This reverts commit 13a229abc2.
Quoth Andi:
"After some consideration and feedback from various people it turns
out this wasn't that good an idea. It has some problems and needs
more work. Since it was only an optimization anyways it's best to
just back it out again for now."
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Big Unisys systems have multiple clusters too, but they have an
synchronized TSC.
I'm using the SMBIOS to check for vendor == IBM.
Cc: Chris McDermott <lcm@us.ibm.com>
Cc: "Protasevich, Natalie" <Natalie.Protasevich@unisys.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[description from AK]
The IBM Summit 3 chipset doesn't implement the HPET timer replacement
option. Since the current Linux code relies on it use a mixed mode with
both PIT for the interrupt and HPET counters for the time keeping. That
was already implemented, but didn't work properly because it was still
using the last interrupt offset in HPET. This resulted in x460 not
booting. Fix this up by using the free running HPET counter.
Shouldn't affect any other machine because they either use full HPET mode
or no HPET at all.
TBD needs a similar 32bit fix.
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Pallipadi, Venkatesh" <venkatesh.pallipadi@intel.com>
Cc: Bob Picco <bob.picco@hp.com>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It's bad juju to touch the APIC when it hasn't been enabled.
I also moved ack_bad_irq for x86-64 out of line following i386.
Signed-off-by: Andi Kleen <ak@suse.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On some broken motherboards (at least one NForce3 based AMD64 laptop)
the PIT timer runs at a incorrect frequency. This patch adds a new
option "apicpmtimer" that allows to use the APIC timer and calibrate it
using the PMTimer. It requires the earlier patch that allows to run the
main timer from the APIC.
Specifying apicpmtimer implies apicmaintimer.
The option defaults to off for now.
I tested it on a few systems and the resulting APIC timer frequencies
were usually a bit off, but always <1%, which should be tolerable.
TBD figure out heuristic to enable this automatically on the affected
systems TBD perhaps do it on all NForce3s or using DMI?
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Another piece from the no-idle-tick patch.
This can be enabled with the "apicmaintimer" option.
This is mainly useful when the PIT/HPET interrupt is unreliable.
Note there are some systems that are known to stop the APIC
timer in C3. For those it will never work, but this case
should be automatically detected.
It also only works with PM timer right now. When HPET is used
the way the main timer handler computes the delay doesn't work.
It should be a bit more efficient because there is one less
regular interrupt to process on the boot processor.
Requires earlier bugfix from Venkatesh
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove support for obsolete hardware and cleanup.
- Remove checks for non integrated APICs
- Replace apic_write_around with apic_write.
- Remove apic_read_around
- Remove APIC version reads used by old workarounds
- Remove old workaround for Simics
- Fix indentation
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
o Apic id is in most significant 8 bits of APIC_ID register. Current code
is trying to write apic id to least significant 8 bits. This patch fixes
it.
o This fix enables booting uni kdump capture kernel on a cpu with non-zero
apic id.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds a new notifier chain that is called with IDLE_START
when a CPU goes idle and IDLE_END when it goes out of idle.
The context can be idle thread or interrupt context.
Since we cannot rely on MONITOR/MWAIT existing the idle
end check currently has to be done in all interrupt
handlers.
They were originally inspired by the similar s390 implementation.
They have a variety of applications:
- They will be needed for CONFIG_NO_IDLE_HZ
- They can be used for oprofile to fix up the missing time
in idle when performance counters don't tick.
- They can be used for better C state management in ACPI
- They could be used for microstate accounting.
This is just infrastructure so far, no users.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Whenever we see that a CPU is capable of C3 (during ACPI cstate init), we
disable local APIC timer and switch to using a broadcast from external timer
interrupt (IRQ 0).
Patch below adds the code for x86_64.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the finer control of local APIC timer. We cannot provide a sub-jiffy
control like this when we use broadcast from external timer in place of
local APIC. Instead of removing this only on systems that may end up using
broadcast from external timer (due to C3), I am going the
"I'm feeling lucky" way to remove this fully. Basically, I am not sure about
usefulness of this code today. Few other architectures also don't seem to
support this today.
If you are using profiling and fine grained control and don't like this going
away in normal case, yell at me right now.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
MC4_MISC - DRAM Errors Threshold Register realized under AMD K8 Rev F.
This register is used to count correctable and uncorrectable ECC errors that occur during DRAM read operations.
The user may interface through sysfs files in order to change the threshold configuration.
bank%d/error_count - reads current error count, write to clear.
bank%d/interrupt_enable - set/clear interrupt enable.
bank%d/threshold_limit - read/write the threshold limit.
APIC vector 0xF9 in hw_irq.h.
5 software defined bank ids in mce.h.
new apic.c function to setup threshold apic lvt.
defaults to interrupt off, count enabled, and threshold limit max.
sysfs interface created on /sys/devices/system/threshold.
AK: added some ifdefs to make it compile on UP
Signed-off-by: Jacob Shin <jacob.shin@amd.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
... and with that all instances in arch/x86_64 are gone.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It could be wrong for kexec or other cases. Read it from
the CPU instead.
Signed-off-by: Murali <muralim@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Originally from Stuart Hayes.
When setting up the APIC for the Uniprocessor kernel don't
assume the CPU has an APIC ID of zero.
This fixes boot with the UP kernel on Dell PowerEdge 6800/6850 4way systems.
Cc: Stuart.Hayes@dell.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This was just needed for the Numasaurus, which fortunately
doesn't support x86-64 CPUs.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When coming out of apic mode attempt to set the appropriate
apic back into virtual wire mode. This improves on previous versions
of this patch by by never setting bot the local apic and the ioapic
into veritual wire mode.
This code looks at data from the mptable to see if an ioapic has
an ExtInt input to make this decision. A future improvement
is to figure out which apic or ioapic was in virtual wire mode
at boot time and to remember it. That is potentially a more accurate
method, of selecting which apic to place in virutal wire mode.
Signed-off-by: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds __cpuinit and __cpuinitdata sections that need to exist past
boot to support cpu hotplug.
Caveat: This is done *only* for EM64T CPU Hotplug support, on request from
Andi Kleen. Much of the generic hotplug code in kernel, and none of the other
archs that support CPU hotplug today, i386, ia64, ppc64, s390 and parisc dont
mark sections with __cpuinit, but only mark them as __devinit, and
__devinitdata.
If someone is motivated to change generic code, we need to make sure all
existing hotplug code does not break, on other arch's that dont use __cpuinit,
and __cpudevinit.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Acked-by: Andi Kleen <ak@muc.de>
Acked-by: Zwane Mwaikambo <zwane@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Collected NMI watchdog fixes.
- Fix call of check_nmi_watchdog
- Remove earlier move of check_nmi_watchdog to later. It does not fix the
race it was supposed to fix fully.
- Remove unused P6 definitions
- Add support for performance counter based watchdog on P4 systems.
This allows to run it only once per second, which saves some CPU time.
Previously it would run at 1000Hz, which was too much.
Code ported from i386
Make this the default on Intel systems.
- Use check_nmi_watchdog with local APIC based nmi
- Fix race in touch_nmi_watchdog
- Fix bug that caused incorrect performance counters to be programmed in a
few cases on K8.
- Remove useless check for local APIC
- Use local_t and per_cpu variables for per CPU data.
- Keep other CPUs busy during check_nmi_watchdog to make sure they really
tick when in lapic mode.
- Only check CPUs that are actually online.
- Various other fixes.
- Fix fallback path when MSRs are unimplemented
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use bitmap_zero instead of bitmap_empty to initialise cpu mask This makes it
actually run reliable instead of relying on stack state.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I thought I'm done with fixing u32 vs. pm_message_t ... unfortunately that
turned out not to be the case... Here are fixes x86-64.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Linus Torvalds