This patch introduce the needed vpdma API changes to support
user space specified stride instead of forcing a driver calculated
one.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add RAW8 and RAW16 data type to VPDMA.
To handle RAW format we are re-using the YUV CBY422
vpdma data type so that we use the vpdma to re-order
the incoming bytes, as the VIP parser assumes that the
first byte presented on the bus is the MSB of a 2
bytes value.
RAW8 handles from 1 to 8 bits.
RAW16 handles from 9 to 16 bits.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
vpdma_create API is supposed to allocated the struct vpdma_data and
return it to the driver. Also, it would call the callback function
when the VPDMA firmware is loaded.
Typically, VPE driver have following function call:
dev->vpdma = vpdma_create(pdev, firmware_load_callback);
And the callback implementation would continue the probe further.
Also, the dev->vpdma is accessed from the callback implementation.
This may lead to race condition between assignment of dev->vpdma
and the callback function being triggered.
This would lead to kernel crash because of NULL pointer access.
Fix this by passing a driver wrapped &vpdma_data instead of allocating
inside vpdma_create.
Change the vpdma_create prototype accordingly and fix return paths.
Also, update the VPE driver to use the updated API and
initialize the dev->vpdma before hand so that the race condition
is avoided.
Signed-off-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The YUV data type definition below are taken from
both the TRM and i839 Errata information.
Use the correct data type considering byte
reordering of components.
Added the 2 missing YUV422 variant.
Also since the single use of "C" in the 422 case
to mean "Cr" (i.e. V component). It was decided
to explicitly label them CR to remove any confusion.
Bear in mind that the type label refer to the memory
packed order (LSB - MSB).
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
VPDMA block used in ti-vip and ti-vpe modules have support for
up to 8 hardware descriptor lists. A descriptor list can be
submitted to any of the 8 lists (as long as it's not busy).
When multiple clients want to transfer data in parallel, its easier
to allocate one list per client and let it use it. This way, the
list numbers need not be hard-coded into the driver.
Add support for allocating hwlist and maintain them with a priv data.
Signed-off-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
VPDMA IRQs are registered for multiple lists
When clearing an IRQ for a list interrupt, all the
IRQs for the individual lists are to be cleared separately.
Signed-off-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Writing to the "VPDMA list attribute" register is considered as a list
post. This informs the VPDMA firmware to load the list from the address
which should be taken from the "VPDMA list address" register.
As these two register writes are dependent, it is important that the two
writes happen in atomic manner. This ensures multiple slices (which share
same VPDMA) can post lists asynchronously and all of them point to the
correct addresses.
Slightly modified to implementation for the original patch to use
spin_lock instead of mutex as the list post is also called from
interrupt context.
Signed-off-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Whenever VPDMA processes a data descriptor of a list, it processes it
and sets up the channel for the DMA transaction. List manager holds the
descriptor in the list until the DMA is complete. If sync_on_channel
descriptor, or another descriptor for the same channel is present in
the FIFO, list manager keeps them until the current channel is free.
When the capture stream is closed suddenly while there are pending
descriptors in the FIFO (streamON failed, application killed), it would
keep the VPDMA in a busy state. Any further list post would fail with
EBUSY.
To avoid this, drivers need to stop the current processing list and
cleanup all the resources VPDMA has taken and also clear the internal FSM
of list manager. The state machine is cleared by issuing channel specific
abort descriptor.
Therefore, the vpdma_list_cleanup accepts an array of channels for which
abort_channel descriptors should be posted. It is driver's responsibility
to post for all the channels or the channels which were used in the last
context.
Signed-off-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add a helper function to be able to set the maximum
VPDMA transfer size to limit potential buffer overrun.
Added enums for max_width and max_height fields of the
outbound data descriptor.
Changed vpdma_add_out_dtd to accept two more arguments
for max width and height.
Make use of different max width & height sets for different
of capture module (i.e. slices).
Signed-off-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add a helper to set the background color during vpdma transfer.
This is needed when VPDMA is generating 32 bits RGB format
to have the Alpha channel set to an appropriate value.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The VPDMA (Video Port DMA) as found in devices such as DRA7xx is
used for both the Video Processing Engine (VPE) and the Video Input
Port (VIP). Some devices may have multiple VIP instances each with
its own VPDMA engine. Within VIP two slices can use a single VPDMA
engine simultaneously. So support for multi instances and multiple
clients has been added to VPDMA. Needed modification to the existing
helper functions were then reflected to VPE.
Multi-clients registers offset have also been added in preparation.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some parameters of the VPE descriptors were understood incorrectly. They are now
fixed. The fixes are explained as follows:
- When adding an inbound data descriptor to the VPDMA descriptor list, we intend
to use c_rect as the cropped region fetched by VPDMA. Therefore, c_rect->width
shouldn't be used to calculate the line stride, the original image width
should be used for that. We add a 'width' argument which gives the buffer
width in memory.
- frame_width and frame_height describe the complete width and height of the
client to which the channel is connected. If there are multiple channels
fetching data and providing to the same client, the above 2 arguments should
be the width and height of the region covered by all the channels. In the case
where there is only one channel providing pixel data to the client
(like in VPE), frame_width and frame_height should be the cropped width and
cropped height respectively. The calculation of these params is done in the
vpe driver now.
- start_h and start_v is also used in the case of multiple channels to describe
where each channel should start filling pixel data. We don't use this in VPE,
and pass 0s to the vpdma_add_in_dtd() helper.
- Some minor changes are made to the vpdma_add_out_dtd() helper. The c_rect
param is used for specifying the 'composition' target, and 'width' is added
to calculate the line stride.
Signed-off-by: Archit Taneja <archit@ti.com>
Acked-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
vpe fops(vpe_open in particular) should be called only when VPDMA firmware
is loaded. File operations on the video device are possible the moment it is
registered.
Currently, we register the video device for VPE at driver probe, after calling
a vpdma helper to initialize VPDMA and load firmware. This function is
non-blocking(it calls request_firmware_nowait()), and doesn't ensure that the
firmware is actually loaded when it returns.
We remove the device registration from vpe probe, and move it to a callback
provided by the vpe driver to the vpdma library, through vpdma_create().
The ready field in vpdma_data is no longer needed since we always have firmware
loaded before the device is registered.
A minor problem with this approach is that if the video_register_device
fails(which doesn't really happen), the vpe platform device would be registered.
however, there won't be any v4l2 device corresponding to it.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The struct vpdma_data_format holds the color format depth and the data_type
value needed to be programmed in the data descriptors. However, it doesn't
tell what type of color format is it, i.e, whether it is RGB, YUV or Misc.
This information is needed when by vpdma library when forming descriptors. We
modify the depth parameter for the chroma portion of the NV12 format. For this,
we check if the data_type value is C420. This isn't sufficient as there are
many YUV and RGB vpdma formats which have the same data_type value. Hence, we
need to hold the type of the color format for the above case, and possibly more
cases in the future.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When VPDMA fetches or writes to an image buffer, the line stride must be a
multiple of 16 bytes. If it isn't, VPDMA HW will write/fetch until the next
16 byte boundry. This causes VPE to work incorrectly for source or destination
widths which don't satisfy the above alignment requirement.
In order to prevent this, we now make sure that when we set pix format for the
input and output buffers, the VPE source and destination image line strides are
16 byte aligned. Also, the motion vector buffers for the de-interlacer are
allocated in such a way that it ensures the same alignment.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Create functions which the VPE driver can use to create a VPDMA
descriptor and add it to a VPDMA descriptor list. These functions take a
pointer to an existing list, and append the configuration/data/control
descriptor header to the list.
In the case of configuration descriptors, the creation of a payload
block may be required(the payloads can hold VPE MMR values, or scaler
coefficients). The allocation of the payload buffer and it's content is
left to the VPE driver. However, the VPDMA library provides helper
macros to create payload in the correct format.
Add debug functions to dump the descriptors in a way such that it's easy
to see the values of different fields in the descriptors.
Signed-off-by: Archit Taneja <archit@ti.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The primary function of VPDMA is to move data between external memory
and internal processing modules(in our case, VPE) that source or sink
data. VPDMA is capable of buffering this data and then delivering the
data as demanded to the modules as programmed. The modules that source
or sink data are referred to as clients or ports. A channel is setup
inside the VPDMA to connect a specific memory buffer to a specific
client. The VPDMA centralizes the DMA control functions and buffering
required to allow all the clients to minimize the effect of long latency
times.
Add the following to the VPDMA helper:
- A data struct which describe VPDMA channels. For now, these channels
are the ones used only by VPE, the list of channels will increase when
VIP(Video Input Port) also uses the VPDMA library. This channel
information will be used to populate fields required by data
descriptors.
- Data structs which describe the different data types supported by
VPDMA. This data type information will be used to populate fields
required by data descriptors and used by the VPE driver to map a V4L2
format to the corresponding VPDMA data type.
- Provide VPDMA register offset definitions, functions to read, write
and modify VPDMA registers.
- Functions to create and submit a VPDMA list. A list is a group of
descriptors that makes up a set of DMA transfers that need to be
completed. Each descriptor will either perform a DMA transaction to
fetch input buffers and write to output buffers(data descriptors), or
configure the MMRs of sub blocks of VPE(configuration descriptors), or
provide control information to VPDMA (control descriptors).
- Functions to allocate, map and unmap buffers needed for the descriptor
list, payloads containing MMR values and scaler coefficients. These use
the DMA mapping APIs to ensure exclusive access to VPDMA.
- Functions to enable VPDMA interrupts. VPDMA can trigger an interrupt
on the VPE interrupt line when a descriptor list is parsed completely
and the DMA transactions are completed. This requires masking the events
in VPDMA registers and configuring some top level VPE interrupt
registers.
- Enable some VPDMA specific parameters: frame start event(when to start
DMA for a client) and line mode(whether each line fetched should be
mirrored or not).
- Function to load firmware required by VPDMA. VPDMA requires a firmware
for it's internal list manager. We add the required request_firmware
apis to fetch this firmware from user space.
- Function to dump VPDMA registers.
- A function to initialize and create a VPDMA instance, this will be
called by the VPE driver with it's platform device pointer, this
function will take care of loading VPDMA firmware and returning a
vpdma_data instance back to the VPE driver. The VIP driver will also
call the same init function to initialize it's own VPDMA instance.
Signed-off-by: Archit Taneja <archit@ti.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Benoit Parrot