Commit Graph

190 Commits

Author SHA1 Message Date
Paulius Zaleckas f004f3ea34 phylib: make mdio-gpio work without OF (v4)
make mdio-gpio work with non OpenFirmware gpio implementation.

Aditional changes to mdio-gpio:
- use gpio_request() and gpio_free()
- place irq[] array in struct mdio_gpio_info
- add module description, author and license
- add note about compiling this driver as module
- rename mdc and mdio function (were ugly names)
- change MII to MDIO in bus name
- add __init __exit to module (un)loading functions
- probe fails if no phys added to the bus
- kzalloc bitbang with sizeof(*bitbang)

Changes since v3:
- keep bus naming "%x" to be compatible with existing drivers.

Changes since v2:
- more #ifdefs reduction
- platform driver will be registered on OF platforms also
- unified platform and OF bus_id to phy%i

Changes since v1:
- removed NO_IRQ
- reduced #idefs

Laurent, please test this driver under OF.

Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-16 18:59:45 -08:00
Paulius Zaleckas 72af187f21 phylib: rename mdio-ofgpio to mdio-gpio
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-16 18:59:24 -08:00
Giulio Benetti 3ee82383f0 phy: fix phy address bug
PHYID returns 0xffff and not 0xffffffff when not found and in some
case(at91sam9263) 0x0. Maybe this patch could be useful.

Signed-off-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-16 01:49:41 -08:00
Ron Madrid 605f196efb phy: Add support for Marvell 88E1118 PHY
This patch will add support for the Marvell 88E1118 PHY which supports gigabit ethernet among other things.

Signed-off-by: Ron Madrid <ron_madrid@sbcglobal.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-15 14:04:27 -08:00
Lennert Buytenhek 3e44017b58 phylib: fix premature freeing of struct mii_bus
Commit 46abc02175 ("phylib: give mdio
buses a device tree presence") added a call to device_unregister() in
a situation where the caller did not intend for the device to be
freed yet, but apart from just unregistering the device from the
system, device_unregister() does an additional put_device() that is
intended to free it.

The right function to use in this situation is device_del(), which
unregisters the device from the system like device_unregister() does,
but without dropping the reference count an additional time.

Bug report from Bryan Wu <cooloney@kernel.org>.

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-11-14 18:19:40 -05:00
Kay Sievers fb28ad3590 net: struct device - replace bus_id with dev_name(), dev_set_name()
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-10 13:55:14 -08:00
Steve Glendinning fd9abb3d97 SMSC LAN911x and LAN921x vendor driver
Attached is a driver for SMSC's LAN911x and LAN921x families of embedded
ethernet controllers.

There is an existing smc911x driver in the tree; this is intended to
replace it.  Dustin McIntire (the author of the smc911x driver) has
expressed his support for switching to this driver.

This driver contains workarounds for all known hardware issues, and has
been tested on all flavours of the chip on multiple architectures.

This driver now uses phylib, so this patch also adds support for the
device's internal phy

Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: Bahadir Balban <Bahadir.Balban@arm.com>
Signed-off-by: Dustin Mcintire <dustin@sensoria.com>
Signed-off-by: Bill Gatliff <bgat@billgatliff.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-11-06 00:58:40 -05:00
Matt Carlson 772638b6c8 broadcom: Add support for BCM50610
This patch adds the BCM50610 to the list of phys supported by the
broadcom driver.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-03 16:56:51 -08:00
Matt Carlson 042a75b99f broadcom: Refine expansion register access routine
This patch makes the expansion register access routines a little more
formal.  They will be used by the following bcm50610 support patch.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-03 16:56:29 -08:00
Matt Carlson 5e0c676c71 broadcom: Add flow control support
This patch adds flow control support to Broadcom phys.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-03 16:56:07 -08:00
Greg Kroah-Hartman 26853ab6f9 NET: convert the phy_device file to use bus_find_device_by_name
The driver core now has this helper function, so might as well use it
instead of forcing the phy code to roll their own version.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-10-16 09:24:52 -07:00
Adrian Bunk 892871dcc3 net: export genphy_restart_aneg
This patch fixes the following build error caused by
commit ed94493fb3
(mv643xx_eth: convert to phylib):

<--  snip  -->

...
  Building modules, stage 2.
  MODPOST 1280 modules
ERROR: "genphy_restart_aneg" [drivers/net/mv643xx_eth.ko] undefined!
...
make[2]: *** [__modpost] Error 1

<--  snip  -->

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-13 18:48:09 -07:00
Randy Dunlap 78c36b15a0 net/phy: add missing kernel-doc
Fix kernel-doc warning, missing description:

Warning(lin2627-g3-kdocfixes//drivers/net/phy/mdio_bus.c:63): No description found for parameter 'd'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-13 18:46:22 -07:00
Lennert Buytenhek ec2a5652ea phylib: two dynamic mii_bus allocation fallout fixes
1. arch/powerpc/platforms/pasemi/gpio_mdio.c also needs to be
   converted over to mdiobus_{alloc,free}().

2. drivers/net/phy/fixed.c used to embed a struct mii_bus into its
   struct fixed_mdio_bus and then use container_of() to go from the
   former to the latter.  Since mii bus structures are no longer
   embedded, we need to do something like use the mii bus private
   pointer to go from mii_bus to fixed_mdio_bus instead.

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-09 09:45:04 -07:00
Lennert Buytenhek 2e88810329 phylib: add mdiobus_{read,write}
Add mdiobus_{read,write} routines to allow direct reading/writing
of registers on an mii bus without having to go through the PHY
abstraction, and make phy_{read,write} use these primitives.

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-08 16:38:41 -07:00
Lennert Buytenhek 46abc02175 phylib: give mdio buses a device tree presence
Introduce the mdio_bus class, and give each 'struct mii_bus' its own
'struct device', so that mii_bus objects are represented in the device
tree and can be found by querying the device tree.

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-08 16:33:40 -07:00
Lennert Buytenhek 298cf9beb9 phylib: move to dynamic allocation of struct mii_bus
This patch introduces mdiobus_alloc() and mdiobus_free(), and
makes all mdio bus drivers use these functions to allocate their
struct mii_bus'es dynamically.

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Andy Fleming <afleming@freescale.com>
2008-10-08 16:29:57 -07:00
Lennert Buytenhek 18ee49ddb0 phylib: rename mii_bus::dev to mii_bus::parent
In preparation of giving mii_bus objects a device tree presence of
their own, rename struct mii_bus's ->dev argument to ->parent, since
having a 'struct device *dev' that points to our parent device
conflicts with introducing a 'struct device dev' representing our own
device.

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Andy Fleming <afleming@freescale.com>
2008-10-08 16:27:49 -07:00
Trent Piepho 0acb283967 phylib: Wake PHY state machine on interrupt
This way the phy layer will respond to a change in phy state immediately,
instead of up to one second later when the state machine timer runs.

Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-08 15:46:57 -07:00
Trent Piepho 51e2a3846e PHY: Avoid unnecessary aneg restarts
The PHY's aneg is configured and restarted whenever the link is brought up,
e.g. when DHCP is started after the kernel has booted.  This can take the
link down for several seconds while auto-negotiation is redone.

If the advertised features haven't changed, then it shouldn't be necessary
to bring down the link and start auto-negotiation over again.

genphy_config_advert() is enhanced to return 0 when the advertised features
haven't been changed and >0 when they have been.

genphy_config_aneg() then uses this information to not call
genphy_restart_aneg() if there has been no change.

Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-08 15:43:54 -07:00
Lennert Buytenhek c6d6a511d7 phylib: phy_mii_ioctl() fixes
Make the SIOCGMIIPHY case fall through properly (it is supposed
to not only return the ID of the default PHY but also to read from
that PHY), and make phy_mii_ioctl() return the same error code as
generic_mii_ioctl() in case of an unsupported operation.

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-08 15:24:56 -07:00
Lennert Buytenhek 4fd5f812c2 phylib: allow incremental scanning of an mii bus
This patch splits the bus scanning code in mdiobus_register() off
into a separate function, and makes this function available for
calling from external code.  This allows incrementally scanning an
mii bus, e.g. as information about which addresses are 'safe' to
scan becomes available.

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Andy Fleming <afleming@freescale.com>
2008-09-19 05:13:54 +02:00
Wang Jian 7239016d52 net/phy: Fix 88e1111 copper/fiber selection in RGMII mode
MII_M1111_HWCFG_FIBER_COPPER_RES is a bit of MII_M1111_PHY_EXT_SR, not
MII_M1111_PHY_EXT_CR.

Signed-off-by: Wang Jian <lark@linux.net.cn>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-22 17:59:12 -04:00
Wang Jian 9cf8fa4334 net/phy: Fix copper/fiber auto-selection for 88e1111
The 27.15 bit (MII_M1111_HWCFG_FIBER_COPPER_AUTO) is disable bit. When
set to 1, copper/fiber auto selection is disabled. The current code
to enable but actually disable auto selection.

Signed-off-by: Wang Jian <lark@linux.net.cn>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-22 17:58:10 -04:00
Takashi Iwai e9911c2c8f Fix missing exports for net/phy/mdio-bitbang.c
{alloc,free}_mdio_bitbang() are not exported while they are used in
mdio-ofgpio driver.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-11 01:20:34 -04:00
Laurent Pinchart a5edeccb1a net: OpenFirmware GPIO based MDIO bitbang driver
This patch adds an MDIO bitbang driver that uses the GPIO library and its
OF bindings to access the bus I/Os.

Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-30 22:18:25 -04:00
David S. Miller a5b17df04c Merge branch 'upstream-next-davem' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6 2008-05-29 03:31:03 -07:00
Paul Gortmaker a01b3d766c phylib: do EXPORT_SYMBOL on get_phy_id
Commit cac1f3c8 factored out the code for get_phy_id so that it
could be reused in multiple places.  Turns out that some of the
users can be modular, so we need to export this symbol as well.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-22 14:01:01 -04:00
Maciej W. Rozycki 1b0771ab3e PHYLIB: Kconfig: Complete the list of Broadcom PHYs supported
Add Broadcom PHYs supported missing from the description.

Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-22 06:34:32 -04:00
Nate Case cd9af3dac6 PHYLIB: Add 1000Base-X support for Broadcom bcm5482
Configure the BCM5482S secondary SerDes for 1000Base-X mode when the
appropriate dev_flags are passed in to phy_connect().  This is
needed when the PHY is used for fiber and backplane connections.

Signed-off-by: Nate Case <ncase@xes-inc.com>
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-22 06:34:31 -04:00
Maciej W. Rozycki 940608be2e PHYLIB: Kconfig: Fix the dependency on S390
PHYLIB was first marked as BROKEN on S390, then the enclosing menu marked
as non-S390, then the two dependencies merged with the conversion to
menuconfig.  Reduce to non-S390.

Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-22 06:19:22 -04:00
Andy Fleming 9b9a8bfc8d phylib: Fix some sparse warnings
Declared some things static, declared some things in the header.

Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-06 12:01:41 -04:00
Steve Glendinning 4d9b1a022a Add support for SMSC LAN8187 and LAN8700 PHYs
Add support for two additional SMSC PHY models with identical interrupt
source and mask registers to the LAN83C185

Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-29 01:55:59 -04:00
Steve Glendinning 48c41b9941 Rename SMSC phy functions to be more generic
Several models of SMSC PHY have the same interrupt status and mask
registers as the LAN83C185, so these functions can service multiple
different PHY drivers.

Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-29 01:55:57 -04:00
Randy Dunlap 5d12b132bc drivers/net/phy: fix kernel-doc notation
Fix kernel-doc warning:
Warning(linux-2.6.25-git11//drivers/net/phy/phy_device.c:275): No
description found for parameter 'bus_id'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-29 01:55:55 -04:00
Andy Fleming f62220d3a9 phylib: Add support for board-level PHY fixups
Sometimes the specific interaction between the platform and the PHY
requires special handling.  For instance, to change where the PHY's
clock input is, or to add a delay to account for latency issues in the
data path.  We add a mechanism for registering a callback with the PHY
Lib to be called on matching PHYs when they are brought up, or reset.

Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-25 02:08:52 -04:00
Paul Gortmaker cac1f3c8a8 phylib: factor out get_phy_id from within get_phy_device
We were already doing what amounts to a get_phy_id from within
get_phy_device, and rather than duplicate this for the TBIPA
probing, we might as well just factor it out and make it available
instead.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-17 15:31:33 -04:00
Paul Gortmaker b1394f961a PHY: add BCM5464 support to broadcom PHY driver
The BCM5464 can be used with the current broadcom PHY driver
by just adding the appropriate chip ID and using the existing
support within.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-17 15:31:32 -04:00
Andy Fleming 9d9326d3bc phy: Change mii_bus id field to a string
Having the id field be an int was making more complex bus topologies
excessively difficult.  For now, just convert it to a string, and
change all instances of "bus->id = val" to
snprintf(id, MII_BUS_ID_LEN, "%x", val).

Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-16 20:09:35 -04:00
David S. Miller df39e8ba56 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:

	drivers/net/ehea/ehea_main.c
	drivers/net/wireless/iwlwifi/Kconfig
	drivers/net/wireless/rt2x00/rt61pci.c
	net/ipv4/inet_timewait_sock.c
	net/ipv6/raw.c
	net/mac80211/ieee80211_sta.c
2008-04-14 02:30:23 -07:00
Harvey Harrison 5da4e37e59 net: marvell.c fix sparse shadowed variable warning
The other if blocks don't redeclare temp, remove the redeclaration in
the final if() block.

drivers/net/phy/marvell.c:214:7: warning: symbol 'temp' shadows an earlier one
drivers/net/phy/marvell.c:160:6: originally declared here

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-04 17:26:15 -04:00
David S. Miller 8e8e43843b Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:

	drivers/net/usb/rndis_host.c
	drivers/net/wireless/b43/dma.c
	net/ipv6/ndisc.c
2008-03-27 18:48:56 -07:00
Anton Vorontsov 57bb7e2228 phy/broadcom: add support for BCM5481 PHY
This patch adds support for BCM5481 PHY. Unfortunately it's hard to
get specifications for this PHY, so its special register 0x18 isn't
annotated properly (but we know it's used to set up the delays).

I've kept the magic numbers, so we'll not forget to fix it at the
first opportunity, and will name that register and its bits correctly.

p.s. also fixed the line with broken indention, introduced by
commit 03157ac31e
    PHYLIB: Add BCM5482 PHY support

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-03-26 00:19:56 -04:00
Jeff Garzik f0c88f9c45 netxen, phy/marvell, skge: minor checkpatch fixes
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-03-25 23:53:24 -04:00
Alexandr Smirnov be937f1f89 Marvell PHY m88e1111 driver fix
Marvell PHY m88e1111 (not sure about other models, but think they too)
works in two modes: fiber and copper. In Marvell PHY driver (that we
have in current community kernels) code supported only copper mode,
and this is not configurable, bits for copper mode are simply written
in registers during PHY initialization.

This patch adds support for both modes.

Signed-off-by: Alexandr Smirnov <asmirnov@ru.mvista.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-03-25 23:16:52 -04:00
Adrian Bunk f9e7d100dd FIXED_PHY must depend on PHYLIB=y
This patch fixes the following build error introduced by commit
a79d8e93d3 and reported by Olaf Hering:

<--  snip  -->

...
  LD      .tmp_vmlinux1
arch/powerpc/sysdev/built-in.o: In function `of_add_fixed_phys':
fsl_soc.c:(.init.text+0xd34): undefined reference to `fixed_phy_add'
make: *** [.tmp_vmlinux1] Error 1

<--   snip  -->

Signed-off-by: Adrian Bunk <adrian.bunk@movial.fi>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-03-05 06:34:34 -05:00
frederic Rodo 8b7c166440 dm9161: add configuration for MII/RMII
Signed-off-by: Frederic Rodo <f.rodo@til-technologies.fr>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-03-05 06:26:56 -05:00
Adrian Bunk d1e7fe4d92 net/phy/mdio_bus.c: fix a check-after-use
This patch fixes a check-after-use spotted by the Coverity checker.

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-23 23:57:50 -05:00
Adrian Bunk 651be3a2ba net/phy/fixed.c: fix a use-after-free
This patch fixes a use-after-free introduced by
commit a79d8e93d3 and spotted by the
Coverity checker.

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-11 11:15:36 -05:00
Johnson Leung 097c2aa89f phylib: Add Realtek 821x eth PHY support
this PHY present on the MPC8315E and MPC837xE RDB boards.

Signed-off-by: Johnson Leung <r58129@freescale.com>
Signed-off-by: Kevin Lam <r43770@freescale.com>
Signed-off-by: Joe D'Abbraccio <ljd015@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-02-03 04:28:42 -08:00
Nate Case 35b5f6b1a8 PHYLIB: Locking fixes for PHY I/O potentially sleeping
PHY read/write functions can potentially sleep (e.g., a PHY accessed
via I2C).  The following changes were made to account for this:

    * Change spin locks to mutex locks
    * Add a BUG_ON() to phy_read() phy_write() to warn against
      calling them from an interrupt context.
    * Use work queue for PHY state machine handling since
      it can potentially sleep
    * Change phydev lock from spinlock to mutex

Signed-off-by: Nate Case <ncase@xes-inc.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-02-03 04:28:41 -08:00
Nate Case 03157ac31e PHYLIB: Add BCM5482 PHY support
This Broadcom PHY is similar to other bcm54xx devices.

Signed-off-by: Nate Case <ncase@xes-inc.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-02-03 04:26:28 -08:00
Vitaly Bordug a79d8e93d3 phy/fixed.c: rework to not duplicate PHY layer functionality
With that patch fixed.c now fully emulates MDIO bus, thus no need
to duplicate PHY layer functionality. That, in turn, drastically
simplifies the code, and drops down line count.

As an additional bonus, now there is no need to register MDIO bus
for each PHY, all emulated PHYs placed on the platform fixed MDIO bus.
There is also no more need to pre-allocate PHYs via .config option,
this is all now handled dynamically.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-01-23 19:33:58 -06:00
Anton Vorontsov 6f4a7f4183 PHY: Add the phy_device_release device method.
Lately I've got this nice badness on mdio bus removal:

Device 'e0103120:06' does not have a release() function, it is broken and must be fixed.
------------[ cut here ]------------
Badness at drivers/base/core.c:107
NIP: c015c1a8 LR: c015c1a8 CTR: c0157488
REGS: c34bdcf0 TRAP: 0700   Not tainted  (2.6.23-rc5-g9ebadfbb-dirty)
MSR: 00029032 <EE,ME,IR,DR>  CR: 24088422  XER: 00000000
...
[c34bdda0] [c015c1a8] device_release+0x78/0x80 (unreliable)
[c34bddb0] [c01354cc] kobject_cleanup+0x80/0xbc
[c34bddd0] [c01365f0] kref_put+0x54/0x6c
[c34bdde0] [c013543c] kobject_put+0x24/0x34
[c34bddf0] [c015c384] put_device+0x1c/0x2c
[c34bde00] [c0180e84] mdiobus_unregister+0x2c/0x58
...

Though actually there is nothing broken, it just device
subsystem core expects another "pattern" of resource managment.

This patch implement phy device's release function, thus
we're getting rid of this badness.

Also small hidden bug fixed, hope none other introduced. ;-)

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-12-04 15:06:33 -05:00
David Woodhouse dda93b486a Stop phy code from returning success to unknown ioctls.
This kind of sucks, and prevents the Fedora installer from using the
device for network installs...

[root@efika phy]# iwconfig eth0
Warning: Driver for device eth0 has been compiled with an ancient version
of Wireless Extension, while this program support version 11 and later.
Some things may be broken...

eth0        ESSID:off/any  Nickname:""
          NWID:0  Channel:0  Access Point: 00:00:BF:81:14:E0
          Bit Rate:-1.08206e+06 kb/s   Sensitivity=0/0
          RTS thr:off   Fragment thr:off
          Encryption key:<too big>
          Power Management:off

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-12-01 16:35:51 -05:00
Kim Phillips 9daf5a7695 phylib: marvell: add support for TX-only and RX-only Internal Delay
Previously, Internal Delay specification implied the delay be
applied to both TX and RX.  This patch allows for separate TX/RX-only
internal delay specification.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Tested-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-12-01 16:32:30 -05:00
Olof Johansson f2511f13da phylib: Silence driver registration
It gets quite verbose to see every single PHY driver being registered
by default.

Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-11-05 17:58:36 -05:00
Olof Johansson ac8c635abb phylib: Add ID for Marvell 88E1240
Add PHY IDs for Marvell 88E1240. It seems to have close enough programming
models to 1111/1112 for basic support at least.

Also clean up whitespace in the ID list a bit.

Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-11-05 17:58:36 -05:00
Randy Dunlap 5a46236d20 phy/bitbang: missing MODULE_LICENSE
Missing MODULE_LICENSE(), loading this module taints the kernel.

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-19 23:00:01 -04:00
Scott Wood e2ec4581ad Generic bitbanged MDIO library
Previously, bitbanged MDIO was only supported in individual
hardware-specific drivers.  This code factors out the higher level
protocol implementation, reducing the hardware-specific portion to
functions setting direction, data, and clock.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-10 16:54:03 -07:00
Maciej W. Rozycki 6daf653103 PHYLIB: fix an interrupt loop potential when halting
Ensure the PHY_HALTED state is not entered with the IRQ asserted as it
could lead to an interrupt loop.

There is a small window in phy_stop(), where the state of the PHY machine
indicates it has been halted, but its interrupt output might still be
unmasked.  If an interrupt goes active right at this moment it will loop as
the phy_interrupt() handler exits immediately with IRQ_NONE if the halted
state is seen.  It is unsafe to extend the phydev spinlock to cover
phy_interrupt().  It is safe to swap the order of the actions though as all
the competing places to unmask the interrupt output of the PHY, which are
phy_change() and phy_timer() are already covered with the lock as is the
sequence in question.

Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-10 16:53:55 -07:00
Maciej W. Rozycki 0ac4952731 PHYLIB: IRQ event workqueue handling fixes
Keep track of disable_irq_nosync() invocations and call enable_irq() the
right number of times if work has been cancelled that would include them.

Now that the call to flush_work_keventd() (problematic because of
rtnl_mutex being held) has been replaced by cancel_work_sync() another
issue has arisen and been left unresolved.  As the MDIO bus cannot be
accessed from the interrupt context the PHY interrupt handler uses
disable_irq_nosync() to prevent from looping and schedules some work to be
done as a softirq, which, apart from handling the state change of the
originating PHY, is responsible for reenabling the interrupt.  Now if the
interrupt line is shared by another device and a call to the softirq
handler has been cancelled, that call to enable_irq() never happens and the
other device cannot use its interrupt anymore as its stuck disabled.

I decided to use a counter rather than a flag because there may be more
than one call to phy_change() cancelled in the queue -- a real one and a
fake one triggered by free_irq() if DEBUG_SHIRQ is used, if nothing else.
Therefore because of its nesting property enable_irq() has to be called the
right number of times to match the number disable_irq_nosync() was called
and restore the original state.  This DEBUG_SHIRQ feature is also the
reason why free_irq() has to be called before cancel_work_sync().

While at it I updated the comment about phy_stop_interrupts() being called
from `keventd' -- this is no longer relevant as the use of
cancel_work_sync() makes such an approach unnecessary.  OTOH a similar
comment referring to flush_scheduled_work() in phy_stop() still applies as
using cancel_work_sync() there would be dangerous.

Checked with checkpatch.pl and at the run time (with and without
DEBUG_SHIRQ).

Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-10 16:53:55 -07:00
Maciej W. Rozycki 9ff8c68b3c PHYLIB: Spinlock fixes for softirqs
Use spin_lock_bh()/spin_unlock_bh() for the phydev lock throughout as it
is used in phy_timer() that is called as a softirq and all the other
operations may happen in the user context.

There has been a change recently that did such a conversion for some of the
operations on the lock, but some have been left intact.  Many of them,
perhaps all, may be called in the user context and I was able to trigger
recursive spinlock acquisition indeed, so I think for the sake of long-term
maintenance it is best to convert them all, even if unnecessarily for one
or two -- better safe than sorry.

Perhaps one in phy_timer() could actually be skipped as only called as a
softirq -- I can send an update if that sounds like a good idea.

Checked with checkpatch.pl and at the runtime.

Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-10 16:53:54 -07:00
Vitaly Bordug 7c32f470f4 PHY fixed driver: rework release path and update phy_id notation
device_bind_driver() error code returning has been fixed.  release()
function has been written, so that to free resources in correct way; the
release path is now clean.

Before the rework, it used to cause
 Device 'fixed@100:1' does not have a release() function, it is broken
 and must be fixed.
 BUG: at drivers/base/core.c:104 device_release()

 Call Trace:
  [<ffffffff802ec380>] kobject_cleanup+0x53/0x7e
  [<ffffffff802ec3ab>] kobject_release+0x0/0x9
  [<ffffffff802ecf3f>] kref_put+0x74/0x81
  [<ffffffff8035493b>] fixed_mdio_register_device+0x230/0x265
  [<ffffffff80564d31>] fixed_init+0x1f/0x35
  [<ffffffff802071a4>] init+0x147/0x2fb
  [<ffffffff80223b6e>] schedule_tail+0x36/0x92
  [<ffffffff8020a678>] child_rip+0xa/0x12
  [<ffffffff80311714>] acpi_ds_init_one_object+0x0/0x83
  [<ffffffff8020705d>] init+0x0/0x2fb
  [<ffffffff8020a66e>] child_rip+0x0/0x12

Also changed the notation of the fixed phy definition on
mdio bus to the form of <speed>+<duplex> to make it able to be used by
gianfar and ucc_geth that define phy_id strictly as "%d:%d" and cleaned up
the whitespace issues.

Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-10 16:53:50 -07:00
Denis Cheng ff8ac60948 drivers/net/: all drivers/net/ cleanup with ARRAY_SIZE
Signed-off-by: Denis Cheng <crquan@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-10 16:51:15 -07:00
Domen Puncer 680e9fe9d6 phy: export phy_mii_ioctl
Export phy_mii_ioctl, so network drivers can use it when built
as modules too.

Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-09-20 02:35:50 -04:00
Hans-Jürgen Koch 026d7917e5 Fix a lock problem in generic phy code
Lock debugging finds a problem in phy.c and phy_device.c,
this patch fixes it. Tested on an AT91SAM9263-EK board,
kernel 2.6.23-rc4.

Signed-off-by: Hans J. Koch <hjk@linutronix.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-09-13 00:12:43 -04:00
Domen Puncer bc1e0a095e phy layer: fix genphy_setup_forced (don't reset)
Writing BMCR_RESET bit will reset MII_BMCR to default values. This is
clearly not what we want.

Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-25 02:31:02 -04:00
Domen Puncer 163642a24a phy layer: fix phy_mii_ioctl for autonegotiation
Fix a thinko (?) in setting phydev->autoneg.

Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-07 17:34:13 -04:00
Andy Fleming 52cb1c2b70 Fix error checking in Vitesse IRQ config
phy_read() returns a negative number if there's an error, but the
error-checking code in the Vitesse driver's config_intr function
triggers if phy_read() returns non-zero.  Correct that.

Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-24 16:28:41 -04:00
Andy Fleming af2d940df2 Fix Vitesse RGMII-ID support
The Vitesse PHY on the 8641D needs to be set up with internal delay to
work in RGMII mode.  So we add skew when it is set to RGMII_ID mode.

Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Haruki Dai <Dai.Haruki@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
2007-07-18 18:29:37 -04:00
Andy Fleming 1d5e83aac5 Fix Vitesse 824x PHY interrupt acking
The Vitesse 824x PHY doesn't allow an interrupt to be cleared if
the mask bit for that interrupt isn't set.  This means that the PHY
Lib's order of handling interrupts (disable, then clear) breaks on this
PHY.  However, clearing then disabling the interrupt opens up the code
for a silly race condition.  So rather than change the PHY Lib, we change
the Vitesse driver so it always clears interrupts before disabling them.
Further, the ack function only clears the interrupt if interrupts are
enabled.

Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Acked-by: Haiying Wang <Haiying.Wang@freescale.com>
2007-07-18 18:29:37 -04:00
Olof Johansson 85cfb53428 phylib: Add Marvell 88E1112 phy id
Add 88E1112 PHY ID to the marvell driver. Seems to do fine with the
88E1111 inits.

Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-10 12:41:09 -04:00
Olof Johansson e54792396f phylib: cleanup marvell.c a bit
Simplify the marvell driver init a bit: Make the supported devices an
array instead of explicitly registering each structure. This makes it
considerably easier to add new devices down the road.

Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-10 12:41:09 -04:00
Kapil Juneja 4117b5be4b phylib: m88e1111: enable SGMII mode
If connected via SGMII, initialize with SGMII mode configured.

Signed-off-by: Kapil Juneja <Kapil.Juneja@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-08 22:16:38 -04:00
Michael Barkowski 0cefeebaf3 phylib: add the ICPlus IP175C PHY driver
The ICPlus IP175C sports a 100Mbit/s 4-port switch in addition
to a dedicated 100Mbit/s WAN port.

Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-08 22:16:38 -04:00
Kumar Gala 5f708dd91d phy: Fix phy_id for Vitesse 824x PHY
The phy_id specified for the Vitesse 824x PHY would never match because
it was expecting bits to be set that would be masked by the phy_id_mask.
Fix the phy_id so it will match properly, and changed the mdio_bus_match
to mask both the driver and devices phy_id with the mask so we dont have
this issue in the future.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2007-06-28 13:26:06 -05:00
Kim Phillips 895ee682db phylib: add RGMII-ID mode to the Marvell m88e1111 PHY to fix broken ucc_geth
Support for configuring RGMII-ID (RGMII with internal delay) mode on the
88e1111 and 88e1145.  Ucc_geth on MPC8360EMDS(the main user of ucc_geth)
is broken after changed to use phylib.  It is fixed by adding this
internal delay.

Also renamed 88e1111s -> 88e1111 (no references to an 88e1111s part were
found), and fixed some whitespace.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-06-09 18:25:35 -04:00
Denver Gingerich 239dc572b8 fix compiler warning in fixed.c
Correct the following compiler warning (and warnings resulting from
the correction):
warning: 'fixed_mdio_register_device' defined but not used

Signed-off-by: Denver Gingerich <denver@ossguy.com>
Cc: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-24 17:20:49 -04:00
Kim Phillips 12414db11d Add support for the Davicom DM9161A PHY
Distinguish between the Davicom DM9161A PHY and the DM9161E.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-11 17:53:43 -04:00
Jan Engelhardt 53f99941c1 Use menuconfig objects: PHY
Use menuconfigs instead of menus, so the whole menu can be disabled at once
instead of going through all options.

Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-11 17:53:16 -04:00
Martin Schwidefsky 9556fb73ed [S390] Kconfig: unwanted menus for s390.
Disable some more menus in the configuration files that are of no
interest to a s390 machine.

Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2007-05-10 15:46:07 +02:00
Oleg Nesterov 28e53bddf8 unify flush_work/flush_work_keventd and rename it to cancel_work_sync
flush_work(wq, work) doesn't need the first parameter, we can use cwq->wq
(this was possible from the very beginnig, I missed this).  So we can unify
flush_work_keventd and flush_work.

Also, rename flush_work() to cancel_work_sync() and fix all callers.
Perhaps this is not the best name, but "flush_work" is really bad.

(akpm: this is why the earlier patches bypassed maintainers)

Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Auke Kok <auke-jan.h.kok@intel.com>,
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-09 12:30:53 -07:00
Andrew Morton d0758bc334 phy: use flush_work_keventd()
(akpm: bypassed maintainers, sorry.  There are other patches which depend on
this)

Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-09 12:30:51 -07:00
Shan Lu 024a0a3cfb network: add the missing phy_device speed information to phy_mii_ioctl
Function `phy_mii_ioctl' returns physical device's information based on
user requests.  When requested to return the basic mode control register
information (BMCR), the original implementation only returns the physical
device's duplex information and forgets to return speed information, which
should not be because BMCR register is used to hold both duplex and speed
information.

The patch checks the BMCR value against speed-related flags and fills the
return structure's speed field accordingly.

Signed-off-by: Shan <shanlu@cs.uiuc.edu>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-04-28 11:00:57 -04:00
Randy Dunlap b3df0da886 phy layer: add kernel-doc + DocBook
Convert function documentation in drivers/net/phy/ to kernel-doc
and add it to DocBook.

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-04-28 11:00:57 -04:00
Greg Kroah-Hartman 87aebe078e PHY: remove rwsem use from phy core
The subsystem rwsem is not used by the driver core at all, so the use of
it in the phy code doesn't make any sense.  They might possibly
want to use a local lock, but I am unsure about that.

Cc: netdev <netdev@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-04-27 10:57:31 -07:00
Andy Fleming 76884679c6 phylib: Add support for Marvell 88e1111S and 88e1145
Changes include:
* New support for 88e1145
* New support for 88e111s
* Fixing 88e1101 driver to not match non-88e1101 PHYs
* Increases in feature support across Marvell PHY product line
* Fixes a bunch of whitespace issues found by Lindent

Signed-off-by: Andrew Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-17 15:16:08 -05:00
Jeff Garzik f630fe2817 Merge branch 'master' into upstream 2007-02-17 15:11:43 -05:00
Tim Schmielau cd354f1ae7 [PATCH] remove many unneeded #includes of sched.h
After Al Viro (finally) succeeded in removing the sched.h #include in module.h
recently, it makes sense again to remove other superfluous sched.h includes.
There are quite a lot of files which include it but don't actually need
anything defined in there.  Presumably these includes were once needed for
macros that used to live in sched.h, but moved to other header files in the
course of cleaning it up.

To ease the pain, this time I did not fiddle with any header files and only
removed #includes from .c-files, which tend to cause less trouble.

Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha,
arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig,
allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all
configs in arch/arm/configs on arm.  I also checked that no new warnings were
introduced by the patch (actually, some warnings are removed that were emitted
by unnecessarily included header files).

Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-02-14 08:09:54 -08:00
Randy Dunlap 1a1689344a phy devices: use same arg types
sparse complains about differing types from prototype to
definition, so change the u32 to phy_interface_t:

drivers/net/phy/phy_device.c:140:19: error: symbol 'phy_connect' redeclared with different type (originally declared at include/linux/phy.h:362) - incompatible argument 5 (different signedness)
drivers/net/phy/phy_device.c:190:19: error: symbol 'phy_attach' redeclared with different type (originally declared at include/linux/phy.h:360) - incompatible argument 4 (different signedness)

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-09 16:34:13 -05:00
Vitaly Bordug b1f54ba34f FS_ENET: OF-related fixup for FEC and SCC MAC's
Updated direct resource pass with ioremap call, make it grant proper IRQ
mapping, stuff incompatible with the new approach were respectively put
under #ifndef CONFIG_PPC_MERGE.  It is required so that both ppc and
powerpc could utilize fs_enet effectively.

Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-01-30 09:36:01 -05:00
Kumar Gala 9f6d55d084 PHY: Export phy ethtool helpers
We need to export phy_ethtool_gset and phy_ethtool_sset to allow drivers that
use these functions to be built as modules.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-01-23 00:51:33 -05:00
Robert P. J. Day cd86128088 [PATCH] Fix numerous kcalloc() calls, convert to kzalloc()
All kcalloc() calls of the form "kcalloc(1,...)" are converted to the
equivalent kzalloc() calls, and a few kcalloc() calls with the incorrect
ordering of the first two arguments are fixed.

Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Greg KH <greg@kroah.com>
Cc: Mark Fasheh <mark.fasheh@oracle.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-13 09:05:52 -08:00
Linus Torvalds 68380b5813 Add "run_scheduled_work()" workqueue function
This allows workqueue users to run just their own pending work, rather
than wait for the whole workqueue to finish running.  This solves the
deadlock with networking libphy that was due to other workqueue entries
possibly needing a lock that was held by the routine that wanted to
flush its own work.

It's not wonderful: if you absolutely need to synchronize with the work
function having been executed, any user strictly speaking should have
its own completion tracking logic, since when we run things explicitly
by hand, the generic workqueue layer can no longer help us synchronize.

Also, this is strictly only usable for work that has been scheduled
without any delayed timers.  You can not mix the new interface with
schedule_delayed_work().

But it's better than what we had currently.

Acked-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-07 09:28:19 -08:00
David Howells 9db7372445 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6
Conflicts:

	drivers/ata/libata-scsi.c
	include/linux/libata.h

Futher merge of Linus's head and compilation fixups.

Signed-Off-By: David Howells <dhowells@redhat.com>
2006-12-05 17:01:28 +00:00
David Howells 4c1ac1b491 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6
Conflicts:

	drivers/infiniband/core/iwcm.c
	drivers/net/chelsio/cxgb2.c
	drivers/net/wireless/bcm43xx/bcm43xx_main.c
	drivers/net/wireless/prism54/islpci_eth.c
	drivers/usb/core/hub.h
	drivers/usb/input/hid-core.c
	net/core/netpoll.c

Fix up merge failures with Linus's head and fix new compilation failures.

Signed-Off-By: David Howells <dhowells@redhat.com>
2006-12-05 14:37:56 +00:00
Paul Mackerras 79acbb3ff2 Merge branch 'linux-2.6' into for-linus 2006-12-04 15:59:07 +11:00
Andy Fleming e8a2b6a420 [PATCH] PHY: Add support for configuring the PHY connection interface
Most PHYs connect to an ethernet controller over a GMII or MII
interface.  However, a growing number are connected over
different interfaces, such as RGMII or SGMII.

The ethernet driver will tell the PHY what type of connection it
is by setting it manually, or passing it in through phy_connect
(or phy_attach).

Changes include:
* Updates to documentation
* Updates to PHY Lib consumers
* Changes to PHY Lib to add interface support
* Some minor changes to whitespace in phy.h
* gianfar driver now detects interface and passes appropriate
  value to PHY Lib
Signed-off-by: Andrew Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-12-02 00:33:11 -05:00
Jeff Garzik cefd9f7f12 Revert "[PATCH] Add support for Marvell 88e1111S and 88e1145"
This reverts commit 477c517903d57047150b01608149e02c6e9d83dd.

This patch depended on something that was not yet committed.
2006-12-02 00:12:04 -05:00