On several places, whitespaces are being used for indentation,
or even at the end of the line.
Fix them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This API is still experimental. Make it optional, allowing to
compile the code without it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There is no dependency between the two, so remove the dependency in
Kconfig files.
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add support for CEC hardware that relies on low-level pin polling or
GPIO interrupts.
One example is the Allwinner SoC. But any GPIO-based CEC implementation can
use this as well.
A GPIO implementation is very suitable as well for debugging: it can use
interrupts to detect state changes and report it. Userspace can then verify
if the bus traffic is correct. This also makes error injection possible.
The disadvantage is that it is hard to get the timings right since linux
isn't a hard realtime system.
In general on an idle system it works quite well, but under load the timer
will miss its mark every so often.
The debugfs file /sys/kernel/debug/cec/cecX/status gives some statistics
with respect to the timer overruns.
When the adapter is unconfigured and the low-level driver supports
interrupts, then the interrupt will be used to detect changes. This should
be quite accurate. But when the adapter is configured a hrtimer has to be
used.
The hrtimer implements a state machine where for each state the code will
read the bus or drive the bus and go on to the next state. It will re-arm
the timer with a delay based on the next state.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This config option is strictly speaking independent of the
media subsystem since it can be used by drm as well.
Besides, it looks odd when drivers select CEC_CORE and
MEDIA_CEC_NOTIFIER, that's inconsistent naming.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The CEC framework is used by both drm and media. That makes it tricky
to get the dependencies right.
This patch moves the CEC_CORE and MEDIA_CEC_NOTIFIER config options
out of the media menu and instead drivers that want to use CEC should
select CEC_CORE and MEDIA_CEC_NOTIFIER (if needed).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The Kconfig options for the CEC subsystem were a bit messy. In
addition there were two cec sources (cec-edid.c and cec-notifier.c)
that were outside of the media/cec directory, which was weird.
Move those sources to media/cec as well.
The cec-edid and cec-notifier functionality is now part of the cec
module and these are no longer separate modules.
Also remove the MEDIA_CEC_EDID config option and include it with the
main CEC config option (which defined CEC_EDID anyway).
Added static inlines to cec-edid.h for dummy functions when CEC_CORE
isn't defined.
CEC drivers should now depend on CEC_CORE.
CEC drivers that need the cec-notifier functionality must explicitly
select CEC_NOTIFIER.
The s5p-cec and stih-cec drivers depended on VIDEO_DEV instead of
CEC_CORE, fix that as well.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add support for CEC notifiers, which is used to convey CEC physical address
information from video drivers to their CEC counterpart driver(s).
Based on an earlier version from Russell King:
https://patchwork.kernel.org/patch/9277043/
The cec_notifier is a reference counted object containing the CEC physical address
state of a video device.
When a new notifier is registered the current state will be reported to
that notifier at registration time.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
On some weird randconfigs, it is possible to select DVB
drivers, without having the DVB_CORE:
CONFIG_DVB_AU8522=m
CONFIG_DVB_AU8522_V4L=m
CONFIG_DVB_TUNER_DIB0090=m
This was never supposed to work, but changeset 22a613e898
("[media] dvb_frontend: merge duplicate dvb_tuner_ops.release implementations")
caused it to be exposed:
drivers/built-in.o: In function `fc0011_attach':
(.text+0x1598fb): undefined reference to `dvb_tuner_simple_release'
drivers/built-in.o:(.rodata+0x55e58): undefined reference to `dvb_tuner_simple_release'
drivers/built-in.o:(.rodata+0x57398): undefined reference to `dvb_tuner_simple_release'
Fixes: 22a613e898 ("[media] dvb_frontend: merge duplicate dvb_tuner_ops.release implementations")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The last open issues have been addressed, so it is time to move
this out of staging and into the mainline and to move the public
cec headers to include/uapi/linux.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The SPI driver looked a bit lonely in the config menu, and it didn't
support the autoselect. Shift things around a bit so it looks more logical.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
You can read datasheet here:
http://www.c-dis.net/media/871/GS1662_Datasheet.pdf
It's a component which supports HD and SD CEA or SDI formats
to SDI output. It's configured through SPI bus.
GS1662 driver is implemented as v4l2 subdev.
Signed-off-by: Charles-Antoine Couret <charles-antoine.couret@nexvision.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
- Use IS_REACHABLE(RC_CORE) instead of IS_ENABLED: if cec is built-in and
RC_CORE is a module, then CEC can't reach the RC symbols.
- Both cec and cec-edid should be bool and use the same build 'mode' as
MEDIA_SUPPORT (just as is done for the media controller code).
- Add a note to staging that this should be changed once the cec framework
is moved out of staging.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The cec-edid module contains helper functions to find and manipulate
the CEC physical address inside an EDID. Even if the CEC support itself
is disabled, drivers will still need these functions. Which is the
reason this is module is separate from the upcoming CEC framework.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This was depending on broken because we're working at the
Media Controller API, with has... issues.
As this got fixed, we can re-enable it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
While https was always supported on linuxtv.org, only in
Dec 3 2015 the website is using valid certificates.
As we're planning to drop pure http support on some
future, change all references at the media subsystem
to point to the https URL instead.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=iJ/U
-----END PGP SIGNATURE-----
Merge tag 'media/v4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Lots of improvements at the DVB API DocBook documentation. Now, the
frontend and the network APIs are fully in sync with the Kernel and
looks more like the rest of the media documentation;
- New frontend driver: cx24120
- New driver for a PCI device: cobalt. This driver is actually not
sold in the market, but it is a good example of a multi-HDMI input
device;
- The dt3155 driver were promoted from staging;
- The mantis driver got remote controller support;
- New V4L2 driver for ST bdisp SoC chipsets;
- Make sparse and smatch happier: several bugs were solved by fixing
the issues reported by those static code analyzers.
- Lots of new device additions, new features, improvements and cleanups
at the existing drivers.
* tag 'media/v4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (553 commits)
[media] lmedm04: fix the range for relative measurements
[media] lmedm04: use u32 instead of u64 for relative stats
[media] omap3isp: remove unused var
[media] saa7134: fix page size on some archs
[media] use CONFIG_PM_SLEEP for suspend/resume
[media] tuner-i2c: be consistent with I2C declaration
[media] si470x: cleanup define namespace
[media] bdisp: prevent compiling on random arch
[media] vb2: Don't WARN when v4l2_buffer.bytesused is 0 for multiplanar buffers
[media] MAINTAINERS: Add entry for the Renesas VSP1 driver
[media] videodev2.h: fix copy-and-paste error in V4L2_MAP_XFER_FUNC_DEFAULT
[media] Revert "[media] vb2: Push mmap_sem down to memops"
[media] mantis: cleanup a warning
[media] bdisp-debug: don't try to divide by s64
[media] cx88: don't declare restart_video_queue if not used
[media] au0828: move dev->boards atribuition to happen earlier
[media] lmedm04: implement dvb v5 statistics
[media] bdisp: remove unused var
[media] bdisp: remove needless check
ts2020: fix compilation on i386
...
Since when we start discussions about the usage Media Controller for
complex hardware, one thing become clear: the way it is, MC fails to
map anything different than capture/output/m2m video-only streaming.
The point is that MC has entities named as devnodes, but the only
devnode used (before the DVB patches) is MEDIA_ENT_T_DEVNODE_V4L.
Due to the way MC got implemented, however, this entity actually
doesn't represent the devnode, but the hardware I/O engine that
receives data via DMA.
By coincidence, such DMA is associated with the V4L device node
on webcam hardware, but this is not true even for other V4L2
devices. For example, on USB hardware, the DMA is done via the
USB controller. The data passes though a in-kernel filter that
strips off the URB headers. Other V4L2 devices like radio may not
even have DMA. When it have, the DMA is done via ALSA, and not
via the V4L devnode.
In other words, MC is broken as a whole, but tagging it as BROKEN
right now would do more harm than good.
So, instead, let's mark, for now, the DVB part as broken and
block all new changes to MC while we fix this mess, whith
we hopefully will do for the next Kernel version.
Requested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Media Controller DVB support is still an experimental feature,
as it is under heavy development. It is already said that it is
an experimental feature at the help, but let make it even clearer
and louder, as we may need to adjust some bits when we start using it
on embedded drivers.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Provide a way to register media controller device nodes
at the DVB core.
Please notice that the dvbdev callers also require changes
for the devices to be registered via the media controller.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
These drivers haven't been tested in a long, long time. The hardware is
ancient and hopelessly obsolete. These drivers also need to be converted
to newer media frameworks but due to the lack of hardware that's going
to be impossible. In addition, cheaper and vastly better hardware is
available today.
So these drivers are a prime candidate for removal. If someone is
interested in working on these drivers to prevent their removal, then
please contact the linux-media mailinglist.
Let's be honest, the age of parallel port webcams and ISA video capture
boards is really gone.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We should not select SPI bus when sub-driver auto-select is
selected. That option is meant for auto-selecting all possible
ancillary drivers used for selected board driver. Ancillary
drivers should define needed dependencies itself.
I2C and I2C_MUX are still selected here for a reason described on
commit 347f7a3763
Reverts commit e4462ffc16
Reported-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Mirics MSi001 and MSi2500 drivers uses SPI bus. Due to that we need
auto-select it too.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add software defined radio device support for media Kconfig.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As reported by the kbuild test robot <fengguang.wu@intel.com>:
> warning: (VIDEO_EM28XX_DVB) selects DVB_M88DS3103 which has unmet direct dependencies (MEDIA_SUPPORT && DVB_CORE && I2C && I2C_MUX)
> drivers/built-in.o: In function `m88ds3103_release':
> >> m88ds3103.c:(.text+0x1ab1af): undefined reference to `i2c_del_mux_adapter'
> drivers/built-in.o: In function `m88ds3103_attach':
> >> (.text+0x1ab342): undefined reference to `i2c_add_mux_adapter'
There are 3 possible ways to fix it:
1) make em28xx dependent on I2C_MUX.
That sounds wrong, as the em28xx bridge doesn't have i2c muxes on it,
and just one frontend has.
Well, subdevs could eventually be converted to, instead of using dvb
i2c gate control, to use i2c mux support.
That makes sense, but it takes time and lots of effort. Not sure if
this will happen anytime soon.
2) MEDIA_SUBDRV_AUTOSELECT can be dependent of I2C and I2C_MUX.
That means that users will need to manually enable I2C_MUX on some
distributions. Not sure about others, but, on Fedora, this option is
disabled.
So, it can end by generating a number of complains from users
that their devices suddenly stopped working after a Kernel upgrade,
at least until all distros that ship Kernels with I2C_MUX enabled.
3) if MEDIA_SUBDRV_AUTOSELECT is selected, it will select I2C and I2C_MUX.
Of course, MEDIA_SUBDRV_AUTOSELECT will need to inherit all dependencies
that I2C and I2C_MUX have (only HAS_IOMEM).
The disadvantage is that, if new dependencies are added on I2C, they'll
also need to be added here.
As the hole idea of autoselect is to let the user not bother about whatever
frontend/tuner is used by a driver, IMHO, (3) is the better solution.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There are a large number of reports that the media build is
not compiling when some drivers are compiled as builtin, while
the needed frontends are compiled as module.
On the last one of such reports:
From: kbuild test robot <fengguang.wu@intel.com>
Subject: saa7134-dvb.c:undefined reference to `zl10039_attach'
The .config file has:
CONFIG_VIDEO_SAA7134=y
CONFIG_VIDEO_SAA7134_DVB=y
# CONFIG_MEDIA_ATTACH is not set
CONFIG_DVB_ZL10039=m
And it produces all those errors:
drivers/built-in.o: In function `set_type':
tuner-core.c:(.text+0x2f263e): undefined reference to `tea5767_attach'
tuner-core.c:(.text+0x2f273e): undefined reference to `tda9887_attach'
drivers/built-in.o: In function `tuner_probe':
tuner-core.c:(.text+0x2f2d20): undefined reference to `tea5767_autodetection'
drivers/built-in.o: In function `av7110_attach':
av7110.c:(.text+0x330bda): undefined reference to `ves1x93_attach'
av7110.c:(.text+0x330bf7): undefined reference to `stv0299_attach'
av7110.c:(.text+0x330c63): undefined reference to `tda8083_attach'
av7110.c:(.text+0x330d09): undefined reference to `ves1x93_attach'
av7110.c:(.text+0x330d33): undefined reference to `tda8083_attach'
av7110.c:(.text+0x330d5d): undefined reference to `stv0297_attach'
av7110.c:(.text+0x330dbe): undefined reference to `stv0299_attach'
drivers/built-in.o: In function `tuner_attach_dtt7520x':
ngene-cards.c:(.text+0x3381cb): undefined reference to `dvb_pll_attach'
drivers/built-in.o: In function `demod_attach_lg330x':
ngene-cards.c:(.text+0x33828a): undefined reference to `lgdt330x_attach'
drivers/built-in.o: In function `demod_attach_stv0900':
ngene-cards.c:(.text+0x3383d5): undefined reference to `stv090x_attach'
drivers/built-in.o: In function `cineS2_probe':
ngene-cards.c:(.text+0x338b7f): undefined reference to `drxk_attach'
drivers/built-in.o: In function `configure_tda827x_fe':
saa7134-dvb.c:(.text+0x346ae7): undefined reference to `tda10046_attach'
drivers/built-in.o: In function `dvb_init':
saa7134-dvb.c:(.text+0x347283): undefined reference to `mt352_attach'
saa7134-dvb.c:(.text+0x3472cd): undefined reference to `mt352_attach'
saa7134-dvb.c:(.text+0x34731c): undefined reference to `tda10046_attach'
saa7134-dvb.c:(.text+0x34733c): undefined reference to `tda10046_attach'
saa7134-dvb.c:(.text+0x34735c): undefined reference to `tda10046_attach'
saa7134-dvb.c:(.text+0x347378): undefined reference to `tda10046_attach'
saa7134-dvb.c:(.text+0x3473db): undefined reference to `tda10046_attach'
drivers/built-in.o:saa7134-dvb.c:(.text+0x347502): more undefined references to `tda10046_attach' follow
drivers/built-in.o: In function `dvb_init':
saa7134-dvb.c:(.text+0x347812): undefined reference to `mt352_attach'
saa7134-dvb.c:(.text+0x347951): undefined reference to `mt312_attach'
saa7134-dvb.c:(.text+0x3479a9): undefined reference to `mt312_attach'
>> saa7134-dvb.c:(.text+0x3479c1): undefined reference to `zl10039_attach'
This is happening because a builtin module can't use directly a symbol
found on a module. By enabling CONFIG_MEDIA_ATTACH, the configuration
becomes valid, as dvb_attach() macro loads the module if needed, making
the symbol available to the builtin module.
While this bug started to appear after the patches that use IS_DEFINED
macro (like changeset 7b34be71db), this
bug is a way ancient than that.
The thing is that, before the IS_DEFINED() patches, the logic used to be:
&& defined(MODULE))
struct dvb_frontend *zl10039_attach(struct dvb_frontend *fe,
u8 i2c_addr,
struct i2c_adapter *i2c);
static inline struct dvb_frontend *zl10039_attach(struct dvb_frontend *fe,
u8 i2c_addr,
struct i2c_adapter *i2c)
{
printk(KERN_WARNING "%s: driver disabled by Kconfig\n", __func__);
return NULL;
}
The above code, with the .config file used, was evoluting to FALSE
(instead of TRUE as it should be, as CONFIG_DVB_ZL10039 is 'm'),
and were adding the static inline code at saa7134-dvb, instead
of the external call. So, while it weren't producing any compilation
error, the code weren't working either.
So, as the overhead for using CONFIG_MEDIA_ATTACH is minimal, just
enable it, if MODULES is defined.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pull media updates from Mauro Carvalho Chehab:
- Some cleanups at V4L2 documentation
- new drivers: ts2020 frontend, ov9650 sensor, s5c73m3 sensor,
sh-mobile veu mem2mem driver, radio-ma901, davinci_vpfe staging
driver
- Lots of missing MAINTAINERS entries added
- several em28xx driver improvements, including its conversion to
videobuf2
- several fixups on drivers to make them to better comply with the API
- DVB core: add support for DVBv5 stats, allowing the implementation of
statistics for new standards like ISDB
- mb86a20s: add statistics to the driver
- lots of new board additions, cleanups, and driver improvements.
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (596 commits)
[media] media: Add 0x3009 USB PID to ttusb2 driver (fixed diff)
[media] rtl28xxu: Add USB IDs for Compro VideoMate U620F
[media] em28xx: add usb id for terratec h5 rev. 3
[media] media: rc: gpio-ir-recv: add support for device tree parsing
[media] mceusb: move check earlier to make smatch happy
[media] radio-si470x doc: add info about v4l2-ctl and sox+alsa
[media] staging: media: Remove unnecessary OOM messages
[media] sh_vou: Use vou_dev instead of vou_file wherever possible
[media] sh_vou: Use video_drvdata()
[media] drivers/media/platform/soc_camera/pxa_camera.c: use devm_ functions
[media] mt9t112: mt9t111 format set up differs from mt9t112
[media] sh-mobile-ceu-camera: fix SHARPNESS control default
Revert "[media] fc0011: Return early, if the frequency is already tuned"
[media] cx18/ivtv: fix regression: remove __init from a non-init function
[media] em28xx: fix analog streaming with USB bulk transfers
[media] stv0900: remove unnecessary null pointer check
[media] fc0011: Return early, if the frequency is already tuned
[media] fc0011: Add some sanity checks and cleanups
[media] fc0011: Fix xin value clamping
Revert "[media] [PATH,1/2] mxl5007 move reset to attach"
...
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
CC: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I've always found it very confusing that the "Media ancillary drivers (tuners,
sensors, i2c, frontends)" comment came after the "Autoselect" option. This patch
moves it up and changes the "Autoselect" text to correspond more closely to
the "Media ancillary drivers" comment.
It also fixes two typos.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix a Kconfig warning that appears with allmodconfig on arm:
warning: (DVB_USB_PCTV452E) selects TTPCI_EEPROM which has unmet direct dependencies (MEDIA_SUPPORT && MEDIA_PCI_SUPPORT && MEDIA_DIGITAL_TV_SUPPORT && I2C)
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This option is a merge of both analog TV and DVB CUSTOMISE.
At the merge, the dependencies were not done right: the menu
currently appears only for analog TV. It should also be opened
for digital TV. As there are other I2C devices there (flash
devices, etc) that aren't related to either one, it is better
to make it generic enough to open for all media devices with
video.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of having 3 options to allow customizing the media
sub-drivers (tuners, I2C drivers, frontends), merge all of
them into just one.
That simplifies the life for users, as they can just keep
this untouched.
Life for developers is also simpler, as there's now just
one Kconfig item to remember, for the ancillary sub-drivers
providing supports for chips that could change from one
board design to another.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- get rid of ridden V4L2_COMMON symbol
This symbol is not needed anymore; it can be folded with V4L2
one, simplifying the Kconfig a little bit;
- Comment why some Kconfig items are needed;
- Remove if test for MEDIA_CAMERA_SUPPORT, replacing it by
depends on.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The remaining drivers are mostly platform drivers. Name the
dir to reflect it.
It makes sense to latter break it into a few other dirs.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Reorganize the API core changes for them to appear closer to
the items that enable them, and not at the drivers part of
the menu.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We should keep just the I2C drivers under drivers/media/video, and
then rename it to drivers/media/i2c.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
siano is, in fact, 2 drivers: one for MMC and one for USB, plus
a common bus-independent code. Break it accordingly.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move the tuners one level up, as the "common" directory will be used
by drivers that are shared between more than one driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
b2c2 is, in fact, 2 drivers: one for PCI and one for USB, plus
a common bus-independent code. Break it accordingly.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Raise the DVB frontends one level up, as the intention is to remove
the drivers/media/dvb directory.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
just like the V4L2 core, move the DVB core to drivers/media, as the
intention is to get rid of both "video" and "dvb" directories.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently, the v4l2 core is mixed together with other non-core drivers.
Move them into a separate directory.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Better arrange the remote controller driver items to happen after the
core support, on their proper menus, and making clerarer what is media
core options and what is media driver options.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In the past, it was possible to have either DVB or V4L2 core
as module and the other as builtin. Such config never make much
sense, and created several issues in order to make the Kconfig
dependency to work, as all drivers that depend on both (most
TV drivers) would need to be compiled as 'm'. Due to that,
the VIDEO_MEDIA config option were added.
Instead of such weird approach, let's just use the MEDIA_SUPPORT
=y or =m to select if the media subsystem core will be either
builtin or module, simplifying the building system logic.
Also, fix the tuners configuration, by enabling them only if
a tuner is required. So, if just webcam/grabbers support is
selected, no tuner option will be selected. Also, if only digital
TV is selected, no analog tuner support is selected.
That removes the need of using EXPERT customise options, when
analog TV is not selected.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Change the main items to:
<m> Multimedia support --->
[ ] Cameras/video grabbers support
[ ] Analog TV support
[ ] Digital TV support
[ ] AM/FM radio receivers/transmitters support
[ ] Remote Controller support
This provides an interface that is clearer to end users that
are compiling the Kernel, and will allow the building system
to automatically unselect drivers for unused functions.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mauro Carvalho Chehab