If a OPP table is defined for the GPU device in the device tree use
that in lieu of the downstream style GPU frequency table. If we do
use the downstream table convert it to a OPP table so that we can
take advantage of the OPP lookup facilities later.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Some A3XX and A4XX GPU targets required that the GPU clock be
programmed to a non zero value when it was disabled so
27Mhz was chosen as the "invalid" frequency.
Even though newer targets do not have the same clock restrictions
we still write 27Mhz on clock disable and expect the clock subsystem
to round down to zero.
For unknown reasons even though the slow clock speed is always
27Mhz and it isn't actually a functional level the legacy device tree
frequency tables always defined it and then did gymnastics to work
around it.
Instead of playing the same silly games just hard code the "slow" clock
speed in the code as 27MHz and save ourselves a bit of infrastructure.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
User space needs to know where the GMEM whole starts so that they
can set up the addressing correctly.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
There are reasons for a memory object to outlive the file descriptor
that created it and so the address space that a buffer object is
attached to must also outlive the file descriptor. Reference count
the address space so that it can remain viable until all the objects
have released their addresses.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We should be detaching the MMU before destroying the address
space. To do this cleanly, the detach has to happen in
adreno_gpu_cleanup() because it needs access to structs
in adreno_gpu.c. Plus it is better symmetry to have
the attach and detach at the same code level.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The interrupt status was being cleared before processing the handlers.
a5xx_rbbm_err_irq() was checking the interrupt status again, which would
likely turn out bad because the interrupt status would be 0 (or at least
different). Pass the original status to the function instead.
Also, skip clearing RBBM_AHB_ERROR from the interrupt status. The interrupt
will keep firing until the error source is cleared. Skip the clear to
avoid a storm until the error is cleared in a5xx_rbbm_err_irq().
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Instead of checking for a5xx_gpu->gpmu_iova during destroy we
accidently check a5xx_gpu->gpmu_bo.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The newly added a5xx support fails to build when debugfs is diabled:
drivers/gpu/drm/msm/adreno/a5xx_gpu.c:849:4: error: 'struct msm_gpu_funcs' has no member named 'show'
drivers/gpu/drm/msm/adreno/a5xx_gpu.c:849:11: error: 'a5xx_show' undeclared here (not in a function); did you mean 'a5xx_irq'?
This adds a missing #ifdef.
Fixes: b5f103ab98 ("drm/msm: gpu: Add A5XX target support")
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Each of the per-generation callbacks was doing this. Lets just simplify
and move it into toplevel show() fxn.
Signed-off-by: Rob Clark <robdclark@gmail.com>
This was never documented or used in upstream dtb. It is used by
downstream bindings from android device kernels. But the quirks are
a property of the gpu revision, and as such are redundant to be listed
separately in dt. Instead, move the quirks to the device table.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
The original way we determined the gpu version was based on downstream
bindings from android kernel. A cleaner way is to get the version from
the compatible string.
Note that no upstream dtb uses these bindings. But the code still
supports falling back to the legacy bindings (with a warning), so that
we are still compatible with the gpu dt node from android device
kernels.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Acked-by: Rob Herring <robh@kernel.org>
The plan is to use the OPP bindings. For now, remove the documentation
for qcom,gpu-pwrlevels, and make the driver fall back to a safe low
clock if the node is not present.
Note that no upstream dtb use this node. For now we keep compatibility
with this node to avoid breaking compatibility with downstream android
dt files.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Acked-by: Rob Herring <robh@kernel.org>
Fixes: 9cb07b099fb ("drm/msm: support multiple address spaces")
Reported-by: Riku Voipio <riku.voipio@linaro.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Currently the value written to CP_RB_WPTR is calculated on the fly as
(rb->next - rb->start). But as the code is designed rb->next is wrapped
before writing the commands so if a series of commands happened to
fit perfectly in the ringbuffer, rb->next would end up being equal to
rb->size / 4 and thus result in an out of bounds address to CP_RB_WPTR.
The easiest way to fix this is to mask WPTR when writing it to the
hardware; it makes the hardware happy and the rest of the ringbuffer
math appears to work and there isn't any point in upsetting anything.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
[squash in is_power_of_2() check]
Signed-off-by: Rob Clark <robdclark@gmail.com>
Most 5XX targets have GPMU (Graphics Power Management Unit) that
handles a lot of the heavy lifting for power management including
thermal and limits management and dynamic power collapse. While
the GPMU itself is optional, it is usually nessesary to hit
aggressive power targets.
The GPMU firmware needs to be loaded into the GPMU at init time via a
shared hardware block of registers. Using the GPU to write the microcode
is more efficient than using the CPU so at first load create an indirect
buffer that can be executed during subsequent initalization sequences.
After loading the GPMU gets initalized through a shared register
interface and then we mostly get out of its way and let it do
its thing.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Disable the interrupt during the init sequence to avoid having
interrupts fired for errors and other things that we are not
ready to handle while initializing.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add helper functions for TYPE4 and TYPE7 ME opcodes that replace
TYPE0 and TYPE3 starting with the A5XX targets.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add a new generic function to write a "64" bit value. This isn't
actually a 64 bit operation, it just writes the upper and lower
32 bit of a 64 bit value to a specified LO and HI register. If
a particular target doesn't support one of the registers it can
mark that register as SKIP and writes/reads from that register
will be quietly dropped.
This can be immediately put in place for the ringbuffer base and
the RPTR address. Both writes are converted to use
adreno_gpu_write64() with their respective high and low registers
and the high register appropriately marked as SKIP for both 32 bit
targets (a3xx and a4xx). When a5xx comes it will define valid target
registers for the 'hi' option and everything else will just work.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add some new functions to manipulate GPU registers. gpu_read64 and
gpu_write64 can read/write a 64 bit value to two 32 bit registers.
For 4XX and older these are normally perfcounter registers, but
future targets will use 64 bit addressing so there will be many
more spots where a 64 bit read and write are needed.
gpu_rmw() does a read/modify/write on a 32 bit register given a mask
and bits to OR in.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
When the GPU hardware init function fails (like say, ME_INIT timed
out) return error instead of blindly continuing on. This gives us
a small chance of saving the system before it goes boom.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
There are very few register accesses in the common code. Cut down
the list of common registers to just those that are used. This
saves const space and saves us the effort of maintaining registers
for A3XX and A4XX that don't exist or are unused.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
For a5xx the gpu is 64b so we need to change iova to 64b everywhere. On
the display side, iova is still 32b so it can ignore the upper bits.
(Although all the armv8 devices have an iommu that can map 64b pa to 32b
iova.)
Signed-off-by: Rob Clark <robdclark@gmail.com>
We can have various combinations of 64b and 32b address space, ie. 64b
CPU but 32b display and gpu, or 64b CPU and GPU but 32b display. So
best to decouple the device iova's from mmap offset.
Signed-off-by: Rob Clark <robdclark@gmail.com>
We get 2 warnings when building kernel with W=1:
drivers/gpu/drm/msm/adreno/a3xx_gpu.c:535:17: warning: no previous prototype for 'a3xx_gpu_init' [-Wmissing-prototypes]
drivers/gpu/drm/msm/adreno/a4xx_gpu.c:624:17: warning: no previous prototype for 'a4xx_gpu_init' [-Wmissing-prototypes]
In fact, both functions are declared in
drivers/gpu/drm/msm/adreno/adreno_device.c, but should be declared
in a header file. So this patch moves both function declarations to
drivers/gpu/drm/msm/adreno/adreno_gpu.h.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1477127865-9381-1-git-send-email-baoyou.xie@linaro.org
For some optimizations coming on the userspace side, splitting larger
draw or gmem cmds into multiple cmdstream buffers, we need to support
much more than the previous small/arbitrary limit.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Before we can add vmap shrinking, we really need to know which vmap'ings
are currently being used. So switch to get/put interface. Stubbed put
fxns for now.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Some, but not all, callers of obj->vmap() would check if return
IS_ERR(). So let's actually return an error if vmap() fails. And fixup
the call-sites that were not handling this properly.
Signed-off-by: Rob Clark <robdclark@gmail.com>
At this point, there is nothing left to fail. And submit already has a
fence assigned and is added to the submit_list. Any problems from here
on out are asynchronous (ie. hangcheck/recovery).
Signed-off-by: Rob Clark <robdclark@gmail.com>
It is no longer true that we discard all in-flight submits on recover
(these days we only discard the first one that hung). After the first
re-submitted batch completes it would overwrite the fence with a correct
value, but there would be a window of time which showed all re-submitted
batches as already complete.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Better encapsulate the per-timeline stuff into fence-context. For now
there is just a single fence-context, but eventually we'll also have one
per-CRTC to enable fully explicit fencing.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Not sure where it came from, but seem unintentional. And also not
needed on a420, so let's just drop it.
Signed-off-by: Rob Clark <robdclark@gmail.com>
We need this for GL_TIMESTAMP queries.
Note: currently only supported on a4xx.. a3xx doesn't have this
always-on counter. I think we could emulate it with the one CP
counter that is available, but for now it is of limited usefulness
on a3xx (since we can't seem to do time-elapsed queries in any sane
way with the existing firmware on a3xx, and if you are trying to do
profiling on a tiler you want time-elapsed). We can add that later
if it becomes useful.
Signed-off-by: Rob Clark <robdclark@gmail.com>
As described in the downstream/kgsl driver:
Sometimes the RPTR shadow memory is unreliable causing timeouts
in adreno_idle(). Read it directly from the register instead.
Signed-off-by: Craig Stout <cstout@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We need this in userspace for interpreting some of the perf ctrs.
Note possibly not quite sufficient if we had some frequency mgmt
approach other than race-to-idle. Not really sure what the best
thing to do if we did. Although displaying results as a percentage
of max frequence seems sensible(ish) if we did.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Remove CONFIG_OF checks in adreno_device.c. The downstream bus scaling
stuff is included only when CONFIG_OF is not set. So, remove that too.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
As found in apq8016 (used in DragonBoard 410c) and msm8916.
Note that numerically a306 is actually 307 (since a305c already claimed
306). Nice and confusing.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Jordan Crouse