Since we currently do not support the offloading of 802.1D bridges, we
need to be able to let the device know it should not learn MAC addresses
on specific {Port, VID} pairs.
Add the SPVMLR register, which controls the learning enablement of
{Port, VID} pairs.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add SFDAT which is used to control switch ageing time.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order for a port to support {Port, VID} to FID mapping it needs to be
configured to a virtual port mode (as opposed to VLAN mode).
Add the SVPE register, which enables port virtualization.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An incoming packet can be classified into a filtering identifer (FID)
based on its VID or incoming port and VID ({Port, VID}).
Add the SVFA register, which controls this mapping.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Filtering identifiers (FIDs) are unique identifers of bridge instances
in the hardware.
Add the SFMR register, which is responsible for the creation and
configuration of these FIDs.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add definitions of SBPR, SBCM, SBPM, SBMM and PBMC registers that are
used to configure shared buffers.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add SPVID and SPVM registers responsible for default port VID
configuration and VLAN membership of a port.
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add SFN register which is used to poll for newly added and aged-out FDB
entries.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the SFD register which is responsible for filtering database
manipulation, including static and dynamic FDB entries.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing item helper which allows to access char bufs on multiple
offsets. This is needed by SFD and SFN register definitions.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets destined to offloaded netdevs will be classified to FIDs in the
device and flooded in case of BUM.
The flooding table used is of type FID-offset, which allows one to
create different flooding domains for different FIDs and specify the
offset in the flooding table for each FID (not necessarily equal to FID
or VID).
Add support for this flooding table type, by exposing the configuration
of the number of tables from this type and their size.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the newly introduced Spectrum switch ASIC, packets destined to not
offloaded netdevs will be classified to special FIDs (vFIDs) in the
device and flooded to the CPU port.
The flooding table used is of type per-FID, which allows one to create
different flooding domains for different vFIDs.
While using a simple single-entry flood table is certainly sufficient at
this point, we do plan to offload 802.1D bridges involving VLAN
interfaces, thus making this change necessary.
Add support for this flooding table type, by exposing the configuration
of the number of tables from this type and their size.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of the introduction of L2 offloads, allow different ports to
join/leave the flooding domain, according to user configuration.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This newly introduced netdevice notifier is called before actual change
upper happens. That provides a possibility for notifier handlers to
know upper change will happen and react to it, including possibility to
forbid the change. That is valuable for drivers which can check if the
upper device linkage is supported and forbid that in case it is not.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
timekeeping_init() can set the wall time offset, so we need to
increment the clock_was_set_seq counter. That way hrtimers will pick
up the early offset immediately. Otherwise on a machine which does not
set wall time later in the boot process the hrtimer offset is stale at
0 and wall time timers are going to expire with a delay of 45 years.
Fixes: 868a3e915f "hrtimer: Make offset update smarter"
Reported-and-tested-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Stefan Liebler <stli@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: John Stultz <john.stultz@linaro.org>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-10-16
This series contains updates to e1000, e1000e, igb, igbvf, ixgbe, ixgbevf,
i40e, i40evf and fm10k.
Alex Duyck fixes the polling routine for i40e/i40evf were the NAPI budget
for receive cleanup was being rounded up to 1 but the netpoll call was
expecting no Rx to be processed as the budget passed was 0. Also cleaned
up IN_NETPOLL flag that was not adding any value due to the receive
cleanup was handled in NAPI. Added support for netpoll for i40evf as
well.
Jesse updates all of our drivers to use napi_complete_done() instead of
napi_complete(), which allows us to use
/sys/class/net/ethX/gro_flush_timeout. Added ethtool support to control
and report the new Interrupt Limit register, since the XL710 hardware
has a different interrupt moderation design that can support a limit of
total interrupts per second per vector.
Shannon cleans up startup log entries to cut down the number by putting
a couple behind debug flags and combining others into single line. Added
support to enable/disable printing VEB statistics via ethtool.
Jingjing fixes a compile issue by adding const to functions that return
strings that are not going to be modified.
Greg Rose cleans up defines that were not used and were causing customer
confusion.
Greg Bowers adds support for setting a new bit in the Set Local LLDP MIB
admin queue command Type field.
Mitch fixes an issue where vlan_features field was set to the same value
as netdev features field, but before the features were actually being
set up, leaving the vlan_features empty. Resolve the issue by setting
up the netdev features first, then mask out the VLAN feature bits when
assigning vlan_features. Fixed VF init timing, where in some instances
the VFs would fail to initialize the first time you loaded the driver.
To correct this, increased the delay time for the init task and wait
longer before giving up.
v2: fix missing space in function header comment in patch 3, based on
feedback from Sergei Shtylyov.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
With 64 VFs, we can easily overwhelm the AQ on the PF if we have too low
a limit on the number of AQ requests. This leads to ARQ overflow errors,
and occasionally VFs that fail to initialize.
Since we really only hit this condition on initial VF driver load, the
requests that we process are lightweight, so this extra work doesn't
cause problems for the PF driver.
Change-ID: I620221520d8af987df6ace9ba938ffaf22107681
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On some devices, in some systems, in some configurations, the VFs would
fail to initialize the first time you loaded the driver.
To correct this, increase the delay time for the init task slightly, and
wait longer before giving up.
If we enable VFs and load the VF driver in the same kernel as the PF
driver, we can totally overwhelm the PF driver with AQ requests because
all of the instances try to initialize at the same time.
To help alleviate this, stagger the initial scheduling of the init task
using the PCIe function as a multiplier. We mask off the function to
only three bits so no instance has to wait too long.
With these two changes, initializing 128 VFs on a single device goes
from four minutes to just a few seconds.
Change-ID: If3d8720c1c4e838ab36d8781d9ec295a62380936
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
1000Base_T_Optical got added to the function that figures out what
is supported when link is down but not when link is up. Add it in there
too so that we display the correct information.
Change-ID: I85ebcdfa7c02d898c44c673b1500552a53c8042e
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The vlan_features field was correctly being set to the same value as the
netdev features field. However, this was being done before the features
were actually being set up, leaving the vlan_features empty.
Also, after a reset, vlan_features will be incorrectly assigned the
previous netdev feature flags, which can contain VLAN feature bits. This
makes the VLAN code angry and will cause a stack dump.
To fix these issues, set up the netdev features first, then mask out the
VLAN feature bits when assigning vlan_features.
Change-ID: Ib0548869dc83cf6a841cb8697dd94c12359ba4d2
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the number of invalid messages from a VF is exceeded, the VF
will be disabled, due to the invalid messages. This happens if
other VF drivers (like DPDK) send a message through the driver's
mailbox (aka virtchannel) interface, but the message is not
supported by the i40e pf driver, such as CONFIG_PROMISCUOUS_MODE.
This patch changes the num_invalid_msgs in struct i40e_vf to record
the continuous invalid msgs, and it will be reset when a valid msg
is received.
Change-ID: Iaec42fd3dcdd281476b3518be23261dd46fc3718
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The XL710 hardware has a different interrupt moderation design
that can support a limit of total interrupts per second per
vector, in addition to the "number of interrupts per second"
controls already established in the driver. This combination
of hardware features allows us to set very low default latency
settings but minimize the total CPU utilization by not
making too many interrupts, should the user desire.
The current driver implementation is still enabling the dynamic
moderation in the driver, and only using the rx/tx-usecs
limit in ethtool to limit the interrupt rate per second, by default.
The new code implemented in this patch
2) adds init/use of the new "Interrupt Limit" register
3) adds ethtool knob to control/report the limits above
Usage is ethtool -C ethx rx-usecs-high <value> Where <value> is number
of microseconds to create a rate of 1/N interrupts per second,
regardless of rx-usecs or tx-usecs values. Since there is a credit based
scheme in the hardware, the rx-usecs and tx-usecs can be configured for
very low latency for short bursts, but once the credit runs out the
refill rate on the credits is limited by rx-usecs-high.
Change-ID: I3a1075d3296123b0f4f50623c779b027af5b188d
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Adds support for setting a new bit in the Set Local LLDP MIB AQ command
Type field. When set to 1, the bit indicates to FW that Apps should be
treated as non-willing. When 0, FW behaves as before.
Change-ID: I0d2101c1606c59c7188d3e6a0c7810e0f205233a
Signed-off-by: Greg Bowers <gregory.j.bowers@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add an ethtool priv flag to enable and disable printing
the VEB statistics.
Change-ID: I7654054a3a73b08aa8310d94ee8fce6219107dd8
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Two defines that are not used are causing customer confusion - remove
them.
Change-ID: Icef0325aca8e0f4fcdfc519e026bdd375e791200
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Allow the nvmupdate application to decide when a read or write error
should be exposed to the user. Since the application needs to use
write probes to find the ReadOnly sections on a potentially unknown NVM
version in the HW and read probes to check the status of the last write,
some error messages are expected, but need not be shown to the users.
The driver doesn't know which are ignorable from real errors, so needs
to let the application make the decision.
Change-ID: I78fca8ab672bede11c10c820b83c26adfd536d03
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add const to functions that return strings that aren't going to be
modified. This addresses some reported compile complaints.
Change-ID: Ic56b1e814ab4d23a50480e7fdec652445f776ee8
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cut down on the number of startup log entries by putting a couple behind
debug flags and combining a couple others into a single line.
Change-ID: I708089f086308f84d43f8b6f0e8a634a02d058fb
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As per Eric Dumazet's previous patches:
(see commit (24d2e4a507) - tg3: use napi_complete_done())
Quoting verbatim:
Using napi_complete_done() instead of napi_complete() allows
us to use /sys/class/net/ethX/gro_flush_timeout
GRO layer can aggregate more packets if the flush is delayed a bit,
without having to set too big coalescing parameters that impact
latencies.
</end quote>
Tested
configuration: low latency via ethtool -C ethx adaptive-rx off
rx-usecs 10 adaptive-tx off tx-usecs 15
workload: streaming rx using netperf TCP_MAERTS
igb:
MIGRATED TCP MAERTS TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 10.0.0.1 () port 0 AF_INET : demo
...
Interim result: 941.48 10^6bits/s over 1.000 seconds ending at 1440193171.589
Alignment Offset Bytes Bytes Recvs Bytes Sends
Local Remote Local Remote Xfered Per Per
Recv Send Recv Send Recv (avg) Send (avg)
8 8 0 0 1176930056 1475.36 797726 16384.00 71905
MIGRATED TCP MAERTS TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 10.0.0.1 () port 0 AF_INET : demo
...
Interim result: 941.49 10^6bits/s over 0.997 seconds ending at 1440193142.763
Alignment Offset Bytes Bytes Recvs Bytes Sends
Local Remote Local Remote Xfered Per Per
Recv Send Recv Send Recv (avg) Send (avg)
8 8 0 0 1175182320 50476.00 23282 16384.00 71816
i40e:
Hard to test because the traffic is incoming so fast (24Gb/s) that GRO
always receives 87kB, even at the highest interrupt rate.
Other drivers were only compile tested.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The code in i40e and i40evf is using an "IN_NETPOLL" flag that has never
added any value due to the fact that the Rx clean-up is handled in NAPI.
As such the flag was set, the queue was scheduled via NAPI, and then polled
from the netpoll controller and if any Rx packets were processed the were
processed in the wrong context.
In addition the flag itself just added an unneeded conditional to the
hot-path so it can safely be dropped and save us a few instructions.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The polling routine for i40e was rounding up the budget for Rx cleanup to
1. This is incorrect as the netpoll poll call is expecting no Rx to be
processed as the budget passed was 0.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When we create a generic MSI domain, that MSI_FLAG_USE_DEF_CHIP_OPS
is set, and that any of .mask or .unmask are NULL in the irq_chip
structure, we set them to pci_msi_[un]mask_irq.
This is a bad idea for at least two reasons:
- PCI_MSI might not be selected, kernel fails to build (yes, this is
legitimate, at least on arm64!)
- This may not be a PCI/MSI domain at all (platform MSI, for example)
Either way, this looks wrong. Move the overriding of mask/unmask to
the PCI counterpart, and panic is any of these two methods is not
set in the core code (they really should be present).
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Link: http://lkml.kernel.org/r/1444760085-27857-1-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Because eth_type_trans() consumes ethernet header worth of bytes, a call
to read TCI from end of packet using rhine_rx_vlan_tag() no longer works
as it's reading from an invalid offset.
Tested to be working on PCEngines Alix board.
Fixes: 810f19bcb8 ("via-rhine: add consistent memory barrier in vlan receive code.")
Signed-off-by: Andrej Ota <andrej@ota.si>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, is only called from __prog_put_rcu in the bpf_prog_release
path. Need this to call this from bpf_prog_put also to get correct
accounting.
Fixes: aaac3ba95e ("bpf: charge user for creation of BPF maps and programs")
Signed-off-by: Tom Herbert <tom@herbertland.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet says:
====================
tcp/dccp: make our listener code more robust
This patch series addresses request sockets leaks and listener dismantle
phase. This survives a stress test with listeners being added/removed
quite randomly.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Under stress, a close() on a listener can trigger the
WARN_ON(sk->sk_ack_backlog) in inet_csk_listen_stop()
We need to test if listener is still active before queueing
a child in inet_csk_reqsk_queue_add()
Create a common inet_child_forget() helper, and use it
from inet_csk_reqsk_queue_add() and inet_csk_listen_stop()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let's reduce the confusion about inet_csk_reqsk_queue_drop() :
In many cases we also need to release reference on request socket,
so add a helper to do this, reducing code size and complexity.
Fixes: 4bdc3d6614 ("tcp/dccp: fix behavior of stale SYN_RECV request sockets")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit c69736696c.
At the time of above commit, tcp_req_err() and dccp_req_err()
were dead code, as SYN_RECV request sockets were not yet in ehash table.
Real bug was fixed later in a different commit.
We need to revert to not leak a refcount on request socket.
inet_csk_reqsk_queue_drop_and_put() will be added
in following commit to make clean inet_csk_reqsk_queue_drop()
does not release the reference owned by caller.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip6_blackhole_route() does not initialize the newly allocated
rt6_info properly. This patch:
1. Call rt6_info_init() to initialize rt6i_siblings and rt6i_uncached
2. The current rt->dst._metrics init code is incorrect:
- 'rt->dst._metrics = ort->dst._metris' is not always safe
- Not sure what dst_copy_metrics() is trying to do here
considering ip6_rt_blackhole_cow_metrics() always returns
NULL
Fix:
- Always do dst_copy_metrics()
- Replace ip6_rt_blackhole_cow_metrics() with
dst_cow_metrics_generic()
3. Mask out the RTF_PCPU bit from the newly allocated blackhole route.
This bug triggers an oops (reported by Phil Sutter) in rt6_get_cookie().
It is because RTF_PCPU is set while rt->dst.from is NULL.
Fixes: d52d3997f8 ("ipv6: Create percpu rt6_info")
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Reported-by: Phil Sutter <phil@nwl.cc>
Tested-by: Phil Sutter <phil@nwl.cc>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Julian Anastasov <ja@ssi.bg>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce rt6_info_init() to do the common init work for
'struct rt6_info' (after calling dst_alloc).
It is a prep work to fix the rt6_info init logic in the
ip6_blackhole_route().
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Julian Anastasov <ja@ssi.bg>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes sure that conn_params that were created just for
explicit_connect, will get properly deleted during cleanup.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
After clearing the params->explicit_connect variable the parameters
may need to be either added back to the right list or potentially left
absent from both the le_reports and the le_conns lists.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Devices undergoing an explicit connect should not have their
conn_params struct removed by the mgmt Remove Device command. This
patch fixes the necessary checks in the command handler to correct the
behavior.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We can't use hci_explicit_connect_lookup() since that would only cover
explicit connections, leaving normal reconnections completely
untouched. Not using it in turn means leaving out entries in
pend_le_reports.
To fix this and simplify the logic move conn params from the reports
list to the pend_le_conns list for the duration of an explicit
connect. Once the connect is complete move the params back to the
pend_le_reports list. This also means that the explicit connect lookup
function only needs to look into the pend_le_conns list.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Ido Schimmel