Add the missing iounmap() before return from omap1_system_dma_init()
in the error handling case.
Also removed platform_device_del() on add resources error case which
cause dup device delete.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If DEBUG_LL and earlyprintk are enabled, and omap-serial.c is compiled
as a module, the kernel boot hangs early as the clocks for serial port
are cut while earlyprintk still uses the port.
The problem is a race between the late_initcall for omap_device (which
idles devices that have no drivers) and the late_initcall in
kernel/printk.c which turns off the earlyconsole. Any printks
that happen between this omap_device late initcall and the earlyconsole
late initcall will crash when accessing the UART.
The fix is to ensure the omap_device initcall happens after the
earlyconsole initcall.
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 9fdca9df (spi: omap2-mcspi: convert to module_platform_driver)
broke the SPI display/panel driver probe on RX-51/N900. The exact cause is
not fully understood, but it seems to be related to the probe order. SPI
communication to the panel driver (spi1.2) fails unless the touchscreen
(spi1.0) has been probed/initialized before. When the omap2-mcspi driver
was converted to a platform driver, it resulted in that the devices are
probed immediately after the board registers them in the order they are
listed in the board file.
Fix the issue by moving the touchscreen before the panel in the SPI
device list.
The patch fixes the following failure:
[ 1.260955] acx565akm spi1.2: invalid display ID
[ 1.265899] panel-acx565akm display0: acx_panel_probe panel detect error
[ 1.273071] omapdss CORE error: driver probe failed: -19
Tested-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Joni Lapilainen <joni.lapilainen@gmail.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
On Beagle xM Rev. Ax/Bx, the USB power enable GPIO logic is
reversed when compared to other revisions i.e. it is
active high instead of active low.
Use the beagle_config.usb_pwr_level flag correctly so that
the power regulator can be configured at runtime.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
specifics (the 'gic' branch merged), it can be enabled on arm64.
- Enable arm64 support for poweroff/restart (for code under
drivers/power/reset/).
- Fixes (dts file, exception handling, bitops)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.9 (GNU/Linux)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=qd94
-----END PGP SIGNATURE-----
Merge tag 'arm64-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64
Pull arm64 update from Catalin Marinas:
- Since drivers/irqchip/irq-gic.c no longer has dependencies on arm32
specifics (the 'gic' branch merged), it can be enabled on arm64.
- Enable arm64 support for poweroff/restart (for code under
drivers/power/reset/).
- Fixes (dts file, exception handling, bitops)
* tag 'arm64-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64:
arm64: Treat the bitops index argument as an 'int'
arm64: Ignore the 'write' ESR flag on cache maintenance faults
arm64: dts: fix #address-cells for foundation-v8
arm64: vexpress: Add support for poweroff/restart
arm64: Enable support for the ARM GIC interrupt controller
Pull Hexagon fixes from Richard Kuo:
"A bug fix and a Kconfig cleanup"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rkuo/linux-hexagon-kernel:
HEXAGON: Remove non existent reference to GENERIC_KERNEL_EXECVE & GENERIC_KERNEL_THREAD
Hexagon: fix register used to call do_work_pending
Commit ff5c9059 (ARM: dts: OMAP3+: Correct gpio #interrupts-cells
property) updated the number of interrupt cells required for configuring
gpios as interrupts for other devices (such as ethernet controllers).
This update allowed the interrupt type (edge, level, etc) to be
configured via device-tree (as described in the
Documentation/devicetree/bindings/gpio/gpio-omap.txt).
This broke ethernet support on the OMAP4 SDP board that defines a gpio
as the ethernet IRQ because the interrupt type (level, edge, etc) was
not getting configured correctly. This board use the ks8851 ethernet
chip which has an active low interrupt. Fix this by defining the gpio
interrupt as active-low in the device-tree binding.
Please note that the OMAP4-VAR-SOM also uses the same ethernet
controller and it is expected it will have the same problem. So the
same fix is also applied to this board.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
During review of git commit cb9c6f15f3
("xen/spinlock: Check against default value of -1 for IRQ line.")
Stefano pointed out a bug in the patch. Unfortunatly due to vacation
timing the fix was not applied and this patch fixes it up.
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
As it will point to some data, but not event channel data (the
shared_info has an array limited to 32).
This means that for PVHVM guests with more than 32 VCPUs without
the usage of VCPUOP_register_info any interrupts to VCPUs
larger than 32 would have gone unnoticed during early bootup.
That is OK, as during early bootup, in smp_init we end up calling
the hotplug mechanism (xen_hvm_cpu_notify) which makes the
VCPUOP_register_vcpu_info call for all VCPUs and we can receive
interrupts on VCPUs 33 and further.
This is just a cleanup.
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Changes for pure microMIPS cores to dynamically determine the ASID
size at boot time.
Includes bug fix https://patchwork.linux-mips.org/patch/5230/
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Original patch by Ralf Baechle and removed by Harold Koerfgen
with commit f67e4ffc79905482c3b9b8c8dd65197bac7eb508. This
allows for more generic kernels since the size of the ASID
and corresponding masks can be determined at run-time. This
patch is also required for the new Aptiv cores and has been
tested on Malta and Malta Aptiv platforms.
[ralf@linux-mips.org: Added relevant part of fix
https://patchwork.linux-mips.org/patch/5213/]
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove 'arch/mips/include/asm/mips-boards/prom.h' and get rid of
all inclusions of it by Malta and SEAD-3 platforms.
[ralf@linux-mips.org: Fold in John Crispin <blogic@openwrt.org>'s "MIPS:
ar7 powertv build"].
[ralf@linux-mips.org: Fold in John Crispin <blogic@openwrt.org>'s "MIPS:
unbreak powertv build"].
[ralf@linux-mips.org: Test. Build. Your. Fscking. Code. Or...]
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Add parsing of the environment and command line variables passed to
the kernel to the firmware library.
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Add declaration of 'mips_scroll_message' and 'mips_display_message'
to the common generic header file for the MIPS Technologies Inc.
development boards.
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Setting the LED_CORE_SUSPENDRESUME flag causes the LED driver core to call
led_classdev_suspend/led_classdev_resume during suspend/resume. Since this is
exactly what the driver's custom suspend/resume callbacks do we can replace them
by setting the LED_CORE_SUSPENDRESUME flag.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Emulation of xcr0 writes zero guest_xcr0_loaded variable so that
subsequent VM-entry reloads CPU's xcr0 with guests xcr0 value.
However, this is incorrect because guest_xcr0_loaded variable is
read to decide whether to reload hosts xcr0.
In case the vcpu thread is scheduled out after the guest_xcr0_loaded = 0
assignment, and scheduler decides to preload FPU:
switch_to
{
__switch_to
__math_state_restore
restore_fpu_checking
fpu_restore_checking
if (use_xsave())
fpu_xrstor_checking
xrstor64 with CPU's xcr0 == guests xcr0
Fix by properly restoring hosts xcr0 during emulation of xcr0 writes.
Analyzed-by: Ulrich Obergfell <uobergfe@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
The bitops prototype use an 'int' as the bit index type but the asm
implementation assume it to be a 'long'. Since the compiler does not
guarantee zeroing the upper 32-bits in a register when used as 'int',
change the bitops implementation accordingly.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
ESR.WnR bit is always set on data cache maintenance faults even though
the page is not required to have write permission. If a translation
fault (page not yet mapped) happens for read-only user address range,
Linux incorrectly assumes a permission fault. This patch adds the check
of the ESR.CM bit during the page fault handling to ignore the 'write'
flag.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Tim Northover <Tim.Northover@arm.com>
Cc: stable@vger.kernel.org
Commit 90556ca1 ("arm64: vexpress: Add dts files for the ARMv8 RTSM
models") added foundation-v8.dts, but erroneously set
/cpus/#address-cells = <1> while providing two cells in each cpus/cpu@N
node's reg property.
As of commit ea393a2e ("arm64: smp: honour #address-size when parsing
CPU reg property") we read in as many address cells as specified rather
than always reading two. This means that for foundation-v8.dts, we only
read the first reg cell (zero) for each cpu node, and receive a lot of
warnings at boot of the form "/cpus/cpu@1: duplicate cpu reg properties
in the DT".
This patch corrects foundation-v8.dts to have the correct value for
/cpus/#address-cells.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch adds the arm_pm_poweroff definition expected by the
vexpress-poweroff.c driver and enables the latter for arm64.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Pawel Moll <pawel.moll@arm.com>
* arm64-prep-gic:
irqchip: gic: Perform the gic_secondary_init() call via CPU notifier
irqchip: gic: Call handle_bad_irq() directly
arm: Move chained_irq_(enter|exit) to a generic file
arm: Move the set_handle_irq and handle_arch_irq declarations to asm/irq.h
If the firmware returns an error such as "closed" (or hardware
error), we should drop characters.
Currently we only do that when a firmware compatible with OPAL v2
APIs is detected, in the code that calls opal_console_write_buffer_space(),
which didn't exist with OPAL v1 (or didn't work).
However, when enabling early debug consoles, the flag indicating
that v2 is supported isn't set yet, causing us, in case of errors
or closed console, to spin forever.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Merge more incoming from Andrew Morton:
- Various fixes which were stalled or which I picked up recently
- A large rotorooting of the AIO code. Allegedly to improve
performance but I don't really have good performance numbers (I might
have lost the email) and I can't raise Kent today. I held this out
of 3.9 and we could give it another cycle if it's all too late/scary.
I ended up taking only the first two thirds of the AIO rotorooting. I
left the percpu parts and the batch completion for later. - Linus
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (33 commits)
aio: don't include aio.h in sched.h
aio: kill ki_retry
aio: kill ki_key
aio: give shared kioctx fields their own cachelines
aio: kill struct aio_ring_info
aio: kill batch allocation
aio: change reqs_active to include unreaped completions
aio: use cancellation list lazily
aio: use flush_dcache_page()
aio: make aio_read_evt() more efficient, convert to hrtimers
wait: add wait_event_hrtimeout()
aio: refcounting cleanup
aio: make aio_put_req() lockless
aio: do fget() after aio_get_req()
aio: dprintk() -> pr_debug()
aio: move private stuff out of aio.h
aio: add kiocb_cancel()
aio: kill return value of aio_complete()
char: add aio_{read,write} to /dev/{null,zero}
aio: remove retry-based AIO
...
- Note that this file is statically linked with the rest of the host kernel (KSEG0). This is because kernel modules are
loaded into mapped space on MIPS and we want to make sure that we don't get any host kernel TLB faults while
manipulating TLBs.
- Virtual Guest TLBs are implemented as 64 entry array regardless of the number of host TLB entries.
- Shadow TLBs map Guest virtual addresses to Host physical addresses.
- TLB miss handling details:
Guest KSEG0 TLBMISS (0x40000000 – 0x60000000): Transparent to the Guest.
Guest KSEG2/3 (0x60000000 – 0x80000000) & Guest UM TLBMISS (0x00000000 – 0x40000000)
Lookup in Guest/Virtual TLB
If an entry doesn’t match
deliver appropriate TLBMISS LD/ST exception to the guest
If entry does exist in the Guest TLB and is NOT Valid
Deliver TLB invalid exception to the guest
If entry does exist in the Guest TLB and is VALID
Inject the TLB entry into the Shadow TLB
Signed-off-by: Sanjay Lal <sanjayl@kymasys.com>
Cc: kvm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
- The Guest kernel is run in UM and privileged instructions cause a trap.
- If the instruction causing the trap is in a branch delay slot, the branch
needs to be emulated to figure out the PC @ which the guest will resume
execution.
Signed-off-by: Sanjay Lal <sanjayl@kymasys.com>
Cc: kvm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
- Implements the arch specific APIs for KVM, some are stubs for MIPS
- kvm_mips_handle_exit(): Main 'C' distpatch routine for handling exceptions while in "Guest" mode.
- Also implements in-kernel timer interrupt support for the guest.
Signed-off-by: Sanjay Lal <sanjayl@kymasys.com>
Cc: kvm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
- __kvm_mips_vcpu_run: main entry point to enter guest, we save kernel context, load
up guest context from and ERET to guest context.
- mips32_exception: L1 exception handler(s), save k0/k1 and jump to main handlers.
- mips32_GuestException: Generic exception handlers for exceptions/interrupts while in
guest context. Save guest context, restore some kernel context and jump to
main 'C' handler: kvm_mips_handle_exit()
Signed-off-by: Sanjay Lal <sanjayl@kymasys.com>
Cc: kvm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
- Add the KVM option to MIPS build files.
- Add default config files for KVM host/guest kernels.
- Change the link address for the Malta KVM Guest kernel to UM (0x40100000).
- Add KVM Kconfig file with KVM/MIPS specific options
Signed-off-by: Sanjay Lal <sanjayl@kymasys.com>
Cc: kvm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In the Linux kernel traditionally pfns are represented by an unsigned long.
However a few bits of the SGI IP27 platform code that were ported from
IRIX are using pfn_t for historic reasons. This is conflicting with
KVM's use of pfn_t.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use common help functions to free reserved pages.
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I badly screwed up the merge in commit 6fa52ed33b ("Merge tag
'drivers-for-linus' of git://git.kernel.org/pub/.../arm-soc") by
incorrectly taking the arch/arm/mach-omap2/* data fully from the merge
target because the 'drivers-for-linus' branch seemed to be a proper
superset of the duplicate ARM commits.
That was bogus: commit ff931c821b ("ARM: OMAP: clocks: Delay clk inits
atleast until slab is initialized") only existed in head, and the
changes to arch/arm/mach-omap2/timer.c from that commit got list.
Re-doing the merge more carefully, I do think this part was the only
thing I screwed up. Knock wood.
Reported-by: Tony Lindgren <tony@atomide.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add some mosty unused, but missing clocks for BCM6328 and BCM6362.
This also fixes PCIe init on BCM6362.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5200/
Acked-by: John Crispin <blogic@openwrt.org>
There is now a generic function for detecting memory size. Use this instead of
the one found in the ath79 support.
Signed-off-by: John Crispin <blogic@openwrt.org>
Acked-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5149/
Call detect_memory_region() from plat_mem_setup() unless the size was already
read from the system controller.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5184/
Populate struct soc_info with the data that describes our RAM window.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5183/
Populate struct soc_info with the data that describes our RAM window.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5182/
Populate struct soc_info with the data that describes our RAM window.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5181/
Populate struct soc_info with the data that describes our RAM window.
As memory detection fails on RT5350 we read the amount of available memory
from the system controller.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5180/
Depending on the actual SoC we have a different base address as well as minimum
and maximum size for RAM. Add these fields to the per SoC structure.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5179/
Add a generic way of detecting the available RAM. This function is based on the
implementation already used by ath79.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5178/
Add a dtsi file for MT7620A SoC and a sample dts file.
Signed-off-by: John Crispin <blogic@openwrt.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Patchwork: http://patchwork.linux-mips.org/patch/5190/
Add a dtsi file for RT3883 SoC and a sample dts file.
Signed-off-by: John Crispin <blogic@openwrt.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Patchwork: http://patchwork.linux-mips.org/patch/5189/
Add a dtsi file for RT2880 SoC and a sample dts file.
Signed-off-by: John Crispin <blogic@openwrt.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Patchwork: http://patchwork.linux-mips.org/patch/5188/
* remove nodes for cores whose drivers are not upstream yet
* add compat string for an additional soc
* fix a whitespace error
Signed-off-by: John Crispin <blogic@openwrt.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Patchwork: http://patchwork.linux-mips.org/patch/5186/
Add support code for mt7620 SOC.
The code detects the SoC and registers the clk / pinmux settings.
Signed-off-by: John Crispin <blogic@openwrt.org>
Acked-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5177/
Add support code for rt3883 SOC.
The code detects the SoC and registers the clk / pinmux settings.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5185/
Add support code for rt2880 SOC.
The code detects the SoC and registers the clk / pinmux settings.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5176/
Add a field for the uart muxing mask and set it inside the rt305x setup code.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5744/
This will be used for RT3662/RT3883.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5173/
These structures are exported via struct ralink_pinmux rt_gpio_pinmux and can
hence be static.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5172/
RT2880 has a different location for the early serial port.
Signed-off-by: John Crispin <blogic@openwrt.org>
Acked-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5170/
Add a few missing defines that are needed to make memory detection work on the
RT5350.
Signed-off-by: John Crispin <blogic@openwrt.org>
Acked-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5169/
Trivial patch that adds a comment that makes the code more readable.
Signed-off-by: John Crispin <blogic@openwrt.org>
Acked-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5168/
Add a few missing clocks.
Signed-off-by: John Crispin <blogic@openwrt.org>
Acked-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5167/
Add a few missing defines that are needed to make USB and clock detection work
on the RT3352.
Signed-off-by: John Crispin <blogic@openwrt.org>
Acked-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5166/
The Ralink IRQ code was not handling the PCI IRQ yet. Add this functionaility
to make PCI work on rt3883.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5165/
Previously this functionality was only available to users of the mips_machine
api. Moving the code to prom.c allows us to also add a OF wrapper.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5164/
Current GPIO chip implementation in octeon-irq is still broken, even after upstream
commit 87161ccdc6 (MIPS: Octeon: Fix broken interrupt
controller code). It works for GPIO IRQs that have reset-default configuration, but
not for edge-triggered ones.
The problem is in octeon_irq_gpio_map_common(), which passes modified "hw" variable
(which has range of possible values 16..31) as "gpio_line" parameter to
octeon_irq_set_ciu_mapping(), which saves it in private data of the IRQ chip. Later,
neither octeon_irq_gpio_setup() is able to re-configure GPIOs (cvmx_write_csr() is
writing to non-existent CVMX_GPIO_BIT_CFGX), nor octeon_irq_ciu_gpio_ack() is able
to acknowledge such IRQ, because "mask" is incorrect.
Fix is trivial and has been tested on Cavium Octeon II -based board, including
both level-triggered and edge-triggered GPIO IRQs.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin.ext@nsn.com>
Cc: David Daney <david.daney@cavium.com>
Acked-by: David Daney <david.daney@cavium.com>
Patchwork: http://patchwork.linux-mips.org/patch/4980/
Acked-by: John Crispin <blogic@openwrt.org>
Convert all uses of devm_request_and_ioremap() to the newly introduced
devm_ioremap_resource() which provides more consistent error handling.
Signed-off-by: Silviu-Mihai Popescu <silviupopescu1990@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/4986/
Acked-by: John Crispin <blogic@openwrt.org>
The operations on the bitmap pointers are protected by "memory"
clobbering raw_local_irq_{save,restore}(), so there is no need for
volatile here. By removing the volatile we get better code generation
out of the compiler.
Signed-off-by: David Daney <david.daney@cavium.com>
Patchwork: http://patchwork.linux-mips.org/patch/4966/
Acked-by: John Crispin <blogic@openwrt.org>
Currently, init_new_context() only for each online CPU, this may cause
memory corruption when CPU hotplug and fork() happens at the same time.
To avoid this, we make init_new_context() cover each possible CPU.
Scenario:
1, CPU#1 is being offline;
2, On CPU#0, do_fork() call dup_mm() and copy a mm_struct to the child;
3, On CPU#0, dup_mm() call init_new_context(), since CPU#1 is offline
and init_new_context() only covers the online CPUs, child has the
same asid as its parent on CPU#1 (however, child's asid should be 0);
4, CPU#1 is being online;
5, Now, if both parent and child run on CPU#1, memory corruption (e.g.
segfault, bus error, etc.) will occur.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Acked-by: David Daney <david.daney@cavium.com>
Patchwork: http://patchwork.linux-mips.org/patch/4995/
Acked-by: John Crispin <blogic@openwrt.org>
This and the next patch resolve memory corruption problems while CPU
hotplug. Without these patches, memory corruption can triggered easily
as below:
On a quad-core MIPS platform, use "spawn" of UnixBench-5.1.3 (http://
code.google.com/p/byte-unixbench/) and a CPU hotplug script like this
(hotplug.sh):
while true; do
echo 0 >/sys/devices/system/cpu/cpu1/online
echo 0 >/sys/devices/system/cpu/cpu2/online
echo 0 >/sys/devices/system/cpu/cpu3/online
sleep 1
echo 1 >/sys/devices/system/cpu/cpu1/online
echo 1 >/sys/devices/system/cpu/cpu2/online
echo 1 >/sys/devices/system/cpu/cpu3/online
sleep 1
done
Run "hotplug.sh" and then run "spawn 10000", spawn will get segfault
after a few minutes.
This patch:
Currently, clear_page()/copy_page() are generated by Micro-assembler
dynamically. But they are unavailable until uasm_resolve_relocs() has
finished because jump labels are illegal before that. Since these
functions are shared by every CPU, we only call build_clear_page()/
build_copy_page() only once at boot time. Without this patch, programs
will get random memory corruption (segmentation fault, bus error, etc.)
while CPU Hotplug (e.g. one CPU is using clear_page() while another is
generating it in cpu_cache_init()).
For similar reasons we modify build_tlb_refill_handler()'s invocation.
V2:
1, Rework the code to make CPU#0 can be online/offline.
2, Introduce cpu_has_local_ebase feature since some types of MIPS CPU
need a per-CPU tlb_refill_handler().
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Hongbing Hu <huhb@lemote.com>
Acked-by: David Daney <david.daney@cavium.com>
Patchwork: http://patchwork.linux-mips.org/patch/4994/
Acked-by: John Crispin <blogic@openwrt.org>
The Kconfig symbol MIPS_DISABLE_OBSOLETE_IDE was added in v2.6.10. It
has never been used. Let's remove it.
The symbol was originally introduced by the following commit
commit 2bfa662b64a7ee593f3039c1d3fd81a7766a63cd
Author: Pete Popov <ppopov@embeddedalley.com>
Date: Tue Oct 12 06:24:19 2004 +0000
- Db1550 bug fixes
- updated defconfig
- updated Kconfig to use DMA_COHERENT since new silicon is coherent
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Patchwork: http://patchwork.linux-mips.org/patch/5064/
Acked-by: John Crispin <blogic@openwrt.org>
The Kconfig symbol MIPS_BOARDS_GEN is unused since v2.6.27. It should
now be removed.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Patchwork: http://patchwork.linux-mips.org/patch/5063/
Acked-by: John Crispin <blogic@openwrt.org>
The support for PB1100, PB1500, and PB1550 got merged into the code for
DB1000 and DB1550 code in v3.7. When that was done the three related
Kconfig symbols were dropped. But not all related Kconfig macros were
removed. Do so now.
Note that the PB1100 code in the Au1100 LCD driver is removed entirely
and not converted to use its current Kconfig macro. That is done because
the macros it uses (PB1100_G_CONTROL, PB1100_G_CONTROL_BL, and
PB1100_G_CONTROL_VDD) are never defined. Actually only one of these was
ever defined (PB1100_G_CONTROL) but that define was removed in v2.6.34.
So, as far as I can tell, this code could have never compiled.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Patchwork: http://patchwork.linux-mips.org/patch/5040/
Acked-by: John Crispin <blogic@openwrt.org>
The commit c783390a0e [MIPS: oprofile:
Support for XLR/XLS processors] causes a compilation failure when
oprofile is enabled and SMP is not configured.
arch/mips/oprofile/op_model_mipsxx.c: In function 'mipsxx_cpu_setup':
arch/mips/oprofile/op_model_mipsxx.c:181:2: error: implicit declaration of function 'cpu_logical_map'
To fix this, update oprofile_skip_cpu to not call cpu_logical_map when
CONFIG_SMP is not defined.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/5037/
Acked-by: John Crispin <blogic@openwrt.org>
The definitions are not used anywhere else, and merging it will
make adding the new USB definitions for XLPII series easier.
While there, cleanup some whitespace in usb-init.c. There is no
change to logic due to this commit.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/5027/
Acked-by: John Crispin <blogic@openwrt.org>
This enables us to have a default device tree per SoC family to be built
into the kernel. The default device tree for XLP3xx has been added as part
of this change. Later this can be used to provide support default boards
for XLP2xx and XLP9xx SoCs.
Kconfig options are provided for each default device tree so that just the
needed ones can be selected to be built into the kernel.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/5023/
Acked-by: John Crispin <blogic@openwrt.org>
Remove unused functions and redundant comments from
arch/mips/include/asm/netlogic/haldefs.h
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/5029/
Acked-by: John Crispin <blogic@openwrt.org>
Update asm/netlogic/haldefs.h to extend register access functions
nlm_{read,write}_reg64() for 32-bit compilation. When compiled for 32-bit
the functions will read 64 IO registers with interrupts disabled.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/5026/
Acked-by: John Crispin <blogic@openwrt.org>
The index for a device interrupt in the PIC interrupt routing table
changes for different chips in the XLP family. Avoid using the fixed
entries and derive the index value from the SoC device header.
Add workarounds for some devices which do not report the IRT index
correctly.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/5025/
Acked-by: John Crispin <blogic@openwrt.org>
Use standard function to print cpumask. Also fixup the name of the
variable used and make it static.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/5024/
Acked-by: John Crispin <blogic@openwrt.org>
Remove the definitions of {read,write}_c0_{eirr,eimr}. These functions
are now unused after the PIC and IRQ code has been updated to use
optimized EIMR/EIRR functions which work on both 32-bit and 64-bit.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/5021/
Acked-by: John Crispin <blogic@openwrt.org>
Remove the irq save/restore from write_c0_eimr(), as it is always called
with interrupts off.
This allows us to remove workaround in write_c0_eimr() to fix up the
flags used by local_irq_save. This fixup worked on XLR, but will break
when 32-bit support is added to r2 cpus like XLP.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/5022/
Acked-by: John Crispin <blogic@openwrt.org>
All the header file does is provide the internal structure of clk,
which shouldn't be used by anyone except clk.c itself anyway.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patchwork: http://patchwork.linux-mips.org/patch/5055/
Acked-by: John Crispin <blogic@openwrt.org>
BCM6362 support booting from SPI flash and NAND.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5012/
Acked-by: John Crispin <blogic@openwrt.org>
The PCIe controller is almost the same as the BCM6328 one, with only
the SERDES register being at a different location.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5011/
Acked-by: John Crispin <blogic@openwrt.org>
The SPI controller shares the same register layout as the 6358 one.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5010/
Acked-by: John Crispin <blogic@openwrt.org>
Add basic support for detecting and booting the BCM6362.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5009/
Acked-by: John Crispin <blogic@openwrt.org>
Instead of trying to use a correlation of cpu prid and chip id and
hoping they will always be unique, use the cpu prid to determine the
chip id register location and just read out the chip id.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5008/
Acked-by: John Crispin <blogic@openwrt.org>
The REVID is only 8 bit wide.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5007/
Acked-by: John Crispin <blogic@openwrt.org>
BCM6338 and BCM6348, and BCM6358 and everything after that share the
same register layout. To not have to redefine them for each new chip
and keep the code size small, only use the definitions for the first
chip with the certain layout.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5006/
Acked-by: John Crispin <blogic@openwrt.org>
Pull more vfs updates from Al Viro:
"A couple of fixes + getting rid of __blkdev_put() return value"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
proc: Use PDE attribute setting accessor functions
make blkdev_put() return void
block_device_operations->release() should return void
mtd_blktrans_ops->release() should return void
hfs: SMP race on directory close()
Pull parisc updates from Helge Deller:
"Main fixes and updates in this patch series are:
- we faced kernel stack corruptions because of multiple delivery of
interrupts
- added kernel stack overflow checks
- added possibility to use dedicated stacks for irq processing
- initial support for page sizes > 4k
- more information in /proc/interrupts (e.g. TLB flushes and number
of IPI calls)
- documented how the parisc gateway page works
- and of course quite some other smaller cleanups and fixes."
* 'parisc-for-3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: tlb flush counting fix for SMP and UP
parisc: more irq statistics in /proc/interrupts
parisc: implement irq stacks
parisc: add kernel stack overflow check
parisc: only re-enable interrupts if we need to schedule or deliver signals when returning to userspace
parisc: implement atomic64_dec_if_positive()
parisc: use long branch in fork_like macro
parisc: fix NATIVE set up in build
parisc: document the parisc gateway page
parisc: fix partly 16/64k PAGE_SIZE boot
parisc: Provide default implementation for dma_{alloc, free}_attrs
parisc: fix whitespace errors in arch/parisc/kernel/traps.c
parisc: remove the second argument of kmap_atomic
Implements SMP support in Xen on ARM.
Add support for machine reboot and power off via Xen hypercalls.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=U5Oc
-----END PGP SIGNATURE-----
Merge tag '3.9-rc3-smp-6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/sstabellini/xen
Pull ARM Xen SMP updates from Stefano Stabellini:
"This contains a bunch of Xen/ARM specific changes, including some
fixes, SMP support for Xen on ARM, and moving the xenvm machine from
mach-vexpress to mach-virt.
The non-Xen files that are touched are arch/arm/Kconfig, to select
ARM_PSCI on XEN, and arch/arm/boot/dts/Makefile, to build the xenvm
DTB if CONFIG_ARCH_VIRT.
Highlights:
- Move xenvm to mach-virt.
- Implement SMP support in Xen on ARM.
- Add support for machine reboot and power off via Xen hypercalls"
* tag '3.9-rc3-smp-6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/sstabellini/xen:
xen/arm: remove duplicated include from enlighten.c
xen/arm: use sched_op hypercalls for machine reboot and power off
xenvm: add a simple PSCI node and a second cpu
xen/arm: XEN selects ARM_PSCI
xen: move the xenvm machine to mach-virt
xen/arm: SMP support
xen/arm: implement HYPERVISOR_vcpu_op
xen/arm: actually pass a non-NULL percpu pointer to request_percpu_irq
This patch adds a new udbg early debug console which utilises
statically defined input and output buffers stored within the kernel
BSS. It is primarily designed to assist with bring up of new hardware
which may not have a working console but which has a method of
reading/writing kernel memory.
This version incorporates comments made by Ben H (thanks!).
Changes from v1:
- Add memory barriers.
- Ensure updating of read/write positions is atomic.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Default kernel stack size on parisc is 16k. During tests we found that the
kernel stack can easily grow beyond 13k, which leaves 3k left for irq
processing.
This patch adds the possibility to activate an additional stack of 16k per CPU
which is being used during irq processing. This implementation does not yet
uses this irq stack for the irq bh handler.
The assembler code for call_on_stack was heavily cleaned up by John
David Anglin.
CC: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Add the CONFIG_DEBUG_STACKOVERFLOW config option to enable checks to
detect kernel stack overflows.
Stack overflows can not be detected reliable since we do not want to
introduce too much overhead.
Instead, during irq processing in do_cpu_irq_mask() we check kernel
stack usage of the interrupted kernel process. Kernel threads can be
easily detected by checking the value of space register 7 (sr7) which
is zero when running inside the kernel.
Since THREAD_SIZE is 16k and PAGE_SIZE is 4k, reduce the alignment of
the init thread to the lower value (PAGE_SIZE) in the kernel
vmlinux.ld.S linker script.
Signed-off-by: Helge Deller <deller@gmx.de>
arch/arm/mach-msm/last_radio_log.c: In function 'msm_init_last_radio_log':
arch/arm/mach-msm/last_radio_log.c:69:7: error: dereferencing pointer to incomplete type
arch/cris/kernel/profile.c: In function 'init_cris_profile':
arch/cris/kernel/profile.c:79:8: error: dereferencing pointer to incomplete type
Use proc_set_size(), cfr. commit 271a15eabe
("proc: Supply PDE attribute setting accessor functions")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Helge and I have found that we have a kernel stack overflow problem
which causes a variety of random failures.
Currently, we re-enable interrupts when returning from an external
interrupt incase we need to schedule or delivery
signals. As a result, a potentially unlimited number of interrupts
can occur while we are running on the kernel
stack. It is very limited in space (currently, 16k). This change
defers enabling interrupts until we have
actually decided to schedule or delivery signals. This only occurs
when we about to return to userspace. This
limits the number of interrupts on the kernel stack to one. In other
cases, interrupts remain disabled until the
final return from interrupt (rfi).
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
These continue the multiplatform support for exynos, adding support
for building most of the essential drivers (clocksource, clk, irqchip)
when combined with other platforms. As a result, it should become
really easy to add full multiplatform exynos support in 3.11, although
we don't yet enable it for 3.10.
The changes were not included in the earlier multiplatform series
in order to avoid clashes with the other Exynos updates.
This also includes work from Tomasz Figa to fix the pwm clocksource
code on Exynos, which is not strictly required for multiplatform,
but related to the other patches in this set and needed as a bug
fix for at least one board.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=FY7+
-----END PGP SIGNATURE-----
Merge tag 'multiplatform-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull late ARM Exynos multiplatform changes from Arnd Bergmann:
"These continue the multiplatform support for exynos, adding support
for building most of the essential drivers (clocksource, clk, irqchip)
when combined with other platforms. As a result, it should become
really easy to add full multiplatform exynos support in 3.11, although
we don't yet enable it for 3.10.
The changes were not included in the earlier multiplatform series in
order to avoid clashes with the other Exynos updates.
This also includes work from Tomasz Figa to fix the pwm clocksource
code on Exynos, which is not strictly required for multiplatform, but
related to the other patches in this set and needed as a bug fix for
at least one board."
* tag 'multiplatform-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (22 commits)
ARM: dts: exynops4210: really add universal_c210 dts
ARM: dts: exynos4210: Add basic dts file for universal_c210 board
ARM: dts: exynos4: Add node for PWM device
ARM: SAMSUNG: Do not register legacy timer interrupts on Exynos
clocksource: samsung_pwm_timer: Work around rounding errors in clockevents core
clocksource: samsung_pwm_timer: Correct programming of clock events
clocksource: samsung_pwm_timer: Use proper clockevents max_delta
clocksource: samsung_pwm_timer: Add support for non-DT platforms
clocksource: samsung_pwm_timer: Drop unused samsung_pwm struct
clocksource: samsung_pwm_timer: Keep all driver data in a structure
clocksource: samsung_pwm_timer: Make PWM spinlock global
clocksource: samsung_pwm_timer: Let platforms select the driver
Documentation: Add device tree bindings for Samsung PWM timers
clocksource: add samsung pwm timer driver
irqchip: exynos: look up irq using irq_find_mapping
irqchip: exynos: pass irq_base from platform
irqchip: exynos: localize irq lookup for ATAGS
irqchip: exynos: allocate combiner_data dynamically
irqchip: exynos: pass max combiner number to combiner_init
ARM: exynos: add missing properties for combiner IRQs
...
These are cleanups and smaller changes that either depend on earlier
feature branches or came in late during the development cycle.
We normally try to get all cleanups early, so these are the exceptions:
- A follow-up on the clocksource reworks, hopefully the last time
we need to merge clocksource subsystem changes through arm-soc.
A first set of patches was part of the original 3.10 arm-soc cleanup
series because of interdependencies with timer drivers now moved out
of arch/arm.
- Migrating the SPEAr13xx platform away from using auxdata for DMA
channel descriptions towards using information in device tree,
based on the earlier SPEAr multiplatform series
- A few follow-ups on the Atmel SAMA5 support and other changes
for Atmel at91 based on the larger at91 reworks.
- Moving the armada irqchip implementation to drivers/irqchip
- Several OMAP cleanups following up on the larger series already
merged in 3.10.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=HWfp
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late cleanups from Arnd Bergmann:
"These are cleanups and smaller changes that either depend on earlier
feature branches or came in late during the development cycle. We
normally try to get all cleanups early, so these are the exceptions:
- A follow-up on the clocksource reworks, hopefully the last time we
need to merge clocksource subsystem changes through arm-soc.
A first set of patches was part of the original 3.10 arm-soc
cleanup series because of interdependencies with timer drivers now
moved out of arch/arm.
- Migrating the SPEAr13xx platform away from using auxdata for DMA
channel descriptions towards using information in device tree,
based on the earlier SPEAr multiplatform series
- A few follow-ups on the Atmel SAMA5 support and other changes for
Atmel at91 based on the larger at91 reworks.
- Moving the armada irqchip implementation to drivers/irqchip
- Several OMAP cleanups following up on the larger series already
merged in 3.10."
* tag 'cleanup-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (50 commits)
ARM: OMAP4: change the device names in usb_bind_phy
ARM: OMAP2+: Fix mismerge for timer.c between ff931c82 and da4a686a
ARM: SPEAr: conditionalize SMP code
ARM: arch_timer: Silence debug preempt warnings
ARM: OMAP: remove unused variable
serial: amba-pl011: fix !CONFIG_DMA_ENGINE case
ata: arasan: remove the need for platform_data
ARM: at91/sama5d34ek.dts: remove not needed compatibility string
ARM: at91: dts: add MCI DMA support
ARM: at91: dts: add i2c dma support
ARM: at91: dts: set #dma-cells to the correct value
ARM: at91: suspend both memory controllers on at91sam9263
irqchip: armada-370-xp: slightly cleanup irq controller driver
irqchip: armada-370-xp: move IRQ handler to avoid forward declaration
irqchip: move IRQ driver for Armada 370/XP
ARM: mvebu: move L2 cache initialization in init_early()
devtree: add binding documentation for sp804
ARM: integrator-cp: convert use CLKSRC_OF for timer init
ARM: versatile: use OF init for sp804 timer
ARM: versatile: add versatile dtbs to dtbs target
...
These are mostly new device tree bindings for existing drivers, as well
as changes to the device tree source files to add support for those
devices, and a couple of new boards, most notably Samsung's Exynos5
based Chromebook.
The changes depend on earlier platform specific updates and touch
the usual platforms: omap, exynos, tegra, mxs, mvebu and davinci.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=G60S
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree updates (part 2) from Arnd Bergmann:
"These are mostly new device tree bindings for existing drivers, as
well as changes to the device tree source files to add support for
those devices, and a couple of new boards, most notably Samsung's
Exynos5 based Chromebook.
The changes depend on earlier platform specific updates and touch the
usual platforms: omap, exynos, tegra, mxs, mvebu and davinci."
* tag 'dt-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (169 commits)
ARM: exynos: dts: cros5250: add EC device
ARM: dts: Add sbs-battery for exynos5250-snow
ARM: dts: Add i2c-arbitrator bus for exynos5250-snow
ARM: dts: add mshc controller node for Exynos4x12 SoCs
ARM: dts: Add chip-id controller node on Exynos4/5 SoC
ARM: EXYNOS: Create virtual I/O mapping for Chip-ID controller using device tree
ARM: davinci: da850-evm: add SPI flash support
ARM: davinci: da850: override SPI DT node device name
ARM: davinci: da850: add SPI1 DT node
spi/davinci: add DT binding documentation
spi/davinci: no wildcards in DT compatible property
ARM: dts: mvebu: Convert mvebu device tree files to 64 bits
ARM: dts: mvebu: introduce internal-regs node
ARM: dts: mvebu: Convert all the mvebu files to use the range property
ARM: dts: mvebu: move all peripherals inside soc
ARM: dts: mvebu: fix cpus section indentation
ARM: davinci: da850: add EHRPWM & ECAP DT node
ARM/dts: OMAP3: fix pinctrl-single configuration
ARM: dts: Add OMAP3430 SDP NOR flash memory binding
ARM: dts: Add NOR flash bindings for OMAP2420 H4
...
This is the third and smallest of the SoC specific updates.
Changes include:
* SMP support for the Xilinx zynq platform
* Smaller imx changes
* LPAE support for mvebu
* Moving the orion5x, kirkwood, dove and mvebu platforms
to a common "mbus" driver for their internal devices.
It would be good to get feedback on the location of the "mbus"
driver. Since this is used on multiple platforms may potentially
get shared with other architectures (powerpc and arm64), it
was moved to drivers/bus/. We expect other similar drivers to
get moved to the same place in order to avoid creating more
top-level directories under drivers/ or cluttering up the
messy drivers/misc/ even more.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=rQsu
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus-3' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates (part 3) from Arnd Bergmann:
"This is the third and smallest of the SoC specific updates. Changes
include:
- SMP support for the Xilinx zynq platform
- Smaller imx changes
- LPAE support for mvebu
- Moving the orion5x, kirkwood, dove and mvebu platforms to a common
"mbus" driver for their internal devices.
It would be good to get feedback on the location of the "mbus" driver.
Since this is used on multiple platforms may potentially get shared
with other architectures (powerpc and arm64), it was moved to
drivers/bus/. We expect other similar drivers to get moved to the
same place in order to avoid creating more top-level directories under
drivers/ or cluttering up the messy drivers/misc/ even more."
* tag 'soc-for-linus-3' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (50 commits)
ARM: imx: reset_controller may be disabled
ARM: mvebu: Align the internal registers virtual base to support LPAE
ARM: mvebu: Limit the DMA zone when LPAE is selected
arm: plat-orion: remove addr-map code
arm: mach-mv78xx0: convert to use the mvebu-mbus driver
arm: mach-orion5x: convert to use mvebu-mbus driver
arm: mach-dove: convert to use mvebu-mbus driver
arm: mach-kirkwood: convert to use mvebu-mbus driver
arm: mach-mvebu: convert to use mvebu-mbus driver
ARM i.MX53: set CLK_SET_RATE_PARENT flag on the tve_ext_sel clock
ARM i.MX53: tve_di clock is not part of the CCM, but of TVE
ARM i.MX53: make tve_ext_sel propagate rate change to PLL
ARM i.MX53: Remove unused tve_gate clkdev entry
ARM i.MX5: Remove tve_sel clock from i.MX53 clock tree
ARM: i.MX5: Add PATA and SRTC clocks
ARM: imx: do not bring up unavailable cores
ARM: imx: add initial imx6dl support
ARM: imx1: mm: add call to mxc_device_init
ARM: imx_v4_v5_defconfig: Add CONFIG_GPIO_SYSFS
ARM: imx_v6_v7_defconfig: Select CONFIG_PERF_EVENTS
...
These patches are all for Renesas shmobile, and depend on the earlier
pinctrl updates. Remarkably, this adds support for three new SoCs:
r8a73a4, r8a73a4 and r8a7778. The bulk of the code added for these is
for pinctrl (using the new subsystem) and for clocks (not yet using the
common clock subsystem). The latter will have to get converted in one
of the upcoming releases, but shmobile is not ready for that yet.
The series also contains Renesas shmobile board changes, adding one
board file for each of the three new SoCs. These boards are using a
mix of classic and device-tree based probing, as there is still a lot of
infrastructure in shmobile that has not been converted to DT yet. Once
those are resolved to the degree that no board specific setup code is
needed, they can get folded into the respective SoC setup files.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=xaLf
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates (part 2) from Arnd Bergmann:
"These patches are all for Renesas shmobile, and depend on the earlier
pinctrl updates. Remarkably, this adds support for three new SoCs:
r8a73a4, r8a73a4 and r8a7778. The bulk of the code added for these is
for pinctrl (using the new subsystem) and for clocks (not yet using
the common clock subsystem). The latter will have to get converted in
one of the upcoming releases, but shmobile is not ready for that yet.
The series also contains Renesas shmobile board changes, adding one
board file for each of the three new SoCs. These boards are using a
mix of classic and device-tree based probing, as there is still a lot
of infrastructure in shmobile that has not been converted to DT yet.
Once those are resolved to the degree that no board specific setup
code is needed, they can get folded into the respective SoC setup files."
* tag 'soc-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (78 commits)
ARM: shmobile: use r8a7790 timer setup code on Lager
ARM: shmobile: force enable of r8a7790 arch timer
ARM: shmobile: Add second I/O range for r8a7790 PFC
ARM: shmobile: bockw: enable network settings on bootargs
ARM: shmobile: bockw: add SMSC ethernet support
ARM: shmobile: R8A7778: add Ether support
ARM: shmobile: bockw: enable SMSC ethernet on defconfig
ARM: shmobile: r8a7778: add r8a7778_init_irq_extpin()
ARM: shmobile: r8a7778: remove pointless PLATFORM_INFO()
ARM: shmobile: mackerel: clean up MMCIF vs. SDHI1 selection
ARM: shmobile: mackerel: add interrupt names for SDHI0
ARM: shmobile: mackerel: switch SDHI and MMCIF interfaces to slot-gpio
ARM: shmobile: mackerel: remove OCR masks, where regulators are used
ARM: shmobile: mackerel: SDHI resources do not have to be numbered
ARM: shmobile: Initial r8a7790 Lager board support
ARM: shmobile: APE6EVM LAN9220 support
ARM: shmobile: APE6EVM PFC support
ARM: shmobile: APE6EVM base support
ARM: shmobile: kzm9g-reference: add ethernet support
ARM: shmobile: add R-Car M1A Bock-W platform support
...
Pull powerpc updates from Benjamin Herrenschmidt:
"Here are a few more powerpc bits that I would like in 3.10.
Mostly remaining bolts & screw tightening of power8 support such as
actually exposing the new features via the previously added AT_HWCAP2,
and a few fixes, some of them for problems exposed recently like
irqdomain warnings or sysfs access permission issues, some exposed by
power8 hardware.
The only change outside of arch/powerpc is a small one to irqdomain.c
to allow silent failure to fix a problem on Cell where we get a dozen
WARN_ON's tripping at boot for what is basically a normal case."
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Make hard_irq_disable() do the right thing vs. irq tracing
powerpc/topology: Fix spurr attribute permission
powerpc/pci: Support per-aperture memory offset
powerpc/cell/iommu: Improve error message for missing node
powerpc/cell/spufs: Fix status attribute permission
irqdomain: Allow quiet failure mode
powerpc/pnv: Fix "compatible" property for P8 PHB
powerpc/pci: Don't add bogus empty resources to PHBs
powerpc/powerpnv: Properly handle failure starting CPUs
powerpc/cputable: Advertise support for ISEL/HTM/DSCR/TAR on POWER8
powerpc/cputable: Advertise ISEL support on appropriate embedded processors
powerpc/cputable: Advertise DSCR support on P7/P7+
powerpc/cputable: Reserve bits in HWCAP2 for new features
powerpc/pseries: Perform proper max_bus_speed detection
powerpc/pseries: Force 32 bit MSIs for devices that require it
powerpc/tm: Fix null pointer deference in flush_hash_page
powerpc/powernv: Defer OPAL exception handler registration
powerpc: Emulate non privileged DSCR read and write
Merge rwsem optimizations from Michel Lespinasse:
"These patches extend Alex Shi's work (which added write lock stealing
on the rwsem slow path) in order to provide rwsem write lock stealing
on the fast path (that is, without taking the rwsem's wait_lock).
I have unfortunately been unable to push this through -next before due
to Ingo Molnar / David Howells / Peter Zijlstra being busy with other
things. However, this has gotten some attention from Rik van Riel and
Davidlohr Bueso who both commented that they felt this was ready for
v3.10, and Ingo Molnar has said that he was OK with me pushing
directly to you. So, here goes :)
Davidlohr got the following test results from pgbench running on a
quad-core laptop:
| db_size | clients | tps-vanilla | tps-rwsem |
+---------+----------+----------------+--------------+
| 160 MB | 1 | 5803 | 6906 | + 19.0%
| 160 MB | 2 | 13092 | 15931 |
| 160 MB | 4 | 29412 | 33021 |
| 160 MB | 8 | 32448 | 34626 |
| 160 MB | 16 | 32758 | 33098 |
| 160 MB | 20 | 26940 | 31343 | + 16.3%
| 160 MB | 30 | 25147 | 28961 |
| 160 MB | 40 | 25484 | 26902 |
| 160 MB | 50 | 24528 | 25760 |
------------------------------------------------------
| 1.6 GB | 1 | 5733 | 7729 | + 34.8%
| 1.6 GB | 2 | 9411 | 19009 | + 101.9%
| 1.6 GB | 4 | 31818 | 33185 |
| 1.6 GB | 8 | 33700 | 34550 |
| 1.6 GB | 16 | 32751 | 33079 |
| 1.6 GB | 20 | 30919 | 31494 |
| 1.6 GB | 30 | 28540 | 28535 |
| 1.6 GB | 40 | 26380 | 27054 |
| 1.6 GB | 50 | 25241 | 25591 |
------------------------------------------------------
| 7.6 GB | 1 | 5779 | 6224 |
| 7.6 GB | 2 | 10897 | 13611 | + 24.9%
| 7.6 GB | 4 | 32683 | 33108 |
| 7.6 GB | 8 | 33968 | 34712 |
| 7.6 GB | 16 | 32287 | 32895 |
| 7.6 GB | 20 | 27770 | 31689 | + 14.1%
| 7.6 GB | 30 | 26739 | 29003 |
| 7.6 GB | 40 | 24901 | 26683 |
| 7.6 GB | 50 | 17115 | 25925 | + 51.5%
------------------------------------------------------
(Davidlohr also has one additional patch which further improves
throughput, though I will ask him to send it directly to you as I have
suggested some minor changes)."
* emailed patches from Michel Lespinasse <walken@google.com>:
rwsem: no need for explicit signed longs
x86 rwsem: avoid taking slow path when stealing write lock
rwsem: do not block readers at head of queue if other readers are active
rwsem: implement support for write lock stealing on the fastpath
rwsem: simplify __rwsem_do_wake
rwsem: skip initial trylock in rwsem_down_write_failed
rwsem: avoid taking wait_lock in rwsem_down_write_failed
rwsem: use cmpxchg for trying to steal write lock
rwsem: more agressive lock stealing in rwsem_down_write_failed
rwsem: simplify rwsem_down_write_failed
rwsem: simplify rwsem_down_read_failed
rwsem: move rwsem_down_failed_common code into rwsem_down_{read,write}_failed
rwsem: shorter spinlocked section in rwsem_down_failed_common()
rwsem: make the waiter type an enumeration rather than a bitmask
The core code expects the arch idle code to return with interrupts
enabled. The conversion missed two x86 cases which fail to do that.
Reported-and-tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Tested-by: Borislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/r/alpine.LFD.2.02.1305021557030.3972@ionos
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
modify __down_write[_nested] and __down_write_trylock to grab the write
lock whenever the active count is 0, even if there are queued waiters
(they must be writers pending wakeup, since the active count is 0).
Note that this is an optimization only; architectures without this
optimization will still work fine:
- __down_write() would take the slow path which would take the wait_lock
and then try stealing the lock (as in the spinlocked rwsem implementation)
- __down_write_trylock() would fail, but callers must be ready to deal
with that - since there are some writers pending wakeup, they could
have raced with us and obtained the lock before we steal it.
Signed-off-by: Michel Lespinasse <walken@google.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Davidlohr Bueso <davidlohr.bueso@hp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
They are important structures and it is not clear at first
look what they are for.
The xen_vcpu is a pointer. By default it points to the shared_info
structure (at the CPU offset location). However if the
VCPUOP_register_vcpu_info hypercall is implemented we can make the
xen_vcpu pointer point to a per-CPU location.
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
[v1: Added comments from Ian Campbell]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
flush_dcache_page( ) is MM hook to ensure that a page has consistent
views between kernel and userspace. Thus it is called when
* kernel writes to a page which at some later point could get mapped to
userspace (so kernel mapping needs to be flushed-n-inv)
* kernel is about to read from a page with possible userspace mappings
(so userspace mappings needs to be made coherent with kernel ones)
However for Non aliasing VIPT dcache, any userspace mapping will always
be congruent to kernel mapping. Thus d-cache need need not be flushed at
all (or delayed indefinitely).
The only reason it does need to be flushed is when mapping code pages.
Since icache doesn't snoop dcache, those dirty dcache lines need to be
written back to memory and icache line invalidated so that icache lines
fetch will get the right data.
Decent gains on LMBench fork/exec/sh and File I/O micro-benchmarks.
(1) FPGA @ 80 MHZ
Processor, Processes - times in microseconds - smaller is better
------------------------------------------------------------------------------
Host OS Mhz null null open slct sig sig fork exec sh
call I/O stat clos TCP inst hndl proc proc proc
--------- ------------- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ----
3.9-rc6-a Linux 3.9.0-r 80 4.79 8.72 66.7 116. 239. 8.39 30.4 4798 14.K 34.K
3.9-rc6-b Linux 3.9.0-r 80 4.79 8.62 65.4 111. 239. 8.35 29.0 3995 12.K 30.K
3.9-rc7-c Linux 3.9.0-r 80 4.79 9.00 66.1 106. 239. 8.61 30.4 2858 10.K 24.K
^^^^ ^^^^ ^^^
File & VM system latencies in microseconds - smaller is better
-------------------------------------------------------------------------------
Host OS 0K File 10K File Mmap Prot Page 100fd
Create Delete Create Delete Latency Fault Fault selct
--------- ------------- ------ ------ ------ ------ ------- ----- ------- -----
3.9-rc6-a Linux 3.9.0-r 317.8 204.2 1122.3 375.1 3522.0 4.288 20.7 126.8
3.9-rc6-b Linux 3.9.0-r 298.7 223.0 1141.6 367.8 3531.0 4.866 20.9 126.4
3.9-rc7-c Linux 3.9.0-r 278.4 179.2 862.1 339.3 3705.0 3.223 20.3 126.6
^^^^^ ^^^^^ ^^^^^ ^^^^
(2) Customer Silicon @ 500 MHz (166 MHz mem)
------------------------------------------------------------------------------
Host OS Mhz null null open slct sig sig fork exec sh
call I/O stat clos TCP inst hndl proc proc proc
--------- ------------- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ----
abilis-ba Linux 3.9.0-r 497 0.71 1.38 4.58 12.0 35.5 1.40 3.89 2070 5525 13.K
abilis-ca Linux 3.9.0-r 497 0.71 1.40 4.61 11.8 35.6 1.37 3.92 1411 4317 10.K
^^^^ ^^^^ ^^^
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
start address is already page aligned and size is const PAGE_SIZE,
thus fixups for alignment not needed in generated code.
bloat-o-meter vmlinux-mm5 vmlinux
add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-32 (-32)
function old new delta
__inv_icache_page 82 50 -32
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Now that we have same helper used for all icache invalidates (i.e.
vaddr+paddr based exact line invalidate), consolidate the open coded
calls into one place.
Also rename flush_icache_range_vaddr => __sync_icache_dcache
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This change continues the theme from prev commit - this time icache
handling for kernel's own code modification (vmalloc: loadable modules,
breakpoints for kprobes/kgdb...)
flush_icache_range() calls the CDU icache helper with vaddr to enable
exact line invalidate.
For a true kernel-virtual mapping, the vaddr is actually virtual hence
valid as index into cache. For kprobes breakpoint however, the vaddr arg
is actually paddr - since that's how normal kernel is mapped in ARC
memory map. This implies that CDU will use the same addr for
indexing as for tag match - which is fine since kernel code would only
have that "implicit" mapping and none other.
This should speed up module loading significantly - specially on default
ARC700 icache configurations (32k) which alias.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
ARC icache doesn't snoop dcache thus executable pages need to be made
coherent before mapping into userspace in flush_icache_page().
However ARC700 CDU (hardware cache flush module) requires both vaddr
(index in cache) as well as paddr (tag match) to correctly identify a
line in the VIPT cache. A typical ARC700 SoC has aliasing icache, thus
the paddr only based flush_icache_page() API couldn't be implemented
efficiently. It had to loop thru all possible alias indexes and perform
the invalidate operation (ofcourse the cache op would only succeed at
the index(es) where tag matches - typically only 1, but the cost of
visiting all the cache-bins needs to paid nevertheless).
Turns out however that the vaddr (along with paddr) is available in
update_mmu_cache() hence better suits ARC icache flush semantics.
With both vaddr+paddr, exactly one flush operation per line is done.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
musb device naming change.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=FjKm
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.10/fixes-for-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into late/cleanup
From Tony Lindgren <tony@atomide.com>:
An urgent fix for a timer mismerge for and a regression fix for
musb device naming change.
* tag 'omap-for-v3.10/fixes-for-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP4: change the device names in usb_bind_phy
ARM: OMAP2+: Fix mismerge for timer.c between ff931c82 and da4a686a
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch is from Frank.Shew,fshew@geometrics.com to fix the
following problem:having extremely slow responses with the NAND
due to timeouts on the ready status signal, which eventually
caused the watchdog to time out.
Signed-off-by: Aaron Wu <Aaron.Wu@analog.com>
Signed-off-by: Steven Miao <realmz6@gmail.com>
rename vmImage to uImage
update blackfin targets name
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Steven Miao <realmz6@gmail.com>
arch/blackfin/mach-bf538/boards/ezkit.c:768:2: error: #endif without #if
Introduced by commit cf93feb3a0 ("blackfin:
twi: Move TWI peripheral pin request array to platform data"), which
removed the #if, but forgot about the #endif.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Steven Miao <realmz6@gmail.com>
Clean up some trailing whitespace issues in arch/arm/Makefile.
Signed-off-by: Daniel Tang <dt.tangr@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The CPU used in Marvell Dove SoCs is a PJ4 Sheeva core. Using
CONFIG_CPU_PJ4 instead of CONFIG_CPU_V7 will enable iWMMXt
extensions on Dove.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
munmap ends up calling tlb_flush() which for ARC was flushing the entire
TLB unconditionally (by moving the MMU to a new ASID)
do_munmap
unmap_region
unmap_vmas
unmap_single_vma
unmap_page_range
tlb_start_vma
zap_pud_range
tlb_end_vma()
tlb_finish_mmu
tlb_flush() ---> unconditional flush_tlb_mm()
So even a single page munmap, a frequent operation when uClibc dynamic
linker (ldso) is loading the dependent shared libraries, would move the
the ASID multiple times - needlessly invalidating the pre-faulted TLB
entries (and increasing the rate of ASID wraparound + full TLB flush).
This is now optimised to only be called if tlb->full_mm (which means
for exit/execve) cases only. And for those cases, flush_tlb_mm() is
already optimised to be a no-op for mm->mm_users == 0.
So essentially there are no mmore full mm flushes - except for fork which
anyhow needs it for properly COW'ing parent address space.
munmap now needs to do TLB range flush, which is implemented with
tlb_end_vma()
Results
-------
1. ASID now consistenly moves by 4 during a simple ls (as opposed to 5 or
7 before).
2. LMBench microbenchmark also shows improvements
Basic system parameters
------------------------------------------------------------------------------
Host OS Description Mhz tlb cache mem scal
pages line par load
bytes
--------- ------------- ----------------------- ---- ----- ----- ------ ----
3.9-rc5-0 Linux 3.9.0-r 3.9-rc5-0404-gcc-4.4-ba 80 8 64 1.1000 1
3.9-rc5-0 Linux 3.9.0-r 3.9-rc5-0405-avoid-full 80 8 64 1.1200 1
Processor, Processes - times in microseconds - smaller is better
------------------------------------------------------------------------------
Host OS Mhz null null open slct sig sig fork exec sh
call I/O stat clos TCP inst hndl proc proc proc
--------- ------------- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ----
3.9-rc5-0 Linux 3.9.0-r 80 4.81 8.69 68.6 118. 239. 8.53 31.6 4839 13.K 34.K
3.9-rc5-0 Linux 3.9.0-r 80 4.46 8.36 53.8 91.3 223. 8.12 24.2 4725 13.K 33.K
File & VM system latencies in microseconds - smaller is better
-------------------------------------------------------------------------------
Host OS 0K File 10K File Mmap Prot Page 100fd
Create Delete Create Delete Latency Fault Fault selct
--------- ------------- ------ ------ ------ ------ ------- ----- ------- -----
3.9-rc5-0 Linux 3.9.0-r 314.7 223.2 1054.9 390.2 3615.0 1.590 20.1 126.6
3.9-rc5-0 Linux 3.9.0-r 265.8 183.8 1014.2 314.1 3193.0 6.910 18.8 110.4
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This adds support for an ARC Virtual Platform. This platform is based on the
System C standard promoted by the OSCI (Open System C Initiative) and uses
nSIM to simulate the ARC CPU core itself.
Users can build a virtual SoC by combining System C models of peripherals
and CPU cores.
Signed-off-by: Mischa Jonker <mjonker@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The original device tree was written using a slightly different
implementation of the fixed-factor-clock device tree binding. The
compatible string must be modified in order to be compatible with the
new implementation.
Signed-off-by: Christian Ruppert <christian.ruppert@abilis.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Infrastructure required to make the Linux kernel compile and boot on the
Abilis Systems TB10x series of SOCs based on ARC700 CPUs:
- Kmake related files (Kconfig, Makefile, tb10x_defconfig)
- TB10x platform initialisation
Signed-off-by: Christian Ruppert <christian.ruppert@abilis.com>
Signed-off-by: Pierrick Hascoet <pierrick.hascoet@abilis.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
These are the device tree files for the Abilis Systems TB100 and TB101 ICs and
their respective development kit PCBs. These files are committed in preparation
of the following patch set which adds support for these chips to the ARC
platform.
Signed-off-by: Christian Ruppert <christian.ruppert@abilis.com>
Signed-off-by: Pierrick Hascoet <pierrick.hascoet@abilis.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This patch adds some room for CPU-external interrupt controllers in the
Linux interrupt space. Until now, only the 32 CPU internal interrupt lines
were supported which does not allow for external interrupt controllers such
as GPIO modules etc.
Signed-off-by: Christian Ruppert <christian.ruppert@abilis.com>
Signed-off-by: Pierrick Hascoet <pierrick.hascoet@abilis.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
arc-intc is initialized in arc common code as it is applicable to all
platforms. However platforms with their own external intc still need to
refer to it for correct DT interrupt tree hierarchy setup,
e.g.
static struct of_device_id __initdata tb10x_irq_ids[] = {
{ .compatible = "snps,arc700-intc", .data = dummy_init_irq },
{ .compatible = "abilis,tb10x_ictl", .data = tb10x_init_irq },
{},
};
The fix is to use the generic irqchip framework to tie all irqchips in
a special linker section and then call irqchip_init() which calls the
DT of_irq_init() for all the intc in one go.
That way the platform code need not be aware of arc-intc at all.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The existing code was wrong on several counts:
* uboot provided bootargs were copied into @boot_command_line, only to
be over-written by setup_machine_fdt(), effectively lost
* @cmdline_p returned by setup_arch() to start_kernel() didn't include
the DT /bootargs
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Given that DeviceTree /bootargs can provide similar functionality,
no point in providing duplicate infrastructure.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The fixup code correctly updates the callee-regs on stack, but
fails to unwind it into actual register file. Thus userspace won't see
the update.
Reported-by: Noam Camus <noamc@ezchip.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
If CONFIG_ARC_MISALIGN_ACCESS is not enabled, or if the fixup fails,
call the same error handler: same signal/si_code to user (SIGBUS)
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
* Remove the line-break between scratch/callee-regs (sneaked in when we
converted from printk to pr_*
* Use %pS to print the symbol names of faulting PC (ret pseudo register)
and BLINK (call return register)
* Don't print user-vma for a kernel crash (only do it for
print-fatal-signals based regfile dump)
* Verbose print the Interrupt/Exception Enable/Active state
* for main executable link address is 0x10000 based (vs. 0) thus offset
of faulting PC needs to be adjusted
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This tracks mainline commit ae903caae2 "Bury the conditionals from
kernel_thread/kernel_execve series" which we missed out as ARC port was
not yet mainline.
[vgupta: commit log modified]
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
If hard_irq_disable() is called while interrupts are already soft-disabled
(which is the most common case) all is already well.
However you can (and in some cases want) to call it while everything is
enabled (to make sure you don't get a lazy even, for example before entry
into KVM guests) and in this case we need to inform the irq tracer that
the irqs are going off.
We have to change the inline into a macro to avoid an include circular
dependency hell hole.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The value passed is 0 in all but "it can never happen" cases (and those
only in a couple of drivers) *and* it would've been lost on the way
out anyway, even if something tried to pass something meaningful.
Just don't bother.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
After the device names are created using PLATFORM_DEVID_AUTO, the old
device names given in usb_bind_phy are no longer valid causing the musb
controller not to get the phy reference. Updated the usb_bind_phy with
the new device names to get MUSB functional in omap4 panda.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like the timer.c fixes in commit ff931c82 (ARM: OMAP: clocks:
Delay clk inits atleast until slab is initialized) got lost in a
merge with da4a686a (ARM: smp_twd: convert to use CLKSRC_OF init).
Without the omap_clk_init() calls none of OMAP family of devices
boot.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
[tony@atomide.com: updated comments to describe merge error]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The updates are mostly about the x86 IOMMUs this time. Exceptions are
the groundwork for the PAMU IOMMU from Freescale (for a PPC platform)
and an extension to the IOMMU group interface. On the x86 side this
includes a workaround for VT-d to disable interrupt remapping on broken
chipsets. On the AMD-Vi side the most important new feature is a kernel
command-line interface to override broken information in IVRS ACPI
tables and get interrupt remapping working this way. Besides that there
are small fixes all over the place.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=MVc/
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
"The updates are mostly about the x86 IOMMUs this time.
Exceptions are the groundwork for the PAMU IOMMU from Freescale (for a
PPC platform) and an extension to the IOMMU group interface.
On the x86 side this includes a workaround for VT-d to disable
interrupt remapping on broken chipsets. On the AMD-Vi side the most
important new feature is a kernel command-line interface to override
broken information in IVRS ACPI tables and get interrupt remapping
working this way.
Besides that there are small fixes all over the place."
* tag 'iommu-updates-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (24 commits)
iommu/tegra: Fix printk formats for dma_addr_t
iommu: Add a function to find an iommu group by id
iommu/vt-d: Remove warning for HPET scope type
iommu: Move swap_pci_ref function to drivers/iommu/pci.h.
iommu/vt-d: Disable translation if already enabled
iommu/amd: fix error return code in early_amd_iommu_init()
iommu/AMD: Per-thread IOMMU Interrupt Handling
iommu: Include linux/err.h
iommu/amd: Workaround for ERBT1312
iommu/amd: Document ivrs_ioapic and ivrs_hpet parameters
iommu/amd: Don't report firmware bugs with cmd-line ivrs overrides
iommu/amd: Add ioapic and hpet ivrs override
iommu/amd: Add early maps for ioapic and hpet
iommu/amd: Extend IVRS special device data structure
iommu/amd: Move add_special_device() to __init
iommu: Fix compile warnings with forward declarations
iommu/amd: Properly initialize irq-table lock
iommu/amd: Use AMD specific data structure for irq remapping
iommu/amd: Remove map_sg_no_iommu()
iommu/vt-d: add quirk for broken interrupt remapping on 55XX chipsets
...
This series from Tomasz Figa restores support for the pwm clocksource
in Exynos, which was broken during the conversion of the platform
to the common clk framework. The clocksource is only used in one
board in the mainline kernel (universal_c210), and this makes it
work for DT based probing as well as restoring the non-DT based
case.
* exynos/pwm-clocksource:
ARM: dts: exynops4210: really add universal_c210 dts
ARM: dts: exynos4210: Add basic dts file for universal_c210 board
ARM: dts: exynos4: Add node for PWM device
ARM: SAMSUNG: Do not register legacy timer interrupts on Exynos
clocksource: samsung_pwm_timer: Work around rounding errors in clockevents core
clocksource: samsung_pwm_timer: Correct programming of clock events
clocksource: samsung_pwm_timer: Use proper clockevents max_delta
clocksource: samsung_pwm_timer: Add support for non-DT platforms
clocksource: samsung_pwm_timer: Drop unused samsung_pwm struct
clocksource: samsung_pwm_timer: Keep all driver data in a structure
clocksource: samsung_pwm_timer: Make PWM spinlock global
clocksource: samsung_pwm_timer: Let platforms select the driver
Documentation: Add device tree bindings for Samsung PWM timers
clocksource: add samsung pwm timer driver
Conflicts:
arch/arm/boot/dts/Makefile
arch/arm/mach-exynos/common.c
drivers/clocksource/Kconfig
drivers/clocksource/Makefile
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
There is no reason to keep the clksrc cleanups separate from the
other cleanups, and this resolves some merge conflicts.
Conflicts:
arch/arm/mach-spear/spear13xx.c
drivers/irqchip/Makefile
This is support for the ARM Chromebook, originally scheduled
as a "late" pull request. Since it's already late now, we
can combine this into the existing next/dt2 branch.
* late/dt:
ARM: exynos: dts: cros5250: add EC device
ARM: dts: Add sbs-battery for exynos5250-snow
ARM: dts: Add i2c-arbitrator bus for exynos5250-snow
ARM: dts: Add chip-id controller node on Exynos4/5 SoC
ARM: EXYNOS: Create virtual I/O mapping for Chip-ID controller using device tree
The "b" branch instruction used in the fork_like macro only can handle
17-bit pc-relative offsets.
This fails with an out of range offset with some .config files.
Rewrite to use the "be" instruction which
can branch to any address in a space.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
The ifeq operator does not accept globs, so this little bit of code will
never match (unless uname literally prints out "parsic*"). Rewrite to
use a pattern matching operator so that NATIVE is set to 1 on parisc.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Helge Deller <deller@gmx.de>
Include some documentation about how the parisc gateway page technically
works and how it is used from userspace.
James Bottomley is the original author of this description and it was
copied here out of an email thread from Apr 12 2013 titled:
man2 : syscall.2 : document syscall calling conventions
CC: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Helge Deller <deller@gmx.de>
This patch fixes partly PAGE_SIZEs of 16K or 64K by adjusting the
assembler PTE lookup code and the assembler TEMPALIAS code. Furthermore
some data alignments for PAGE_SIZE have been limited to 4K (or less) to
not waste too much memory with greater page sizes. As a side note, the
palo loader can (currently) only handle up to 10 ELF segments which is
fixed with tighter aligning as well.
My testings indicated that the ldci command in the sba iommu coding
needed adjustment by the PAGE_SHIFT value and that the I/O PDIR Page
size was only set to 4K for my machine (C3000).
All this fixes partly the boot, but there are still quite some caching
problems left. Examples are e.g. the symbios logic driver which is
failing:
sym0: <896> rev 0x7 at pci 0000:00:0f.0 irq 69
sym0: PA-RISC Firmware, ID 7, Fast-40, SE, parity checking
CACHE TEST FAILED: DMA error (dstat=0x81).sym0: CACHE INCORRECTLY CONFIGURED.
and the tulip network driver which doesn't seem to work correctly
either:
Sending BOOTP requests .net eth0: Setting full-duplex based on MII#1
link partner capability of 05e1
..... timed out!
Beside those kernel fixes glibc will need fixes too to be able to handle
>4K page sizes.
Signed-off-by: Helge Deller <deller@gmx.de>
Most architectures that define CONFIG_HAVE_DMA, have implementations for
both dma_alloc_attrs() and dma_free_attrs(). All achitectures that do
not define CONFIG_HAVE_DMA also have both of these definitions provided by
dma-mapping-broken.h.
Add default implementations for these functions on parisc.
Signed-off-by: Damian Hobson-Garcia <dhobsong@igel.co.jp>
Signed-off-by: Helge Deller <deller@gmx.de>
Things like " \t" and whitespace at end of line. I'm leaving all the other
coding style errors here alone.
Signed-off-by: Rolf Eike Beer <eike-kernel@sf-tec.de>
Signed-off-by: Helge Deller <deller@gmx.de>
kmap_atomic allows only one argument now, just move the second.
Signed-off-by: Zhao Hongjiang <zhaohongjiang@huawei.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Pull more s390 updates from Martin Schwidefsky:
"This is the second batch of s390 patches for the 3.10 merge window.
Heiko improved the memory detection, this fixes kdump for large memory
sizes. Some kvm related memory management work, new ipldev/condev
keywords in cio and bug fixes."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/mem_detect: remove artificial kdump memory types
s390/mm: add pte invalidation notifier for kvm
s390/zcrypt: ap bus rescan problem when toggle crypto adapters on/off
s390/memory hotplug,sclp: get rid of per memory increment usecount
s390/memory hotplug: provide memory_block_size_bytes() function
s390/mem_detect: limit memory detection loop to "mem=" parameter
s390/kdump,bootmem: fix bootmem allocator bitmap size
s390: get rid of odd global real_memory_size
s390/kvm: Change the virtual memory mapping location for Virtio devices
s390/zcore: calculate real memory size using own get_mem_size function
s390/mem_detect: add DAT sanity check
s390/mem_detect: fix lockdep irq tracing
s390/mem_detect: move memory detection code to mm folder
s390/zfcpdump: exploit new cio_ignore keywords
s390/cio: add condev keyword to cio_ignore
s390/cio: add ipldev keyword to cio_ignore
s390/uaccess: add "fallthrough" comments
If a user did:
echo 0 > /sys/devices/system/cpu/cpu1/online
echo 1 > /sys/devices/system/cpu/cpu1/online
we would (this a build with DEBUG enabled) get to:
smpboot: ++++++++++++++++++++=_---CPU UP 1
.. snip..
smpboot: Stack at about ffff880074c0ff44
smpboot: CPU1: has booted.
and hang. The RCU mechanism would kick in an try to IPI the CPU1
but the IPIs (and all other interrupts) would never arrive at the
CPU1. At first glance at least. A bit digging in the hypervisor
trace shows that (using xenanalyze):
[vla] d4v1 vec 243 injecting
0.043163027 --|x d4v1 intr_window vec 243 src 5(vector) intr f3
] 0.043163639 --|x d4v1 vmentry cycles 1468
] 0.043164913 --|x d4v1 vmexit exit_reason PENDING_INTERRUPT eip ffffffff81673254
0.043164913 --|x d4v1 inj_virq vec 243 real
[vla] d4v1 vec 243 injecting
0.043164913 --|x d4v1 intr_window vec 243 src 5(vector) intr f3
] 0.043165526 --|x d4v1 vmentry cycles 1472
] 0.043166800 --|x d4v1 vmexit exit_reason PENDING_INTERRUPT eip ffffffff81673254
0.043166800 --|x d4v1 inj_virq vec 243 real
[vla] d4v1 vec 243 injecting
there is a pending event (subsequent debugging shows it is the IPI
from the VCPU0 when smpboot.c on VCPU1 has done
"set_cpu_online(smp_processor_id(), true)") and the guest VCPU1 is
interrupted with the callback IPI (0xf3 aka 243) which ends up calling
__xen_evtchn_do_upcall.
The __xen_evtchn_do_upcall seems to do *something* but not acknowledge
the pending events. And the moment the guest does a 'cli' (that is the
ffffffff81673254 in the log above) the hypervisor is invoked again to
inject the IPI (0xf3) to tell the guest it has pending interrupts.
This repeats itself forever.
The culprit was the per_cpu(xen_vcpu, cpu) pointer. At the bootup
we set each per_cpu(xen_vcpu, cpu) to point to the
shared_info->vcpu_info[vcpu] but later on use the VCPUOP_register_vcpu_info
to register per-CPU structures (xen_vcpu_setup).
This is used to allow events for more than 32 VCPUs and for performance
optimizations reasons.
When the user performs the VCPU hotplug we end up calling the
the xen_vcpu_setup once more. We make the hypercall which returns
-EINVAL as it does not allow multiple registration calls (and
already has re-assigned where the events are being set). We pick
the fallback case and set per_cpu(xen_vcpu, cpu) to point to the
shared_info->vcpu_info[vcpu] (which is a good fallback during bootup).
However the hypervisor is still setting events in the register
per-cpu structure (per_cpu(xen_vcpu_info, cpu)).
As such when the events are set by the hypervisor (such as timer one),
and when we iterate in __xen_evtchn_do_upcall we end up reading stale
events from the shared_info->vcpu_info[vcpu] instead of the
per_cpu(xen_vcpu_info, cpu) structures. Hence we never acknowledge the
events that the hypervisor has set and the hypervisor keeps on reminding
us to ack the events which we never do.
The fix is simple. Don't on the second time when xen_vcpu_setup is
called over-write the per_cpu(xen_vcpu, cpu) if it points to
per_cpu(xen_vcpu_info).
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
CC: stable@vger.kernel.org
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
We are registering the attribute with permission 0600 but it
doesn't have a store callback, which causes WARN_ON's during
boot. Fix the permission.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The PCI core supports an offset per aperture nowadays but our arch
code still has a single offset per host bridge representing the
difference betwen CPU memory addresses and PCI MMIO addresses.
This is a problem as new machines and hypervisor versions are
coming out where the 64-bit windows will have a different offset
(basically mapped 1:1) from the 32-bit windows.
This fixes it by using separate offsets. In the long run, we probably
want to get rid of that intermediary struct pci_controller and have
those directly stored into the pci_host_bridge as they are parsed
but this will be a more invasive change.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Some devices don't have a correct node ID and thus can't be
attached to an iommu.
The message displayed by the iommu code isn't very useful if
you don't have a device-tree node as it tries to print the
device-tree path but not the struct device name.
Improve this by printing the device name as well.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We are registering the attribute with permission 0644 but it
doesn't have a store callback, which causes WARN_ON's during
boot. Fix the permission.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Some interrupt controllers refuse to map interrupts marked as
"protected" by firwmare. Since we try to map everyting in the
device-tree on some platforms, we end up with a lot of nasty
WARN's in the boot log for what is a normal situation on those
machines.
This defines a specific return code (-EPERM) from the host map()
callback which cause irqdomain to fail silently.
MPIC is updated to return this when hitting a protected source
printing only a single line message for diagnostic purposes.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
- The ChromeOS embedded controller which provides keyboard, battery and power
management services. This controller is accessible through i2c or SPI.
- Silicon Laboratories 476x controller, providing access to their FM chipset
and their audio codec.
- Realtek's RTS5249, a memory stick, MMC and SD/SDIO PCI based reader.
- Nokia's Tahvo power button and watchdog device. This device is very similar
to Retu and is thus supported by the same code base.
- STMicroelectronics STMPE1801, a keyboard and GPIO controller supported by
the stmpe driver.
- ST-Ericsson AB8540 and AB8505 power management and voltage converter
controllers through the existing ab8500 code.
Some other drivers got cleaned up or improved. In particular:
- The Linaro/STE guys got the ab8500 driver in sync with their internal code
through a series of optimizations, fixes and improvements.
- The AS3711 and OMAP USB drivers now have DT support.
- The arizona clock and interrupt handling code got improved.
- The wm5102 register patch and boot mechanism also got improved.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=Wq20
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-next
Pull MFD update from Samuel Ortiz:
"For 3.10 we have a few new MFD drivers for:
- The ChromeOS embedded controller which provides keyboard, battery
and power management services. This controller is accessible
through i2c or SPI.
- Silicon Laboratories 476x controller, providing access to their FM
chipset and their audio codec.
- Realtek's RTS5249, a memory stick, MMC and SD/SDIO PCI based
reader.
- Nokia's Tahvo power button and watchdog device. This device is
very similar to Retu and is thus supported by the same code base.
- STMicroelectronics STMPE1801, a keyboard and GPIO controller
supported by the stmpe driver.
- ST-Ericsson AB8540 and AB8505 power management and voltage
converter controllers through the existing ab8500 code.
Some other drivers got cleaned up or improved. In particular:
- The Linaro/STE guys got the ab8500 driver in sync with their
internal code through a series of optimizations, fixes and
improvements.
- The AS3711 and OMAP USB drivers now have DT support.
- The arizona clock and interrupt handling code got improved.
- The wm5102 register patch and boot mechanism also got improved."
* tag 'mfd-3.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-next: (104 commits)
mfd: si476x: Don't use 0bNNN
mfd: vexpress: Handle pending config transactions
mfd: ab8500: Export ab8500_gpadc_sw_hw_convert properly
mfd: si476x: Fix i2c warning
mfd: si476x: Add header files and Kbuild plumbing
mfd: si476x: Add chip properties handling code
mfd: si476x: Add the bulk of the core driver
mfd: si476x: Add commands abstraction layer
mfd: rtsx: Support RTS5249
mfd: retu: Add Tahvo support
mfd: ucb1400: Pass ucb1400-gpio data through ac97 bus
mfd: wm8994: Add some OF properties
mfd: wm8994: Add device ID data to WM8994 OF device IDs
input: Export matrix_keypad_parse_of_params()
mfd: tps65090: Add compatible string for charger subnode
mfd: db8500-prcmu: Support platform dependant device selection
mfd: syscon: Fix warnings when printing resource_size_t
of: Add stub of_get_parent for non-OF builds
mfd: omap-usb-tll: Convert to devm_ioremap_resource()
mfd: omap-usb-host: Convert to devm_ioremap_resource()
...
The property should be "ibm,power8-pciex", not "ibm,p8-pciex". The latter
was changed in FW because it was inconsistent with the rest of the nodes.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When converting to use the new pci_add_resource_offset() we didn't
properly account for empty resources (0 flags) and add those bogons
to the PHBs. The result is some annoying messages in the log.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If OPAL returns an error, propagate it upward rather than spinning
seconds waiting for a CPU that will never show up
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Also, make HTM's presence dependent on the .config option.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On pseries machines the detection for max_bus_speed should be done
through an OpenFirmware property. This patch adds a function to perform
this detection and a hook to perform dynamic adding of the function only
for pseries. This is done by overwriting the weak
pcibios_root_bridge_prepare function which is called by
pci_create_root_bus().
From: Lucas Kannebley Tavares <lucaskt@linux.vnet.ibm.com>
Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The following patch implements a new PAPR change which allows
the OS to force the use of 32 bit MSIs, regardless of what
the PCI capabilities indicate. This is required for some
devices that advertise support for 64 bit MSIs but don't
actually support them.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Make sure that current->thread.reg exists before we deference it in
flush_hash_page.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Reported-by: John J Miller <millerjo@us.ibm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently, the OPAL exception vectors are registered before the feature
fixups are processed. This means that the now-firmware-owned vectors
will likely be overwritten by the kernel.
This change moves the exception registration code to an early initcall,
rather than at machine_init time.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
POWER8 allows read and write of the DSCR in userspace. We added
kernel emulation so applications could always use the instructions
regardless of the CPU type.
Unfortunately there are two SPRs for the DSCR and we only added
emulation for the privileged one. Add code to match the non
privileged one.
A simple test was created to verify the fix:
http://ozlabs.org/~anton/junkcode/user_dscr_test.c
Without the patch we get a SIGILL and it passes with the patch.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Pull kvm updates from Gleb Natapov:
"Highlights of the updates are:
general:
- new emulated device API
- legacy device assignment is now optional
- irqfd interface is more generic and can be shared between arches
x86:
- VMCS shadow support and other nested VMX improvements
- APIC virtualization and Posted Interrupt hardware support
- Optimize mmio spte zapping
ppc:
- BookE: in-kernel MPIC emulation with irqfd support
- Book3S: in-kernel XICS emulation (incomplete)
- Book3S: HV: migration fixes
- BookE: more debug support preparation
- BookE: e6500 support
ARM:
- reworking of Hyp idmaps
s390:
- ioeventfd for virtio-ccw
And many other bug fixes, cleanups and improvements"
* tag 'kvm-3.10-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (204 commits)
kvm: Add compat_ioctl for device control API
KVM: x86: Account for failing enable_irq_window for NMI window request
KVM: PPC: Book3S: Add API for in-kernel XICS emulation
kvm/ppc/mpic: fix missing unlock in set_base_addr()
kvm/ppc: Hold srcu lock when calling kvm_io_bus_read/write
kvm/ppc/mpic: remove users
kvm/ppc/mpic: fix mmio region lists when multiple guests used
kvm/ppc/mpic: remove default routes from documentation
kvm: KVM_CAP_IOMMU only available with device assignment
ARM: KVM: iterate over all CPUs for CPU compatibility check
KVM: ARM: Fix spelling in error message
ARM: KVM: define KVM_ARM_MAX_VCPUS unconditionally
KVM: ARM: Fix API documentation for ONE_REG encoding
ARM: KVM: promote vfp_host pointer to generic host cpu context
ARM: KVM: add architecture specific hook for capabilities
ARM: KVM: perform HYP initilization for hotplugged CPUs
ARM: KVM: switch to a dual-step HYP init code
ARM: KVM: rework HYP page table freeing
ARM: KVM: enforce maximum size for identity mapped code
ARM: KVM: move to a KVM provided HYP idmap
...
Pull 'full dynticks' support from Ingo Molnar:
"This tree from Frederic Weisbecker adds a new, (exciting! :-) core
kernel feature to the timer and scheduler subsystems: 'full dynticks',
or CONFIG_NO_HZ_FULL=y.
This feature extends the nohz variable-size timer tick feature from
idle to busy CPUs (running at most one task) as well, potentially
reducing the number of timer interrupts significantly.
This feature got motivated by real-time folks and the -rt tree, but
the general utility and motivation of full-dynticks runs wider than
that:
- HPC workloads get faster: CPUs running a single task should be able
to utilize a maximum amount of CPU power. A periodic timer tick at
HZ=1000 can cause a constant overhead of up to 1.0%. This feature
removes that overhead - and speeds up the system by 0.5%-1.0% on
typical distro configs even on modern systems.
- Real-time workload latency reduction: CPUs running critical tasks
should experience as little jitter as possible. The last remaining
source of kernel-related jitter was the periodic timer tick.
- A single task executing on a CPU is a pretty common situation,
especially with an increasing number of cores/CPUs, so this feature
helps desktop and mobile workloads as well.
The cost of the feature is mainly related to increased timer
reprogramming overhead when a CPU switches its tick period, and thus
slightly longer to-idle and from-idle latency.
Configuration-wise a third mode of operation is added to the existing
two NOHZ kconfig modes:
- CONFIG_HZ_PERIODIC: [formerly !CONFIG_NO_HZ], now explicitly named
as a config option. This is the traditional Linux periodic tick
design: there's a HZ tick going on all the time, regardless of
whether a CPU is idle or not.
- CONFIG_NO_HZ_IDLE: [formerly CONFIG_NO_HZ=y], this turns off the
periodic tick when a CPU enters idle mode.
- CONFIG_NO_HZ_FULL: this new mode, in addition to turning off the
tick when a CPU is idle, also slows the tick down to 1 Hz (one
timer interrupt per second) when only a single task is running on a
CPU.
The .config behavior is compatible: existing !CONFIG_NO_HZ and
CONFIG_NO_HZ=y settings get translated to the new values, without the
user having to configure anything. CONFIG_NO_HZ_FULL is turned off by
default.
This feature is based on a lot of infrastructure work that has been
steadily going upstream in the last 2-3 cycles: related RCU support
and non-periodic cputime support in particular is upstream already.
This tree adds the final pieces and activates the feature. The pull
request is marked RFC because:
- it's marked 64-bit only at the moment - the 32-bit support patch is
small but did not get ready in time.
- it has a number of fresh commits that came in after the merge
window. The overwhelming majority of commits are from before the
merge window, but still some aspects of the tree are fresh and so I
marked it RFC.
- it's a pretty wide-reaching feature with lots of effects - and
while the components have been in testing for some time, the full
combination is still not very widely used. That it's default-off
should reduce its regression abilities and obviously there are no
known regressions with CONFIG_NO_HZ_FULL=y enabled either.
- the feature is not completely idempotent: there is no 100%
equivalent replacement for a periodic scheduler/timer tick. In
particular there's ongoing work to map out and reduce its effects
on scheduler load-balancing and statistics. This should not impact
correctness though, there are no known regressions related to this
feature at this point.
- it's a pretty ambitious feature that with time will likely be
enabled by most Linux distros, and we'd like you to make input on
its design/implementation, if you dislike some aspect we missed.
Without flaming us to crisp! :-)
Future plans:
- there's ongoing work to reduce 1Hz to 0Hz, to essentially shut off
the periodic tick altogether when there's a single busy task on a
CPU. We'd first like 1 Hz to be exposed more widely before we go
for the 0 Hz target though.
- once we reach 0 Hz we can remove the periodic tick assumption from
nr_running>=2 as well, by essentially interrupting busy tasks only
as frequently as the sched_latency constraints require us to do -
once every 4-40 msecs, depending on nr_running.
I am personally leaning towards biting the bullet and doing this in
v3.10, like the -rt tree this effort has been going on for too long -
but the final word is up to you as usual.
More technical details can be found in Documentation/timers/NO_HZ.txt"
* 'timers-nohz-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (39 commits)
sched: Keep at least 1 tick per second for active dynticks tasks
rcu: Fix full dynticks' dependency on wide RCU nocb mode
nohz: Protect smp_processor_id() in tick_nohz_task_switch()
nohz_full: Add documentation.
cputime_nsecs: use math64.h for nsec resolution conversion helpers
nohz: Select VIRT_CPU_ACCOUNTING_GEN from full dynticks config
nohz: Reduce overhead under high-freq idling patterns
nohz: Remove full dynticks' superfluous dependency on RCU tree
nohz: Fix unavailable tick_stop tracepoint in dynticks idle
nohz: Add basic tracing
nohz: Select wide RCU nocb for full dynticks
nohz: Disable the tick when irq resume in full dynticks CPU
nohz: Re-evaluate the tick for the new task after a context switch
nohz: Prepare to stop the tick on irq exit
nohz: Implement full dynticks kick
nohz: Re-evaluate the tick from the scheduler IPI
sched: New helper to prevent from stopping the tick in full dynticks
sched: Kick full dynticks CPU that have more than one task enqueued.
perf: New helper to prevent full dynticks CPUs from stopping tick
perf: Kick full dynticks CPU if events rotation is needed
...
Pull perf fixes from Ingo Molnar:
"Misc fixes plus a small hw-enablement patch for Intel IB model 58
uncore events"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel/lbr: Demand proper privileges for PERF_SAMPLE_BRANCH_KERNEL
perf/x86/intel/lbr: Fix LBR filter
perf/x86: Blacklist all MEM_*_RETIRED events for Ivy Bridge
perf: Fix vmalloc ring buffer pages handling
perf/x86/intel: Fix unintended variable name reuse
perf/x86/intel: Add support for IvyBridge model 58 Uncore
perf/x86/intel: Fix typo in perf_event_intel_uncore.c
x86: Eliminate irq_mis_count counted in arch_irq_stat
fix a remove/insert race which Never Happens, and (my favorite) handle the
case when we have too many modules for a single commandline. Seriously,
the kernel is full, please go away!
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=MPiD
-----END PGP SIGNATURE-----
Merge tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull mudule updates from Rusty Russell:
"We get rid of the general module prefix confusion with a binary config
option, fix a remove/insert race which Never Happens, and (my
favorite) handle the case when we have too many modules for a single
commandline. Seriously, the kernel is full, please go away!"
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
modpost: fix unwanted VMLINUX_SYMBOL_STR expansion
X.509: Support parse long form of length octets in Authority Key Identifier
module: don't unlink the module until we've removed all exposure.
kernel: kallsyms: memory override issue, need check destination buffer length
MODSIGN: do not send garbage to stderr when enabling modules signature
modpost: handle huge numbers of modules.
modpost: add -T option to read module names from file/stdin.
modpost: minor cleanup.
genksyms: pass symbol-prefix instead of arch
module: fix symbol versioning with symbol prefixes
CONFIG_SYMBOL_PREFIX: cleanup.
Pull single_open() leak fixes from Al Viro:
"A bunch of fixes for a moderately common class of bugs: file with
single_open() done by its ->open() and seq_release as its ->release().
That leaks; fortunately, it's not _too_ common (either people manage
to RTFM that says "When using single_open(), the programmer should use
single_release() instead of seq_release() in the file_operations
structure to avoid a memory leak", or they just copy a correct
instance), but grepping through the tree has caught quite a pile.
All of that is, AFAICS, -stable fodder, for as far as the patches
apply. I tried to carve it up into reasonably-sized pieces (more or
less "comes from the same tree")"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
rcutrace: single_open() leaks
gadget: single_open() leaks
staging: single_open() leaks
megaraid: single_open() leak
wireless: single_open() leaks
input: single_open() leak
rtc: single_open() leaks
ds1620: single_open() leak
sh: single_open() leaks
parisc: single_open() leaks
mips: single_open() leaks
ia64: single_open() leaks
h8300: single_open() leaks
cris: single_open() leaks
arm: single_open() leaks
commit d1669912 (idle: Implement generic idle function) added a new
generic idle along with support for hlt/nohlt command line options to
override default idle loop behavior. However, the command-line
processing is never compiled.
The command-line handling is wrapped by CONFIG_GENERIC_IDLE_POLL_SETUP
and arches that use this feature select it in their Kconfigs.
However, no Kconfig definition was created for this option, so it is
never enabled, and therefore command-line override of the idle-loop
behavior is broken after migrating to the generic idle loop.
To fix, add a Kconfig definition for GENERIC_IDLE_POLL_SETUP.
Tested on ARM (OMAP4/Panda) which enables the command-line overrides
by default.
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linaro-kernel@lists.linaro.org
Link: http://lkml.kernel.org/r/1366849153-25564-1-git-send-email-khilman@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Christoph Fritz