As said in rfc7829, section 3, point 12:
The SCTP stack SHOULD expose the PF state of its destination
addresses to the ULP as well as provide the means to notify the
ULP of state transitions of its destination addresses from
active to PF, and vice versa. However, it is recommended that
an SCTP stack implementing SCTP-PF also allows for the ULP to be
kept ignorant of the PF state of its destinations and the
associated state transitions, thus allowing for retention of the
simpler state transition model of [RFC4960] in the ULP.
Not only does it allow to expose the PF state to ULP, but also
allow to ignore sctp-pf to ULP.
So this patch is to add pf_expose per netns, sock and asoc. And in
sctp_assoc_control_transport(), ulp_notify will be set to false if
asoc->expose is not 'enabled' in next patch.
It also allows a user to change pf_expose per netns by sysctl, and
pf_expose per sock and asoc will be initialized with it.
Note that pf_expose also works for SCTP_GET_PEER_ADDR_INFO sockopt,
to not allow a user to query the state of a sctp-pf peer address
when pf_expose is 'disabled', as said in section 7.3.
v1->v2:
- Fix a build warning noticed by Nathan Chancellor.
v2->v3:
- set pf_expose to UNUSED by default to keep compatible with old
applications.
v3->v4:
- add a new entry for pf_expose on ip-sysctl.txt, as Marcelo suggested.
- change this patch to 1/5, and move sctp_assoc_control_transport
change into 2/5, as Marcelo suggested.
- use SCTP_PF_EXPOSE_UNSET instead of SCTP_PF_EXPOSE_UNUSED, and
set SCTP_PF_EXPOSE_UNSET to 0 in enum, as Marcelo suggested.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a race between driver code that does setup/cleanup of device
and devlink reload operation that in some drivers works with the same
code. Use after free could we easily obtained by running:
while true; do
echo 10 > /sys/bus/netdevsim/new_device
devlink dev reload netdevsim/netdevsim10 &
echo 10 > /sys/bus/netdevsim/del_device
done
Fix this by enabling reload only after setup of device is complete and
disabling it at the beginning of the cleanup process.
Reported-by: Ido Schimmel <idosch@mellanox.com>
Fixes: 2d8dc5bbf4 ("devlink: Add support for reload")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a simple test for recently added netdevice alternative names.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tuong Lien says:
====================
TIPC Encryption
This series provides TIPC encryption feature, kernel part. There will be
another one in the 'iproute2/tipc' for user space to set key.
v2: add select crypto 'aes(gcm)' for TIPC_CRYPTO in Kconfig
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds two netlink commands to TIPC in order for user to be
able to set or remove AEAD keys:
- TIPC_NL_KEY_SET
- TIPC_NL_KEY_FLUSH
When the 'KEY_SET' is given along with the key data, the key will be
initiated and attached to TIPC crypto. On the other hand, the
'KEY_FLUSH' command will remove all existing keys if any.
Acked-by: Ying Xue <ying.xue@windreiver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit offers an option to encrypt and authenticate all messaging,
including the neighbor discovery messages. The currently most advanced
algorithm supported is the AEAD AES-GCM (like IPSec or TLS). All
encryption/decryption is done at the bearer layer, just before leaving
or after entering TIPC.
Supported features:
- Encryption & authentication of all TIPC messages (header + data);
- Two symmetric-key modes: Cluster and Per-node;
- Automatic key switching;
- Key-expired revoking (sequence number wrapped);
- Lock-free encryption/decryption (RCU);
- Asynchronous crypto, Intel AES-NI supported;
- Multiple cipher transforms;
- Logs & statistics;
Two key modes:
- Cluster key mode: One single key is used for both TX & RX in all
nodes in the cluster.
- Per-node key mode: Each nodes in the cluster has one specific TX key.
For RX, a node requires its peers' TX key to be able to decrypt the
messages from those peers.
Key setting from user-space is performed via netlink by a user program
(e.g. the iproute2 'tipc' tool).
Internal key state machine:
Attach Align(RX)
+-+ +-+
| V | V
+---------+ Attach +---------+
| IDLE |---------------->| PENDING |(user = 0)
+---------+ +---------+
A A Switch| A
| | | |
| | Free(switch/revoked) | |
(Free)| +----------------------+ | |Timeout
| (TX) | | |(RX)
| | | |
| | v |
+---------+ Switch +---------+
| PASSIVE |<----------------| ACTIVE |
+---------+ (RX) +---------+
(user = 1) (user >= 1)
The number of TFMs is 10 by default and can be changed via the procfs
'net/tipc/max_tfms'. At this moment, as for simplicity, this file is
also used to print the crypto statistics at runtime:
echo 0xfff1 > /proc/sys/net/tipc/max_tfms
The patch defines a new TIPC version (v7) for the encryption message (-
backward compatibility as well). The message is basically encapsulated
as follows:
+----------------------------------------------------------+
| TIPCv7 encryption | Original TIPCv2 | Authentication |
| header | packet (encrypted) | Tag |
+----------------------------------------------------------+
The throughput is about ~40% for small messages (compared with non-
encryption) and ~9% for large messages. With the support from hardware
crypto i.e. the Intel AES-NI CPU instructions, the throughput increases
upto ~85% for small messages and ~55% for large messages.
By default, the new feature is inactive (i.e. no encryption) until user
sets a key for TIPC. There is however also a new option - "TIPC_CRYPTO"
in the kernel configuration to enable/disable the new code when needed.
MAINTAINERS | add two new files 'crypto.h' & 'crypto.c' in tipc
Acked-by: Ying Xue <ying.xue@windreiver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new structure 'tipc_aead_key' is added to the 'tipc.h' for user to
be able to transfer a key to TIPC in kernel. Netlink will be used for
this purpose in the later commits.
Acked-by: Ying Xue <ying.xue@windreiver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When user sets RX key for a peer not existing on the own node, a new
node entry is needed to which the RX key will be attached. However,
since the peer node address (& capabilities) is unknown at that moment,
only the node-ID is provided, this commit allows the creation of a node
with only the data that we call as “preliminary”.
A preliminary node is not the object of the “tipc_node_find()” but the
“tipc_node_find_by_id()”. Once the first message i.e. LINK_CONFIG comes
from that peer, and is successfully decrypted by the own node, the
actual peer node data will be properly updated and the node will
function as usual.
In addition, the node timer always starts when a node object is created
so if a preliminary node is not used, it will be cleaned up.
The later encryption functions will also use the node timer and be able
to create a preliminary node automatically when needed.
Acked-by: Ying Xue <ying.xue@windreiver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a need to support the crypto asynchronous operations in the later
commits, apart from the current RCU mechanism for bearer pointer, we
add a 'refcnt' to the bearer object as well.
So, a bearer can be hold via 'tipc_bearer_hold()' without being freed
even though the bearer or interface can be disabled in the meanwhile.
If that happens, the bearer will be released then when the crypto
operation is completed and 'tipc_bearer_put()' is called.
Acked-by: Ying Xue <ying.xue@windreiver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2019-11-08
Another series that contains updates to the ice driver only.
Anirudh cleans up the code of kernel config of ifdef wrappers by moving
code that is needed by DCB to disable and enable the PF VSI for
configuration. Implements ice_vsi_type_str() to convert an VSI type
enum value to its string equivalent to help identify VSI types from
module print statements.
Usha and Tarun add support for setting the maximum per-queue bit rate
for transmit queues.
Dave implements dcb_nl set functions and supporting software DCB
functions to support the callbacks defined in the dcbnl_rtnl_ops
structure.
Henry adds a check to ensure we are not resetting the device when trying
to configure it, and to return -EBUSY during a reset.
Usha fixes a call trace caused by the receive/transmit descriptor size
change request via ethtool when DCB is configured by using the number of
enabled queues and not the total number of allocated queues.
Paul cleans up and refactors the software LLDP configuration to handle
when firmware DCBX is disabled.
Akeem adds checks to ensure the VF or PF is not disabled before honoring
mailbox messages to configure the VF.
Brett corrects the check to make sure the vector_id passed down from
iavf is less than the max allowed interrupts per VF. Updates a flag bit
to align with the current specification.
Bruce updates a switch statement to use the correct status of the
Download Package AQ command. Does some housekeeping by cleaning up a
conditional check that is not needed.
Mitch shortens up the delay for SQ responses to resolve issues with VF
resets failing.
Jake cleans up the code reducing namespace pollution and to simplify
ice_debug_cq() since it always uses the same mask, not need to pass it
in. Improve debugging by adding the command opcode in the debug
messages that print an error code.
v2: fixed reverse christmas tree issue in patch 3 of the series.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
To help aid in debugging, display the command opcode in debug messages
that print an error code. This makes it easier to see what command
failed if only ICE_DBG_AQ_MSG is enabled.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ice_debug_cq is passed a mask which is always ICE_DBG_AQ_CMD. Modify this
function, removing the mask parameter entirely, and directly use the more
appropriate ICE_DBG_AQ_DESC and ICE_DBG_AQ_DESC_BUF.
The function is only called from ice_controlq.c, and has no
other callers outside of that file. Move it and mark it static to avoid
namespace pollution.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ice_vsi_type_str converts an ice_vsi_type enum value to its string
equivalent. This is expected to help easily identify VSI types from
module print statements.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is no reason to do this conditional check before the assignment so
simply remove it.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the VLAN ice_flg64_bits are off by 1. Fix this by
setting the ICE_FLG_EVLAN_x8100 flag to 14, which also updates
ICE_FLG_EVLAN_x9100 to 15 and ICE_FLG_VLAN_x8100 to 16.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Shorten the delay for SQ responses, but increase the number of loops.
Max delay time is unchanged, but some operations complete much more
quickly.
In the process, add a new define to make the delay count and delay time
more explicit. Add comments to make things more explicit.
This fixes a problem with VF resets failing on with many VFs.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since the return value from the Download Package AQ command is stored in
hw->pkg_dwnld_status, use that instead of sq_last_status since that may
have the return value from some other AQ command leading to unexpected
results.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently we check to make sure the vector_id passed down from iavf
is less than or equal to pf->hw.func_caps.common_caps.num_msix_vectors.
This is incorrect because the vector_id is always 0-based and never
greater than or equal to the ICE_MAX_INTR_PER_VF. Fix this by checking
to make sure the vector_id is less than the max allowed interrupts per
VF (ICE_MAX_INTR_PER_VF).
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds code to check if PF or VF is disabled before honoring
mailbox message to configure VF - If it is disabled, and opcode is for
resetting VF, the PF driver simply tell VF that all is set. In addition,
if reset is ongoing, and Admin intend to configure VF on the host, we can
poll the VF enabling bit to make sure it is ready before continue - If
after ~250 milliseconds, VF is not in active state, we can bail out with
invalid error.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move software LLDP configuration when FW DCBX is disabled to
ice_init_pf_dcb, since that is where the FW DCBX state is determined.
Remove this software LLDP configuration from ice_vsi_setup and
ice_set_priv_flags. Software configuration includes redirecting Rx LLDP
packets up the stack, when FW DCBX is not running.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the call trace caused by the kernel when the Rx/Tx
descriptor size change request is initiated via ethtool when DCB is
configured. ice_set_ringparam() should use vsi->num_txq instead of
vsi->alloc_txq as it represents the queues that are enabled in the
driver when DCB is enabled/disabled. Otherwise, queue index being
used can go out of range.
For example, when vsi->alloc_txq has 104 queues and with 3 TCS enabled
via DCB, each TC gets 34 queues, vsi->num_txq will be 102 and only 102
queues will be enabled.
Signed-off-by: Usha Ketineni <usha.k.ketineni@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Certain subsystems behave very badly when called during reset (core
dump). This patch returns -EBUSY when reconfiguring some subsystems
during reset. With this patch some ethtool functions will not core
dump during reset.
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Implement interface layer for the DCBNL subsystem. These are the functions
to support the callbacks defined in the dcbnl_rtnl_ops struct. These
callbacks are going to be used to interface with the DCB settings of the
device. Implementation of dcb_nl set functions and supporting SW DCB
functions.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Allow for rate limiting Tx queues. Bitrate is set in
Mbps(megabits per second).
Mbps max-rate is set for the queue via sysfs:
/sys/class/net/<iface>/queues/tx-<queue>/tx_maxrate
ex: echo 100 >/sys/class/net/ens7/queues/tx-0/tx_maxrate
echo 200 >/sys/class/net/ens7/queues/tx-1/tx_maxrate
Note: A value of zero for tx_maxrate means disabled,
default is disabled.
Signed-off-by: Usha Ketineni <usha.k.ketineni@intel.com>
Co-developed-by: Tarun Singh <tarun.k.singh@intel.com>
Signed-off-by: Tarun Singh <tarun.k.singh@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
DCB configuration flow needs to disable and enable only the PF (main)
VSI, so use ice_ena_vsi and ice_dis_vsi. To avoid the use of ifdef to
control the staticness of these functions, move them to ice_lib.c.
Also replace the allocate and copy of old_cfg to kmemdup() in
ice_pf_dcb_cfg().
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix following compile error on i386 architecture.
ERROR: "__udivdi3" [drivers/net/ethernet/chelsio/cxgb4/cxgb4.ko] undefined!
Fixes: 0e395b3cb1 ("cxgb4: add FLOWC based QoS offload")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* typo fixes in docs
* APIs for station separation using VLAN tags rather
than separate wifi netdevs
* some preparations for upcoming features (802.3 offload
and airtime queue limits (AQL)
* stack reduction in ieee80211_assoc_success()
* use DEFINE_DEBUGFS_ATTRIBUTE in hwsim
-----BEGIN PGP SIGNATURE-----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=gDUI
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2019-11-08' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Some relatively small changes:
* typo fixes in docs
* APIs for station separation using VLAN tags rather
than separate wifi netdevs
* some preparations for upcoming features (802.3 offload
and airtime queue limits (AQL)
* stack reduction in ieee80211_assoc_success()
* use DEFINE_DEBUGFS_ATTRIBUTE in hwsim
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
match_string() returns the array index of a matching string.
Use it instead of the open-coded implementation.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add optional support for syscfg clock in dwmac-stm32.c
Now Syscfg clock is activated automatically when syscfg
registers are used
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This provides an alternative mechanism for AP VLAN support where a
single netdev is used with VLAN tagged frames instead of separate
netdevs for each VLAN without tagged frames from the WLAN driver.
By setting NL80211_EXT_FEATURE_VLAN_OFFLOAD flag the driver indicates
support for a single netdev with VLAN tagged frames. Separate
VLAN-specific netdevs can be added using RTM_NEWLINK/IFLA_VLAN_ID
similarly to Ethernet. NL80211_CMD_NEW_KEY (for group keys),
NL80211_CMD_NEW_STATION, and NL80211_CMD_SET_STATION will optionally
specify vlan_id using NL80211_ATTR_VLAN_ID.
Signed-off-by: Gurumoorthi Gnanasambandhan <gguru@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20191031214640.5012-1-jouni@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To implement airtime queue limiting, we need to keep a running account of
the estimated airtime of all skbs queued into the device. Do to this
correctly, we need to store the airtime estimate into the skb so we can
decrease the outstanding balance when the skb is freed. This means that the
time estimate must be stored somewhere that will survive for the lifetime
of the skb.
To get this, decrease the size of the ack_frame_id field to 6 bits, and
lower the size of the ID space accordingly. This leaves 10 bits for use for
tx_time_est, which is enough to store a maximum of 4096 us, if we shift the
values so they become units of 4us.
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/157182474063.150713.16132669599100802716.stgit@toke.dk
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We've already parsed the same data in the caller, so we can
pass it. The only thing is that we might fill in more details
in ieee80211_assoc_success(), but that doesn't bother the
caller, so it's fine to do even when we share the parsed data.
This reduces the stack space usage of the call stack here,
Arnd reported it had grown above the 1024 byte warning limit.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20191028125240.cb7661671bd2.I757c8752bf4f2f35e54f5e0a2c0a9cd9216c3d8b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch moves the code handling SKBTX_WIFI_STATUS inside the TX path
into an extra function. This allows us to reuse it inside the 802.11 encap
offloading datapath.
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20191029091304.7330-2-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It is more clear to use DEFINE_DEBUGFS_ATTRIBUTE to define debugfs file
operation rather than DEFINE_SIMPLE_ATTRIBUTE.
It is detected with the help of coccinelle.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Link: https://lore.kernel.org/r/1572404462-45462-1-git-send-email-zhongjiang@huawei.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, we scan over all network namespaces at each received
discovery message in order to check if the sending peer might be
present in a host local namespaces.
This is unnecessary since we can assume that a peer will not change its
location during an established session.
We now improve the condition for this testing so that we don't perform
any redundant scans.
Fixes: f73b12812a ("tipc: improve throughput between nodes in netns")
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_peek_tail() can be used without protection of a lock,
as spotted by KCSAN [1]
In order to avoid load-stearing, add a READ_ONCE()
Note that the corresponding WRITE_ONCE() are already there.
[1]
BUG: KCSAN: data-race in sk_wait_data / skb_queue_tail
read to 0xffff8880b36a4118 of 8 bytes by task 20426 on cpu 1:
skb_peek_tail include/linux/skbuff.h:1784 [inline]
sk_wait_data+0x15b/0x250 net/core/sock.c:2477
kcm_wait_data+0x112/0x1f0 net/kcm/kcmsock.c:1103
kcm_recvmsg+0xac/0x320 net/kcm/kcmsock.c:1130
sock_recvmsg_nosec net/socket.c:871 [inline]
sock_recvmsg net/socket.c:889 [inline]
sock_recvmsg+0x92/0xb0 net/socket.c:885
___sys_recvmsg+0x1a0/0x3e0 net/socket.c:2480
do_recvmmsg+0x19a/0x5c0 net/socket.c:2601
__sys_recvmmsg+0x1ef/0x200 net/socket.c:2680
__do_sys_recvmmsg net/socket.c:2703 [inline]
__se_sys_recvmmsg net/socket.c:2696 [inline]
__x64_sys_recvmmsg+0x89/0xb0 net/socket.c:2696
do_syscall_64+0xcc/0x370 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x44/0xa9
write to 0xffff8880b36a4118 of 8 bytes by task 451 on cpu 0:
__skb_insert include/linux/skbuff.h:1852 [inline]
__skb_queue_before include/linux/skbuff.h:1958 [inline]
__skb_queue_tail include/linux/skbuff.h:1991 [inline]
skb_queue_tail+0x7e/0xc0 net/core/skbuff.c:3145
kcm_queue_rcv_skb+0x202/0x310 net/kcm/kcmsock.c:206
kcm_rcv_strparser+0x74/0x4b0 net/kcm/kcmsock.c:370
__strp_recv+0x348/0xf50 net/strparser/strparser.c:309
strp_recv+0x84/0xa0 net/strparser/strparser.c:343
tcp_read_sock+0x174/0x5c0 net/ipv4/tcp.c:1639
strp_read_sock+0xd4/0x140 net/strparser/strparser.c:366
do_strp_work net/strparser/strparser.c:414 [inline]
strp_work+0x9a/0xe0 net/strparser/strparser.c:423
process_one_work+0x3d4/0x890 kernel/workqueue.c:2269
worker_thread+0xa0/0x800 kernel/workqueue.c:2415
kthread+0x1d4/0x200 drivers/block/aoe/aoecmd.c:1253
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:352
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 451 Comm: kworker/u4:3 Not tainted 5.4.0-rc3+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: kstrp strp_work
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet says:
====================
net: introduce u64_stats_t
KCSAN found a data-race in per-cpu u64 stats accounting.
(The stack traces are included in the 8th patch :
tun: switch to u64_stats_t)
This patch series first consolidate code in five patches.
Then the last three patches address the data-race resolution.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to fix the data-race found by KCSAN, we
can use the new u64_stats_t type and its accessors instead
of plain u64 fields. This will still generate optimal code
for both 32 and 64 bit platforms.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to fix this data-race found by KCSAN [1],
switch to u64_stats_t helpers. They provide all
the needed annotations, without adding extra cost.
[1]
BUG: KCSAN: data-race in tun_get_user / tun_net_get_stats64
read to 0xffffe8ffffd8aca8 of 8 bytes by task 4882 on cpu 0:
tun_net_get_stats64+0x9b/0x230 drivers/net/tun.c:1171
dev_get_stats+0x89/0x1e0 net/core/dev.c:9103
rtnl_fill_stats+0x56/0x370 net/core/rtnetlink.c:1177
rtnl_fill_ifinfo+0xd3b/0x2100 net/core/rtnetlink.c:1667
rtmsg_ifinfo_build_skb+0xb0/0x150 net/core/rtnetlink.c:3472
rtmsg_ifinfo_event.part.0+0x4e/0xb0 net/core/rtnetlink.c:3504
rtmsg_ifinfo_event net/core/rtnetlink.c:3515 [inline]
rtmsg_ifinfo+0x85/0x90 net/core/rtnetlink.c:3513
__dev_notify_flags+0x18b/0x200 net/core/dev.c:7649
dev_change_flags+0xb8/0xe0 net/core/dev.c:7691
dev_ifsioc+0x201/0x6a0 net/core/dev_ioctl.c:237
dev_ioctl+0x149/0x660 net/core/dev_ioctl.c:489
sock_do_ioctl+0xdb/0x230 net/socket.c:1061
sock_ioctl+0x3a3/0x5e0 net/socket.c:1189
vfs_ioctl fs/ioctl.c:46 [inline]
file_ioctl fs/ioctl.c:509 [inline]
do_vfs_ioctl+0x991/0xc60 fs/ioctl.c:696
write to 0xffffe8ffffd8aca8 of 8 bytes by task 4883 on cpu 1:
tun_get_user+0x1d94/0x2ba0 drivers/net/tun.c:2002
tun_chr_write_iter+0x79/0xd0 drivers/net/tun.c:2022
call_write_iter include/linux/fs.h:1895 [inline]
new_sync_write+0x388/0x4a0 fs/read_write.c:483
__vfs_write+0xb1/0xc0 fs/read_write.c:496
__kernel_write+0xb8/0x240 fs/read_write.c:515
write_pipe_buf+0xb6/0xf0 fs/splice.c:794
splice_from_pipe_feed fs/splice.c:500 [inline]
__splice_from_pipe+0x248/0x480 fs/splice.c:624
splice_from_pipe+0xbb/0x100 fs/splice.c:659
default_file_splice_write+0x45/0x90 fs/splice.c:806
do_splice_from fs/splice.c:848 [inline]
direct_splice_actor+0xa0/0xc0 fs/splice.c:1020
splice_direct_to_actor+0x215/0x510 fs/splice.c:975
do_splice_direct+0x161/0x1e0 fs/splice.c:1063
do_sendfile+0x384/0x7f0 fs/read_write.c:1464
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 4883 Comm: syz-executor.1 Not tainted 5.4.0-rc3+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On 64bit arches, struct u64_stats_sync is empty and provides
no help against load/store tearing.
Using READ_ONCE()/WRITE_ONCE() would be needed.
But the update side would be slightly more expensive.
local64_t was defined so that we could use regular adds
in a manner which is atomic wrt IRQs.
However the u64_stats infra means we do not have to use
local64_t on 32bit arches since the syncp provides the needed
protection.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver can simply use the common infrastructure instead
of duplicating it.
This cleanup will ease u64_stats_t adoption in a single location.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This cleanup will ease u64_stats_t adoption in a single location.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This cleanup will ease u64_stats_t adoption in a single location.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many network drivers need it and hand-coded the same function.
In order to ease u64_stats_t adoption, it is time to factorize.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many network drivers use hand-coded implementation of the same thing,
let's factorize things so that u64_stats_t adoption is done once.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long