It has been observed that sometimes disabling the dc6 fails
and dc6 state pops back up, brief moment after disabling. This
has to be dmc save/restore timing issue or other bug in the
way dc states are handled.
Try to work around this issue as we don't have firmware fix
yet available. Verify that the value we wrote for the dmc sticks,
and also enforce it by rewriting it, if it didn't.
v2: Zero rereads on rewrite for extra paranoia (Imre)
Testcase: kms_flip/basic-flip-vs-dpms
References: https://bugs.freedesktop.org/show_bug.cgi?id=93768
Cc: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455811089-27884-1-git-send-email-mika.kuoppala@intel.com
(cherry picked from commit 779cb5d3dd)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The DMC can incorrectly run off and allow DC states on it's own. We
don't know the root-cause for this yet but this patch makes it more
visible.
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455808874-22089-2-git-send-email-mika.kuoppala@intel.com
(cherry picked from commit 832dba889e)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The assumption when adding the intel_display_power_is_enabled() checks
was that if it returns success the power can't be turned off afterwards
during the HW access, which is guaranteed by modeset locks. This isn't
always true, so make sure we hold a dedicated reference for the time of
the access.
Spotted-by: Mika Kuoppala <mika.kuoppala@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=93441
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455719489-3008-1-git-send-email-imre.deak@intel.com
(cherry picked from commit 4d80003023)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The assumption when adding the intel_display_power_is_enabled() checks
was that if it returns success the power can't be turned off afterwards
during the HW access, which is guaranteed by modeset locks. This isn't
always true, so make sure we hold a dedicated reference for the time of
the access.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1455296121-4742-13-git-send-email-imre.deak@intel.com
(cherry picked from commit ecb2448218)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The assumption when adding the intel_display_power_is_enabled() checks
was that if it returns success the power can't be turned off afterwards
during the HW access, which is guaranteed by modeset locks. This isn't
always true, so make sure we hold a dedicated reference for the time of
the access.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1455296121-4742-12-git-send-email-imre.deak@intel.com
(cherry picked from commit 5b0921748c)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The assumption when adding the intel_display_power_is_enabled() checks
was that if it returns success the power can't be turned off afterwards
during the HW access, which is guaranteed by modeset locks. This isn't
always true, so make sure we hold a dedicated reference for the time of
the access.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1455296121-4742-11-git-send-email-imre.deak@intel.com
(cherry picked from commit 3f3f42b887)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The assumption when adding the intel_display_power_is_enabled() checks
was that if it returns success the power can't be turned off afterwards
during the HW access, which is guaranteed by modeset locks. This isn't
always true, so make sure we hold a dedicated reference for the time of
the access.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1455296121-4742-10-git-send-email-imre.deak@intel.com
(cherry picked from commit 6fa9a5ecf7)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The assumption when adding the intel_display_power_is_enabled() checks
was that if it returns success the power can't be turned off afterwards
during the HW access, which is guaranteed by modeset locks. This isn't
always true, so make sure we hold a dedicated reference for the time of
the access.
While at it also add the missing reference around the HW access in
i915_interrupt_info().
v2:
- update the commit message mentioning that this also fixes the
HW access in the interrupt info debugfs entry (Daniel)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1455296121-4742-9-git-send-email-imre.deak@intel.com
(cherry picked from commit e129649b7a)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The assumption when adding the intel_display_power_is_enabled() checks
was that if it returns success the power can't be turned off afterwards
during the HW access, which is guaranteed by modeset locks. This isn't
always true, so make sure we hold a dedicated reference for the time of
the access.
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1455296121-4742-8-git-send-email-imre.deak@intel.com
(cherry picked from commit e27daab497)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The assumption when adding the intel_display_power_is_enabled() checks
was that if it returns success the power can't be turned off afterwards
during the HW access, which is guaranteed by modeset locks. This isn't
always true, so make sure we hold a dedicated reference for the time of
the access.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=93439
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1455296121-4742-7-git-send-email-imre.deak@intel.com
(cherry picked from commit 1c8fdda1ea)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The assumption when adding the intel_display_power_is_enabled() checks
was that if it returns success the power can't be turned off afterwards
during the HW access, which is guaranteed by modeset locks. This isn't
always true, so make sure we hold a dedicated reference for the time of
the access.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1455296121-4742-6-git-send-email-imre.deak@intel.com
(cherry picked from commit 4feed0ebfa)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The assumption when adding the intel_display_power_is_enabled() checks
was that if it returns success the power can't be turned off afterwards
during the HW access, which is guaranteed by modeset locks. This isn't
always true, so make sure we hold a dedicated reference for the time of
the access.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1455296121-4742-5-git-send-email-imre.deak@intel.com
(cherry picked from commit 6392f8478e)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The assumption when adding the intel_display_power_is_enabled() checks
was that if it returns success the power can't be turned off afterwards
during the HW access, which is guaranteed by modeset locks. This isn't
always true, so make sure we hold a dedicated reference for the time of
the access.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455296121-4742-4-git-send-email-imre.deak@intel.com
(cherry picked from commit 12fda3876d)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The assumption when adding the intel_display_power_is_enabled() checks
was that if it returns success the power can't be turned off afterwards
during the HW access, which is guaranteed by modeset locks. This isn't
always true, so make sure we hold a dedicated reference for the time of
the access.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Revieved-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455296121-4742-3-git-send-email-imre.deak@intel.com
(cherry picked from commit 1729050eb4)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
We have many places in the code where we check if a given display power
domain is enabled and if so access registers backed by this power
domain. We assumed that some modeset lock will prevent the power
reference from vanishing in the middle of the HW access, but this
assumption doesn't always hold. In such cases we get either the wakeref
not held, or an unclaimed register access error message. To fix this in
a future-proof way that's independent of other locks wrap any such
access with a get_ref_if_enabled()/put_ref() pair.
Kudos to Ville and Joonas for the ideas of this new interface.
v2:
- init the power_domains ptr when declaring it everywhere (Joonas)
v3:
- don't report the device to be powered if runtime PM is disabled
CC: Mika Kuoppala <mika.kuoppala@intel.com>
CC: Chris Wilson <chris@chris-wilson.co.uk>
CC: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455711462-7442-1-git-send-email-imre.deak@intel.com
(cherry picked from commit 0973128002)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Looks like g4x hpd live status bits actually agree with the spec. At
least they do on the machine I have, and apparently on Nick Bowler's
g4x as well.
So gm45 may be the only platform where they don't agree. At least
that seems to be the case based on the (somewhat incomplete)
logs/dumps in [1], and Daniel has also tested this on his gm45
sometime in the past.
So let's change the bits to match the spec on g4x. That actually makes
the g4x bits identical to vlv/chv so we can just share the code
between those platforms, leaving gm45 as the special case.
[1] https://bugzilla.kernel.org/show_bug.cgi?id=52361
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Sonika Jindal <sonika.jindal@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Nick Bowler <nbowler@draconx.ca>
References: https://lists.freedesktop.org/archives/dri-devel/2016-February/100382.html
Reported-by: Nick Bowler <nbowler@draconx.ca>
Cc: stable@vger.kernel.org
Fixes: 237ed86c69 ("drm/i915: Check live status before reading edid")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455127145-20087-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit 0780cd36c7)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
We accidentally point both cfgcr registers for the second shared DPLL to
the same location in i915_reg.h. This results in a lot of hw pipe state
mismatches whenever we try to do a modeset that requires allocating the
DPLL to a CRTC:
[drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in dpll_hw_state.cfgcr1 (expected 0x80000168, found 0x000004a5)
[drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in base.adjusted_mode.crtc_clock (expected 108000, found 49500)
[drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in port_clock (expected 108000, found 49500)
This usually ends up causing blank monitors, since the DPLL never can
get set to the right clock.
Fixes: 086f8e84a0 ("drm/i915: Prefix raw register defines with underscore")
Signed-off-by: Lyude <cpaul@redhat.com>
Cc: drm-intel-fixes@lists.freedesktop.org
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1454600601-21900-1-git-send-email-cpaul@redhat.com
(cherry picked from commit da3b891b0f)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Per spec, TPS3 support is mandatory for downstream devices that support
HBR2. We've therefore logged errors on HBR2 without TPS3 since
commit 1da7d7131c
Author: Jani Nikula <jani.nikula@intel.com>
Date: Thu Sep 3 11:16:08 2015 +0300
drm/i915: ignore link rate in TPS3 selection
However, it seems there are real world devices out there that just
aren't spec compliant, and still work at HBR2 using TPS2. So reduce the
error message to debug logging.
Cc: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Cc: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92932
Fixes: 1da7d7131c ("drm/i915: ignore link rate in TPS3 selection")
Cc: drm-intel-fixes@lists.freedesktop.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1454667370-8001-2-git-send-email-jani.nikula@intel.com
(cherry picked from commit bfcef5d213)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Our attempts save/restore panel power state in i915_suspend.c are
causing unclaimed register warnings on BXT since the registers for this
platform differ from older platforms.
The big hammer suspend/resume shouldn't be necessary for PP since the
connector/encoder hooks should already handle this. In theory we could
remove this for all platforms, but in practice it's likely that would
cause some regressions since older platforms with LVDS may have
incomplete PP handling. For now we'll leave the PCH save/restore alone
and change the non-PCH branch to only operate on gen <= 4 so that BXT
and future platforms aren't included.
v2: Typo fix: s/||/&&/
v3: Change non-PCH condition to a gen <= 4 test rather than listing
VLV/CHV/BXT as specific platforms to exclude; should be more
future-proof as we add new platforms. (Daniel)
Cc: Vandana Kannan <vandana.kannan@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: drm-intel-fixes@lists.freedesktop.org
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1452102821-17190-1-git-send-email-matthew.d.roper@intel.com
(cherry picked from commit e1ea075423)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
commit 033908aed5
Author: Dave Gordon <david.s.gordon@intel.com>
Date: Thu Dec 10 18:51:23 2015 +0000
drm/i915: mark GEM object pages dirty when mapped & written by the CPU
introduced a check into i915_gem_object_get_dirty_pages() that returned
a NULL pointer when called with a bad object, one that was not backed by
shmemfs. This WARN was too strict as we can work on all struct page
backed objects, and resulted in a WARN + GPF for existing userspace. In
order to differentiate the various types of objects, add a new flags field
to the i915_gem_object_ops struct to describe their capabilities, with
the first flag being whether the object has struct pages.
v2: Drop silly const before an integer in the structure declaration.
Testcase: igt/gem_userptr_blits/relocations
Reported-and-tested-by: Kristian Høgsberg Kristensen <krh@bitplanet.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dave Gordon <david.s.gordon@intel.com>
Cc: Kristian Høgsberg Kristensen <krh@bitplanet.net>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Kristian Høgsberg Kristensen <krh@bitplanet.net>
Tested-by: Michal Winiarski <michal.winiarski@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Fixes: 033908aed5 ("drm/i915: mark GEM object pages dirty when mapped & written by the CPU")
Link: http://patchwork.freedesktop.org/patch/msgid/1453487551-16799-1-git-send-email-chris@chris-wilson.co.uk
(cherry picked from commit de4726649b)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The test for the qemu q35 south bridge added by commit
"39bfcd52 drm/i915: more virtual south bridge detection"
also matches on real hardware. Having the check for
virtual systems last in the list is not enough to avoid
that ...
Refine the check by additionally verifying the pci
subsystem id to see whenever it *really* is qemu.
[ v2: fix subvendor tyops ]
Reported-and-tested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Bruno Wolff III <bruno@wolff.to>
Cc: drm-intel-fixes@lists.freedesktop.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453719748-10944-1-git-send-email-kraxel@redhat.com
(cherry picked from commit 1e859111c1)
Commit 5bab6f60cb ("drm/i915: Serialise updates to GGTT with access
through GGTT on Braswell") depended upon a working stop_machine() and
so forced the selection of STOP_MACHINE. However, commit 86fffe4a61
("kernel: remove stop_machine() Kconfig dependency") removed the option
STOP_MACHINE from init/Kconfig and ensured that stop_machine()
universally works. Due to the order in which the patches were applied,
removing the select from DRM_I915 got lost during merging.
Remove the now obsolete select statement.
Signed-off-by: Andreas Ziegler <andreas.ziegler@fau.de>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1453722079-2604-1-git-send-email-andreas.ziegler@fau.de
Cc: drm-intel-fixes@lists.freedesktop.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit 21fabbebff)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
On SKL+ plane scaling is mutually exclusive with color keying. The code
check for this, but during some refactoring the code got changed to
also reject primary plane windowing when color keying is used. There is
no such restriction in the hardware, so restore the original logic.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: 061e4b8d65 ("drm/i915: clean up atomic plane check functions, v2.")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1452883613-28549-1-git-send-email-ville.syrjala@linux.intel.com
Cc: stable@vger.kernel.org
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
(cherry picked from commit 693bdc28a7)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Per DP spec, the source device should fall back to 18 bpp, VESA range
RGB when the sink capability is unknown. Fix the color depth
clamping. 18 bpp color depth should ensure full color range in automatic
mode.
The clamping has been HDMI specific since its introduction in
commit 996a2239f9
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Apr 19 11:24:34 2013 +0200
drm/i915: Disable high-bpc on pre-1.4 EDID screens
Cc: stable@vger.kernel.org
Reported-and-tested-by: Dihan Wickremasuriya <nayomal@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=105331
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1452695720-7076-1-git-send-email-jani.nikula@intel.com
(cherry picked from commit 013dd9e038)
We need to set the DC FLUSH PIPE_CONTROL bit on Gen7+ to guarantee
that writes performed via the HDC are visible in memory. Fixes an
intermittent failure in a Piglit test that writes to a BO from a
shader using GL atomic counters (implemented as HDC untyped atomics)
and then expects the memory to read back the same value after mapping
it on the CPU.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91298
Tested-by: Mark Janes <mark.a.janes@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1452740379-3194-1-git-send-email-currojerez@riseup.net
(cherry picked from commit 965fd602a6)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Pull drm updates from Dave Airlie:
"This is the main drm pull request for 4.5. I don't think I've missed
anything too major, I'm mostly back at work now but I'll probably get
some sleep in 5 years time.
Summary:
New drivers:
- etnaviv:
GPU driver for the 3D core on the Vivante core used in numerous
ARM boards.
Highlights:
Core:
- Atomic suspend/resume helpers
- Move the headers to using userspace friendlier types.
- Documentation updates
- Lots of struct_mutex removal.
- Bunch of DP MST fixes from AMD.
Panel:
- More DSI helpers
- Support for some new basic panels
i915:
- Basic Kabylake support
- DP link training and detect code refactoring
- fbc/psr fixes
- FIFO underrun fixes
- SDE interrupt handling fixes
- dma-buf/fence support in pageflip path.
- GPU side for MST audio support
radeon/amdgpu:
- Drop UMS support
- GPUVM/Scheduler optimisations
- Initial Powerplay support for Tonga/Fiji/CZ/ST
- ACP audio prerequisites
nouveau:
- GK20a instmem improvements
- PCIE link speed change support
msm:
- DSI support for msm8960/apq8064
tegra:
- Host1X support for Tegra210 SoC
vc4:
- 3D acceleration support
armada:
- Get rid of struct mutex
tda998x:
- Atomic modesetting support
- TMDS clock limitations
omapdrm:
- Atomic modesetting support
- improved TILER performance
rockchip:
- RK3036 VOP support
- Atomic modesetting support
- Synopsys DW MIPI DSI support
exynos:
- Runtime PM support
- of_graph binding for DP panels
- Cleanup of IPP code
- Configurable plane support
- Kernel panic fixes at release time"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (711 commits)
drm/fb_cma_helper: Remove implicit call to disable_unused_functions
drm/amdgpu: add missing irq.h include
drm/vmwgfx: Fix a width / pitch mismatch on framebuffer updates
drm/vmwgfx: Fix an incorrect lock check
drm: nouveau: fix nouveau_debugfs_init prototype
drm/nouveau/pci: fix check in nvkm_pcie_set_link
drm/amdgpu: validate duplicates first
drm/amdgpu: move VM page tables to the LRU end on CS v2
drm/ttm: add ttm_bo_move_to_lru_tail function v2
drm/ttm: fix adding foreign BOs to the swap LRU
drm/ttm: fix adding foreign BOs to the LRU during init v2
drm/radeon: use kobj_to_dev()
drm/amdgpu: use kobj_to_dev()
drm/amdgpu/cz: force vce clocks when sclks are forced
drm/amdgpu/cz: force uvd clocks when sclks are forced
drm/amdgpu/cz: add code to enable forcing VCE clocks
drm/amdgpu/cz: add code to enable forcing UVD clocks
drm/amdgpu: fix lost sync_to if scheduler is enabled.
drm/amd/powerplay: fix static checker warning for return meaningless value.
drm/sysfs: use kobj_to_dev()
...
misc i915 fixes all over the place.
* tag 'drm-intel-next-fixes-2016-01-14' of git://anongit.freedesktop.org/drm-intel:
drm/i915/gen9: Set PIN_ZONE_4G end to 4GB - 1 page
drm/i915: Widen return value for reservation_object_wait_timeout_rcu to long.
drm/i915: intel_hpd_init(): Fix suspend/resume reprobing
drm/i915: shut up gen8+ SDE irq dmesg noise, again
drm/i915: Restore inhibiting the load of the default context
drm/i915: Tune down rpm wakelock debug checks
drm/i915: Avoid writing relocs with addresses in non-canonical form
drm/i915: Move Braswell stop_machine GGTT insertion workaround
Since your main drm-next pull isn't out of the door yet I figured I might
as well flush out drm-misc instead of delaying for 4.6. It's really just
random stuff all over, biggest thing probably connector_mask tracking from
Maarten.
* tag 'topic/drm-misc-2016-01-17' of git://anongit.freedesktop.org/drm-intel: (24 commits)
drm/fb_cma_helper: Remove implicit call to disable_unused_functions
drm/sysfs: use kobj_to_dev()
drm/i915: Init power domains early in driver load
drm: Do not set connector->encoder in drivers
apple-gmux: Add initial documentation
drm: move MODULE_PARM_DESC to other file
drm/edid: index CEA/HDMI mode tables using the VIC
drm/atomic: Remove drm_atomic_connectors_for_crtc.
drm/i915: Update connector_mask during readout, v2.
drm: Remove opencoded drm_gem_object_release_handle()
drm: Do not set outparam on error during GEM handle allocation
drm/docs: more leftovers from the big vtable documentation pile
drm/atomic-helper: Reject legacy flips on a disabled pipe
drm/atomic: add connector mask to drm_crtc_state.
drm/tegra: Use __drm_atomic_helper_reset_connector for subclassing connector state, v2.
drm/atomic: Add __drm_atomic_helper_connector_reset, v2.
drm/i915: Set connector_state->connector using the helper.
drm: Use a normal idr allocation for the obj->name
drm: Only bump object-reference count when adding first handle
drm: Balance error path for GEM handle allocation
...
Since
commit ac9b823655
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Fri Nov 27 18:55:26 2015 +0200
drm/i915: Introduce a gmbus power domain
gmbus also needs the power domain infrastructure right from the start,
since as soon as we register the i2c controllers someone can use them.
v2: Adjust cleanup paths too (Chris).
v3: Rebase onto -nightly (totally bogus tree I had lying around) and
also move dpio init head (Ville).
v4: Ville instead suggested to move gmbus setup later in the sequence,
since it's only needed by the modeset code.
v5: Move even close to the actual user, right next to the comment that
states where we really need gmbus (and interrupts!).
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Meelis Roos <mroos@linux.ee>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Fixes: ac9b823655 ("drm/i915: Introduce a gmbus power domain")
Cc: stable@vger.kernel.org
References: http://www.spinics.net/lists/intel-gfx/msg83075.html
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1452682528-19437-1-git-send-email-daniel.vetter@ffwll.ch
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Kernel and userspace are able to handle 4GB (1<<32) address space range,
but "A32 Stateless Model" is not. According to documentation, A32 accesses
are based on General State Base Address and bound checking is in place.
Because size field (instruction State Base Address) limitation, it is not
possible to address full 4GB memory region.
A32 Stateless Model is used by some libraries and without this patch, the
last page of 4GB address space is not accessible in 32bit processes.
Reported-by: Artur Harasimiuk <artur.harasimiuk@intel.com>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1452512367-23614-1-git-send-email-michel.thierry@intel.com
Cc: drm-intel-fixes@lists.freedesktop.org
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit 1892faa9ec)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This fixes a spurious warning from an integer overflow on 64-bits systems.
The function may return MAX_SCHEDULE_TIMEOUT which gets truncated to -1.
Explicitly handling this by casting to lret fixes it.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reported-and-tested-by: Joseph Yasi <joe.yasi@gmail.com>
Tested-by: Andreas Reis <andreas.reis@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: drm-intel-fixes@lists.freedesktop.org
Fixes: 3c28ff22f6 ("i915: wait for fence in prepare_plane_fb")
Link: http://patchwork.freedesktop.org/patch/msgid/5666EEC8.2000403@linux.intel.com
(cherry picked from commit bcf8be279c)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This fixes reprobing of display connectors on resume. After some
talking with danvet on IRC, I learned that calling
drm_helper_hpd_irq_event() does actually trigger a full reprobe of each
connector's status. It turns out this is the actual reason reprobing on
resume hasn't been working (this was observed on a T440s):
- We call hpd_init()
- We check each connector for a couple of things before marking
connector->polled with DRM_CONNECTOR_POLL_HPD, one of which is an
active encoder. Of course, a disconnected port won't have an
active encoder, so we don't add the flag to any of the
connectors.
- We call drm_helper_hpd_irq_event()
- drm_helper_irq_event() checks each connector for the
DRM_CONNECTOR_POLL_HPD flag. The only one that has it is eDP-1,
so we skip reprobing each connector except that one.
In addition, we also now avoid setting connector->polled to
DRM_CONNECTOR_POLL_HPD for MST connectors, since their reprobing is
handled by the mst helpers. This is probably what was originally
intended to happen here.
Changes since V1:
* Use the explanation of the issue as the commit message instead
* Change the title of the commit, since this does more then just stop a
check for an encoder now
* Add "Fixes" line for the patch that introduced this regression
* Don't enable DRM_CONNECTOR_POLL_HPD for mst connectors
Changes since V2:
* Put patch changelog above Signed-off-by
* Follow Daniel Vetter's suggestion for making the code here a bit more
legible
Fixes: 0e32b39cee ("drm/i915: add DP 1.2 MST support (v0.7)")
Cc: stable@vger.kernel.org
Signed-off-by: Lyude <cpaul@redhat.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1452181408-14777-1-git-send-email-cpaul@redhat.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit 07c5191344)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
We still keep getting
[ 4.249930] [drm:gen8_irq_handler [i915]] *ERROR* The master control interrupt lied (SDE)!
This reverts
commit 820da7ae46
Author: Jani Nikula <jani.nikula@intel.com>
Date: Wed Nov 25 16:47:23 2015 +0200
Revert "drm/i915: shut up gen8+ SDE irq dmesg noise"
which in itself is a revert, so this is just doing
commit 97e5ed1111
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Oct 23 10:56:12 2015 +0200
drm/i915: shut up gen8+ SDE irq dmesg noise
all over again. I'll stop pretending I understand what's going on like I
did when I thought I'd fixed this for good in
commit 6a39d7c986
Author: Jani Nikula <jani.nikula@intel.com>
Date: Wed Nov 25 16:47:22 2015 +0200
drm/i915: fix the SDE irq dmesg warnings properly
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Reference: http://mid.gmane.org/20151213124945.GA5715@nuc-i3427.alporthouse.com
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92084
Cc: drm-intel-fixes@lists.freedesktop.org
Fixes: 820da7ae46 ("Revert "drm/i915: shut up gen8+ SDE irq dmesg noise"")
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1452155350-14658-1-git-send-email-jani.nikula@intel.com
(cherry picked from commit 2dfb0b816d)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Following a GPU reset, we may leave the context in a poorly defined
state, and reloading from that context will leave the GPU flummoxed. For
secondary contexts, this will lead to that context being banned - but
currently it is also causing the default context to become banned,
leading to turmoil in the shared state.
This is a regression from
commit 6702cf16e0 [v4.1]
Author: Ben Widawsky <benjamin.widawsky@intel.com>
Date: Mon Mar 16 16:00:58 2015 +0000
drm/i915: Initialize all contexts
which quietly introduced the removal of the MI_RESTORE_INHIBIT on the
default context.
v2: Mark the global default context as uninitialized on GPU reset so
that the context-local workarounds are reloaded upon re-enabling.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1448630935-27377-1-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: stable@vger.kernel.org
[danvet: This seems to fix a gpu hand on after the first resume,
resulting in any future suspend operation failing with -EIO because
the gpu seems to be in a funky state. Somehow this patch fixes that.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit 42f1cae8c0)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
They're causing massive amounts of dmesg noise and hence CI noise all
over the place. Enabling them for a bit was good enough to refresh our
task list of what's still needed to enable rpm by default.
To make sure we're not forgetting to make this noisy again add a FIXME
comment.
Fixes: da5827c366 ("drm/i915: add assert_rpm_wakelock_held helper")
Cc: Imre Deak <imre.deak@intel.com>
Cc: drm-intel-fixes@lists.freedesktop.org
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1452012847-4737-1-git-send-email-daniel.vetter@ffwll.ch
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
(cherry picked from commit becd9ca2de)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
According to PRM, some parts of HW require the addresses to be in
a canonical form, where bits [63:48] == [47]. Let's convert addresses to
canonical form prior to relocating and return converted offsets to
userspace. We also need to make sure that userspace is using addresses
in canonical form in case of softpin.
v2: Whitespace fixup, gen8_canonical_addr description (Chris, Ville)
v3: Rebase on top of softpin, fix a hole in relocate_entry,
s/expect/require (Chris)
v4: Handle softpin in validate_exec_list (Chris)
v5: Convert back to canonical form at copy_to_user time (Chris)
v6: Don't use struct exec_object2 in place of exec_object
v7: Use sign_extend64 for converting to canonical form (Joonas),
reject non-canonical and non-page-aligned offset for softpin (Chris)
v8: Convert back to non-canonical form in a function,
split the test for EXEC_OBJECT_PINNED (Chris)
v9: s/canonial/canonical, drop accidental double newline (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1451409892-13708-1-git-send-email-michal.winiarski@intel.com
Testcase: igt/gem_bad_reloc/negative-reloc-blt
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92699
Cc: drm-intel-fixes@lists.freedesktop.org
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit 934acce3c0)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
drm/i915: Update connector_mask during readout, v2.
The connector_mask may be used any time during the non-atomic
.crtc_disable which is called before the full atomic state is
set up and needs to be accurate for that reason.
Changes since v1:
- Update connector_mask in readout_hw_state and add a comment.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/568D1C55.8010001@linux.intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The drm_dp_mst_topology_cbs structures are never modified, so declare them
as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The total delay of HDMI hotplug detecting with 30ms is sometimes not
enoughtfor HDMI live status up with specific HDMI monitors in BSW platform.
After doing experiments for following monitors, it needs 80ms at least
for those worst cases.
Lenovo L246 1xwA (4 failed, necessary hot-plug delay: 58/40/60/40ms)
Philips HH2AP (9 failed, necessary hot-plug delay: 80/50/50/60/46/40/58/58/39ms)
BENQ ET-0035-N (6 failed, necessary hot-plug delay: 60/50/50/80/80/40ms)
DELL U2713HM (2 failed, necessary hot-plug delay: 58/59ms)
HP HP-LP2475w (5 failed, necessary hot-plug delay: 70/50/40/60/40ms)
It looks like 70-80 ms is BSW platform needs in some bad cases of the
monitors at this end (8 times delay at most). Keep less than 100ms for
HDCP pulse HPD low (with at least 100ms) to respond a plug out.
Reviewed-by: Cooper Chiou <cooper.chiou@intel.com>
Tested-by: Gary Wang <gary.c.wang@intel.com>
Cc: Gavin Hindman <gavin.hindman@intel.com>
Cc: Sonika Jindal <sonika.jindal@intel.com>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Gary Wang <gary.c.wang@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450858295-12804-1-git-send-email-gary.c.wang@intel.com
Tested-by: Shobhit Kumar <shobhit.kumar@intel.com>
Cc: drm-intel-fixes@lists.freedesktop.org
Fixes: 237ed86c69 ("drm/i915: Check live status before reading edid")
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit f8d03ea005)
[Jani: undo the file mode change of the original commit]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This merges '5b726e06d6e8309e5c9ef4109a32caf27c71dfc8' into drm-next
Just to resolve some merges to make Daniel's life easier.
Signed-off-by: DAve Airlie <airlied@redhat.com>
Mika Kuoppala