It is a rw_semaphore now and only write locked
while changing the clock. Also the lock is renamed
to better reflect what it is protecting.
v2: Keep the ttm_vm_ops on IGPs
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Move inter ring syncing with semaphores into the
existing ring allocations, with that we need to
lock the ring mutex only once.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
It is completely unnecessary to create fences
before they are emitted, so remove it and a bunch
of checks if fences are emitted or not.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
With the code in place, we can bind the driver, should make bisect possible.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Enable the on-chip messaging between the display engine and the GT.
v2: use bit definitions for DPFLIPSTAT reg
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And restructure the IRQ handling a little. We can use pipestat for most
things, and make sure we don't affect pipe events when enabling and
disabling vblank interupts.
We can leave vblank interrupts masked but enabled so we're not dependent
on the first client to toggle the disable timer. We can also mask all
render based interrupts, since the ring code will handle unmasking them
for us.
v2: roll in vblank masking, remove unneeded variable (Daniel)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since the offsets have all moved around.
v2: switch IS_DISPLAYREG and IS_VALLEYVIEW checks around since the latter is
cheaper (Daniel)
bail out early in IS_DISPLAYREG if the reg is in the new range (Daniel)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Fixup if cascading fail that broke HAS_FORCEWAKE machines.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- Use the correct union for getting the tiling info
- Properly init the PIPE_CONFIG field for SI
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Daniel Vetter writes:
rc2 is out the door so I've figured I'll annoy you with the first -next
pull request for 3.6 already. Highlights:
- new wait_rendring_timeout interface (Ben)
- l3 cache remapping and error uevent support (Ben)
- even more infoframes work from Paulo
- gen4 hotplug rework from Chris
- prep work to make Laurent Pincharts original mode constification for
connector->mode_fixup possible
QA reported a few new bugs this time around, but no regressions afact. For
3.5 the only thing I'm aware of is the edp vdd dmesg spam Linus originally
reported - it looks like that might have been introduced in 3.5. But
somehow my brain is routinely offline when I work on that issue, so things
seem to take forever (and atm I'm at patch v4 for that little problem).
* tag 'drm-intel-next-2012-06-04' of git://people.freedesktop.org/~danvet/drm-intel: (39 commits)
drm/i915: add min freq control to debugfs
drm/i915: don't chnage the original mode in dp_mode_fixup
drm/i915: adjusted_mode->clock in the dp mode_fixup
drm/i915: compute the target_clock for edp directly
drm/i915: extract object active state flushing code
drm/i915: clarify IBX dp workaround
drm/i915: simplify sysfs setup code
drm/i915: initialize the parity work only once
drm/i915: ivybridge_handle_parity_error should be static
drm/i915: l3 parity sysfs interface
drm/i915: remap l3 on hw init
drm/i915: enable parity error interrupts
drm/i915: Dynamic Parity Detection handling
drm/i915: s/mdelay/msleep/ in the sdvo detect function
drm/i915: reuse the sdvo tv clock adjustment in ilk mode_set
drm/i915: there's no cxsr on ilk
drm/i915: add some barriers when changing DIPs
drm/i915: remove comment about HSW HDMI DIPs
drm/i915: don't set SDVO_BORDER_ENABLE when we're HDMI
drm/i915: don't write 0 to DIP control at HDMI init
...
ValleyView is similar to IbexPeak here, but with different register
offsets.
v2: use SDVOB instead ov VLV_HDMIB (Daniel)
drop unnecessary eDP check in DP_C init (Daniel)
eDP support will be coming later from Shobit.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Might be able to merge this back in at some point, but we're seeing bugs
with ADPA based detection, so keep it separate for now with explicit
hotplug trigger usage.
v2: drop superfluous debug message
v3: comment forced detection, need to debug (Eugeni)
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
VLV supports two dp panels, there are two set of panel power sequence
registers which needed to be programmed based on the configured
pipe. This patch add supports for the same
Acked-by: Acked-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Beeresh G <beeresh.g@intel.com>
Reviewed-by: Vijay Purushothaman <vijay.a.purushothaman@intel.com>
Reviewed-by: Jesse Barnes <jesse.barnes@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Drop the lone hunk and only keep the register definitions - I
loathe incomplete bandaids. Also add a comment that this is for vlv.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add some VLV limit structures and update the PLL code.
v2: resolve conflicts, Vijay to re-post with PLL valid checks and fixed limits
v3: re-add dpio write function
v4: squash in Vijay's fixes for the PLL limits and clean up the m/n finder
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Vijay Purushothaman <vijay.a.purushothaman@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is just the minimal patch to disable all this code so that we can
do decent amounts of QA before we rip it all out.
The complicating thing is that we need to flush the gpu caches after
the batchbuffer is emitted. Which is past the point of no return where
execbuffer can't fail any more (otherwise we risk submitting the same
batch multiple times).
Hence we need to add a flag to track whether any caches associated
with that ring are dirty. And emit the flush in add_request if that's
the case.
Note that this has a quite a few behaviour changes:
- Caches get flushed/invalidated unconditionally.
- Invalidation now happens after potential inter-ring sync.
I've bantered around a bit with Chris on irc whether this fixes
anything, and it might or might not. The only thing clear is that with
these changes it's much easier to reason about correctness.
Also rip out a lone get_next_request_seqno in the execbuffer
retire_commands function. I've dug around and I couldn't figure out
why that is still there, with the outstanding lazy request stuff it
shouldn't be necessary.
v2: Chris Wilson complained that I also invalidate the read caches
when flushing after a batchbuffer. Now optimized.
v3: Added some comments to explain the new flushing behaviour.
Cc: Eric Anholt <eric@anholt.net>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It seems to blow up my ilk in all kinds of strange ways. And now that
we're no longer resetting the entire modeset state, it shouldn't be
necessary any longer.
This essentially reverts
commit f817586ceb
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Tue Apr 10 15:50:11 2012 +0200
drm/i915: re-init modeset hw state after gpu reset
safe for the introduction of modeset_init_hw, that one is nice to
prevent code duplication between driver load and resume.
v2: Add a comment to the code to warn future travellers of the dragon
dungeon ahead, suggested by Chris Wilson.
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The idr code already passes us the pointer associated with that id, so
no need to look it up again. Also, we'll kill the idr right away, so
there's no issue with leaving these dangling pointers behind - the
current code does the same.
v2: Also drop the file argument, spotted by Ben Widawsky.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is our customary "no such object" errno, not -EINVAL.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It doesn't hurt and it at least prevents us from OOPSing left and
right at quite a few places. This also allows us to simplify the code
a bit by folding the only line of context_open into the callsite.
We obviuosly also need to run the cleanup code unconditionally, too.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
commit 8e96d9c4d9
Author: Ben Widawsky <ben@bwidawsk.net>
Date: Mon Jun 4 14:42:56 2012 -0700
drm/i915: reset the GPU on context fini
broke module unload because it reset the gpu before we've stopped
touching it. Later on in the unload sequence the ringbuffer code
complained that the gpu would idle properly (because intel_gpu_reset
only resets the hw and not our sw state).
v2: Reorder things so that we reset the gpu _before_ we release the
backing storage of the default context.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=51183
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Prevents a possible hang: WaDisableL3Bank2xClockGate.
v2: only apply to VLV, IVB doesn't need this anymore
References: https://bugs.freedesktop.org/show_bug.cgi?id=50245
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Another required workaround for a potential hang:
WaDisableTDLUnitClockGating.
v2: only apply this to VLV, IVB doesn't need it anymore (Eugeni)
References: https://bugs.freedesktop.org/show_bug.cgi?id=50245
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
According to the bspec for MBCTL:
Driver must set bit in the following scenarios:
- to realod teh h/w boot context every time it gets loaded through OS
- after an FLR clears the register (BIOS won't run afterwards)
References: https://bugs.freedesktop.org/show_bug.cgi?id=50237
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The RCBP workaround still applies on these chips, and we need VDS as well.
v2: remove MB boot fetch that snuck in (Daniel)
add workaround tags to comments for easier internal tracking (Daniel)
v3: only apply RCPB and VDS on SNB and VLV, IVB doesn't need them (Eugeni)
References: https://bugs.freedesktop.org/show_bug.cgi?id=50251
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I've added a bit of logic such that running the hangman test on chips
without any hw reset support at all doesn't wedge the gpu because the
reset failed. This relied on checking for non-null stop_rings.
Unfortunately I've botched a rebase somewhere and stop_rings is still
cleared at the old place before the reset code.
Fix this up so that running the i-g-t tests on gen2/3 doesn't result
in a wedged gpu.
v2: Actually remove the lines instead of adding them twice ... my git
license should be revoked immediately.
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I'm seeing about a 5% FPS improvement across various benchmarks on my
IVB i3. Rumor has it that the higher end parts show even more benefit.
This derives from a patch originally given to me by Bernard. The docs
are confusing about the definition names (ie. medium really seems like
max), but it would seem it gives more cache to the GT at the expense of
uncore. This configuration makes the split most in favor of the GT. I've
not tried the other IDICOS values.
Cc: "Kilarski, Bernard R" <bernard.r.kilarski@intel.com>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This got dropped as a result of the last round of comments. I didn't
test it on unsupported HW (which this is likely the case).
Note that this prevents hw context from blowing up on any pre-gen6 hw.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=51142
[danvet: Added note and buglink.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Somehow this went unnoticed in the past reviews, but the condition would
never timeout properly.
This was initially introduced in the v2 of original SBI enabling patch.
Highly embarrassing.
Note that we now actually time out for the read, which resulted in gcc
complaining that we can now return unitialized garbage if that
happens. There's not much we can do here because there's not much
point in thread -EIO all the way down through these functions. Hence
simply shut up the compiler.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
[danvet: Added note and squashed uninitialized value shut-up into this
patch.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: cache the EDID for eDP panels
Revert "drm/i915/dp: Use auxch precharge value of 5 everywhere"
drm/i915: eDP aux needs vdd
drm/i915: don't enumerate HDMID if an eDP panel is already active on the port
They aren't going anywhere, and probing on DDC can cause the panel to
blank briefly, so read them up front and cache them for later queries.
v2: fix potential NULL derefs in intel_dp_get_edid_modes and
intel_dp_get_edid (Jani)
copy full EDID length, including extension blocks (Takashi)
free EDID on teardown (Takashi)
v3: malloc a new EDID buffer that's big enough for the memcpy (Chris)
v4: change handling of NULL EDIDs, just preserve the NULL behavior
across detects and mode list fetches rather than trying to re-fetch
the EDID (Chris)
v5: be glad that Chris is around to remind me to hit C-x C-s before
committing.
References: https://bugs.freedesktop.org/show_bug.cgi?id=46856
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reverts commit 092945e11c.
This commit prevents a DP screen from properly training the link.
Oddly enough it works, once the machine has been warm-booted with an
older kernel.
According to DP docs this _should_ have been the right precharge time.
Also, the commit that originally introduces this was just general snb
DP enabling and didn't mention any specific reason for this special
value. Whatever, trust the reporter that this makes things worse and
let's just revert it.
v2: Less spelling fail.
Cc: Adam Jackson <ajax@redhat.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Reported-by: "Wouter M. Koolen" <W.M.Koolen-Wijkstra@cwi.nl>
Buglink: https://lkml.org/lkml/2012/6/14/301
Cc: stable@vger.kernel.org (only for 3.4)
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The new oui probe has been missing these.
This issue has been introduce in
commit 0d19832853
Author: Adam Jackson <ajax@redhat.com>
Date: Mon May 14 16:05:47 2012 -0400
drm/i915/dp: Probe branch/sink OUIs
v2: Do the eDP vdd dance of simply not probing the OUI on eDP panels
as suggested by Chris Wilson.
v3: Fix up the error path fail - I suck.
Cc: Adam Jackson <ajax@redhat.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=50808
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Bugreport: http://permalink.gmane.org/gmane.comp.video.dri.devel/69695
Tested-by: Yang Guang <guang.a.yang@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This prevents the HDMI detect functions from poking at an eDP
connected panel, which can lead to trouble.
[danvet: Note that we have some other reports of DP vs. HDMI fighting,
but the general case is a much bigger fish to fry.]
References: https://bugs.freedesktop.org/show_bug.cgi?id=42278
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Required for streamout. Bump drm minor.
Marek v2: fix pkt->count check
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- SMX_SAR_CTL0 needs to be programmed correctly to prevent
problems with memory exports in certain cases.
- VC_ENHANCE needs to be initialized on 6xx/7xx.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
VGA hotplug detection "works" by measuring the resistance across
certain pins. A lot of kvm switches fumble this and wire up cheap
resistors with the wrong resistance or don't bother at all.
To accomodate these, also try to detect a connected monitor by trying
to grab the edid. Contrary to !HAS_HOTPLUG platforms we don't bother
with an actual load-detection cycle when the output is life - that
would be actual work to implement because things moved around. This is
the big difference to Chris Wilson's original approach:
commit 9e612a008f
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Thu May 31 13:08:53 2012 +0100
drm/i915/crt: Do not rely upon the HPD presence pin
This blew up on Linus' machine because it errornously detected a vga
screen (without and edid and hence only the default modes), leading to
it's prompt removal:
commit 8f53369b75
Author: Linus Torvalds <torvalds@linux-foundation.org>
Date: Fri Jun 8 14:53:06 2012 -0700
Revert "drm/i915/crt: Do not rely upon the HPD presence pin"
Some digging around in Bspec shows the reason why load detect doesn't work on
newer chips - the legacy VGA load detect bit isn't wired up any longer:
Public Snb Bspec, Vol3 Part1, 1.1.1 ST00 Input Status 0, bit4:
"RGB Comparator / Sense. This bit is here for compatibility and will
always return one. Monitor detection must be done be done through the
programming of registers in the MMIO space.
0 = Below threshold
1 = Above threshold"
v2: Add a comment in the code that load detect on hotplug capable
machines is broken and pimp the commit message with a quote of Bspec
to show why.
Reported-and-tested-by: Matthieu LAVIE <boiteamadmax@hotmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=50501
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After recent changes HDMI code is ready to be enabled on DCE5. This
patch just changes conditions to execute already present code on DCE5.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Christian König <christian.koenig@amd.com>
Tested-by: Andre Heider <a.heider@gmail.com>
Tested-by: Zoltán Böszörményi <zboszor@pr.hu>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The filed object_idr of struct drm_sis_private was introduced with
commit http://git.kernel.org/?p=linux/kernel/git/torvalds/linux.git;a=commitdiff;h=6de8a748881f1cd9d795454da2b6db616d5ca3d7 .
The idr_init(&dev->object_name_idr) is called instead of
idr_init(&dev_priv->object_idr) by mistake, leaving object_idr
uninitialized. Correct this.
This patch was not tested because of lack of hardware.
Signed-off-by: Márton Németh <nm127@freemail.hu>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
The field obejct_idr of struct drm_via_private was introduced with the
commit http://git.kernel.org/?p=linux/kernel/git/torvalds/linux.git;a=commitdiff;h=77ee8f3825054f23b17e9c8f728f061defd86cdc .
In that patch idr_init(&dev->object_name_idr) was called instead of
idr_init(&dev_priv->object_idr) by mistake, leaving the dev_priv->object_idr
uninitialized. To be more exact, the object_idr buffer is filled with zeros
because of kzalloc(), but the dev_priv->object_idr.lock spinlock can cause
system freeze at lib/idr.c:move_to_free_list() when spin_lock_irqsave()
is called on this spinlock.
The patch was tested on Clevo D4J, model D410J laptop, on the following
hardware, without AGP kernel module loaded:
# lspci -s 01:00.0 -n
01:00.0 0300: 1106:3108 (rev 01)
# lspci -s 01:00.0 -v
01:00.0 VGA compatible controller: VIA Technologies, Inc. K8M800/K8N800/K8N800A [S3 UniChrome Pro] (rev 01) (prog-if 00 [VGA controller])
Subsystem: CLEVO/KAPOK Computer Device 4702
Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 16
Memory at f0000000 (32-bit, prefetchable) [size=64M]
Memory at d1000000 (32-bit, non-prefetchable) [size=16M]
Expansion ROM at <unassigned> [disabled]
Capabilities: [60] Power Management version 2
Capabilities: [70] AGP version 3.0
Signed-off-by: Márton Németh <nm127@freemail.hu>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
I finally got to test this code a bit more and hit the ttm
no reserved assert, so add the reservations around the pinning.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Not all asics have all rings, so make sure the ring is ready
before attempting to check it in the dynpm work handler.
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=43367
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Use the rsvd1 field in execbuf2 to specify the context ID associated
with the workload. This will allow the driver to do the proper context
switch when/if needed.
v2: Add checks for context switches on rings not supporting contexts.
Before the code would silently ignore such requests.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Add the interfaces to allow user space to create and destroy contexts.
Contexts are destroyed automatically if the file descriptor for the dri
device is closed.
Following convention as usual here causes checkpatch warnings.
v2: with is_initialized, no longer need to init at create
drop the context switch on create (daniel)
v3: Use interruptible lock (Chris)
return -ENODEV in !GEM case (Chris)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
To keep things as sane as possible, switch to the default context before
idling. This should help free context objects, as well as put things in
a more well defined state before suspending.
v2: remove seqno from context switch call (daniel)
return error on failed context switch instead of WARN+continue (daniel)
v3: move idling to i915_gpu idle (from i915_gem_idle) (Chris)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
With the code to do HW context switches in place have the driver load the
default context for the render ring when the driver loads.
The default context will be an ever present context that is available to
switch to at any time for the given ring.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
From http://intellinuxgraphics.org/documentation/SNB/IHD_OS_Vol1_Part3.pdf
[DevSNB] If Flush TLB invalidation Mode is enabled it's the driver's
responsibility to invalidate the TLBs at least once after the previous
context switch after any GTT mappings changed (including new GTT
entries). This can be done by a pipelined PIPE_CONTROL with TLB inv bit
set immediately before MI_SET_CONTEXT.
On GEN7 the invalidation mode is explicitly set, but this appears to be
lacking for GEN6. Since I don't know the history on this, I've decided
to dynamically read the value at ring init time, and use that value
throughout.
v2: better comment (daniel)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
This has showed up in several other patches. It's required for the next
context workaround.
I tested this one on its own and saw no differences in basic tests
(performance or otherwise). This patch is relatively likely to cause
regressions, hence why it's split out.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
The workaround itself applies to gen7 only (according to the docs) and
as Eric Anholt points out shouldn't be required since we don't use HW
scheduling features, and therefore arbitration. Though since it is a
small, and simple addition, and we don't really understand the issue,
just do it.
FWIW, I eventually want to play with some of the arbitration stuff, and
I'd hate to forget about this.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
This way round we don't introduce and ugly layering violations and use
the interface as I planned to use it.
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Implement the context switch code as well as the interfaces to do the
context switch. This patch also doesn't match 1:1 with the RFC patches.
The main difference is that from Daniel's responses the last context
object is now stored instead of the last context. This aids in allows us
to free the context data structure, and context object independently.
There is room for optimization: this code will pin the context object
until the next context is active. The optimal way to do it is to
actually pin the object, move it to the active list, do the context
switch, and then unpin it. This allows the eviction code to actually
evict the context object if needed.
The context switch code is missing workarounds, they will be implemented
in future patches.
v2: actually do obj->dirty=1 in switch (daniel)
Modified comment around above
Remove flags to context switch (daniel)
Move mi_set_context code to i915_gem_context.c (daniel)
Remove seqno , use lazy request instead (daniel)
v3: use i915_gem_request_next_seqno instead of
outstanding_lazy_request (Daniel)
remove id's from trace events (Daniel)
Put the context BO in the instruction domain (Daniel)
Don't unref the BO is context switch fails (Chris)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Invent an abstraction for a hw context which is passed around through
the core functions. The main bit a hw context holds is the buffer object
which backs the context. The rest of the members are just helper
functions. Specifically the ring member, which could likely go away if
we decide to never implement whatever other hw context support exists.
Of note here is the introduction of the 64k alignment constraint for the
BO. If contexts become heavily used, we should consider tweaking this
down to 4k. Until the contexts are merged and tested a bit though, I
think 64k is a nice start (based on docs).
Since we don't yet switch contexts, there is really not much complexity
here. Creation/destruction works pretty much as one would expect. An idr
is used to generate the context id numbers which are unique per file
descriptor.
v2: add DRM_DEBUG_DRIVERS to distinguish ENOMEM failures (ben)
convert a BUG_ON to WARN_ON, default destruction is still fatal (ben)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Very basic code for context setup/destruction in the driver.
Adds the file i915_gem_context.c This file implements HW context
support. On gen5+ a HW context consists of an opaque GPU object which is
referenced at times of context saves and restores. With RC6 enabled,
the context is also referenced as the GPU enters and exists from RC6
(GPU has it's own internal power context, except on gen5). Though
something like a context does exist for the media ring, the code only
supports contexts for the render ring.
In software, there is a distinction between contexts created by the
user, and the default HW context. The default HW context is used by GPU
clients that do not request setup of their own hardware context. The
default context's state is never restored to help prevent programming
errors. This would happen if a client ran and piggy-backed off another
clients GPU state. The default context only exists to give the GPU some
offset to load as the current to invoke a save of the context we
actually care about. In fact, the code could likely be constructed,
albeit in a more complicated fashion, to never use the default context,
though that limits the driver's ability to swap out, and/or destroy
other contexts.
All other contexts are created as a request by the GPU client. These
contexts store GPU state, and thus allow GPU clients to not re-emit
state (and potentially query certain state) at any time. The kernel
driver makes certain that the appropriate commands are inserted.
There are 4 entry points into the contexts, init, fini, open, close.
The names are self-explanatory except that init can be called during
reset, and also during pm thaw/resume. As we expect our context to be
preserved across these events, we do not reinitialize in this case.
As Adam Jackson pointed out, The cutoff of 1MB where a HW context is
considered too big is arbitrary. The reason for this is even though
context sizes are increasing with every generation, they have yet to
eclipse even 32k. If we somehow read back way more than that, it
probably means BIOS has done something strange, or we're running on a
platform that wasn't designed for this.
v2: rename load/unload to init/fini (daniel)
remove ILK support for get_size() (indirectly daniel)
add HAS_HW_CONTEXTS macro to clarify supported platforms (daniel)
added comments (Ben)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
The GPUs can have different default context layouts, and the sizes could
vary based on platform or BIOS. In order to back the context object with
a properly sized BO, we must read this register in order to find out a
sufficient size.
Thankfully (sarcarm!), the register moves and changes meanings
throughout generations.
CTX and CXT differences are intentional as that is how it is in the
documentation (prior to GEN6 it was CXT).
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
- Fix a regression of USB-audio PCM assignment since 3.4
- A few VGA-switcheroo-related fixes for proper HDMI audio enablement
- Fixed the missing initializations of HD-audio verbs, which may have
resulted in various breakage
- Some driver-specific ASoC updates
- A few fixes for the dynamic PCM code
- The addition of pinctrl support for the i.MX audmux which didn't make it
into -rc1 due to cross tree dependency issues
- A few minor fixes in compress API codes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=Hrh7
-----END PGP SIGNATURE-----
Merge tag 'sound-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
- Fix a regression of USB-audio PCM assignment since 3.4
- A few VGA-switcheroo-related fixes for proper HDMI audio enablement
- Fixed the missing initializations of HD-audio verbs, which may have
resulted in various breakage
- Some driver-specific ASoC updates
- A few fixes for the dynamic PCM code
- The addition of pinctrl support for the i.MX audmux which didn't make
it into -rc1 due to cross tree dependency issues
- A few minor fixes in compress API codes
* tag 'sound-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Don't forget to call init verbs added by fixup list
ALSA: HDA: Pin fixup for Zotac Z68 motherboard
ALSA: compress_core: cleanup pointers on stop
ALSA: compress_core: don't wake up on pause
ALSA: hda - Fix detection of Creative SoundCore3D controllers
vga_switcheroo: Enable/disable audio clients at the right time
ALSA: hda - HDMI Audio init all connectors when VGA-switcheroo is off
vga_switcheroo: Fix error without CONFIG_VGA_SWITCHEROO
ALSA: hda - Fix uninitialized HDMI controllers with VGA-switcheroo
vga_switcheroo: Add a helper function to get the client state
ALSA: usb-audio: Fix substream assignments
ASoC: tegra: add MODULE_DEVICE_TABLE to tegra30_ahub
ASoC: wm2000: Always use a 4s timeout for the firmware
ASoC: dapm: Fix input list to use source widgets
ASoC: dpcm: Fix dpcm_get_be() to check that DAI is BE
ASoC: wm8994: Apply volume updates with clocks enabled
ASoC: wm8994: Ensure all AIFnCLK events are run from the _late variants
ASoC: imx-audmux: add pinctrl support
ASoC: dapm: Fix connected widget capture path query.
The Lenovo Thinkpad T410 has the LVDS_PIPEB_SELECT bit set in the LVDS
register when booted with the lid closed, even though the LVDS hasn't
really been initialized. Ignore this bit so that the VBT value will be
used instead.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As we switch on/off the primary plane if it is completely obscured by an
overlapping video sprite, we also nee to make sure that we update the
FBC configuration at the same time.
v2: Not all crtcs are intel_crtcs, as spotted by Daniel.
v3: Boot testing rules.
References: https://bugs.freedesktop.org/show_bug.cgi?id=50238
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Especially vesafb likes to map everything as uc- (yikes), and if that
mapping hangs around still while we try to map the gtt as wc the
kernel will downgrade our request to uc-, resulting in abyssal
performance.
Unfortunately we can't do this as early as readon does (i.e. as the
first thing we do when initializing the hw) because our fb/mmio space
region moves around on a per-gen basis. So I've had to move it below
the gtt initialization, but that seems to work, too. The important
thing is that we do this before we set up the gtt wc mapping.
Now an altogether different question is why people compile their
kernels with vesafb enabled, but I guess making things just work isn't
bad per se ...
v2:
- s/radeondrmfb/inteldrmfb/
- fix up error handling
v3: Kill #ifdef X86, this is Intel after all. Noticed by Ben Widawsky.
v4: Jani Nikula complained about the pointless bool primary
initialization.
v5: Don't oops if we can't allocate, noticed by Chris Wilson.
v6: Resolve conflicts with agp rework and fixup whitespace.
Reported-and-tested-by: "Kilarski, Bernard R" <bernard.r.kilarski@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When drm/i915 is in control of the gtt, we need to call
the enable function at all the relevant places ourselves.
Reviewed-by: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To be able to directly set up the intel-gtt code from drm/i915 and
avoid setting up the fake-agp driver we need to prepare a few things:
- pass both the bridge and gpu pci_dev to the probe function and add
code to handle the gpu pdev both being present (for drm/i915) and
not present (fake agp).
- add refcounting to the remove function so that unloading drm/i915
doesn't kill the fake agp driver
v2: Fix up the cleanup and refcount, noticed by Jani Nikula.
Reviewed-by: Jani Nikula <jani.nikula@linux.intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For that to work we need to export the base address of the gtt
mmio window from intel-gtt. Also replace all other uses of
dev->agp by values we already have at hand.
Reviewed-by: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Given the havoc the missing backlight pipe select code might have
caused, let's try to re-enabled pipe A support for lvds on gen4 hw.
Just to see what all blows up ...
Note though that
commit 4add75c43f
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Sat Dec 4 17:49:46 2010 +0000
drm/i915: Allow LVDS to be on pipe A for Ironlake+
claims that this caused tons of spurious wakeups somehow.
More details can be found in the old revert:
commit 12e8ba25ef
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Tue Sep 7 23:39:28 2010 +0100
Revert "drm/i915: Allow LVDS on pipe A on gen4+"
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=16307
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On gen4+ we have a bitfield to specify from which pipe the backlight
controller should take it's clock. For PCH split platforms we've
already set these up, but only at initialization time. And without
taking into account the 3rd pipe added with ivb.
For gen4, we've completely ignored these. Although we do restrict lvds
to the 2nd pipe, so this is only a problem on machines where we boot
up with the lvds on the first pipe.
So restructure the code to enable the backlight on the right pipe at
modeset time.
v2: For odd reasons panel_enable_backlight gets called twice in a
modeset, so we can't WARN_ON in there if the backlight controller is
switched on already.
v3: backlight enable can also be called through dpms on, so the check
in there is legit. Update the comment to reflect that.
Tested-By: Kamal Mostafa <kamal@canonical.com>
Bugzilla: https://bugs.launchpad.net/bugs/954661
Cc: Carsten Emde <C.Emde@osadl.org>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- Regroup definitions for BLC_PWM_CTL so that they're all together and
and ordered according to the bitfields.
- Add all missing definitions for BLC_PWM_CTL2.
- Use the BLM_ (for backlight modulation) prefix consistently.
- Note that combination mode (i.e. also taking the legacy backlight
control value from pci config space into account) is gen4 only.
- Move the new registers for PCH-split machines up, they're an almost
match for the gen4 defitions. Prefix the special PCH-only bits with
BLM_PCH_. Also add the pipe C select bit for ivb.
- Rip out the second pair of PCH polarity definitions - they're only
valid on early (pre-production) ilk silicon.
- Adapt the existing code to use the new definitions. This has the
nice benefit of killing a magic (1 << 30) left behind be Jesse
Barnes.
No functional changes in this patch.
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We already correctly ignore bit0 on gen < 4, now we also know why ;-)
I've decided that losing that single bit of precision isn't worth the
trouble to sprinkle IS_PINEVIEW checks all over the backlight control
code - that code is way too fragile imo.
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This function is supposed to be used at mode set time, so prevent
against future mistakes by adding a WARN().
Based on a patch by Paulo Zanoni, with the check extracted into a
little assert_hdmi_port_disabled helper added to make things self
documenting and move the assert stuff out of line.
[fixed up spelling goof-up while applying.]
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A regression was introduced in the 3.3 rc series, commit
"drm/ttm: simplify memory accounting for ttm user v2",
causing the metadata of buffer objects created using the ttm_bo_create()
function to be accounted twice.
That causes massive leaks with the vmwgfx driver running for example
SpecViewperf Catia-03 test 2, eventually killing the app.
Furthermore, the same commit introduces a regression where
metadata accounting is leaked if a buffer object is
initialized with an illegal size. This is also fixed with this commit.
v2: Fixed an error path and removed an unused variable.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fix regresson since the introduction of command stream checking on
evergreen (thread referenced below). Issue is cause by ddx allocating
bo with formula width*height*bpp while programming the GPU command
stream with ALIGN(height, 8). In some case (where page alignment does
not hide the extra size bo should be according to height alignment)
the kernel will reject the command stream.
This patch reprogram the command stream to slice - 1 (slice is
a derivative value from height) which avoid rejecting the command
stream while keeping the value of command stream checking from a
security point of view.
This patch also fix wrong computation of layer size for 2D tiled
surface. Which should fix issue when 2D color tiling is enabled.
This dump the radeon KMS_DRIVER_MINOR so userspace can know if
they are on a fixed kernel or not.
https://lkml.org/lkml/2012/6/3/80https://bugs.freedesktop.org/show_bug.cgi?id=50892https://bugs.freedesktop.org/show_bug.cgi?id=50857
!!! STABLE need a custom version of this patch for 3.4 !!!
v2: actually bump the minor version and add comment about stable
v3: do compute the height the ddx was trying to use
[airlied: drop left over debug]
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The audio clients have to be disabled before disabling the VGA and
switching. Similarly, enabling the audio client should be done at
last. Otherwise the audio-side operation stalls, eventually leading
to Oops or lockups.
Tested-by: Jörg-Volker Peetz <jvpeetz@web.de>
Acked-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This reverts commit 9e612a008f.
It incorrectly finds VGA connectors where none are attached, apparently
not noticing that nothing replied to the EDID queries, and happily using
the default EDID modes that have nothing to do with actual hardware.
That in turn then causes X to fall down to the lowest common
denominator, which is usually the default 1024x768 mode that is in the
default EDID and pretty much anything supports).
I'd suggest that if not relying on the HDP pin, the code should at least
check whether it gets valid EDID data back, rather than just assume
there's something on the VGA connector.
Cc: Dave Airlie <airlied@linux.ie>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add vga_switcheroo_get_client_state() to get the current state of the
client. This is necessary to determine the proper initial state of
audio clients in HD-audio driver.
Acked-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* 'exynos-drm-fixes' of git://git.infradead.org/users/kmpark/linux-samsung:
drm/exynos: fixed blending for hdmi graphic layer
drm/exynos: Remove dummy encoder get_crtc operation implementation
drm/exynos: Keep a reference to frame buffer GEM objects
drm/exynos: Don't cast GEM object to Exynos GEM object when not needed
drm/exynos: DRIVER_BUS_PLATFORM is not a driver feature
drm/exynos: fixed size type.
drm/exynos: Use DRM_FORMAT_{NV12, YUV420} instead of DRM_FORMAT_{NV12M, YUV420M}
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: pch_irq_handler -> {ibx, cpt}_irq_handler
char/agp: add another Ironlake host bridge
drm/i915: fix up ivb plane 3 pageflips
drm/i915: hold forcewake around ring hw init
drm/i915: Mark the ringbuffers as being in the GTT domain
drm/i915/crt: Do not rely upon the HPD presence pin
drm/i915: Reset last_retired_head when resetting ring
Cougar/Panther Point redefine the bits in SDEIIR pretty completely.
This function is just debugging, but if we're debugging we probably want
to be told accurate things instead of lies.
I'm told Lynx Point changes this yet more, but I have no idea how...
Note from Eugeni's review:
"For the record and for future enabling efforts, for LPT, bits 28-31
and 1-14 are gone since CPT/PPT (e.g., those must be zero). And there
is the bit 15 as a new addition, but we are not using it yet and
probably won't be using in foreseeable future."
Signed-off-by: Adam Jackson <ajax@redhat.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=35103
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Change the ns_timeout parameter of the wait ioctl to a signed value.
Doing this allows the kernel to provide an infinite wait when a timeout
of less than 0 is provided. This mimics select/poll.
Initially the parameter was meant to match up with the GL spec 1:1, but
after being made aware of how much 2^64 - 1 nanoseconds actually is, I
do not think anyone will ever notice the loss of 1 bit.
The infinite timeout on waiting is similar to the existing i915
userspace interface with the exception that struct_mutex is dropped
while doing the wait in this ioctl.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bspec Vol 3, Part 3, Section 3.8.1.1, bit 30:
"[DevIBX] Writing to this bit only takes effect when port is enabled.
Due to hardware issue it is required that this bit be cleared when port
is disabled. To clear this bit software must temporarily enable this
port on transcoder A."
Unfortunately the public Bspec misses totally out on the same language
for HDMIB. Internal Bspec also mentions that one of the bad
side-effects is that DPx can fail to light up on transcoder A if HDMIx
is disabled but using transcoder B.
I've found this while reviewing Bsepc. We already implement the same
workaround for the DP ports.
Also replace a magic 1 with PIPE_B I've found while looking through the
code.
v2: Implement suggestions from Chris Wilson:
- add pipe variable to cut down on code noise
- write the reg value twice to w/a hw issues (Bspec is unclear on
which bit actually require the write twice stuff, but better be
paranoid about it)
- untangle the if logic
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Or at least plug another gapping hole. Apparrently hw desingers only
moved the bit field, but did not bother ot re-enumerate the planes
when adding support for a 3rd pipe.
Discovered by i-g-t/flip_test.
This may or may not fix the reference bugzilla, because that one
smells like we have still larger fish to fry.
v2: Fixup the impossible case to catch programming errors, noticed by
Chris Wilson.
References: https://bugs.freedesktop.org/show_bug.cgi?id=50069
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Eugeni Dodonov <eugeni.dodonov@intel.com>
Cc: stable@vger.kernel.org
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Locking mutex in different orders just screams for
deadlocks, and some testing showed that it is actually
quite easy to trigger them.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
- Properly set up the RBs
- Properly set up the SPI
- Properly set up gb_addr_config
This should fix rendering issues on certain cards.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Many TVs and A/V receivers don't work with this bit set. Problem was
confirmed using: Onkyo TX-SR605, Sony BRAVIA KDL-52X3500, Sony BRAVIA
KDL-40S40xx. In theory this bit shouldn't affect audio engine when
feeding it with data, however it seems it does. Driver fglrx doesn't set
that bit in any of the above cases.
This fixes a regression introduced by 3.5-rc1.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is based on info released by AMD, should allow using audio in much
more cases.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Call it in the asic startup callback on all asics.
Previously r600 and rv770 called it in the startup
and resume callbacks while all the other asics called
it in the startup callback.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Blending for graphic layer 0 of hdmi mixer was not set so video
layer cannot be showed if graphic layer 0 is enabled.
This patch fixes blending values to support blending between
graphic layer 0 and video layer.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The encoder get_crtc operation is called to retrieve a pointer to the
CRTC the encoder is currenctly connected to, right after setting the
encoder::crtc field to the new CRTC. The implementation of this
operation returns the pointer to the new CRTC, which is then pointlessly
compared to itself.
As the operation is not mandatory, don't implement it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
GEM objects used by frame buffers must be referenced for the whole life
of the frame buffer. Release the references in the frame buffer
destructor instead of its constructor.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
The exynos_drm_gem_dumb_map_offset() doesn't need to access any
Exynos-specific GEM object fields, don't cast the GEM object.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
DRIVER_BUS_PLATFORM is a bus type used internally in the DRM core, not a
flag for the drm_driver::driver_features field.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
The NV12M/YUV420M formats are identical to the already existing standard
NV12/YUV420 formats. The M variants will be removed, so convert the
driver to use the standard names.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
This makes for easier benchmarking and testing. One can set a fixed
frequency by setting min and max to the same value.
v2: fix whitespace & comment (Eugeni)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Eugeni Dodonov <eugeni@dodonov.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We should only frob adjusted_mode. This is in preparation of
a massive patch by Laurent Pinchart to make the mode argument
const.
After the previous two prep patches the only thing left is to clean up
things a bit. I've opted to pass in an adjust_mode param to
dp_adjust_dithering because that way we can be sure to avoid
duplicating this logic between mode_valid and mode_fixup - which was
the cause behind a dp link bw calculation bug in the past.
Also mark the mode argument of pch_panel_fitting const.
v2: Split up the mode->clock => adjusted_mode->clock change,
as suggested by Chris Wilson.
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
... instead of changing mode->clock, which we should leave as-is.
After the previous patch we only touch that if it's a panel, and then
adjusted mode->clock equals adjusted_mode->clock. Outside of
intel_dp.c we only use ajusted_mode->clock in the mode_set functions.
Within intel_dp.c we only use it to calculate the dp dithering
and link bw parameters, so that's the only thing we need to fix
up.
As a temporary ugliness (until the cleanup in the next patch) we
pass the adjusted_mode into dp_dither for both parameters (because
that one still looks at mode->clock).
Note that we do overwrite adjusted_mode->clock with the selected dp
link clock, but that only happens after we've calculated everything we
need based on the dotclock of the adjusted output configuration.
Outside of intel_dp.c only intel_display.c uses adjusted_mode->clock,
and that stays the same after this patch (still equals the selected dp
link clock). intel_display.c also needs the actual dotclock (as
target_clock), but that has been fixed up in the previous patch.
v2: Adjust the debug message to also use adjusted_mode->clock.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
... instead of abusing mode->clock by storing it in there - we
shouldn't touch that one at all. This patch is the first prep step to
constify the mode argument of the intel_dp_mode_fixup function.
The next patch will stop us from modifying mode->clock.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Empirical evidence suggests that we need to: On at least one ivb
machine when running the hangman i-g-t test, the rings don't properly
initialize properly - the RING_START registers seems to be stuck at
all zeros.
Holding forcewake around this register init sequences makes chip reset
reliable again. Note that this is not the first such issue:
commit f01db988ef
Author: Sean Paul <seanpaul@chromium.org>
Date: Fri Mar 16 12:43:22 2012 -0400
drm/i915: Add wait_for in init_ring_common
added delay loops to make RING_START and RING_CTL initialization
reliable on the blt ring at boot-up. So I guess it won't hurt if we do
this unconditionally for all force_wake needing gpus.
To avoid copy&pasting of the HAS_FORCE_WAKE check I've added a new
intel_info bit for that.
v2: Fixup missing commas in static struct and properly handling the
error case in init_ring_common, both noticed by Jani Nikula.
Cc: stable@vger.kernel.org
Reported-and-tested-by: Yang Guang <guang.a.yang@intel.com>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=50522
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
By correctly describing the rinbuffers as being in the GTT domain, it
appears that we are more careful with the management of the CPU cache
upon resume and so prevent some coherency issue when submitting commands
to the GPU later. A secondary effect is that the debug logs are then
consistent with the actual usage (i.e. they no longer describe the
ringbuffers as being in the CPU write domain when we are accessing them
through an wc iomapping.)
Reported-and-tested-by: Daniel Gnoutcheff <daniel@gnoutcheff.name>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=41092
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Both busy_ioctl and the new wait_ioct need to do the same dance (or at
least should). Some slight changes:
- busy_ioctl now unconditionally checks for olr. Before emitting a
require flush would have prevent the olr check and hence required a
second call to the busy ioctl to really emit the request.
- the timeout wait now also retires request. Not really required for
abi-reasons, but makes a notch more sense imo.
I've tested this by pimping the i-g-t test some more and also checking
the polling behviour of the wait_rendering_timeout ioctl versus what
busy_ioctl returns.
v2: Too many people complained about unplug, new color is
flush_active.
v3: Kill the comment about the unplug moniker.
v4: s/un-active/inactive/
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull drm fixes from Dave Airlie:
"A bunch of fixes:
- vmware memory corruption
- ttm spinlock balance
- cirrus/mgag200 work in the presence of efifb
and finally Alex and Jerome managed to track down a magic set of bits
that on certain rv740 and evergreen cards allow the correct use of the
complete set of render backends, this makes the cards operate
correctly in a number of scenarios we had issues in before, it also
manages to boost speed on benchmarks my large amounts on these
specific gpus."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/edid: Make the header fixup threshold tunable
drm/radeon: fix regression in UMS CS ioctl
drm/vmwgfx: Fix nasty write past alloced memory area
drm/ttm: Fix spinlock imbalance
drm/radeon: fixup tiling group size and backendmap on r6xx-r9xx (v4)
drm/radeon: fix HD6790, HD6570 backend programming
drm/radeon: properly program gart on rv740, juniper, cypress, barts, hemlock
drm/radeon: fix bank information in tiling config
drm/mgag200: kick off conflicting framebuffers earlier.
drm/cirrus: kick out conflicting framebuffers earlier
cirrus: avoid crash if driver fails to load
Instead of checking for !CPT, check for IBX to make it clearer that
this is a IBX-specific workaround. No functional change because we
smash the PPT PCH into the HAS_PCH_CPT check and atm DP isn't enabled
on the haswell LPT PCH yet.
See Bspec Vol 3, Part 3, Section 4.[3-5].1 about DP[BCD], bit 30 for
details of this workaround.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull vfs changes from Al Viro.
"A lot of misc stuff. The obvious groups:
* Miklos' atomic_open series; kills the damn abuse of
->d_revalidate() by NFS, which was the major stumbling block for
all work in that area.
* ripping security_file_mmap() and dealing with deadlocks in the
area; sanitizing the neighborhood of vm_mmap()/vm_munmap() in
general.
* ->encode_fh() switched to saner API; insane fake dentry in
mm/cleancache.c gone.
* assorted annotations in fs (endianness, __user)
* parts of Artem's ->s_dirty work (jff2 and reiserfs parts)
* ->update_time() work from Josef.
* other bits and pieces all over the place.
Normally it would've been in two or three pull requests, but
signal.git stuff had eaten a lot of time during this cycle ;-/"
Fix up trivial conflicts in Documentation/filesystems/vfs.txt (the
'truncate_range' inode method was removed by the VM changes, the VFS
update adds an 'update_time()' method), and in fs/btrfs/ulist.[ch] (due
to sparse fix added twice, with other changes nearby).
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (95 commits)
nfs: don't open in ->d_revalidate
vfs: retry last component if opening stale dentry
vfs: nameidata_to_filp(): don't throw away file on error
vfs: nameidata_to_filp(): inline __dentry_open()
vfs: do_dentry_open(): don't put filp
vfs: split __dentry_open()
vfs: do_last() common post lookup
vfs: do_last(): add audit_inode before open
vfs: do_last(): only return EISDIR for O_CREAT
vfs: do_last(): check LOOKUP_DIRECTORY
vfs: do_last(): make ENOENT exit RCU safe
vfs: make follow_link check RCU safe
vfs: do_last(): use inode variable
vfs: do_last(): inline walk_component()
vfs: do_last(): make exit RCU safe
vfs: split do_lookup()
Btrfs: move over to use ->update_time
fs: introduce inode operation ->update_time
reiserfs: get rid of resierfs_sync_super
reiserfs: mark the superblock as dirty a bit later
...
6 bytes seems to be a reasonable default so far, but for the desperate
it's worth exposing this.
[airlied: change include to module.h for this]
Bugzilla: https://bugzilla.redhat.com/582559
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
radeon_cs_parser_init is called by both the legacy UMS
CS ioctl and the KMS CS ioctl. Protect KMS specific
pieces of the code by checking that rdev is not NULL.
Reported-by: Michael Burian <michael.burian@sbg.at>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
This imbalance may cause hangs when TTM is trying to swap out a buffer
that is already on the delayed delete list.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Tiling group size is always 256bits on r6xx/r7xx/r8xx/9xx. Also fix and
simplify render backend map. This now properly sets up the backend map
on r6xx-9xx which should improve 3D performance.
Vadim benchmarked also:
Some benchmarks on juniper (5750), fullscreen 1920x1080,
first result - kernel 3.4.0+ (fb21affa), second - with these patches:
Lightsmark: 91 fps => 123 fps +35%
Doom3: 74 fps => 101 fps +36%
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Need to program an additional VM register. This doesn't not currently
cause any problems, but allows us to program the proper backend
map in a subsequent patch which should improve performance on these
asics.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
While there are cards with more than 8 mem banks, the max
number of banks from a tiling perspective is 8, so cap
the tiling config at 8 banks.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=43448
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
It appears grub2 can pass framebuffer info via efifb, so
we need to kick it off earlier to reserve the vram allocation.
(just a fixup same as for cirrus)
Signed-off-by: Dave Airlie <airlied@redhat.com>
It appears that grub2 will pass framebuffer info via EFI,
this causes the vram reserve to fail, so kick out efifb
earlier before cirrus loads.
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=826983
Signed-off-by: Dave Airlie <airlied@redhat.com>
We need the latest dma-buf code from Dave Airlie so that we can pimp
the backing storage handling code in drm/i915 with Chris Wilson's
unbound tracking and stolen mem backed gem object code.
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Positively checking for the required feature/gen is simpler than build
a cascade of negative "we need to bail" checks. And the later won't
scale if we add more stuff that doesn't fit in nicely.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This fixes an (albeit really hard to hit) race resulting in an oops:
- The parity work get scheduled.
- We re-init the irq state and call INIT_WORK again.
- The workqueue code tries to run the work item and stumbles over a
work item that should be on it's runlist.
Also initiliaze the work item unconditionally like all the others,
it's simpler.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Whilst most monitors do wire up the HPD presence pin, it seems quite a
few KVM do not. Therefore if we simply rely on the HPD pin being
asserted to indicate a connected monitor we fail miserable, so fall back
to performing a DCC query for the EDID.
Reported-and-tested-by: Matthieu LAVIE <boiteamadmax@hotmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=50501
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Dumb binary interfaces which allow root-only updates of the cache
remapping registers. As mentioned in a previous patch, software using
this interface needs to know about HW limits, and other programming
considerations as the kernel interface does no checking for these things
on the root-only interface.
v1: Drop extra posting reads (Chris)
Return negative values in the sysfs interfaces on errors (Chris)
v2: Return -EINVAL for offset % 4 (Jesse)
Move schizo userspace check out (Jesse)
Cleaner sysfs item initializers (Daniel)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If any l3 rows have been previously remapped, we must remap them after
GPU reset/resume too.
v2: Just return (no warn) on remapping init if not IVB (Jesse)
Move the check of schizo userspace to i915_gem_l3_remap (Jesse)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The previous patch put all the code, and handlers in place. It should
now be safe to enable the parity error interrupt. The parity error must
be unmasked in both the GTIMR, and the CS IMR. Unfortunately, the docs
aren't clear about this; nevertheless it's the truth.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On IVB hardware we are given an interrupt whenever a L3 parity error
occurs in the L3 cache. The L3 cache is used by internal GPU clients
only. This is a very rare occurrence (in fact to test this I need to
use specially instrumented silicon).
When a row in the L3 cache detects a parity error the HW generates an
interrupt. The interrupt is masked in GTIMR until we get a chance to
read some registers and alert userspace via a uevent. With this
information userspace can use a sysfs interface (follow-up patch) to
remap those rows.
Way above my level of understanding, but if a given row fails, it is
statistically more likely to fail again than a row which has not failed.
Therefore it is desirable for an operating system to maintain a lifelong
list of failing rows and always remap any bad rows on driver load.
Hardware limits the number of rows that are remappable per bank/subbank,
and should more than that many rows detect parity errors, software
should maintain a list of the most frequent errors, and remap those
rows.
V2: Drop WARN_ON(IS_GEN6) (Jesse)
DRM_DEBUG row/bank/subbank on errror (Jesse)
Comment updates (Jesse)
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A 30 ms delay is simply way too big to waste cpu cycles on.
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jesse extracted this nice helper in his i9xx_crtc_mode_set refactor,
but we have the identical code in ironlake_ccrtc_mode_set. And that
function is huge, so extracting some code full of magic numbers is
always nice.
Noticed while trying to get a handle on our dp clock code.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Already discovered in
commit 5a117db77e
Author: Eugeni Dodonov <eugeni.dodonov@intel.com>
Date: Thu Jan 5 09:34:29 2012 -0200
drm/i915: there is no pipe CxSR on ironlake
but we've failed to rip out the code from the ironlake specific code.
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Weirdness around do_mmap() in there does not rely on ->mmap_sem for
exclusion, so no need to keep it under that. As the result, we can
turn that do_mmap() into vm_mmap().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
On IVB and older, we basically have two registers: the control and the
data register. We write a few consecutitve times to the control
register, and we need these writes to arrive exactly in the specified
order.
Also, when we're changing the data register, we need to guarantee that
anything written to the control register already arrived (since
changing the control register can change where the data register
points to). Also, we need to make sure all the writes to the data
register happen exactly in the specified order, and we also *can't*
read the data register during this process, since reading and/or
writing it will change the place it points to.
So invoke the "better safe than sorry" rule and just be careful and
put barriers everywhere :)
On HSW we still have a control register that we write many times, but
we have many data registers.
Demanded-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
HSW support is now just like all the other generations: we send AVI
and SPD InfoFrames. There are other DIPs for HSW, but there are other
DIPs for the previous generations too. For each gen, we can see which
DIPs are missing by looking at the 'set_infoframes' function: we
explicitly disable the DIPs we're not using.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The register that controls the HDMI port can be used to control the
sDVO port. Some bits are defined only for sDVO, and SDVO_BORDER_ENABLE
is one of those: HDMI ports that can't be used in sDVO mode don't even
have this bit defined in their specifications.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
At this time, the HDMI port is enabled, and the DIP control register
specification says we need to disable the port *before* disabling the
DIPs. Also, while doing this we risk telling the HW to send the AVI
DIPs once (not every VSync), which really seems to confuse the HW and
trigger bugs where the DIPs are not sent.
This code was here just to set the DIP register to a 'known state'
before using it, but since now the set_infoframes functions already
set the control registers to a known state, this code can go away.
Also, the previous code disables *all* the DIP registers for *each*
HDMI port, so we end disabling each DIP register more than once.
This patch solves a problem I can reproduce on my IVB machine. When I
boot it with just a single HDMI monitor, the AVI InfoFrames are not
sent. With this patch, the InfoFrames are sent. Previously, I wrote a
patch to 'touch the DIP registers after we enable the HDMI port' to
solve this same problem, but that patch doesn't seem to be needed
anymore after this patch.
All this patch does is revert a chunk of the following commit:
commit 64a8fc0145
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Thu Sep 22 11:16:00 2011 +0530
drm/i915: fix ILK+ infoframe support
So bugs that can be bisected to that commit may be fixed now.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=43256
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The register specification says we need to do this.
V2: Only write the register if the port is enabled.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From this point on, the 'set_infoframe' functions always set the DIP
registers to a known state, so anything done will always be undone at
the modeset.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This function is called when the pipe is disabled, so it always gets
the 50ms timeout.
This function is called once for each InfoFrame, so we actually get a
100ms timeout. Will be more if we add more InfoFrames.
Also, the spec says we need to "wait for a VSync to ensure completion
of any pending DIP transmissions", not for a VBlank. OTOH, the
register documentation suggests that the DIPs are sent *during* the
VSync, so shouldn't we be waiting until *after* the VSync to ensure
all DIPs are sent?
So this wait_for_vblank seems, besides useless, totally wrong.
If we ever want to change some specific InfoFrame on-the-fly (outside
of the modeset code), the code that changes the InfoFrame will have to
do the waiting itself, and properly.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So the write_infoframe function can assume the DIP is on.
V2: Be more defensive and add WARN().
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Not once for each InfoFrame. Now we have a function that allows us to
do this.
[danvet: Paulo clarified on irc that a later bugfix patch needs this
cleanup.]
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This solves problems that happen when you alternate between HDMI and
DVI on the same port. I can reproduce these problems using DP->HDMI
and DP->DVI adapters on a DP port.
When you first plug HDMI and then plug DVI, you need to stop sending
DIPs, even if the port is in DVI mode (see the HDMI register spec). If
you don't stop sending DIPs, you'll see a pink vertical line on the
left side of the screen, some modes will give you a black screen, some
modes won't work correctly.
When you first plug DVI and then plug HDMI, you need to properly
enable the DIPs, otherwise the HW won't send them. After spending a
lot of time investigating this, I concluded that if the DIPs are
disabled, we should not write to the DIP register again because when
we do this, we also set the AVI InfoFrame frequency to "once", and
this seems to really confuse our hardware. Since this problem was not
exactly easy to debug, I'm adopting the defensive behavior and not
just avoing the "disable twice" sequence, but also explicitly
selecting the AVI InfoFrame and setting its frequency to a correct
one.
Also, move the "is_dvi" check from intel_set_infoframe to the
set_infoframes functions since now they're going to be the first ones
to deal with the DIP registers.
This patch adds the code to fix the problem, but it depends on the
removal of some code that can't be removed right now and will come
later in the patch series. The patch that we need is:
- drm/i915: don't write 0 to DIP control at HDMI init
[danvet: Paulo clarified that this additional patch is only required
to make the fix complete, this patch here alone doesn't introduce a
regression but only partially solves the problem of randomly clearing
the dip registers.]
V2: Be even more defensive by selecting AVI and setting its frequency
outside the "is_dvi" check.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need a function that is able to fully 'set' the state of the DIP
registers to a known state.
Currently, we have the write_infoframe function that is called twice:
once for AVI and once for SPD. The problem is that write_infoframe
tries to keep the state of the DIP register as it is, changing only
the minimum necessary bits. The second problem is that
write_infoframe does twice (once for each time it is called) some
work that should be done only once (like waiting for vblank and
setting the port). If we add even more DIPs, it will do even more
repeated work.
This patch only adds the infrastructure keeping the code behavior the
same as before.
v2: add static keywords
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When we reset the ring control registers, including the HEAD and TAIL of
the ring, we also need to reset associated state. In this instance, we
were failing to reset the cached value of ring->last_retired_head and so
upon the first request for more space following a resume would
potentially (depending on a narrow race window) believe that the HEAD had
advanced much further than reality.
This is a regression from:
commit a71d8d9452
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Wed Feb 15 11:25:36 2012 +0000
drm/i915: Record the tail at each request and use it to estimate the head
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org # 3.4
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Entirely new class of fail for this one. The detailed timings are for
normal CVT but the monitor really wanted CVT-R.
Bugzilla: http://bugzilla.redhat/com/516471
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: tune down the noise of the RP irq limit fail
drm/i915: Remove the error message for unbinding pinned buffers
drm/i915: Limit page allocations to lowmem (dma32) for i965
drm/i915: always use RPNSWREQ for turbo change requests
drm/i915: reject doubleclocked cea modes on dp
drm/i915: Adding TV Out Missing modes.
drm/i915: wait for a vblank to pass after tv detect
drm/i915: no lvds quirk for HP t5740e Thin Client
drm/i915: enable vdd when switching off the eDP panel
drm/i915: Fix PCH PLL assertions to not assume CRTC:PLL relationship
drm/i915: Always update RPS interrupts thresholds along with frequency
drm/i915: properly handle interlaced bit for sdvo dtd conversion
drm/i915: fix module unload since error_state rework
drm/i915: be more careful when returning -ENXIO in gmbus transfer
Only override the ddc bus if the connector doesn't have
a valid one. The existing code overrode the ddc bus for
all connectors even if it had ddc bus.
Fixes ddc on another XFX card with the same pci ids that
was broken by the quirk overwriting the correct ddc bus.
Reported-by: Mehdi Aqadjani Memar <m.aqadjanimemar@student.ru.nl>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The rest of the code uses stdint types, so use them in
drm_property_change_is_valid() as well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Using the wrong union.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
If we hit an error here, then we should unlock and unreference obj
before returning.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Just move its only caller into the same file as it and make it static.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Paulo pointed out that gen4 re-used the SDVO registers for HDMI (the
separate HDMI registers where introduced with the first PCH) and so
g4x_hdmi_connected() never selected the right bit and always returned
disconnected.
Regression in
commit 8ec22b214d
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Fri May 11 18:01:34 2012 +0100
drm/i915/hdmi: Query the live connector status bit for G4x
Cc: Paulo Zanoni <przanoni@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Wait request is poorly named IMO. After working with these functions for
some time, I feel it's much clearer to name the functions more
appropriately.
Of course we must update the callers to use the new name as well.
This leaves room within our namespace for a *real* wait request function
at some point.
Note to maintainer: this patch is optional.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This helps implement GL_ARB_sync but stops short of allowing full blown
sync objects. Finally we can use the new timed seqno waiting function
to allow userspace to wait on a buffer object with a timeout. This
implements that interface.
The IOCTL will take as input a buffer object handle, and a timeout in
nanoseconds (flags is currently optional but will likely be used for
permutations of flush operations). Users may specify 0 nanoseconds to
instantly check.
The wait ioctl with a timeout of 0 reimplements the busy ioctl. With any
non-zero timeout parameter the wait ioctl will wait for the given number
of nanoseconds on an object becoming unbusy. Since the wait itself does
so holding struct_mutex the object may become re-busied before this
completes. A similar but shorter race condition exists in the busy
ioctl.
v2: ETIME/ERESTARTSYS instead of changing to EBUSY, and EGAIN (Chris)
Flush the object from the gpu write domain (Chris + Daniel)
Fix leaked refcount in good case (Chris)
Naturally align ioctl struct (Chris)
v3: Drop lock after getting seqno to avoid ugly dance (Chris)
v4: check for 0 timeout after olr check to allow polling (Chris)
v5: Updated the comment. (Chris)
v6: Return -ETIME instead of -EBUSY when timeout_ns is 0 (Daniel)
Fix the commit message comment to be less ugly (Ben)
Add a warning to check the return timespec (Ben)
v7: Use DRM_AUTH for the ioctl. (Eugeni)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We still don't understand why this fails exactly, but if fails way
too often for a simple debug information. Furthermore the current
ducttape should prevent the gpu from getting stuck at low frequencies.
Hence tune down the dmesg noise.
Note that the known failure case is that the register read returns 0
when the gpu gets confused.
v2: Add comments about the known failure case.
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is now used intentionally to prevent proliferation of is-pinned
checks upon the inactive list following:
commit 1b50247a8d
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Tue Apr 24 15:47:30 2012 +0100
drm/i915: Remove the list of pinned inactive objects
Reported-and-tested-by: guang.a.yang@intel.com
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=50075
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Broadwater and Crestline share a limitation that prevent it from
relocating general surface state above 4GiB. The only recourse we have
since any buffer object may be used as a relocation target is then to
limit all object allocations on 965g[m] to DMA32.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The trace events adds whether or not the wait was blocking. Blocking in
this case means to hold struct_mutex (ie. no new work can be submitted
during the wait). The information is inherently racy.
The blocking information is racy since mutex_is_locked doesn't check
that the current thread holds the lock. The only other option would be
to pass the boolean information of whether or not the class was blocking
down through the stack which is less desirable.
v2: Don't do a trace event per loop. (Chris)
Only get blocking/non-blocking info (Chris)
v3: updated comment in code as well as commit msg (Daniel)
Add "(NB)" to trace information to remind us in 6 months (Ben)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Insert a wait parameter in the code so we can possibly timeout on a
seqno wait if need be. The code should be functionally the same as
before because all the callers will continue to retry if an arbitrary
timeout elapses.
We'd like to have nanosecond granularity, but the only way to do this is
with hrtimer, and that doesn't fit well with the needs of this code.
v2: Fix rebase error (Chris)
Return proper time even in wedged + signal case (Chris + Ben)
Use timespec constructs (Ben)
Didn't take Daniel's advice regarding the Frankenstein-ness of the
function. I did try his advice, but in the end I liked the way the
original code looked, better.
v3: Make wakeups far less frequent for infinite waits (Chris)
v4: Remove dummy_wait variable (Daniel)
Use raw monotonic time instead of jiffies (made the code a bit cleaner) (Ben)
Added a couple of warnings (Ben)
v5: Remove warnings (Daniel)
Use more accurate time diff for default case (Daniel)
Bikeshed for setting the return timespec in timeout case (Daniel)
s/jiffies/time in one of the comments
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull main drm updates from Dave Airlie:
"This is the main merge window request for the drm.
It's big, but jam packed will lots of features and of course 0
regressions. (okay maybe there'll be one).
Highlights:
- new KMS drivers for server GPU chipsets: ast, mgag200 and cirrus
(qemu only). These drivers use the generic modesetting drivers.
- initial prime/dma-buf support for i915, nouveau, radeon, udl and
exynos
- switcheroo audio support: so GPUs with HDMI can turn off the sound
driver without crashing stuff.
- There are some patches drifting outside drivers/gpu into x86 and
EFI for better handling of multiple video adapters in Apple Macs,
they've got correct acks except one trivial fixup.
- Core:
edid parser has better DMT and reduced blanking support,
crtc properties,
plane properties,
- Drivers:
exynos: add 2D core accel support, prime support, hdmi features
intel: more Haswell support, initial Valleyview support, more
hdmi infoframe fixes, update MAINTAINERS for Daniel, lots of
cleanups and fixes
radeon: more HDMI audio support, improved GPU lockup recovery
support, remove nested mutexes, less memory copying on PCIE, fix
bus master enable race (kexec), improved fence handling
gma500: cleanups, 1080p support, acpi fixes
nouveau: better nva3 memory reclocking, kepler accel (needs
external firmware rip), async buffer moves on nv84+ hw.
I've some more dma-buf patches that rely on the dma-buf merge for vmap
stuff, and I've a few fixes building up, but I'd decided I'd better
get rid of the main pull sooner rather than later, so the audio guys
are also unblocked."
Fix up trivial conflict due to some duplicated changes in
drivers/gpu/drm/i915/intel_ringbuffer.c
* 'drm-core-next' of git://people.freedesktop.org/~airlied/linux: (605 commits)
drm/nouveau/nvd9: Fix GPIO initialisation sequence.
drm/nouveau: Unregister switcheroo client on exit
drm/nouveau: Check dsm on switcheroo unregister
drm/nouveau: fix a minor annoyance in an output string
drm/nouveau: turn a BUG into a WARN
drm/nv50: decode PGRAPH DATA_ERROR = 0x24
drm/nouveau/disp: fix dithering not being enabled on some eDP macbooks
drm/nvd9/copy: initialise copy engine, seems to work like nvc0
drm/nvc0/ttm: use copy engines for async buffer moves
drm/nva3/ttm: use copy engine for async buffer moves
drm/nv98/ttm: add in a (disabled) crypto engine buffer copy method
drm/nv84/ttm: use crypto engine for async buffer copies
drm/nouveau/ttm: untangle code to support accelerated buffer moves
drm/nouveau/fbcon: use fence for sync, rather than notifier
drm/nv98/crypt: non-stub implementation of the engine hooks
drm/nouveau/fifo: turn all fifo modules into engine modules
drm/nv50/graph: remove ability to do interrupt-driven context switching
drm/nv50: remove manual context unload on context destruction
drm/nv50: remove execution engine context saves on suspend
drm/nv50/fifo: use hardware channel kickoff functionality
...
Media turbo requests can either use RPVSWREQ or RPNSWREQ to indicate
what the interrupt handler should do. Since we only deal with the
latter in our turbo code, make the media engine use that for turbo
requests.
Cc: stable@vger.kernel.org.
Tested-by: Joe Bloggsian <joebloggsian@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These are ultra-low-res modes used to upscale SDTV content and we
don't know how to support these on dp on intel hw:
- It's unclear whether we can send avi infoframes over dp ports.
- And the pixel repeat setting that work for hdmi/sdvo explicitly
don't work for dp.
So don't bother and just reject these modes. These modes have been
introduced in
commit 54ac76f851
Author: Christian Schmidt <schmidt@digadd.de>
Date: Mon Dec 19 14:53:16 2011 +0000
drm/edid: support CEA video modes.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=45729
Tested-by: Yuang Guang <guang.a.yang@intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These 2 modes were removed by mistake during a clean up.
So, now it is time to add them back. For further info about
supported mode and standard timing table please check:
VOL_3_display_registers_updated.pdf at intellinuxgraphics.org.
Note that this regression has been introduce in
commit 55a6713b3f
Author: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Date: Thu Dec 15 14:47:33 2011 -0200
drm/i915: Removing TV Out modes.
and this commit partially reverts it by re-adding the wrongly removed
modes.
Reported-by: Robert Lowery <rglowery@exemail.com.au>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: Pimped commit message to cite the commit that introduced this
regression.]
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Otherwise the hw will get confused and result in a black screen.
This regression has been most likely introduce in
commit 974b93315b
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Sun Sep 5 00:44:20 2010 +0100
drm/i915/tv: Poll for DAC state change
That commit replace the first msleep(20) with a busy-loop, but failed
to keep the 2nd msleep around. Later on we've replaced all these
msleep(20) by proper vblanks.
For reference also see the commit in xf86-video-intel:
commit 1142be53eb8d2ee8a9b60ace5d49f0ba27332275
Author: Jesse Barnes <jbarnes@hobbes.lan>
Date: Mon Jun 9 08:52:59 2008 -0700
Fix TV programming: add vblank wait after TV_CTL writes
Fxies FDO bug #14000; we need to wait for vblank after
writing TV_CTL or following "DPMS on" calls may not actually enable the output.
v2: As suggested by Chris Wilson, add a small comment to ensure that
no one accidentally removes this vblank wait again - there really
seems to be no sane explanation for why we need it, but it is
required.
Launchpad: https://bugs.launchpad.net/ubuntu/+source/xserver-xorg-video-intel/+bug/763688
Reported-and-Tested-by: Robert Lowery <rglowery@exemail.com.au>
Cc: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Cc: stable@vger.kernel.org
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have one bug report from a validation team that we get the eDP
panel sequencing still somewhat wrong: We need to enable VDD while
switching off the panel and backlight. Unfortunately that reporter
seems to have fallen off the earth :(
For another reporter this actually fixes a black panel issue because
without this the backlight/panel gets confused and doesn't light up
again.
v2: I've forgotten to remove the vdd_off call in panel_off which is
now bogus. This essentially reverts
commit 17038de5f1
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Mon Apr 16 22:43:42 2012 +0100
drm/i915/dp: Flush any outstanding work to turn the VDD off
v3: the current panel_off code forces off the vdd power, too. Which is
bogus and resulted in some funny warnings later on when we've tried to
do aux channel communications with just the vdd forced on. Fix this,
too.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=46312
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=43163
Tested-by: Vincent Frentzel <zcecc22@gmail.com>
Cc: stable@kernel.org
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The existing assertions were written under the assumption that we wanted
to test the related PLL to a CRTC. With the split of PLL into a
separately managed entity which may be shared amongst CRTCs, we need to
pass in both the CRTC and the PLL to the assertion routine.
Occassionally, this means passing NULL for the CRTC as we wish to check
the status of the PLL irrespective of the current CRTC.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In order to avoid missed down-interrupts when coming out of RC6, it is
advised that we always reset the down-threshold upon a PM event. This is
due to that the PM unit goes through a little dance when coming out of
RC6, it first brings the GPU up at the lowest frequency then a short
time later it restores the thresholds. During that interval, the
down-interval may expire and the interrupt be suppressed.
Now aware of the dance taking place within the GPU when coming out of
RC6, one wonders what other writes need to be queued in the fifo buffer
in order to be properly sequenced; setting the RP state appears to be
one.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=44006
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We've simply ignored this, which isn't too great. With this, interlaced
1080i works on my HDMI screen connected through sdvo. For no apparent
reason anything else still doesn't work as it should.
While at it, give these magic numbers in the dtd proper names and
add a comment that they match with EDID detailed timings.
v2: Actually use the right bit for interlaced.
Tested-by: Peter Ross <pross@xvid.org>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: stable@vger.kernel.org
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently nouveau only registers as a vga_switcheroo client, but never
unregisters. This patch adds the necessary unregister calls.
Signed-off-by: Andreas Heider <andreas@meetr.de>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Currently vga_switcheroo_unregister_handler is called unconditionally when
nouveau is unloaded, even when nouveau never registered a handler. This
interferes with other switcheroo handlers, as vga_switcheroo doesn't check who
called unregister_handler, but simply unregisters the current handler. This
patch adds a check so unregister is only called if a handler was registered by
nouveau before.
Signed-off-by: Andreas Heider <andreas@meetr.de>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Disabled for the moment until some performance issues are sorted out, code
committed as a reference point.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Been tested on each major revision that's relevant here, but I'm sure there
are still bugs waiting to be ironed out.
This is a *very* invasive change.
There's a couple of pieces left that I don't like much (eg. other engines
using fifo_priv for the channel count), but that's an artefact of there
being a master channel list still. This is changing, slowly.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
All the places this stuff is actually needed tends to be chipset-specific
anyway, so we're able to just inline the register bashing instead.
The parts of the common code that still directly touch PFIFO temporarily
have conditionals, these will be removed in subsequent commits that will
refactor the fifo modules into engine modules like graph/mpeg etc.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Now have a somewhat simpler semaphore sync implementation for nv17:nv84,
and a switched to using semaphores as fences on nv84+ and making use of
the hardware's >= acquire operation.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Just a cleanup more or less, and to remove the need for special handling of
software objects.
This removes a heap of documentation on dma/graph object formats. The info
is very out of date with our current understanding, and is far better
documented in rnndb in envytools git.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This shouldn't be necessary, I believe this is just a bit of missed debug
code that got left over somehow.
Causes flips to be always synced to vblank, regardless of swap interval,
which we don't want..
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Wait loop can be interrupted by signal, so if signals are raised
periodically (e.g. SIGALRM) this loop may never finish. Use
emission time as a base for fence timeout.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The conditional definition of the generation helper functions apparently
confuses some IDEs....
Reported-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Depending on exact point of failure, not cleaning would lead to
BUG_ONs/oopses in various distant places.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Port change from "drm/nouveau: Keep RAMIN heap within the channel"
to kernel channel, which has its own ramin heap initialisation.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Cc: Younes Manton <younes.m@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Kepler GRAPH has (well, sorta) fixed subchannel<->class assignments, make
this match up to keep it happy without trapping.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This may, perhaps, get re-merged with nvc0_graph.c at some point. It's
still unclear as to how great an idea that'd be. Stay tuned...
Completely dependent on firmware blobs from NVIDIA binary driver currently.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Not entirely convinced 0x004018 transitions are correct yet, but, it's
an improvement.
The 750MHz value comes from fiddling with the binary driver + coolbits on
two different DDR3 NVA8 chipsets (T510 NVS3100M, and NVS300), not a clue
where this number comes from.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Probably not quite right, but this is enough now to make NVS300 reclock
between all 3 of its perflvls correctly.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This probably wants a cleanup, but I'm holding off until I know for sure
how the rest of the things that need doing fit together.
Tested on NVS300 by hacking up perflvl 1 to require PLL mode, and switching
between perflvl 3 and 1.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The binary driver appears to do various bits and pieces of the memory
clock frequency change at different times, depending on the particular
transition that's occuring. I've attempted to replicate this here
for div->pll, pll->div and div->div transitions.
With some additional (patches upcoming) magic regs being bashed, this
allows me to correctly transition between all 3 perflvls on NVS300.
pll->pll transitions will *not* work correctly at the moment, pending
me tricking the binary driver into doing one and seeing how to correctly
handle it.
This patch also handles (hopefully) 0x1110e0, which appears to need
changing depending on whether in PLL or divider mode.. Maybe. We'll
see.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The reg calculation may get moved elsewhere at some point, but lets
figure out what exactly we need to do first.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This adds prime->fd and fd->prime support to radeon.
It passes the sg object to ttm and then populates
the gart entries using it.
Compile tested only.
v2: stub kmap + use new helpers + add reimporting
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This adds handle->fd and fd->handle support to i915, this is to allow
for offloading of rendering in one direction and outputs in the other.
v2 from Daniel Vetter:
- fixup conflicts with the prepare/finish gtt prep work.
- implement ppgtt binding support.
Note that we have squat i-g-t testcoverage for any of the lifetime and
access rules dma_buf/prime support brings along. And there are quite a
few intricate situations here.
Also note that the integration with the existing code is a bit
hackish, especially around get_gtt_pages and put_gtt_pages. It imo
would be easier with the prep code from Chris Wilson's unbound series,
but that is for 3.6.
Also note that I didn't bother to put the new prepare/finish gtt hooks
to good use by moving the dma_buf_map/unmap_attachment calls in there
(like we've originally planned for).
Last but not least this patch is only compile-tested, but I've changed
very little compared to Dave Airlie's version. So there's a decent
chance v2 on drm-next works as well as v1 on 3.4-rc.
v3: Right when I've hit sent I've noticed that I've screwed up one
obj->sg_list (for dmar support) and obj->sg_table (for prime support)
disdinction. We should be able to merge these 2 paths, but that's
material for another patch.
v4: fix the error reporting bugs pointed out by ickle.
v5: fix another error, and stop non-gtt mmaps on shared objects
stop pread/pwrite on imported objects, add fake kmap
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This adds prime->fd and fd->prime support to nouveau,
it passes the SG object to TTM, and then populates the
GART entries using it.
v2: add stubbed kmap + use new function to fill out pages array
for faulting + add reimport test.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This adds the ability for ttm common code to take an SG table
and use it as the backing for a slave TTM object.
The drivers can then populate their GTT tables using the SG object.
v2: make sure to setup VM for sg bos as well.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
udl can only be used as an output offload so doesn't need to support
handle->fd direction.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If userspace attempts to import a buffer it exported on the same device,
we need to return the same GEM handle for it, not a new handle pointing
at the same GEM object.
v2: move removals into a single fn, no need to set to NULL. (Chris Wilson)
Signed-off-by: Dave Airlie <airlied@redhat.com>
the ttm drivers need this currently, in order to get fault handling
working and efficient.
It also allows addrs to be NULL for devices like udl.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Pull trivial updates from Jiri Kosina:
"As usual, it's mostly typo fixes, redundant code elimination and some
documentation updates."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (57 commits)
edac, mips: don't change code that has been removed in edac/mips tree
xtensa: Change mail addresses of Hannes Weiner and Oskar Schirmer
lib: Change mail address of Oskar Schirmer
net: Change mail address of Oskar Schirmer
arm/m68k: Change mail address of Sebastian Hess
i2c: Change mail address of Oskar Schirmer
net: Fix tcp_build_and_update_options comment in struct tcp_sock
atomic64_32.h: fix parameter naming mismatch
Kconfig: replace "--- help ---" with "---help---"
c2port: fix bogus Kconfig "default no"
edac: Fix spelling errors.
qla1280: Remove redundant NULL check before release_firmware() call
remoteproc: remove redundant NULL check before release_firmware()
qla2xxx: Remove redundant NULL check before release_firmware() call.
aic94xx: Get rid of redundant NULL check before release_firmware() call
tehuti: delete redundant NULL check before release_firmware()
qlogic: get rid of a redundant test for NULL before call to release_firmware()
bna: remove redundant NULL test before release_firmware()
tg3: remove redundant NULL test before release_firmware() call
typhoon: get rid of redundant conditional before all to release_firmware()
...
The omapdrm driver uses this for setting per-overlay rotation. It
is likely also useful for setting YUV->RGB colorspace conversion
matrix, etc.
Signed-off-by: Rob Clark <rob@ti.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Christian Koenig