Although brcmfmac support several 11ac devices it did not advertise
VHT related information to cfg80211.
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The channel values used by firmware is handled using conversion functions
depending on the type of chip. These functions were already in place but
lacked proper support for 80MHz channel definitions. This patch adds the
support for that.
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the .start_ap callback cfg80211_get_chandef_type() was used to
provide debug log info. However, this causes a warning when the
chandef contains VHT channel with 80MHz bandwidth. Avoid the warning
by just printing the channel and bandwidth instead.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The DISASSOC command needs to be sent to firmware when a connection
loss is detected by firmware (e.g., beacon timeout). Otherwise the
next connect request fails due to a lingering LINK(down) event from
firmware. This patch resolves the issue by using brcmf_link_down()
handler, instead of the incomplete duplicated codes.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Daniel Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver serializes the nvram firmware file before sending it
to the device. This patch enhances this to assure serialized data
is properly formatted and provide warnings on syntax failures.
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
FWS is always queuing frames and using a worker for de-queueing,
this is not always efficient for all bus layer. For example SDIO
has an internal queue and worker making the queueing of FWS
unnecessary. Make it possible to bypass the worker if fws mode
is none using a bus interface configuration. For USB bus layer
this configuration is set true to have fws provide queueing
regardless the fws mode.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tracking and handling of 802.1x frames is done in two modules, it
is more logical and clear to move this to dhd_linux module.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In tx_finalize the hdrpull is performed. For the new protocol
msgbuf this is complex, because it does not use protocol headers
in front of payload anymore and therefor can not determine interface
index in the hdr pulll operation. Move out the hdrpull operation
from tx_finalize to make msgbuf implementation easier.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently firmware roaming support is not reported to cfg80211.
This patch reports the support of firmware based roaming when
it is enabled.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Daniel Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a BSS provides both 2.4GHz and 5GHz bands, in many cases it
makes sense to choose 5GHz. Typically a 5GHz channel is less crowded
and has less interference and therefore its performance will be
better than a crowded 2.4 GHz channel. This patch configures
'join_pref' to induce firmware to preferably select 5GHz BSS.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Daniel Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
and use it. This move need changes in both drivers.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds choice submenu "Supported bus types" as two simple bool
configs would allow user to compile b43 without any bus support
(prety useless).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Users of new (BCMA based) wireless chipsets may not want to enable SSB.
This is hopefully the last code patch for dropping SSB dependency.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The check of ezusb_firmware_download() return value (added by commit
488ec87803) is broken because
ezusb_firmware_download() returns 1 on success.
This causes the driver not to work with the following error:
orinoco_usb: probe of 3-3:1.0 failed with error -14
Check the return value only for negative values.
This fix should be applied to -stable kernels too.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Systems with multiple DFS channel detectors need to track
timestamp of previous pulse per instance to display the
correct pulse interval.
Since the interval value is used for debug printing only,
this is a non-functional modification.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Originally Helmut posted a v2 of the "ath9k: Allow platform override
without EEPROM override", but I had prematurely commited the original
as commit 552a515707. This commit restores the tree to what Helmut
intended with his v2 submission. -- JWL
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The msi module parameter offers an option to enable or disable MSI
interrupts mode, for debugging and workaround(in case) convenience.
Signed-off-by: Adam Lee <adam.lee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The msi module parameter offers an option to enable or disable MSI
interrupts mode. For now, some users report RTL8188EE works only with
MSI on their certain platforms, some others report it works only without
MSI, this parameter will help.
Signed-off-by: Adam Lee <adam.lee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes MSI support a module parameter, for debugging and workaround
convenience.
Signed-off-by: Adam Lee <adam.lee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_beacon_loss() is only to be called in managed mode,
but the firmware may send the sync timeout event at any time,
so do a check before calling.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Tested-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The join arguments are mixed up, passing beacon_interval instead of
channel and channel instead of beacon_interval. Fix them.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Tested-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix the WARN below by not calling ieee80211_nullfunc_get() in IBSS mode,
but setting up empty template the same way wl12xx driver does.
WARNING: CPU: 0 PID: 914 at net/mac80211/tx.c:2750 ieee80211_nullfunc_get+0xc0/0xd0 [mac80211]()
Modules linked in: wl1251_sdio wl1251 mac80211 cfg80211
...
[<c00439c0>] (warn_slowpath_null)
[<bf0bdfdc>] (ieee80211_nullfunc_get [mac80211])
[<bf134774>] (wl1251_op_bss_info_changed [wl1251])
[<bf099e14>] (ieee80211_bss_info_change_notify [mac80211])
...
Also perform join command regardless of bss_type as that seems to be
required for proper operation.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Tested-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit b90a1165a7.
That commit (or rather, hack) triggers a scary WARN in IBSS (ad-hoc) mode.
Steps to reproduce:
ifconfig wlan0 down
iwconfig wlan0 mode ad-hoc
ifconfig wlan0 up
------------[ cut here ]------------
WARNING: CPU: 0 PID: 905 at kernel/workqueue.c:1400 __queue_work+0x21c/0x2f4()
Modules linked in: wl1251_sdio wl1251 mac80211 cfg80211
CPU: 0 PID: 905 Comm: ifconfig Not tainted 3.15.0-rc2#233
[<c0015f38>] (unwind_backtrace) from [<c0012938>]
[<c0012938>] (show_stack) from [<c05d4034>]
[<c05d4034>] (dump_stack) from [<c0043984>]
[<c0043984>] (warn_slowpath_common) from [<c00439c0>]
[<c00439c0>] (warn_slowpath_null) from [<c005b6c8>]
[<c005b6c8>] (__queue_work) from [<c005b820>]
[<c005b820>] (queue_work_on) from [<bf134ac0>]
[<bf134ac0>] (wl1251_op_config [wl1251])
[<bf099a70>] (ieee80211_hw_config [mac80211])
...
This happens because ieee80211_connection_loss() is not expected to be
called in IBSS mode (mac80211 ends up queuing uninitialized work
in that case).
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Tested-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In some situations (see comment) it makes sense to enable both
chains (if available) to get better throughput by having chain
diversity available.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Prevent sched scan while not idle (including during association or in AP
mode) instead of while associated only.
This fixes my previous commit which was incomplete:
commit bd5e4744a6
Author: David Spinadel <david.spinadel@intel.com>
Date: Thu Apr 24 13:15:29 2014 +0300
iwlwifi: mvm: do no sched scan while associated
Currently the FW doesn't support sched scan while associated,
Prevent it.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
tail should be equal to the last valid index, so
decrease it by one.
This error causes in "a gap" in some cases (as well as
some possible out-of-bound write), finally resulting in
ucode assertion.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fix a bug in nvm_read_section function if size of the section
is a multiple of 2K:
- if the size of the section is *not* multiple of 2K,
then we will have: read(2K) - return 2K ... read(2K) - return 2K
read(2K) - return the rest (in bytes) and exit the while loop.
- else, if the size of the section is a multiple of 2K,
then we have: read(2K) - return 2K read(2K) - return 2K read(2K) -
return 2K read(2K) - return 0 and exit the while with an error.
We should not return an error in the latter case, because it
might well be that the section was completely read.
Also, we try now to read all the sections as this is needed
for new devices.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
setting SKIP_OVER_DTIM when skip_dtim_periods is 0
causes a ucode assert. set the flag only if needed.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When calling IWL_DEBUG_*() dev_dbg() is currently used, and this
could result in the log being ignored no matter the internal
loglevel, since dev_dbg() may get turned on or off based on the
dynamic debug mechanism.
Replace the dev_dbg() with dev_printk() since dynamic printing
is pointless as we use our own debug level mechanism and there
is just a single dev_dbg() call in the code.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
[rephrase commit message a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
CMD_SYNC is really 0 which is confusing:
if (cmd.flags & CMD_SYNC) is always false.
Fix this by simply removing its definition.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Timing mode identifier has same role and can take the place
of speed mode. This change removes all related speed mode.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Fix iovar 'bw_cap' set command failure introduced by
commit ff3b0fba6f25555ef59c55d138a467d0f81d82d7
Author: Arend van Spriel <arend@broadcom.com>
Date: Sat Mar 15 12:00:57 2014 +0100
brcmfmac: fallback to mimo_bw_cap for older firmwares
This resulted in disabling 20MHz operation in the firmware.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Daniel Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Conflicts:
drivers/net/ethernet/altera/altera_sgdma.c
net/netlink/af_netlink.c
net/sched/cls_api.c
net/sched/sch_api.c
The netlink conflict dealt with moving to netlink_capable() and
netlink_ns_capable() in the 'net' tree vs. supporting 'tc' operations
in non-init namespaces. These were simple transformations from
netlink_capable to netlink_ns_capable.
The Altera driver conflict was simply code removal overlapping some
void pointer cast cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
There's an extra newline that shouldn't be there - remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
If a (debug) message is missing a newline, cause build error
so we don't keep reintroducing this problem.
This also prevents using a non-constant argument as the format
string which is a good idea anyway (e.g. for security reasons.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
A binding object associates virtual MACs to a Phy.
Binding object can ask (and get) air time, thus
allowing several MACs to share the medium.
A binding object can be in either one of 3 states:
1) standalone - A single active MAC
2) Different Channel Mode (DCM) - There are 2 active
MACs or more (not necessarily just clients), but each
has its own channel.
3) Same Channel Mode (SCM) - There are 2 active
MACs or more (not necessarily just clients), that
share the same channel.
This patch introduces an additional condition for enabling uAPSD:
uAPSD should be disabled for a client in DCM.
The reason for that is a low latency issue in Miracast.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
If two clients are active while each one is alone on its channel,
and the applicable flags are set, power management should be enabled.
This condition is referred to as Different Channel Mode (DCM).
Up to now, in DCM power management was supported only on BSS.
This patch adds support for P2P power management in DCM as well.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Stop sched scan on bss_info_changed if !idle to avoid sched scan
during association.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add an option to notify mac80211 about sched scan complete from
iwl_mvm_stop_sched_scan(), to enable this notification when the
stop was called from within the driver.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
in family 8000: additional channel 14 added to the low
band list. now the number of channels in the low band
is 15.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Reviewed-by: Dor Shaish <dor.shaish@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Some races with the hardware can happen when we take
ownership of the device. Don't give up after the first try.
Cc: <stable@vger.kernel.org>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The 8000 family products need a file on the file system
which is used as NVM. This file is a must, if no filename
is supplied as module parameter, use a default filename.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Reviewed-by: Dor Shaish <dor.shaish@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This is not needed since the PCIe layer disables the
bottom halves before it calls the op_mode.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
All messages should have a trailing newline, add all the
missing ones. Also make all messages constants, replacing
the single one that pointlessly used a variable.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
CTS protection was not working properly because the HW needs
RTS flag to be asserted, and it need also RTS duration field to be
filled with CTS-to-self duration.
This patch makes the driver to do this.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CTS protection was not working properly because the HW still need
RTS flag to be asserted, and it need also RTS rate field to be
set with CTS-to-self rate and RTS duration field to be filled with
CTS-to-self duration.
This patch makes the driver to do this.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch make it possible to mac80211 to know whether a frame
has been received with short preamble.
It simply checks for the "splcp" flag in the RX status
descriptor, and eventually set RX_FLAG_SHORTPRE in mac80211
rx status structure.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch make it possible to mac80211 to know whether a frame
has been received with short preamble.
It simply checks for the "splcp" flag in the RX status
descriptor, and eventually set RX_FLAG_SHORTPRE in mac80211
rx status structure.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a new platform data flag "use_eeprom" that indicates that the eeprom
found on the card itself should be used instead of the one present in
the platform data.
This allows to override the MAC address of a PCI card while preserving
the eeprom data from the card itself.
The default behavior is preserved.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support to populate HT operatation IE in TDLS
setup confirm command. This is required for setting wider
bandwidths for TDLS operations.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds code to disable TDLS link upon reception of TDLS
teardown event from peer. Teardown event can happen either
because of TDLS teardown packet from peer or internal timeout
configured during TDLS setup. Event is propogated to cfg80211
so that userspace application can take appropriate action.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds configuration timeout for TDLS link. This is
configuered at the time of TDLS link configuration. If TDLS link
is inactive for more than timeout, FW will tear this link.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In case RFKILL is in KILL position, the NIC will issue an
interrupt straight away. This interrupt won't be sent
because it is masked in the hardware.
But if our interrupt service routine is called for another
reason (SHARED_IRQ), then we'll look at the interrupt cause
and service it. This can cause bad things if we are not
ready yet.
Explicitly clean the interrupt cause register to make sure
we won't service anything before we are ready to.
Cc: <stable@vger.kernel.org> [3.14]
Reported-and-tested-by: Alexander Monakov <amonakov@gmail.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
After fixes to the rs algorithm reenable MCS9.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Since the declaration of iwl_mvm_fw_error_rxf_dump and
iwl_mvm_fw_error_sram_dump is under
ifdef CONFIG_IWLWIFI_DEBUGFS, do the same for their
implementation.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Publish WIPHY_FLAG_HAS_CHANNEL_SWITCH if the fw supports
newly introduced IWL_UCODE_TLV_API_CSA_FLOW.
When CSA starts, save the switching vif inside mvm and during the CSA period
configure fw with a new beacon after each beacon transmission in order to
update the csa counters.
Also, handle correctly the CSA unbind-bind flow which is triggered by mac80211
when the actual channel switch happens.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Some ampdu actions change queues by direct target access.
Since the bus is disabled in d0i3, make sure to exit d0i3
before handling these actions.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When a firmware error occurs, capture the last 32 commands
(which are still in memory) in the error dump debugfs file.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Currently the FW doesn't support sched scan while associated,
Prevent it.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The SREV register in the WMAC register space does not contain the chip
revision, so it needs to be passed in from the kernel.
With an updated kernel, this fixes tx gain table selection.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With certain hardware combinations the poll interval is exceeded before
initialization completes.
Tested on a MacBookPro10,1 using a Sabrent USB-A11N USB adapter.
Signed-off-by: Andy Spencer <andy753421@ucla.edu>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will enable AP mode to change channel width dynamically
based on 20/40 intolerance report sent by associated client.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A similar patch fixed crashes seen on an ath9k system
when testing against a broken ath10k AP. This patch
is slightly less protective, but probably will do the
job and is less redundant.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This variable always tracks a constant value (256) so there's
no need to have it. Removing it simplifies code generation,
reducing the .text size (by about 240 bytes on x86-64.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The 'reset' argument is clearly a boolean, so use bool instead
of u8 with 0/1 values.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
If there's no LED on the system, it doesn't make a lot of sense
to include close to 4k of LED-related code (mostly in mac80211),
so instead of forcing LED support into the kernel, don't build
iwlwifi/mac80211 LED support if there's no LED class support.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: EliadX Peller <eliad@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The old code checks if hw_section_num is valid while the
right thing to do is to check if section[hw_section_num].data
is valid.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Reviewed-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
For family 8000 products, the driver should take the MAC
address from the mac_override section and only if this
section is empty it should take it from the HW section.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Read first the nvm sections from the OTP, then read the nvm
sections from the external file and override the OTP values
(if there were any values in the OTP).
Signed-off-by: Eran Harary <eran.harary@intel.com>
Reviewed-by: Dor Shaish <dor.shaish@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
A few devices aren't allowed to be powered up at driver
load time. Add "power_up_nic_in_init" flag to iwl_cfg
structure to customize the load flow according to the
device.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
OTP size changed in family 7000 and in family 8000.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
There's no need to use a variable just to return the result
of another function call at the end of a function, remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The expected throughput table used when estimating a new column
depends on the channel bandwidth. When switching from legacy to
siso or mimo the wrong expected throughput table was used as it
was chosen based on the the channel bandwidth in legacy which is
always 20Mhz. Instead it should be chosen based on the current sta
bandwidth which could be also 40Mhz or 80Mhz.
When enabling MCS9 this bug leads to a problem where the max
expected throughput of the siso or mimo column is 0 as MCS9 isn't
supported in 20Mhz. This in turns prevents switching to siso or mimo.
Fix this by using the sta bandwidth when deciding which table to choose.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
TPC is a power optimization which should only be attempted when
we're in the "stay in column" state after we've locked onto an optimal
rate.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Currently we were checking only if the driver power_scheme is set
to CAM. TPC shouldn't be enabled also when disabling powersave on the
interface (e.g. iw wlan0 set power_save off)
which may occur even if power_scheme wasn't set to CAM.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
rs_get_best_rate determines the optimal rate to try in a
new Tx column. Currently we were sometimes trying a too high
rate which would lead us to fail and avoid switching to the
new column despite it having a potential to be better.
Change the logic to try and find the first rate which would
exceed the current actual throughput or be more aggressive
if the success ratio is good.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Adding more options in the search cycle causes longer
search cycles with additional wondering off to non optimal Tx
configurations. Reduce the Tx configurations searched to
improve throughput in non optimal attenuations.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
My bad - I forgot to update this when sending the patch
upstream.
Fixes: 87d5e4155c ("iwlwifi: mvm: rs: reinit rs if no tx for a long time")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The commit below introduced a bug in the validity bits in
init. Due to that, all the Coex mechanism stopped sending
kills to the BT side. Fix that.
Fixes: b9fae2d54c ("iwlwifi: mvm: BT Coex add support for Co-running block")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fixes: a53268be0c ('rtlwifi: rtl8192cu: Fix too long disable of IRQs')
Cc: stable@vger.kernel.org
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Beginning with kernel 3.13, this driver fails on some systems. The problem
was bisected to:
Commit 1bf4bbb402
Author: Felix Fietkau <nbd@openwrt.org>
Title: mac80211: send control port protocol frames to the VO queue
There is noting wrong with the above commit. The regression occurs because
V0 queue on RTL8192SE cards uses priority 6, not the usual 7. The fix is to
modify the rtl8192se routine that sets the correct transmit queue.
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=74541
Reported-by: Alex Miller <almiller_1@yahoo.co.uk>
Tested-by: Alex Miller <almiller_1@yahoo.co.uk>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [3.13+]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adjust FIR filter co-efficients to improve EVM for 11b rates.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rfsat gainchange hysteresis of rf_gain stuck with large
interference present.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I was reading ath5k power setting code and
noticed typing error in ath5k_hw_txpower function.
Invalid value was written to AR5K_PHY_TXPOWER_RATE_MAX
register.
Signed-off-by: Nikolay Ledovskikh <nledovskikh@gmail.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Coverity CID 986698 reports leakage of struct wlcore_platdev_data in the
probe functions of both the SPI/SDIO interfaces. The structure passed to
platform_device_add_data() is dynamically allocated and only freed in the
error paths, however, platform_device_add_data() adds a copy of the platform
specific data to the device. Move the temporary struct that is kmemdup'ed
to the stack. This issue exists since afb43e6d (wlcore: remove if_ops from
platform_data).
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
94010fa0dd ("rtlwifi: add MSI interrupts
mode support") introduced MSI interrupts mode support, which seemed
safe enough with RTL8188EE and RTL8723BE as RealTek's testing results,
but some users reported their RTL8188EE modules could not connect to
any wireless network after the MSI mode was enabled by Ubuntu 14.04.
So, let's fallback to pin-based mode until rtlwifi's MSI support get
good compatibility.
BugLink: https://bugs.launchpad.net/bugs/1310512
Signed-off-by: Adam Lee <adam.lee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 2a54eb5e14
("rtlwifi: rtl8188ee: enable MSI interrupts mode").
94010fa0dd ("rtlwifi: add MSI interrupts
mode support") introduced MSI interrupts mode support, which seemed
safe enough with RTL8188EE and RTL8723BE as RealTek's testing results,
but some users reported their RTL8188EE modules could not connect to
any wireless network after the MSI mode was enabled by Ubuntu 14.04.
So, let's fallback to pin-based mode until rtlwifi's MSI support get
good compatibility.
BugLink: https://bugs.launchpad.net/bugs/1310512
Signed-off-by: Adam Lee <adam.lee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Setting it to true during init doesn't seem to be any workaround while
it can cause problems (not enabling radio due to belief it's enabled).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes dealing with pointers directly and allows tracking radio
state with radio_on variable.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are some corner cases where the driver could get stuck with a full
tid queue that is paused, leading to a software tx queue hang.
Since the tx queueing rework, pausing per-tid queues on aggregation
session setup is no longer necessary. The driver will assign sequence
numbers to buffered frames when a new session is established, in order
to get the correct starting sequence number.
mac80211 prevents new frames from entering the queue during setup.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the amount of noise fluctuates strongly, low immunity settings
can sometimes disrupt signal detection on AR913x chips. When that
happens, no OFDM/CCK errors are reported anymore, and ANI tunes the
radio to the lowest immunity settings.
Usually rx/tx fails as well in that case.
To fix this, keep noise immunity settings at or above ANI default level,
which will keep radio parameters at or above INI values.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 takes care of all the needed steps for hwsim, so indicate
support for this capability.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
brcmfmac has been broken on my cubietruck with a BCM43362:
brcmfmac: brcmf_chip_recognition: found AXI chip: BCM43362, rev=1
brcmfmac: brcmf_c_preinit_dcmds: Firmware version = wl0:
Apr 22 2013 14:50:00 version 5.90.195.89.6 FWID 01-b30a427d
since commit 53036261033: "brcmfmac: update core reset and disable routines".
The problem is that since this commit brcmf_chip_ai_resetcore no longer sets
BCMA_IOCTL itself before bringing the core out of reset, instead relying on
brcmf_chip_ai_coredisable to do so. But brcmf_chip_ai_coredisable is a nop
of the chip is already in reset. This patch modifies brcmf_chip_ai_coredisable
to always set BCMA_IOCTL even if the core is already in reset.
This fixes brcmfmac hanging in firmware loading on my board.
Cc: stable@vger.kernel.org # v3.14
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k: move sc_flags to ath_common" moved setting
ATH_OP_INVALID flag below ieee80211_register_hw. This is causing
the flag never being cleared randomly as the drv_start is called
prior to setting flag. Fix this by setting the flag prior to
register_hw.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit e050c76fcf.
I'm not sure what crack pipe I was using when I merged this...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Beacon data wasn't properly cleared during early
phase of recovery. This in turn caused firmware to
crash because the beacon data was submitted before
vdevs were fully re-configured. Ultimately the
device was considered wedged and nothing worked
until driver was reloaded.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If DMA mapping of next beacon failed ath10k leaked
the beacon.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If DMA mapping of next beacon failed it was
possible for next SWBA to access a pointer that
was already unmapped and freed. This could cause
memory corruption.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If for some reason mac80211 wouldn't stop
beaconing gracefully and just removed interface of
a running AP/IBSS interface it was possible to
leak pending beacon DMA mapping. It's very
unlikely but better safe than sorry.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It doesn't make much sense to even try suspending
the device when recovering. Recovering means the
device is unresponsive and waiting for suspend
procedure means taking a 3 second timeout waiting
for tx credits.
This speeds up firmware recovery significantly.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When warm resetting it's possible for device to
crash during initialization. Instead of waiting 3
seconds just return failure as soon as
FW_IND_EVENT_PENDING is set.
This speeds up device bootup and recovery in some
cases.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This just makes it easier to tell apart different
kinds of bringup failure.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is the first step to remove leftover code.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We've implemented table calculation, but forgot to enable writing it in
power setup function.
By the way document table layout.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Logic in specs and our code was wrong. Init and calibration values for
newer cards depend on radio revision, not PHY revision.
To make code clearer, change tables names to include "radio" or "phy".
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
They were extracted from MMIO dumps of 14e4:4353 and wl 6.30.223.141.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bit 0x200 has been noticed in the following log:
radio_read(0x02ca) -> 0x0000
radio_write(0x00ca) <- 0x0080
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
New Broadcom drivers don't upload it anymore. It was probably a copy & paste
mistake in early N-PHY rev 3+ days.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently AMSDU and AMPDU aggregation is enabled for TID 0 to
TID 5 streams. Lets enable it for remaining two streams also.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will help to aggregate more packets which yields better
throughput results for 11ac chipsets.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will help to aggregate more packets which yields better
throughput results.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Firmware dump feature is added for PCIe based chipsets.
Separate file will be created at /var/log/fw_dump_*
for each memory segment.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This option be useful to dump firmware memory for debugging
purpose. Actual code to dump firmware momory for SDIO and PCIe
chipsets will be added later.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After changing local per interface beacon setting restore original
global beaconing state.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When command timeout occurs due to a firmware/hardware bug,
there is no chance of next command being successful. We will
keep cmd_sent flag on so that next command won't be sent to
firmware.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IE's are parsed from beacon buffer and stored locally using
mwifiex_update_bss_desc_with_ie() function.
Sometimes the local pointers point to the data inside IE, but
while using them it is assumed that they are pointing to the IE
itself.
These issues are fixed in this patch.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
'add_remove_card_sem' semaphore already takes care of
synchronization for driver load and unload threads.
Hence there won't be a case when unload thread is waiting on
'wait_for_completion(fw_load)'.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This option allows driver to finish pending operations in
disconnect handler by not killing URBs after usb_deregister
call.
We will get rid of global pointer 'usb_card' by moving code
from cleanup_module() to disconnect(). This will help to match
with our handling for SDIO and PCIe interfaces.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
New skbs are allocated at the time of AMSDU aggregation. Setting
up in timestamps for such skbs was missing which would result
into wrong queue delays passed to FW. Fix this by setting
timestamp of skbs created for AMSDU aggregation.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Command nodes are increased from 20 to 50. Now we can always
scan 1 channel per scan command to avoid traffic delay/loss in
connected state. We will get rid of *CHANNEL_PER_SCAN_CMD macros
used due to command node constraints.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For PCIe, aggregate more AMSDU packets till PCIe TXBD is full.
For SDIO, aggregation was disabled for AMSDU packets because
AMSDU aggregated packet size is already 4K or 8K, SDIO Multiport
Aggregation feature didn't use to gain much previously.
Now with increased multiport aggregation buffer, we can enable
it for AMSDU packets.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently Tx and Rx buffer sizes are 8K and 16K respectively for
all chipsets. We will change them to 32K for SD8897 and 16K for
older chipsets. SD8897 chipset has more SDIO data ports than
older chipsets.
This patch will help to improve throughput numbers.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
WARNING: single byte memset is suspicious.
Swapped 2nd/3rd argument?
This code happens to work because rx_mcs is the first variable
in mcs structure. We should use 'mcs.rx_mcs' here anyway.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Maithili Hinge <maithili@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When using scatter-gather, more descriptor entries get used.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes, due to the race between Rx path and WMI_BA_STATUS_EVENTID WMI event,
few frames may be passed to the stack before reorder buffer allocated.
Then, after BACK establishment, it start getting frames with sequence number ahead of
SSN, and it get interpreted as missing frames. Then, BACK mechanism will wait
for missing frames; data traffic will be stopped. In case of interface configured
for DHCP, this data delay causes DHCP failure.
Relax checking for sequence number; use sequence of 1-st frame handled by the buffer
as SSN for this buffer.
This is work-around, real fix should be done when proper BACK mechanism implemented.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- add pcp_max_assoc_sta to the struct wmi_pcp_start_cmd
- enum for the scan ststus
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reshuffle prints to consolidate firmware/hardware information
report upon card init
Convert print for unhandled MISC ISR bits to "debug" - it is
normal situation and not an "error"
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use generic TSF timers to trigger powersave state changes based
information from the P2P NoA attribute.
Opportunistic Powersave is not handled, because the driver does not
support powersave at the moment.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Preparation for adding P2P powersave and multi-channel support.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use del_timer_sync to ensure that the timer is stopped on all CPUs before
the driver exits.
This change was suggested by Thomas Gleixner.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier i,t,ex;
@@
struct t i = { .remove = ex, };
@@
identifier r.ex;
@@
ex(...) {
<...
- del_timer
+ del_timer_sync
(...)
...>
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
HW should never attempt to perform DMA for unused queues.
For rtl8187se this is ensured by setting a dedicated register at
init time, before enabling TX.
In rtl8180/5 the register is only written at the first TX (because
in rtl8180/5 it serves also to kick DMA for used queues).
This should be enough, but it's worth to add a register write at
init time, before enabling TX.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Parentheses are missing around the macro argument, causing the
macro possibly not to work passing certain expressions as
arguments.
This should not cause any issues with current code, however it's
worth to add them, as a good practice, and to eventually avoid
future bugs.
Suggested-by: Dave Kilroy <kilroyd@googlemail.com>
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When preparing the bitfield to write to HW register, the high-priority
queue error interrupt bit is set two times, and the beacon queue
TX-OK interrupt is not enabled.
Currently this have no functional impact because the high-priority
queue is not used at all, and the beacon queue is not used yet.
This patch removes high-priority queue bits and it adds the
beacon queue missing bit.
It removes also the management queue bits because it is not used.
This was found by static code analyzer.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rtl8180 driver can handle also rtl8185 and rtl8187SE cards,
however in userspace tools (network manager) it still appares
as "rtl8180".
This might lead the user to think the wrong driver is in use.
This patch changes module name to "rtl818x_pci" that should be
more explanatory.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> [ original patch ]
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement a recv budget so that in cases of high traffic we still allow other
taskets to get processed.
Without this, we can encounter a host of issues during high wireless traffic
reception depending on system load including rcu stall's detected (ARM),
soft lockups, failure to service critical tasks such as watchdog resets,
and triggering of the tx stuck tasklet.
The same thing was proposed previously by Ben:
http://www.spinics.net/lists/linux-wireless/msg112891.html
The only difference here is that I make sure only processed packets are counted
in the budget by checking at the end of the rx loop.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a flush is requested, make sure to clear the descriptor once we've
processed it.
This resolves a hang that will occur if all RX descriptors are full when a
flush is requested.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
static code analysis from cppcheck reports:
[drivers/net/wireless/rtlwifi/rtl8188ee/trx.c:322]:
(error) Uninitialized variable: packet_beacon
packet_beacon is not initialized and hence packet_beacon
contains garbage from the stack, so set it to false.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Cc: Stable <stable@vger.kernel.org> [3.10+]
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When disable beaconing we clear register with beacon and newer set it
back, what make we stop send beacons infinitely.
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes when command timeout occurs due to a firmware or
hardware bug, there may be some synchronous commands in command
queue. These commands are never downloaded to firmware causing
hung task warnings. This patch replaces wait_event_interruptible
call with wait_event_interruptible_timeout to fix the issue.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During extended scan, SCAN report event is always followed by
command response. Sometimes It is observed that command response
is processed before SCAN report which leads to a crash, because
current command node is cleared while handling the response.
This patch makes sure that driver's main thread gives priority
to events over command responses.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Maithili Hinge <maithili@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some fields are missing from the event mailbox
struct definitions, which cause issues when
trying to handle some events.
Add the missing fields in order to align the
struct size (without adding actual support
for the new fields).
Reported-and-tested-by: Imre Kaloz <kaloz@openwrt.org>
Cc: stable@vger.kernel.org # 3.14+
Fixes: 028e724 ("wl18xx: move to new firmware (wl18xx-fw-3.bin)")
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix a potential memory leak in the error path of function
rsi_send_auto_rate_request(). In case memory allocation for array
'selected_rates' fails, the error path exits and leaves the previously
allocated skb in place. Detected by Coverity: CID 1195575.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This array is used in debug string to display cw1200_link_status
defined in drivers/net/wireless/cw1200/cw1200.h.
Add missing strings for CW1200_LINK_RESET and CW1200_LINK_RESET_REMAP.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes the firmware sends a dummy packet event while we are in PLT
mode. This doesn't make sense, it's a firmware bug. Fix this by
ignoring dummy packet events when we're PLT mode.
Reported-by: Yegor Yefremov <yegorslists@googlemail.com>
Reported-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix a potential memory leak in function rsi_set_channel() that is used to
program channel changes. The channel check block for the frequency bands
directly exits the function in case of an error, thus leaving an already
allocated skb unreferenced. Move the checks above allocating the skb.
Detected by Coverity: CID 1195576.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/rsi/rsi_91x_core.c: In function ‘rsi_core_determine_hal_queue’:
drivers/net/wireless/rsi/rsi_91x_core.c:91: warning: ‘ii’ may be used uninitialized in this function
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
7000 device series have a fix for this hardware feature.
Stop disabling it, and get an improvement in Tx throughput.
This feature allows the scheduler to fetch more frames on
the fly while an A-MPDU is being built - which means that
we can get larger A-MPDU. This, of course, give an
improvement in the Tx throughput.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The driver can enable uAPSD and specify some of its related parameters.
This patch organizes this logic in a separate function.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
bail out from the suspend/resume callbacks if
d0i3 is used.
declare support for ANY wowlan trigger (i.e.
normal operation).
On resume, we shouldn't execute the d0i3 exit
flow (which might disconnect stations, etc.)
until mac80211 was resumed.
Add new flags to indicate we are in suspend,
and call the pending exit work on resume.
Since the resume flow can take some time, add
a new EXIT_WORK reference type to prevent going
back to d0i3 at this stage.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This patch enables Energy Based Scan (EBS) - intended to detect energy
on 5 GHz band channels. Passive scan on this band takes up to 2.64 sec
assuming 110mSec per-channel * 24 channels. EBS is designed to detect
energy on channels with intensive Wifi activity as well as those where
only beacons are transmitted. EBS completes sampling all channels within
shortest beacon frame transmission time. Total EBS duration is about 100
msec (typical beacon interval).
Detecting Wifi activity on 5 GHz band channels can significantly reduce
scan duration thus saving time and power. EBS failure reported by FW
disables EBS for current connection. It is re-enabled upon new
connection attempt on any WLAN interface.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Calling iwl_send_bt_init_conf for INIT firmware is not a
problem, and calling iwl_send_bt_prio_tbl from
iwl_send_bt_init_conf allows us to prepare for new API.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The BT Coex API underwent a minor backward compatible API
change.
We now need to set an invalid value in the override fields.
While at it, add kerneldoc comments on the fields in the
command.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This is really not needed. This is a remainder from a C99
initialiser.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
All the supported firmwares have this flag set.
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
All the supported firmwares have this flag set.
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
All the supported firmwares have this flag set.
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Arend van Spriel