The driver encounters a link event ACQE with a fault code it doesn't
recognize, it logs an "Invalid" fault type and futher treats the unknown
value as a mailbox command failure. First off, there is no "invalid"
value, only values that are unknown. Secondly, the fault code doesn't
indicate status - the rest of the ACQE contains that status so there is
no reason to "fail the commands".
Change the "Invalid" to "Unknown". There is no "invalid" code value.
Separate fault code parsing and message genaration from any mbx handling
status.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In situations when the firmware image in inappropriate for the chip
type, initial validation checks were light, allowing the checks to pass,
thus allowing the firmware to be downloaded. Eventually, after the
download, the chip rejects the firmware but it is logged as a generic
firmware download error.
Revise the initial checks to validate the image vs asic type so that the
correct message is displayed and the download process is avoided.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver builds the control structures in host memory using
definitions that are based on 32-bit words. After building the structure
it is then written to the adapter.
This patch slightly optimizes LE hosts by copying the structures via
64-bit copies. This is doable as the adapter interface is LE thus there
is no byteswapping as the copy is performed.
The same optimization would be nice on BE systems, but when byteswapping
occurs, it swaps 32-bit words as well, thus trashing the control
structure. Given amount of code that is dependent upon the 32-bit word
definition, it was decided to not change things for the minor
optimization. Thus PPC 64-bit systems sticks with doing 32-bit copies.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
I/O submission paths in the lpfc nvme path are rejecting the io with an
error code that reflects back to the callee as a hard io failure. Many
of these conditions are transient and would likely resolve if retried.
Correct by returning -EBUSY, which the FC transport triggers off of to
return busy status codes to the blk-mq layer.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update the driver version to 12.0.0.2
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remote port disappearance/reappearances would cause a series of RSCN
events to be delivered to the driver. During the resulting GID_FT
handling, the driver clears the fc4 settings on the remote port, which
makes it skip registration. As such, the nvme associations eventually
fail and return io errors to the applications.
Correct by not clearng the nlp_fc4_types for all nodes in
lpfc_issue_gidft. Instead, when the GID_FT response is handled, clear
the nlp_fc4_types of FCP and NVME prior to evaluating the fc4_type
returned by the GID_FT response. This approach leaves "skipped" nodes
with their nlp_fc4_types intacted.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Points referencing local port structures didn't accommodate cases where
the localport may not be registered yet.
Add NULL pointer checks to logic.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On tests adding and removing a remote port, calls to nvme_info would
eventually show fewer target ports discovered than were present in the
san. Additionally, the following error messages were seen:
6031 RemotePort Registration failed err: -116, DID x471301
There is a race condition that exists between the driver and the nvme
transport on remote port unregister vs the confirmed deletion. It's
possible that the driver may rediscover the remote port and reregister
the remote port before a prior unregister delete callback was made (as
it rebinded to the prior remoteport structure). However, the driver was
coded to expect the callback before seeing the remote port again thus a
new registration. The logic results in the driver having an invalid
remoteport pointer set.
Correct by tracking when waiting for the delete callback. In cases where
the ndlp remoteport pointer is updated, it is only cleared when the wait
has not been superceded by a prior registration.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During target-side port faults, the driver would not recover all target
port logins. This resulted in a loss of nvme device discovery.
The driver is coded to wait for all GID_FT requests to complete before
restarting discovery. A fault is seen where the outstanding GIT_FT
counts are not properly decremented, thus discovery would never
start. Another fault was found in the clearing of the gidft_inp counter
that would be skipped in this condition. And a third fault found with
lpfc_nvme_register_port that would remove a reverence on the ndlp which
then allows a node swap on a port address change to prematurely remove
the reference and release the ndlp.
The following changes are made:
- Correct the decrementing of the outstanding GID_FT counters.
- In RSCN handling, no longer zero the counter before calling to issue
another GID_FT.
- No longer remove the reference on the dlp when the ndlp->nrport value
is not yet null.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The patch to enlarge WQ/CQ creation keys off of an adapter response that
indicates support for the larger values. Older adapters return an
incorrect response and are limited in size. Thus the adapters fail the
WQ creation steps.
Augment the WQ sizing checks with a check on the older adapter types and
limit them to the restricted sizes.
Fixes: c176ffa084 ("scsi: lpfc: Increase CQ and WQ sizes for SCSI")
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After making remoteport unregister requests, the ndlp nrport pointer was
stale.
Track when waiting for waiting for unregister completion callback and
adjust nldp pointer assignment. Add a few safety checks for NULL
pointer values.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After driver unloads, lpfc_wq remains active. The destroy_workqueue
calls were not being made in driver unload. Additionally, SLI3 is
allocating lpfc_wq resources, but never uses it.
Make the destroy_workqueue calls on driver unload. Modify the SLI3 code
path no longer allocate lpfc_wq resources.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When running loads that generated aborts, io errors where seen. Turns
out the abort requests where not placed on the proper WQ resulting in
the errors. Closer inspection inspection of this error also showed
improper spinlock api use.
Correct the WQ selection policy for the abort requests. Correct
spin_lock/spin_lock_irq/spin_lock_irqsave usage.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Under large io load, the current sizing of asynchronous buffer counts
could be exceeded, indicated by a 2885 log message:
2885 Port Status Event: port status reg 0x81800000, port smphr
reg 0xc000, error 1=0x52004a01, error 2=0x0
Enlarge the async receive queue size. Allow for a configurable number
of buffers to be posted to each RQ, using the new attribute
lpfc_nvmet_mrq_post.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When debugging various issues, per IO channel IO statistics were useful
to understand what was happening. However, many of the stats were on a
port basis rather than an io channel basis.
Move statistics to an io channel basis.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The max_scsicmpl_time parameter can be used to perform scsi cmd queue
depth mgmt based on io completion time: the queue depth is reduced to
make completion time shorter. However, as soon as an io completes and
the completion time is within limits, the code immediately bumps the
queue depth limit back up to the target queue depth. Thus the procedure
restarts, effectively limiting the usefulness of adjusting queue depth
to help completion time.
This patch makes the following changes:
- Removes the code at io completion that resets the queue depth as soon
as within limits.
- As the code removed was where the target queue depth was first
applied, change target queue depth application so that it occurs when
the parameter is changed.
- Makes target queue depth a standard parameter: both a module
parameter and a sysfs parameter.
- Optimizes the command pending count by using atomics rather than
locks.
- Updates the debugfs nodelist stats to allow better debugging of
pending command counts.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Nodelist entry for SCSI array ends up in UNMAPPED state. This is due to
illegal discovery State machine transition because of two PRLIs and the
first one failing with LS_RJT. Also, the error path was designed
assuming the PRLIs complete in the order they were sent, FCP first, then
NVME. In a failing case, the array thinks about the first PRLI (FCP),
but issues LS_RJT for the 2nd PRLI immediately.
Fix PRLI completion error path for the ordering expectation. Ensure the
discovery state machine update is not set until all outstanding PRLIs
are complete.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are several unions that are local to the source and do not need to
be in global scope, so make them static. Also add in a missing void
parameter to functions lpfc_nvme_cmd_template and
lpfc_nvmet_cmd_template to clean up non-ANSI warning.
Cleans up sparse warnings:
drivers/scsi/lpfc/lpfc_nvme.c:68:19: warning: symbol
'lpfc_iread_cmd_template' was not declared. Should it be static?
drivers/scsi/lpfc/lpfc_nvme.c:69:19: warning: symbol
'lpfc_iwrite_cmd_template' was not declared. Should it be static?
drivers/scsi/lpfc/lpfc_nvme.c:70:19: warning: symbol
'lpfc_icmnd_cmd_template' was not declared. Should it be static?
drivers/scsi/lpfc/lpfc_nvme.c:74:24: warning: non-ANSI function
'lpfc_tsend_cmd_template' was not declared. Should it be static?
drivers/scsi/lpfc/lpfc_nvmet.c:78:19: warning: symbol
'lpfc_treceive_cmd_template' was not declared. Should it be static?
drivers/scsi/lpfc/lpfc_nvmet.c:79:19: warning: symbol
'lpfc_trsp_cmd_template' was not declared. Should it be static?
drivers/scsi/lpfc/lpfc_nvmet.c:83:25: warning: non-ANSI function
declaration of function 'lpfc_nvmet_cmd_template'
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Updated Copyright in files updated as part of 12.0.0.1
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update the driver version to 12.0.0.1
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver fails to allocate command buffers in the routine
lpfc_new_scsi_buf_s4
There is an inconsistency between lpfc_mem_alloc(), where the
phba->lpfc_sg_dma_buf_pool is created, and lpfc_new_scsi_buf_s4(),
when we allocate a buffer from the pool and check the alignment. The
alignment should be on a page boundary, based on LPFC_SLI3_BG_ENABLED in
sli3_options, for both cases.
Fix by explicitly tracking sli4 vs sli3 and BG options. The result is that
phba->cfg_sg_dma_buf_size is now set correctly for SLI-4.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
POST_SGL_PAGES mailbox command failed with status (timeout).
wait_event_interruptible_timeout when called from mailbox wait interface,
gets interrupted, and will randomly fail. Behavior seems very specific to 1
particular server type.
Fix by changing from wait_event_interruptible_timeout to
wait_for_completion_timeout.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When a port is configured for NVME and SCSI Initiator support and it probes
a target supporting both SCSI and NVME, NVME devices are discovered, but
SCSI devices are not.
The nlp_fc4_type for all NPorts should be cleared on Link Up or just before
GID_FTs get issued, as opposed to just during GID_FT cmpl. RSCN activity as
well as Link Up can trigger GID_FT. One GID_FT may complete before the next
one is issued.
Fix by clearng nlp_fc4_type on link up and just before both GID_FTs are
issued. During port swapping, copy nlp_fc4_type to the new ndlp
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
To reduce latency when initializing WQE content, created templates for the
most common wqes. This reduces the number of operations taken to set the
content. It's not a lot of speed up, but every bit helps.
This patch updates the NVME target path.
[mkp: fixed typo]
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
To reduce latency when initializing WQE content, create templates for the
most common wqes. This reduces the number of operations taken to set the
content. It's not a lot of speed up, but every bit helps.
This patch updates the NVME initiator path.
[mkp: fixed typo]
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is very sloppy about the WQE structure passed between routines.
The base struct type is a 64byte wqe. But in many routines they typecast and
access 128byte wqes. There were a couple of cases in the past (corrected
already) where the typecasts were incorrectly done and the 64byte buffer was
accessed as a 128 byte buffer.
Clean this up by properly declaring wqe's as 128byte wqe's and removing the
typecasts. 64byte wqes are considered a subset of the 128byte wqes.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
First Burst support was not properly indicated in NVMe PRLI.
Correct the bit position and the logic to check and set first burst support.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 6e8e1c14c6 ("scsi: lpfc: Add WQ Full Logic for NVME Target") fails
the static checker. Checker correctly identified a missing unlock on a
return path.
Add the unlock.
Fixes: 6e8e1c14c6 ("scsi: lpfc: Add WQ Full Logic for NVME Target")
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 1351e69fc6 ("scsi: lpfc: Add push-to-adapter support to sli4")
fails compilation on some 32-bit systems as writeq() is not supported on
all architectures. Additionally, it was pointed out that as writeX()
does byteswapping if necessary for pci vs the cpu endianness, the code
was broken on BE PPC.
After discussions with Arnd Bergmann, we've resolved the issue
to the following:
Instead of writeX(), use __raw_writeX() - which writes to io
space while preserving byte order. To use this, the code
was changed to use a different buffer that lpfc prepped
via sli_pcimem_bcopy() that was set to the bytestream to
be written.
On platforms with __raw_writeq support, use the routine, otherwise
use __raw_writel()
[mkp: checkpatch]
Fixes: 1351e69fc6 ("scsi: lpfc: Add push-to-adapter support to sli4")
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Updated Copyright in files updated as part of 12.0.0.0
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update the driver version to 12.0.0.0
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The hardware offload for NVME commands was created when the
FC-NVME standard was setting SGL Descriptor Type to SGL Data
Block Descriptor (0h) and SGL Descriptor Sub Type to Address (0h).
A late change in NVMe-over-Fabrics obsoleted these values, creating
a transport SGL descriptor type with new values to go into these
fields.
For initial hardware support, in order to be compliant to the spec,
use host-supplied cmd IU buffers instead of the adapter generated
values. Later hardware will correct this.
Add a module parameter to override this offload disablement if looking
for lowest latency. This is reasonable as nothing in FC-NVME uses
the SQE SGL values.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Newer hardware more strictly enforces buffer lenghts, causing an
mis-set value to be identified. Older hardware won't catch it.
The difference is benign on old hardware.
Set the right embedded buffer length for nvme ios.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The current driver isn't taking advantage of a performance hint whereby
the initial data buffer descriptor can be placed in the WQE as well as
the SGL.
Add the logic to detect support for the feature and to use it when
supported.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Current code is very explicit in what it allows to be downloaded.
The driver checking prevented G7 firmware download. The driver
checking is unnecessary as the device will validate what it receives.
Revise the firmware download interface checking.
Added a little debug support in case there is still a failure.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Traditional SLI4 required the driver to clear Valid bits on
EQEs and CQEs after consuming them.
The new if_type=6 hardware will cycle the value for what is
valid on each queue itteration. The driver no longer has to
touch the valid bits. This also means all the cpu cache
dirtying and perhaps flush/refill's done by the hardware
in accessing the EQ/CQ elements is eliminated.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The G7 adapter supports 64G link speeds. Add support to the driver.
In addition, a small cleanup to replace the odd bitmap logic with
a switch case.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add PCI ids for the new G7 adapter
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
New if_type=6 adapters support an additional BAR that provides
apertures to allow direct WQE to adapter push support - termed
Direct Packet Push (DPP). WQ creation differs slightly to ask for
a WQ to be DPP-ized. When submitting a WQE to a DPP WQ, it is
submitted to the host memory for the WQ normally, but is also
written by the host cpu directly to a BAR aperture. Write buffer
coalescing in hardware is (hopefully) turned on, enabling single
pci write operation support. The doorbell is thing rung to indicate
the WQE is available and was pushed to the aperture.
This patch:
- Updates the WQ Create commands for the DPP options
- Adds the bar mapping for if_type=6 DPP bar
- Adds the WQE pushing to the DDP aperture received from WQ create
- Adds a new module parameter to disable DPP operation if desired.
Default is enabled.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
New hardware supports a SLI-4 interface, but with a new if_type
variant of 6.
If_type=6 has a different PCI BAR map, separate EQ/CQ doorbells,
and some changes in doorbell formats.
Add the changes for the if_type into headers, adapter initialization
and control flows. Add new eq and cq handlers.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Up until now, all SLI-4 devices had the same doorbells at the same
bar locations. With newer hardware, there are now independent EQ and
CQ doorbells and the bar locations differ.
Prepare the code for new hardware by separating the eq/cq doorbell into
separate components. The components can be set based on if_type.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Up until now, an SLI-4 device had no variance in the way it handled
its EQs and CQs. With newer hardware, there are now differences in
doorbells and some differences in how entries are valid.
Prepare the code for new hardware by creating a sli4-based callout
table that can be set based on if_type.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Updated Copyright in files updated 11.4.0.7
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update the driver version to 11.4.0.7
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In a test that is doing large numbers of cable swaps on the target, the
nvme controllers wouldn't reconnect.
During the cable swaps, the targets n_port_id would change. This
information was passed to the nvme-fc transport, in the new remoteport
registration. However, the nvme-fc transport didn't update the n_port_id
value in the remoteport struct when it reused an existing structure.
Later, when a new association was attempted on the remoteport, the
driver's NVME LS routine would use the stale n_port_id from the
remoteport struct to address the LS. As the device is no longer at that
address, the LS would go into never never land.
Separately, the nvme-fc transport will be corrected to update the
n_port_id value on a re-registration.
However, for now, there's no reason to use the transports values. The
private pointer points to the drivers node structure and the node
structure is up to date. Therefore, revise the LS routine to use the
drivers data structures for the LS. Augmented the debug message for
better debugging in the future.
Also removed a duplicate if check that seems to have slipped in.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, write underruns (mismatch of amount transferred vs scsi
status and its residual) detected by the adapter are not being flagged
as an error. Its expected the target controls the data transfer and
would appropriately set the RSP values. Only read underruns are treated
as errors.
Revise the SCSI error handling to treat write underruns as an error as
well.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver was inappropriately pulling in the nvme host's nvme.h
header. What it really needed was the standard <linux/nvme.h> header.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When using the special option to suppress the response iu, ensure the
adapter fully supports the feature by checking feature flags from the
adapter and validating the support when formatting the WQE.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During SCSI error handling escalation to host reset, the SCSI io
routines were moved off the txcmplq, but the individual io's ON_CMPLQ
flag wasn't cleared. Thus, a background thread saw the io and attempted
to access it as if on the txcmplq.
Clear the flag upon removal.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Revise the NVME PRLI to indicate CONF support.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver ignored checks on whether the link should be kept
administratively down after a link bounce. Correct the checks.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During link bounce testing in a point-to-point topology, the host may
enter a soft lockup on the lpfc_worker thread:
Call Trace:
lpfc_work_done+0x1f3/0x1390 [lpfc]
lpfc_do_work+0x16f/0x180 [lpfc]
kthread+0xc7/0xe0
ret_from_fork+0x3f/0x70
The driver was simultaneously setting a combination of flags that caused
lpfc_do_work()to effectively spin between slow path work and new event
data, causing the lockup.
Ensure in the typical wq completions, that new event data flags are set
if the slow path flag is running. The slow path will eventually
reschedule the wq handling.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Make the attribute writeable.
Remove the ramp up to logic as its unnecessary, simply set depth. Add
debug message if depth changed, possibly reducing limit, yet our
outstanding count has yet to catch up with it.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When nvme target deferred receive logic waits for exchange resources,
the corresponding receive buffer is not replenished with the hardware.
This can result in a lack of asynchronous receive buffer resources in
the hardware, resulting in a "2885 Port Status Event: ... error
1=0x52004a01 ..." message.
Correct by replenishing the buffer whenenver the deferred logic kicks
in. Update corresponding debug messages and statistics as well.
[mkp: applied by hand]
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A stress test repeatedly resetting the adapter while performing io would
eventually report I/O failures and missing nvme namespaces.
The driver was setting the nvmefc_fcp_req->private pointer to NULL
during the IO completion routine before upcalling done(). If the
transport was also running an abort for that IO, the driver would fail
the abort with message 6140. Failing the abort is not allowed by the
nvme-fc transport, as it mandates that the io must be returned back to
the transport. As that does not happen, the transport controller delete
has an outstanding reference and can't complete teardown.
The NULL-ing of the private pointer should be done only when the io is
considered complete. It's complete when the adapter returns the exchange
with the "exchange busy" flag clear.
Move the NULL'ing of the structure to the done case. This leaves the io
contexts set while it is busy and until the subsequent XRI_ABORTED
completion which returns the exchange is received.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The lpfc driver does not discover a target when the topology changes
from switched-fabric to direct-connect. The target rejects the PRLI from
the initiator in direct-connect as the driver is using the old S_ID from
the switched topology.
The driver was inappropriately clearing the VP bit to register the VPI,
which is what is associated with the S_ID.
Fix by leaving the VP bit set (it was set earlier) and as the VFI is
being re-registered, set the UPDT bit.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
I/O conditions on the nvme target may have the driver submitting to a
full hardware wq. The hardware wq is a shared resource among all nvme
controllers. When the driver hit a full wq, it failed the io posting
back to the nvme-fc transport, which then escalated it into errors.
Correct by maintaining a sideband queue within the driver that is added
to when the WQ full condition is hit, and drained from as soon as new WQ
space opens up.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Existing code was using the wrong field for the completion status when
comparing whether to increment abort statistics
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Ensure nvme localports/targetports are torn down before dismantling the
adapter sli interface on driver detachment. This aids leaving
interfaces live while nvme may be making callbacks to abort it.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Increased CQ and WQ sizes for SCSI FCP, matching those used for NVMe
development.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver controls when the hardware sends completions that communicate
consumption of elements from the WQ. This is done by setting a WQEC bit
on a WQE.
The current driver sets it on every Nth WQE posting. However, the driver
isn't clearing the bit if the WQE is reused. Thus, if the queue depth
isn't evenly divisible by N, with enough time, it can be set on every
element, creating a lot of overhead and risking CQ full conditions.
Correct by clearing the bit when not setting it on an Nth element.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Here is the set of "big" driver core patches for 4.16-rc1.
The majority of the work here is in the firmware subsystem, with reworks
to try to attempt to make the code easier to handle in the long run, but
no functional change. There's also some tree-wide sysfs attribute
fixups with lots of acks from the various subsystem maintainers, as well
as a handful of other normal fixes and changes.
And finally, some license cleanups for the driver core and sysfs code.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWnLvPw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynNzACgkzjPoBytJWbpWFt6SR6L33/u4kEAnRFvVCGL
s6ygQPQhZIjKk2Lxa2hC
=Zihy
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the set of "big" driver core patches for 4.16-rc1.
The majority of the work here is in the firmware subsystem, with
reworks to try to attempt to make the code easier to handle in the
long run, but no functional change. There's also some tree-wide sysfs
attribute fixups with lots of acks from the various subsystem
maintainers, as well as a handful of other normal fixes and changes.
And finally, some license cleanups for the driver core and sysfs code.
All have been in linux-next for a while with no reported issues"
* tag 'driver-core-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (48 commits)
device property: Define type of PROPERTY_ENRTY_*() macros
device property: Reuse property_entry_free_data()
device property: Move property_entry_free_data() upper
firmware: Fix up docs referring to FIRMWARE_IN_KERNEL
firmware: Drop FIRMWARE_IN_KERNEL Kconfig option
USB: serial: keyspan: Drop firmware Kconfig options
sysfs: remove DEBUG defines
sysfs: use SPDX identifiers
drivers: base: add coredump driver ops
sysfs: add attribute specification for /sysfs/devices/.../coredump
test_firmware: fix missing unlock on error in config_num_requests_store()
test_firmware: make local symbol test_fw_config static
sysfs: turn WARN() into pr_warn()
firmware: Fix a typo in fallback-mechanisms.rst
treewide: Use DEVICE_ATTR_WO
treewide: Use DEVICE_ATTR_RO
treewide: Use DEVICE_ATTR_RW
sysfs.h: Use octal permissions
component: add debugfs support
bus: simple-pm-bus: convert bool SIMPLE_PM_BUS to tristate
...
This is mostly updates of the usual driver suspects: arcmsr,
scsi_debug, mpt3sas, lpfc, cxlflash, qla2xxx, aacraid, megaraid_sas,
hisi_sas. We also have a rework of the libsas hotplug handling to
make it more robust, a slew of 32 bit time conversions and fixes, and
a host of the usual minor updates and style changes. The biggest
potential for regressions is the libsas hotplug changes, but so far
they seem stable under testing.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCWnH+5SYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishWxuAP0UvuJp
MNR/yU/wv/emSzOc48Ldwd7I0xD2XxSnloGUgwD+IGZZT5yNUQA1THCbm+en4hkB
WvyBieQs9qRit+2czd4=
=gJMf
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly updates of the usual driver suspects: arcmsr,
scsi_debug, mpt3sas, lpfc, cxlflash, qla2xxx, aacraid, megaraid_sas,
hisi_sas.
We also have a rework of the libsas hotplug handling to make it more
robust, a slew of 32 bit time conversions and fixes, and a host of the
usual minor updates and style changes. The biggest potential for
regressions is the libsas hotplug changes, but so far they seem stable
under testing"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (313 commits)
scsi: qla2xxx: Fix logo flag for qlt_free_session_done()
scsi: arcmsr: avoid do_gettimeofday
scsi: core: Add VENDOR_SPECIFIC sense code definitions
scsi: qedi: Drop cqe response during connection recovery
scsi: fas216: fix sense buffer initialization
scsi: ibmvfc: Remove unneeded semicolons
scsi: hisi_sas: fix a bug in hisi_sas_dev_gone()
scsi: hisi_sas: directly attached disk LED feature for v2 hw
scsi: hisi_sas: devicetree: bindings: add LED feature for v2 hw
scsi: megaraid_sas: NVMe passthrough command support
scsi: megaraid: use ktime_get_real for firmware time
scsi: fnic: use 64-bit timestamps
scsi: qedf: Fix error return code in __qedf_probe()
scsi: devinfo: fix format of the device list
scsi: qla2xxx: Update driver version to 10.00.00.05-k
scsi: qla2xxx: Add XCB counters to debugfs
scsi: qla2xxx: Fix queue ID for async abort with Multiqueue
scsi: qla2xxx: Fix warning for code intentation in __qla24xx_handle_gpdb_event()
scsi: qla2xxx: Fix warning during port_name debug print
scsi: qla2xxx: Fix warning in qla2x00_async_iocb_timeout()
...
Several statements are indented too far, fix these
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
localport is being dereferenced to assign lport and then immediately
afterwards localport is being sanity checked to see if it is null. Fix
this by only dereferencing localport until after it has been null
checked.
Detected by CoverityScan, CID#1463038 ("Dereference before null check")
Fixes: 3a8cefbfc5ee ("scsi: lpfc: Beef up stat counters for debug")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Prior patch mixed up what argument in the macro was what, so min value
was placed as the "default" argument, and the default value was placed
as the "min" argument. Thus, when the default was applied, it looked
like the default was smaller than the allowed min.
Swap argument postions to correct.
[mkp: fixed checkpatch warning]
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update the driver version to 11.4.0.6
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If log verbose in not turned on, its hard to tell when certain error
paths get hit. Add stats counters and corresponding logic to
debugfs/sysfs to aid understanding what paths were traversed.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When unregistering a remote port the lpfc driver would eventually wait
for the remoteport_unreg done callback. But the driver never completed
the io aborts that would allow the connections to terminate thus the
unreg done callback was never issued. Turns out the coding style of the
driver allowed for the wait to occur on the same cpu that the deferred
isr is called on. The blocking for the wait, blocked the isr, and as the
isr didn't run, the io aborts wouldn't finish.
Turns out there was never a good reason to block waiting for the unreg
done in the first place. The driver can continue execution and the ref
counting within the driver will do the right thing.
Resolve by removing the wait and patching up a few cases where the ref
counting didn't look right - mainly cases where the remote port comes
back before the aborts had completed and the unreg done had been
called. Additionally, a few places which used pointer values to guide
driver actions weren't protected by lock, so correct those.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In the lpfc discovery engine, when as a nvme target, where the driver
was performing mailbox io with the adapter for port login when a NVME
PRLI is received from the host. Rather than queue and eventually get
back to sending a response after the mailbox traffic, the driver
rejected the io with an error response.
Turns out this particular initiator didn't like the rejection values
(unable to process command/command in progress) so it never attempted a
retry of the PRLI. Thus the host never established nvme connectivity
with the lpfc target.
By changing the rejection values (to Logical Busy/nothing more), the
initiator accepted the response and would retry the PRLI, resulting in
nvme connectivity.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When enabled for both SCSI and NVME support, and connected pt2pt to a
SCSI only target, the driver nodelist entry for the remote port is left
in PRLI_ISSUE state and no SCSI LUNs are discovered. Works fine if only
configured for SCSI support.
Error was due to some of the prli points still reflecting the need to
send only 1 PRLI. On a lot of fabric configs, targets were NVME only,
which meant the fabric-reported protocol attributes were only telling
the driver one protocol or the other. Thus things worked fine. With
pt2pt, the driver must send a PRLI for both protocols as there are no
hints on what the target supports. Thus pt2pt targets were hitting the
multiple PRLI issues.
Complete the dual PRLI support. Track explicitly whether scsi (fcp) or
nvme prli's have been sent. Accurately track protocol support detected
on each node as reported by the fabric or probed by PRLI traffic.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Increased the sizes of the SCSI WQ's and CQ's so that SCSI operation is
similar to that used by NVME. However, size increase restricted only to
those newer adapters that can support the larger WQE size, thus bigger
queue sizes.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Handling a rcv'ed PRLI incorrectly can cause the ndlp to end up in the
wrong state or the driver to ACC and PRLI when it should send LS_RJT.
The cause was due to the driver not properly looking at the PRLI type
and taking the multiple protocol support into consideration.
Resolved by adding checks in the various PRLI receive points to validate
PRLI type and reject if not valid for the enabled protocols and mode
(host vs target).
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is all set to handle the defer_rcv api for the nvmet_fc
transport, yet didn't properly recognize the return status when the
defer_rcv occurred. The driver treated it simply as an error and aborted
the io. Several residual issues occurred at that point.
Finish the defer_rcv support: recognize the return status when the io
request is being handled in a deferred style. This stops the rogue
aborts; Replenish the async cmd rcv buffer in the deferred receive if
needed.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
NVME targets appear to randomly disconnect from the initiator when
running heavy IO.
The error is due to the host aggregate (across all controllers) io load
was beyond the maximum exchange count for nvme on the adapter. The
driver was properly returning a resource busy status, but the io load
was so great heartbeat commands would be bounced and not have a
successful retry within the fuzz amount for the nvme heartbeat (yes, a
very high io load!). Thus the target was terminating the controller due
to a keep alive failure.
Resolve by reserving a few exchanges (by counters) which can be used
when the adapter is out of normal exchanges and the command is a NVME
heartbeat command. As counters are used, while the reserved command is
outstanding, as soon as any other exchange completes, the counters are
adjusted and the reserved count is replenished. The heartbeat completes
execution in a normal fashion.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update the driver version to 11.4.0.5
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The logic for sg_seg_cnt is a bit convoluted. This patch tries to clean
up a couple of areas, especially around the +2 and +1 logic.
This patch:
- Cleans up the lpfc_sg_seg_cnt attribute to specify a real minimum
rather than making the minimum be whatever the default is.
- Removes the hardcoding of +2 (for the number of elements we use in a
sgl for cmd iu and rsp iu) and +1 (an additional entry to compensate
for nvme's reduction of io size based on a possible partial page)
logic in sg list initialization. In the case where the +1 logic is
referenced in host and target io checks, use the values set in the
transport template as that value was properly set.
There can certainly be more done in this area and it will be addressed
in combined host/target driver effort.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During driver unload, the driver may crash due to NULL pointers. The
NULL pointers were due to the driver not protecting itself sufficiently
during some of the teardown paths. Additionally, the driver was not
waiting for and cleanup up nvme io resources. As such, the driver wasn't
making the callbacks to the transport, stalling the transports
association teardown.
This patch waits for io clean up before tearding down and adds checks
for possible NULL pointers.
Cc: <stable@vger.kernel.org> # 4.12+
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When the driver is unloading, the nvme transport could be in the process
of submitting new requests, will send abort requests to terminate
associations, or may make LS-related requests. The driver's abort and
request entry points currently is ignorant of the unloading state and is
starting the requests even though the infrastructure to complete them
continues to teardown.
Change the entry points for new requests to check whether unloading and
if so, reject the requests. Abort routines check unloading, and if so,
noop the request. An abort is noop'd as the teardown paths are already
aborting/terminating the io outstanding at the time the teardown
initiated.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver's interaction with the host nvme transport has been incorrect
for a while. The driver did not wait for the unregister callbacks
(waited only 5 jiffies). Thus the driver may remove objects that may be
referenced by subsequent abort commands from the transport, and the
actual unregister callback was effectively a noop. This was especially
problematic if the driver was unloaded.
The driver now waits for the unregister callbacks, as it should, before
continuing with teardown.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver currently registers any remote port that has NVME support.
It should only be registering target ports.
Register only target ports.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During RSCN storms, the driver does not rediscover some targets. The
driver marks some RSCN as to be handled after the ones it's working
on. The driver missed processing some deferred RSCN.
Move where the driver checks for deferred RSCNs and initiate deferred
RSCN handling if the flag was set. Also revise nport state within the
RSCN confirm routine. Add some state data to a possible debug print to
aid future debugging.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
pt2pt ndlp ref count prematurely goes to 0. There was reference removed
that should only be removed if connected to a switch, not if in
point-to-point mode.
Add a mode check before the reference remove.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The current default for async hw receive queues is 1, which presents
issues under heavy load as number of queues influence the available
async receive buffer limits.
Raise the default to the either the current hw limit (16) or the number
of hw qs configured (io channel value).
Revise the attribute definition for mrq to better reflect what we do for
hw queues. E.g. 0 means default to optimal (# of cpus), non-zero
specifies a specific limit. Before this change, mrq=0 meant target mode
was disabled. As 0 now has a different meaning, rework the if tests to
use the better nvmet_support check.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Display for lpfc/fnX/iDiag/queInfo isn't formatted perfectly. Corrected
the format strings for the queue info debug messages.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver does not respond to PLOGI from the direct attach target. The
driver uses incorrect S_ID in CONFIG_LINK, after FLOGI completion
Correct by issuing CONFIG_LINK with the correct S_ID after receiving the
PLOGI from the target
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Raise the maximum NVME sg list size allowed to 256 elements.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Performing an LS abort results in the following message being seen:
0603 Invalid CQ subtype 6: 00000300 22000002 ffff0016 d0050000
and the associated exchange is not properly freed.
The code did not recognize the exchange type that was aborted, thus it
was not properly handled.
Correct by adding the NVME LS ELS type to the exchange types that are
recognized.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In test cases where an instance of the driver is detached and
reattached, the driver will crash on reattachment. There is a compound
if statement that will skip over the bar setup if the pci_resource_start
call is not successful. The driver erroneously returns success to its
bar setup in this scenario even though the bars aren't properly
configured.
Rework the offending code segment for proper initialization steps. If
the pci_resource_start call fails, -ENOMEM is now returned.
Sample stack:
rport-5:0-10: blocked FC remote port time out: removing rport
BUG: unable to handle kernel NULL pointer dereference at (null)
... lpfc_sli4_wait_bmbx_ready+0x32/0x70 [lpfc]
...
... RIP: 0010:... ... lpfc_sli4_wait_bmbx_ready+0x32/0x70 [lpfc]
Call Trace:
... lpfc_sli4_post_sync_mbox+0x106/0x4d0 [lpfc]
... ? __alloc_pages_nodemask+0x176/0x420
... ? __kmalloc+0x2e/0x230
... lpfc_sli_issue_mbox_s4+0x533/0x720 [lpfc]
... ? mempool_alloc+0x69/0x170
... ? dma_generic_alloc_coherent+0x8f/0x140
... lpfc_sli_issue_mbox+0xf/0x20 [lpfc]
... lpfc_sli4_driver_resource_setup+0xa6f/0x1130 [lpfc]
... ? lpfc_pci_probe_one+0x23e/0x16f0 [lpfc]
... lpfc_pci_probe_one+0x445/0x16f0 [lpfc]
... local_pci_probe+0x45/0xa0
... work_for_cpu_fn+0x14/0x20
... process_one_work+0x17a/0x440
Cc: <stable@vger.kernel.org> # 4.12+
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
XRI_ABORTED_CQE completions were not being handled in the fast path.
They were being queued and deferred to the lpfc worker thread for
processing. This is an artifact of the driver design prior to moving
queue processing out of the isr and into a workq element. Now that queue
processing is already in a deferred context, remove this artifact and
process them directly.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Hardware queues are a fast staging area to push commands into the
adapter. The adapter should drain them extremely quickly. However,
under heavy io load, the host cpu is pushing commands faster than the
drain rate of the adapter causing the driver to resource busy commands.
Enlarge the hardware queue (wq & cq) to support a larger number of queue
entries (4x the prior size) before backpressure. Enlarging the queue
requires larger contiguous buffers (16k) per logical page for the
hardware. This changed calling sequences that were expecting 4K page
sizes that now must pass a parameter with the page sizes. It also
required use of a new version of an adapter command that can vary the
page size values.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When the HBA is connected to a private loop, the driver reports FLOGI
loop-open failure as functional error. This is an expected condition.
Mark loop-open failure as a warning instead of error.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The error message dereferences "rqb_entry" so we need to print it first
and then free the buffer.
Fixes: 6c621a2229 ("scsi: lpfc: Separate NVMET RQ buffer posting from IO resources SGL/iocbq/context")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is mostly updates of the usual suspects: lpfc, qla2xxx, hisi_sas,
megaraid_sas, pm80xx, mpt3sas, be2iscsi, hpsa. and a host of minor
updates.
There's no major behaviour change or additions to the core in all of
this, so the potential for regressions should be small (biggest
potential being in the scsi error handler changes).
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=3O85
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly updates of the usual suspects: lpfc, qla2xxx, hisi_sas,
megaraid_sas, pm80xx, mpt3sas, be2iscsi, hpsa. and a host of minor
updates.
There's no major behaviour change or additions to the core in all of
this, so the potential for regressions should be small (biggest
potential being in the scsi error handler changes)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (203 commits)
scsi: lpfc: Fix hard lock up NMI in els timeout handling.
scsi: mpt3sas: remove a stray KERN_INFO
scsi: mpt3sas: cleanup _scsih_pcie_enumeration_event()
scsi: aacraid: use timespec64 instead of timeval
scsi: scsi_transport_fc: add 64GBIT and 128GBIT port speed definitions
scsi: qla2xxx: Suppress a kernel complaint in qla_init_base_qpair()
scsi: mpt3sas: fix dma_addr_t casts
scsi: be2iscsi: Use kasprintf
scsi: storvsc: Avoid excessive host scan on controller change
scsi: lpfc: fix kzalloc-simple.cocci warnings
scsi: mpt3sas: Update mpt3sas driver version.
scsi: mpt3sas: Fix sparse warnings
scsi: mpt3sas: Fix nvme drives checking for tlr.
scsi: mpt3sas: NVMe drive support for BTDHMAPPING ioctl command and log info
scsi: mpt3sas: Add-Task-management-debug-info-for-NVMe-drives.
scsi: mpt3sas: scan and add nvme device after controller reset
scsi: mpt3sas: Set NVMe device queue depth as 128
scsi: mpt3sas: Handle NVMe PCIe device related events generated from firmware.
scsi: mpt3sas: API's to remove nvme drive from sml
scsi: mpt3sas: API 's to support NVMe drive addition to SML
...
Pull core block layer updates from Jens Axboe:
"This is the main pull request for block storage for 4.15-rc1.
Nothing out of the ordinary in here, and no API changes or anything
like that. Just various new features for drivers, core changes, etc.
In particular, this pull request contains:
- A patch series from Bart, closing the whole on blk/scsi-mq queue
quescing.
- A series from Christoph, building towards hidden gendisks (for
multipath) and ability to move bio chains around.
- NVMe
- Support for native multipath for NVMe (Christoph).
- Userspace notifications for AENs (Keith).
- Command side-effects support (Keith).
- SGL support (Chaitanya Kulkarni)
- FC fixes and improvements (James Smart)
- Lots of fixes and tweaks (Various)
- bcache
- New maintainer (Michael Lyle)
- Writeback control improvements (Michael)
- Various fixes (Coly, Elena, Eric, Liang, et al)
- lightnvm updates, mostly centered around the pblk interface
(Javier, Hans, and Rakesh).
- Removal of unused bio/bvec kmap atomic interfaces (me, Christoph)
- Writeback series that fix the much discussed hundreds of millions
of sync-all units. This goes all the way, as discussed previously
(me).
- Fix for missing wakeup on writeback timer adjustments (Yafang
Shao).
- Fix laptop mode on blk-mq (me).
- {mq,name} tupple lookup for IO schedulers, allowing us to have
alias names. This means you can use 'deadline' on both !mq and on
mq (where it's called mq-deadline). (me).
- blktrace race fix, oopsing on sg load (me).
- blk-mq optimizations (me).
- Obscure waitqueue race fix for kyber (Omar).
- NBD fixes (Josef).
- Disable writeback throttling by default on bfq, like we do on cfq
(Luca Miccio).
- Series from Ming that enable us to treat flush requests on blk-mq
like any other request. This is a really nice cleanup.
- Series from Ming that improves merging on blk-mq with schedulers,
getting us closer to flipping the switch on scsi-mq again.
- BFQ updates (Paolo).
- blk-mq atomic flags memory ordering fixes (Peter Z).
- Loop cgroup support (Shaohua).
- Lots of minor fixes from lots of different folks, both for core and
driver code"
* 'for-4.15/block' of git://git.kernel.dk/linux-block: (294 commits)
nvme: fix visibility of "uuid" ns attribute
blk-mq: fixup some comment typos and lengths
ide: ide-atapi: fix compile error with defining macro DEBUG
blk-mq: improve tag waiting setup for non-shared tags
brd: remove unused brd_mutex
blk-mq: only run the hardware queue if IO is pending
block: avoid null pointer dereference on null disk
fs: guard_bio_eod() needs to consider partitions
xtensa/simdisk: fix compile error
nvme: expose subsys attribute to sysfs
nvme: create 'slaves' and 'holders' entries for hidden controllers
block: create 'slaves' and 'holders' entries for hidden gendisks
nvme: also expose the namespace identification sysfs files for mpath nodes
nvme: implement multipath access to nvme subsystems
nvme: track shared namespaces
nvme: introduce a nvme_ns_ids structure
nvme: track subsystems
block, nvme: Introduce blk_mq_req_flags_t
block, scsi: Make SCSI quiesce and resume work reliably
block: Add the QUEUE_FLAG_PREEMPT_ONLY request queue flag
...
This patch calls the new nvme transport routine for dev_loss_tmo
whenever the SCSI fc transport calls the lldd to make a dynamic
change to a remote ports dev_loss_tmo.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
System crashed due to a hard lockup at lpfc_els_timeout_handler+0x128.
The els ring's txcmplq list is corrupted: the last element in the list
does not point back the the head causing a loop. Issue is the els
processing path for sli4 hbas are using the hbalock instead of the
ring_lock for removing elements from the txcmplq list.
Use the adapter SLI_REV to determine which lock should be used for
removing iocbqs from the els rings txcmplq.
note: the future refactoring will address this so that we don't have
this ugly type-based lock code.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
drivers/scsi/lpfc/lpfc_debugfs.c:5460:22-29: WARNING: kzalloc should be used for phba -> nvmeio_trc, instead of kmalloc/memset
drivers/scsi/lpfc/lpfc_debugfs.c:2230:20-27: WARNING: kzalloc should be used for phba -> nvmeio_trc, instead of kmalloc/memset
Use kzalloc rather than kmalloc followed by memset with 0
Generated by: scripts/coccinelle/api/alloc/kzalloc-simple.cocci
Signed-off-by: Vasyl Gomonovych <gomonovych@gmail.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
The ! has higher precedence than the & operation. I've added
parenthesis so this works as intended.
Fixes: 952c303b32 ("scsi: lpfc: Ensure io aborts interlocked with the target.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Change version to 11.4.0.4
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The internal cfg flag is actually smaller, by 1 (for a partial page
sge), than the sg list maintained by the driver. Thus the check on sg
segments errored out when it shouldn't have
Ensure the check is +1
Note: having a value that is less than what it really is is bogus.
Correcting it now would be a significant rework. Add this item to the
list to be refactored in the merge with efct.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When running NVME io as a NVME host, if the driver is unloaded there
would be oops in lpfc_sli4_issue_wqe.
When unloading, controllers are torn down and the transport initiates
set_property commands to reset the controller and issues aborts to
terminate existing io. The drivers nvme abort and fcp io submit
routines needed to recognize the driver is unloading and fail the new
requests. It didn't, resulting in the oops.
Revise the ls and fcp io submit routines to detect the unloading state
and properly handle their cleanup.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Support RDP and Multiple Frames
If the remote Nport is not logged in, the driver would not populate all
the descriptors in the RDP response payload. Doing so would create a
payload length that requires multiple frames due to exceeding the
default rx buffer size without an explicit login. Currently FC-LS
explicitly states the RDP response must be a single frame sequence.
Thus we did not violate the standard.
Recently, a modification to FC-LS was accepted which allows multi-frame
sequences and all vendors have indicated they are interoperable with the
change. As such, extend RDP support with the additional fields and send
a multi-frame sequence.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Before releasing nvme io back to the io stack for possible retry on
other paths, ensure the io termination is interlocked with the target
device by ensuring the entire ABTS-LS protocol is complete.
Additionally, FC-NVME ABTS-LS protocol does not use RRQ. Remove RRQ
behavior from ABTS-LS.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Firmware update fails with: status x17 add_status x56 on the final write
If multiple DMA buffers are used for the download, some firmware revs
have difficulty with signatures and crcs split across the dma buffer
boundaries. Resolve by making all writes be a single 4k page in length.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is seeing a NULL pointer in lpfc_nvme_fcp_io_submit. This
was ultimately due to a transport AER being sent on a terminated
controller, thus some of the values were not set. In case we're in a
system without a corrected transport and in case a race condition occurs
where we enter the routine as the teardown is happening in a separate
thread, validate the parameters before starting the io.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The initial implementation of NVME didn't merge with NPIV support. As
such, there are several issues if NPIV is used with NVME. For now,
ensure that if NVME is enabled then NPIV is not enabled.
Support for NPIV with NVME will be added in the near future.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
if nvmet targetport registration fails, the driver encounters a NULL
pointer oops in lpfc_hb_timeout_handler.
To fix: if registration fails, ensure nvmet_support is cleared on the
port structure.
Also enhanced the log message on failure.
Cc: <stable@vger.kernel.org> # 4.12+
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The descriptions for lpfc_xri_split and lpfc_enable_fc4_type were
poor. Revise for better understanding:
lpfc_xri_split - Percentage of FCP XRI resources versus NVME
lpfc_enable_fc4_type - Enable FC4 Protocol support - FCP / NVME
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Always set ctxp->state to LPFC_NVMET_STE_ABORT if ABORT op gets called
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are several log messages that report abnormal terminations that by
default are marked warn. These are typically the result of failures due
to invalid controller state or abort completions. They are all natural
when a controller resets.
Unfortunately, as they are logged by default, it makes the admin very
concerned.
Convert the messages to Info.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is encountering oops in lpfc_sli_calc_ring.
The driver is setting hba_wqidx for FCP based on the policy in use for
NVME. The two may not be the same. Change to set the wqidx based on the
FCP policy.
Cc: <stable@vger.kernel.org> # 4.12+
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Under heavy target nvme load duration, the lpfc irq handler is
encountering cpu lockup warnings.
Convert the driver to a shortened ISR handler which identifies the
interrupting condition then schedules a workq thread to process the
completion queue the interrupt was for. This moves all the real work
into the workq element.
As nvmet_fc upcalls are no longer in ISR context, don't set the feature
flags
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Need to make ktime samples more accurate
If ktime is turned on in the middle of an IO, the max calculation could
be misleading. Base sampling on the start time of the IO as opposed to
ktime_on.
Make ISR ktime timestamps be from when CQE is read instead of EQE.
Added additional sanity checks when deciding whether to accept an IO
sample or not.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Local Reject/Invalid RPI errors seen during discovery.
Temporary RPI cleanup was occurring regardless of SLI rev. It's only
necessary on SLI-4.
Adjust the test for whether cleanup is necessary.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Warning messages when NVME_TARGET_FC not defined on ppc builds
The lpfc_nvmet_replenish_context() function is only meaningful when NVME
target mode enabled. Surround the function body with ifdefs for target
mode enablement.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In a link bounce scenario, a condition can occur where the discovery
engine swaps an ndlp structure (address change for an nport). While the
swap was successfully executed by the discovery engine, the driver did
not properly detect a change in the ndlp bound to the nvme rport. This
error resulted in the nvme host transport issuing an IO to the correct
nvme rport, but the lpfc driver addressed a ndlp with an NLP_UNUSED
status and failed the io. This resulting it it looking like there were
missing namespaces and applications failed due to io errors.
To fix, in lpfc_nvme_register_rport, rework the "rebind" case to break
the nvme rport<->ndlp association when the ndlp already has an
nrport. Then rebind the rport to the correct ndlp data and backpointers.
[mkp: typo]
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver crashes when attempting to use a freed ndpl pointer.
The pci_remove_one handler runs on a separate kernel thread. The order
of the removal is starting by freeing all of the ndlps and then
disabling interrupts. In between these two events the driver can still
receive an ELS and process it. When it tries to use the ndlp pointer
will be NULL
Change the order of the pci_remove_one vs disable interrupts so that
interrupts are disabled before the ndlp's are freed.
Cc: <stable@vger.kernel.org> # 4.12+
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During pci hot plug, the kernel crashes in a list_add_call
The lookup by tag function will return null if the IOCB is out of range
or does not have the on txcmplq flag set.
Fix: Check for null return from lookup by tag.
Cc: <stable@vger.kernel.org> # 4.12+
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During pci hot plug, the kernel crashes in timer management code.
The sli4 remove_one handler is not stoping the timers as it starts to
remove the port so that it can be swapped.
Fix: Stop the timers early in the handler routine.
Note: Fix in SLI-4 only. SLI-3 already stopped the timers properly.
Cc: <stable@vger.kernel.org> # 4.12+
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Eight mostly minor fixes for recently discovered issues in drivers.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=v2G5
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Eight mostly minor fixes for recently discovered issues in drivers"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ILLEGAL REQUEST + ASC==27 => target failure
scsi: aacraid: Add a small delay after IOP reset
scsi: scsi_transport_fc: Also check for NOTPRESENT in fc_remote_port_add()
scsi: scsi_transport_fc: set scsi_target_id upon rescan
scsi: scsi_transport_iscsi: fix the issue that iscsi_if_rx doesn't parse nlmsg properly
scsi: aacraid: error: testing array offset 'bus' after use
scsi: lpfc: Don't return internal MBXERR_ERROR code from probe function
scsi: aacraid: Fix 2T+ drives on SmartIOC-2000
Use *_pool_zalloc rather than *_pool_alloc followed by memset with 0.
Found by coccinelle spatch "api/alloc/pool_zalloc-simple.cocci"
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The lpfc driver uses the FC-specific error when it needed to return an
error to the FC-NVME transport. Convert to use a generic value instead.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Internal error codes happen to be positive, thus the PCI driver core
won't treat them as failure, but we do. This would cause a crash later
on as lpfc_pci_remove_one() is called (e.g. as shutdown function).
Fixes: 6d368e5321 ("[SCSI] lpfc 8.3.24: Add resource extent support")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The pointer eqe is always non-null inside the while loop, so the check
to see if eqe is NULL is redudant and hence can be removed.
Detected by CoverityScan CID#1248693 ("Logically Dead Code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is mostly updates of the usual suspects: lpfc, qla2xxx, hisi_sas, megaraid_sas, zfcp and a host of minor updates.
The major driver change here is the elimination of the block based
cciss driver in favour of the SCSI based hpsa driver (which now drives
all the legacy cases cciss used to be required for). Plus a reset
handler clean up and the redo of the SAS SMP handler to use bsg lib.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=nQUG
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly updates of the usual suspects: lpfc, qla2xxx, hisi_sas,
megaraid_sas, zfcp and a host of minor updates.
The major driver change here is the elimination of the block based
cciss driver in favour of the SCSI based hpsa driver (which now drives
all the legacy cases cciss used to be required for). Plus a reset
handler clean up and the redo of the SAS SMP handler to use bsg lib"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (279 commits)
scsi: scsi-mq: Always unprepare before requeuing a request
scsi: Show .retries and .jiffies_at_alloc in debugfs
scsi: Improve requeuing behavior
scsi: Call scsi_initialize_rq() for filesystem requests
scsi: qla2xxx: Reset the logo flag, after target re-login.
scsi: qla2xxx: Fix slow mem alloc behind lock
scsi: qla2xxx: Clear fc4f_nvme flag
scsi: qla2xxx: add missing includes for qla_isr
scsi: qla2xxx: Fix an integer overflow in sysfs code
scsi: aacraid: report -ENOMEM to upper layer from aac_convert_sgraw2()
scsi: aacraid: get rid of one level of indentation
scsi: aacraid: fix indentation errors
scsi: storvsc: fix memory leak on ring buffer busy
scsi: scsi_transport_sas: switch to bsg-lib for SMP passthrough
scsi: smartpqi: remove the smp_handler stub
scsi: hpsa: remove the smp_handler stub
scsi: bsg-lib: pass the release callback through bsg_setup_queue
scsi: Rework handling of scsi_device.vpd_pg8[03]
scsi: Rework the code for caching Vital Product Data (VPD)
scsi: rcu: Introduce rcu_swap_protected()
...
This is an interesting regression with gcc-8, showing a harmless warning
for correct code:
In file included from include/linux/kernel.h:13:0,
...
from drivers/scsi/lpfc/lpfc_debugfs.c:23:
include/linux/printk.h:301:2: error: 'eq' may be used uninitialized in this function [-Werror=maybe-uninitialized]
printk(KERN_ERR pr_fmt(fmt), ##__VA_ARGS__)
^~~~~~
In file included from drivers/scsi/lpfc/lpfc_debugfs.c:58:0:
drivers/scsi/lpfc/lpfc_debugfs.h:451:31: note: 'eq' was declared here
I managed to reduce the warning into a small test case for gcc-8 that I
reported in the gcc bugzilla[1].
As a workaround, this changes the logic to move the two assignments of
'eq' out of the conditions and instead make the index conditional. This
works for all configurations I tried and avoids adding a bogus
initialization.
Acked-by: James Smart <james.smart@broadcom.com>
Link: [1] https://gcc.gnu.org/bugzilla/show_bug.cgi?id=81958
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The only reference to lpfc_nvmet_replenish_context() is inside of an
disabled:
drivers/scsi/lpfc/lpfc_nvmet.c:1457:1: error: 'lpfc_nvmet_replenish_context' defined but not used [-Werror=unused-function]
This replaces the preprocessor conditional with a C condition, so the
compiler can see that the function is intentionally unused.
Fixes: 9a38e4f1c82f ("scsi: lpfc: Fix MRQ > 1 context list handling")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update driver version to 11.4.0.3
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
cc1: warnings being treated as errors
drivers/scsi/lpfc/lpfc_init.c: In function 'lpfc_get_wwpn':
drivers/scsi/lpfc/lpfc_init.c:3253: error: integer constant is too large for 'long' type
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add Buffer to buffer credit recovery support to the driver. This is a
negotiated feature with the peer that allows for both sides to detect
dropped RRDY's and FC Frames and recover credit.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Change hw queue binding messages to info - not error.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Port issue was fixed, the hbacmd reset would take more than 8 minutes to
complete.
There were conflicting NVME SGL posting/reposting responsibilities
between lpfc_online()/lpfc_sli4_hba_setup() and
lpfc_nvme_create_localport(). The lpfc_online() causes a REPOST on
existing NVME SGLs which is not released during the fc port reset.
However, lpfc_nvme_create_localport() wants to allocate new NVME buffers
and post them. Both cancelled out each other which had a side effect of
hosing the mailbox handling that was used to remove the sgl lists -
causing multiple 60s mbx timeouts.
Fix by preserving all SGL lists over the fc port reset.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The nonrecovery occurred because the lpfc nvme initiator function did
not reestablish its localport creation with the nvme host transport in
lpfc_oneline. Because of that, an NVME rport binding could not take
place.
Corrected by recreating the localport in the adapter reset recovery
routine.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If the nvmet_fc transport breaks an io into multiple sequences, the
driver will improperly set the relative offset on the 2nd through N
sequences.
Correct by properly formatting the hw cmd so the relative offset is
picked up from the hw cmd.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Various oops including cpu LOCKUPs were seen.
For asynchronously received ius where the driver must assign exchange
resources, the resources were on a single get (free) list and put list
(finished, waiting to be put on get list). As all cpus are sharing the
lists, an interrupt for a receive frame may have to wait for all the
other cpus to place their done work onto the put list before it can
acquire the lock to pull from the list.
Fix by breaking the resource lists into per-cpu lists or at least more
than 1 list with cpu's sharing the lists). A cpu would allocate from the
free list for its own cpu, and put its done work on the its own put list
- avoiding the contention. As cpu load may vary, when empty, a cpu may
grab from another cpu, thereby changing resource distribution. But
searching for a resource only occurs on 1 or a few cpus until a single
resource can be allocated. if the condition reoccurs, it starts looking
at a different cpu.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Various oops being seen on being in the ISR too long and cpu lockups,
when under heavy load.
The amount of work being posted off of completion queues kept the ISR
running almost all the time
Correct the issue by limiting the amount of work per iteration.
[mkp: typo]
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When using fabric-assigned WWNs, the switch doesn't like copy of the
FLOGI payload, which includes valid VVL bits, to be used as the FDISC
payload.
Rather than wait for corrected switch firmware, ensure the VVL bits are
marked invalid on FDISCs.
[mkp: typo]
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A race condition was found whereby the initiator would receive the RSCN
for a new NVME device before it had a chance to register its FC4 support
with the fabric. Thus, when queried by the initiator, it would see that
the target supported FC-NVME.
Corrected by making the assumption that the target always supports
FC-NVME thus a PRLI is sent. It's ok for the target to reject it.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In adapter reset tests, an oops was seen with a NULL pointer in
lpfc_free_rq_buffer+0x20/0x60
The driver is failing to properly repost the nvmet sgl list when
recovering from the reset. Thus the driver eventually trys to walk an
errant buffer list.
Corrected the sgl buffer recovery as well as strengthening the
initialization of the bufferlist.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After lip, the driver sometimes would have two rports for the same
device, allowing the namespaces to be duplicated by nvme.
In lpfc_plogi_confirm_nport() the driver was not swapping the nrport
maintained by the ndlp's undergoing address swapping. This allowed the
2nd rport to sneak in as it was considered a separate device.
This patch adds the fixes to Swap the nrport in each ndlp and take care
of the reference counts on the ndlps similar to FCP rports.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After link bounce in a NVME Pt2Pt config, the driver managed to map the
same nport twice, resulting in multiple device nodes for the same
namespace.
In Pt2Pt, the driver must send PRLI's for both (scsi) FCP and NVME
rather than using fabric aids. The driver was inconsistent on handling
various PRLI completions, especially rejects, which had reject codes
cross the different protocol PRLI completions.
Fixed to perform the following: if nvmet mode (fc port can only be a
nvme target) - rejects all unsolicitly FCP PRLI's. Never issues a FCP
PRLI.
The multiple protocol PRLI's are sent simultaneously. However, driver
will now only state transition after both PRLI's are complete. New flags
were added to aid tracking the responses from the different PRLI's.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Modify driver return error codes to align with host nvme transport.
Driver isn't returning Exxx error codes to properly reflect out of
resource or connectivity conditions (-EBUSY), yet there were hard error
conditions returning -EBUSY.
Ensure the following situations return the proper return code:
- Temporary failures or temporary resource availability: -EBUSY
- Connectivity issues: -ENODEV
All others are treated as hard errors and return an -Exxx value that
indicates the type of error.
Also, lpfc_sli4_issue_wqe() was modified to not translate error from
-Exxx to WQE state. This allows lpfc_nvme_fcp_io_submit() routine to
just return whatever -E value was returned from other routines.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Transitioned some informational discovery messages to now always be
displayed when log_verbose is set.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
lpfc oops when it discovers a NVME target but is configured for SCSI
only operation. Oops is in lpfc_nvme_register_port+0x33/0x300.
The localport is not valid so it should not have been referenced.
Added validity check for localport
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When the switch blade is pulled out then plugged back in, the driver
does not issue a PLOGI to the target
When the switch blade is pulled out, it does not reset the link. The
driver ends up issuing a LOGO to the target, and finally sees devloss.
Since the driver believes that a LOGO is outstanding, it does not issue
a PLOGI to the target upon link up
Correct by placing the ndlp in UNUSED state When devloss happens in
LOGO_ISSUE state.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver does not discover targets when in loop mode.
The NLP type is correctly getting set when a fabric connection is
detected but, not for loop. The unknown NLP type means that the driver
does not issue a PRLI when in loop topology. Thus target discovery
fails.
Fix by checking the topology during discovery. If it is loop, set the
NLP FC4 type to FCP.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Message "0271 Illegal State Transition: node" seen in logs, all luns are
unuseable for that target.
A window exists in the rcv_plogi path where if the state is plogi issue
but the driver has not issued a plogi, then two reglogins will be sent
for the same RPI. The first one to complete will advance the state to
prli issue the second one will be detected as an illegal state, and
leave the node in an unusable state.
Correct the completion routine for the PLOGI ACC that detects the state
change when the driver starts discovery on the node again and drop the
REGLOGIN mailbox command.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove variable assignments. The value stored in local variable _rc_ is
overwritten at line 2448:rc = lpfc_sli4_bsg_set_link_diag_state(phba,
0); before it can be used.
Addresses-Coverity-ID: 1226935
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, calls to nvmet_fc_rcv_fcp_req() always copied the
FC-NVME cmd iu to a temporary buffer before returning, allowing
the driver to immediately repost the buffer to the hardware.
To address timing conditions on queue element structures vs async
command reception, the nvmet_fc transport occasionally may need to
hold on to the command iu buffer for a short period. In these cases,
the nvmet_fc_rcv_fcp_req() will return a special return code
(-EOVERFLOW). In these cases, the LLDD must delay until the new
defer_rcv lldd callback is called before recycling the buffer back
to the hw.
This patch adds support for the new nvmet_fc transport defer_rcv
callback and recognition of the new error code when passing commands
to the transport.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The PCI pool API is deprecated. This commit replaces the PCI pool old
API by the appropriate function with the DMA pool API. It also updates
some comments, accordingly.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Reviewed-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pull more block updates from Jens Axboe:
"This is a followup for block changes, that didn't make the initial
pull request. It's a bit of a mixed bag, this contains:
- A followup pull request from Sagi for NVMe. Outside of fixups for
NVMe, it also includes a series for ensuring that we properly
quiesce hardware queues when browsing live tags.
- Set of integrity fixes from Dmitry (mostly), fixing various issues
for folks using DIF/DIX.
- Fix for a bug introduced in cciss, with the req init changes. From
Christoph.
- Fix for a bug in BFQ, from Paolo.
- Two followup fixes for lightnvm/pblk from Javier.
- Depth fix from Ming for blk-mq-sched.
- Also from Ming, performance fix for mtip32xx that was introduced
with the dynamic initialization of commands"
* 'for-linus' of git://git.kernel.dk/linux-block: (44 commits)
block: call bio_uninit in bio_endio
nvmet: avoid unneeded assignment of submit_bio return value
nvme-pci: add module parameter for io queue depth
nvme-pci: compile warnings in nvme_alloc_host_mem()
nvmet_fc: Accept variable pad lengths on Create Association LS
nvme_fc/nvmet_fc: revise Create Association descriptor length
lightnvm: pblk: remove unnecessary checks
lightnvm: pblk: control I/O flow also on tear down
cciss: initialize struct scsi_req
null_blk: fix error flow for shared tags during module_init
block: Fix __blkdev_issue_zeroout loop
nvme-rdma: unconditionally recycle the request mr
nvme: split nvme_uninit_ctrl into stop and uninit
virtio_blk: quiesce/unquiesce live IO when entering PM states
mtip32xx: quiesce request queues to make sure no submissions are inflight
nbd: quiesce request queues to make sure no submissions are inflight
nvme: kick requeue list when requeueing a request instead of when starting the queues
nvme-pci: quiesce/unquiesce admin_q instead of start/stop its hw queues
nvme-loop: quiesce/unquiesce admin_q instead of start/stop its hw queues
nvme-fc: quiesce/unquiesce admin_q instead of start/stop its hw queues
...
This is mostly updates of the usual suspects: lpfc, qla2xxx, bnx2fc,
qedf, hpsa, hisi_sas, smartpqi, cxlflash, aacraid, csiostor along with
a host of minor and miscellaneous changes.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=D9QX
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly updates of the usual suspects: lpfc, qla2xxx, bnx2fc,
qedf, hpsa, hisi_sas, smartpqi, cxlflash, aacraid, csiostor along with
a host of minor and miscellaneous changes"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (276 commits)
qla2xxx: Fix NVMe entry_type for iocb packet on BE system
scsi: qla2xxx: avoid unused-function warning
scsi: snic: fix a couple of spelling mistakes/typos
scsi: qla2xxx: fix a bunch of typos and spelling mistakes
scsi: lpfc: don't double count abort errors
scsi: lpfc: spin_lock_irq() is not nestable
scsi: hisi_sas: optimise DMA slot memory
scsi: ibmvfc: constify dev_pm_ops structures.
scsi: ibmvscsi: constify dev_pm_ops structures.
scsi: cxlflash: Update debug prints in reset handlers
scsi: cxlflash: Update send_tmf() parameters
scsi: cxlflash: Avoid double free of character device
scsi: Add STARGET_CREATED_REMOVE state to scsi_target_state
scsi: ses: do not add a device to an enclosure if enclosure_add_links() fails.
scsi: ufs: flush eh_work when eh_work scheduled.
scsi: qla2xxx: Protect access to qpair members with qpair->qp_lock
scsi: sun_esp: fix device reference leaks
scsi: fnic: changing queue command to return result DID_IMM_RETRY when rport is init
scsi: fnic: correct speed display and add support for 25,40 and 100G
scsi: fnic: added timestamp reporting in fnic debug stats
...
Pull misc user access cleanups from Al Viro:
"The first pile is assorted getting rid of cargo-culted access_ok(),
cargo-culted set_fs() and field-by-field copyouts.
The same description applies to a lot of stuff in other branches -
this is just the stuff that didn't fit into a more specific topical
branch"
* 'work.misc-set_fs' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
Switch flock copyin/copyout primitives to copy_{from,to}_user()
fs/fcntl: return -ESRCH in f_setown when pid/pgid can't be found
fs/fcntl: f_setown, avoid undefined behaviour
fs/fcntl: f_setown, allow returning error
lpfc debugfs: get rid of pointless access_ok()
adb: get rid of pointless access_ok()
isdn: get rid of pointless access_ok()
compat statfs: switch to copy_to_user()
fs/locks: don't mess with the address limit in compat_fcntl64
nfsd_readlink(): switch to vfs_get_link()
drbd: ->sendpage() never needed set_fs()
fs/locks: pass kernel struct flock to fcntl_getlk/setlk
fs: locks: Fix some troubles at kernel-doc comments
If lpfc_nvmet_unsol_fcp_issue_abort() fails then we accidentally
increment "tgtp->xmt_abort_rsp_error" and then two lines later we
increment it a second time.
Fixes: 547077a44b ("scsi: lpfc: Adding additional stats counters for nvme.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We're calling spin_lock_irq() multiple times, the problem is that on the
first spin_unlock_irq() then we will re-enable IRQs and we don't want
that.
Fixes: 966bb5b711 ("scsi: lpfc: Break up IO ctx list into a separate get and put list")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A change in remote port removal introduced a spurious put which can
cause a premature structure teardown. The affects were most notable when
the driver attempted to unload as a null pointer would be hit.
Fix by removing the unnecessary put.
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On link down, transport is calling driver to abort outstanding ios.
Driver erroneously rejects the abort if the port indicates it isn't
logged in - which will be the case after the link down. Thus, the io
can't clean up. This prevents reconnection at the transport level.
Fix by allowing abort to proceed.
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Set lpfc driver revision to 11.4.0.1
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Beacon OFF from switch is rejected by driver.
Driver fails Beacon OFF if frequency is set to 0. As per fc-ls spec,
status, capability, frequency and duration fields are only applicable
for Beacon ON.
Remove frequency and type checks. Reject Beacon ON if duration is non
zero.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When running nvme detach-ns /dev/nvme0n1 -n 1 command, the nvmet lpfc
driver crashes with this stack dump:
kernel BUG at /root/NVME/lpfc_8.4/lpfc_sli.c:1393!
invalid opcode: 0000 [#1] SMP
Workqueue: nvmet-fc-cpu0 nvmet_fc_do_work_on_cpu [nvmet_fc]
lpfc_sli4_issue_wqe+0x357/0x440 [lpfc]
lpfc_nvmet_xmt_fcp_abort+0x36b/0x5c0 [lpfc]
nvmet_fc_abort_op+0x30/0x50 [nvmet_fc]
nvmet_fc_do_work_on_cpu+0xd9/0x130 [nvmet_fc]
process_one_work+0x14e/0x410
worker_thread+0x116/0x490
kthread+0xc7/0xe0
ret_from_fork+0x3f/0x70
Crash is due to an uninitialized iocbq->vport pointer.
Explicitly set the iocbq->vport field to phba->pport in
lpfc_nvmet_sol_fcp_issue_abort as it does all abort iocbq initialization
in the routine. Using phba->pport is ok because target does not support
NPIV instances.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During every reset, IOCBs are allocated. So, at one point, number of
allocated IOCBs reaches maximum limit and lpfc_sli_next_iotag fails.
Allocate IOCBs only during initialization. Reuse them after every reset
instead of allocating new set of IOCBs.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
OS crashes after the completion of firmware download.
Failure in posting SCSI SGL buffers because number of SGL buffers is
less than total count. Some of the pending IOs are not completed by
driver. SGL buffers for these IOs are not added back to the list.
Pending IOs are not completed because lpfc_wq_list list is initialized
before completion of pending IOs.
Postpone lpfc_wq_list reinitialization by moving
lpfc_sli4_queue_destroy() after lpfc_hba_down_post().
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In a server with an 8G adapter and a 32G adapter, running NVME and FCP,
the server would crash with the following stack.
RIP: 0010: ... lpfc_nvme_register_port+0x38/0x420 [lpfc]
lpfc_nlp_state_cleanup+0x154/0x4f0 [lpfc]
lpfc_nlp_set_state+0x9d/0x1a0 [lpfc]
lpfc_cmpl_prli_prli_issue+0x35f/0x440 [lpfc]
lpfc_disc_state_machine+0x78/0x1c0 [lpfc]
lpfc_cmpl_els_prli+0x17c/0x1f0 [lpfc]
lpfc_sli_sp_handle_rspiocb+0x39b/0x6b0 [lpfc]
lpfc_sli_handle_slow_ring_event_s3+0x134/0x2d0 [lpfc]
lpfc_work_done+0x8ac/0x13b0 [lpfc]
lpfc_do_work+0xf1/0x1b0 [lpfc]
Crash, on the 8G adapter, is due to a vport which does not have a nvme
local port structure. It's not supposed to have one. NVME is not
supported on the 8G adapter, so the NVME PRLI, which started this flow
shouldn't have been sent in the first place.
Correct discovery engine to recognize when on an SLI3 rport, which
doesn't support SLI3, if the rport supports only NVME, don't send a NVME
PRLI. Instead, as no FC4 will be used, a LOGO is sent. If rport is FCP
and NVME, only execute the SCSI PRLI.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since unsol rcv ISR and command cmpl ISR both access/lock this list,
separate get/put lists will reduce contention.
Replaced
struct list_head lpfc_nvmet_ctx_list;
with
struct list_head lpfc_nvmet_ctx_get_list;
struct list_head lpfc_nvmet_ctx_put_list;
and all correpsonding locks and counters.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Removed unnecessary bzero of context area. Due to size of sg list, added
a substantial delay and played havoc on cpu caches.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Vport creation fails for SLI-3 adapters.
Mailbox submission fails because mailbox interrupt is disabled. Mailbox
interrupt is disabled during port reset.
Do reset only for physical port.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
First line of nvme_info output is not consistent. There is an Extra
colon in the format.
First line of output will contain one of the following strings:
NVME Initiator Enabled
NVME Target Enabled
NVME Disabled
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is a null pointer dereference that can happen in the FOF interrupt
handler.
The driver was not setting up cq->assoc_qp_for sli4_hba->oas_cq.
Initialize cq->assoc_qp before accessing it.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Set lpfc driver revision to 11.4.0.0
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Administrator intervention is currently required to get good numbers
when switching from running latency tests to IOPS tests.
The configured interrupt coalescing values will greatly effect the
results of these tests. Currently, the driver has a single coalescing
value set by values of the module attribute. This patch changes the
driver to support auto-configuration of the coalescing value based on
the total number of outstanding IOs and average number of CQEs processed
per interrupt for an EQ. Values are checked every 5 seconds.
The driver defaults to the automatic selection. Automatic selection can
be disabled by the new lpfc_auto_imax module_parameter.
Older hardware can only change interrupt coalescing by mailbox
command. Newer hardware supports change via a register. The patch
support both.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Addressed the following reported defects:
** CID 1411552: Control flow issues (MISSING_BREAK)
/drivers/scsi/lpfc/lpfc_sli.c: 13259 in lpfc_sli4_nvmet_handle_rcqe()
** CID 1411553: Memory - illegal accesses (OVERRUN)
/drivers/scsi/lpfc/lpfc_sli.c: 16218 in lpfc_fc_frame_check()
** CID 1411553: Memory - illegal accesses (OVERRUN)
Overrunning array "lpfc_rctl_names" of 202 8-byte elements at element
index 244 (byte offset 1952) using index "fc_hdr->fh_r_ctl" (which
evaluates to 244).
** CID 1411554: Null pointer dereferences (REVERSE_INULL)
/drivers/scsi/lpfc/lpfc_nvmet.c: 2131 in lpfc_nvmet_unsol_fcp_abort_cmp()
** CID 1411555: Memory - illegal accesses (UNINIT)
/drivers/scsi/lpfc/lpfc_nvmet.c: 180 in lpfc_nvmet_ctxbuf_post()
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
vports cannot login to target.
For vports, lpfc_nodelist is allocated for targets only on completion of
GFF_ID command. Driver checks if lpfc_nodelist exists for target before
sending GFF_ID. So, GFF_ID and PLOGI are not sent.
As mentioned by the comment in lpfc_prep_node_fc4type() routine, do not
send GFF_ID only if this NPortID is previously identified as FCP
target. Send GFF_ID if it is a newly identified remote port from GID_FT
response.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The nvmet driver was rejecting the initiator's PRLI because its reg_rpi
for the PLOGI was still outstanding. The initiator would resend the
PRLI without delay and get the same answer. The PRLI retries would
exhaust causing the nvme initiator to set the nvmet ndlp to UNMAPPED.
The driver's lpfc_els_retry handler did not have a policy for an LS_RJT
with explanation CMD_IN_PROGRESS for PRLI or NVME_PRLI. This caused the
delay to remain at 0 but retry set 1.
Fix: When the ELS response is LS_RJT, TPC and the command was PRLI or
NVME_PRLI, just set the delay to 1000 mS to get a 1 second delay on the
PRLI retry. This was enough to allow the REG_RPI to complete at the
target.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Kernel panic when log_verbose is set to 0xffffffff
phba->pport is dereferenced before it is initialized
Fix: Do not dereference phba->pport if it is NULL
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
System panic with general protection fault during driver load
The driver uses a static array sli4_hba.handler_name to store the irq
handler names. If the io_channel_irqs exceeds the pre-allocated size
(32+1), then the driver will overwrite other fields of sli4_hba.
Fix: Dynamically allocate handler_name.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Null pointer dereference when BFS VM is powered off
The driver incorrectly uses sli3_ring on SLI-4 adapters
Use the correct ring structure based on sli_rev
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Tested-by: Raphael Silva <raphasil@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On hbacmd reset failure, observing wrong string "nline" in kernel log.
On failure, non negative value (1) is returned from sysfs store
routine. It is interpreted as count by kernel and store routine is
called again with the remaining characters as input.
Fix: Return negative error code (-EIO) in case of failure.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
NVME FC counters don't reflect actual results
Since counters are not atomic, or protected by a lock, the values often
get screwed up.
Make them atomic, like NVMET. Fix up sysfs and debugfs display
accordingly Added Outstanding IOs to stats display
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Observing lpfc port down after issuing hbacmd reset command
Failure in posting SGL buffers. If there is only one SGL buffer and rrq
is valid for its XRI, we are rightly returning NULL but not adding the
buffer back to the SGL list. So, number of buffers become less than
total count and repost fails during reset.
Add SGL buffer back to list before returning NULL.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When unloading the driver, the NVMET driver would wait the full 30
seconds for its UNMAPPED initiator node to get removed before continuing
with the unload process. NVMEI worked correctly.
For each rport put into UNMAPPED or MAPPED state by NVMET, the driver
puts a reference on the NDLP. The difference is that NVMEI has a
unregister call for its rports and the extra reference is removed in the
unregister process. For NVMET, the driver has to remove the reference
explicitly when dropping out of UNMAPPED or MAPPED because there is no
unregister call.
Add a call to lpfc_nlp_put on the ndlp when NVMET and the old state was
UNMAPPED or MAPPED.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Lun Priority level shown as NA
Remote port is not getting registered for nameserver and fdmi. Due to
which dfc SendCTPassThru cmd is failing.
Made changes to register the remote port for both.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Inconsistent error messages and context state checks
Context state sanity checks were not accurate or inconsistent in the
code paths.
Separated LS context states from FCP.
Added and modified context state sanity checks.
Use context state to determine if a sol or unsol ABORT is needed.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While debugging Devloss and recovery, debugfs and sysfs were found to
not show the NVME port roles consistently.
The port role FC_PORT_ROLE_NVME_DISCOVERY was added with the devloss
bringup and the other issues were just oversight.
Add NVME Target and DISCSRVC to debugfs nodeinfo and sysfs nvme info
handlers. The full port role was added to the NVME data only not the
generic nodelist.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
As the devloss API was implemented in the nvmei driver, an evaluation of
the nvme transport and the lpfc driver showed dual management of the
rports. This creates a bug possibility when the thread count and SAN
size increases.
The nvmei driver code was based on a very early transport and was not
revisited until the devloss API was introduced.
Remove the listhead in the driver's rport data structure and the
listhead in the driver's lport data structure. Remove all rport_list
traversal. Convert the driver to use the nrport (nvme rport) pointer
that is now NULL or nonNULL depending on a devloss action. Convert
debugfs and nvme_info in sysfs to use the fc_nodes list in the vport.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add nvme initiator devloss support
The existing implementation was based on no devloss behavior in the
transport (e.g. immediate teardown) so code didn't properly handle
delayed nvme rport device unregister calls. In addition, the driver was
not correctly cycling the rport port role for each
register-unregister-reregister process.
This patch does the following:
Rework the code to properly handle rport device unregister calls and
potential re-allocation of the remoteport structure if the port comes
back in under dev_loss_tmo.
Correct code that was incorrectly cycling the rport port role for each
register-unregister-reregister process.
Prep the code to enable calling the nvme_fc transport api to dynamically
update dev_loss_tmo when the scsi sysfs interface changes it.
Memset the rpinfo structure in the registration call to enforce "accept
nvme transport defaults" in the registration call. Driver parameters do
influence the dev_loss_tmo transport setting dynamically.
Simplifies the register function: the driver was incorrectly searching
its local rport list to determine resume or new semantics, which is not
valid as the transport already handles this. The rport was resumed if
the rport handed back matches the ndlp->nrport pointer. Otherwise,
devloss fired and the ndlp's nrport is NULL.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
functions lpfc_nvmet_cleanup_io_context and lpfc_nvmet_setup_io_context
can be made static as they do not need to be in global scope.
Cleans up sparse warnings:
"warning: symbol 'lpfc_nvmet_cleanup_io_context' was not declared.
Should it be static?"
"warning: symbol 'lpfc_nvmet_setup_io_context' was not declared.
Should it be static?"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Trivial fix to spelling mistake in debugfs message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is a set of user visible fixes (excepting one format string
change). Four of the qla2xxx fixes only affect the firmware dump
path, but it's still important to the enterprise. The rest are
various NULL pointer crash conditions or outright driver hangs.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABAgAGBQJZPGMCAAoJEAVr7HOZEZN4jekQAJN1x7WIB4HuI3EoHSSMej8h
bdssAbqQn/H++nIJ/e6ZRHKt0P6ngSzXuIb4lwbOJUQa7sxEWaWDeXywPEqjDYqP
BBjloYOrAff492uYXL48xjG4Xl4qOxb8GfKT7iFptIzAdk/2Rxhj56XqlhY7IMSG
ut4binbz+3v0NEKnI6od+uxvXAc6EumyF0zW9a4rbjK/wAukciRIGWkOrsQpa8cJ
VdgUsMdbpjTlYbMnPfHa+oUqKkWir3PI9rQ01AvMUugrqAXiAPLgoHFB6H8eVVn7
vzVnJd31RoUrv6JNnWcRsi0VWsciPw5XBpd6VRVjZUdOlUds3vW7n1G2ut5TfAAp
sYkFSuhxcWgp3QJpqDbS/l976dXyfdzhQpahgYLbRAuhoi8HDmcpwzTdWC9a41tw
k2sqAbgZd60ZHu8OSrD2HqJrkMqSXzklMkZMS33nfE1Ki7c+aWHImby4P+lEKIIw
nJCiVc3yO+TcWvdH5w+6Fu/nA0HJ9OcFEk1P+4Xz38n5o/WcduoXG6NgpVT+mKXO
zQZDEYbWQYixDEs1m8fJpTHu5p2tXYzdMS9L/Fa0B2MQ3kY9XIT41rHqnJPBOp2R
wKXksIyzQagW6r0bQ2lFkth0elLHGxDlwfCDgrN6zQFrdBcpRfT+GdTDpDWiWggt
qgIbBvEO4sd12V5miQsK
=jZXV
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of user visible fixes (excepting one format string
change).
Four of the qla2xxx fixes only affect the firmware dump path, but it's
still important to the enterprise. The rest are various NULL pointer
crash conditions or outright driver hangs"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: cxgb4i: libcxgbi: in error case RST tcp conn
scsi: scsi_debug: Avoid PI being disabled when TPGS is enabled
scsi: qla2xxx: Fix extraneous ref on sp's after adapter break
scsi: lpfc: prevent potential null pointer dereference
scsi: lpfc: Avoid NULL pointer dereference in lpfc_els_abort()
scsi: lpfc: nvmet_fc: fix format string
scsi: qla2xxx: Fix crash due to NULL pointer dereference of ctx
scsi: qla2xxx: Fix mailbox pointer error in fwdump capture
scsi: qla2xxx: Set bit 15 for DIAG_ECHO_TEST MBC
scsi: qla2xxx: Modify T262 FW dump template to specify same start/end to debug customer issues
scsi: qla2xxx: Fix crash due to mismatch mumber of Q-pair creation for Multi queue
scsi: qla2xxx: Fix NULL pointer access due to redundant fc_host_port_name call
scsi: qla2xxx: Fix recursive loop during target mode configuration for ISP25XX leaving system unresponsive
scsi: bnx2fc: fix race condition in bnx2fc_get_host_stats()
scsi: qla2xxx: don't disable a not previously enabled PCI device
Null check at line 966: if (ndlp) {, implies that ndlp might be NULL.
Functions lpfc_nlp_set_state() and lpfc_issue_els_prli() dereference
pointer ndlp. Include these function calls inside the IF block that
tests pointer ndlp.
Addresses-Coverity-ID: 1401856
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We might have a NULL pring in lpfc_els_abort(), for example on error
recovery path, since queues are destroyed during error recovery
mechanism.
In this case, we should just drop the abort since the queues will be
recreated anyway. This patch just verifies for NULL pointer and stop the
abortion of the queue in case of a NULL pring.
Also, this patch converts return type of lpfc_els_abort() from int to
void, since it's not checked anywhere.
Reported-by: Harsha Thyagaraja <hathyaga@in.ibm.com>
Reported-by: Naresh Bannoth <nbannoth@in.ibm.com>
Tested-by: Raphael Silva <raphasil@linux.vnet.ibm.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The lpfc_nvmeio_data() tracing helper always takes a format string and
three additional arguments. The latest caller has a format string with
only two integer arguments, causing this harmless warning:
drivers/scsi/lpfc/lpfc_nvmet.c: In function 'lpfc_nvmet_xmt_fcp_release':
drivers/scsi/lpfc/lpfc_nvmet.c:802:25: error: too many arguments for format [-Werror=format-extra-args]
lpfc_nvmeio_data(phba, "NVMET FCP FREE: xri x%x ste %d\n", ctxp->oxid,
We could add a dummy argument here, but it seems reasonable to print
the 'abort' flag as the third argument.
Fixes: 19b58d9473 ("nvmet_fc: add req_release to lldd api")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is quite a big update because it includes a rework of the lpfc
driver to separate the NVMe part from the FC part. The reason for
doing this is because two separate trees (the nvme and scsi trees
respectively) want to update the individual components and this
separation will prevent a really nasty cross tree entanglement by the
time we reach the next merge window. The rest of the fixes are the
usual minor sort with no significant security implications.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=NtGp
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is quite a big update because it includes a rework of the lpfc
driver to separate the NVMe part from the FC part.
The reason for doing this is because two separate trees (the nvme and
scsi trees respectively) want to update the individual components and
this separation will prevent a really nasty cross tree entanglement by
the time we reach the next merge window.
The rest of the fixes are the usual minor sort with no significant
security implications"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (25 commits)
scsi: zero per-cmd private driver data for each MQ I/O
scsi: csiostor: fix use after free in csio_hw_use_fwconfig()
scsi: ufs: Clean up some rpm/spm level SysFS nodes upon remove
scsi: lpfc: fix build issue if NVME_FC_TARGET is not defined
scsi: lpfc: Fix NULL pointer dereference during PCI error recovery
scsi: lpfc: update version to 11.2.0.14
scsi: lpfc: Add MDS Diagnostic support.
scsi: lpfc: Fix NVMEI's handling of NVMET's PRLI response attributes
scsi: lpfc: Cleanup entry_repost settings on SLI4 queues
scsi: lpfc: Fix debugfs root inode "lpfc" not getting deleted on driver unload.
scsi: lpfc: Fix NVME I+T not registering NVME as a supported FC4 type
scsi: lpfc: Added recovery logic for running out of NVMET IO context resources
scsi: lpfc: Separate NVMET RQ buffer posting from IO resources SGL/iocbq/context
scsi: lpfc: Separate NVMET data buffer pool fir ELS/CT.
scsi: lpfc: Fix NMI watchdog assertions when running nvmet IOPS tests
scsi: lpfc: Fix NVMEI driver not decrementing counter causing bad rport state.
scsi: lpfc: Fix nvmet RQ resource needs for large block writes.
scsi: lpfc: Adding additional stats counters for nvme.
scsi: lpfc: Fix system crash when port is reset.
scsi: lpfc: Fix used-RPI accounting problem.
...
James Smart