In the wake tx queue path, we are not checking if the frame to be sent
takes management path or not. For eg. QOS null func frame coming here will
take the management path. Since we are not incrementing the descriptor
counter (num_pending_mgmt_tx) w.r.t tx management, on tx completion it is
possible to see negative values.
When the above counter reaches a negative value, we will not be sending a
probe response out.
if (is_presp &&
ar->hw_params.max_probe_resp_desc_thres < htt->num_pending_mgmt_tx)
For IPQ4019, max_probe_resp_desc_thres (u32) is 24 is compared against
num_pending_mgmt_tx (int) and the above condtions comes true if the counter
is negative and we drop the probe response.
To avoid this, check on the wake tx queue path as well for the tx path of
the frame and increment the appropriate counters
Fixes: cac085524c "ath10k: move mgmt descriptor limit handle under mgmt_tx"
Signed-off-by: Ashok Raj Nagarajan <arnagara@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
txqs_lock is interfering with wake_tx_queue submitting more frames.
so queues don't get filled in and don't keep firmware/hardware busy
enough. This change helps to reduce the txqs_lock contention and
wake_tx_queue() blockage to being possible in txrx_unref().
To reduce turn around time of wake_tx_queue ops and to maintain fairness
among all txqs, the callback is updated to push first txq alone from
pending list for every wake_tx_queue call. Remaining txqs will be
processed later upon tx completion.
Below improvements are observed in push-only mode and validated on
IPQ4019 platform. With this change, in AP mode ~10Mbps increase is
observed in downlink (AP -> STA) traffic and approx. 5-10% of CPU
usage is reduced.
Major improvement is observed in 1-hop Mesh mode topology in 11ACVHT80.
Compared to Infra mode, CPU overhead is higher in Mesh mode due to path
lookup and no fast-xmit support. So reducing spin lock contention is
helping in Mesh.
TOT +change
-------- --------
TCP DL 545 Mbps 595 Mbps
TCP UL 555 Mbps 585 Mbps
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
'WMI_10_4_WDS_PEER_EVENTID' is not yet handled/implemented for WDS mode,
as of now suppress the warning message "Unknown eventid: 36903"
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Recent commit 46f6b06050 ("mac80211: Encrypt "Group addressed privacy" action
frames") encrypts group privacy action frames. But qca99x0 family chipset
delivers broadcast/multicast management frames as encrypted and it should be
decrypted by mac80211. Setting RX_FLAG_DECRYPTED stats for those frames is
breaking mesh connection establishment.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
With the %pK format specifier we hide the kernel addresses
with the help of kptr_restrict sysctl.
In this patch, %p is changed to %pK in the driver code.
The sysctl is documented in Documentation/sysctl/kernel.txt.
Signed-off-by: Maharaja Kennadyrajan <c_mkenna@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WMI_SERVICE_PERIODIC_CHAN_STAT_SUPPORT service has missed in
the commit 7e247a9e88 ("ath10k: add dynamic tx mode switch
config support for qca4019"). This patch adds the service to
avoid mismatch between host and target.
Fixes: 7e247a9e88 ("ath10k: add dynamic tx mode switch config support for qca4019")
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently the FW version is taken from the sw_version field
of the FW ready event. This version is based on internal
version control revision and it is difficult to map to actual
FW version.
Fix this by using the actual FW version stored in the FW file
header record.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When driver is loaded, extract a capabilities record
from the FW file. This record contains bits indicating
which optional features are supported by this FW.
The driver can use this information to determine
which functionality to support and/or expose to user
space.
The extraction is done before wiphy structure is
registered, because the capabilities can affect
information published by the this structure.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Align to latest version of the auto generated wmi file
describing the interface with FW.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently the places that check wil->scan_request and
call cfg80211_scan_done are not consistently protected,
so there is a risk that cfg80211_scan_done will be called
with NULL scan_request, causing a kernel crash.
Fix this by using p2p_wdev_mutex in few other places
that access scan_request. This makes sense since
scan_request may point to p2p_wdev, and it is not worth
the extra complexity of adding a new mutex.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
HW Rx filters and masks are not configured
properly by firmware during boot sequences. The
MAC_PCU_ADDR1 is set to 0s instead of 1s which
allows the HW to ACK any frame that passes through
MAC_PCU_RX_FILTER. The MAC_PCU_RX_FILTER itself
is misconfigured on boot as well.
The combination of these bugs ended up with the
following manifestations:
- "no channel configured; ignoring frame(s)!"
warnings in the driver
- spurious ACKs (transmission) on the air during
firmware bootup sequences
The former was a long standing and known bug
originally though mostly harmless.
However Marek recently discovered that this
problem also involves ACKing *all* frames the HW
receives (including beacons ;). Such frames
are delivered to host and generate the former
warning as well.
This could be a problem with regulatory compliance
in some rare cases (e.g. Taiwan which forbids
transmissions on channel 36 which is the default
bootup channel on 5Ghz band cards). The good news
is that it'd require someone else to violate
regulatory first to coerce our device to generate
and transmit an ACK.
The problem could be reproduced in a rather busy
environment that has a lot of APs. The likelihood
could be increased by injecting an msleep() of
5000 or longer immediately after
ath10k_htt_setup() in ath10k_core_start().
The reason why the former warnings were only
showing up seldom is because the device was either
quickly reset again (i.e. during firmware probing)
or wmi vdev was created (which fixes hw and fw
states).
It is technically possible for host driver to
override adequate hw registers however this can't
work reliably because the bug root cause lies in
incorrect firmware state on boot (internal
structure used to program MAC_PCU_ADDR1 is not
properly initialized) and only vdev create/delete
events can fix it. This is why the patch takes
dummy vdev approach.
This could be fixed in firmware as well but having
this fixed in driver is more robust, most notably
when thinking of users of older firmware such as
999.999.0.636.
Reported-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This allows placing command barriers for explicit
serializing and synchronizing state.
Useful for future driver development.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Will be useful for implementing command barriers.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Will be useful for implementing command barriers.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch adds testmode support for 10.4 based chipsets
and added code swap support for UTF binary.
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently testmode events for 10.x firmware are processed from
10.1 wmi event processing. This patch is used to handle testmode
events in 10.2 and 10.4 based firmware.
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Preparation to make use of firmware_swap_code_seg_info for UTF binary.
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Support for QCA9887 is no longer experimental and if there are any issues
we need to address them
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
A station pointer can be passed to the driver on tx, before it has been
marked as associated. Since ath9k_sta_state was initializing the entry
too late, it resulted in some spurious crashes.
Fixes: df3c6eb34d ("ath9k: Use sta_state() callback")
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently wiphy structure is initialized and registered
in wil_if_alloc, before some information is available such
as MAC address and capabilities. As a result there is a
small chance user space will get incorrect information
from calls such as NL80211_CMD_GET_WIPHY.
Fix this by seperating the registration and moving it
to wil_if_add which is executed later, after all
relevant information is known.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
txdata->enabled is used in order to determine if the TX vring
is valid. As the data transmit is handled in a different context,
in case txdata->enabled is set before vring->hwtail is updated,
an old or corrupted vring->hwtail can be used.
Protect setting of txdata->enabled and vring->hwtail to prevent a
case where TX vring start handling TX packets before setting
vring->hwtail.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Stations disconnection is executed as part of wil_reset so no
need to do it in wil_down.
Removal of the disconnect operation will also preserve the lock
of wil->mutex during the whole reset flow and prevent handling of
connect event while resetting.
Set wil_status_resetting in earlier stage in the flow to prevent
double resetting call in case communication with FW fails while
bringing the interface down.
Signed-off-by: Lazar Alexei <qca_ailizaro@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
fix stop p2p device handling to identify between search
and listen and update the upper layers with the appropriate
notification.
The stop of p2p radio operations also needs to be performed
in __wil_down.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Change the logging category of HALP functions from
MISC to IRQ, since the HALP mechanism is closely
related to interrupts. Both HALP and IRQ create
a heavy load of logging messages when enabled,
so their logging is typically disabled during normal debug
scenarios. Having them in the same logging category
will make it easier to disable logging for both in one go.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
According to the spec the PN should be calculated per TID.
In the current implementation, the PN and key_set were set
only for TID 0, therefore only traffic for TID 0 was supported.
In order to support all TIDs, the key_set and PN should be set
for all the TIDs.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In case HALP vote times out, we need to mask the HALP IRQ, as done
in case the interrupt is received, as this interrupt should be
set until completion of the low latency operation.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Align to latest version of the auto generated wmi file
describing the interface with FW.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
just to comply with current ath9k_hw_nvram_read to return value, hence
behaving reacting accordingly.
Signed-off-by: Eduardo Abinader <eduardo.abinader@riverbed.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fixes smatch warning:
ath9k_vif_iter_set_beacon() warn if statement not indented
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Minor overlapping changes for both merge conflicts.
Resolution work done by Stephen Rothwell was used
as a reference.
Signed-off-by: David S. Miller <davem@davemloft.net>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The use of config_enabled() against config options is ambiguous. In
practical terms, config_enabled() is equivalent to IS_BUILTIN(), but the
author might have used it for the meaning of IS_ENABLED(). Using
IS_ENABLED(), IS_BUILTIN(), IS_MODULE() etc. makes the intention
clearer.
This commit replaces config_enabled() with IS_ENABLED() where possible.
This commit is only touching bool config options.
I noticed two cases where config_enabled() is used against a tristate
option:
- config_enabled(CONFIG_HWMON)
[ drivers/net/wireless/ath/ath10k/thermal.c ]
- config_enabled(CONFIG_BACKLIGHT_CLASS_DEVICE)
[ drivers/gpu/drm/gma500/opregion.c ]
I did not touch them because they should be converted to IS_BUILTIN()
in order to keep the logic, but I was not sure it was the authors'
intention.
Link: http://lkml.kernel.org/r/1465215656-20569-1-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Stas Sergeev <stsp@list.ru>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Joshua Kinard <kumba@gentoo.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: "Dmitry V. Levin" <ldv@altlinux.org>
Cc: yu-cheng yu <yu-cheng.yu@intel.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Will Drewry <wad@chromium.org>
Cc: Nikolay Martynov <mar.kolya@gmail.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Rafal Milecki <zajec5@gmail.com>
Cc: James Cowgill <James.Cowgill@imgtec.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Adam Buchbinder <adam.buchbinder@gmail.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Mikko Rapeli <mikko.rapeli@iki.fi>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Cc: "Luis R. Rodriguez" <mcgrof@do-not-panic.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Roland McGrath <roland@hack.frob.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Tony Wu <tung7970@gmail.com>
Cc: Huaitong Han <huaitong.han@intel.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Juergen Gross <jgross@suse.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andrea Gelmini <andrea.gelmini@gelma.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Rabin Vincent <rabin@rab.in>
Cc: "Maciej W. Rozycki" <macro@imgtec.com>
Cc: David Daney <david.daney@cavium.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reduce indentation, use a variable to save a few pointer dereferences
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
AR_PHY_65NM_CH0_THERM and AR_CH0_THERM were supposed to refer to the
same register, however they had different SREV checks.
Remove the duplicate and use the checks. Since there were other SREV
checks present in the only place that uses this, this will probaby not
affect runtime behavior.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The register layout of AR_PHY_SPECTRAL_SCAN has changed, only AR9280
uses the old layout
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There were two paths in the code for "external" eeprom sources. The code
in eeprom.c only handled the cases where the eeprom data was loaded via
request_firmware. ahb.c and pci.c on the other hand had some duplicate
code which was only used when the eeprom data was passed via
ath9k_platform_data.
With this change all eeprom data handling is now unified in eeprom.c.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When an NL80211_DISCONNECT is sent to cfg80211, the driver's cfg80211
disconnect function sets the sme_state to SME_DISCONNECTED before receiving
a WMI_DISCONNECT_EVENT from the firmware. This caused cfg80211 to not know
that the connection is disconnected because the driver fails to notify
cfg80211 upon receiving WMI_DISCONNECT_EVENT from the firmware believing
it is already disconnected.
Signed-off-by: Dan Kephart <dan.kephart@lairdtech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When disabling tethering after having enabled it, the ath6kl driver does
not set the IFF_LOWER_UP flag to 0 (carrier off) on the wlan interface.
The upper layers (eg. connman) are not notified of the tethering mode
status change. So, tethering can not be activated anymore.
This patch adds a netif_carrier_off() call when stopping AP mode to fix
the problem.
Signed-off-by: Pierre Le Magourou <plemagourou@aldebaran.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
One minute after a successful connection, the kernel checks if the
frequency and the channel width are well configured for the country we
are in. (regulatory domain)
ath6kl driver was setting the NL80211_CHAN_HT20 channel without checking
for the HT capabilities. (we should have NL80211_CHAN_NO_HT in our
case because the firmware did not support HT)
This patch adds a check on ht_cap.ht_supported in order to create the
channel corresponding to the firmware capabilities.
Signed-off-by: Pierre Le Magourou <plemagourou@aldebaran.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When enabling WLAN tethering, a new AP is visible and a STA could
connect to it. When the STA tries to authenticate to the newly created
AP, the WPA authentication mechanism is stuck in the 1/4 msg of 4-Way
Handshake.
In ath6kl_rx(), the ath6kl_find_sta() function is looking for the
h_source field of the Ethernet frame header received by the STA. The
datap pointer that points to the Ethernet frame header is incorrect,
and was pointing at the wrong offset in the buffer.
This commit adds a pad_before_data_start offset to set the datap pointer
to the Ethernet frame header. datap->h_source parameter is now really
pointing to the source ethernet address and the authentication process
can continue.
Signed-off-by: Pierre Le Magourou <plemagourou@aldebaran.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Ideally wake_tx_queue should be used regardless as
it is a requirement for reducing bufferbloat and
implementing airtime fairness in the future.
However some setups (typically low-end platforms
hosting QCA988X) suffer performance regressions
with the current wake_tx_queue implementation.
Therefore disable it unless it is really
beneficial with current codebase (which is when
firmware supports smart pull-push tx scheduling).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
As hw cycle counters in QCA4019 wraparound independantly in QCA4019
it is possible cycle counter and rx clear counter would wraparound
at the same time. Current logic assumes only one of the counters
would wraparound at anytime. Fix this by moving 'else' part to
another 'if'.
Fixes: 8e100354a9 ("ath10k: fix cycle counter wraparound handling for QCA4019")
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Sometimes the firmware sends a HAL_DEL_BA_IND, the prima driver silently
ignore this message so let's do the same to silence the error message.
Cc: Nicolas Dechesne <nicolas.dechesne@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch fixes some issues with interface reconfiguration. It could
for example happen that an AP interface in beacon slot 0 was removed
leaving an IBSS station in one of the other slots. When this happens
the driver never sends out the beacon as it only tries to send a beacon
from slot 0.
Appart from that the tracking of required changes to the beacon config is
relatively complicated and prone to errors.
The approach taken here is to solve reconfiguration issues is to
reconfigure the beacons when any interface changes. This means that
the complexity of deciding whether an interface change may modify the
beacon configuration is gone. It also means that the beacon config will
be reliably updated when an interface is removed.
The issue that a single non-AP interface might not be in beacon
slot 0 and wouldn't be send out is solved by moving it into the
first slot. The TSF value in hardware is adjusted accordingly so
that the timestamp of the beacons stay consistent.
Signed-off-by: Benjamin Berg <benjamin.berg@open-mesh.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The removed ATH9K_SLOT_TIME_X constants simply map the value in microseconds
to the same integer. These constants were not used consistently, so fix the
inconsistency issue by replacing all occurances with the integer equivalent.
Signed-off-by: Benjamin Berg <benjamin.berg@open-mesh.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The ath9k driver modifies the TSF for VIFs for the purpose of sending
beacons in a staggered fashion. This patch exposes this VIF specific
adjustment of the TSF value to mac80211. Without the change the TSF
routines handle the hardware TSF value instead of the actual TSF value as
seen on the air.
Signed-off-by: Benjamin Berg <benjamin.berg@open-mesh.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
These changes make ath9k_hw_reset more consistent with other places that
handle the TSF value by using the same helper routine.
A slight improvement is to not assume that a fixed time of 1.5ms has
passed for the initval writes when compared to the first write attempt.
Instead the TSF value is re-calculated which will yield a higher accuracy
of the restored TSF timer.
Signed-off-by: Benjamin Berg <benjamin.berg@open-mesh.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The ath9k TSF handling routines need to be aware of the channel context that
is being modified. With this change the TSF related values that are stored
in each channel context will be correctly tracked and the harware will only
be updated if the modified context is currently the active one.
Without this change the TSF modifications done using these routines would
for example be lost during a hardware reset as done by ath_complete_reset.
Signed-off-by: Benjamin Berg <benjamin.berg@open-mesh.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Beacons were not send out at (timestamp % beacon_time == 0) for interfaces
other than the primary one. To send out beacons with the correct timestamp
according to 10.1.3.2 of the 802.11 standard the tsf_adjustment has to be
set to the negative time difference instead of positive. This way the
later beacons get corrected to have a lower (and similar) timestamp with
regard to the beacon from slot 0.
I am not aware about any issues that have been caused by this.
Signed-off-by: Benjamin Berg <benjamin.berg@open-mesh.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
No functional changes, this simply makes the code easier to understand
because all initialization based on ath9k_platform_data is now within
one function.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath9k_hw_init_macaddr unconditionally returns 0 in all cases, making the
return value unnecessary.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently setting the MAC address via ath9k_platform_data works only due
to the order in which init.c sets common->macaddr, which is done after
ath9k_hw_init_macaddr was executed. It would be better if the latter
was independent of the order in which it's being called.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
No functional changes - this only removes a variable which is set but
never read.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some devices running OpenWrt need this and it makes sense to add this
to ath9k_platform_data as the next patches will add a devicetree
(boolean) property for it as well.
Suggested-by: Vittorio Gambaletta <openwrt@vittgam.net>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix up the wcn36xx_smd_update_scan_params() to work with non-ancient
versions of the firmware and support actually specifying the list of
channels.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The CCU block in WCNSS is configured for appropriate routing of
interrupts from the DXE to the application cpu, this is not dependant on
the iris version (wcn3660 vs wcn3680), but rather if the SoC has a riva
or pronto built in.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Split the wcnss mmio space into explicit regions for ccu and dxe and
acquire these from the node referenced by the qcom,mmio phandle.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In preparation for handling incoming messages from IRQ context, change
the indication list lock to a spinlock
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Merge the two allocation instead of separately allocating room for the
indication payload.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Print an ath10k error message rather a call trace when HTT op version is
not found from firmware META data (IE). This should be sufficient to figure
out what went wrong.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA9888 shares the same configuration with QCA99X0
with NSS=2.
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
rtc_state_cold_reset_mask is unused in ath10k_hw_regs.
instead fixed delays are used.
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If WMI and/or firmware has issues removing the peer object,
then we still need to clean up the peer object in the driver.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Not sure this can happen, but seems like a reasonable sanity
check.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
just to comply to coding style.
Signed-off-by: Eduardo Abinader <eduardo.abinader@riverbed.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It is expected that all pktlog events for 10.4 firmware based solutions
should come through CE8 where as in case of 10.2 firmware based solutions,
it should come through one of the HTT events (HTT_T2H_MSG_TYPE_PKTLOG).
But from experiments with 10.4 based solutions, it is observed that pktlog
event for ATH_PKTLOG_TYPE_TX_MSDU_ID is coming through HTT pktlog event.
Currently, we always parse with 10.2 pktlog header which will lead to
pktlog decoding issues (payload length mismatch exceptions)
For trace points, it is required to provide only the payload size. So
fixing this by simplifying the payload size calculation without the use of
ath10k pktlog headers.
While there, remove the unused ath10k pktlog headers.
Signed-off-by: Ashok Raj Nagarajan <arnagara@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
<linux/semaphore.h> is not used anymore, so just remove the include.
Signed-off-by: Chaehyun Lim <chaehyun.lim@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
While debugging OS crashes due to firmware crashes, I enabled
kasan, and it noticed that peer objects were being used-after-freed.
Looks like there are two places we could be leaving stale references
in the peer-map, so clean that up.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Otherwise, the txrx-compl-task may access some bad memory?
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
cfg80211/nl80211 interface changes for per STA total rx-duration and
very basic 'ath10k_sta_statistics' mac80211 callback is implemented
to extend support for per station statistics from the driver.
Also provision in 'iw dev wlan#N station dump' to parse rx-duration
is supported. So its safer to remove the debugfs entry for per STA
rx-duration
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Enable support for 'drv_sta_statistics' callback.
Export rx_duration support if available to cfg80211/nl80211
This can also act as a placeholder for any new per STA stats support
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
10.4 'extended peer stats' will be not be appended with normal peer stats
data and they shall be coming in separate chunks. Fix this by maintaining
a separate linked list 'extender peer stats' for 10.4 and update
rx_duration for per station statistics. Also parse through beacon filter
(if enabled), to make sure we parse the extended peer stats properly.
This issue was exposed when more than one client is connected and
extended peer stats for 10.4 is enabled
The order for the stats is as below
S - standard peer stats, E- extended peer stats, B - beacon filter stats
{S1, S2, S3..} -> {B1, B2, B3..}(if available) -> {E1, E2, E3..}
Fixes: f9575793d4 ("ath10k: enable parsing per station rx duration for 10.4")
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add the following to support beacon report radio measurement
with the measurement mode field set to passive or active:
1. Propagate the required scan duration to the device
2. Report the scan start time (in terms of TSF)
3. Report each BSS's detection time (also in terms of TSF)
TSF times refer to the BSS that the interface that requested the
scan is connected to.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
[changed ath9k/10k, at76c59x-usb, iwlegacy, wl1251 and wlcore to match
the new API]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Beacon report radio measurement requires reporting observed BSSs
on the channels specified in the beacon request. If the measurement
mode is set to passive or active, it requires actually performing a
scan (passive or active, accordingly), and reporting the time that
the scan was started and the time each beacon/probe was received
(both in terms of TSF of the BSS of the requesting AP). If the
request mode is table, this information is optional.
In addition, the radio measurement request specifies the channel
dwell time for the measurement.
In order to use scan for beacon report when the mode is active or
passive, add a parameter to scan request that specifies the
channel dwell time, and add scan start time and beacon received time
to scan results information.
Supporting beacon report is required for Multi Band Operation (MBO).
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The function ar9003_hw_apply_minccapwr_thresh takes as second parameter not
a pointer to the channel but a boolean value describing whether the channel
is 2.4GHz or not. This broke (according to the origin commit) the ETSI
regulatory compliance on 5GHz channels.
Fixes: 3533bf6b15 ("ath9k: Fix regulatory compliance")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Cc: Simon Wunderlich <sw@simonwunderlich.de>
Cc: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Just setting the proper return for reading beyond the eeprom data.
Signed-off-by: Eduardo Abinader <eduardo.abinader@riverbed.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Found this obvious typo while going through the spectral
code design in ath10k
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Disable TX_STBC for both HT and VHT if the devices tx chainmask is '1'
TX_STBC is required only for devices with tx_chainmask > 1. This fixes
a ping failure for QCA9887 (1x1) in HT/VHT mode
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Enable beacon loss detection support for 10.4 by handling
roam event. With this change QCA99X0 station is able to
detect beacon loss when the AP is powered off
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Smatch warns about a number of cases in ath10k where a pointer is
null-checked after it has already been dereferenced, in code involving
ath10k private virtual interface pointers.
Fix these by making the dereference happen later.
Addresses the following smatch warnings:
drivers/net/wireless/ath/ath10k/mac.c:3651 ath10k_mac_txq_init() warn: variable dereferenced before check 'txq' (see line 3649)
drivers/net/wireless/ath/ath10k/mac.c:3664 ath10k_mac_txq_unref() warn: variable dereferenced before check 'txq' (see line 3659)
drivers/net/wireless/ath/ath10k/htt_tx.c:70 __ath10k_htt_tx_txq_recalc() warn: variable dereferenced before check 'txq->sta' (see line 52)
drivers/net/wireless/ath/ath10k/htt_tx.c:740 ath10k_htt_tx_get_vdev_id() warn: variable dereferenced before check 'cb->vif' (see line 736)
drivers/net/wireless/ath/ath10k/txrx.c:86 ath10k_txrx_tx_unref() warn: variable dereferenced before check 'txq' (see line 84)
drivers/net/wireless/ath/ath10k/wmi.c:1837 ath10k_wmi_op_gen_mgmt_tx() warn: variable dereferenced before check 'cb->vif' (see line 1825)
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The below warning message seems to hit occasionally with the following
combination (IPQ4019 + ACS scan) where we receive packets as a self peer
when hostapd does ACS when we bring up AP mode . ath10k has the below
fall back mechanism to fetch current operating channel in rx (it will
check for the next channel tracking variable if the current one is NULL)
[scan channel] --> [rx channel] --> [peer channel] -->
[vdev channel] --> [any vdev channel] --> [target oper channel]
'scan channel' and 'target operating channel' are directly fetched from
firmware events. All the others should be updated by mac80211.
During ACS scan we wouldn't have a valid channel context
assigned from mac80211 ('ar->rx_channel'), and also relying on
('ar->scan_channel') is not helpful (it becomes NULL when it goes to
BSS channel and also when the scan event is completed). In short we
cannot always rely on these two channel tracking variables.
'Target Operating Channel' (ar->tgt_oper_chan) seems to keep track of
the current operating even while we are doing ACS scan and etc. Hence
remove this un-necessary warning message and continue with
target_operating channel. At the worst case scenario when the target
operating channel is invalid (NULL) we already have an ath10k warning
message to notify we really don't have a proper channel configured in
rx to update the rx status("no channel configured; ignoring frame(s)!")
WARNING: CPU: 0 PID: 0 at ath/ath10k/htt_rx.c:803
[<c0318838>] (warn_slowpath_null) from [<bf4a0104>]
(ath10k_htt_rx_h_channel+0xe0/0x1b8 [ath10k_core])
[<bf4a0104>] (ath10k_htt_rx_h_channel [ath10k_core]) from
[<bf4a025c>] (ath10k_htt_rx_h_ppdu+0x80/0x288 [ath10k_core])
[<bf4a025c>] (ath10k_htt_rx_h_ppdu [ath10k_core]) from
[<bf4a1a9c>] (ath10k_htt_txrx_compl_task+0x724/0x9d4 [ath10k_core])
[<bf4a1a9c>] (ath10k_htt_txrx_compl_task [ath10k_core])
Fixes:3b0499e9ce42 ("ath10k: reduce warning messages during rx without proper channel context")
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Usually when the firmware crashes we check for the value
'FW_IND_EVENT_PENDING' in 'FW_INDICATOR_ADDRESS' and proceed with
disabling the irq and dumping firmware 'crash dump'. Now
when the PCI card is unplugged from the device the PCI controller
seems to generate a spurious interrupt after some time which
was as treated a firmware crash and resulting in the below race
condition (and eventually crashing the system)
ath10k_core_unregister -> ath10k_core_free_board_files
...... device unplug spurious interrupt .........
ath10k_pci_taklet -> ath10k_pci_fw_crashed_dump ...etc
Clearly even after the firmware board files related data structure
is freed up we are getting a spurious interrupt from PCI with 0xfffffff
in the 'FW_INDICATOR_ADDRESS' resulting in scheduling of the pci tasklet
and doing a crash dump, printing f/w board related info resulting in the
below crash. Fix this by detecting this spurious interrupt in ath10k PCI
irq handler itself and return IRQ_NONE. Thanks to Michal Kazior for
helping us conclude the most appropriate fix.
Call trace:
EIP is at ath10k_debug_print_board_info+0x39/0xb0
[ath10k_core]
EAX: 00000000 EBX: d4de15a0 ECX: 00000000 EDX: 00000064
ESI: f615ddd0 EDI: f8530000 EBP: f615de3c ESP: f615ddbc
DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
CR0: 80050033 CR2: 00000004 CR3: 01c0a000 CR4: 000006f0
Stack:
f615ddd0 00000064 f8b4ecdd 00000000 00000000 00412f4e
00000000 00000000
00000000 00000000 00000000 00000000 00000000 00000000
00000000 00000000
00000000 00000000 00000000 00000000 00000000 00000000
00000000 00000000
Call Trace:
[<f8b1f517>] ath10k_print_driver_info+0x17/0x30
[ath10k_core]
[<f875463a>] ath10k_pci_fw_crashed_dump+0x7a/0xe0
[ath10k_pci]
[<f87549d0>] ath10k_pci_tasklet+0x70/0x90 [ath10k_pci]
[<c106151e>] tasklet_action+0x9e/0xb0
Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Several cases of overlapping changes, except the packet scheduler
conflicts which deal with the addition of the free list parameter
to qdisc_enqueue().
Signed-off-by: David S. Miller <davem@davemloft.net>
ath.git patches for 4.8. Major changes:
ath10k
* enable btcoex support without restarting firmware
* enable ipq4019 support using AHB bus
* add QCA9887 chipset support
* retrieve calibration data from EEPROM, currently only for QCA9887
wil6210
* add pm_notify handling
The nl80211 layer expects P2P search operation to be aborted
if needed when stopping P2P device. If the P2P search operation
is still running after returning from stop_p2p_device
it causes a WARN_ON and possibly a kernel crash.
Fix this by aborting the P2P search in wil_cfg80211_stop_p2p_device
and preventing P2P search from being started on a stopped P2P
device.
Note, the fix does not cover the case where a regular scan
is started on the P2P device. It will be completed in the
future when support is added for aborting a scan operation.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In wil_p2p_listen chan is checked to protect against NULL
pointer access only before setting channel = chan->hw_value.
Add a global parameter check to cover all accesses to chan.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In this switch statement, the default case does not always assign
sifs. In practice, ah->ah_bwmode cannot take values besides the
other labels, so this is not an actual problem, but it looks odd
and smatch complains thus:
ath5k_hw_get_default_sifs() warn: missing break? reassigning 'sifs'
Silence the warning by moving default label up a line.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
commit 5c86d97bcc ("ath10k: combine txrx and replenish task")
introduced deadlock while processing rx in order indication message
for qca6174 based devices. While merging replenish and txrx tasklets,
replenish task should be called out of htt rx ring locking since it
is also try to acquire the same lock.
Unfortunately this issue is not exposed by other solutions (qca988x,
qca99x0 & qca4019), as rx_in_ord_ind message is specific to qca6174
based devices. This patch fixes
=============================================
[ INFO: possible recursive locking detected ]
4.7.0-rc2-wt-ath+ #1353 Tainted: G E
---------------------------------------------
swapper/3/0 is trying to acquire lock:
(&(&htt->rx_ring.lock)->rlock){+.-...}, at: [<f8d7ef19>]
ath10k_htt_rx_msdu_buff_replenish+0x29/0x90 [ath10k_core]
but task is already holding lock:
(&(&htt->rx_ring.lock)->rlock){+.-...}, at: [<f8d82cab>]
ath10k_htt_txrx_compl_task+0x21b/0x250 [ath10k_core]
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&(&htt->rx_ring.lock)->rlock);
lock(&(&htt->rx_ring.lock)->rlock);
*** DEADLOCK ***
May be due to missing lock nesting notation
1 lock held by swapper/3/0:
#0: (&(&htt->rx_ring.lock)->rlock){+.-...}, at: [<f8d82cab>]
ath10k_htt_txrx_compl_task+0x21b/0x250 [ath10k_core]
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=119151
Fixes: 5c86d97bcc ("ath10k: combine txrx and replenish task")
Reported-by: Mike Lothian <mike@fireburn.co.uk>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In QCA4019, cycle counter wraparound is not tied to rx
clear counter. Each counter would wraparound individually
and after wraparound the respective counter will be reset
to 0x7fffffff while other counter still running unaffected.
Define a new wraparound type for this behaviour and handle
it separately so that rx clear counter wraparound is also
handled just like cycle counter. With this type of
wraparound we can accurately compute and report channel
active/busy time when any of the counter overflows.
Fixes: ee9ca147c5 ("ath10k: Fix survey reporting with QCA4019")
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA988X hw implements a different cycle counter wraparound
behaviour when compared to QCA4019. To properly handle different
wraparound logic for these chipsets replace already available
bool hw_params member, has_shifted_cc_wraparound, with an
enum which could be extended to handle different wraparound
behaviour. This patch keeps the existing logic functionally
same and a prepares cycle counter wraparound handling to
extend for other chips.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
[kvalo@qca.qualcomm.com: change also QCA9887 wrap type]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
CCK hardware table mapping from QCA99X0 onwards got revised.
The CCK hardware rate values are in a proper order wrt. to
rate and preamble as below
ATH10K_HW_RATE_REV2_CCK_LP_1M = 1,
ATH10K_HW_RATE_REV2_CCK_LP_2M = 2,
ATH10K_HW_RATE_REV2_CCK_LP_5_5M = 3,
ATH10K_HW_RATE_REV2_CCK_LP_11M = 4,
ATH10K_HW_RATE_REV2_CCK_SP_2M = 5,
ATH10K_HW_RATE_REV2_CCK_SP_5_5M = 6,
ATH10K_HW_RATE_REV2_CCK_SP_11M = 7,
This results in reporting of rx frames (with CCK rates)
totally wrong for QCA99X0, QCA4019. Fix this by having
separate CCK rate table for these chipsets with rev2 suffix
and registering the correct rate mapping to mac80211 based on
the new hw_param (introduced) 'cck_rate_map_rev2' which shall
be true for any newchipsets from QCA99X0 onwards
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
All these flags are not used and their use is completely
covered by 'ath10k_hw_rate_ofdm', 'ath10k_hw_rate_cck',
and RX_PPDU_START_RATE_FLAG
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Only five bits are defined to pass tid information in HTT_RX_IND
message, so the mask which can be used to extract tid should be 0x1f
instead of the current 0x3f. Also, macros which can be used to extract
flush_valid and release_valid bits have to be left shifted one bit less
because these information follow the tid right after. This patch does
not really fix anything functionally because these macros are not used
currently.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This looks like a regression from commit c4cdf753ed ("ath10k: move
fw_features to struct ath10k_fw_file"), we were printing the features from a
wrong struct.
Fixes: c4cdf753ed ("ath10k: move fw_features to struct ath10k_fw_file")
Signed-off-by: Ben Greear <greearb@candelatech.com>
[kvalo@qca.qualcomm.com: improve commit log]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Ashok Raj Nagarajan