Allow an unpriviled user who has created a user namespace, and then
created a network namespace to effectively use the new network
namespace, by reducing capable(CAP_NET_ADMIN) and
capable(CAP_NET_RAW) calls to be ns_capable(net->user_ns,
CAP_NET_ADMIN), or capable(net->user_ns, CAP_NET_RAW) calls.
Settings that merely control a single network device are allowed.
Either the network device is a logical network device where
restrictions make no difference or the network device is hardware NIC
that has been explicity moved from the initial network namespace.
In general policy and network stack state changes are allowed while
resource control is left unchanged.
Allow the SIOCSIFADDR ioctl to add ipv6 addresses.
Allow the SIOCDIFADDR ioctl to delete ipv6 addresses.
Allow the SIOCADDRT ioctl to add ipv6 routes.
Allow the SIOCDELRT ioctl to delete ipv6 routes.
Allow creation of ipv6 raw sockets.
Allow setting the IPV6_JOIN_ANYCAST socket option.
Allow setting the IPV6_FL_A_RENEW parameter of the IPV6_FLOWLABEL_MGR
socket option.
Allow setting the IPV6_TRANSPARENT socket option.
Allow setting the IPV6_HOPOPTS socket option.
Allow setting the IPV6_RTHDRDSTOPTS socket option.
Allow setting the IPV6_DSTOPTS socket option.
Allow setting the IPV6_IPSEC_POLICY socket option.
Allow setting the IPV6_XFRM_POLICY socket option.
Allow sending packets with the IPV6_2292HOPOPTS control message.
Allow sending packets with the IPV6_2292DSTOPTS control message.
Allow sending packets with the IPV6_RTHDRDSTOPTS control message.
Allow setting the multicast routing socket options on non multicast
routing sockets.
Allow the SIOCADDTUNNEL, SIOCCHGTUNNEL, and SIOCDELTUNNEL ioctls for
setting up, changing and deleting tunnels over ipv6.
Allow the SIOCADDTUNNEL, SIOCCHGTUNNEL, SIOCDELTUNNEL ioctls for
setting up, changing and deleting ipv6 over ipv4 tunnels.
Allow the SIOCADDPRL, SIOCDELPRL, SIOCCHGPRL ioctls for adding,
deleting, and changing the potential router list for ISATAP tunnels.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- In rtnetlink_rcv_msg convert the capable(CAP_NET_ADMIN) check
to ns_capable(net->user-ns, CAP_NET_ADMIN). Allowing unprivileged
users to make netlink calls to modify their local network
namespace.
- In the rtnetlink doit methods add capable(CAP_NET_ADMIN) so
that calls that are not safe for unprivileged users are still
protected.
Later patches will remove the extra capable calls from methods
that are safe for unprivilged users.
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for supporting the creation of network namespaces
by unprivileged users, modify all of the per net sysctl exports
and refuse to allow them to unprivileged users.
This makes it safe for unprivileged users in general to access
per net sysctls, and allows sysctls to be exported to unprivileged
users on an individual basis as they are deemed safe.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces a new knob ndisc_notify. If enabled, the kernel
will transmit an unsolicited neighbour advertisement on link-layer address
change to update the neighbour tables of the corresponding hosts more quickly.
This is the equivalent to arp_notify in ipv4 world.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As suggested by Eric, we could introduce a helper function
for ipv6 too, to avoid checking if rt is NULL before
dst_release().
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In dev_forward_change(), it is useless to check if idev->dev
is NULL, it is always non-NULL here.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
#if defined(CONFIG_FOO) || defined(CONFIG_FOO_MODULE)
can be replaced by
#if IS_ENABLED(CONFIG_FOO)
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This message allows to get the devconf for an interface.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 1d5783030a (ipv6/addrconf: speedup /proc/net/if_inet6 filling)
added bugs hiding some devices from if_inet6 and breaking applications.
"ip -6 addr" could still display all IPv6 addresses, while "ifconfig -a"
couldnt.
One way to reproduce the bug is by starting in a shell :
unshare -n /bin/bash
ifconfig lo up
And in original net namespace, lo device disappeared from if_inet6
Reported-by: Jan Hinnerk Stosch <janhinnerk.stosch@gmail.com>
Tested-by: Jan Hinnerk Stosch <janhinnerk.stosch@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Mihai Maruseac <mihai.maruseac@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an address is added on loopback (ip -6 a a 2002::1/128 dev lo), a route
to fe80::/64 is added in the main table:
unreachable fe80::/64 dev lo proto kernel metric 256 error -101
This route does not match any prefix (no fe80:: address on lo). In fact,
addrconf_dev_config() will not add link local address because this function
filters interfaces by type. If the link local address is added manually, the
route to the link local prefix will be automatically added by
addrconf_add_linklocal().
Note also, that this route is not deleted when the address is removed.
After looking at the code, it seems that addrconf_add_lroute() is redundant with
addrconf_add_linklocal(), because this function will add the link local route
when the link local address is configured.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an address is added on loopback (ip -6 a a 2002::1/128 dev lo), two routes
are added:
- one in the local table:
local 2002::1 via :: dev lo proto none metric 0
- one the in main table (for the prefix):
unreachable 2002::1 dev lo proto kernel metric 256 error -101
When the address is deleted, the route inserted in the main table remains
because we use rt6_lookup(), which returns NULL when dst->error is set, which
is the case here! Thus, it is better to use ip6_route_lookup() to avoid this
kind of filter.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
geting route info does not write rt->rt6i_table, so replace
write lock with read lock
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Compare bits up to the source address's prefix length only to
allows DNS load balancing to continue to be used as a tie breaker.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is a frequent mistake to confuse the netlink port identifier with a
process identifier. Try to reduce this confusion by renaming fields
that hold port identifiers portid instead of pid.
I have carefully avoided changing the structures exported to
userspace to avoid changing the userspace API.
I have successfully built an allyesconfig kernel with this change.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__ipv6_regen_rndid no longer returns anything other than 0
so there's no point in verifying what it returns
Signed-off-by: Sorin Dumitru <sdumitru@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Biederman pointed out that not holding RTNL while calling
call_netdevice_notifiers() was racy.
This patch is a direct transcription his feedback
against commit 0115e8e30d (net: remove delay at device dismantle)
Thanks Eric !
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Mahesh Bandewar <maheshb@google.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Gao feng <gaofeng@cn.fujitsu.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I noticed extra one second delay in device dismantle, tracked down to
a call to dst_dev_event() while some call_rcu() are still in RCU queues.
These call_rcu() were posted by rt_free(struct rtable *rt) calls.
We then wait a little (but one second) in netdev_wait_allrefs() before
kicking again NETDEV_UNREGISTER.
As the call_rcu() are now completed, dst_dev_event() can do the needed
device swap on busy dst.
To solve this problem, add a new NETDEV_UNREGISTER_FINAL, called
after a rcu_barrier(), but outside of RTNL lock.
Use NETDEV_UNREGISTER_FINAL with care !
Change dst_dev_event() handler to react to NETDEV_UNREGISTER_FINAL
Also remove NETDEV_UNREGISTER_BATCH, as its not used anymore after
IP cache removal.
With help from Gao feng
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Mahesh Bandewar <maheshb@google.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce ipv6_addr_hash() helper doing a XOR on all bits
of an IPv6 address, with an optimized x86_64 version.
Use it in flow dissector, as suggested by Andrew McGregor,
to reduce hash collision probabilities in fq_codel (and other
users of flow dissector)
Use it in ip6_tunnel.c and use more bit shuffling, as suggested
by David Laight, as existing hash was ignoring most of them.
Use it in sunrpc and use more bit shuffling, using hash_32().
Use it in net/ipv6/addrconf.c, using hash_32() as well.
As a cleanup, use it in net/ipv4/tcp_metrics.c
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrew McGregor <andrewmcgr@gmail.com>
Cc: Dave Taht <dave.taht@gmail.com>
Cc: Tom Herbert <therbert@google.com>
Cc: David Laight <David.Laight@ACULAB.COM>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the current debugging style and enable dynamic_debug.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add #define pr_fmt(fmt) as appropriate.
Add "IPv6: " to appropriate files.
Convert printk(KERN_<LEVEL> to pr_<level> (but not KERN_DEBUG).
Standardize on "%s: " not "%s(): " when emitting __func__.
Use "%s: ", __func__ instead of embedding function name.
Coalesce formats, align arguments.
ADDRCONF output is now prefixed with "IPv6: "
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are going to delete the Token ring support. This removes any
special processing in the core networking for token ring, (aside
from net/tr.c itself), leaving the drivers and remaining tokenring
support present but inert.
The mass removal of the drivers and net/tr.c will be in a separate
commit, so that the history of these files that we still care
about won't have the giant deletion tied into their history.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Standardize the net core ratelimited logging functions.
Coalesce formats, align arguments.
Change a printk then vprintk sequence to use printf extension %pV.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the RFC4944 (Transmission of IPv6 Packets over
IEEE 802.15.4 Networks), chapter 7:
The IPv6 link-local address [RFC4291] for an IEEE 802.15.4 interface
is formed by appending the Interface Identifier, as defined above, to
the prefix FE80::/64.
10 bits 54 bits 64 bits
+----------+-----------------------+----------------------------+
|1111111010| (zeros) | Interface Identifier |
+----------+-----------------------+----------------------------+
This patch adds IPv6 address generation support for the 6lowpan
interfaces.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using an ascii path to register_net_sysctl as opposed to the slightly
awkward ctl_path allows for much simpler code.
We no longer need to malloc dev_name to keep it alive the length of our
sysctl register instead we can use a small temporary buffer on the
stack.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/atheros/atlx/atl1.c
drivers/net/ethernet/atheros/atlx/atl1.h
Resolved a conflict between a DMA error bug fix and NAPI
support changes in the atl1 driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
If the ipv6 dst cache which copy from the dst generated by ICMPV6 RA packet.
this dst cache will not check expire because it has no RTF_EXPIRES flag.
So this dst cache will always be used until the dst gc run.
Change the struct dst_entry,add a union contains new pointer from and expires.
When rt6_info.rt6i_flags has no RTF_EXPIRES flag,the dst.expires has no use.
we can use this field to point to where the dst cache copy from.
The dst.from is only used in IPV6.
rt6_check_expired check if rt6_info.dst.from is expired.
ip6_rt_copy only set dst.from when the ort has flag RTF_ADDRCONF
and RTF_DEFAULT.then hold the ort.
ip6_dst_destroy release the ort.
Add some functions to operate the RTF_EXPIRES flag and expires(from) together.
and change the code to use these new adding functions.
Changes from v5:
modify ip6_route_add and ndisc_router_discovery to use new adding functions.
Only set dst.from when the ort has flag RTF_ADDRCONF
and RTF_DEFAULT.then hold the ort.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/ipv6/addrconf.c:340: WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
net/ipv6/addrconf.c:342: ERROR: "foo * bar" should be "foo *bar"
net/ipv6/addrconf.c:444: ERROR: "foo * bar" should be "foo *bar"
net/ipv6/addrconf.c:1337: WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
net/ipv6/addrconf.c:1526: ERROR: "(foo*)" should be "(foo *)"
net/ipv6/addrconf.c:1671: ERROR: open brace '{' following function declarations go on the next line
net/ipv6/addrconf.c:1914: ERROR: "foo * bar" should be "foo *bar"
net/ipv6/addrconf.c:2368: ERROR: "foo * bar" should be "foo *bar"
net/ipv6/addrconf.c:2370: ERROR: "foo * bar" should be "foo *bar"
net/ipv6/addrconf.c:2416: ERROR: "foo * bar" should be "foo *bar"
net/ipv6/addrconf.c:2437: ERROR: "foo * bar" should be "foo *bar"
net/ipv6/addrconf.c:2573: ERROR: "foo * bar" should be "foo *bar"
net/ipv6/addrconf.c:3797: ERROR: "foo* bar" should be "foo *bar"
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These macros contain a hidden goto, and are thus extremely error
prone and make code hard to audit.
Signed-off-by: David S. Miller <davem@davemloft.net>
With commit d6ddef9e641d(IPv6: Fix not join all-router mcast group
when forwarding set.) I check 'dev' after it's dereference that
leads to a Smatch complaint:
net/ipv6/addrconf.c:438 ipv6_add_dev()
warn: variable dereferenced before check 'dev' (see line 432)
net/ipv6/addrconf.c
431 /* protected by rtnl_lock */
432 rcu_assign_pointer(dev->ip6_ptr, ndev);
^^^^^^^^^^^^
Old dereference.
433
434 /* Join all-node multicast group */
435 ipv6_dev_mc_inc(dev, &in6addr_linklocal_allnodes);
436
437 /* Join all-router multicast group if forwarding is set
*/
438 if (ndev->cnf.forwarding && dev && (dev->flags &
IFF_MULTICAST))
^^^
Remove the check to avoid the complaint as 'dev' can't be NULL.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Li Wei <lw@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When forwarding was set and a new net device is register,
we need add this device to the all-router mcast group.
Signed-off-by: Li Wei <lw@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a race condition in addrconf_sysctl_forward() and
addrconf_sysctl_disable().
These functions change idev->cnf.forwarding (resp. idev->cnf.disable_ipv6)
and then try to grab the rtnl lock before performing any actions.
If that fails they restore the original value and restart the syscall.
This creates race conditions if ipv6 code tries to access
these parameters, or if multiple instances try to do the same operation.
As an example of the former, if __ipv6_ifa_notify() finds a 0 in
idev->cnf.forwarding when invoked by addrconf_ifdown() it may not free
anycast addresses, ultimately resulting in the net_device not being freed.
This patch reads the user parameters into a temporary location and only
writes the actual parameters when the rtnl lock is acquired.
Tested in 2.6.38.8.
Signed-off-by: Francesco Ruggeri <fruggeri@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit a9b3cd7f32 (rcu: convert uses of rcu_assign_pointer(x, NULL) to
RCU_INIT_POINTER) did a lot of incorrect changes, since it did a
complete conversion of rcu_assign_pointer(x, y) to RCU_INIT_POINTER(x,
y).
We miss needed barriers, even on x86, when y is not NULL.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Stephen Hemminger <shemminger@vyatta.com>
CC: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This ensures a linear behaviour when filling /proc/net/if_inet6 thus making
ifconfig run really fast on IPv6 only addresses. In fact, with this patch and
the IPv4 one sent a while ago, ifconfig will run in linear time regardless of
address type.
IPv4 related patch: f04565ddf5
dev: use name hash for dev_seq_ops
...
Some statistics (running ifconfig > /dev/null on a different setup):
iface count / IPv6 no-patch time / IPv6 patched time / IPv4 time
----------------------------------------------------------------
6250 | 0.23 s | 0.13 s | 0.11 s
12500 | 0.62 s | 0.28 s | 0.22 s
25000 | 2.91 s | 0.57 s | 0.46 s
50000 | 11.37 s | 1.21 s | 0.94 s
128000 | 86.78 s | 3.05 s | 2.54 s
Signed-off-by: Mihai Maruseac <mmaruseac@ixiacom.com>
Cc: Daniel Baluta <dbaluta@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently Dave noticed that a test we did in ipv6_add_addr to see if we next hop
route for the interface we're adding an addres to was wrong (see commit
7ffbcecbee). for one, it never triggers, and two,
it was completely wrong to begin with. This test was meant to cover this
section of RFC 4429:
3.3 Modifications to RFC 2462 Stateless Address Autoconfiguration
* (modifies section 5.5) A host MAY choose to configure a new address
as an Optimistic Address. A host that does not know the SLLAO
of its router SHOULD NOT configure a new address as Optimistic.
A router SHOULD NOT configure an Optimistic Address.
This patch should bring us into proper compliance with the above clause. Since
we only add a SLAAC address after we've received a RA which may or may not
contain a source link layer address option, we can pass a pointer to that option
to addrconf_prefix_rcv (which may be null if the option is not present), and
only set the optimistic flag if the option was found in the RA.
Change notes:
(v2) modified the new parameter to addrconf_prefix_rcv to be a bool rather than
a pointer to make its use more clear as per request from davem.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It just obscures that the netdevice pointer and the expires value are
implemented in the dst_entry sub-object of the ipv6 route.
And it makes grepping for dst_entry member uses much harder too.
Signed-off-by: David S. Miller <davem@davemloft.net>
The route we have here is for the address being added to the interface,
ie. for input packet processing.
Therefore using that route to determine whether an output nexthop gateway
is known and resolved doesn't make any sense.
So, simply remove this test, it never triggered anyways.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-By: Neil Horman <nhorman@tuxdriver.com>
There is no obvious reason to add a default multicast route for loopback
devices, otherwise there would be a route entry whose dst.error set to
-ENETUNREACH that would blocking all multicast packets.
====================
[ more detailed explanation ]
The problem is that the resulting routing table depends on the sequence
of interface's initialization and in some situation, that would block all
muticast packets. Suppose there are two interfaces on my computer
(lo and eth0), if we initailize 'lo' before 'eth0', the resuting routing
table(for multicast) would be
# ip -6 route show | grep ff00::
unreachable ff00::/8 dev lo metric 256 error -101
ff00::/8 dev eth0 metric 256
When sending multicasting packets, routing subsystem will return the first
route entry which with a error set to -101(ENETUNREACH).
I know the kernel will set the default ipv6 address for 'lo' when it is up
and won't set the default multicast route for it, but there is no reason to
stop 'init' program from setting address for 'lo', and that is exactly what
systemd did.
I am sure there is something wrong with kernel or systemd, currently I preferred
kernel caused this problem.
====================
Signed-off-by: Li Wei <lw@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To reflect the fact that a refrence is not obtained to the
resulting neighbour entry.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Roland Dreier <roland@purestorage.com>
C assignment can handle struct in6_addr copying.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
These files are non modular, but need to export symbols using
the macros now living in export.h -- call out the include so
that things won't break when we remove the implicit presence
of module.h from everywhere.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The route lookup to find a previously auto-configured route for a prefixes used
to use rt6_lookup(), with the prefix from the RA used as an address. However,
that kind of lookup ignores routing tables, the prefix length and route flags,
so when there were other matching routes, even in different tables and/or with
a different prefix length, the wrong route would be manipulated.
Now, a new function "addrconf_get_prefix_route()" is used for the route lookup,
which searches in RT6_TABLE_PREFIX and takes the prefix-length and route flags
into account.
Signed-off-by: Andreas Hofmeister <andi@collax.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When calling snmp6_alloc_dev fails, the snmp6 relevant memory
are freed by snmp6_alloc_dev. Calling in6_dev_finish_destroy
will free these memory twice.
Double free will lead that undefined behavior occurs.
Signed-off-by: Roy Li <rongqing.li@windriver.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch improves the logic determining when to send ICMPv6 Router
Solicitations, so that they are 1) always sent when the kernel is
accepting Router Advertisements, and 2) never sent when the kernel is
not accepting RAs. In other words, the operational setting of the
"accept_ra" sysctl is used.
The change also makes the special "Hybrid Router" forwarding mode
("forwarding" sysctl set to 2) operate exactly the same as the standard
Router mode (forwarding=1). The only difference between the two was
that RSes was being sent in the Hybrid Router mode only. The sysctl
documentation describing the special Hybrid Router mode has therefore
been removed.
Rationale for the change:
Currently, the value of forwarding sysctl is the only thing determining
whether or not to send RSes. If it has the value 0 or 2, they are sent,
otherwise they are not. This leads to inconsistent behaviour in the
following cases:
* accept_ra=0, forwarding=0
* accept_ra=0, forwarding=2
* accept_ra=1, forwarding=2
* accept_ra=2, forwarding=1
In the first three cases, the kernel will send RSes, even though it will
not accept any RAs received in reply. In the last case, it will not send
any RSes, even though it will accept and process any RAs received. (Most
routers will send unsolicited RAs periodically, so suppressing RSes in
the last case will merely delay auto-configuration, not prevent it.)
Also, it is my opinion that having the forwarding sysctl control RS
sending behaviour (completely independent of whether RAs are being
accepted or not) is simply not what most users would intuitively expect
to be the case.
Signed-off-by: Tore Anderson <tore@fud.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gergely Kalman reported crashes in check_peer_redir().
It appears commit f39925dbde (ipv4: Cache learned redirect
information in inetpeer.) added a race, leading to possible NULL ptr
dereference.
Since we can now change dst neighbour, we should make sure a reader can
safely use a neighbour.
Add RCU protection to dst neighbour, and make sure check_peer_redir()
can be called safely by different cpus in parallel.
As neighbours are already freed after one RCU grace period, this patch
should not add typical RCU penalty (cache cold effects)
Many thanks to Gergely for providing a pretty report pointing to the
bug.
Reported-by: Gergely Kalman <synapse@hippy.csoma.elte.hu>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When assigning a NULL value to an RCU protected pointer, no barrier
is needed. The rcu_assign_pointer, used to handle that but will soon
change to not handle the special case.
Convert all rcu_assign_pointer of NULL value.
//smpl
@@ expression P; @@
- rcu_assign_pointer(P, NULL)
+ RCU_INIT_POINTER(P, NULL)
// </smpl>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the code to handle some of the differences between
RFC 3041 and RFC 4941, which obsoletes it. Also a couple
of janitorial fixes.
- Allow router advertisements to increase the lifetime of
temporary addresses. This was not allowed by RFC 3041,
but is specified by RFC 4941. It is useful when RA
lifetimes are lower than TEMP_{VALID,PREFERRED}_LIFETIME:
in this case, the previous code would delete or deprecate
addresses prematurely.
- Change the default of MAX_RETRY to 3 per RFC 4941.
- Add a comment to clarify that the preferred and valid
lifetimes in inet6_ifaddr are relative to the timestamp.
- Shorten lines to 80 characters in a couple of places.
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Original commit 2bda8a0c8af... "Disable router anycast
address for /127 prefixes" says:
| No need for matching code in addrconf_leave_anycast() as it
| will silently ignore any attempt to leave an unknown anycast
| address.
After analysis, because 1) we may add two or more prefixes on the
same interface, or 2)user may have manually joined that anycast,
we may hit chances to have anycast address which as if we had
generated one by /127 prefix and we should not leave from subnet-
router anycast address unconditionally.
CC: Bjørn Mork <bjorn@mork.no>
CC: Brian Haley <brian.haley@hp.com>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It just makes it harder to see 1) what the code is doing
and 2) grep for all users of dst{->,.}neighbour
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC 6164 requires that routers MUST disable Subnet-Router anycast
for the prefix when /127 prefixes are used.
No need for matching code in addrconf_leave_anycast() as it
will silently ignore any attempt to leave an unknown anycast
address.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The message size allocated for rtnl ifinfo dumps was limited to
a single page. This is not enough for additional interface info
available with devices that support SR-IOV and caused a bug in
which VF info would not be displayed if more than approximately
40 VFs were created per interface.
Implement a new function pointer for the rtnl_register service that will
calculate the amount of data required for the ifinfo dump and allocate
enough data to satisfy the request.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use same logic as SIT tunnel to handle link local address
for GRE tunnel. OSPFv3 requires link-local address to function.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1446 commits)
macvlan: fix panic if lowerdev in a bond
tg3: Add braces around 5906 workaround.
tg3: Fix NETIF_F_LOOPBACK error
macvlan: remove one synchronize_rcu() call
networking: NET_CLS_ROUTE4 depends on INET
irda: Fix error propagation in ircomm_lmp_connect_response()
irda: Kill set but unused variable 'bytes' in irlan_check_command_param()
irda: Kill set but unused variable 'clen' in ircomm_connect_indication()
rxrpc: Fix set but unused variable 'usage' in rxrpc_get_transport()
be2net: Kill set but unused variable 'req' in lancer_fw_download()
irda: Kill set but unused vars 'saddr' and 'daddr' in irlan_provider_connect_indication()
atl1c: atl1c_resume() is only used when CONFIG_PM_SLEEP is defined.
rxrpc: Fix set but unused variable 'usage' in rxrpc_get_peer().
rxrpc: Kill set but unused variable 'local' in rxrpc_UDP_error_handler()
rxrpc: Kill set but unused variable 'sp' in rxrpc_process_connection()
rxrpc: Kill set but unused variable 'sp' in rxrpc_rotate_tx_window()
pkt_sched: Kill set but unused variable 'protocol' in tc_classify()
isdn: capi: Use pr_debug() instead of ifdefs.
tg3: Update version to 3.119
tg3: Apply rx_discards fix to 5719/5720
...
Fix up trivial conflicts in arch/x86/Kconfig and net/mac80211/agg-tx.c
as per Davem.
ipv6 has per device ICMP SNMP counters, taking too much space because
they use percpu storage.
needed size per device is :
(512+4)*sizeof(long)*number_of_possible_cpus*2
On a 32bit kernel, 16 possible cpus, this wastes more than 64kbytes of
memory per ipv6 enabled network device, taken in vmalloc pool.
Since ICMP messages are rare, just use shared counters (atomic_long_t)
Per network space ICMP counters are still using percpu memory, we might
also convert them to shared counters in a future patch.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Denys Fedoryshchenko <denys@visp.net.lb>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rcu callback inet6_ifa_finish_destroy_rcu() just calls a kfree(),
so we use kfree_rcu() instead of the call_rcu(inet6_ifa_finish_destroy_rcu).
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
The rcu callback in6_dev_finish_destroy_rcu() just calls a kfree(),
so we use kfree_rcu() instead of the call_rcu(in6_dev_finish_destroy_rcu).
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
ctl_table_headers registered with register_net_sysctl_table should
have been unregistered with the equivalent unregister_net_sysctl_table
Signed-off-by: Lucian Adrian Grijincu <lucian.grijincu@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add const qualifiers to structs iphdr, ipv6hdr and in6_addr pointers
where possible, to make code intention more obvious.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[ipv6] Add support for RTA_PREFSRC
This patch allows a user to select the preferred source address
for a specific IPv6-Route. It can be set via a netlink message
setting RTA_PREFSRC to a valid IPv6 address which must be
up on the device the route will be bound to.
Signed-off-by: Daniel Walter <dwalter@barracuda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hash is declared and assigned but not used anymore. ipv6_addr_hash()
exhibit no side-effects.
Signed-off-by: Hagen Paul Pfeifer <hagen@jauu.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts the following set of commits:
d1ed113f16 ("ipv6: remove duplicate neigh_ifdown")
29ba5fed1b ("ipv6: don't flush routes when setting loopback down")
9d82ca98f7 ("ipv6: fix missing in6_ifa_put in addrconf")
2de7957072 ("ipv6: addrconf: don't remove address state on ifdown if the address is being kept")
8595805aaf ("IPv6: only notify protocols if address is compeletely gone")
27bdb2abcc ("IPv6: keep tentative addresses in hash table")
93fa159abe ("IPv6: keep route for tentative address")
8f37ada5b5 ("IPv6: fix race between cleanup and add/delete address")
84e8b803f1 ("IPv6: addrconf notify when address is unavailable")
dc2b99f71e ("IPv6: keep permanent addresses on admin down")
because the core semantic change to ipv6 address handling on ifdown
has broken some things, in particular "disable_ipv6" sysctl handling.
Stephen has made several attempts to get things back in working order,
but nothing has restored disable_ipv6 fully yet.
Reported-by: Eric W. Biederman <ebiederm@xmission.com>
Tested-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a network namespace is created (via CLONE_NEWNET), the loopback
interface is automatically added to the new namespace, triggering a
printk in ipv6_add_dev() if CONFIG_IPV6_PRIVACY is set.
This is problematic for applications which use CLONE_NEWNET as
part of a sandbox, like Chromium's suid sandbox or recent versions of
vsftpd. On a busy machine, it can lead to thousands of useless
"lo: Disabled Privacy Extensions" messages appearing in dmesg.
It's easy enough to check the status of privacy extensions via the
use_tempaddr sysctl, so just removing the printk seems like the most
sensible solution.
Signed-off-by: Romain Francoise <romain@orebokech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When device is being set to down, neigh_ifdown was being called
twice. Once from addrconf notifier and once from ndisc notifier.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When loopback device is being brought down, then keep the route table
entries because they are special. The entries in the local table for
linklocal routes and ::1 address should not be purged.
This is a sub optimal solution to the problem and should be replaced
by a better fix in future.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New idev are advertised with NL group RTNLGRP_IPV6_IFADDR, but
should use RTNLGRP_IPV6_IFINFO.
Bug was introduced by commit 8d7a76c9.
Signed-off-by: Wang Xuefu <xuefu.wang@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Thomas Graf <tgraf@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As David pointed out correctly, updates to af-specific attributes
are currently not atomic. If multiple changes are requested and
one of them fails, previous updates may have been applied already
leaving the link behind in a undefined state.
This patch splits the function parse_link_af() into two functions
validate_link_af() and set_link_at(). validate_link_af() is placed
to validate_linkmsg() check for errors as early as possible before
any changes to the link have been made. set_link_af() is called to
commit the changes later.
This method is not fail proof, while it is currently sufficient
to make set_link_af() inerrable and thus 100% atomic, the
validation function method will not be able to detect all error
scenarios in the future, there will likely always be errors
depending on states which are f.e. not protected by rtnl_mutex
and thus may change between validation and setting.
Also, instead of silently ignoring unknown address families and
config blocks for address families which did not register a set
function the errors EAFNOSUPPORT respectively EOPNOSUPPORT are
returned to avoid comitting 4 out of 5 update requests without
notifying the user.
Signed-off-by: Thomas Graf <tgraf@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix ref count bug introduced by
commit 2de7957072
Author: Lorenzo Colitti <lorenzo@google.com>
Date: Wed Oct 27 18:16:49 2010 +0000
ipv6: addrconf: don't remove address state on ifdown if the address
is being kept
Fix logic so that addrconf_ifdown() decrements the inet6_ifaddr
refcnt correctly with in6_ifa_put().
Reported-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expose reachable and retrans timer values in msecs instead of jiffies.
Both timer values are already exposed as msecs in the neighbour table
netlink interface.
The creation timestamp format with increased precision is kept but
cleaned up.
Signed-off-by: Thomas Graf <tgraf@infradead.org>
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
IFLA_PROTINFO exposes timer related per device settings in jiffies.
Change it to expose these values in msecs like the sysctl interface
does.
I did not find any users of IFLA_PROTINFO which rely on any of these
values and even if there are, they are likely already broken because
there is no way for them to reliably convert such a value to another
time format.
Signed-off-by: Thomas Graf <tgraf@infradead.org>
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 already exposes some address family data via netlink in the
IFLA_PROTINFO attribute if RTM_GETLINK request is sent with the
address family set to AF_INET6. We take over this format and
reuse all the code.
Signed-off-by: Thomas Graf <tgraf@infradead.org>
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix ref count bug introduced by
commit 2de7957072
Author: Lorenzo Colitti <lorenzo@google.com>
Date: Wed Oct 27 18:16:49 2010 +0000
ipv6: addrconf: don't remove address state on ifdown if the address
is being kept
Fix logic so that addrconf_ifdown() decrements the inet6_ifaddr
refcnt correctly with in6_ifa_put().
Reported-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, addrconf_ifdown does not delete statically configured IPv6
addresses when the interface is brought down. The intent is that when
the interface comes back up the address will be usable again. However,
this doesn't actually work, because the system stops listening on the
corresponding solicited-node multicast address, so the address cannot
respond to neighbor solicitations and thus receive traffic. Also, the
code notifies the rest of the system that the address is being deleted
(e.g, RTM_DELADDR), even though it is not. Fix it so that none of this
state is updated if the address is being kept on the interface.
Tested: Added a statically configured IPv6 address to an interface,
started ping, brought link down, brought link up again. When link came
up ping kept on going and "ip -6 maddr" showed that the host was still
subscribed to there
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After running this bonding setup script
modprobe bonding miimon=100 mode=0 max_bonds=1
ifconfig bond0 10.1.1.1/16
ifenslave bond0 eth1
ifenslave bond0 eth3
on s390 with qeth-driven slaves, modprobe -r fails with this message
unregister_netdevice: waiting for bond0 to become free. Usage count = 1
due to twice detection of duplicate address.
Problem is caused by a missing decrease of ifp->refcnt in addrconf_dad_failure.
An extra call of in6_ifa_put(ifp) solves it.
Problem has been introduced with commit f2344a131b.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a bug in the interaction between ipv6_create_tempaddr and
addrconf_verify. Because ipv6_create_tempaddr uses the cstamp and tstamp
from the public address in creating a private address, if we have not
received a router advertisement in a while, tstamp + temp_valid_lft might be
< now. If this happens, the new address is created inside
ipv6_create_tempaddr, then the loop within addrconf_verify starts again and
the address is immediately deleted. We are left with no temporary addresses
on the interface, and no more will be created until the public IP address is
updated. To avoid this, set the expiry time to be the minimum of the time
left on the public address or the config option PLUS the current age of the
public interface.
Signed-off-by: Glenn Wurster <gwurster@scs.carleton.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
If privacy extentions are enabled, but no current temporary address exists,
then create one when we get a router advertisement.
Signed-off-by: Glenn Wurster <gwurster@scs.carleton.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Another exported symbol only used in one file
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean up a missing exit path in the ipv6 module init routines. In
addrconf_init we call ipv6_addr_label_init which calls register_pernet_subsys
for the ipv6_addr_label_ops structure. But if module loading fails, or if the
ipv6 module is removed, there is no corresponding unregister_pernet_subsys call,
which leaves a now-bogus address on the pernet_list, leading to oopses in
subsequent registrations. This patch cleans up both the failed load path and
the unload path. Tested by myself with good results.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
include/net/addrconf.h | 1 +
net/ipv6/addrconf.c | 11 ++++++++---
net/ipv6/addrlabel.c | 5 +++++
3 files changed, 14 insertions(+), 3 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
Change "return (EXPR);" to "return EXPR;"
return is not a function, parentheses are not required.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to accepting router advertisement, the IPv6 stack does not send router
solicitations if forwarding is enabled.
This patch enables this behavior to be overruled by setting forwarding to the
special value 2.
Signed-off-by: Thomas Graf <tgraf@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the interface has IPv6 disabled, don't add a multicast or
link-local route since we won't be adding a link-local address.
Reported-by: Mahesh Kelkar <maheshkelkar@gmail.com>
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
/proc/net/snmp and /proc/net/netstat expose SNMP counters.
Width of these counters is either 32 or 64 bits, depending on the size
of "unsigned long" in kernel.
This means user program parsing these files must already be prepared to
deal with 64bit values, regardless of user program being 32 or 64 bit.
This patch introduces 64bit snmp values for IPSTAT mib, where some
counters can wrap pretty fast if they are 32bit wide.
# netstat -s|egrep "InOctets|OutOctets"
InOctets: 244068329096
OutOctets: 244069348848
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
max_desync_factor can be configured per-interface, but nothing is
using the value.
Reported-by: Piotr Lewandowski <piotr.lewandowski@gmail.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since addresses are only revalidated every 2 minutes, the reported
valid_lft can underflow shortly before the address is deleted.
Clamp it to a minimum of 0, as for prefered_lft.
Reported-by: Piotr Lewandowski <piotr.lewandowski@gmail.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for 64bit snmp counters for some mibs,
add an 'align' parameter to snmp_mib_init(), instead
of assuming mibs only contain 'unsigned long' fields.
Callers can use __alignof__(type) to provide correct
alignment.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Herbert Xu <herbert@gondor.apana.org.au>
CC: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
CC: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
CC: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
remove useless union keyword in rtable, rt6_info and dn_route.
Since there is only one member in a union, the union keyword isn't useful.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch ensures that all places that schedule the DAD timer
look at the address state in a safe manner before scheduling the
timer. This ensures that we don't end up with pending timers
after deleting an address.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes use of the new POSTDAD state. This prevents
a race between DAD completion and failure.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes use of the new state_lock to synchronise between
updates to the ifa state. This fixes the issue where a remotely
triggered address deletion (through DAD failure) coincides with a
local administrative address deletion, causing certain actions to
be performed twice incorrectly.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces the boolean dead flag on inet6_ifaddr with
a state enum. This allows us to roll back changes when deleting
an address according to whether DAD has completed or not.
This patch only adds the state field and does not change the logic.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The duplicate address check code got broken in the conversion
to hlist (2.6.35). The earlier patch did not fix the case where
two addresses match same hash value. Use two exit paths,
rather than depending on state of loop variables (from macro).
Based on earlier fix by Shan Wei.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Reviewed-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add hlist_for_each_entry_rcu_bh() and
hlist_for_each_entry_continue_rcu_bh() macros, and use them in
ipv6_get_ifaddr(), if6_get_first() and if6_get_next() to fix lockdeps
warnings.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Reviewed-by: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sparse can help us find endianness bugs, but we need to make some
cleanups to be able to more easily spot real bugs.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The notifier for address down should only be called if address is completely
gone, not just being marked as tentative on link transistion. The code
in net-next would case bonding/sctp/s390 to see address disappear on link
down, but they would never see it reappear on link up.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since an address in hash list has to already have a ref count,
no additional ref count is needed.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When link goes down, want address to be preserved but in a tentative
state, therefore it has to stay in hash list.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent changes preserve IPv6 address when link goes down (good).
But would cause address to point to dead dst entry (bad).
The simplest fix is to just not delete route if address is
being held for later use.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
When a dump is interrupted at the last device in a hash chain and
then continued, "idx" won't get incremented past s_idx, so s_ip_idx
is not reset when moving on to the next device. This means of all
following devices only the last n - s_ip_idx addresses are dumped.
Tested-by: Pawel Staszewski <pstaszewski@itcare.pl>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Use list_add_tail() to get the behavior we had before
the list_head conversion for ipv6 address lists.
Signed-off-by: David S. Miller <davem@davemloft.net>
hlist_for_each_entry(p...) will not necessarily initialize 'p'
to anything if the hlist is empty. GCC notices this and emits
a warning.
Just return true explicitly when we hit a match, and return
false is we fall out of the loop without one.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reduces timer events while keeping accuracy by rounding
our timer and/or batching several address validations in addrconf_verify().
addrconf_verify() is called at earliest timeout among interface addresses'
timeouts, but at maximum ADDR_CHECK_FREQUENCY (120 secs).
In most cases, all of timeouts of interface addresses are long enough
(e.g. several hours or days vs 2 minutes), this timer is usually called
every ADDR_CHECK_FREQUENCY, and it is okay to be lazy.
(Note this timer could be eliminated if all code paths which modifies
variables related to timeouts call us manually, but it is another story.)
However, in other least but important cases, we try keeping accuracy.
When the real interface address timeout is coming, and the timeout
is just before the rounded timeout, we accept some error.
When a timeout has been reached, we also try batching other several
events in very near future.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable regen_advance is only used in the privacy case.
Move it to simplify code and eliminate ifdef's
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some minor stuff, reformat comments and add whitespace for clarity
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert to list macro's for the list of addresses per interface
in IPv6.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing hash function has a couple of issues:
* it is hardwired to 16 for IN6_ADDR_HSIZE
* limited to 256 and callers using int
* use jhash2 rather than some old BSD algorithm
No need for random seed since this is local only (based on assigned
addresses) table.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert from reader/writer lock to RCU and spinlock for addrconf
hash list.
Adds an additional helper macro for hlist_for_each_entry_continue_rcu
to handle the continue case.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using hash list macros, simplifies code and helps later RCU.
This patch includes some initialization that is not strictly necessary,
since an empty hlist node/list is all zero; and list is in BSS
and node is allocated with kzalloc.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use list macros instead of open coded linked list.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since generally there could be more netdevices changing type other
than bonding, making this event type name "bonding-unrelated"
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we are managing IPv6 addresses using DHCP, it would be nice
for user-space to be notified if an address configured through
DHCP fails DAD. Otherwise user-space would have to poll to see
whether DAD succeeds.
This patch uses the existing notification mechanism and simply
hooks it into the DAD failure code path.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This solves a potential race problem during the cleanup process.
The issue is that addrconf_ifdown() needs to traverse address list,
but then drop lock to call the notifier. The version in -next
could get confused if add/delete happened during this window.
Original code (2.6.32 and earlier) was okay because all addresses
were always deleted.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
My recent change in net-next to retain permanent addresses caused regression.
Device refcount would not go to zero when device was unregistered because
left over anycast reference would hold ipv6 dev reference which would hold
device references...
The correct procedure is to call notify chain when address is no longer
available for use. When interface comes back DAD timer will notify
back that address is available.
Also, link local addresses should be purged when interface is brought
down. The address might be changed.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Router Solicitation timer races with device state changes
because it doesn't lock the device. Use local variable to avoid
one repeated dereference.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Timer code runs in bottom half, so there is no need for
using _bh form of locking. Also check if device is not ready
to avoid race with address that is no longer active.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC 4291 section 2.4 states that all uncategorized addresses
should be considered as Global Unicast.
This will remove IPV6_ADDR_RESERVED completely
and return IPV6_ADDR_UNICAST in ipv6_addr_type() instead.
Signed-off-by: Ulrich Weber <uweber@astaro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuck. It turns out that when we restart sysctls we were restarting
with the values already changed. Which unfortunately meant that
the second time through we thought there was no change and skipped
all kinds of work, despite the fact that there was indeed a change.
I have fixed this the simplest way possible by restoring the changed
values when we restart the sysctl write.
One of my coworkers spotted this bug when after disabling forwarding
on an interface pings were still forwarded.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add __percpu sparse annotations to net.
These annotations are to make sparse consider percpu variables to be
in a different address space and warn if accessed without going
through percpu accessors. This patch doesn't affect normal builds.
The macro and type tricks around snmp stats make things a bit
interesting. DEFINE/DECLARE_SNMP_STAT() macros mark the target field
as __percpu and SNMP_UPD_PO_STATS() macro is updated accordingly. All
snmp_mib_*() users which used to cast the argument to (void **) are
updated to cast it to (void __percpu **).
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Cc: Vlad Yasevich <vladislav.yasevich@hp.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Stop computing the number of neighbour table settings we have by
counting the number of binary sysctls. This behaviour was silly
and meant that we could not add another neighbour table setting
without also adding another binary sysctl.
Don't pass the binary sysctl path for neighour table entries
into neigh_sysctl_register. These parameters are no longer
used and so are just dead code.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't need to disable bottom half it is already down in the
previous lock. Move some blank lines to group locking in same
context.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Permanent IPV6 addresses should not be removed when the link is
set to admin down, only when device is removed.
When link is lost permanent addresses should be marked as tentative
so that when link comes back they are subject to duplicate address
detection (if DAD was enabled for that address).
Other routing systems keep manually configured IPv6 addresses
when link is set down.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__net_init/__net_exit are apparently not going away, so use them
to full extent.
In some cases __net_init was removed, because it was called from
__net_exit code.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1815 commits)
mac80211: fix reorder buffer release
iwmc3200wifi: Enable wimax core through module parameter
iwmc3200wifi: Add wifi-wimax coexistence mode as a module parameter
iwmc3200wifi: Coex table command does not expect a response
iwmc3200wifi: Update wiwi priority table
iwlwifi: driver version track kernel version
iwlwifi: indicate uCode type when fail dump error/event log
iwl3945: remove duplicated event logging code
b43: fix two warnings
ipw2100: fix rebooting hang with driver loaded
cfg80211: indent regulatory messages with spaces
iwmc3200wifi: fix NULL pointer dereference in pmkid update
mac80211: Fix TX status reporting for injected data frames
ath9k: enable 2GHz band only if the device supports it
airo: Fix integer overflow warning
rt2x00: Fix padding bug on L2PAD devices.
WE: Fix set events not propagated
b43legacy: avoid PPC fault during resume
b43: avoid PPC fault during resume
tcp: fix a timewait refcnt race
...
Fix up conflicts due to sysctl cleanups (dead sysctl_check code and
CTL_UNNUMBERED removed) in
kernel/sysctl_check.c
net/ipv4/sysctl_net_ipv4.c
net/ipv6/addrconf.c
net/sctp/sysctl.c
Generated with the following semantic patch
@@
struct net *n1;
struct net *n2;
@@
- n1 == n2
+ net_eq(n1, n2)
@@
struct net *n1;
struct net *n2;
@@
- n1 != n2
+ !net_eq(n1, n2)
applied over {include,net,drivers/net}.
Signed-off-by: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When handling large number of netdevices, inet6_dump_addr()
is very slow because it has O(N^2) complexity.
Instead of scanning one single list, we can use the NETDEV_HASHENTRIES
sub lists of the dev_index hash table, and RCU lookups.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that sys_sysctl is a compatiblity wrapper around /proc/sys
all sysctl strategy routines, and all ctl_name and strategy
entries in the sysctl tables are unused, and can be
revmoed.
In addition neigh_sysctl_register has been modified to no longer
take a strategy argument and it's callers have been modified not
to pass one.
Cc: "David Miller" <davem@davemloft.net>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: netdev@vger.kernel.org
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Reported by Stephen Rothwell:
--------------------
Today's linux-next build (x86_64 allmodconfig) produced this warning:
net/ipv6/addrconf.c: In function 'inet6_dump_ifinfo':
net/ipv6/addrconf.c:3833: warning: unused variable 'err'
Introduced by commit 84d2697d96 ("ipv6:
speedup inet6_dump_ifinfo()").
--------------------
Signed-off-by: David S. Miller <davem@davemloft.net>
Apparently, inet6_dump_addr() is not able to handle more than
64 ipv6 addresses per device. We must break from inner loops
in case skb is full, or else cursor is put at the end of list.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When handling large number of netdevice, inet6_dump_ifinfo()
is very slow because it has O(N^2) complexity.
Instead of scanning one single list, we can use the 256 sub lists
of the dev_index hash table, and RCU lookups.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds RCU management to the list of netdevices.
Convert some for_each_netdev() users to RCU version, if
it can avoid read_lock-ing dev_base_lock
Ie:
read_lock(&dev_base_loack);
for_each_netdev(net, dev)
some_action();
read_unlock(&dev_base_lock);
becomes :
rcu_read_lock();
for_each_netdev_rcu(net, dev)
some_action();
rcu_read_unlock();
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On Friday 02 October 2009 20:53:51 you wrote:
> This is good although I would have shortened the name.
Ah, I knew I forgot something :) Here is v4.
tavi
>From 24d96d825b9fa832b22878cc6c990d5711968734 Mon Sep 17 00:00:00 2001
From: Octavian Purdila <opurdila@ixiacom.com>
Date: Fri, 2 Oct 2009 00:51:15 +0300
Subject: [PATCH] ipv6: new sysctl for sending TLLAO with unicast NAs
Neighbor advertisements responding to unicast neighbor solicitations
did not include the target link-layer address option. This patch adds
a new sysctl option (disabled by default) which controls whether this
option should be sent even with unicast NAs.
The need for this arose because certain routers expect the TLLAO in
some situations even as a response to unicast NS packets.
Moreover, RFC 2461 recommends sending this to avoid a race condition
(section 4.4, Target link-layer address)
Signed-off-by: Cosmin Ratiu <cratiu@ixiacom.com>
Signed-off-by: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's unused.
It isn't needed -- read or write flag is already passed and sysctl
shouldn't care about the rest.
It _was_ used in two places at arch/frv for some reason.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: David Howells <dhowells@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If an interface has multiple addresses, the current message for DAD
failure isn't really helpful, so this patch adds the address itself to
the printk.
Signed-off-by: Jens Rosenboom <me@jayr.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes commit e36b9d16c6. The approach
there is to call dev_close()/dev_open() whenever the device type is changed in
order to remap the device IP multicast addresses to HW multicast addresses.
This approach suffers from 2 drawbacks:
*. It assumes tha the device is UP when calling dev_close(), or otherwise
dev_close() has no affect. It is worth to mention that initscripts (Redhat)
and sysconfig (Suse) doesn't act the same in this matter.
*. dev_close() has other side affects, like deleting entries from the routing
table, which might be unnecessary.
The fix here is to directly remap the IP multicast addresses to HW multicast
addresses for a bonding device that changes its type, and nothing else.
Reported-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Moni Shoua <monis@voltaire.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IFA_F_DADFAILED flag to denote an IPv6 address that has
failed Duplicate Address Detection, that way tools like
/sbin/ip can be more informative.
3: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qlen 1000
inet6 2001:db8::1/64 scope global tentative dadfailed
valid_lft forever preferred_lft forever
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a bug in addrconf_prefix_rcv() where it won't update the
preferred lifetime of an IPv6 address if the current valid lifetime
of the address is less than 2 hours (the minimum value in the RA).
For example, If I send a router advertisement with a prefix that
has valid lifetime = preferred lifetime = 2 hours we'll build
this address:
3: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qlen 1000
inet6 2001:1890:1109:a20:217:8ff:fe7d:4718/64 scope global dynamic
valid_lft 7175sec preferred_lft 7175sec
If I then send the same prefix with valid lifetime = preferred
lifetime = 0 it will be ignored since the minimum valid lifetime
is 2 hours:
3: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qlen 1000
inet6 2001:1890:1109:a20:217:8ff:fe7d:4718/64 scope global dynamic
valid_lft 7161sec preferred_lft 7161sec
But according to RFC 4862 we should always reset the preferred lifetime
even if the valid lifetime is invalid, which would cause the address
to immediately get deprecated. So with this patch we'd see this:
5: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qlen 1000
inet6 2001:1890:1109:a20:21f:29ff:fe5a:ef04/64 scope global deprecated dynamic
valid_lft 7163sec preferred_lft 0sec
The comment winds-up being 5x the size of the code to fix the problem.
Update the preferred lifetime of IPv6 addresses derived from a prefix
info option in a router advertisement even if the valid lifetime in
the option is invalid, as specified in RFC 4862 Section 5.5.3e. Fixes
an issue where an address will not immediately become deprecated.
Reported by Jens Rosenboom.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid showing wrong high values when the preferred lifetime of an address
is expired.
Signed-off-by: Jens Rosenboom <me@jayr.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 'autoconf' and 'disable_ipv6' parameters to the IPv6 module.
The first controls if IPv6 addresses are autoconfigured from
prefixes received in Router Advertisements. The IPv6 loopback
(::1) and link-local addresses are still configured.
The second controls if IPv6 addresses are desired at all. No
IPv6 addresses will be added to any interfaces.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A tunnel with no local ipv4 endpoint would otherwise use the
ISATAP linklocal address fe80::5efe:0:0, which is invalid. Rather not
add a linklocal address at all.
Signed-off-by: Sascha Hlusiak <contact@saschahlusiak.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just returning -ERESTARTSYS without a signal pending is not
good that will just leak it to userspace. We need return
-ERESTARTNOINTR so we always restart and set signal pending
so that we fall of the fast path of syscall return and setup
the system call restart.
So use restart_syscall() which does all of this for us.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ipv6 version of bind_conflict code calls ipv6_rcv_saddr_equal()
which at times wrongly identified intersections between addresses.
It particularly broke down under a few instances and caused erroneous
bind conflicts.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_sack_swap seems unnecessary so I pushed swap to the caller.
Also removed comment that seemed then pointless, and added include
when not already there. Compile tested.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the behavior of allowing both sysctl and addrconf_dad_failure()
to set the disable_ipv6 parameter without any bad side-effects.
If DAD fails and accept_dad > 1, we will still set disable_ipv6=1,
but then instead of allowing an RA to add an address then
immediately fail DAD, we simply don't allow the address to be
added in the first place. This also lets the user set this flag
and disable all IPv6 addresses on the interface, or on the entire
system.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a network namespace is destroyed the network interfaces are
all unregistered, making addrconf_ifdown called by the netdevice
notifier.
In the other hand, the addrconf exit method does a loop on the network
devices and does addrconf_ifdown on each of them. But the ordering of
the netns subsystem is not right because it uses the register_pernet_device
instead of register_pernet_subsys. If we handle the loopback as
any network device, we can safely use register_pernet_subsys.
But if we use register_pernet_subsys, the addrconf exit method will do
exactly what was already done with the unregistering of the network
devices. So in definitive, this code is pointless.
I removed the netns addrconf exit method and moved the code to the
addrconf cleanup function.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the return value of nlmsg_notify() as follows:
If NETLINK_BROADCAST_ERROR is set by any of the listeners and
an error in the delivery happened, return the broadcast error;
else if there are no listeners apart from the socket that
requested a change with the echo flag, return the result of the
unicast notification. Thus, with this patch, the unicast
notification is handled in the same way of a broadcast listener
that has set the NETLINK_BROADCAST_ERROR socket flag.
This patch is useful in case that the caller of nlmsg_notify()
wants to know the result of the delivery of a netlink notification
(including the broadcast delivery) and take any action in case
that the delivery failed. For example, ctnetlink can drop packets
if the event delivery failed to provide reliable logging and
state-synchronization at the cost of dropping packets.
This patch also modifies the rtnetlink code to ignore the return
value of rtnl_notify() in all callers. The function rtnl_notify()
(before this patch) returned the error of the unicast notification
which makes rtnl_set_sk_err() reports errors to all listeners. This
is not of any help since the origin of the change (the socket that
requested the echoing) notices the ENOBUFS error if the notification
fails and should resync itself.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel manages this value internally, as necessary, as
VIFs are added/removed and as multicast routers are registered
and deregistered.
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert to net_device_ops function table pointer for ioctl.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With some net devices types, an IPv6 address configured while the
interface was down can stay 'tentative' forever, even after the interface
is set up. In some case, pending IPv6 DADs are not executed when the
device becomes ready.
I observed this while doing some tests with kvm. If I assign an IPv6
address to my interface eth0 (kvm driver rtl8139) when it is still down
then the address is flagged tentative (IFA_F_TENTATIVE). Then, I set
eth0 up, and to my surprise, the address stays 'tentative', no DAD is
executed and the address can't be pinged.
I also observed the same behaviour, without kvm, with virtual interfaces
types macvlan and veth.
Some easy steps to reproduce the issue with macvlan:
1. ip link add link eth0 type macvlan
2. ip -6 addr add 2003::ab32/64 dev macvlan0
3. ip addr show dev macvlan0
...
inet6 2003::ab32/64 scope global tentative
...
4. ip link set macvlan0 up
5. ip addr show dev macvlan0
...
inet6 2003::ab32/64 scope global tentative
...
Address is still tentative
I think there's a bug in net/ipv6/addrconf.c, addrconf_notify():
addrconf_dad_run() is not always run when the interface is flagged IF_READY.
Currently it is only run when receiving NETDEV_CHANGE event. Looks like
some (virtual) devices doesn't send this event when becoming up.
For both NETDEV_UP and NETDEV_CHANGE events, when the interface becomes
ready, run_pending should be set to 1. Patch below.
'run_pending = 1' could be moved below the if/else block but it makes
the code less readable.
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
I want to compile out proc_* and sysctl_* handlers totally and
stub them to NULL depending on config options, however usage of &
will prevent this, since taking adress of NULL pointer will break
compilation.
So, drop & in front of every ->proc_handler and every ->strategy
handler, it was never needed in fact.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc warns when using the # modifier with the %p format specifier,
so we can't use this to omit the colons when needed, introduces
%pi6 instead.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The define in kernel.h can be done away with at a later time.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
name and nlen parameters passed to ->strategy hook are unused, remove
them. In general ->strategy hook should know what it's doing, and don't
do something tricky for which, say, pointer to original userspace array
may be needed (name).
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net> [ networking bits ]
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Matt Mackall <mpm@selenic.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes a problem spotted with zebra, but not sure if it is
necessary a kernel problem. With IPV6 when an address is added to an
interface, Zebra creates a duplicate RIB entry, one as a connected
route, and other as a kernel route.
When an address is added to an interface the RTN_NEWADDR message
causes Zebra to create a connected route. In IPV4 when an address is
added to an interface a RTN_NEWROUTE message is set to user space with
the protocol RTPROT_KERNEL. Zebra ignores these messages, because it
already has the connected route.
The problem is that route created in IPV6 has route protocol ==
RTPROT_BOOT. Was this a design decision or a bug? This fixes it. Same
patch applies to both net-2.6 and stable.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipv6_dev_get_saddr() blindly de-references dst_dev to get the network
namespace, but some callers might pass NULL. Change callers to pass a
namespace pointer instead.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removes legacy reinvent-the-wheel type thing. The generic
machinery integrates much better to automated debugging aids
such as kerneloops.org (and others), and is unambiguous due to
better naming. Non-intuively BUG_TRAP() is actually equal to
WARN_ON() rather than BUG_ON() though some might actually be
promoted to BUG_ON() but I left that to future.
I could make at least one BUILD_BUG_ON conversion.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consider the following scenario:
ipv6_del_addr(ifp)
ipv6_ifa_notify(RTM_DELADDR, ifp)
ip6_del_rt(ifp->rt)
after returning from the ipv6_ifa_notify and enabling BH-s
back, but *before* calling the addrconf_del_timer the
ifp->timer fires and:
addrconf_dad_timer(ifp)
addrconf_dad_completed(ifp)
ipv6_ifa_notify(RTM_NEWADDR, ifp)
ip6_ins_rt(ifp->rt)
then return back to the ipv6_del_addr and:
in6_ifa_put(ifp)
inet6_ifa_finish_destroy(ifp)
dst_release(&ifp->rt->u.dst)
After this we have an ifp->rt inserted into fib6 lists, but
queued for gc, which in turn can result in oopses in the
fib6_run_gc. Maybe some other nasty things, but we caught
only the oops in gc so far.
The solution is to disarm the ifp->timer before flushing the
rt from it.
Signed-off-by: Andrey Vagin <avagin@parallels.com>
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
- If 0, disable DAD.
- If 1, perform DAD (default).
- If >1, perform DAD and disable IPv6 operation if DAD for MAC-based
link-local address has been failed (RFC4862 5.4.5).
We do not follow RFC4862 by default. Refer to the netdev thread entitled
"Linux IPv6 DAD not full conform to RFC 4862 ?"
http://www.spinics.net/lists/netdev/msg52027.html
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Check the type of the address when adding a new one on interface.
- the unspecified address (::) is always disallowed (RFC4291 2.5.2)
- the loopback address is disallowed unless the interface is (one of)
loopback (RFC4291 2.5.3).
- multicast addresses are disallowed.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Large Receive Offload (LRO) is only appropriate for packets that are
destined for the host, and should be disabled if received packets may be
forwarded. It can also confuse the GSO on output.
Add dev_disable_lro() function which uses the appropriate ethtool ops to
disable LRO if enabled.
Add calls to dev_disable_lro() in br_add_if() and functions that enable
IPv4 and IPv6 forwarding.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes CVS keywords that weren't updated for a long time
from comments.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This pacth makes IPv6 address labels per network namespace.
It keeps the global label tables, ip6addrlbl_table, but
adds a 'net' member to each ip6addrlbl_entry.
This new member is taken into account when matching labels.
Changelog
=========
* v1: Initial version
* v2:
* Minize the penalty when network namespaces are not configured:
* the 'net' member is added only if CONFIG_NET_NS is
defined. This saves space when network namespaces are not
configured.
* 'net' value is retrieved with the inlined function
ip6addrlbl_net() that always return &init_net when
CONFIG_NET_NS is not defined.
* 'net' member in ip6addrlbl_entry renamed to the less generic
'lbl_net' name (helps code search).
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
This inline function, for readability, returns if the route
is a "prefix" route regardless if it was installed by RA or by
hand.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
- Allow longer lifetimes (>= 0x7fffffff/HZ) on 64bit archs
by using unsigned long.
- Shadow this arithmetic overflow workaround by introducing
helper functions: addrconf_timeout_fixup() and
addrconf_finite_timeout().
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Eric W. Biederman