform.kext subsequently merges them into the I/O Kit
registry (see ioreg(8)) where they can be queried by other kernel
extensions and user space.
This commit extends the efistub to retrieve the device properties before
ExitBootServices is called. It assigns them to devices in an fs_initcall
so that they can be queried with the API in <linux/property.h>.
Note that the device properties will only be available if the kernel is
booted with the efistub. Distros should adjust their installers to
always use the efistub on Macs. grub with the "linux" directive will not
work unless the functionality of this commit is duplicated in grub.
(The "linuxefi" directive should work but is not included upstream as of
this writing.)
The custom protocol has GUID 91BD12FE-F6C3-44FB-A5B7-5122AB303AE0 and
looks like this:
typedef struct {
unsigned long version; /* 0x10000 */
efi_status_t (*get) (
IN struct apple_properties_protocol *this,
IN struct efi_dev_path *device,
IN efi_char16_t *property_name,
OUT void *buffer,
IN OUT u32 *buffer_len);
/* EFI_SUCCESS, EFI_NOT_FOUND, EFI_BUFFER_TOO_SMALL */
efi_status_t (*set) (
IN struct apple_properties_protocol *this,
IN struct efi_dev_path *device,
IN efi_char16_t *property_name,
IN void *property_value,
IN u32 property_value_len);
/* allocates copies of property name and value */
/* EFI_SUCCESS, EFI_OUT_OF_RESOURCES */
efi_status_t (*del) (
IN struct apple_properties_protocol *this,
IN struct efi_dev_path *device,
IN efi_char16_t *property_name);
/* EFI_SUCCESS, EFI_NOT_FOUND */
efi_status_t (*get_all) (
IN struct apple_properties_protocol *this,
OUT void *buffer,
IN OUT u32 *buffer_len);
/* EFI_SUCCESS, EFI_BUFFER_TOO_SMALL */
} apple_properties_protocol;
Thanks to Pedro Vilaça for this blog post which was helpful in reverse
engineering Apple's EFI drivers and bootloader:
https://reverse.put.as/2016/06/25/apple-efi-firmware-passwords-and-the-scbo-myth/
If someone at Apple is reading this, please note there's a memory leak
in your implementation of the del() function as the property struct is
freed but the name and value allocations are not.
Neither the macOS bootloader nor Apple's EFI drivers check the protocol
version, but we do to avoid breakage if it's ever changed. It's been the
same since at least OS X 10.6 (2009).
The get_all() function conveniently fills a buffer with all properties
in marshalled form which can be passed to the kernel as a setup_data
payload. The number of device properties is dynamic and can change
between a first invocation of get_all() (to determine the buffer size)
and a second invocation (to retrieve the actual buffer), hence the
peculiar loop which does not finish until the buffer size settles.
The macOS bootloader does the same.
The setup_data payload is later on unmarshalled in an fs_initcall. The
idea is that most buses instantiate devices in "subsys" initcall level
and drivers are usually bound to these devices in "device" initcall
level, so we assign the properties in-between, i.e. in "fs" initcall
level.
This assumes that devices to which properties pertain are instantiated
from a "subsys" initcall or earlier. That should always be the case
since on macOS, AppleACPIPlatformExpert::matchEFIDevicePath() only
supports ACPI and PCI nodes and we've fully scanned those buses during
"subsys" initcall level.
The second assumption is that properties are only needed from a "device"
initcall or later. Seems reasonable to me, but should this ever not work
out, an alternative approach would be to store the property sets e.g. in
a btree early during boot. Then whenever device_add() is called, an EFI
Device Path would have to be constructed for the newly added device,
and looked up in the btree. That way, the property set could be assigned
to the device immediately on instantiation. And this would also work for
devices instantiated in a deferred fashion. It seems like this approach
would be more complicated and require more code. That doesn't seem
justified without a specific use case.
For comparison, the strategy on macOS is to assign properties to objects
in the ACPI namespace (AppleACPIPlatformExpert::mergeEFIProperties()).
That approach is definitely wrong as it fails for devices not present in
the namespace: The NHI EFI driver supplies properties for attached
Thunderbolt devices, yet on Macs with Thunderbolt 1 only one device
level behind the host controller is described in the namespace.
Consequently macOS cannot assign properties for chained devices. With
Thunderbolt 2 they started to describe three device levels behind host
controllers in the namespace but this grossly inflates the SSDT and
still fails if the user daisy-chained more than three devices.
We copy the property names and values from the setup_data payload to
swappable virtual memory and afterwards make the payload available to
the page allocator. This is just for the sake of good housekeeping, it
wouldn't occupy a meaningful amount of physical memory (4444 bytes on my
machine). Only the payload is freed, not the setup_data header since
otherwise we'd break the list linkage and we cannot safely update the
predecessor's ->next link because there's no locking for the list.
The payload is currently not passed on to kexec'ed kernels, same for PCI
ROMs retrieved by setup_efi_pci(). This can be added later if there is
demand by amending setup_efi_state(). The payload can then no longer be
made available to the page allocator of course.
Tested-by: Lukas Wunner <lukas@wunner.de> [MacBookPro9,1]
Tested-by: Pierre Moreau <pierre.morrow@free.fr> [MacBookPro11,3]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Andreas Noever <andreas.noever@gmail.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Pedro Vilaça <reverser@put.as>
Cc: Peter Jones <pjones@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: grub-devel@gnu.org
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20161112213237.8804-9-matt@codeblueprint.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We're about to extended the efistub to retrieve device properties from
EFI on Apple Macs. The properties use EFI Device Paths to indicate the
device they belong to. This commit adds a parser which, given an EFI
Device Path, locates the corresponding struct device and returns a
reference to it.
Initially only ACPI and PCI Device Path nodes are supported, these are
the only types needed for Apple device properties (the corresponding
macOS function AppleACPIPlatformExpert::matchEFIDevicePath() does not
support any others). Further node types can be added with little to
moderate effort.
Apple device properties is currently the only use case of this parser,
but Peter Jones intends to use it to match up devices with the
ConInDev/ConOutDev/ErrOutDev variables and add sysfs attributes to these
devices to say the hardware supports using them as console. Thus,
make this parser a separate component which can be selected with config
option EFI_DEV_PATH_PARSER. It can in principle be compiled as a module
if acpi_get_first_physical_node() and acpi_bus_type are exported (and
efi_get_device_by_path() itself is exported).
The dependency on CONFIG_ACPI is needed for acpi_match_device_ids().
It can be removed if an empty inline stub is added for that function.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Andreas Noever <andreas.noever@gmail.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Jones <pjones@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20161112213237.8804-7-matt@codeblueprint.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Invoke the EFI_RNG_PROTOCOL protocol in the context of the stub and
install the Linux-specific RNG seed UEFI config table. This will be
picked up by the EFI routines in the core kernel to seed the kernel
entropy pool.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20161112213237.8804-6-matt@codeblueprint.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Make random.c build for ARM by moving the fallback definition of
EFI_ALLOC_ALIGN to efistub.h, and replacing a division by a value
we know to be a power of 2 with a right shift (this is required since
ARM does not have any integer division helper routines in its decompressor)
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20161112213237.8804-5-matt@codeblueprint.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Specify a Linux specific UEFI configuration table that carries some
random bits, and use the contents during early boot to seed the kernel's
random number generator. This allows much strong random numbers to be
generated early on.
The entropy is fed to the kernel using add_device_randomness(), which is
documented as being appropriate for being called very early.
Since UEFI configuration tables may also be consumed by kexec'd kernels,
register a reboot notifier that updates the seed in the table.
Note that the config table could be generated by the EFI stub or by any
other UEFI driver or application (e.g., GRUB), but the random seed table
GUID and the associated functionality should be considered an internal
kernel interface (unless it is promoted to ABI later on)
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20161112213237.8804-4-matt@codeblueprint.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Adjust the size used in calculations to match the actual size of allocation
that will be performed based on EFI size/alignment constraints.
efi_high_alloc() and efi_low_alloc() use the passed size in bytes directly
to find space in the memory map for the allocation, rather than the actual
allocation size that has been adjusted for size and alignment constraints.
This results in failed allocations and retries in efi_high_alloc(). The
same error is present in efi_low_alloc(), although failure will only happen
if the lowest memory block is small.
Also use EFI_PAGE_SIZE consistently and remove use of EFI_PAGE_SHIFT to
calculate page size.
Signed-off-by: Roy Franz <roy.franz@hpe.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20161112213237.8804-2-matt@codeblueprint.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
ptdump_register currently initializes a set of page table information and
registers debugfs. There are uses for the ptdump option without wanting the
debugfs options. Split this out to make it a separate option.
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
When building the ARM kernel with CONFIG_EFI=y, the following build
error may occur when using a less recent version of binutils (2.23 or
older):
STUBCPY drivers/firmware/efi/libstub/lib-sort.stub.o
00000000 R_ARM_ABS32 sort
00000004 R_ARM_ABS32 __ksymtab_strings
drivers/firmware/efi/libstub/lib-sort.stub.o: absolute symbol references not allowed in the EFI stub
(and when building with debug symbols, the list above is much longer, and
contains all the internal references between the .debug sections and the
actual code)
This issue is caused by the fact that objcopy v2.23 or earlier does not
support wildcards in its -R and -j options, which means the following
line from the Makefile:
STUBCOPY_FLAGS-y := -R .debug* -R *ksymtab* -R *kcrctab*
fails to take effect, leaving harmless absolute relocations in the binary
that are indistinguishable from relocations that may cause crashes at
runtime due to the fact that these relocations are resolved at link time
using the virtual address of the kernel, which is always different from
the address at which the EFI firmware loads and invokes the stub.
So, as a workaround, disable debug symbols explicitly when building the
stub for ARM, and strip the ksymtab and kcrctab symbols for the only
exported symbol we currently reuse in the stub, which is 'sort'.
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/1476805991-7160-2-git-send-email-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Fix coccicheck warning which recommends to use memdup_user().
This patch fixes the following coccicheck warnings:
drivers/firmware/efi/test/efi_test.c:269:8-15: WARNING opportunity for memdup_user
Signed-off-by: Ivan Hu <ivan.hu@canonical.com>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20161018143318.15673-7-matt@codeblueprint.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Mike Galbraith reported that his machine started rebooting during boot
after,
commit 8e80632fb2 ("efi/esrt: Use efi_mem_reserve() and avoid a kmalloc()")
The ESRT table on his machine is 56 bytes and at no point in the
efi_arch_mem_reserve() call path is that size rounded up to
EFI_PAGE_SIZE, nor is the start address on an EFI_PAGE_SIZE boundary.
Since the EFI memory map only deals with whole pages, inserting an EFI
memory region with 56 bytes results in a new entry covering zero
pages, and completely screws up the calculations for the old regions
that were trimmed.
Round all sizes upwards, and start addresses downwards, to the nearest
EFI_PAGE_SIZE boundary.
Additionally, efi_memmap_insert() expects the mem::range::end value to
be one less than the end address for the region.
Reported-by: Mike Galbraith <umgwanakikbuti@gmail.com>
Reported-by: Mike Krinkin <krinkin.m.u@gmail.com>
Tested-by: Mike Krinkin <krinkin.m.u@gmail.com>
Cc: Peter Jones <pjones@redhat.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
and allow drivers to permanently reserve EFI boot services regions
on x86, as well as ARM/arm64 - Matt Fleming
* Add ARM support for the EFI esrt driver - Ard Biesheuvel
* Make the EFI runtime services and efivar API interruptible by
swapping spinlocks for semaphores - Sylvain Chouleur
* Provide the EFI identity mapping for kexec which allows kexec to
work on SGI/UV platforms with requiring the "noefi" kernel command
line parameter - Alex Thorlton
* Add debugfs node to dump EFI page tables on arm64 - Ard Biesheuvel
* Merge the EFI test driver being carried out of tree until now in
the FWTS project - Ivan Hu
* Expand the list of flags for classifying EFI regions as "RAM" on
arm64 so we align with the UEFI spec - Ard Biesheuvel
* Optimise out the EFI mixed mode if it's unsupported (CONFIG_X86_32)
or disabled (CONFIG_EFI_MIXED=n) and switch the early EFI boot
services function table for direct calls, alleviating us from
having to maintain the custom function table - Lukas Wunner
* Miscellaneous cleanups and fixes
-----BEGIN PGP SIGNATURE-----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=G7L6
-----END PGP SIGNATURE-----
Merge tag 'efi-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mfleming/efi into efi/core
Pull EFI updates from Matt Fleming:
"* Refactor the EFI memory map code into architecture neutral files
and allow drivers to permanently reserve EFI boot services regions
on x86, as well as ARM/arm64 - Matt Fleming
* Add ARM support for the EFI esrt driver - Ard Biesheuvel
* Make the EFI runtime services and efivar API interruptible by
swapping spinlocks for semaphores - Sylvain Chouleur
* Provide the EFI identity mapping for kexec which allows kexec to
work on SGI/UV platforms with requiring the "noefi" kernel command
line parameter - Alex Thorlton
* Add debugfs node to dump EFI page tables on arm64 - Ard Biesheuvel
* Merge the EFI test driver being carried out of tree until now in
the FWTS project - Ivan Hu
* Expand the list of flags for classifying EFI regions as "RAM" on
arm64 so we align with the UEFI spec - Ard Biesheuvel
* Optimise out the EFI mixed mode if it's unsupported (CONFIG_X86_32)
or disabled (CONFIG_EFI_MIXED=n) and switch the early EFI boot
services function table for direct calls, alleviating us from
having to maintain the custom function table - Lukas Wunner
* Miscellaneous cleanups and fixes"
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Currently, memory regions are only recorded in the memblock memory table
if they have the EFI_MEMORY_WB memory type attribute set. In case the
region is of a reserved type, it is also marked as MEMBLOCK_NOMAP, which
will leave it out of the linear mapping.
However, memory regions may legally have the EFI_MEMORY_WT or EFI_MEMORY_WC
attributes set, and the EFI_MEMORY_WB cleared, in which case the region in
question is obviously backed by normal memory, but is not recorded in the
memblock memory table at all. Since it would be useful to be able to
identify any UEFI reported memory region using memblock_is_memory(), it
makes sense to add all memory to the memblock memory table, and simply mark
it as MEMBLOCK_NOMAP if it lacks the EFI_MEMORY_WB attribute.
While implementing this, let's refactor the code slightly to make it easier
to understand: replace is_normal_ram() with is_memory(), and make it return
true for each region that has any of the WB|WT|WC bits set. (This follows
the AArch64 bindings in the UEFI spec, which state that those are the
attributes that map to normal memory)
Also, replace is_reserve_region() with is_usable_memory(), and only invoke
it if the region in question was identified as memory by is_memory() in the
first place. The net result is the same (only reserved regions that are
backed by memory end up in the memblock memory table with the MEMBLOCK_NOMAP
flag set) but carried out in a more straightforward way.
Finally, we remove the trailing asterisk in the EFI debug output. Keeping it
clutters the code, and it serves no real purpose now that we no longer
temporarily reserve BootServices code and data regions like we did in the
early days of EFI support on arm64 Linux (which it inherited from the x86
implementation)
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Tested-by: James Morse <james.morse@arm.com>
Reviewed-by: James Morse <james.morse@arm.com>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
This driver is used by the Firmware Test Suite (FWTS) for testing the UEFI
runtime interfaces readiness of the firmware.
This driver exports UEFI runtime service interfaces into userspace,
which allows to use and test UEFI runtime services provided by the
firmware.
This driver uses the efi.<service> function pointers directly instead of
going through the efivar API to allow for direct testing of the UEFI
runtime service interfaces provided by the firmware.
Details for FWTS are available from,
<https://wiki.ubuntu.com/FirmwareTestSuite>
Signed-off-by: Ivan Hu <ivan.hu@canonical.com>
Cc: joeyli <jlee@suse.com>
Cc: Ricardo Neri <ricardo.neri-calderon@linux.intel.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Register the debugfs node 'efi_page_tables' to allow the UEFI runtime
page tables to be inspected. Note that ARM does not have 'asm/ptdump.h'
[yet] so for now, this is arm64 only.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
The purpose of the efi_runtime_lock is to prevent concurrent calls into
the firmware. There is no need to use spinlocks here, as long as we ensure
that runtime service invocations from an atomic context (i.e., EFI pstore)
cannot block.
So use a semaphore instead, and use down_trylock() in the nonblocking case.
We don't use a mutex here because the mutex_trylock() function must not
be called from interrupt context, whereas the down_trylock() can.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Sylvain Chouleur <sylvain.chouleur@gmail.com>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
All efivars operations are protected by a spinlock which prevents
interruptions and preemption. This is too restricted, we just need a
lock preventing concurrency.
The idea is to use a semaphore of count 1 and to have two ways of
locking, depending on the context:
- In interrupt context, we call down_trylock(), if it fails we return
an error
- In normal context, we call down_interruptible()
We don't use a mutex here because the mutex_trylock() function must not
be called from interrupt context, whereas the down_trylock() can.
Signed-off-by: Sylvain Chouleur <sylvain.chouleur@intel.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Sylvain Chouleur <sylvain.chouleur@gmail.com>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
This patch replaces the spinlock in the efivars struct with a single lock
for the whole vars.c file. The goal of this lock is to protect concurrent
calls to efi variable services, registering and unregistering. This allows
us to register new efivars operations without having in-progress call.
Signed-off-by: Sylvain Chouleur <sylvain.chouleur@intel.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Sylvain Chouleur <sylvain.chouleur@gmail.com>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
ESRT support is built by default for all architectures that define
CONFIG_EFI. However, this support was not wired up yet for ARM/arm64,
since efi_esrt_init() was never called. So add the missing call.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Peter Jones <pjones@redhat.com>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
On ARM and arm64, ioremap() and memremap() are not interchangeable like
on x86, and the use of ioremap() on ordinary RAM is typically flagged
as an error if the memory region being mapped is also covered by the
linear mapping, since that would lead to aliases with conflicting
cacheability attributes.
Since what we are dealing with is not an I/O region with side effects,
using ioremap() here is arguably incorrect anyway, so let's replace
it with memremap() instead.
Acked-by: Peter Jones <pjones@redhat.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
We can use the new efi_mem_reserve() API to mark the ESRT table as
reserved forever and save ourselves the trouble of copying the data
out into a kmalloc buffer.
The added advantage is that now the ESRT driver will work across
kexec reboot.
Tested-by: Dave Young <dyoung@redhat.com> [kexec/kdump]
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> [arm]
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Peter Jones <pjones@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Now that efi.memmap is available all of the time there's no need to
allocate and build a separate copy of the EFI memory map.
Furthermore, efi.memmap contains boot services regions but only those
regions that have been reserved via efi_mem_reserve(). Using
efi.memmap allows us to pass boot services across kexec reboot so that
the ESRT and BGRT drivers will now work.
Tested-by: Dave Young <dyoung@redhat.com> [kexec/kdump]
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> [arm]
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Peter Jones <pjones@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Today, it is not possible for drivers to reserve EFI boot services for
access after efi_free_boot_services() has been called on x86. For
ARM/arm64 it can be done simply by calling memblock_reserve().
Having this ability for all three architectures is desirable for a
couple of reasons,
1) It saves drivers copying data out of those regions
2) kexec reboot can now make use of things like ESRT
Instead of using the standard memblock_reserve() which is insufficient
to reserve the region on x86 (see efi_reserve_boot_services()), a new
API is introduced in this patch; efi_mem_reserve().
efi.memmap now always represents which EFI memory regions are
available. On x86 the EFI boot services regions that have not been
reserved via efi_mem_reserve() will be removed from efi.memmap during
efi_free_boot_services().
This has implications for kexec, since it is not possible for a newly
kexec'd kernel to access the same boot services regions that the
initial boot kernel had access to unless they are reserved by every
kexec kernel in the chain.
Tested-by: Dave Young <dyoung@redhat.com> [kexec/kdump]
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> [arm]
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Peter Jones <pjones@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
While efi_memmap_init_{early,late}() exist for architecture code to
install memory maps from firmware data and for the virtual memory
regions respectively, drivers don't care which stage of the boot we're
at and just want to swap the existing memmap for a modified one.
efi_memmap_install() abstracts the details of how the new memory map
should be mapped and the existing one unmapped.
Tested-by: Dave Young <dyoung@redhat.com> [kexec/kdump]
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> [arm]
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Peter Jones <pjones@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Also move the functions from the EFI fake mem driver since future
patches will require access to the memmap insertion code even if
CONFIG_EFI_FAKE_MEM isn't enabled.
This will be useful when we need to build custom EFI memory maps to
allow drivers to mark regions as reserved.
Tested-by: Dave Young <dyoung@redhat.com> [kexec/kdump]
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> [arm]
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Peter Jones <pjones@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
There is a whole load of generic EFI memory map code inside of the
fake_mem driver which is better suited to being grouped with the rest
of the generic EFI code for manipulating EFI memory maps.
In preparation for that, this patch refactors the core code, so that
it's possible to move entire functions later.
Tested-by: Dave Young <dyoung@redhat.com> [kexec/kdump]
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> [arm]
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Peter Jones <pjones@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Drivers need a way to access the EFI memory map at runtime. ARM and
arm64 currently provide this by remapping the EFI memory map into the
vmalloc space before setting up the EFI virtual mappings.
x86 does not provide this functionality which has resulted in the code
in efi_mem_desc_lookup() where it will manually map individual EFI
memmap entries if the memmap has already been torn down on x86,
/*
* If a driver calls this after efi_free_boot_services,
* ->map will be NULL, and the target may also not be mapped.
* So just always get our own virtual map on the CPU.
*
*/
md = early_memremap(p, sizeof (*md));
There isn't a good reason for not providing a permanent EFI memory map
for runtime queries, especially since the EFI regions are not mapped
into the standard kernel page tables.
Tested-by: Dave Young <dyoung@redhat.com> [kexec/kdump]
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> [arm]
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Peter Jones <pjones@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Every EFI architecture apart from ia64 needs to setup the EFI memory
map at efi.memmap, and the code for doing that is essentially the same
across all implementations. Therefore, it makes sense to factor this
out into the common code under drivers/firmware/efi/.
The only slight variation is the data structure out of which we pull
the initial memory map information, such as physical address, memory
descriptor size and version, etc. We can address this by passing a
generic data structure (struct efi_memory_map_data) as the argument to
efi_memmap_init_early() which contains the minimum info required for
initialising the memory map.
In the process, this patch also fixes a few undesirable implementation
differences:
- ARM and arm64 were failing to clear the EFI_MEMMAP bit when
unmapping the early EFI memory map. EFI_MEMMAP indicates whether
the EFI memory map is mapped (not the regions contained within) and
can be traversed. It's more correct to set the bit as soon as we
memremap() the passed in EFI memmap.
- Rename efi_unmmap_memmap() to efi_memmap_unmap() to adhere to the
regular naming scheme.
This patch also uses a read-write mapping for the memory map instead
of the read-only mapping currently used on ARM and arm64. x86 needs
the ability to update the memory map in-place when assigning virtual
addresses to regions (efi_map_region()) and tagging regions when
reserving boot services (efi_reserve_boot_services()).
There's no way for the generic fake_mem code to know which mapping to
use without introducing some arch-specific constant/hook, so just use
read-write since read-only is of dubious value for the EFI memory map.
Tested-by: Dave Young <dyoung@redhat.com> [kexec/kdump]
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> [arm]
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Peter Jones <pjones@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Both efi_find_mirror() and efi_fake_memmap() really want to know
whether the EFI memory map is available, not just whether the machine
was booted using EFI. efi_fake_memmap() even has a check for
EFI_MEMMAP at the start of the function.
Since we've already got other code that has this dependency, merge
everything under one if() conditional, and remove the now superfluous
check from efi_fake_memmap().
Tested-by: Dave Young <dyoung@redhat.com> [kexec/kdump]
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> [arm]
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Taku Izumi <izumi.taku@jp.fujitsu.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Xishi Qiu <qiuxishi@huawei.com>
Cc: Kamezawa Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
This patch adds new PSTORE_FLAGS for each pstore type so that they can
be enabled separately. This is a preparation for ongoing virtio-pstore
work to support those types flexibly.
The PSTORE_FLAGS_FRAGILE is changed to PSTORE_FLAGS_DMESG to preserve the
original behavior.
Cc: Anton Vorontsov <anton@enomsg.org>
Cc: Colin Cross <ccross@android.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Len Brown <lenb@kernel.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: linux-acpi@vger.kernel.org
Cc: linux-efi@vger.kernel.org
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
[kees: retained "FRAGILE" for now to make merges easier]
Signed-off-by: Kees Cook <keescook@chromium.org>
The FDT code directly calls ExitBootServices. This is inadvisable as the
UEFI spec details a complex set of errors, race conditions, and API
interactions that the caller of ExitBootServices must get correct. The
FDT code does not handle EFI_INVALID_PARAMETER as required by the spec,
which causes intermittent boot failures on the Qualcomm Technologies
QDF2432. Call the efi_exit_boot_services() helper intead, which handles
the EFI_INVALID_PARAMETER scenario properly.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
The spec allows ExitBootServices to fail with EFI_INVALID_PARAMETER if a
race condition has occurred where the EFI has updated the memory map after
the stub grabbed a reference to the map. The spec defines a retry
proceedure with specific requirements to handle this scenario.
This scenario was previously observed on x86 - commit d3768d885c ("x86,
efi: retry ExitBootServices() on failure") but the current fix is not spec
compliant and the scenario is now observed on the Qualcomm Technologies
QDF2432 via the FDT stub which does not handle the error and thus causes
boot failures. The user will notice the boot failure as the kernel is not
executed and the system may drop back to a UEFI shell, but will be
unresponsive to input and the system will require a power cycle to recover.
Add a helper to the stub library that correctly adheres to the spec in the
case of EFI_INVALID_PARAMETER from ExitBootServices and can be universally
used across all stub implementations.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
efi_get_memory_map() allocates a buffer to store the memory map that it
retrieves. This buffer may need to be reused by the client after
ExitBootServices() is called, at which point allocations are not longer
permitted. To support this usecase, provide the allocated buffer size back
to the client, and allocate some additional headroom to account for any
reasonable growth in the map that is likely to happen between the call to
efi_get_memory_map() and the client reusing the buffer.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
of_get_flat_dt_subnode_by_name can return negative value in case of error.
Assigning the result to unsigned variable and checking if the variable
is lesser than zero is incorrect and always false.
The patch fixes it by using signed variable to check the result.
The problem has been detected using semantic patch
scripts/coccinelle/tests/unsigned_lesser_than_zero.cocci
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
According to UEFI 2.6 section 7.5.3, the capsule should be in contiguous
virtual memory and firmware may consume the capsule immediately. To
correctly implement this functionality, the kernel driver needs to vmap
the entire capsule at the time it is made available to firmware.
The virtual allocation of the capsule update has been changed from kmap,
which was only allocating the first page of the update, to vmap, and
allocates the entire data payload.
Signed-off-by: Austin Christ <austinwc@codeaurora.org>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Reviewed-by: Matt Fleming <matt@codeblueprint.co.uk>
Reviewed-by: Lee, Chun-Yi <jlee@suse.com>
Cc: <stable@vger.kernel.org> # v4.7
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Kweh Hock Leong <hock.leong.kweh@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/1470912120-22831-3-git-send-email-matt@codeblueprint.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
- ACPI support for guests on ARM platforms.
- Generic steal time support for arm and x86.
- Support cases where kernel cpu is not Xen VCPU number (e.g., if
in-guest kexec is used).
- Use the system workqueue instead of a custom workqueue in various
places.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXmLlrAAoJEFxbo/MsZsTRvRQH/1wOMF8BmlbZfR7H3qwDfjst
ApNifCiZE08xDtWBlwUaBFAQxyflQS9BBiNZDVK0sysIdXeOdpWV7V0ZjRoLL+xr
czsaaGXDcmXxJxApoMDVuT7FeP6rEk6LVAYRoHpVjJjMZGW3BbX1vZaMW4DXl2WM
9YNaF2Lj+rpc1f8iG31nUxwkpmcXFog6ct4tu7HiyCFT3hDkHt/a4ghuBdQItCkd
vqBa1pTpcGtQBhSmWzlylN/PV2+NKcRd+kGiwd09/O/rNzogTMCTTWeHKAtMpPYb
Cu6oSqJtlK5o0vtr0qyLSWEGIoyjE2gE92s0wN3iCzFY1PldqdsxUO622nIj+6o=
=G6q3
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.8-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen updates from David Vrabel:
"Features and fixes for 4.8-rc0:
- ACPI support for guests on ARM platforms.
- Generic steal time support for arm and x86.
- Support cases where kernel cpu is not Xen VCPU number (e.g., if
in-guest kexec is used).
- Use the system workqueue instead of a custom workqueue in various
places"
* tag 'for-linus-4.8-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: (47 commits)
xen: add static initialization of steal_clock op to xen_time_ops
xen/pvhvm: run xen_vcpu_setup() for the boot CPU
xen/evtchn: use xen_vcpu_id mapping
xen/events: fifo: use xen_vcpu_id mapping
xen/events: use xen_vcpu_id mapping in events_base
x86/xen: use xen_vcpu_id mapping when pointing vcpu_info to shared_info
x86/xen: use xen_vcpu_id mapping for HYPERVISOR_vcpu_op
xen: introduce xen_vcpu_id mapping
x86/acpi: store ACPI ids from MADT for future usage
x86/xen: update cpuid.h from Xen-4.7
xen/evtchn: add IOCTL_EVTCHN_RESTRICT
xen-blkback: really don't leak mode property
xen-blkback: constify instance of "struct attribute_group"
xen-blkfront: prefer xenbus_scanf() over xenbus_gather()
xen-blkback: prefer xenbus_scanf() over xenbus_gather()
xen: support runqueue steal time on xen
arm/xen: add support for vm_assist hypercall
xen: update xen headers
xen-pciback: drop superfluous variables
xen-pciback: short-circuit read path used for merging write values
...
- Support for ACPI SSDT overlays allowing Secondary System
Description Tables (SSDTs) to be loaded at any time from EFI
variables or via configfs (Octavian Purdila, Mika Westerberg).
- Support for the ACPI LPI (Low-Power Idle) feature introduced in
ACPI 6.0 and allowing processor idle states to be represented in
ACPI tables in a hierarchical way (with the help of Processor
Container objects) and support for ACPI idle states management
on ARM64, based on LPI (Sudeep Holla).
- General improvements of ACPI support for NUMA and ARM64 support
for ACPI-based NUMA (Hanjun Guo, David Daney, Robert Richter).
- General improvements of the ACPI table upgrade mechanism and
ARM64 support for that feature (Aleksey Makarov, Jon Masters).
- Support for the Boot Error Record Table (BERT) in APEI and
improvements of kernel messages printed by the error injection
code (Huang Ying, Borislav Petkov).
- New driver for the Intel Broxton WhiskeyCove PMIC operation
region and support for the REGS operation region on Broxton,
PMIC code cleanups (Bin Gao, Felipe Balbi, Paul Gortmaker).
- New driver for the power participant device which is part of the
Dynamic Power and Thermal Framework (DPTF) and DPTF-related code
reorganization (Srinivas Pandruvada).
- Support for the platform-initiated graceful shutdown feature
introduced in ACPI 6.1 (Prashanth Prakash).
- ACPI button driver update related to lid input events generated
automatically on initialization and system resume that have been
problematic for some time (Lv Zheng).
- ACPI EC driver cleanups (Lv Zheng).
- Documentation of the ACPICA release automation process and the
in-kernel ACPI AML debugger (Lv Zheng).
- New blacklist entry and two fixes for the ACPI backlight driver
(Alex Hung, Arvind Yadav, Ralf Gerbig).
- Cleanups of the ACPI pci_slot driver (Joe Perches, Paul Gortmaker).
- ACPI CPPC code changes to make it more robust against possible
defects in ACPI tables and new symbol definitions for PCC (Hoan
Tran).
- System reboot code modification to execute the ACPI _PTS (Prepare
To Sleep) method in addition to _TTS (Ocean He).
- ACPICA-related change to carry out lock ordering checks in ACPICA
if ACPICA debug is enabled in the kernel (Lv Zheng).
- Assorted minor fixes and cleanups (Andy Shevchenko, Baoquan He,
Bhaktipriya Shridhar, Paul Gortmaker, Rafael Wysocki).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=YwbM
-----END PGP SIGNATURE-----
Merge tag 'acpi-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"The new feaures here are the support for ACPI overlays (allowing ACPI
tables to be loaded at any time from EFI variables or via configfs)
and the LPI (Low-Power Idle) support. Also notable is the ACPI-based
NUMA support for ARM64.
Apart from that we have two new drivers, for the DPTF (Dynamic Power
and Thermal Framework) power participant device and for the Intel
Broxton WhiskeyCove PMIC, some more PMIC-related changes, support for
the Boot Error Record Table (BERT) in APEI and support for
platform-initiated graceful shutdown.
Plus two new pieces of documentation and usual assorted fixes and
cleanups in quite a few places.
Specifics:
- Support for ACPI SSDT overlays allowing Secondary System
Description Tables (SSDTs) to be loaded at any time from EFI
variables or via configfs (Octavian Purdila, Mika Westerberg).
- Support for the ACPI LPI (Low-Power Idle) feature introduced in
ACPI 6.0 and allowing processor idle states to be represented in
ACPI tables in a hierarchical way (with the help of Processor
Container objects) and support for ACPI idle states management on
ARM64, based on LPI (Sudeep Holla).
- General improvements of ACPI support for NUMA and ARM64 support for
ACPI-based NUMA (Hanjun Guo, David Daney, Robert Richter).
- General improvements of the ACPI table upgrade mechanism and ARM64
support for that feature (Aleksey Makarov, Jon Masters).
- Support for the Boot Error Record Table (BERT) in APEI and
improvements of kernel messages printed by the error injection code
(Huang Ying, Borislav Petkov).
- New driver for the Intel Broxton WhiskeyCove PMIC operation region
and support for the REGS operation region on Broxton, PMIC code
cleanups (Bin Gao, Felipe Balbi, Paul Gortmaker).
- New driver for the power participant device which is part of the
Dynamic Power and Thermal Framework (DPTF) and DPTF-related code
reorganization (Srinivas Pandruvada).
- Support for the platform-initiated graceful shutdown feature
introduced in ACPI 6.1 (Prashanth Prakash).
- ACPI button driver update related to lid input events generated
automatically on initialization and system resume that have been
problematic for some time (Lv Zheng).
- ACPI EC driver cleanups (Lv Zheng).
- Documentation of the ACPICA release automation process and the
in-kernel ACPI AML debugger (Lv Zheng).
- New blacklist entry and two fixes for the ACPI backlight driver
(Alex Hung, Arvind Yadav, Ralf Gerbig).
- Cleanups of the ACPI pci_slot driver (Joe Perches, Paul Gortmaker).
- ACPI CPPC code changes to make it more robust against possible
defects in ACPI tables and new symbol definitions for PCC (Hoan
Tran).
- System reboot code modification to execute the ACPI _PTS (Prepare
To Sleep) method in addition to _TTS (Ocean He).
- ACPICA-related change to carry out lock ordering checks in ACPICA
if ACPICA debug is enabled in the kernel (Lv Zheng).
- Assorted minor fixes and cleanups (Andy Shevchenko, Baoquan He,
Bhaktipriya Shridhar, Paul Gortmaker, Rafael Wysocki)"
* tag 'acpi-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (71 commits)
ACPI: enable ACPI_PROCESSOR_IDLE on ARM64
arm64: add support for ACPI Low Power Idle(LPI)
drivers: firmware: psci: initialise idle states using ACPI LPI
cpuidle: introduce CPU_PM_CPU_IDLE_ENTER macro for ARM{32, 64}
arm64: cpuidle: drop __init section marker to arm_cpuidle_init
ACPI / processor_idle: Add support for Low Power Idle(LPI) states
ACPI / processor_idle: introduce ACPI_PROCESSOR_CSTATE
ACPI / DPTF: move int340x_thermal.c to the DPTF folder
ACPI / DPTF: Add DPTF power participant driver
ACPI / lpat: make it explicitly non-modular
ACPI / dock: make dock explicitly non-modular
ACPI / PCI: make pci_slot explicitly non-modular
ACPI / PMIC: remove modular references from non-modular code
ACPICA: Linux: Enable ACPI_MUTEX_DEBUG for Linux kernel
ACPI: Rename configfs.c to acpi_configfs.c to prevent link error
ACPI / debugger: Add AML debugger documentation
ACPI: Add documentation describing ACPICA release automation
ACPI: add support for loading SSDTs via configfs
ACPI: add support for configfs
efi / ACPI: load SSTDs from EFI variables
...
Nicolai Stange