Pull networking fixes from David Miller:
1) Ensure that mtu is at least IPV6_MIN_MTU in ipv6 VTI tunnel driver,
from Steffen Klassert.
2) Fix crashes when user tries to get_next_key on an LPM bpf map, from
Alexei Starovoitov.
3) Fix detection of VLAN fitlering feature for bnx2x VF devices, from
Michal Schmidt.
4) We can get a divide by zero when TCP socket are morphed into
listening state, fix from Eric Dumazet.
5) Fix socket refcounting bugs in skb_complete_wifi_ack() and
skb_complete_tx_timestamp(). From Eric Dumazet.
6) Use after free in dccp_feat_activate_values(), also from Eric
Dumazet.
7) Like bonding team needs to use ETH_MAX_MTU as netdev->max_mtu, from
Jarod Wilson.
8) Fix use after free in vrf_xmit(), from David Ahern.
9) Don't do UDP Fragmentation Offload on IPComp ipsec packets, from
Alexey Kodanev.
10) Properly check napi_complete_done() return value in order to decide
whether to re-enable IRQs or not in amd-xgbe driver, from Thomas
Lendacky.
11) Fix double free of hwmon device in marvell phy driver, from Andrew
Lunn.
12) Don't crash on malformed netlink attributes in act_connmark, from
Etienne Noss.
13) Don't remove routes with a higher metric in ipv6 ECMP route replace,
from Sabrina Dubroca.
14) Don't write into a cloned SKB in ipv6 fragmentation handling, from
Florian Westphal.
15) Fix routing redirect races in dccp and tcp, basically the ICMP
handler can't modify the socket's cached route in it's locked by the
user at this moment. From Jon Maxwell.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (108 commits)
qed: Enable iSCSI Out-of-Order
qed: Correct out-of-bound access in OOO history
qed: Fix interrupt flags on Rx LL2
qed: Free previous connections when releasing iSCSI
qed: Fix mapping leak on LL2 rx flow
qed: Prevent creation of too-big u32-chains
qed: Align CIDs according to DORQ requirement
mlxsw: reg: Fix SPVMLR max record count
mlxsw: reg: Fix SPVM max record count
net: Resend IGMP memberships upon peer notification.
dccp: fix memory leak during tear-down of unsuccessful connection request
tun: fix premature POLLOUT notification on tun devices
dccp/tcp: fix routing redirect race
ucc/hdlc: fix two little issue
vxlan: fix ovs support
net: use net->count to check whether a netns is alive or not
bridge: drop netfilter fake rtable unconditionally
ipv6: avoid write to a possibly cloned skb
net: wimax/i2400m: fix NULL-deref at probe
isdn/gigaset: fix NULL-deref at probe
...
Pull libata fixes from Tejun Heo:
"Three libata fixes:
- fix for a circular reference bug in sysfs code which prevented
pata_legacy devices from being released after probe failure, which
in turn prevented devres from releasing the associated resources.
- drop spurious WARN in the command issue path which can be triggered
by a legitimate passthrough command.
- an ahci_qoriq specific fix"
* 'for-4.11-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: qoriq: correct the sata ecc setting error
libata: drop WARN from protocol error in ata_sff_qc_issue()
libata: transport: Remove circular dependency at free time
Pull workqueue fix from Tejun Heo:
"If a delayed work is queued with NULL @wq, workqueue code explodes
after the timer expires at which point it's difficult to tell who the
culprit was.
This actually happened and the offender was net/smc this time.
Add an explicit sanity check for it in the queueing path"
* 'for-4.11-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: trigger WARN if queue_delayed_work() is called with NULL @wq
Pull percpu fixes from Tejun Heo:
- the allocation path was updating pcpu_nr_empty_pop_pages without the
required locking which can lead to incorrect handling of empty chunks
(e.g. keeping too many around), which is buggy but shouldn't lead to
critical failures. Fixed by adding the locking
- a trivial patch to drop an unused param from pcpu_get_pages()
* 'for-4.11-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu: remove unused chunk_alloc parameter from pcpu_get_pages()
percpu: acquire pcpu_lock when updating pcpu_nr_empty_pop_pages
Yuval Mintz says:
====================
qed: Fixes series
This address several different issues in qed.
The more significant portions:
Patch #1 would cause timeout when qedr utilizes the highest
CIDs availble for it [or when future qede adapters would utilize
queues in some constellations].
Patch #4 fixes a leak of mapped addresses; When iommu is enabled,
offloaded storage protocols might eventually run out of resources
and fail to map additional buffers.
Patches #6,#7 were missing in the initial iSCSI infrastructure
submissions, and would hamper qedi's stability when it reaches
out-of-order scenarios.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Missing in the initial submission, qed fails to propagate qedi's
request to enable OOO to firmware.
Fixes: fc831825f9 ("qed: Add support for hardware offloaded iSCSI")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Need to set the number of entries in database, otherwise the logic
would quickly surpass the array.
Fixes: 1d6cff4fca ("qed: Add iSCSI out of order packet handling")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before iterating over the the LL2 Rx ring, the ring's
spinlock is taken via spin_lock_irqsave().
The actual processing of the packet [including handling
by the protocol driver] is done without said lock,
so qed releases the spinlock and re-claims it afterwards.
Problem is that the final spin_lock_irqrestore() at the end
of the iteration uses the original flags saved from the
initial irqsave() instead of the flags from the most recent
irqsave(). So it's possible that the interrupt status would
be incorrect at the end of the processing.
Fixes: 0a7fb11c23 ("qed: Add Light L2 support");
CC: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: fc831825f9 ("qed: Add support for hardware offloaded iSCSI")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When receiving an Rx LL2 packet, qed fails to unmap the previous buffer.
Fixes: 0a7fb11c23 ("qed: Add Light L2 support");
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current Logic would allow the creation of a chain with U32_MAX + 1
elements, when the actual maximum supported by the driver infrastructure
is U32_MAX.
Fixes: a91eb52abb ("qed: Revisit chain implementation")
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Doorbell HW block can be configured at a granularity
of 16 x CIDs, so we need to make sure that the actual number
of CIDs configured would be a multiplication of 16.
Today, when RoCE is enabled - given that the number is unaligned,
doorbelling the higher CIDs would fail to reach the firmware and
would eventually timeout.
Fixes: dbb799c397 ("qed: Initialize hardware for new protocols")
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko says:
====================
mlxsw: Couple of fixes
Couple or small fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The num_rec field is 8 bit, so the maximal count number is 255.
This fixes vlans learning not being enabled for wider ranges than 255.
Fixes: a4feea74cd ("mlxsw: reg: Add Switch Port VLAN MAC Learning register definition")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The num_rec field is 8 bit, so the maximal count number is 255. This
fixes vlans not being enabled for wider ranges than 255.
Fixes: b2e345f9a4 ("mlxsw: reg: Add Switch Port VID and Switch Port VLAN Membership registers definitions")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we notify peers of potential changes, it's also good to update
IGMP memberships. For example, during VM migration, updating IGMP
memberships will redirect existing multicast streams to the VM at the
new location.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a memory leak, which happens if the connection request
is not fulfilled between parsing the DCCP options and handling the SYN
(because e.g. the backlog is full), because we forgot to free the
list of ack vectors.
Reported-by: Jianwen Ji <jiji@redhat.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
aszlig observed failing ssh tunnels (-w) during initialization since
commit cc9da6cc4f ("ipv6: addrconf: use stable address generator for
ARPHRD_NONE"). We already had reports that the mentioned commit breaks
Juniper VPN connections. I can't clearly say that the Juniper VPN client
has the same problem, but it is worth a try to hint to this patch.
Because of the early generation of link local addresses, the kernel now
can start asking for routers on the local subnet much earlier than usual.
Those router solicitation packets arrive inside the ssh channels and
should be transmitted to the tun fd before the configuration scripts
might have upped the interface and made it ready for transmission.
ssh polls on the interface and receives back a POLL_OUT. It tries to send
the earily router solicitation packet to the tun interface. Unfortunately
it hasn't been up'ed yet by config scripts, thus failing with -EIO. ssh
doesn't retry again and considers the tun interface broken forever.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=121131
Fixes: cc9da6cc4f ("ipv6: addrconf: use stable address generator for ARPHRD_NONE")
Cc: Bjørn Mork <bjorn@mork.no>
Reported-by: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Cc: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Reported-by: Jonas Lippuner <jonas@lippuner.ca>
Cc: Jonas Lippuner <jonas@lippuner.ca>
Reported-by: aszlig <aszlig@redmoonstudios.org>
Cc: aszlig <aszlig@redmoonstudios.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Eric Dumazet pointed out this also needs to be fixed in IPv6.
v2: Contains the IPv6 tcp/Ipv6 dccp patches as well.
We have seen a few incidents lately where a dst_enty has been freed
with a dangling TCP socket reference (sk->sk_dst_cache) pointing to that
dst_entry. If the conditions/timings are right a crash then ensues when the
freed dst_entry is referenced later on. A Common crashing back trace is:
#8 [] page_fault at ffffffff8163e648
[exception RIP: __tcp_ack_snd_check+74]
.
.
#9 [] tcp_rcv_established at ffffffff81580b64
#10 [] tcp_v4_do_rcv at ffffffff8158b54a
#11 [] tcp_v4_rcv at ffffffff8158cd02
#12 [] ip_local_deliver_finish at ffffffff815668f4
#13 [] ip_local_deliver at ffffffff81566bd9
#14 [] ip_rcv_finish at ffffffff8156656d
#15 [] ip_rcv at ffffffff81566f06
#16 [] __netif_receive_skb_core at ffffffff8152b3a2
#17 [] __netif_receive_skb at ffffffff8152b608
#18 [] netif_receive_skb at ffffffff8152b690
#19 [] vmxnet3_rq_rx_complete at ffffffffa015eeaf [vmxnet3]
#20 [] vmxnet3_poll_rx_only at ffffffffa015f32a [vmxnet3]
#21 [] net_rx_action at ffffffff8152bac2
#22 [] __do_softirq at ffffffff81084b4f
#23 [] call_softirq at ffffffff8164845c
#24 [] do_softirq at ffffffff81016fc5
#25 [] irq_exit at ffffffff81084ee5
#26 [] do_IRQ at ffffffff81648ff8
Of course it may happen with other NIC drivers as well.
It's found the freed dst_entry here:
224 static bool tcp_in_quickack_mode(struct sock *sk)↩
225 {↩
226 ▹ const struct inet_connection_sock *icsk = inet_csk(sk);↩
227 ▹ const struct dst_entry *dst = __sk_dst_get(sk);↩
228 ↩
229 ▹ return (dst && dst_metric(dst, RTAX_QUICKACK)) ||↩
230 ▹ ▹ (icsk->icsk_ack.quick && !icsk->icsk_ack.pingpong);↩
231 }↩
But there are other backtraces attributed to the same freed dst_entry in
netfilter code as well.
All the vmcores showed 2 significant clues:
- Remote hosts behind the default gateway had always been redirected to a
different gateway. A rtable/dst_entry will be added for that host. Making
more dst_entrys with lower reference counts. Making this more probable.
- All vmcores showed a postitive LockDroppedIcmps value, e.g:
LockDroppedIcmps 267
A closer look at the tcp_v4_err() handler revealed that do_redirect() will run
regardless of whether user space has the socket locked. This can result in a
race condition where the same dst_entry cached in sk->sk_dst_entry can be
decremented twice for the same socket via:
do_redirect()->__sk_dst_check()-> dst_release().
Which leads to the dst_entry being prematurely freed with another socket
pointing to it via sk->sk_dst_cache and a subsequent crash.
To fix this skip do_redirect() if usespace has the socket locked. Instead let
the redirect take place later when user space does not have the socket
locked.
The dccp/IPv6 code is very similar in this respect, so fixing it there too.
As Eric Garver pointed out the following commit now invalidates routes. Which
can set the dst->obsolete flag so that ipv4_dst_check() returns null and
triggers the dst_release().
Fixes: ceb3320610 ("ipv4: Kill routes during PMTU/redirect updates.")
Cc: Eric Garver <egarver@redhat.com>
Cc: Hannes Sowa <hsowa@redhat.com>
Signed-off-by: Jon Maxwell <jmaxwell37@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. modify bd_status from u32 to u16 in function hdlc_rx_done,
because bd_status register is 16bits
2. write bd_length register before writing bd_status register
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The main item is the addition of the Power9 Machine Check handler. This was
delayed to make sure some details were correct, and is as minimal as possible.
The rest is small fixes, two for the Power9 PMU, two dealing with obscure
toolchain problems, two for the PowerNV IOMMU code (used by VFIO), and one to
fix a crash on 32-bit machines with macio devices due to missing dma_ops.
Thanks to:
Alexey Kardashevskiy, Cyril Bur, Larry Finger, Madhavan Srinivasan, Nicholas
Piggin.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=390M
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.11-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull some more powerpc fixes from Michael Ellerman:
"The main item is the addition of the Power9 Machine Check handler.
This was delayed to make sure some details were correct, and is as
minimal as possible.
The rest is small fixes, two for the Power9 PMU, two dealing with
obscure toolchain problems, two for the PowerNV IOMMU code (used by
VFIO), and one to fix a crash on 32-bit machines with macio devices
due to missing dma_ops.
Thanks to:
Alexey Kardashevskiy, Cyril Bur, Larry Finger, Madhavan Srinivasan,
Nicholas Piggin"
* tag 'powerpc-4.11-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/64s: POWER9 machine check handler
powerpc/64s: allow machine check handler to set severity and initiator
powerpc/64s: fix handling of non-synchronous machine checks
powerpc/pmac: Fix crash in dma-mapping.h with NULL dma_ops
powerpc/powernv/ioda2: Update iommu table base on ownership change
powerpc/powernv/ioda2: Gracefully fail if too many TCE levels requested
selftests/powerpc: Replace stxvx and lxvx with stxvd2x/lxvd2x
powerpc/perf: Handle sdar_mode for marked event in power9
powerpc/perf: Fix perf_get_data_addr() for power9 DD1
powerpc/boot: Fix zImage TOC alignment
The required changes in the function vxlan_dev_create() were missing
in commit 8bcdc4f3a2.
The vxlan device is not registered anymore after this patch and the error
path causes an stack dump:
WARNING: CPU: 3 PID: 1498 at net/core/dev.c:6713 rollback_registered_many+0x9d/0x3f0
Fixes: 8bcdc4f3a2 ("vxlan: add changelink support")
CC: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous idea was to check whether a net namespace is in
net_exit_list or not. It doesn't work, because net->exit_list is used in
__register_pernet_operations and __unregister_pernet_operations where
all namespaces are added to a temporary list to make cleanup in a error
case, so list_empty(&net->exit_list) always returns false.
Reported-by: Mantas Mikulėnas <grawity@gmail.com>
Fixes: 002d8a1a6c ("net: skip genenerating uevents for network namespaces that are exiting")
Signed-off-by: Andrei Vagin <avagin@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Asus fixes for the airplane LED and a long awaited fujitsu cleanup.
asus-wmi:
- Remove quirk_no_rfkill
- Detect quirk_no_rfkill from the DSDT
fujitsu-laptop:
- remove redundant MODULE_ALIAS entries
- autodetect LCD interface on all models
- simplify acpi_bus_register_driver() error handling
- remove redundant forward declarations
- replace numeric values with constants
- rename FUNC_RFKILL to FUNC_FLAGS
- make platform-related variables match naming convention
- replace "hotkey" with "laptop" in symbol names
- clearly denote backlight-related symbols
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYxd7oAAoJEKbMaAwKp364fokH+gNPpBgroix+sYnII3me24PM
1XfhSe7dHtLZVBUiGcK+kik4n9yQVdRZUNkrocc8yxINbpVVW+Wf22BXm7g81xyr
I+HNKKME8nlsTnG6znNJ/INITwKYsoV7mfx5aqLmsZjYpscqyU/A33J/2cIMrenk
I8J/svO3+Gk0sk+stPv7tofci+RkE7965JFBUeZUbQ13xVrw9GiPYiSHxpB6EldZ
qiBnmJOLgxRAvyggqX5jfXD9vl5jy9xEwQSw0emzhlTqs5QLlZjQkpKnSwbpnLQg
u3bt+oM2sp6cnkrCJ7VL+07GCAv31inBjeZRyZalU2b8/yPQdZ42mISIVidUiec=
=VO8n
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v4.11-2' of git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver updates from Darren Hart:
"Asus fixes for the airplane LED and a long awaited fujitsu cleanup.
asus-wmi:
- Remove quirk_no_rfkill
- Detect quirk_no_rfkill from the DSDT
fujitsu-laptop:
- remove redundant MODULE_ALIAS entries
- autodetect LCD interface on all models
- simplify acpi_bus_register_driver() error handling
- remove redundant forward declarations
- replace numeric values with constants
- rename FUNC_RFKILL to FUNC_FLAGS
- make platform-related variables match naming convention
- replace "hotkey" with "laptop" in symbol names
- clearly denote backlight-related symbols"
* tag 'platform-drivers-x86-v4.11-2' of git://git.infradead.org/linux-platform-drivers-x86:
platform/x86: asus-wmi: Remove quirk_no_rfkill
platform/x86: asus-wmi: Detect quirk_no_rfkill from the DSDT
platform/x86: fujitsu-laptop: remove redundant MODULE_ALIAS entries
platform/x86: fujitsu-laptop: autodetect LCD interface on all models
platform/x86: fujitsu-laptop: simplify acpi_bus_register_driver() error handling
platform/x86: fujitsu-laptop: remove redundant forward declarations
platform/x86: fujitsu-laptop: replace numeric values with constants
platform/x86: fujitsu-laptop: rename FUNC_RFKILL to FUNC_FLAGS
platform/x86: fujitsu-laptop: make platform-related variables match naming convention
platform/x86: fujitsu-laptop: replace "hotkey" with "laptop" in symbol names
platform/x86: fujitsu-laptop: clearly denote backlight-related symbols
Andreas reports kernel oops during rmmod of the br_netfilter module.
Hannes debugged the oops down to a NULL rt6info->rt6i_indev.
Problem is that br_netfilter has the nasty concept of adding a fake
rtable to skb->dst; this happens in a br_netfilter prerouting hook.
A second hook (in bridge LOCAL_IN) is supposed to remove these again
before the skb is handed up the stack.
However, on module unload hooks get unregistered which means an
skb could traverse the prerouting hook that attaches the fake_rtable,
while the 'fake rtable remove' hook gets removed from the hooklist
immediately after.
Fixes: 34666d467c ("netfilter: bridge: move br_netfilter out of the core")
Reported-by: Andreas Karis <akaris@redhat.com>
Debugged-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip6_fragment, in case skb has a fraglist, checks if the
skb is cloned. If it is, it will move to the 'slow path' and allocates
new skbs for each fragment.
However, right before entering the slowpath loop, it updates the
nexthdr value of the last ipv6 extension header to NEXTHDR_FRAGMENT,
to account for the fragment header that will be inserted in the new
ipv6-fragment skbs.
In case original skb is cloned this munges nexthdr value of another
skb. Avoid this by doing the nexthdr update for each of the new fragment
skbs separately.
This was observed with tcpdump on a bridge device where netfilter ipv6
reassembly is active: tcpdump shows malformed fragment headers as
the l4 header (icmpv6, tcp, etc). is decoded as a fragment header.
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Reported-by: Andreas Karis <akaris@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory beyond the endpoint array should a
malicious device lack the expected endpoints.
The endpoints are specifically dereferenced in the i2400m_bootrom_init
path during probe (e.g. in i2400mu_tx_bulk_out).
Fixes: f398e4240f ("i2400m/USB: probe/disconnect, dev init/shutdown
and reset backends")
Cc: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.
Fixes: cf7776dc05 ("[PATCH] isdn4linux: Siemens Gigaset drivers -
direct USB connection")
Cc: stable <stable@vger.kernel.org> # 2.6.17
Cc: Hansjoerg Lipp <hjlipp@web.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 2759647247 ("ipv6: fix ECMP route replacement") introduced a
loop that removes all siblings of an ECMP route that is being
replaced. However, this loop doesn't stop when it has replaced
siblings, and keeps removing other routes with a higher metric.
We also end up triggering the WARN_ON after the loop, because after
this nsiblings < 0.
Instead, stop the loop when we have taken care of all routes with the
same metric as the route being replaced.
Reproducer:
===========
#!/bin/sh
ip netns add ns1
ip netns add ns2
ip -net ns1 link set lo up
for x in 0 1 2 ; do
ip link add veth$x netns ns2 type veth peer name eth$x netns ns1
ip -net ns1 link set eth$x up
ip -net ns2 link set veth$x up
done
ip -net ns1 -6 r a 2000::/64 nexthop via fe80::0 dev eth0 \
nexthop via fe80::1 dev eth1 nexthop via fe80::2 dev eth2
ip -net ns1 -6 r a 2000::/64 via fe80::42 dev eth0 metric 256
ip -net ns1 -6 r a 2000::/64 via fe80::43 dev eth0 metric 2048
echo "before replace, 3 routes"
ip -net ns1 -6 r | grep -v '^fe80\|^ff00'
echo
ip -net ns1 -6 r c 2000::/64 nexthop via fe80::4 dev eth0 \
nexthop via fe80::5 dev eth1 nexthop via fe80::6 dev eth2
echo "after replace, only 2 routes, metric 2048 is gone"
ip -net ns1 -6 r | grep -v '^fe80\|^ff00'
Fixes: 2759647247 ("ipv6: fix ECMP route replacement")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
gup_p4d_range() should call gup_pud_range(), not itself.
[ This was not noticed on x86: this is the HAVE_GENERIC_RCU_GUP code
used by arm[64] and powerpc - Linus ]
Fixes: c2febafc67 ("mm: convert generic code to 5-level paging")
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reported-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reported-by: Anton Blanchard <anton@samba.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Improve bpf_{prog,jit_binary}_{un,}lock_ro() by throwing a
one-time warning in case of an error when the image couldn't
be set read-only, and also mark struct bpf_prog as locked when
bpf_prog_lock_ro() was called.
Reason for the latter is that bpf_prog_unlock_ro() is called from
various places including error paths, and we shouldn't mess with
page attributes when really not needed.
For bpf_jit_binary_unlock_ro() this is not needed as jited flag
implicitly indicates this, thus for archs with ARCH_HAS_SET_MEMORY
we're guaranteed to have a previously locked image. Overall, this
should also help us to identify any further potential issues with
set_memory_*() helpers.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent merge of 'linux-kselftest-4.11-rc1' tree broke bpf test build.
None of the tests were building and test_verifier.c had tons of compiler errors.
Fix it and add #ifdef CAP_IS_SUPPORTED to support old versions of libcap.
Tested on centos 6.8 and 7
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multipath routes can be rendered usesless when a device in one of the
paths is deleted. For example:
$ ip -f mpls ro ls
100
nexthop as to 200 via inet 172.16.2.2 dev virt12
nexthop as to 300 via inet 172.16.3.2 dev br0
101
nexthop as to 201 via inet6 2000:2::2 dev virt12
nexthop as to 301 via inet6 2000:3::2 dev br0
$ ip li del br0
When br0 is deleted the other hop is not considered in
mpls_select_multipath because of the alive check -- rt_nhn_alive
is 0.
rt_nhn_alive is decremented once in mpls_ifdown when the device is taken
down (NETDEV_DOWN) and again when it is deleted (NETDEV_UNREGISTER). For
a 2 hop route, deleting one device drops the alive count to 0. Since
devices are taken down before unregistering, the decrement on
NETDEV_UNREGISTER is redundant.
Fixes: c89359a42e ("mpls: support for dead routes")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases during XenBus disconnect event handling and subsequent
queue resource release there may be some TX handlers active on
other processors. Use RCU in order to synchronize with them.
Signed-off-by: Igor Druzhinin <igor.druzhinin@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the mpls_router module is unloaded, mpls routes are deleted but
notifications are not sent to userspace leaving userspace caches
out of sync. Add the call to mpls_notify_route in mpls_net_exit as
routes are freed.
Fixes: 0189197f44 ("mpls: Basic routing support")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It wasn't clear if the 'forwarding' setting needs to be enabled on the
interface that packets are received from, or on the interface that
packets are forwarded to, or both.
In fact (according to my code reading) the setting is relevant on the
interface that packets are received from, so this change updates the doc
to say that.
Signed-off-by: Neil Jerram <neil@tigera.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the send indirection table from the inner device (netvsc)
to the network device context.
It is possible that netvsc_device is not present (remove in progress).
This solves potential use after free issues when packet is being
created during MTU change, shutdown, or queue count changes.
Fixes: d8e18ee0fa ("netvsc: enhance transmit select_queue")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a network interface controlled by the aquantia ethernet driver is brought
down a warning is output in dmesg (see below).
The problem is that aq_pci_func_free_irqs() is calling free_irq() before it is
calling irq_set_affinity_hint().
WARNING: CPU: 4 PID: 10068 at kernel/irq/manage.c:1503 __free_irq+0x24d/0x2b0
<snip>
Call Trace:
dump_stack+0x63/0x87
__warn+0xd1/0xf0
warn_slowpath_null+0x1d/0x20
__free_irq+0x24d/0x2b0
free_irq+0x39/0x90
aq_pci_func_free_irqs+0x52/0xa0 [atlantic]
aq_nic_stop+0xca/0xd0 [atlantic]
aq_ndev_close+0x1d/0x40 [atlantic]
__dev_close_many+0x99/0x100
__dev_close+0x67/0xb0
<snip>
Fixes: 36a4a50f40 ("net: ethernet: aquantia: switch to pci_alloc_irq_vectors")
Cc: Christoph Hellwig <hch@lst.de>
Cc: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David Arcari <darcari@redhat.com>
Tested-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the detection introduced in the previous patches, we don't need
these static DMI-based quirks anymore.
This reverts the following commits:
56a37a7200 "asus-wmi: Add quirk_no_rfkill_wapf4 for the Asus X456UA"
a961a285b4 "asus-wmi: Add quirk_no_rfkill_wapf4 for the Asus X456UF"
6b7ff2af52 "asus-wmi: Add quirk_no_rfkill for the Asus Z550MA"
02db9ff7af "asus-wmi: Add quirk_no_rfkill for the Asus U303LB"
2d735244b7 "asus-wmi: Add quirk_no_rfkill for the Asus N552VW"
a977e59c0c "asus-wmi: Create quirk for airplane_mode LED"
Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[dvhart: minor commit message corrections]
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Pull s390 fixes from Martin Schwidefsky:
- four patches to get the new cputime code in shape for s390
- add the new statx system call
- a few bug fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: wire up statx system call
KVM: s390: Fix guest migration for huge guests resulting in panic
s390/ipl: always use load normal for CCW-type re-IPL
s390/timex: micro optimization for tod_to_ns
s390/cputime: provide archicture specific cputime_to_nsecs
s390/cputime: reset all accounting fields on fork
s390/cputime: remove last traces of cputime_t
s390: fix in-kernel program checks
s390/crypt: fix missing unlock in ctr_paes_crypt on error path
Pull x86 fixes from Thomas Gleixner:
- a fix for the kexec/purgatory regression which was introduced in the
merge window via an innocent sparse fix. We could have reverted that
commit, but on deeper inspection it turned out that the whole
machinery is neither documented nor robust. So a proper cleanup was
done instead
- the fix for the TLB flush issue which was discovered recently
- a simple typo fix for a reboot quirk
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/tlb: Fix tlb flushing when lguest clears PGE
kexec, x86/purgatory: Unbreak it and clean it up
x86/reboot/quirks: Fix typo in ASUS EeeBook X205TA reboot quirk
Pull irq fixes from Thomas Gleixner:
- a workaround for a GIC erratum
- a missing stub function for CONFIG_IRQDOMAIN=n
- fixes for a couple of type inconsistencies
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/crossbar: Fix incorrect type of register size
irqchip/gicv3-its: Add workaround for QDF2400 ITS erratum 0065
irqdomain: Add empty irq_domain_check_msi_remap
irqchip/crossbar: Fix incorrect type of local variables
Fengguang reported random corruptions from various locations on x86-32
after commits d2852a2240 ("arch: add ARCH_HAS_SET_MEMORY config") and
9d876e79df ("bpf: fix unlocking of jited image when module ronx not set")
that uses the former. While x86-32 doesn't have a JIT like x86_64, the
bpf_prog_lock_ro() and bpf_prog_unlock_ro() got enabled due to
ARCH_HAS_SET_MEMORY, whereas Fengguang's test kernel doesn't have module
support built in and therefore never had the DEBUG_SET_MODULE_RONX setting
enabled.
After investigating the crashes further, it turned out that using
set_memory_ro() and set_memory_rw() didn't have the desired effect, for
example, setting the pages as read-only on x86-32 would still let
probe_kernel_write() succeed without error. This behavior would manifest
itself in situations where the vmalloc'ed buffer was accessed prior to
set_memory_*() such as in case of bpf_prog_alloc(). In cases where it
wasn't, the page attribute changes seemed to have taken effect, leading to
the conclusion that a TLB invalidate didn't happen. Moreover, it turned out
that this issue reproduced with qemu in "-cpu kvm64" mode, but not for
"-cpu host". When the issue occurs, change_page_attr_set_clr() did trigger
a TLB flush as expected via __flush_tlb_all() through cpa_flush_range(),
though.
There are 3 variants for issuing a TLB flush: invpcid_flush_all() (depends
on CPU feature bits X86_FEATURE_INVPCID, X86_FEATURE_PGE), cr4 based flush
(depends on X86_FEATURE_PGE), and cr3 based flush. For "-cpu host" case in
my setup, the flush used invpcid_flush_all() variant, whereas for "-cpu
kvm64", the flush was cr4 based. Switching the kvm64 case to cr3 manually
worked fine, and further investigating the cr4 one turned out that
X86_CR4_PGE bit was not set in cr4 register, meaning the
__native_flush_tlb_global_irq_disabled() wrote cr4 twice with the same
value instead of clearing X86_CR4_PGE in the first write to trigger the
flush.
It turned out that X86_CR4_PGE was cleared from cr4 during init from
lguest_arch_host_init() via adjust_pge(). The X86_FEATURE_PGE bit is also
cleared from there due to concerns of using PGE in guest kernel that can
lead to hard to trace bugs (see bff672e630 ("lguest: documentation V:
Host") in init()). The CPU feature bits are cleared in dynamic
boot_cpu_data, but they never propagated to __flush_tlb_all() as it uses
static_cpu_has() instead of boot_cpu_has() for testing which variant of TLB
flushing to use, meaning they still used the old setting of the host
kernel.
Clearing via setup_clear_cpu_cap(X86_FEATURE_PGE) so this would propagate
to static_cpu_has() checks is too late at this point as sections have been
patched already, so for now, it seems reasonable to switch back to
boot_cpu_has(X86_FEATURE_PGE) as it was prior to commit c109bf9599
("x86/cpufeature: Remove cpu_has_pge"). This lets the TLB flush trigger via
cr3 as originally intended, properly makes the new page attributes visible
and thus fixes the crashes seen by Fengguang.
Fixes: c109bf9599 ("x86/cpufeature: Remove cpu_has_pge")
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: bp@suse.de
Cc: Kees Cook <keescook@chromium.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: lkp@01.org
Cc: Laura Abbott <labbott@redhat.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernrl.org/r/20170301125426.l4nf65rx4wahohyl@wfg-t540p.sh.intel.com
Link: http://lkml.kernel.org/r/25c41ad9eca164be4db9ad84f768965b7eb19d9e.1489191673.git.daniel@iogearbox.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
ARM updates from Marc Zyngier:
"vgic updates:
- Honour disabling the ITS
- Don't deadlock when deactivating own interrupts via MMIO
- Correctly expose the lact of IRQ/FIQ bypass on GICv3
I/O virtualization:
- Make KVM_CAP_NR_MEMSLOTS big enough for large guests with
many PCIe devices
General bug fixes:
- Gracefully handle exception generated with syndroms that
the host doesn't understand
- Properly invalidate TLBs on VHE systems"
x86:
- improvements in emulation of VMCLEAR, VMX MSR bitmaps, and VCPU reset
-----BEGIN PGP SIGNATURE-----
iQEcBAABCAAGBQJYxENfAAoJEED/6hsPKofoEEkIAIWglnOGOHqf4pPv9OThKzKm
5CGINdPVEkJ56QNaYrINiQRHAzIUg8dsrhsisYmEdYGv3Mxf5WO0OebfzTrniNm4
GXIM8OuYD04MSnIomfGGBAwFZ6ptgdeD+PVkSFYHArkvWYfPm54ghjVj3AXmkicf
tRiIsPSiL/QT0vha5LBGfwsWOYavmZRfQBNA5yYUIHgO0Mp7LI24AeZOQiSM2ngx
Gl5xfzk0bayhZSBr+r/fvxqbEd0udiY7klGEvt3hrPT+JzzpoamEgCCZ6eLFZbGM
eABeQUzm7StD4Ib3WHkVU81ysOWndL0TK94BBBLIn1j+ht9FLi9iGkmTYspk9po=
=/phS
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Radim Krčmář:
"ARM updates from Marc Zyngier:
- vgic updates:
- Honour disabling the ITS
- Don't deadlock when deactivating own interrupts via MMIO
- Correctly expose the lact of IRQ/FIQ bypass on GICv3
- I/O virtualization:
- Make KVM_CAP_NR_MEMSLOTS big enough for large guests with many
PCIe devices
- General bug fixes:
- Gracefully handle exception generated with syndroms that the host
doesn't understand
- Properly invalidate TLBs on VHE systems
x86:
- improvements in emulation of VMCLEAR, VMX MSR bitmaps, and VCPU
reset
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: nVMX: do not warn when MSR bitmap address is not backed
KVM: arm64: Increase number of user memslots to 512
KVM: arm/arm64: Remove KVM_PRIVATE_MEM_SLOTS definition that are unused
KVM: arm/arm64: Enable KVM_CAP_NR_MEMSLOTS on arm/arm64
KVM: Add documentation for KVM_CAP_NR_MEMSLOTS
KVM: arm/arm64: VGIC: Fix command handling while ITS being disabled
arm64: KVM: Survive unknown traps from guests
arm: KVM: Survive unknown traps from guests
KVM: arm/arm64: Let vcpu thread modify its own active state
KVM: nVMX: reset nested_run_pending if the vCPU is going to be reset
kvm: nVMX: VMCLEAR should not cause the vCPU to shut down
KVM: arm/arm64: vgic-v3: Don't pretend to support IRQ/FIQ bypass
arm64: KVM: VHE: Clear HCR_TGE when invalidating guest TLBs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=khtX
-----END PGP SIGNATURE-----
Merge tag 'extable-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
Pull extable.h fix from Paul Gortmaker:
"Fixup for arch/score after extable.h introduction.
It seems that Guenter is the only one on the planet doing builds for
arch/score -- we don't have compile coverage for it in linux-next or
in the kbuild-bot either. Guenter couldn't even recall where he got
his toolchain, but was kind enough to share it with me so I could
validate this change and also add arch/score to my build coverage.
I sat on this a bit in case there was any other fallout in other arch
dirs, but since this still seems to be the only one, I might as well
send it on its way"
* tag 'extable-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
score: Fix implicit includes now failing build after extable change
getrandom(2). It's faster and arguably more secure than cut-down MD5
that we had been using.
Also do some code cleanup.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEK2m5VNv+CHkogTfJ8vlZVpUNgaMFAljCENEACgkQ8vlZVpUN
gaP8lwf7BFtF52mKQcsVYxxZtRPH5dQwJCh3rohQ0WEJi5hHyZPZNz24dPHgc8Xl
GDq7v7o10dL3aeK6P51lYNcDb9xwYakCXm5sw46c5juca/VAVaxHb/kSDPSPUCNj
7n7mNSM61UhYAN10AXi9FGJo/Rdr0U5F1VfoWVYqaHYsItYLCjlSk6ob7vKxCPUd
458qaGBvK8luwQgFPQftJ20j81zXNuRe5JHjCQ2LtaRWM8kNI/wmyNSokD73BkZl
k8B7VqG4YpKp+4xgThp12GpXHrKB9kzQfmM4dZQQiGai9Ni59+iNqEcumv0Jb5MG
gY/m5Wc1Q45/5FosPXQYHzMPHrSJ3A==
=g1OD
-----END PGP SIGNATURE-----
Merge tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull random updates from Ted Ts'o:
"Change get_random_{int,log} to use the CRNG used by /dev/urandom and
getrandom(2). It's faster and arguably more secure than cut-down MD5
that we had been using.
Also do some code cleanup"
* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
random: move random_min_urandom_seed into CONFIG_SYSCTL ifdef block
random: convert get_random_int/long into get_random_u32/u64
random: use chacha20 for get_random_int/long
random: fix comment for unused random_min_urandom_seed
random: remove variable limit
random: remove stale urandom_init_wait
random: remove stale maybe_reseed_primary_crng
After changing from module.h to extable.h, score builds fail with:
arch/score/kernel/traps.c: In function 'do_ri':
arch/score/kernel/traps.c:248:4: error: implicit declaration of function 'user_disable_single_step'
arch/score/mm/extable.c: In function 'fixup_exception':
arch/score/mm/extable.c:32:38: error: dereferencing pointer to incomplete type
arch/score/mm/extable.c:34:24: error: dereferencing pointer to incomplete type
because extable.h doesn't drag in the same amount of headers as the
module.h did. Add in the headers which were implicitly expected.
Fixes: 90858794c9 ("module.h: remove extable.h include now users have migrated")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
[PG: tweak commit log; refresh for sched header refactoring.]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Linus Torvalds