From Meteorlake, Latency Level, SAGV bloack time are read from
LATENCY_SAGV register instead of the GT driver pcode mailbox. DDR type
and QGV information are also to be read from Mem SS registers.
v2:
- Simplify MTL_MEM_SS_INFO_QGV_POINT macro(MattR)
- Nit: Rearrange the bit def's from higher to lower(MattR)
- Restore platform definition for ADL-P(MattR)
- Move back intel_qgv_point def to intel_bw.c(Jani)
v3:
- Rebase
Bspec: 64636, 64608
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Original Author: Caz Yokoyama
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220902060342.151824-9-radhakrishna.sripada@intel.com
On MTL TypeC ports the AUX_CH_CTL and AUX_CH_DATA addresses have
changed wrt. previous platforms, adjust the code accordingly.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220902060342.151824-8-radhakrishna.sripada@intel.com
Add support for display power wells on MTL. The differences from XE_LPD:
- The AUX HW block is moved to the PICA block, where the registers are on
an always-on power well and the functionality needs to be powered on/off
via the AUX_CH_CTL register: [1], [2]
- The DDI IO power on/off programming sequence is moved to the PHY PLL
enable/disable sequence. [3], [4], [5]
Bspec: [1] 49233, [2] 65247, [3] 64568, [4] 65451, [5] 65450
v2:
- Update the comment in aux power well enable
- Reuse the noop sync fn for aux sync.
- Use REG_BIT for new register bit definitions
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220902060342.151824-7-radhakrishna.sripada@intel.com
Add tables to map the GMBUS pin pairs to GPIO registers and port to DDC.
From spec we have registers GPIO_CTL[1-5] mapped to native display phys and
GPIO_CTL[9-12] are mapped to TC ports.
v2:
- Drop unused GPIO pins(MattR)
BSpec: 49306
Cc: Matt Roper <matthew.d.roper@intel.com>
Original Author: Brian J Lovin
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Reviewed-by: Balasubramani Vivekanandan <balasubramani.vivekanandan@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220902060342.151824-6-radhakrishna.sripada@intel.com
Future platforms can read the IP version from a register and the
IP version numbers need not be hard coded in device info. Move the
ip version for media and display to runtime info.
On platforms where hard coding of IP version is required, update
the IP version in __runtime under device_info.
v2:
- Avoid name collision for ip versions(Jani)
v4.1:
- Fix build error in mock_gem_device.c
v4.2:
- Use ip instead of version for ip_vesion member.(MattR)
Suggested-by: Jani Nikula <jani.nikula@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220902221054.173524-1-radhakrishna.sripada@intel.com
Replace vkms_formats macro for fixed-point operations with functions
from drm/drm_fixed.h to do the same job and fix 32-bit compilation
errors.
v2:
- don't cast results to s32 (Igor)
- add missing drm_fixp2int conversion (Igor)
Fixes: a19c2ac9858 ("drm: vkms: Add support to the RGB565 format")
Tested-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> (v1)
Reviewed-by: Alex Deucher <alexander.deucher@amd.com> (v1)
Reported-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220910190303.682897-1-mwen@igalia.com
drm-misc-next for v6.1-rc1:
[airlied - fix sun4i_tv build]
UAPI Changes:
- Hide unregistered connectors from GETCONNECTOR ioctl.
- drm/virtio no longer advertises LINEAR modifier, as it doesn't work.
-
Cross-subsystem Changes:
- Fix GPF in udmabuf failure path.
Core Changes:
- Rework TTM placement to use intersect/compatible functions.
- Drop legacy DP-MST support.
- More DP-MST related fixes, and move all state into atomic.
- Make DRM_MIPI_DBI select DRM_KMS_HELPER.
- Add audio_infoframe packing for DP.
- Add logging when some atomic check functions fail.
- Assorted documentation updates and fixes.
Driver Changes:
- Assorted cleanups and fixes in msm, lcdif, nouveau, virtio,
panel/ilitek, bridge/icn6211, tve200, gma500, bridge/*, panfrost, via,
bochs, qxl, sun4i.
- Add add AUO B133UAN02.1, IVO M133NW4J-R3, Innolux N120ACA-EA1 eDP panels.
- Improve DP-MST modeset state handling in amdgpu, nouveau, i915.
- Drop DP-MST from radeon driver, it was broken and only user of legacy
DP-MST.
- Handle unplugging better in vc4.
- Simplify drm cmdparser tests.
- Add DP support to ti-sn65dsi86.
- Add MT8195 DP support to mediatek.
- Support RGB565, XRGB64, and ARGB64 formats in vkms.
- Convert sun4i tv support to atomic.
- Refactor vc4/vec TV Modesetting, and fix timings.
- Use atomic helpers instead of simple display helpers in ssd130x.
Maintainer changes:
- Add Douglas Anderson as reviewer for panel-edp.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/a489485b-3ebc-c734-0f80-aed963d89efe@linux.intel.com
Pull all the skl+ watermark code (and the dbuf/sagv/ipc code
since it's all sort of intertwined and I'm too lazy to think
of a finer grained split right now) into its own file from the
catch-all intel_pm.c.
Also sneak in the s/dev_priv/i915/ rename while at it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220908191646.20239-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
No reaon to have this humongous if ladder in intel_read_wm_latency().
Just split it into nicer per-platforms functions.
Also do the s/dev_priv/i915/ while touching all of this code.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220908191646.20239-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
This panel has the same delay timing as N116BCA-EA1 from the same
company, which is also the same as delay_200_500_e80_d50.
Add an entry for it.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220908085454.1024167-2-wenst@chromium.org
On BDW+ M/N are double buffered and so we can easily reprogram them
during a fastset. So for eDP panels that support seamless DRRS we
can just change these without a full modeset.
For earlier platforms we'd need to play tricks with M1/N1 vs.
M2/N2 during the fastset to make sure we do the switch atomically.
Not sure the added complexity is worth the hassle, so leave it
alone for now.
The slight downside is that we have to keep the link running at
a link rate capable of supporting the highest refresh rate we
want to use. For the moment we just pick the highest mode the
panel reports and calculate the link based on that. This might
need further refinement (eg. if we run into bandwidth
restrictions)...
v2: Only use the high link rate if the platform really supports
the seamless M/N change uring fastset (ie. bdw+)
v3: Rebase due to HAS_DOUBLE_BUFFERED_M_N()
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220907091057.11572-16-ville.syrjala@linux.intel.com
Add a function to get the fixed_mode with the highest clock.
The plan is to use this for the link bw calculation on seamless
DRRS panels so that we alwasy end up with the same link params
regardless of the requested refresh rate. This will allow fastset
to do seamless refresh rate changes based on userspace request
instead of having to go for a full modeset.
TODO: the function name isn't great
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220907091057.11572-15-ville.syrjala@linux.intel.com
To make the fastboot checks at least somewhat sensible let's mark
the expected DPLL as the active one right after we finished the
state computation. Otherwise intel_pipe_config_compare() will
always be comparing things against NULL/0.
TODO: This is still not really right. If the previous commit
had to fall back to the other PLL then the comparisong will
now fail. I guess intel_pipe_config_compare() should rather
be comparing port_dplls[] instead. But to do that we really
should just unify every platform to use the port_dplls[]
approach whether they have any need for PLL fallbacks or not.
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220907091057.11572-12-ville.syrjala@linux.intel.com
Now that we no longer fuzz M/N during fastset these should
match exctly.
In order to get a match with what the BIOS does we need to round
M/N down. And we do the opposite rounding when doing the readback.
That gets us pretty much the same thing back.
There can still be slight rounding differences between FDI M/N
vs. the DPLL output so we allow for tiny deviation in
intel_pipe_config_sanity_check().
v2: Tweak rounding/sanity check stuff a bit
Reviewed-by: Jani Nikula <jani.nikula@intel.com> #v1
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220907091057.11572-10-ville.syrjala@linux.intel.com
Do the DPLL computation before fastset checks. This should
allow us to get rid of all that horrible fuzzy clock handling
for fastsets. Who knows how many bugs there are caused by our
state not actually matching what the hardware will generate.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220907091057.11572-9-ville.syrjala@linux.intel.com
Fill port_clock and hw.adjusted_mode.crtc_clock with the actual
frequency we're going to be getting from the hardware. This will
let us accurately compute all derived state that depends on those.
v2: Reintroduce iCLKIP WARN
v3: Try to deal with VLV/BXT DSI PLL as well
Reviewed-by: Jani Nikula <jani.nikula@intel.com> #v1
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220907091057.11572-8-ville.syrjala@linux.intel.com
Only reassign the pipe's DPLL if it's going through a full
.compute_config() cycle. If OTOH it's just getting modeset
eg. in order to change cdclk there doesn't seem much point in
picking a new DPLL for it.
This should also prevent .get_dplls() from seeing a funky port_clock
for DP even in cases where the readout produces a non-standard
clock and we (for some reason) have decided to not fully recompute
the state to remedy the situation.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220907091057.11572-7-ville.syrjala@linux.intel.com
Currently we calculate a lot of things (pixel rate, watermarks,
cdclk) trusting that the DPLL can generate the exact frequency
we ask it. In practice that is not true and there can be
certain amount of rounding involved.
To allow us to eventually get accurate numbers for all our
DPLL clock derived state we need to move the DPLL calculation
to hapen much earlier. To that end we hoist it up to the just
after the fastset checks. For now we just do the easy code
motion, and the actual back feeding of the final DPLL clock
into the state will come later.
A slight change here is that now .crtc_compute_clock()
can get called while the shared_dpll is still assigned.
But since .crtc_compute_clock() no longer assignes new
shared_dplls this is perfectly fine.
TODO: I'd actually like to do this before the fastset check
so that if the DPLL state should change we actually do the
modeset. Which I think is what the video aficionados want,
but it might not be what the fans of fastboot want. Not yet
sure how to reconcile those conflicting requirements...
v2: s/return/goto/ in error handling
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220907091057.11572-6-ville.syrjala@linux.intel.com
The simple display pipeline is a set of helpers that can be used by DRM
drivers to avoid dealing with all the needed components and just define
a few functions to operate a simple display device with one full-screen
scanout buffer feeding a single output.
But it is arguable that this provides the correct level of abstraction
for simple drivers, and recently some have been ported from using these
simple display helpers to use the regular atomic helpers instead.
The rationale for this is that the simple display pipeline helpers don't
hide that much of the DRM complexity, while adding an indirection layer
that conflates the concepts of CRTCs and planes. This makes the helpers
less flexible and harder to be reused among different graphics drivers.
Also, for simple drivers, using the full atomic helpers doesn't require
a lot of additional code. So adding a simple display pipeline layer may
not be worth it.
For these reasons, let's follow that trend and make ssd130x a plain DRM
driver that creates its own primary plane, CRTC, enconder and connector.
Suggested-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220905222759.2597186-1-javierm@redhat.com
Currently, pic_height of vdsc_cfg structure is being used to calculate
slice_height, before it is set for DP.
So taking out the lines to set pic_height from the helper
intel_dp_dsc_compute_params() to individual encoders, and setting
pic_height, before it is used to calculate slice_height for DP.
Fixes: 5a6d866f8e ("drm/i915: Get slice height before computing rc params")
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220902103219.1168781-1-ankit.k.nautiyal@intel.com
We have a couple of places that want to make distinction between
double buffered M/N registers vs. the split M1/N1+M2/N2 registers.
Add a helper for that.
v2: Turn into a HAS_ macro (Jani)
Reviewed-by: Jani Nikula <jani.nikula@intel.com> #v1
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220907091057.11572-4-ville.syrjala@linux.intel.com
Details:
Currently, when trying to suspend and resume with qxl device，
there are some error messages after resuming,
eventually caused to black screen and can't be recovered.
The first error message:
[ 64.668577][ C3] [drm] driver is in bug mode
This error is due to guest qxl driver
will call qxl_reinit_memslots(qdev) during system resume,
but didn't call qxl_io_reset(qdev) before this,
Then will cause the QXL_IO_MEMSLOT_ADD operation to fail on QEMU,
qxl->guest_bug flag will be set，As a result,
the QXL device can't communicate with guest qxl driver through the IO port.
after fix the first error,can success to resume and login to desktop,
but shortly after that will observe the second error message :
[ 353.095343][ T863] qxl 0000:00:02.0: object_init failed for (262144, 0x00000001)
[ 353.096660][ T863] [drm:qxl_gem_object_create [qxl]] *ERROR* Failed to allocate GEM object (260852, 1, 4096, -12)
[ 353.097277][ T863] [drm:qxl_alloc_ioctl [qxl]] *ERROR* qxl_alloc_ioctl: failed to create gem ret=-12
[ 368.197538][ T863] qxl 0000:00:02.0: object_init failed for (3149824, 0x00000001)
[ 368.197541][ T863] [drm:qxl_alloc_bo_reserved [qxl]] *ERROR* failed to allocate VRAM BO
The problem is caused by calling qxl_ring_init_hdr(qdev->release_ring)
in qxl_drm_resume() function.
When do QXL_IO_RESET,QEMU will call init_qxl_ram(),
so params like prod,cons,notify_on_cons and notify_on_prod
will be set to default value.
Ring push/pop actions for release_ring can be performed normally.
But call qxl_ring_init_hdr(qdev->release_ring)
will eventually set notify_on_prod to number of QXL_RELEASE_RING_SIZE,
affect the value of notify in qxl_push_free_res() function always be false,
QEMU will no longer send events of QXL_INTERRUPT_DISPLAY to the
guest qxl driver，so qxl_ring_pop() will never been called anymore，
and can't do dma_fence_signal(),result to ttm_bo_wait_ctx(bo, ctx)
always return EBUSY,fail to call qxl_bo_create().
Test scenario:
1) start virtual machine with qemu command "-device qxl-vga"
2) click suspend botton to enter suspend mode
3) resume and observe the error message in kernel logs,screen will be black
Let's fix this by reset io and remove the qxl_ring_init_hdr calling.
Signed-off-by: Zongmin Zhou<zhouzongmin@kylinos.cn>
Suggested-by: Ming Xie<xieming@kylinos.cn>
Link: http://patchwork.freedesktop.org/patch/msgid/20220907094423.93581-1-min_halo@163.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
VGA_IS1_RC is the color mode register (VGA_IS1_RM the one for monochrome
mode, note C vs. M at the end). So when using VGA_IS1_RC make sure the
vga device is actually in color mode and set the corresponding bit in the
misc register.
Reproducible when booting VMs in UEFI mode with some edk2 versions (edk2
fix is on the way too). Doesn't happen in BIOS mode because in that
case the vgabios already flips the bit.
Fixes: 250e743915 ("drm/bochs: Add screen blanking support")
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: http://patchwork.freedesktop.org/patch/msgid/20220906142957.2763577-1-kraxel@redhat.com
Without this, the drm core advertises LINEAR modifier which is
incorrect.
Also userspace virgl does not support modifiers. For example, it causes
chrome on ozone/drm to fail with "Failed to create scanout buffer".
Fixes: 2af104290d ("drm: introduce fb_modifiers_not_supported flag in mode_config")
Suggested-by: Shao-Chuan Lee <shaochuan@chromium.org>
Signed-off-by: Chia-I Wu <olvaffe@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20220831190601.1295129-1-olvaffe@gmail.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The other error labels in sun4i_tv_bind() are named after the task they
perform (err_disable_clk to call clk_disable_unprepare for example).
However, the err_cleanup_connector is named after the calling site
(drm_connector_init failing) and will actually cleanup the encoder. Let's
rename it to err_cleanup_encoder to be consistent.
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220728-rpi-analog-tv-properties-v2-39-459522d653a7@cerno.tech
This commit fixes vertical timings of the VEC (composite output) modes
to accurately represent the 525-line ("NTSC") and 625-line ("PAL") ITU-R
standards.
Previous timings were actually defined as 502 and 601 lines, resulting
in non-standard 62.69 Hz and 52 Hz signals being generated,
respectively.
Signed-off-by: Mateusz Kwiatkowski <kfyatek+publicgit@gmail.com>
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220728-rpi-analog-tv-properties-v2-28-459522d653a7@cerno.tech
Change the mode_set function pointer logic to declarative config0,
config1 and custom_freq fields, to make TV mode setting logic more
concise and uniform.
Signed-off-by: Mateusz Kwiatkowski <kfyatek+publicgit@gmail.com>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
[Maxime: Fixed != 0 check, added tv_mode variable]
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220728-rpi-analog-tv-properties-v2-26-459522d653a7@cerno.tech
The variable ret is assigned in the judgment branch statement, he does
not need to initialize the assignment.
Signed-off-by: Li zeming <zeming@nfschina.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220907032934.4490-1-zeming@nfschina.com
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Radhakrishna Sripada