Sending frames in CCK rates on HT can cause performance problems.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use RTS/CTS protection for TXOP on all rates modes as default and
disable CCK rates (this cause performance problems).
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Change default to RTS/CTS protection. This has a cost of transmitting
one more control frame (RTS) however protect us from traffic from
hidden node.
On station mode will use CTS-to-self if AP will configure that
for the network.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Those TX_SW_CFG1 values are used in vendor driver.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Initialize AUTO_RSP_CFG register to similar value as vendor driver does.
Do not set BAC_ACK_POLICY based on short preamble setting, those are
unrelated.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We already initlized WPDMA_GLO_CFG_WP_DMA_BURST_SIZE to 3 on
rt2800_init_registers() for USB devices. For PCI devices we will use
HW default setting, which is 2, so patch does not change behaviour
on PCI devices.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We should not reset USB_DMA_CFG on rt2800usb_init_registers() as this
function is called indirectly from rt2800_enable_radio(). If we
do so, we wipe out USB_DMA_CFG settings from rt2800usb_enable_radio().
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We should only set IEEE80211_HT_MCS_TX_RX_DIF when TX and RX MCS sets
are not equal, i.e. when number of tx streams is different than
number of RX streams.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware doesn't update beacon/Probe Response vendor IEs correctly when
bss is down, so we move brcmf_config_ap_mgmt_ie after BSS up. And host
driver should clear IEs when AP stopped so that the IEs in host side will
be synced with in firmware side.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In device removal routine, usage of "#ifdef CONFIG_RT2X00_LIB_USB"
will not cover the case when it is configured as module. This will
omit the entire if-block which does cleanup of URBs and cancellation
of pending work. Changing the #ifdef to #if IS_ENABLED() to fix it.
Signed-off-by: Vishal Thanki <vishalthanki@gmail.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since commit 6f3b911d5f ("can: bcm: add support for CAN FD frames") the
CAN broadcast manager supports CAN and CAN FD data frames.
As these data frames are embedded in struct can[fd]_frames which have a
different length the access to the provided array of CAN frames became
dependend of op->cfsiz. By using a struct canfd_frame pointer for the array of
CAN frames the new offset calculation based on op->cfsiz was accidently applied
to CAN FD frame element lengths.
This fix makes the pointer to the arrays of the different CAN frame types a
void pointer so that the offset calculation in bytes accesses the correct CAN
frame elements.
Reference: http://marc.info/?l=linux-netdev&m=147980658909653
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
ath.git patches for 4.10. Major changes:
ath9k
* add device tree bindings
* switch to use mac80211 intermediate software queues to reduce
latency and fix bufferbloat
This reverts commit 4dd1837d75.
Moving the exports for assembly code into the assembly files breaks
KSYM trimming, but also breaks modversions.
While fixing the KSYM trimming is trivial, fixing modversions brings
us to a technically worse position that we had prior to the above
change:
- We end up with the prototype definitions divorsed from everything
else, which means that adding or removing assembly level ksyms
become more fragile:
* if adding a new assembly ksyms export, a missed prototype in
asm-prototypes.h results in a successful build if no module in
the selected configuration makes use of the symbol.
* when removing a ksyms export, asm-prototypes.h will get forgotten,
with armksyms.c, you'll get a build error if you forget to touch
the file.
- We end up with the same amount of include files and prototypes,
they're just in a header file instead of a .c file with their
exports.
As for lines of code, we don't get much of a size reduction:
(original commit)
47 files changed, 131 insertions(+), 208 deletions(-)
(fix for ksyms trimming)
7 files changed, 18 insertions(+), 5 deletions(-)
(two fixes for modversions)
1 file changed, 34 insertions(+)
3 files changed, 7 insertions(+), 2 deletions(-)
which results in a net total of only 25 lines deleted.
As there does not seem to be much benefit from this change of approach,
revert the change.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Pull crypto fixes from Herbert Xu:
"The last push broke algif_hash for all shash implementations, so this
is a follow-up to fix that.
This also fixes a problem in the crypto scatterwalk that triggers a
BUG_ON with certain debugging options due to the new vmalloced-stack
code"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: scatterwalk - Remove unnecessary aliasing check in map_and_copy
crypto: algif_hash - Fix result clobbering in recvmsg
Pull thermal management fix from Zhang Rui:
"We only have one urgent fix this time.
Commit 3105f234e0 ("thermal/powerclamp: correct cpu support check"),
which is shipped in 4.9-rc3, fixed a problem introduced by commit
b721ca0d19 ("thermal/powerclamp: remove cpu whitelist").
But unfortunately, it broke intel_powerclamp driver module auto-
loading at the same time. Thus we need this change to add back module
auto-loading for 4.9"
* 'for-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal/powerclamp: add back module device table
The hci_get_route() API is used to look up local HCI devices, however
so far it has been incapable of dealing with anything else than the
public address of HCI devices. This completely breaks with LE-only HCI
devices that do not come with a public address, but use a static
random address instead.
This patch exteds the hci_get_route() API with a src_type parameter
that's used for comparing with the right address of each HCI device.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Two small fixes. One prevents timeouts on mpt3sas when trying to use
the secure erase protocol which causes the erase protocol to be
aborted. The second is a regression in a prior fix which causes all
commands to abort during PCI extended error recovery, which is
incorrect because PCI EEH is independent from what's happening on the
FC transport.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=umrF
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two small fixes.
One prevents timeouts on mpt3sas when trying to use the secure erase
protocol which causes the erase protocol to be aborted. The second is
a regression in a prior fix which causes all commands to abort during
PCI extended error recovery, which is incorrect because PCI EEH is
independent from what's happening on the FC transport"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: qla2xxx: do not abort all commands in the adapter during EEH recovery
scsi: mpt3sas: Fix secure erase premature termination
configuration and a bad frequency calculation. The other two are fixes for
passing the wrong pointer in drivers recently converted to clk_hw style
registration.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=Vr4x
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A handful of driver fixes.
The sunxi fixes are for an incorrect clk tree configuration and a bad
frequency calculation. The other two are fixes for passing the wrong
pointer in drivers recently converted to clk_hw style registration"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: efm32gg: Pass correct type to hw provider registration
clk: berlin: Pass correct type to hw provider registration
clk: sunxi: Fix M factor computation for APB1
clk: sunxi-ng: sun6i-a31: Force AHB1 clock to use PLL6 as parent
A correct bugfix introduced a harmless warning that shows up with gcc-7:
fs/nfs/callback.c: In function 'nfs_callback_up':
fs/nfs/callback.c:214:14: error: array subscript is outside array bounds [-Werror=array-bounds]
What happens here is that the 'minorversion == 0' check tells the
compiler that we assume minorversion can be something other than 0,
but when CONFIG_NFS_V4_1 is disabled that would be invalid and
result in an out-of-bounds access.
The added check for IS_ENABLED(CONFIG_NFS_V4_1) tells gcc that this
really can't happen, which makes the code slightly smaller and also
avoids the warning.
The bugfix that introduced the warning is marked for stable backports,
we want this one backported to the same releases.
Fixes: 98b0f80c23 ("NFSv4.x: Fix a refcount leak in nfs_callback_up_net")
Cc: stable@vger.kernel.org # v3.7+
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Pull scheduler fixes from Ingo Molnar:
"Two fixes for autogroup scheduling, for races when turning the feature
on/off via /proc/sys/kernel/sched_autogroup_enabled"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/autogroup: Do not use autogroup->tg in zombie threads
sched/autogroup: Fix autogroup_move_group() to never skip sched_move_task()
Pull x86 fixes from Ingo Molnar:
"Misc fixes:
- two fixes to make (very) old Intel CPUs boot reliably
- fix the intel-mid driver and rename it
- two KASAN false positive fixes
- an FPU fix
- two sysfb fixes
- two build fixes related to new toolchain versions"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/platform/intel-mid: Rename platform_wdt to platform_mrfld_wdt
x86/build: Build compressed x86 kernels as PIE when !CONFIG_RELOCATABLE as well
x86/platform/intel-mid: Register watchdog device after SCU
x86/fpu: Fix invalid FPU ptrace state after execve()
x86/boot: Fail the boot if !M486 and CPUID is missing
x86/traps: Ignore high word of regs->cs in early_fixup_exception()
x86/dumpstack: Prevent KASAN false positive warnings
x86/unwind: Prevent KASAN false positive warnings in guess unwinder
x86/boot: Avoid warning for zero-filling .bss
x86/sysfb: Fix lfb_size calculation
x86/sysfb: Add support for 64bit EFI lfb_base
Andre Noll reported panics after my recent fix (commit 34fad54c25
"net: __skb_flow_dissect() must cap its return value")
After some more headaches, Alexander root caused the problem to
init_default_flow_dissectors() being called too late, in case
a network driver like IGB is not a module and receives DHCP message
very early.
Fix is to call init_default_flow_dissectors() much earlier,
as it is a core infrastructure and does not depend on another
kernel service.
Fixes: 06635a35d1 ("flow_dissect: use programable dissector in skb_flow_dissect and friends")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andre Noll <maan@tuebingen.mpg.de>
Diagnosed-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All conflicts were simple overlapping changes except perhaps
for the Thunder driver.
That driver has a change_mtu method explicitly for sending
a message to the hardware. If that fails it returns an
error.
Normally a driver doesn't need an ndo_change_mtu method becuase those
are usually just range changes, which are now handled generically.
But since this extra operation is needed in the Thunder driver, it has
to stay.
However, if the message send fails we have to restore the original
MTU before the change because the entire call chain expects that if
an error is thrown by ndo_change_mtu then the MTU did not change.
Therefore code is added to nicvf_change_mtu to remember the original
MTU, and to restore it upon nicvf_update_hw_max_frs() failue.
Signed-off-by: David S. Miller <davem@davemloft.net>
Both of these drivers won't work on 64-bit architectures unless they
are redesigned, since they store a virtual address pointer in a 32-bit
field of the descriptors:
drivers/net/ethernet/marvell/mvneta_bm.c: In function 'mvneta_bm_construct':
drivers/net/ethernet/marvell/mvneta_bm.c:103:16: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
drivers/net/ethernet/marvell/mvpp2.c: In function 'mvpp2_prs_vlan_init':
drivers/net/ethernet/marvell/mvpp2.c:2563:32: error: large integer implicitly truncated to unsigned type [-Werror=overflow]
This limits the COMPILE_TEST option for the two drivers again to
only build them on 32-bit. This seems nicer than shutting up the
warnings, in case we ever actually want to use them on 64-bit,
as the warnings indicate which parts of the driver are currently
broken there.
Fixes: a0627f776a ("net: marvell: Allow drivers to be built with COMPILE_TEST")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko says:
====================
mlxsw: core: Implement thermal zone
Implement thermal zone for mlxsw based HW.
The first patch is just a register dependency for the second patch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement thermal zone for mlxsw based HW. It uses temperature sensor
provided by ASIC (the same as mlxsw hwmon interface) to report current
temp to thermal core. The ASIC's PWM is then used to control speed
of system fans registered as cooling devices.
Signed-off-by: Ivan Vecera <cera@cera.cz>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MFSL register is used to configure the fan speed event / interrupt
notification mechanism. Fan speed threshold are defined for both
under-speed and over-speed.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn says:
====================
Start adding support for mv88e6390
This is the first patchset implementing support for the mv88e6390
family. This is a new generation of switch devices and has numerous
incompatible changes to the registers. These patches allow the switch
to the detected during probe, and makes the statistics unit work.
These patches are insufficient to make the mv88e6390 functional. More
patches will follow.
v2:
Move stats code into global1
Change DT compatible string to mv88e6190
Fixed mv88e6351 stats which v1 had broken
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the stats functions which access global 1 registers into
global1.c.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6390 uses a different bit to select between bank0 and bank1
of the statistics. So implement an ops function for this, and pass the
selector bit to the generic stats read function. Also, the histogram
selection has moved for the mv88e6390, so abstract its selection as
well.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Different families have different sets of statistics. Abstract this
using a stats_get_stats op. The mv88e6390 needs a different
implementation, which will be added later.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Different families have different sets of statistics. Abstract this
using a stats_get_sset_count and stats_get_strings op. Each stat has a
bitmap, and the ops implementer uses a bit map mask to count the
statistics which apply for the family, or return the list of strings.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v2:
Rename functions to avoid _ prefix.
Signed-off-by: David S. Miller <davem@davemloft.net>
The statistics unit on the mv88e6390 needs the histogram mode to be
configured in a different register compared to other devices. Add an
ops to do this.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v2:
Rename to mv88e6390_g1_stats_set_histogram
Move into global1.c
Signed-off-by: David S. Miller <davem@davemloft.net>
The MV88E6390 has a control register for what the histogram statistics
actually contain. This means the stat_snapshot method should not set
this information. So implement the 6390 stats_snapshot function without
these bits.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Knowing the family of device belongs to helps with picking the ops
implementation which is appropriate to the device. So add a comment to
each structure of ops.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Taking a stats snapshot differs between same families. Abstract this
into an ops member. At the same time, move the code into global1.[ch],
since the registers are in the global1 range.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the devices added to the tables, the probe will recognize the
switch. This however is not sufficient to make it work properly, other
changes are needed because of incompatibilities.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
_mv88e6xxx_stats_wait() did not check the return value from
mv88e6xxx_g1_read(), so the compiler complained about set but unused
err.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch needs to be taken out of reset before we can read its ID
register on the MDIO bus.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While testing HDMI with Xorg on the Juno board, I find that when Xorg
starts up or shuts down, the display is shifted significantly to the
right and wrapped in the active region. (No sync bars are visible.)
The timings are correct, it behaves as if the start address has been
shifted many pixels _into_ the framebuffer.
This occurs whenever the display mode size is changed - using xrandr
in Xorg shows that changing the resolution triggers the problem
almost every time, but changing the refresh rate does not.
Using devmem2 to disable and re-enable the HDLCD resolves the issue,
and repeated disable/enable cycles do not make the issue re-appear.
Further debugging shows that we try to update the controller
configuration while enabled.
Alwys ensure that the HDLCD is disabled prior to updating the
controller timings, and use drm_crtc_vblank_off()/drm_crtc_vblank_on()
so that DRM knows whether it can expect vblank interrupts.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Group validation expects all events to be of the same PMU; however
is_uncore_pmu() is too wide, it matches _all_ uncore events, even
across PMUs.
This triggers failure when we group different events from different
uncore PMUs, like:
perf stat -vv -e '{uncore_cbox_0/config=0x0334/,uncore_qpi_0/event=1/}' -a sleep 1
Fix is_uncore_pmu() by only matching events to the box at hand.
Note that generic code; ran after this step; will disallow this
mixture of PMU events.
Reported-by: Jiri Olsa <jolsa@redhat.com>
Tested-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Kan Liang <kan.liang@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vince@deater.net>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: http://lkml.kernel.org/r/20161118125354.GQ3117@twins.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Vince Weaver reported that perf_fuzzer + KASAN detects that PEBS event
unwinds sometimes do 'weird' things. In particular, we seemed to be
ending up unwinding from random places on the NMI stack.
While it was somewhat expected that the event record BP,SP would not
match the interrupt BP,SP in that the interrupt is strictly later than
the record event, it was overlooked that it could be on an already
overwritten stack.
Therefore, don't copy the recorded BP,SP over the interrupted BP,SP
when we need stack unwinds.
Note that its still possible the unwind doesn't full match the actual
event, as its entirely possible to have done an (I)RET between record
and interrupt, but on average it should still point in the general
direction of where the event came from. Also, it's the best we can do,
considering.
The particular scenario that triggered the bogus NMI stack unwind was
a PEBS event with very short period, upon enabling the event at the
tail of the PMI handler (FREEZE_ON_PMI is not used), it instantly
triggers a record (while still on the NMI stack) which in turn
triggers the next PMI. This then causes back-to-back NMIs and we'll
try and unwind the stack-frame from the last NMI, which obviously is
now overwritten by our own.
Analyzed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Reported-by: Vince Weaver <vincent.weaver@maine.edu>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@gmail.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: davej@codemonkey.org.uk <davej@codemonkey.org.uk>
Cc: dvyukov@google.com <dvyukov@google.com>
Cc: stable@vger.kernel.org
Fixes: ca037701a0 ("perf, x86: Add PEBS infrastructure")
Link: http://lkml.kernel.org/r/20161117171731.GV3157@twins.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The following commit:
75925e1ad7 ("perf/x86: Optimize stack walk user accesses")
... switched from copy_from_user_nmi() to __copy_from_user_nmi() with a manual
access_ok() check.
Unfortunately, copy_from_user_nmi() does an explicit check against TASK_SIZE,
whereas the access_ok() uses whatever the current address limit of the task is.
We are getting NMIs when __probe_kernel_read() has switched to KERNEL_DS, and
then see vmalloc faults when we access what looks like pointers into vmalloc
space:
[] WARNING: CPU: 3 PID: 3685731 at arch/x86/mm/fault.c:435 vmalloc_fault+0x289/0x290
[] CPU: 3 PID: 3685731 Comm: sh Tainted: G W 4.6.0-5_fbk1_223_gdbf0f40 #1
[] Call Trace:
[] <NMI> [<ffffffff814717d1>] dump_stack+0x4d/0x6c
[] [<ffffffff81076e43>] __warn+0xd3/0xf0
[] [<ffffffff81076f2d>] warn_slowpath_null+0x1d/0x20
[] [<ffffffff8104a899>] vmalloc_fault+0x289/0x290
[] [<ffffffff8104b5a0>] __do_page_fault+0x330/0x490
[] [<ffffffff8104b70c>] do_page_fault+0xc/0x10
[] [<ffffffff81794e82>] page_fault+0x22/0x30
[] [<ffffffff81006280>] ? perf_callchain_user+0x100/0x2a0
[] [<ffffffff8115124f>] get_perf_callchain+0x17f/0x190
[] [<ffffffff811512c7>] perf_callchain+0x67/0x80
[] [<ffffffff8114e750>] perf_prepare_sample+0x2a0/0x370
[] [<ffffffff8114e840>] perf_event_output+0x20/0x60
[] [<ffffffff8114aee7>] ? perf_event_update_userpage+0xc7/0x130
[] [<ffffffff8114ea01>] __perf_event_overflow+0x181/0x1d0
[] [<ffffffff8114f484>] perf_event_overflow+0x14/0x20
[] [<ffffffff8100a6e3>] intel_pmu_handle_irq+0x1d3/0x490
[] [<ffffffff8147daf7>] ? copy_user_enhanced_fast_string+0x7/0x10
[] [<ffffffff81197191>] ? vunmap_page_range+0x1a1/0x2f0
[] [<ffffffff811972f1>] ? unmap_kernel_range_noflush+0x11/0x20
[] [<ffffffff814f2056>] ? ghes_copy_tofrom_phys+0x116/0x1f0
[] [<ffffffff81040d1d>] ? x2apic_send_IPI_self+0x1d/0x20
[] [<ffffffff8100411d>] perf_event_nmi_handler+0x2d/0x50
[] [<ffffffff8101ea31>] nmi_handle+0x61/0x110
[] [<ffffffff8101ef94>] default_do_nmi+0x44/0x110
[] [<ffffffff8101f13b>] do_nmi+0xdb/0x150
[] [<ffffffff81795187>] end_repeat_nmi+0x1a/0x1e
[] [<ffffffff8147daf7>] ? copy_user_enhanced_fast_string+0x7/0x10
[] [<ffffffff8147daf7>] ? copy_user_enhanced_fast_string+0x7/0x10
[] [<ffffffff8147daf7>] ? copy_user_enhanced_fast_string+0x7/0x10
[] <<EOE>> <IRQ> [<ffffffff8115d05e>] ? __probe_kernel_read+0x3e/0xa0
Fix this by moving the valid_user_frame() check to before the uaccess
that loads the return address and the pointer to the next frame.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: linux-kernel@vger.kernel.org
Fixes: 75925e1ad7 ("perf/x86: Optimize stack walk user accesses")
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Exactly because for_each_thread() in autogroup_move_group() can't see it
and update its ->sched_task_group before _put() and possibly free().
So the exiting task needs another sched_move_task() before exit_notify()
and we need to re-introduce the PF_EXITING (or similar) check removed by
the previous change for another reason.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: hartsjc@redhat.com
Cc: vbendel@redhat.com
Cc: vlovejoy@redhat.com
Link: http://lkml.kernel.org/r/20161114184612.GA15968@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The PF_EXITING check in task_wants_autogroup() is no longer needed. Remove
it, but see the next patch.
However the comment is correct in that autogroup_move_group() must always
change task_group() for every thread so the sysctl_ check is very wrong;
we can race with cgroups and even sys_setsid() is not safe because a task
running with task_group() == ag->tg must participate in refcounting:
int main(void)
{
int sctl = open("/proc/sys/kernel/sched_autogroup_enabled", O_WRONLY);
assert(sctl > 0);
if (fork()) {
wait(NULL); // destroy the child's ag/tg
pause();
}
assert(pwrite(sctl, "1\n", 2, 0) == 2);
assert(setsid() > 0);
if (fork())
pause();
kill(getppid(), SIGKILL);
sleep(1);
// The child has gone, the grandchild runs with kref == 1
assert(pwrite(sctl, "0\n", 2, 0) == 2);
assert(setsid() > 0);
// runs with the freed ag/tg
for (;;)
sleep(1);
return 0;
}
crashes the kernel. It doesn't really need sleep(1), it doesn't matter if
autogroup_move_group() actually frees the task_group or this happens later.
Reported-by: Vern Lovejoy <vlovejoy@redhat.com>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: hartsjc@redhat.com
Cc: vbendel@redhat.com
Link: http://lkml.kernel.org/r/20161114184609.GA15965@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
After patch 4efca4ed0 ("kbuild: modversions for EXPORT_SYMBOL() for asm"),
asm exports can get modversions CRCs generated if they have C definitions
in asm-prototypes.h. This patch adds missing definitions for 32 and 64 bit
allmodconfig builds.
Fixes: 9445aa1a30 ("ppc: move exports to definitions")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The aliasing check in map_and_copy is no longer necessary because
the IPsec ESP code no longer provides an IV that points into the
actual request data. As this check is now triggering BUG checks
due to the vmalloced stack code, I'm removing it.
Reported-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Recently an init call was added to hash_recvmsg so as to reset
the hash state in case a sendmsg call was never made.
Unfortunately this ended up clobbering the result if the previous
sendmsg was done with a MSG_MORE flag. This patch fixes it by
excluding that case when we make the init call.
Fixes: a8348bca29 ("algif_hash - Fix NULL hash crash with shash")
Reported-by: Patrick Steinhardt <ps@pks.im>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Stanislaw Gruszka