Currently of_mdiobus_register() function registers all PHY devices,
independetly from their status property in device tree. According to
"ePAPR 1.1" spec, device should only be registered if there is no
"status" property, or it has "ok" (or "okay") value (see
of_device_is_available()). In case of "platform devices",
of_platform_device_create_pdata() checks for "status" and ensures
that disabled devices are not pupulated. But such check for MDIO buses
was missing until now. Fix it.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@sysgo.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Define two new "compatible" values for Ethernet
PHYs. "ethernet-phy-ieee802.3-c22" and "ethernet-phy-ieee802.3-c45"
are used to indicate a PHY uses the corresponding protocol.
If a PHY is "compatible" with "ethernet-phy-ieee802.3-c45", we
indicate this so that get_phy_device() can properly probe the device.
If get_phy_device() fails, it was probably due to failing the probe of
the PHY identifier registers. Since we have the device tree telling
us the PHY exists, go ahead and add it anyhow with a phy_id of zero.
There may be a driver match based on the "compatible" property.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IEEE802.3 clause 45 MDIO bus protocol allows for directly
addressing PHY registers using a 21 bit address, and is used by many
10G Ethernet PHYS. Already existing is the ability of MDIO bus
drivers to use clause 45, with the MII_ADDR_C45 flag. Here we add
struct phy_c45_device_ids to hold the device identifier registers
present in clause 45. struct phy_device gets a couple of new fields:
c45_ids to hold the identifiers and is_c45 to signal that it is clause
45.
get_phy_device() gets a new parameter is_c45 to indicate that the PHY
device should use the clause 45 protocol, and its callers are adjusted
to pass false. The follow-on patch to of_mdio.c will pass true where
appropriate.
EXPORT phy_device_create() so that the follow-on patch to of_mdio.c
can use it to create phy devices for PHYs, that have non-standard
device identifier registers, based on the device tree bindings.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add of_mdio_find_bus() which allows an mii_bus to be located given its
associated the device tree node.
This is needed by the follow-on patch to add a driver for MDIO bus
multiplexers.
The of_mdiobus_register() function is modified so that the device tree
node is recorded in the mii_bus. Then we can find it again by
iterating over all mdio_bus_class devices.
Because the OF device tree has now become an integral part of the
kernel, this can live in mdio_bus.c (which contains the needed
mdio_bus_class structure) instead of of_mdio.c.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since 9e6c643b (phy/fixed: use an unique MDIO bus name) the name of the fixed
PHY bus is "fixed-0". Teach of_phy_connect_fixed_link() the new name.
Tested on a P1020RDB PowerPC system.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
The "phy_device_register()" call 5 lines down already calls
phy_scan_fixups(), there's no need to do it a second time.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
In of_mdiobus_register(), the __be32 *addr variable is dereferenced.
This will not work on little-endian targets. Also since it is
unsigned, checking for less than zero is redundant.
Fix these two issues.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
[grant.likely@secretlab.ca: removed goto]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Merge common code between PowerPC and Microblaze. SPARC implements
irq_of_parse_and_map(), but the implementation is different, so it
does not use this code.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Michal Simek <monstr@monstr.eu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Jeremy Kerr <jeremy.kerr@canonical.com>
Merging in current state of Linus' tree to deal with merge conflicts and
build failures in vio.c after merge.
Conflicts:
drivers/i2c/busses/i2c-cpm.c
drivers/i2c/busses/i2c-mpc.c
drivers/net/gianfar.c
Also fixed up one line in arch/powerpc/kernel/vio.c to use the
correct node pointer.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch eliminates the node pointer from struct of_device and the
of_node (or prom_node) pointer from struct dev_archdata since the node
pointer is now part of struct device proper when CONFIG_OF is set, and
all users of the old pointer locations have already been converted over
to use device->of_node.
Also remove dev_archdata_{get,set}_node() as it is no longer used by
anything.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The following structure elements duplicate the information in
'struct device.of_node' and so are being eliminated. This patch
makes all readers of these elements use device.of_node instead.
(struct of_device *)->node
(struct dev_archdata *)->prom_node (sparc)
(struct dev_archdata *)->of_node (powerpc & microblaze)
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Currently, platforms using CONFIG_OF add a 'struct device_node *of_node'
to dev->archdata. However, with CONFIG_OF becoming generic for all
architectures, it makes sense for commonality to move it out of archdata
and into struct device proper.
This patch adds a struct device_node *of_node member to struct device
and updates all locations which currently write the device_node pointer
into archdata to also update dev->of_node. Subsequent patches will
modify callers to use the archdata location and ultimately remove
the archdata member entirely.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
CC: Michal Simek <monstr@monstr.eu>
CC: Greg Kroah-Hartman <gregkh@suse.de>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: "David S. Miller" <davem@davemloft.net>
CC: Stephen Rothwell <sfr@canb.auug.org.au>
CC: Jeremy Kerr <jeremy.kerr@canonical.com>
CC: microblaze-uclinux@itee.uq.edu.au
CC: linux-kernel@vger.kernel.org
CC: linuxppc-dev@ozlabs.org
CC: sparclinux@vger.kernel.org
Properties in the device tree are specified as big-endian. At present,
the only platforms to support device trees are also big-endian, so we've
been acessing the properties as raw values.
We'd like to add device tree support to little-endian platforms too, so
add endian conversion to the sites where we access property values in
the common of code.
Compiled on powerpc (ppc44x_defconfig & ppc64_defconfig) and arm (fdt
support only for now).
Signed-off-by: Jeremy Kerr <jeremy.kerr@canonical.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Some toolchains dislike nested function definition, so we define function match
outside of of_phy_find_device.
Signed-off-by: Jérôme Pouiller <jezz@sysmic.org>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Fixed-link support is broken for the ucc_eth, gianfar, and fs_enet
device drivers. The "OF MDIO rework" patches removed most of the
support. Instead of re-adding fixed-link stuff to the drivers, this
patch adds a support function for parsing the fixed-link property
and obtaining a dummy phy to match.
Note: the dummy phy handling in arch/powerpc is a bit of a hack and
needs to be reworked. This function is being added now to solve the
regression in the Ethernet drivers, but it should be considered a
temporary measure until the fixed link handling can be reworked.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for parsing the device tree for PHY devices on an MDIO bus.
Currently many of the PowerPC ethernet drivers are open coding a solution
for reading data out of the device tree to find the correct PHY device.
This patch implements a set of common routines to:
a) let MDIO bus drivers register phy_devices described in the tree, and
b) let MAC drivers find the correct phy_device via the tree.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Sverdlin